projects / deliverable / linux.git / blob
? search:
summary | shortlog | log | commit | commitdiff | tree
blame | history | raw | HEAD
ext3: Flush disk caches on fsync when needed
[deliverable/linux.git] / drivers / net / sky2.c
1 /*
2 * New driver for Marvell Yukon 2 chipset.
3 * Based on earlier sk98lin, and skge driver.
4 *
5 * This driver intentionally does not support all the features
6 * of the original driver such as link fail-over and link management because
7 * those should be done at higher levels.
8 *
9 * Copyright (C) 2005 Stephen Hemminger <shemminger@osdl.org>
10 *
11 * This program is free software; you can redistribute it and/or modify
12 * it under the terms of the GNU General Public License as published by
13 * the Free Software Foundation; either version 2 of the License.
14 *
15 * This program is distributed in the hope that it will be useful,
16 * but WITHOUT ANY WARRANTY; without even the implied warranty of
17 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
18 * GNU General Public License for more details.
19 *
20 * You should have received a copy of the GNU General Public License
21 * along with this program; if not, write to the Free Software
22 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
23 */
24
25 #include <linux/crc32.h>
26 #include <linux/kernel.h>
27 #include <linux/module.h>
28 #include <linux/netdevice.h>
29 #include <linux/dma-mapping.h>
30 #include <linux/etherdevice.h>
31 #include <linux/ethtool.h>
32 #include <linux/pci.h>
33 #include <linux/ip.h>
34 #include <net/ip.h>
35 #include <linux/tcp.h>
36 #include <linux/in.h>
37 #include <linux/delay.h>
38 #include <linux/workqueue.h>
39 #include <linux/if_vlan.h>
40 #include <linux/prefetch.h>
41 #include <linux/debugfs.h>
42 #include <linux/mii.h>
43
44 #include <asm/irq.h>
45
46 #if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
47 #define SKY2_VLAN_TAG_USED 1
48 #endif
49
50 #include "sky2.h"
51
52 #define DRV_NAME "sky2"
53 #define DRV_VERSION "1.25"
54 #define PFX DRV_NAME " "
55
56 /*
57 * The Yukon II chipset takes 64 bit command blocks (called list elements)
58 * that are organized into three (receive, transmit, status) different rings
59 * similar to Tigon3.
60 */
61
62 #define RX_LE_SIZE 1024
63 #define RX_LE_BYTES (RX_LE_SIZE*sizeof(struct sky2_rx_le))
64 #define RX_MAX_PENDING (RX_LE_SIZE/6 - 2)
65 #define RX_DEF_PENDING RX_MAX_PENDING
66
67 /* This is the worst case number of transmit list elements for a single skb:
68 VLAN + TSO + CKSUM + Data + skb_frags * DMA */
69 #define MAX_SKB_TX_LE (4 + (sizeof(dma_addr_t)/sizeof(u32))*MAX_SKB_FRAGS)
70 #define TX_MIN_PENDING (MAX_SKB_TX_LE+1)
71 #define TX_MAX_PENDING 4096
72 #define TX_DEF_PENDING 127
73
74 #define STATUS_RING_SIZE 2048 /* 2 ports * (TX + 2*RX) */
75 #define STATUS_LE_BYTES (STATUS_RING_SIZE*sizeof(struct sky2_status_le))
76 #define TX_WATCHDOG (5 * HZ)
77 #define NAPI_WEIGHT 64
78 #define PHY_RETRIES 1000
79
80 #define SKY2_EEPROM_MAGIC 0x9955aabb
81
82
83 #define RING_NEXT(x,s) (((x)+1) & ((s)-1))
84
85 static const u32 default_msg =
86 NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK
87 | NETIF_MSG_TIMER | NETIF_MSG_TX_ERR | NETIF_MSG_RX_ERR
88 | NETIF_MSG_IFUP | NETIF_MSG_IFDOWN;
89
90 static int debug = -1; /* defaults above */
91 module_param(debug, int, 0);
92 MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
93
94 static int copybreak __read_mostly = 128;
95 module_param(copybreak, int, 0);
96 MODULE_PARM_DESC(copybreak, "Receive copy threshold");
97
98 static int disable_msi = 0;
99 module_param(disable_msi, int, 0);
100 MODULE_PARM_DESC(disable_msi, "Disable Message Signaled Interrupt (MSI)");
101
102 static DEFINE_PCI_DEVICE_TABLE(sky2_id_table) = {
103 { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9000) }, /* SK-9Sxx */
104 { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E00) }, /* SK-9Exx */
105 { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4b00) }, /* DGE-560T */
106 { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4001) }, /* DGE-550SX */
107 { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4B02) }, /* DGE-560SX */
108 { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4B03) }, /* DGE-550T */
109 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4340) }, /* 88E8021 */
110 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4341) }, /* 88E8022 */
111 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4342) }, /* 88E8061 */
112 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4343) }, /* 88E8062 */
113 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4344) }, /* 88E8021 */
114 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4345) }, /* 88E8022 */
115 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4346) }, /* 88E8061 */
116 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4347) }, /* 88E8062 */
117 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4350) }, /* 88E8035 */
118 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4351) }, /* 88E8036 */
119 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4352) }, /* 88E8038 */
120 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4353) }, /* 88E8039 */
121 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4354) }, /* 88E8040 */
122 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4355) }, /* 88E8040T */
123 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4356) }, /* 88EC033 */
124 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4357) }, /* 88E8042 */
125 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x435A) }, /* 88E8048 */
126 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4360) }, /* 88E8052 */
127 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4361) }, /* 88E8050 */
128 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4362) }, /* 88E8053 */
129 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4363) }, /* 88E8055 */
130 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4364) }, /* 88E8056 */
131 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4365) }, /* 88E8070 */
132 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4366) }, /* 88EC036 */
133 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4367) }, /* 88EC032 */
134 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4368) }, /* 88EC034 */
135 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4369) }, /* 88EC042 */
136 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436A) }, /* 88E8058 */
137 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436B) }, /* 88E8071 */
138 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436C) }, /* 88E8072 */
139 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436D) }, /* 88E8055 */
140 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4370) }, /* 88E8075 */
141 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4380) }, /* 88E8057 */
142 { 0 }
143 };
144
145 MODULE_DEVICE_TABLE(pci, sky2_id_table);
146
147 /* Avoid conditionals by using array */
148 static const unsigned txqaddr[] = { Q_XA1, Q_XA2 };
149 static const unsigned rxqaddr[] = { Q_R1, Q_R2 };
150 static const u32 portirq_msk[] = { Y2_IS_PORT_1, Y2_IS_PORT_2 };
151
152 static void sky2_set_multicast(struct net_device *dev);
153
154 /* Access to PHY via serial interconnect */
155 static int gm_phy_write(struct sky2_hw *hw, unsigned port, u16 reg, u16 val)
156 {
157 int i;
158
159 gma_write16(hw, port, GM_SMI_DATA, val);
160 gma_write16(hw, port, GM_SMI_CTRL,
161 GM_SMI_CT_PHY_AD(PHY_ADDR_MARV) | GM_SMI_CT_REG_AD(reg));
162
163 for (i = 0; i < PHY_RETRIES; i++) {
164 u16 ctrl = gma_read16(hw, port, GM_SMI_CTRL);
165 if (ctrl == 0xffff)
166 goto io_error;
167
168 if (!(ctrl & GM_SMI_CT_BUSY))
169 return 0;
170
171 udelay(10);
172 }
173
174 dev_warn(&hw->pdev->dev,"%s: phy write timeout\n", hw->dev[port]->name);
175 return -ETIMEDOUT;
176
177 io_error:
178 dev_err(&hw->pdev->dev, "%s: phy I/O error\n", hw->dev[port]->name);
179 return -EIO;
180 }
181
182 static int __gm_phy_read(struct sky2_hw *hw, unsigned port, u16 reg, u16 *val)
183 {
184 int i;
185
186 gma_write16(hw, port, GM_SMI_CTRL, GM_SMI_CT_PHY_AD(PHY_ADDR_MARV)
187 | GM_SMI_CT_REG_AD(reg) | GM_SMI_CT_OP_RD);
188
189 for (i = 0; i < PHY_RETRIES; i++) {
190 u16 ctrl = gma_read16(hw, port, GM_SMI_CTRL);
191 if (ctrl == 0xffff)
192 goto io_error;
193
194 if (ctrl & GM_SMI_CT_RD_VAL) {
195 *val = gma_read16(hw, port, GM_SMI_DATA);
196 return 0;
197 }
198
199 udelay(10);
200 }
201
202 dev_warn(&hw->pdev->dev, "%s: phy read timeout\n", hw->dev[port]->name);
203 return -ETIMEDOUT;
204 io_error:
205 dev_err(&hw->pdev->dev, "%s: phy I/O error\n", hw->dev[port]->name);
206 return -EIO;
207 }
208
209 static inline u16 gm_phy_read(struct sky2_hw *hw, unsigned port, u16 reg)
210 {
211 u16 v;
212 __gm_phy_read(hw, port, reg, &v);
213 return v;
214 }
215
216
217 static void sky2_power_on(struct sky2_hw *hw)
218 {
219 /* switch power to VCC (WA for VAUX problem) */
220 sky2_write8(hw, B0_POWER_CTRL,
221 PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_OFF | PC_VCC_ON);
222
223 /* disable Core Clock Division, */
224 sky2_write32(hw, B2_Y2_CLK_CTRL, Y2_CLK_DIV_DIS);
225
226 if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
227 /* enable bits are inverted */
228 sky2_write8(hw, B2_Y2_CLK_GATE,
229 Y2_PCI_CLK_LNK1_DIS | Y2_COR_CLK_LNK1_DIS |
230 Y2_CLK_GAT_LNK1_DIS | Y2_PCI_CLK_LNK2_DIS |
231 Y2_COR_CLK_LNK2_DIS | Y2_CLK_GAT_LNK2_DIS);
232 else
233 sky2_write8(hw, B2_Y2_CLK_GATE, 0);
234
235 if (hw->flags & SKY2_HW_ADV_POWER_CTL) {
236 u32 reg;
237
238 sky2_pci_write32(hw, PCI_DEV_REG3, 0);
239
240 reg = sky2_pci_read32(hw, PCI_DEV_REG4);
241 /* set all bits to 0 except bits 15..12 and 8 */
242 reg &= P_ASPM_CONTROL_MSK;
243 sky2_pci_write32(hw, PCI_DEV_REG4, reg);
244
245 reg = sky2_pci_read32(hw, PCI_DEV_REG5);
246 /* set all bits to 0 except bits 28 & 27 */
247 reg &= P_CTL_TIM_VMAIN_AV_MSK;
248 sky2_pci_write32(hw, PCI_DEV_REG5, reg);
249
250 sky2_pci_write32(hw, PCI_CFG_REG_1, 0);
251
252 /* Enable workaround for dev 4.107 on Yukon-Ultra & Extreme */
253 reg = sky2_read32(hw, B2_GP_IO);
254 reg |= GLB_GPIO_STAT_RACE_DIS;
255 sky2_write32(hw, B2_GP_IO, reg);
256
257 sky2_read32(hw, B2_GP_IO);
258 }
259
260 /* Turn on "driver loaded" LED */
261 sky2_write16(hw, B0_CTST, Y2_LED_STAT_ON);
262 }
263
264 static void sky2_power_aux(struct sky2_hw *hw)
265 {
266 if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
267 sky2_write8(hw, B2_Y2_CLK_GATE, 0);
268 else
269 /* enable bits are inverted */
270 sky2_write8(hw, B2_Y2_CLK_GATE,
271 Y2_PCI_CLK_LNK1_DIS | Y2_COR_CLK_LNK1_DIS |
272 Y2_CLK_GAT_LNK1_DIS | Y2_PCI_CLK_LNK2_DIS |
273 Y2_COR_CLK_LNK2_DIS | Y2_CLK_GAT_LNK2_DIS);
274
275 /* switch power to VAUX if supported and PME from D3cold */
276 if ( (sky2_read32(hw, B0_CTST) & Y2_VAUX_AVAIL) &&
277 pci_pme_capable(hw->pdev, PCI_D3cold))
278 sky2_write8(hw, B0_POWER_CTRL,
279 (PC_VAUX_ENA | PC_VCC_ENA |
280 PC_VAUX_ON | PC_VCC_OFF));
281
282 /* turn off "driver loaded LED" */
283 sky2_write16(hw, B0_CTST, Y2_LED_STAT_OFF);
284 }
285
286 static void sky2_gmac_reset(struct sky2_hw *hw, unsigned port)
287 {
288 u16 reg;
289
290 /* disable all GMAC IRQ's */
291 sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), 0);
292
293 gma_write16(hw, port, GM_MC_ADDR_H1, 0); /* clear MC hash */
294 gma_write16(hw, port, GM_MC_ADDR_H2, 0);
295 gma_write16(hw, port, GM_MC_ADDR_H3, 0);
296 gma_write16(hw, port, GM_MC_ADDR_H4, 0);
297
298 reg = gma_read16(hw, port, GM_RX_CTRL);
299 reg |= GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA;
300 gma_write16(hw, port, GM_RX_CTRL, reg);
301 }
302
303 /* flow control to advertise bits */
304 static const u16 copper_fc_adv[] = {
305 [FC_NONE] = 0,
306 [FC_TX] = PHY_M_AN_ASP,
307 [FC_RX] = PHY_M_AN_PC,
308 [FC_BOTH] = PHY_M_AN_PC | PHY_M_AN_ASP,
309 };
310
311 /* flow control to advertise bits when using 1000BaseX */
312 static const u16 fiber_fc_adv[] = {
313 [FC_NONE] = PHY_M_P_NO_PAUSE_X,
314 [FC_TX] = PHY_M_P_ASYM_MD_X,
315 [FC_RX] = PHY_M_P_SYM_MD_X,
316 [FC_BOTH] = PHY_M_P_BOTH_MD_X,
317 };
318
319 /* flow control to GMA disable bits */
320 static const u16 gm_fc_disable[] = {
321 [FC_NONE] = GM_GPCR_FC_RX_DIS | GM_GPCR_FC_TX_DIS,
322 [FC_TX] = GM_GPCR_FC_RX_DIS,
323 [FC_RX] = GM_GPCR_FC_TX_DIS,
324 [FC_BOTH] = 0,
325 };
326
327
328 static void sky2_phy_init(struct sky2_hw *hw, unsigned port)
329 {
330 struct sky2_port *sky2 = netdev_priv(hw->dev[port]);
331 u16 ctrl, ct1000, adv, pg, ledctrl, ledover, reg;
332
333 if ( (sky2->flags & SKY2_FLAG_AUTO_SPEED) &&
334 !(hw->flags & SKY2_HW_NEWER_PHY)) {
335 u16 ectrl = gm_phy_read(hw, port, PHY_MARV_EXT_CTRL);
336
337 ectrl &= ~(PHY_M_EC_M_DSC_MSK | PHY_M_EC_S_DSC_MSK |
338 PHY_M_EC_MAC_S_MSK);
339 ectrl |= PHY_M_EC_MAC_S(MAC_TX_CLK_25_MHZ);
340
341 /* on PHY 88E1040 Rev.D0 (and newer) downshift control changed */
342 if (hw->chip_id == CHIP_ID_YUKON_EC)
343 /* set downshift counter to 3x and enable downshift */
344 ectrl |= PHY_M_EC_DSC_2(2) | PHY_M_EC_DOWN_S_ENA;
345 else
346 /* set master & slave downshift counter to 1x */
347 ectrl |= PHY_M_EC_M_DSC(0) | PHY_M_EC_S_DSC(1);
348
349 gm_phy_write(hw, port, PHY_MARV_EXT_CTRL, ectrl);
350 }
351
352 ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
353 if (sky2_is_copper(hw)) {
354 if (!(hw->flags & SKY2_HW_GIGABIT)) {
355 /* enable automatic crossover */
356 ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO) >> 1;
357
358 if (hw->chip_id == CHIP_ID_YUKON_FE_P &&
359 hw->chip_rev == CHIP_REV_YU_FE2_A0) {
360 u16 spec;
361
362 /* Enable Class A driver for FE+ A0 */
363 spec = gm_phy_read(hw, port, PHY_MARV_FE_SPEC_2);
364 spec |= PHY_M_FESC_SEL_CL_A;
365 gm_phy_write(hw, port, PHY_MARV_FE_SPEC_2, spec);
366 }
367 } else {
368 /* disable energy detect */
369 ctrl &= ~PHY_M_PC_EN_DET_MSK;
370
371 /* enable automatic crossover */
372 ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO);
373
374 /* downshift on PHY 88E1112 and 88E1149 is changed */
375 if ( (sky2->flags & SKY2_FLAG_AUTO_SPEED)
376 && (hw->flags & SKY2_HW_NEWER_PHY)) {
377 /* set downshift counter to 3x and enable downshift */
378 ctrl &= ~PHY_M_PC_DSC_MSK;
379 ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA;
380 }
381 }
382 } else {
383 /* workaround for deviation #4.88 (CRC errors) */
384 /* disable Automatic Crossover */
385
386 ctrl &= ~PHY_M_PC_MDIX_MSK;
387 }
388
389 gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
390
391 /* special setup for PHY 88E1112 Fiber */
392 if (hw->chip_id == CHIP_ID_YUKON_XL && (hw->flags & SKY2_HW_FIBRE_PHY)) {
393 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
394
395 /* Fiber: select 1000BASE-X only mode MAC Specific Ctrl Reg. */
396 gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2);
397 ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
398 ctrl &= ~PHY_M_MAC_MD_MSK;
399 ctrl |= PHY_M_MAC_MODE_SEL(PHY_M_MAC_MD_1000BX);
400 gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
401
402 if (hw->pmd_type == 'P') {
403 /* select page 1 to access Fiber registers */
404 gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 1);
405
406 /* for SFP-module set SIGDET polarity to low */
407 ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
408 ctrl |= PHY_M_FIB_SIGD_POL;
409 gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
410 }
411
412 gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
413 }
414
415 ctrl = PHY_CT_RESET;
416 ct1000 = 0;
417 adv = PHY_AN_CSMA;
418 reg = 0;
419
420 if (sky2->flags & SKY2_FLAG_AUTO_SPEED) {
421 if (sky2_is_copper(hw)) {
422 if (sky2->advertising & ADVERTISED_1000baseT_Full)
423 ct1000 |= PHY_M_1000C_AFD;
424 if (sky2->advertising & ADVERTISED_1000baseT_Half)
425 ct1000 |= PHY_M_1000C_AHD;
426 if (sky2->advertising & ADVERTISED_100baseT_Full)
427 adv |= PHY_M_AN_100_FD;
428 if (sky2->advertising & ADVERTISED_100baseT_Half)
429 adv |= PHY_M_AN_100_HD;
430 if (sky2->advertising & ADVERTISED_10baseT_Full)
431 adv |= PHY_M_AN_10_FD;
432 if (sky2->advertising & ADVERTISED_10baseT_Half)
433 adv |= PHY_M_AN_10_HD;
434
435 } else { /* special defines for FIBER (88E1040S only) */
436 if (sky2->advertising & ADVERTISED_1000baseT_Full)
437 adv |= PHY_M_AN_1000X_AFD;
438 if (sky2->advertising & ADVERTISED_1000baseT_Half)
439 adv |= PHY_M_AN_1000X_AHD;
440 }
441
442 /* Restart Auto-negotiation */
443 ctrl |= PHY_CT_ANE | PHY_CT_RE_CFG;
444 } else {
445 /* forced speed/duplex settings */
446 ct1000 = PHY_M_1000C_MSE;
447
448 /* Disable auto update for duplex flow control and duplex */
449 reg |= GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_SPD_DIS;
450
451 switch (sky2->speed) {
452 case SPEED_1000:
453 ctrl |= PHY_CT_SP1000;
454 reg |= GM_GPCR_SPEED_1000;
455 break;
456 case SPEED_100:
457 ctrl |= PHY_CT_SP100;
458 reg |= GM_GPCR_SPEED_100;
459 break;
460 }
461
462 if (sky2->duplex == DUPLEX_FULL) {
463 reg |= GM_GPCR_DUP_FULL;
464 ctrl |= PHY_CT_DUP_MD;
465 } else if (sky2->speed < SPEED_1000)
466 sky2->flow_mode = FC_NONE;
467 }
468
469 if (sky2->flags & SKY2_FLAG_AUTO_PAUSE) {
470 if (sky2_is_copper(hw))
471 adv |= copper_fc_adv[sky2->flow_mode];
472 else
473 adv |= fiber_fc_adv[sky2->flow_mode];
474 } else {
475 reg |= GM_GPCR_AU_FCT_DIS;
476 reg |= gm_fc_disable[sky2->flow_mode];
477
478 /* Forward pause packets to GMAC? */
479 if (sky2->flow_mode & FC_RX)
480 sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON);
481 else
482 sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
483 }
484
485 gma_write16(hw, port, GM_GP_CTRL, reg);
486
487 if (hw->flags & SKY2_HW_GIGABIT)
488 gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, ct1000);
489
490 gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, adv);
491 gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
492
493 /* Setup Phy LED's */
494 ledctrl = PHY_M_LED_PULS_DUR(PULS_170MS);
495 ledover = 0;
496
497 switch (hw->chip_id) {
498 case CHIP_ID_YUKON_FE:
499 /* on 88E3082 these bits are at 11..9 (shifted left) */
500 ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) << 1;
501
502 ctrl = gm_phy_read(hw, port, PHY_MARV_FE_LED_PAR);
503
504 /* delete ACT LED control bits */
505 ctrl &= ~PHY_M_FELP_LED1_MSK;
506 /* change ACT LED control to blink mode */
507 ctrl |= PHY_M_FELP_LED1_CTRL(LED_PAR_CTRL_ACT_BL);
508 gm_phy_write(hw, port, PHY_MARV_FE_LED_PAR, ctrl);
509 break;
510
511 case CHIP_ID_YUKON_FE_P:
512 /* Enable Link Partner Next Page */
513 ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
514 ctrl |= PHY_M_PC_ENA_LIP_NP;
515
516 /* disable Energy Detect and enable scrambler */
517 ctrl &= ~(PHY_M_PC_ENA_ENE_DT | PHY_M_PC_DIS_SCRAMB);
518 gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
519
520 /* set LED2 -> ACT, LED1 -> LINK, LED0 -> SPEED */
521 ctrl = PHY_M_FELP_LED2_CTRL(LED_PAR_CTRL_ACT_BL) |
522 PHY_M_FELP_LED1_CTRL(LED_PAR_CTRL_LINK) |
523 PHY_M_FELP_LED0_CTRL(LED_PAR_CTRL_SPEED);
524
525 gm_phy_write(hw, port, PHY_MARV_FE_LED_PAR, ctrl);
526 break;
527
528 case CHIP_ID_YUKON_XL:
529 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
530
531 /* select page 3 to access LED control register */
532 gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
533
534 /* set LED Function Control register */
535 gm_phy_write(hw, port, PHY_MARV_PHY_CTRL,
536 (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */
537 PHY_M_LEDC_INIT_CTRL(7) | /* 10 Mbps */
538 PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */
539 PHY_M_LEDC_STA0_CTRL(7))); /* 1000 Mbps */
540
541 /* set Polarity Control register */
542 gm_phy_write(hw, port, PHY_MARV_PHY_STAT,
543 (PHY_M_POLC_LS1_P_MIX(4) |
544 PHY_M_POLC_IS0_P_MIX(4) |
545 PHY_M_POLC_LOS_CTRL(2) |
546 PHY_M_POLC_INIT_CTRL(2) |
547 PHY_M_POLC_STA1_CTRL(2) |
548 PHY_M_POLC_STA0_CTRL(2)));
549
550 /* restore page register */
551 gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
552 break;
553
554 case CHIP_ID_YUKON_EC_U:
555 case CHIP_ID_YUKON_EX:
556 case CHIP_ID_YUKON_SUPR:
557 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
558
559 /* select page 3 to access LED control register */
560 gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
561
562 /* set LED Function Control register */
563 gm_phy_write(hw, port, PHY_MARV_PHY_CTRL,
564 (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */
565 PHY_M_LEDC_INIT_CTRL(8) | /* 10 Mbps */
566 PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */
567 PHY_M_LEDC_STA0_CTRL(7)));/* 1000 Mbps */
568
569 /* set Blink Rate in LED Timer Control Register */
570 gm_phy_write(hw, port, PHY_MARV_INT_MASK,
571 ledctrl | PHY_M_LED_BLINK_RT(BLINK_84MS));
572 /* restore page register */
573 gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
574 break;
575
576 default:
577 /* set Tx LED (LED_TX) to blink mode on Rx OR Tx activity */
578 ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) | PHY_M_LEDC_TX_CTRL;
579
580 /* turn off the Rx LED (LED_RX) */
581 ledover |= PHY_M_LED_MO_RX(MO_LED_OFF);
582 }
583
584 if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_UL_2) {
585 /* apply fixes in PHY AFE */
586 gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 255);
587
588 /* increase differential signal amplitude in 10BASE-T */
589 gm_phy_write(hw, port, 0x18, 0xaa99);
590 gm_phy_write(hw, port, 0x17, 0x2011);
591
592 if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
593 /* fix for IEEE A/B Symmetry failure in 1000BASE-T */
594 gm_phy_write(hw, port, 0x18, 0xa204);
595 gm_phy_write(hw, port, 0x17, 0x2002);
596 }
597
598 /* set page register to 0 */
599 gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0);
600 } else if (hw->chip_id == CHIP_ID_YUKON_FE_P &&
601 hw->chip_rev == CHIP_REV_YU_FE2_A0) {
602 /* apply workaround for integrated resistors calibration */
603 gm_phy_write(hw, port, PHY_MARV_PAGE_ADDR, 17);
604 gm_phy_write(hw, port, PHY_MARV_PAGE_DATA, 0x3f60);
605 } else if (hw->chip_id != CHIP_ID_YUKON_EX &&
606 hw->chip_id < CHIP_ID_YUKON_SUPR) {
607 /* no effect on Yukon-XL */
608 gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
609
610 if ( !(sky2->flags & SKY2_FLAG_AUTO_SPEED)
611 || sky2->speed == SPEED_100) {
612 /* turn on 100 Mbps LED (LED_LINK100) */
613 ledover |= PHY_M_LED_MO_100(MO_LED_ON);
614 }
615
616 if (ledover)
617 gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
618
619 }
620
621 /* Enable phy interrupt on auto-negotiation complete (or link up) */
622 if (sky2->flags & SKY2_FLAG_AUTO_SPEED)
623 gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_COMPL);
624 else
625 gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
626 }
627
628 static const u32 phy_power[] = { PCI_Y2_PHY1_POWD, PCI_Y2_PHY2_POWD };
629 static const u32 coma_mode[] = { PCI_Y2_PHY1_COMA, PCI_Y2_PHY2_COMA };
630
631 static void sky2_phy_power_up(struct sky2_hw *hw, unsigned port)
632 {
633 u32 reg1;
634
635 sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
636 reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
637 reg1 &= ~phy_power[port];
638
639 if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
640 reg1 |= coma_mode[port];
641
642 sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
643 sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
644 sky2_pci_read32(hw, PCI_DEV_REG1);
645
646 if (hw->chip_id == CHIP_ID_YUKON_FE)
647 gm_phy_write(hw, port, PHY_MARV_CTRL, PHY_CT_ANE);
648 else if (hw->flags & SKY2_HW_ADV_POWER_CTL)
649 sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR);
650 }
651
652 static void sky2_phy_power_down(struct sky2_hw *hw, unsigned port)
653 {
654 u32 reg1;
655 u16 ctrl;
656
657 /* release GPHY Control reset */
658 sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR);
659
660 /* release GMAC reset */
661 sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR);
662
663 if (hw->flags & SKY2_HW_NEWER_PHY) {
664 /* select page 2 to access MAC control register */
665 gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2);
666
667 ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
668 /* allow GMII Power Down */
669 ctrl &= ~PHY_M_MAC_GMIF_PUP;
670 gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
671
672 /* set page register back to 0 */
673 gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0);
674 }
675
676 /* setup General Purpose Control Register */
677 gma_write16(hw, port, GM_GP_CTRL,
678 GM_GPCR_FL_PASS | GM_GPCR_SPEED_100 |
679 GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_FCT_DIS |
680 GM_GPCR_AU_SPD_DIS);
681
682 if (hw->chip_id != CHIP_ID_YUKON_EC) {
683 if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
684 /* select page 2 to access MAC control register */
685 gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2);
686
687 ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
688 /* enable Power Down */
689 ctrl |= PHY_M_PC_POW_D_ENA;
690 gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
691
692 /* set page register back to 0 */
693 gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0);
694 }
695
696 /* set IEEE compatible Power Down Mode (dev. #4.99) */
697 gm_phy_write(hw, port, PHY_MARV_CTRL, PHY_CT_PDOWN);
698 }
699
700 sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
701 reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
702 reg1 |= phy_power[port]; /* set PHY to PowerDown/COMA Mode */
703 sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
704 sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
705 }
706
707 /* Force a renegotiation */
708 static void sky2_phy_reinit(struct sky2_port *sky2)
709 {
710 spin_lock_bh(&sky2->phy_lock);
711 sky2_phy_init(sky2->hw, sky2->port);
712 spin_unlock_bh(&sky2->phy_lock);
713 }
714
715 /* Put device in state to listen for Wake On Lan */
716 static void sky2_wol_init(struct sky2_port *sky2)
717 {
718 struct sky2_hw *hw = sky2->hw;
719 unsigned port = sky2->port;
720 enum flow_control save_mode;
721 u16 ctrl;
722 u32 reg1;
723
724 /* Bring hardware out of reset */
725 sky2_write16(hw, B0_CTST, CS_RST_CLR);
726 sky2_write16(hw, SK_REG(port, GMAC_LINK_CTRL), GMLC_RST_CLR);
727
728 sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR);
729 sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR);
730
731 /* Force to 10/100
732 * sky2_reset will re-enable on resume
733 */
734 save_mode = sky2->flow_mode;
735 ctrl = sky2->advertising;
736
737 sky2->advertising &= ~(ADVERTISED_1000baseT_Half|ADVERTISED_1000baseT_Full);
738 sky2->flow_mode = FC_NONE;
739
740 spin_lock_bh(&sky2->phy_lock);
741 sky2_phy_power_up(hw, port);
742 sky2_phy_init(hw, port);
743 spin_unlock_bh(&sky2->phy_lock);
744
745 sky2->flow_mode = save_mode;
746 sky2->advertising = ctrl;
747
748 /* Set GMAC to no flow control and auto update for speed/duplex */
749 gma_write16(hw, port, GM_GP_CTRL,
750 GM_GPCR_FC_TX_DIS|GM_GPCR_TX_ENA|GM_GPCR_RX_ENA|
751 GM_GPCR_DUP_FULL|GM_GPCR_FC_RX_DIS|GM_GPCR_AU_FCT_DIS);
752
753 /* Set WOL address */
754 memcpy_toio(hw->regs + WOL_REGS(port, WOL_MAC_ADDR),
755 sky2->netdev->dev_addr, ETH_ALEN);
756
757 /* Turn on appropriate WOL control bits */
758 sky2_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), WOL_CTL_CLEAR_RESULT);
759 ctrl = 0;
760 if (sky2->wol & WAKE_PHY)
761 ctrl |= WOL_CTL_ENA_PME_ON_LINK_CHG|WOL_CTL_ENA_LINK_CHG_UNIT;
762 else
763 ctrl |= WOL_CTL_DIS_PME_ON_LINK_CHG|WOL_CTL_DIS_LINK_CHG_UNIT;
764
765 if (sky2->wol & WAKE_MAGIC)
766 ctrl |= WOL_CTL_ENA_PME_ON_MAGIC_PKT|WOL_CTL_ENA_MAGIC_PKT_UNIT;
767 else
768 ctrl |= WOL_CTL_DIS_PME_ON_MAGIC_PKT|WOL_CTL_DIS_MAGIC_PKT_UNIT;;
769
770 ctrl |= WOL_CTL_DIS_PME_ON_PATTERN|WOL_CTL_DIS_PATTERN_UNIT;
771 sky2_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), ctrl);
772
773 /* Turn on legacy PCI-Express PME mode */
774 reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
775 reg1 |= PCI_Y2_PME_LEGACY;
776 sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
777
778 /* block receiver */
779 sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
780
781 }
782
783 static void sky2_set_tx_stfwd(struct sky2_hw *hw, unsigned port)
784 {
785 struct net_device *dev = hw->dev[port];
786
787 if ( (hw->chip_id == CHIP_ID_YUKON_EX &&
788 hw->chip_rev != CHIP_REV_YU_EX_A0) ||
789 hw->chip_id == CHIP_ID_YUKON_FE_P ||
790 hw->chip_id == CHIP_ID_YUKON_SUPR) {
791 /* Yukon-Extreme B0 and further Extreme devices */
792 /* enable Store & Forward mode for TX */
793
794 if (dev->mtu <= ETH_DATA_LEN)
795 sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T),
796 TX_JUMBO_DIS | TX_STFW_ENA);
797
798 else
799 sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T),
800 TX_JUMBO_ENA| TX_STFW_ENA);
801 } else {
802 if (dev->mtu <= ETH_DATA_LEN)
803 sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_STFW_ENA);
804 else {
805 /* set Tx GMAC FIFO Almost Empty Threshold */
806 sky2_write32(hw, SK_REG(port, TX_GMF_AE_THR),
807 (ECU_JUMBO_WM << 16) | ECU_AE_THR);
808
809 sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_STFW_DIS);
810
811 /* Can't do offload because of lack of store/forward */
812 dev->features &= ~(NETIF_F_TSO | NETIF_F_SG | NETIF_F_ALL_CSUM);
813 }
814 }
815 }
816
817 static void sky2_mac_init(struct sky2_hw *hw, unsigned port)
818 {
819 struct sky2_port *sky2 = netdev_priv(hw->dev[port]);
820 u16 reg;
821 u32 rx_reg;
822 int i;
823 const u8 *addr = hw->dev[port]->dev_addr;
824
825 sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
826 sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR);
827
828 sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR);
829
830 if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0 && port == 1) {
831 /* WA DEV_472 -- looks like crossed wires on port 2 */
832 /* clear GMAC 1 Control reset */
833 sky2_write8(hw, SK_REG(0, GMAC_CTRL), GMC_RST_CLR);
834 do {
835 sky2_write8(hw, SK_REG(1, GMAC_CTRL), GMC_RST_SET);
836 sky2_write8(hw, SK_REG(1, GMAC_CTRL), GMC_RST_CLR);
837 } while (gm_phy_read(hw, 1, PHY_MARV_ID0) != PHY_MARV_ID0_VAL ||
838 gm_phy_read(hw, 1, PHY_MARV_ID1) != PHY_MARV_ID1_Y2 ||
839 gm_phy_read(hw, 1, PHY_MARV_INT_MASK) != 0);
840 }
841
842 sky2_read16(hw, SK_REG(port, GMAC_IRQ_SRC));
843
844 /* Enable Transmit FIFO Underrun */
845 sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), GMAC_DEF_MSK);
846
847 spin_lock_bh(&sky2->phy_lock);
848 sky2_phy_power_up(hw, port);
849 sky2_phy_init(hw, port);
850 spin_unlock_bh(&sky2->phy_lock);
851
852 /* MIB clear */
853 reg = gma_read16(hw, port, GM_PHY_ADDR);
854 gma_write16(hw, port, GM_PHY_ADDR, reg | GM_PAR_MIB_CLR);
855
856 for (i = GM_MIB_CNT_BASE; i <= GM_MIB_CNT_END; i += 4)
857 gma_read16(hw, port, i);
858 gma_write16(hw, port, GM_PHY_ADDR, reg);
859
860 /* transmit control */
861 gma_write16(hw, port, GM_TX_CTRL, TX_COL_THR(TX_COL_DEF));
862
863 /* receive control reg: unicast + multicast + no FCS */
864 gma_write16(hw, port, GM_RX_CTRL,
865 GM_RXCR_UCF_ENA | GM_RXCR_CRC_DIS | GM_RXCR_MCF_ENA);
866
867 /* transmit flow control */
868 gma_write16(hw, port, GM_TX_FLOW_CTRL, 0xffff);
869
870 /* transmit parameter */
871 gma_write16(hw, port, GM_TX_PARAM,
872 TX_JAM_LEN_VAL(TX_JAM_LEN_DEF) |
873 TX_JAM_IPG_VAL(TX_JAM_IPG_DEF) |
874 TX_IPG_JAM_DATA(TX_IPG_JAM_DEF) |
875 TX_BACK_OFF_LIM(TX_BOF_LIM_DEF));
876
877 /* serial mode register */
878 reg = DATA_BLIND_VAL(DATA_BLIND_DEF) |
879 GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF);
880
881 if (hw->dev[port]->mtu > ETH_DATA_LEN)
882 reg |= GM_SMOD_JUMBO_ENA;
883
884 gma_write16(hw, port, GM_SERIAL_MODE, reg);
885
886 /* virtual address for data */
887 gma_set_addr(hw, port, GM_SRC_ADDR_2L, addr);
888
889 /* physical address: used for pause frames */
890 gma_set_addr(hw, port, GM_SRC_ADDR_1L, addr);
891
892 /* ignore counter overflows */
893 gma_write16(hw, port, GM_TX_IRQ_MSK, 0);
894 gma_write16(hw, port, GM_RX_IRQ_MSK, 0);
895 gma_write16(hw, port, GM_TR_IRQ_MSK, 0);
896
897 /* Configure Rx MAC FIFO */
898 sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR);
899 rx_reg = GMF_OPER_ON | GMF_RX_F_FL_ON;
900 if (hw->chip_id == CHIP_ID_YUKON_EX ||
901 hw->chip_id == CHIP_ID_YUKON_FE_P)
902 rx_reg |= GMF_RX_OVER_ON;
903
904 sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), rx_reg);
905
906 if (hw->chip_id == CHIP_ID_YUKON_XL) {
907 /* Hardware errata - clear flush mask */
908 sky2_write16(hw, SK_REG(port, RX_GMF_FL_MSK), 0);
909 } else {
910 /* Flush Rx MAC FIFO on any flow control or error */
911 sky2_write16(hw, SK_REG(port, RX_GMF_FL_MSK), GMR_FS_ANY_ERR);
912 }
913
914 /* Set threshold to 0xa (64 bytes) + 1 to workaround pause bug */
915 reg = RX_GMF_FL_THR_DEF + 1;
916 /* Another magic mystery workaround from sk98lin */
917 if (hw->chip_id == CHIP_ID_YUKON_FE_P &&
918 hw->chip_rev == CHIP_REV_YU_FE2_A0)
919 reg = 0x178;
920 sky2_write16(hw, SK_REG(port, RX_GMF_FL_THR), reg);
921
922 /* Configure Tx MAC FIFO */
923 sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR);
924 sky2_write16(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_OPER_ON);
925
926 /* On chips without ram buffer, pause is controled by MAC level */
927 if (!(hw->flags & SKY2_HW_RAM_BUFFER)) {
928 sky2_write8(hw, SK_REG(port, RX_GMF_LP_THR), 768/8);
929 sky2_write8(hw, SK_REG(port, RX_GMF_UP_THR), 1024/8);
930
931 sky2_set_tx_stfwd(hw, port);
932 }
933
934 if (hw->chip_id == CHIP_ID_YUKON_FE_P &&
935 hw->chip_rev == CHIP_REV_YU_FE2_A0) {
936 /* disable dynamic watermark */
937 reg = sky2_read16(hw, SK_REG(port, TX_GMF_EA));
938 reg &= ~TX_DYN_WM_ENA;
939 sky2_write16(hw, SK_REG(port, TX_GMF_EA), reg);
940 }
941 }
942
943 /* Assign Ram Buffer allocation to queue */
944 static void sky2_ramset(struct sky2_hw *hw, u16 q, u32 start, u32 space)
945 {
946 u32 end;
947
948 /* convert from K bytes to qwords used for hw register */
949 start *= 1024/8;
950 space *= 1024/8;
951 end = start + space - 1;
952
953 sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_RST_CLR);
954 sky2_write32(hw, RB_ADDR(q, RB_START), start);
955 sky2_write32(hw, RB_ADDR(q, RB_END), end);
956 sky2_write32(hw, RB_ADDR(q, RB_WP), start);
957 sky2_write32(hw, RB_ADDR(q, RB_RP), start);
958
959 if (q == Q_R1 || q == Q_R2) {
960 u32 tp = space - space/4;
961
962 /* On receive queue's set the thresholds
963 * give receiver priority when > 3/4 full
964 * send pause when down to 2K
965 */
966 sky2_write32(hw, RB_ADDR(q, RB_RX_UTHP), tp);
967 sky2_write32(hw, RB_ADDR(q, RB_RX_LTHP), space/2);
968
969 tp = space - 2048/8;
970 sky2_write32(hw, RB_ADDR(q, RB_RX_UTPP), tp);
971 sky2_write32(hw, RB_ADDR(q, RB_RX_LTPP), space/4);
972 } else {
973 /* Enable store & forward on Tx queue's because
974 * Tx FIFO is only 1K on Yukon
975 */
976 sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_STFWD);
977 }
978
979 sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_OP_MD);
980 sky2_read8(hw, RB_ADDR(q, RB_CTRL));
981 }
982
983 /* Setup Bus Memory Interface */
984 static void sky2_qset(struct sky2_hw *hw, u16 q)
985 {
986 sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_CLR_RESET);
987 sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_OPER_INIT);
988 sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_FIFO_OP_ON);
989 sky2_write32(hw, Q_ADDR(q, Q_WM), BMU_WM_DEFAULT);
990 }
991
992 /* Setup prefetch unit registers. This is the interface between
993 * hardware and driver list elements
994 */
995 static void sky2_prefetch_init(struct sky2_hw *hw, u32 qaddr,
996 dma_addr_t addr, u32 last)
997 {
998 sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_RST_SET);
999 sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_RST_CLR);
1000 sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_ADDR_HI), upper_32_bits(addr));
1001 sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_ADDR_LO), lower_32_bits(addr));
1002 sky2_write16(hw, Y2_QADDR(qaddr, PREF_UNIT_LAST_IDX), last);
1003 sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_OP_ON);
1004
1005 sky2_read32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL));
1006 }
1007
1008 static inline struct sky2_tx_le *get_tx_le(struct sky2_port *sky2, u16 *slot)
1009 {
1010 struct sky2_tx_le *le = sky2->tx_le + *slot;
1011 struct tx_ring_info *re = sky2->tx_ring + *slot;
1012
1013 *slot = RING_NEXT(*slot, sky2->tx_ring_size);
1014 re->flags = 0;
1015 re->skb = NULL;
1016 le->ctrl = 0;
1017 return le;
1018 }
1019
1020 static void tx_init(struct sky2_port *sky2)
1021 {
1022 struct sky2_tx_le *le;
1023
1024 sky2->tx_prod = sky2->tx_cons = 0;
1025 sky2->tx_tcpsum = 0;
1026 sky2->tx_last_mss = 0;
1027
1028 le = get_tx_le(sky2, &sky2->tx_prod);
1029 le->addr = 0;
1030 le->opcode = OP_ADDR64 | HW_OWNER;
1031 sky2->tx_last_upper = 0;
1032 }
1033
1034 /* Update chip's next pointer */
1035 static inline void sky2_put_idx(struct sky2_hw *hw, unsigned q, u16 idx)
1036 {
1037 /* Make sure write' to descriptors are complete before we tell hardware */
1038 wmb();
1039 sky2_write16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX), idx);
1040
1041 /* Synchronize I/O on since next processor may write to tail */
1042 mmiowb();
1043 }
1044
1045
1046 static inline struct sky2_rx_le *sky2_next_rx(struct sky2_port *sky2)
1047 {
1048 struct sky2_rx_le *le = sky2->rx_le + sky2->rx_put;
1049 sky2->rx_put = RING_NEXT(sky2->rx_put, RX_LE_SIZE);
1050 le->ctrl = 0;
1051 return le;
1052 }
1053
1054 /* Build description to hardware for one receive segment */
1055 static void sky2_rx_add(struct sky2_port *sky2, u8 op,
1056 dma_addr_t map, unsigned len)
1057 {
1058 struct sky2_rx_le *le;
1059
1060 if (sizeof(dma_addr_t) > sizeof(u32)) {
1061 le = sky2_next_rx(sky2);
1062 le->addr = cpu_to_le32(upper_32_bits(map));
1063 le->opcode = OP_ADDR64 | HW_OWNER;
1064 }
1065
1066 le = sky2_next_rx(sky2);
1067 le->addr = cpu_to_le32(lower_32_bits(map));
1068 le->length = cpu_to_le16(len);
1069 le->opcode = op | HW_OWNER;
1070 }
1071
1072 /* Build description to hardware for one possibly fragmented skb */
1073 static void sky2_rx_submit(struct sky2_port *sky2,
1074 const struct rx_ring_info *re)
1075 {
1076 int i;
1077
1078 sky2_rx_add(sky2, OP_PACKET, re->data_addr, sky2->rx_data_size);
1079
1080 for (i = 0; i < skb_shinfo(re->skb)->nr_frags; i++)
1081 sky2_rx_add(sky2, OP_BUFFER, re->frag_addr[i], PAGE_SIZE);
1082 }
1083
1084
1085 static int sky2_rx_map_skb(struct pci_dev *pdev, struct rx_ring_info *re,
1086 unsigned size)
1087 {
1088 struct sk_buff *skb = re->skb;
1089 int i;
1090
1091 re->data_addr = pci_map_single(pdev, skb->data, size, PCI_DMA_FROMDEVICE);
1092 if (unlikely(pci_dma_mapping_error(pdev, re->data_addr)))
1093 return -EIO;
1094
1095 pci_unmap_len_set(re, data_size, size);
1096
1097 for (i = 0; i < skb_shinfo(skb)->nr_frags; i++)
1098 re->frag_addr[i] = pci_map_page(pdev,
1099 skb_shinfo(skb)->frags[i].page,
1100 skb_shinfo(skb)->frags[i].page_offset,
1101 skb_shinfo(skb)->frags[i].size,
1102 PCI_DMA_FROMDEVICE);
1103 return 0;
1104 }
1105
1106 static void sky2_rx_unmap_skb(struct pci_dev *pdev, struct rx_ring_info *re)
1107 {
1108 struct sk_buff *skb = re->skb;
1109 int i;
1110
1111 pci_unmap_single(pdev, re->data_addr, pci_unmap_len(re, data_size),
1112 PCI_DMA_FROMDEVICE);
1113
1114 for (i = 0; i < skb_shinfo(skb)->nr_frags; i++)
1115 pci_unmap_page(pdev, re->frag_addr[i],
1116 skb_shinfo(skb)->frags[i].size,
1117 PCI_DMA_FROMDEVICE);
1118 }
1119
1120 /* Tell chip where to start receive checksum.
1121 * Actually has two checksums, but set both same to avoid possible byte
1122 * order problems.
1123 */
1124 static void rx_set_checksum(struct sky2_port *sky2)
1125 {
1126 struct sky2_rx_le *le = sky2_next_rx(sky2);
1127
1128 le->addr = cpu_to_le32((ETH_HLEN << 16) | ETH_HLEN);
1129 le->ctrl = 0;
1130 le->opcode = OP_TCPSTART | HW_OWNER;
1131
1132 sky2_write32(sky2->hw,
1133 Q_ADDR(rxqaddr[sky2->port], Q_CSR),
1134 (sky2->flags & SKY2_FLAG_RX_CHECKSUM)
1135 ? BMU_ENA_RX_CHKSUM : BMU_DIS_RX_CHKSUM);
1136 }
1137
1138 /*
1139 * The RX Stop command will not work for Yukon-2 if the BMU does not
1140 * reach the end of packet and since we can't make sure that we have
1141 * incoming data, we must reset the BMU while it is not doing a DMA
1142 * transfer. Since it is possible that the RX path is still active,
1143 * the RX RAM buffer will be stopped first, so any possible incoming
1144 * data will not trigger a DMA. After the RAM buffer is stopped, the
1145 * BMU is polled until any DMA in progress is ended and only then it
1146 * will be reset.
1147 */
1148 static void sky2_rx_stop(struct sky2_port *sky2)
1149 {
1150 struct sky2_hw *hw = sky2->hw;
1151 unsigned rxq = rxqaddr[sky2->port];
1152 int i;
1153
1154 /* disable the RAM Buffer receive queue */
1155 sky2_write8(hw, RB_ADDR(rxq, RB_CTRL), RB_DIS_OP_MD);
1156
1157 for (i = 0; i < 0xffff; i++)
1158 if (sky2_read8(hw, RB_ADDR(rxq, Q_RSL))
1159 == sky2_read8(hw, RB_ADDR(rxq, Q_RL)))
1160 goto stopped;
1161
1162 printk(KERN_WARNING PFX "%s: receiver stop failed\n",
1163 sky2->netdev->name);
1164 stopped:
1165 sky2_write32(hw, Q_ADDR(rxq, Q_CSR), BMU_RST_SET | BMU_FIFO_RST);
1166
1167 /* reset the Rx prefetch unit */
1168 sky2_write32(hw, Y2_QADDR(rxq, PREF_UNIT_CTRL), PREF_UNIT_RST_SET);
1169 mmiowb();
1170 }
1171
1172 /* Clean out receive buffer area, assumes receiver hardware stopped */
1173 static void sky2_rx_clean(struct sky2_port *sky2)
1174 {
1175 unsigned i;
1176
1177 memset(sky2->rx_le, 0, RX_LE_BYTES);
1178 for (i = 0; i < sky2->rx_pending; i++) {
1179 struct rx_ring_info *re = sky2->rx_ring + i;
1180
1181 if (re->skb) {
1182 sky2_rx_unmap_skb(sky2->hw->pdev, re);
1183 kfree_skb(re->skb);
1184 re->skb = NULL;
1185 }
1186 }
1187 }
1188
1189 /* Basic MII support */
1190 static int sky2_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
1191 {
1192 struct mii_ioctl_data *data = if_mii(ifr);
1193 struct sky2_port *sky2 = netdev_priv(dev);
1194 struct sky2_hw *hw = sky2->hw;
1195 int err = -EOPNOTSUPP;
1196
1197 if (!netif_running(dev))
1198 return -ENODEV; /* Phy still in reset */
1199
1200 switch (cmd) {
1201 case SIOCGMIIPHY:
1202 data->phy_id = PHY_ADDR_MARV;
1203
1204 /* fallthru */
1205 case SIOCGMIIREG: {
1206 u16 val = 0;
1207
1208 spin_lock_bh(&sky2->phy_lock);
1209 err = __gm_phy_read(hw, sky2->port, data->reg_num & 0x1f, &val);
1210 spin_unlock_bh(&sky2->phy_lock);
1211
1212 data->val_out = val;
1213 break;
1214 }
1215
1216 case SIOCSMIIREG:
1217 spin_lock_bh(&sky2->phy_lock);
1218 err = gm_phy_write(hw, sky2->port, data->reg_num & 0x1f,
1219 data->val_in);
1220 spin_unlock_bh(&sky2->phy_lock);
1221 break;
1222 }
1223 return err;
1224 }
1225
1226 #ifdef SKY2_VLAN_TAG_USED
1227 static void sky2_set_vlan_mode(struct sky2_hw *hw, u16 port, bool onoff)
1228 {
1229 if (onoff) {
1230 sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T),
1231 RX_VLAN_STRIP_ON);
1232 sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T),
1233 TX_VLAN_TAG_ON);
1234 } else {
1235 sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T),
1236 RX_VLAN_STRIP_OFF);
1237 sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T),
1238 TX_VLAN_TAG_OFF);
1239 }
1240 }
1241
1242 static void sky2_vlan_rx_register(struct net_device *dev, struct vlan_group *grp)
1243 {
1244 struct sky2_port *sky2 = netdev_priv(dev);
1245 struct sky2_hw *hw = sky2->hw;
1246 u16 port = sky2->port;
1247
1248 netif_tx_lock_bh(dev);
1249 napi_disable(&hw->napi);
1250
1251 sky2->vlgrp = grp;
1252 sky2_set_vlan_mode(hw, port, grp != NULL);
1253
1254 sky2_read32(hw, B0_Y2_SP_LISR);
1255 napi_enable(&hw->napi);
1256 netif_tx_unlock_bh(dev);
1257 }
1258 #endif
1259
1260 /* Amount of required worst case padding in rx buffer */
1261 static inline unsigned sky2_rx_pad(const struct sky2_hw *hw)
1262 {
1263 return (hw->flags & SKY2_HW_RAM_BUFFER) ? 8 : 2;
1264 }
1265
1266 /*
1267 * Allocate an skb for receiving. If the MTU is large enough
1268 * make the skb non-linear with a fragment list of pages.
1269 */
1270 static struct sk_buff *sky2_rx_alloc(struct sky2_port *sky2)
1271 {
1272 struct sk_buff *skb;
1273 int i;
1274
1275 skb = netdev_alloc_skb(sky2->netdev,
1276 sky2->rx_data_size + sky2_rx_pad(sky2->hw));
1277 if (!skb)
1278 goto nomem;
1279
1280 if (sky2->hw->flags & SKY2_HW_RAM_BUFFER) {
1281 unsigned char *start;
1282 /*
1283 * Workaround for a bug in FIFO that cause hang
1284 * if the FIFO if the receive buffer is not 64 byte aligned.
1285 * The buffer returned from netdev_alloc_skb is
1286 * aligned except if slab debugging is enabled.
1287 */
1288 start = PTR_ALIGN(skb->data, 8);
1289 skb_reserve(skb, start - skb->data);
1290 } else
1291 skb_reserve(skb, NET_IP_ALIGN);
1292
1293 for (i = 0; i < sky2->rx_nfrags; i++) {
1294 struct page *page = alloc_page(GFP_ATOMIC);
1295
1296 if (!page)
1297 goto free_partial;
1298 skb_fill_page_desc(skb, i, page, 0, PAGE_SIZE);
1299 }
1300
1301 return skb;
1302 free_partial:
1303 kfree_skb(skb);
1304 nomem:
1305 return NULL;
1306 }
1307
1308 static inline void sky2_rx_update(struct sky2_port *sky2, unsigned rxq)
1309 {
1310 sky2_put_idx(sky2->hw, rxq, sky2->rx_put);
1311 }
1312
1313 /*
1314 * Allocate and setup receiver buffer pool.
1315 * Normal case this ends up creating one list element for skb
1316 * in the receive ring. Worst case if using large MTU and each
1317 * allocation falls on a different 64 bit region, that results
1318 * in 6 list elements per ring entry.
1319 * One element is used for checksum enable/disable, and one
1320 * extra to avoid wrap.
1321 */
1322 static int sky2_rx_start(struct sky2_port *sky2)
1323 {
1324 struct sky2_hw *hw = sky2->hw;
1325 struct rx_ring_info *re;
1326 unsigned rxq = rxqaddr[sky2->port];
1327 unsigned i, size, thresh;
1328
1329 sky2->rx_put = sky2->rx_next = 0;
1330 sky2_qset(hw, rxq);
1331
1332 /* On PCI express lowering the watermark gives better performance */
1333 if (pci_find_capability(hw->pdev, PCI_CAP_ID_EXP))
1334 sky2_write32(hw, Q_ADDR(rxq, Q_WM), BMU_WM_PEX);
1335
1336 /* These chips have no ram buffer?
1337 * MAC Rx RAM Read is controlled by hardware */
1338 if (hw->chip_id == CHIP_ID_YUKON_EC_U &&
1339 (hw->chip_rev == CHIP_REV_YU_EC_U_A1
1340 || hw->chip_rev == CHIP_REV_YU_EC_U_B0))
1341 sky2_write32(hw, Q_ADDR(rxq, Q_TEST), F_M_RX_RAM_DIS);
1342
1343 sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1);
1344
1345 if (!(hw->flags & SKY2_HW_NEW_LE))
1346 rx_set_checksum(sky2);
1347
1348 /* Space needed for frame data + headers rounded up */
1349 size = roundup(sky2->netdev->mtu + ETH_HLEN + VLAN_HLEN, 8);
1350
1351 /* Stopping point for hardware truncation */
1352 thresh = (size - 8) / sizeof(u32);
1353
1354 sky2->rx_nfrags = size >> PAGE_SHIFT;
1355 BUG_ON(sky2->rx_nfrags > ARRAY_SIZE(re->frag_addr));
1356
1357 /* Compute residue after pages */
1358 size -= sky2->rx_nfrags << PAGE_SHIFT;
1359
1360 /* Optimize to handle small packets and headers */
1361 if (size < copybreak)
1362 size = copybreak;
1363 if (size < ETH_HLEN)
1364 size = ETH_HLEN;
1365
1366 sky2->rx_data_size = size;
1367
1368 /* Fill Rx ring */
1369 for (i = 0; i < sky2->rx_pending; i++) {
1370 re = sky2->rx_ring + i;
1371
1372 re->skb = sky2_rx_alloc(sky2);
1373 if (!re->skb)
1374 goto nomem;
1375
1376 if (sky2_rx_map_skb(hw->pdev, re, sky2->rx_data_size)) {
1377 dev_kfree_skb(re->skb);
1378 re->skb = NULL;
1379 goto nomem;
1380 }
1381
1382 sky2_rx_submit(sky2, re);
1383 }
1384
1385 /*
1386 * The receiver hangs if it receives frames larger than the
1387 * packet buffer. As a workaround, truncate oversize frames, but
1388 * the register is limited to 9 bits, so if you do frames > 2052
1389 * you better get the MTU right!
1390 */
1391 if (thresh > 0x1ff)
1392 sky2_write32(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), RX_TRUNC_OFF);
1393 else {
1394 sky2_write16(hw, SK_REG(sky2->port, RX_GMF_TR_THR), thresh);
1395 sky2_write32(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), RX_TRUNC_ON);
1396 }
1397
1398 /* Tell chip about available buffers */
1399 sky2_rx_update(sky2, rxq);
1400 return 0;
1401 nomem:
1402 sky2_rx_clean(sky2);
1403 return -ENOMEM;
1404 }
1405
1406 static int sky2_alloc_buffers(struct sky2_port *sky2)
1407 {
1408 struct sky2_hw *hw = sky2->hw;
1409
1410 /* must be power of 2 */
1411 sky2->tx_le = pci_alloc_consistent(hw->pdev,
1412 sky2->tx_ring_size *
1413 sizeof(struct sky2_tx_le),
1414 &sky2->tx_le_map);
1415 if (!sky2->tx_le)
1416 goto nomem;
1417
1418 sky2->tx_ring = kcalloc(sky2->tx_ring_size, sizeof(struct tx_ring_info),
1419 GFP_KERNEL);
1420 if (!sky2->tx_ring)
1421 goto nomem;
1422
1423 sky2->rx_le = pci_alloc_consistent(hw->pdev, RX_LE_BYTES,
1424 &sky2->rx_le_map);
1425 if (!sky2->rx_le)
1426 goto nomem;
1427 memset(sky2->rx_le, 0, RX_LE_BYTES);
1428
1429 sky2->rx_ring = kcalloc(sky2->rx_pending, sizeof(struct rx_ring_info),
1430 GFP_KERNEL);
1431 if (!sky2->rx_ring)
1432 goto nomem;
1433
1434 return 0;
1435 nomem:
1436 return -ENOMEM;
1437 }
1438
1439 static void sky2_free_buffers(struct sky2_port *sky2)
1440 {
1441 struct sky2_hw *hw = sky2->hw;
1442
1443 if (sky2->rx_le) {
1444 pci_free_consistent(hw->pdev, RX_LE_BYTES,
1445 sky2->rx_le, sky2->rx_le_map);
1446 sky2->rx_le = NULL;
1447 }
1448 if (sky2->tx_le) {
1449 pci_free_consistent(hw->pdev,
1450 sky2->tx_ring_size * sizeof(struct sky2_tx_le),
1451 sky2->tx_le, sky2->tx_le_map);
1452 sky2->tx_le = NULL;
1453 }
1454 kfree(sky2->tx_ring);
1455 kfree(sky2->rx_ring);
1456
1457 sky2->tx_ring = NULL;
1458 sky2->rx_ring = NULL;
1459 }
1460
1461 /* Bring up network interface. */
1462 static int sky2_up(struct net_device *dev)
1463 {
1464 struct sky2_port *sky2 = netdev_priv(dev);
1465 struct sky2_hw *hw = sky2->hw;
1466 unsigned port = sky2->port;
1467 u32 imask, ramsize;
1468 int cap, err;
1469 struct net_device *otherdev = hw->dev[sky2->port^1];
1470
1471 /*
1472 * On dual port PCI-X card, there is an problem where status
1473 * can be received out of order due to split transactions
1474 */
1475 if (otherdev && netif_running(otherdev) &&
1476 (cap = pci_find_capability(hw->pdev, PCI_CAP_ID_PCIX))) {
1477 u16 cmd;
1478
1479 cmd = sky2_pci_read16(hw, cap + PCI_X_CMD);
1480 cmd &= ~PCI_X_CMD_MAX_SPLIT;
1481 sky2_pci_write16(hw, cap + PCI_X_CMD, cmd);
1482
1483 }
1484
1485 netif_carrier_off(dev);
1486
1487 err = sky2_alloc_buffers(sky2);
1488 if (err)
1489 goto err_out;
1490
1491 tx_init(sky2);
1492
1493 sky2_mac_init(hw, port);
1494
1495 /* Register is number of 4K blocks on internal RAM buffer. */
1496 ramsize = sky2_read8(hw, B2_E_0) * 4;
1497 if (ramsize > 0) {
1498 u32 rxspace;
1499
1500 hw->flags |= SKY2_HW_RAM_BUFFER;
1501 pr_debug(PFX "%s: ram buffer %dK\n", dev->name, ramsize);
1502 if (ramsize < 16)
1503 rxspace = ramsize / 2;
1504 else
1505 rxspace = 8 + (2*(ramsize - 16))/3;
1506
1507 sky2_ramset(hw, rxqaddr[port], 0, rxspace);
1508 sky2_ramset(hw, txqaddr[port], rxspace, ramsize - rxspace);
1509
1510 /* Make sure SyncQ is disabled */
1511 sky2_write8(hw, RB_ADDR(port == 0 ? Q_XS1 : Q_XS2, RB_CTRL),
1512 RB_RST_SET);
1513 }
1514
1515 sky2_qset(hw, txqaddr[port]);
1516
1517 /* This is copied from sk98lin 10.0.5.3; no one tells me about erratta's */
1518 if (hw->chip_id == CHIP_ID_YUKON_EX && hw->chip_rev == CHIP_REV_YU_EX_B0)
1519 sky2_write32(hw, Q_ADDR(txqaddr[port], Q_TEST), F_TX_CHK_AUTO_OFF);
1520
1521 /* Set almost empty threshold */
1522 if (hw->chip_id == CHIP_ID_YUKON_EC_U
1523 && hw->chip_rev == CHIP_REV_YU_EC_U_A0)
1524 sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), ECU_TXFF_LEV);
1525
1526 sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map,
1527 sky2->tx_ring_size - 1);
1528
1529 #ifdef SKY2_VLAN_TAG_USED
1530 sky2_set_vlan_mode(hw, port, sky2->vlgrp != NULL);
1531 #endif
1532
1533 err = sky2_rx_start(sky2);
1534 if (err)
1535 goto err_out;
1536
1537 /* Enable interrupts from phy/mac for port */
1538 imask = sky2_read32(hw, B0_IMSK);
1539 imask |= portirq_msk[port];
1540 sky2_write32(hw, B0_IMSK, imask);
1541 sky2_read32(hw, B0_IMSK);
1542
1543 if (netif_msg_ifup(sky2))
1544 printk(KERN_INFO PFX "%s: enabling interface\n", dev->name);
1545
1546 return 0;
1547
1548 err_out:
1549 sky2_free_buffers(sky2);
1550 return err;
1551 }
1552
1553 /* Modular subtraction in ring */
1554 static inline int tx_inuse(const struct sky2_port *sky2)
1555 {
1556 return (sky2->tx_prod - sky2->tx_cons) & (sky2->tx_ring_size - 1);
1557 }
1558
1559 /* Number of list elements available for next tx */
1560 static inline int tx_avail(const struct sky2_port *sky2)
1561 {
1562 return sky2->tx_pending - tx_inuse(sky2);
1563 }
1564
1565 /* Estimate of number of transmit list elements required */
1566 static unsigned tx_le_req(const struct sk_buff *skb)
1567 {
1568 unsigned count;
1569
1570 count = sizeof(dma_addr_t) / sizeof(u32);
1571 count += skb_shinfo(skb)->nr_frags * count;
1572
1573 if (skb_is_gso(skb))
1574 ++count;
1575
1576 if (skb->ip_summed == CHECKSUM_PARTIAL)
1577 ++count;
1578
1579 return count;
1580 }
1581
1582 static void sky2_tx_unmap(struct pci_dev *pdev,
1583 const struct tx_ring_info *re)
1584 {
1585 if (re->flags & TX_MAP_SINGLE)
1586 pci_unmap_single(pdev, pci_unmap_addr(re, mapaddr),
1587 pci_unmap_len(re, maplen),
1588 PCI_DMA_TODEVICE);
1589 else if (re->flags & TX_MAP_PAGE)
1590 pci_unmap_page(pdev, pci_unmap_addr(re, mapaddr),
1591 pci_unmap_len(re, maplen),
1592 PCI_DMA_TODEVICE);
1593 }
1594
1595 /*
1596 * Put one packet in ring for transmit.
1597 * A single packet can generate multiple list elements, and
1598 * the number of ring elements will probably be less than the number
1599 * of list elements used.
1600 */
1601 static netdev_tx_t sky2_xmit_frame(struct sk_buff *skb,
1602 struct net_device *dev)
1603 {
1604 struct sky2_port *sky2 = netdev_priv(dev);
1605 struct sky2_hw *hw = sky2->hw;
1606 struct sky2_tx_le *le = NULL;
1607 struct tx_ring_info *re;
1608 unsigned i, len;
1609 dma_addr_t mapping;
1610 u32 upper;
1611 u16 slot;
1612 u16 mss;
1613 u8 ctrl;
1614
1615 if (unlikely(tx_avail(sky2) < tx_le_req(skb)))
1616 return NETDEV_TX_BUSY;
1617
1618 len = skb_headlen(skb);
1619 mapping = pci_map_single(hw->pdev, skb->data, len, PCI_DMA_TODEVICE);
1620
1621 if (pci_dma_mapping_error(hw->pdev, mapping))
1622 goto mapping_error;
1623
1624 slot = sky2->tx_prod;
1625 if (unlikely(netif_msg_tx_queued(sky2)))
1626 printk(KERN_DEBUG "%s: tx queued, slot %u, len %d\n",
1627 dev->name, slot, skb->len);
1628
1629 /* Send high bits if needed */
1630 upper = upper_32_bits(mapping);
1631 if (upper != sky2->tx_last_upper) {
1632 le = get_tx_le(sky2, &slot);
1633 le->addr = cpu_to_le32(upper);
1634 sky2->tx_last_upper = upper;
1635 le->opcode = OP_ADDR64 | HW_OWNER;
1636 }
1637
1638 /* Check for TCP Segmentation Offload */
1639 mss = skb_shinfo(skb)->gso_size;
1640 if (mss != 0) {
1641
1642 if (!(hw->flags & SKY2_HW_NEW_LE))
1643 mss += ETH_HLEN + ip_hdrlen(skb) + tcp_hdrlen(skb);
1644
1645 if (mss != sky2->tx_last_mss) {
1646 le = get_tx_le(sky2, &slot);
1647 le->addr = cpu_to_le32(mss);
1648
1649 if (hw->flags & SKY2_HW_NEW_LE)
1650 le->opcode = OP_MSS | HW_OWNER;
1651 else
1652 le->opcode = OP_LRGLEN | HW_OWNER;
1653 sky2->tx_last_mss = mss;
1654 }
1655 }
1656
1657 ctrl = 0;
1658 #ifdef SKY2_VLAN_TAG_USED
1659 /* Add VLAN tag, can piggyback on LRGLEN or ADDR64 */
1660 if (sky2->vlgrp && vlan_tx_tag_present(skb)) {
1661 if (!le) {
1662 le = get_tx_le(sky2, &slot);
1663 le->addr = 0;
1664 le->opcode = OP_VLAN|HW_OWNER;
1665 } else
1666 le->opcode |= OP_VLAN;
1667 le->length = cpu_to_be16(vlan_tx_tag_get(skb));
1668 ctrl |= INS_VLAN;
1669 }
1670 #endif
1671
1672 /* Handle TCP checksum offload */
1673 if (skb->ip_summed == CHECKSUM_PARTIAL) {
1674 /* On Yukon EX (some versions) encoding change. */
1675 if (hw->flags & SKY2_HW_AUTO_TX_SUM)
1676 ctrl |= CALSUM; /* auto checksum */
1677 else {
1678 const unsigned offset = skb_transport_offset(skb);
1679 u32 tcpsum;
1680
1681 tcpsum = offset << 16; /* sum start */
1682 tcpsum |= offset + skb->csum_offset; /* sum write */
1683
1684 ctrl |= CALSUM | WR_SUM | INIT_SUM | LOCK_SUM;
1685 if (ip_hdr(skb)->protocol == IPPROTO_UDP)
1686 ctrl |= UDPTCP;
1687
1688 if (tcpsum != sky2->tx_tcpsum) {
1689 sky2->tx_tcpsum = tcpsum;
1690
1691 le = get_tx_le(sky2, &slot);
1692 le->addr = cpu_to_le32(tcpsum);
1693 le->length = 0; /* initial checksum value */
1694 le->ctrl = 1; /* one packet */
1695 le->opcode = OP_TCPLISW | HW_OWNER;
1696 }
1697 }
1698 }
1699
1700 re = sky2->tx_ring + slot;
1701 re->flags = TX_MAP_SINGLE;
1702 pci_unmap_addr_set(re, mapaddr, mapping);
1703 pci_unmap_len_set(re, maplen, len);
1704
1705 le = get_tx_le(sky2, &slot);
1706 le->addr = cpu_to_le32(lower_32_bits(mapping));
1707 le->length = cpu_to_le16(len);
1708 le->ctrl = ctrl;
1709 le->opcode = mss ? (OP_LARGESEND | HW_OWNER) : (OP_PACKET | HW_OWNER);
1710
1711
1712 for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
1713 const skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
1714
1715 mapping = pci_map_page(hw->pdev, frag->page, frag->page_offset,
1716 frag->size, PCI_DMA_TODEVICE);
1717
1718 if (pci_dma_mapping_error(hw->pdev, mapping))
1719 goto mapping_unwind;
1720
1721 upper = upper_32_bits(mapping);
1722 if (upper != sky2->tx_last_upper) {
1723 le = get_tx_le(sky2, &slot);
1724 le->addr = cpu_to_le32(upper);
1725 sky2->tx_last_upper = upper;
1726 le->opcode = OP_ADDR64 | HW_OWNER;
1727 }
1728
1729 re = sky2->tx_ring + slot;
1730 re->flags = TX_MAP_PAGE;
1731 pci_unmap_addr_set(re, mapaddr, mapping);
1732 pci_unmap_len_set(re, maplen, frag->size);
1733
1734 le = get_tx_le(sky2, &slot);
1735 le->addr = cpu_to_le32(lower_32_bits(mapping));
1736 le->length = cpu_to_le16(frag->size);
1737 le->ctrl = ctrl;
1738 le->opcode = OP_BUFFER | HW_OWNER;
1739 }
1740
1741 re->skb = skb;
1742 le->ctrl |= EOP;
1743
1744 sky2->tx_prod = slot;
1745
1746 if (tx_avail(sky2) <= MAX_SKB_TX_LE)
1747 netif_stop_queue(dev);
1748
1749 sky2_put_idx(hw, txqaddr[sky2->port], sky2->tx_prod);
1750
1751 return NETDEV_TX_OK;
1752
1753 mapping_unwind:
1754 for (i = sky2->tx_prod; i != slot; i = RING_NEXT(i, sky2->tx_ring_size)) {
1755 re = sky2->tx_ring + i;
1756
1757 sky2_tx_unmap(hw->pdev, re);
1758 }
1759
1760 mapping_error:
1761 if (net_ratelimit())
1762 dev_warn(&hw->pdev->dev, "%s: tx mapping error\n", dev->name);
1763 dev_kfree_skb(skb);
1764 return NETDEV_TX_OK;
1765 }
1766
1767 /*
1768 * Free ring elements from starting at tx_cons until "done"
1769 *
1770 * NB:
1771 * 1. The hardware will tell us about partial completion of multi-part
1772 * buffers so make sure not to free skb to early.
1773 * 2. This may run in parallel start_xmit because the it only
1774 * looks at the tail of the queue of FIFO (tx_cons), not
1775 * the head (tx_prod)
1776 */
1777 static void sky2_tx_complete(struct sky2_port *sky2, u16 done)
1778 {
1779 struct net_device *dev = sky2->netdev;
1780 unsigned idx;
1781
1782 BUG_ON(done >= sky2->tx_ring_size);
1783
1784 for (idx = sky2->tx_cons; idx != done;
1785 idx = RING_NEXT(idx, sky2->tx_ring_size)) {
1786 struct tx_ring_info *re = sky2->tx_ring + idx;
1787 struct sk_buff *skb = re->skb;
1788
1789 sky2_tx_unmap(sky2->hw->pdev, re);
1790
1791 if (skb) {
1792 if (unlikely(netif_msg_tx_done(sky2)))
1793 printk(KERN_DEBUG "%s: tx done %u\n",
1794 dev->name, idx);
1795
1796 dev->stats.tx_packets++;
1797 dev->stats.tx_bytes += skb->len;
1798
1799 dev_kfree_skb_any(skb);
1800
1801 sky2->tx_next = RING_NEXT(idx, sky2->tx_ring_size);
1802 }
1803 }
1804
1805 sky2->tx_cons = idx;
1806 smp_mb();
1807
1808 if (tx_avail(sky2) > MAX_SKB_TX_LE + 4)
1809 netif_wake_queue(dev);
1810 }
1811
1812 static void sky2_tx_reset(struct sky2_hw *hw, unsigned port)
1813 {
1814 /* Disable Force Sync bit and Enable Alloc bit */
1815 sky2_write8(hw, SK_REG(port, TXA_CTRL),
1816 TXA_DIS_FSYNC | TXA_DIS_ALLOC | TXA_STOP_RC);
1817
1818 /* Stop Interval Timer and Limit Counter of Tx Arbiter */
1819 sky2_write32(hw, SK_REG(port, TXA_ITI_INI), 0L);
1820 sky2_write32(hw, SK_REG(port, TXA_LIM_INI), 0L);
1821
1822 /* Reset the PCI FIFO of the async Tx queue */
1823 sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR),
1824 BMU_RST_SET | BMU_FIFO_RST);
1825
1826 /* Reset the Tx prefetch units */
1827 sky2_write32(hw, Y2_QADDR(txqaddr[port], PREF_UNIT_CTRL),
1828 PREF_UNIT_RST_SET);
1829
1830 sky2_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL), RB_RST_SET);
1831 sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_SET);
1832 }
1833
1834 /* Network shutdown */
1835 static int sky2_down(struct net_device *dev)
1836 {
1837 struct sky2_port *sky2 = netdev_priv(dev);
1838 struct sky2_hw *hw = sky2->hw;
1839 unsigned port = sky2->port;
1840 u16 ctrl;
1841 u32 imask;
1842
1843 /* Never really got started! */
1844 if (!sky2->tx_le)
1845 return 0;
1846
1847 if (netif_msg_ifdown(sky2))
1848 printk(KERN_INFO PFX "%s: disabling interface\n", dev->name);
1849
1850 /* Force flow control off */
1851 sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
1852
1853 /* Stop transmitter */
1854 sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), BMU_STOP);
1855 sky2_read32(hw, Q_ADDR(txqaddr[port], Q_CSR));
1856
1857 sky2_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL),
1858 RB_RST_SET | RB_DIS_OP_MD);
1859
1860 ctrl = gma_read16(hw, port, GM_GP_CTRL);
1861 ctrl &= ~(GM_GPCR_TX_ENA | GM_GPCR_RX_ENA);
1862 gma_write16(hw, port, GM_GP_CTRL, ctrl);
1863
1864 sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
1865
1866 /* Workaround shared GMAC reset */
1867 if (!(hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0
1868 && port == 0 && hw->dev[1] && netif_running(hw->dev[1])))
1869 sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_SET);
1870
1871 sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
1872
1873 /* Force any delayed status interrrupt and NAPI */
1874 sky2_write32(hw, STAT_LEV_TIMER_CNT, 0);
1875 sky2_write32(hw, STAT_TX_TIMER_CNT, 0);
1876 sky2_write32(hw, STAT_ISR_TIMER_CNT, 0);
1877 sky2_read8(hw, STAT_ISR_TIMER_CTRL);
1878
1879 sky2_rx_stop(sky2);
1880
1881 /* Disable port IRQ */
1882 imask = sky2_read32(hw, B0_IMSK);
1883 imask &= ~portirq_msk[port];
1884 sky2_write32(hw, B0_IMSK, imask);
1885 sky2_read32(hw, B0_IMSK);
1886
1887 synchronize_irq(hw->pdev->irq);
1888 napi_synchronize(&hw->napi);
1889
1890 spin_lock_bh(&sky2->phy_lock);
1891 sky2_phy_power_down(hw, port);
1892 spin_unlock_bh(&sky2->phy_lock);
1893
1894 sky2_tx_reset(hw, port);
1895
1896 /* Free any pending frames stuck in HW queue */
1897 sky2_tx_complete(sky2, sky2->tx_prod);
1898
1899 sky2_rx_clean(sky2);
1900
1901 sky2_free_buffers(sky2);
1902
1903 return 0;
1904 }
1905
1906 static u16 sky2_phy_speed(const struct sky2_hw *hw, u16 aux)
1907 {
1908 if (hw->flags & SKY2_HW_FIBRE_PHY)
1909 return SPEED_1000;
1910
1911 if (!(hw->flags & SKY2_HW_GIGABIT)) {
1912 if (aux & PHY_M_PS_SPEED_100)
1913 return SPEED_100;
1914 else
1915 return SPEED_10;
1916 }
1917
1918 switch (aux & PHY_M_PS_SPEED_MSK) {
1919 case PHY_M_PS_SPEED_1000:
1920 return SPEED_1000;
1921 case PHY_M_PS_SPEED_100:
1922 return SPEED_100;
1923 default:
1924 return SPEED_10;
1925 }
1926 }
1927
1928 static void sky2_link_up(struct sky2_port *sky2)
1929 {
1930 struct sky2_hw *hw = sky2->hw;
1931 unsigned port = sky2->port;
1932 u16 reg;
1933 static const char *fc_name[] = {
1934 [FC_NONE] = "none",
1935 [FC_TX] = "tx",
1936 [FC_RX] = "rx",
1937 [FC_BOTH] = "both",
1938 };
1939
1940 /* enable Rx/Tx */
1941 reg = gma_read16(hw, port, GM_GP_CTRL);
1942 reg |= GM_GPCR_RX_ENA | GM_GPCR_TX_ENA;
1943 gma_write16(hw, port, GM_GP_CTRL, reg);
1944
1945 gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
1946
1947 netif_carrier_on(sky2->netdev);
1948
1949 mod_timer(&hw->watchdog_timer, jiffies + 1);
1950
1951 /* Turn on link LED */
1952 sky2_write8(hw, SK_REG(port, LNK_LED_REG),
1953 LINKLED_ON | LINKLED_BLINK_OFF | LINKLED_LINKSYNC_OFF);
1954
1955 if (netif_msg_link(sky2))
1956 printk(KERN_INFO PFX
1957 "%s: Link is up at %d Mbps, %s duplex, flow control %s\n",
1958 sky2->netdev->name, sky2->speed,
1959 sky2->duplex == DUPLEX_FULL ? "full" : "half",
1960 fc_name[sky2->flow_status]);
1961 }
1962
1963 static void sky2_link_down(struct sky2_port *sky2)
1964 {
1965 struct sky2_hw *hw = sky2->hw;
1966 unsigned port = sky2->port;
1967 u16 reg;
1968
1969 gm_phy_write(hw, port, PHY_MARV_INT_MASK, 0);
1970
1971 reg = gma_read16(hw, port, GM_GP_CTRL);
1972 reg &= ~(GM_GPCR_RX_ENA | GM_GPCR_TX_ENA);
1973 gma_write16(hw, port, GM_GP_CTRL, reg);
1974
1975 netif_carrier_off(sky2->netdev);
1976
1977 /* Turn on link LED */
1978 sky2_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF);
1979
1980 if (netif_msg_link(sky2))
1981 printk(KERN_INFO PFX "%s: Link is down.\n", sky2->netdev->name);
1982
1983 sky2_phy_init(hw, port);
1984 }
1985
1986 static enum flow_control sky2_flow(int rx, int tx)
1987 {
1988 if (rx)
1989 return tx ? FC_BOTH : FC_RX;
1990 else
1991 return tx ? FC_TX : FC_NONE;
1992 }
1993
1994 static int sky2_autoneg_done(struct sky2_port *sky2, u16 aux)
1995 {
1996 struct sky2_hw *hw = sky2->hw;
1997 unsigned port = sky2->port;
1998 u16 advert, lpa;
1999
2000 advert = gm_phy_read(hw, port, PHY_MARV_AUNE_ADV);
2001 lpa = gm_phy_read(hw, port, PHY_MARV_AUNE_LP);
2002 if (lpa & PHY_M_AN_RF) {
2003 printk(KERN_ERR PFX "%s: remote fault", sky2->netdev->name);
2004 return -1;
2005 }
2006
2007 if (!(aux & PHY_M_PS_SPDUP_RES)) {
2008 printk(KERN_ERR PFX "%s: speed/duplex mismatch",
2009 sky2->netdev->name);
2010 return -1;
2011 }
2012
2013 sky2->speed = sky2_phy_speed(hw, aux);
2014 sky2->duplex = (aux & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF;
2015
2016 /* Since the pause result bits seem to in different positions on
2017 * different chips. look at registers.
2018 */
2019 if (hw->flags & SKY2_HW_FIBRE_PHY) {
2020 /* Shift for bits in fiber PHY */
2021 advert &= ~(ADVERTISE_PAUSE_CAP|ADVERTISE_PAUSE_ASYM);
2022 lpa &= ~(LPA_PAUSE_CAP|LPA_PAUSE_ASYM);
2023
2024 if (advert & ADVERTISE_1000XPAUSE)
2025 advert |= ADVERTISE_PAUSE_CAP;
2026 if (advert & ADVERTISE_1000XPSE_ASYM)
2027 advert |= ADVERTISE_PAUSE_ASYM;
2028 if (lpa & LPA_1000XPAUSE)
2029 lpa |= LPA_PAUSE_CAP;
2030 if (lpa & LPA_1000XPAUSE_ASYM)
2031 lpa |= LPA_PAUSE_ASYM;
2032 }
2033
2034 sky2->flow_status = FC_NONE;
2035 if (advert & ADVERTISE_PAUSE_CAP) {
2036 if (lpa & LPA_PAUSE_CAP)
2037 sky2->flow_status = FC_BOTH;
2038 else if (advert & ADVERTISE_PAUSE_ASYM)
2039 sky2->flow_status = FC_RX;
2040 } else if (advert & ADVERTISE_PAUSE_ASYM) {
2041 if ((lpa & LPA_PAUSE_CAP) && (lpa & LPA_PAUSE_ASYM))
2042 sky2->flow_status = FC_TX;
2043 }
2044
2045 if (sky2->duplex == DUPLEX_HALF && sky2->speed < SPEED_1000
2046 && !(hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX))
2047 sky2->flow_status = FC_NONE;
2048
2049 if (sky2->flow_status & FC_TX)
2050 sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON);
2051 else
2052 sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
2053
2054 return 0;
2055 }
2056
2057 /* Interrupt from PHY */
2058 static void sky2_phy_intr(struct sky2_hw *hw, unsigned port)
2059 {
2060 struct net_device *dev = hw->dev[port];
2061 struct sky2_port *sky2 = netdev_priv(dev);
2062 u16 istatus, phystat;
2063
2064 if (!netif_running(dev))
2065 return;
2066
2067 spin_lock(&sky2->phy_lock);
2068 istatus = gm_phy_read(hw, port, PHY_MARV_INT_STAT);
2069 phystat = gm_phy_read(hw, port, PHY_MARV_PHY_STAT);
2070
2071 if (netif_msg_intr(sky2))
2072 printk(KERN_INFO PFX "%s: phy interrupt status 0x%x 0x%x\n",
2073 sky2->netdev->name, istatus, phystat);
2074
2075 if (istatus & PHY_M_IS_AN_COMPL) {
2076 if (sky2_autoneg_done(sky2, phystat) == 0)
2077 sky2_link_up(sky2);
2078 goto out;
2079 }
2080
2081 if (istatus & PHY_M_IS_LSP_CHANGE)
2082 sky2->speed = sky2_phy_speed(hw, phystat);
2083
2084 if (istatus & PHY_M_IS_DUP_CHANGE)
2085 sky2->duplex =
2086 (phystat & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF;
2087
2088 if (istatus & PHY_M_IS_LST_CHANGE) {
2089 if (phystat & PHY_M_PS_LINK_UP)
2090 sky2_link_up(sky2);
2091 else
2092 sky2_link_down(sky2);
2093 }
2094 out:
2095 spin_unlock(&sky2->phy_lock);
2096 }
2097
2098 /* Transmit timeout is only called if we are running, carrier is up
2099 * and tx queue is full (stopped).
2100 */
2101 static void sky2_tx_timeout(struct net_device *dev)
2102 {
2103 struct sky2_port *sky2 = netdev_priv(dev);
2104 struct sky2_hw *hw = sky2->hw;
2105
2106 if (netif_msg_timer(sky2))
2107 printk(KERN_ERR PFX "%s: tx timeout\n", dev->name);
2108
2109 printk(KERN_DEBUG PFX "%s: transmit ring %u .. %u report=%u done=%u\n",
2110 dev->name, sky2->tx_cons, sky2->tx_prod,
2111 sky2_read16(hw, sky2->port == 0 ? STAT_TXA1_RIDX : STAT_TXA2_RIDX),
2112 sky2_read16(hw, Q_ADDR(txqaddr[sky2->port], Q_DONE)));
2113
2114 /* can't restart safely under softirq */
2115 schedule_work(&hw->restart_work);
2116 }
2117
2118 static int sky2_change_mtu(struct net_device *dev, int new_mtu)
2119 {
2120 struct sky2_port *sky2 = netdev_priv(dev);
2121 struct sky2_hw *hw = sky2->hw;
2122 unsigned port = sky2->port;
2123 int err;
2124 u16 ctl, mode;
2125 u32 imask;
2126
2127 if (new_mtu < ETH_ZLEN || new_mtu > ETH_JUMBO_MTU)
2128 return -EINVAL;
2129
2130 if (new_mtu > ETH_DATA_LEN &&
2131 (hw->chip_id == CHIP_ID_YUKON_FE ||
2132 hw->chip_id == CHIP_ID_YUKON_FE_P))
2133 return -EINVAL;
2134
2135 if (!netif_running(dev)) {
2136 dev->mtu = new_mtu;
2137 return 0;
2138 }
2139
2140 imask = sky2_read32(hw, B0_IMSK);
2141 sky2_write32(hw, B0_IMSK, 0);
2142
2143 dev->trans_start = jiffies; /* prevent tx timeout */
2144 netif_stop_queue(dev);
2145 napi_disable(&hw->napi);
2146
2147 synchronize_irq(hw->pdev->irq);
2148
2149 if (!(hw->flags & SKY2_HW_RAM_BUFFER))
2150 sky2_set_tx_stfwd(hw, port);
2151
2152 ctl = gma_read16(hw, port, GM_GP_CTRL);
2153 gma_write16(hw, port, GM_GP_CTRL, ctl & ~GM_GPCR_RX_ENA);
2154 sky2_rx_stop(sky2);
2155 sky2_rx_clean(sky2);
2156
2157 dev->mtu = new_mtu;
2158
2159 mode = DATA_BLIND_VAL(DATA_BLIND_DEF) |
2160 GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF);
2161
2162 if (dev->mtu > ETH_DATA_LEN)
2163 mode |= GM_SMOD_JUMBO_ENA;
2164
2165 gma_write16(hw, port, GM_SERIAL_MODE, mode);
2166
2167 sky2_write8(hw, RB_ADDR(rxqaddr[port], RB_CTRL), RB_ENA_OP_MD);
2168
2169 err = sky2_rx_start(sky2);
2170 sky2_write32(hw, B0_IMSK, imask);
2171
2172 sky2_read32(hw, B0_Y2_SP_LISR);
2173 napi_enable(&hw->napi);
2174
2175 if (err)
2176 dev_close(dev);
2177 else {
2178 gma_write16(hw, port, GM_GP_CTRL, ctl);
2179
2180 netif_wake_queue(dev);
2181 }
2182
2183 return err;
2184 }
2185
2186 /* For small just reuse existing skb for next receive */
2187 static struct sk_buff *receive_copy(struct sky2_port *sky2,
2188 const struct rx_ring_info *re,
2189 unsigned length)
2190 {
2191 struct sk_buff *skb;
2192
2193 skb = netdev_alloc_skb(sky2->netdev, length + 2);
2194 if (likely(skb)) {
2195 skb_reserve(skb, 2);
2196 pci_dma_sync_single_for_cpu(sky2->hw->pdev, re->data_addr,
2197 length, PCI_DMA_FROMDEVICE);
2198 skb_copy_from_linear_data(re->skb, skb->data, length);
2199 skb->ip_summed = re->skb->ip_summed;
2200 skb->csum = re->skb->csum;
2201 pci_dma_sync_single_for_device(sky2->hw->pdev, re->data_addr,
2202 length, PCI_DMA_FROMDEVICE);
2203 re->skb->ip_summed = CHECKSUM_NONE;
2204 skb_put(skb, length);
2205 }
2206 return skb;
2207 }
2208
2209 /* Adjust length of skb with fragments to match received data */
2210 static void skb_put_frags(struct sk_buff *skb, unsigned int hdr_space,
2211 unsigned int length)
2212 {
2213 int i, num_frags;
2214 unsigned int size;
2215
2216 /* put header into skb */
2217 size = min(length, hdr_space);
2218 skb->tail += size;
2219 skb->len += size;
2220 length -= size;
2221
2222 num_frags = skb_shinfo(skb)->nr_frags;
2223 for (i = 0; i < num_frags; i++) {
2224 skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
2225
2226 if (length == 0) {
2227 /* don't need this page */
2228 __free_page(frag->page);
2229 --skb_shinfo(skb)->nr_frags;
2230 } else {
2231 size = min(length, (unsigned) PAGE_SIZE);
2232
2233 frag->size = size;
2234 skb->data_len += size;
2235 skb->truesize += size;
2236 skb->len += size;
2237 length -= size;
2238 }
2239 }
2240 }
2241
2242 /* Normal packet - take skb from ring element and put in a new one */
2243 static struct sk_buff *receive_new(struct sky2_port *sky2,
2244 struct rx_ring_info *re,
2245 unsigned int length)
2246 {
2247 struct sk_buff *skb, *nskb;
2248 unsigned hdr_space = sky2->rx_data_size;
2249
2250 /* Don't be tricky about reusing pages (yet) */
2251 nskb = sky2_rx_alloc(sky2);
2252 if (unlikely(!nskb))
2253 return NULL;
2254
2255 skb = re->skb;
2256 sky2_rx_unmap_skb(sky2->hw->pdev, re);
2257
2258 prefetch(skb->data);
2259 re->skb = nskb;
2260 if (sky2_rx_map_skb(sky2->hw->pdev, re, hdr_space)) {
2261 dev_kfree_skb(nskb);
2262 re->skb = skb;
2263 return NULL;
2264 }
2265
2266 if (skb_shinfo(skb)->nr_frags)
2267 skb_put_frags(skb, hdr_space, length);
2268 else
2269 skb_put(skb, length);
2270 return skb;
2271 }
2272
2273 /*
2274 * Receive one packet.
2275 * For larger packets, get new buffer.
2276 */
2277 static struct sk_buff *sky2_receive(struct net_device *dev,
2278 u16 length, u32 status)
2279 {
2280 struct sky2_port *sky2 = netdev_priv(dev);
2281 struct rx_ring_info *re = sky2->rx_ring + sky2->rx_next;
2282 struct sk_buff *skb = NULL;
2283 u16 count = (status & GMR_FS_LEN) >> 16;
2284
2285 #ifdef SKY2_VLAN_TAG_USED
2286 /* Account for vlan tag */
2287 if (sky2->vlgrp && (status & GMR_FS_VLAN))
2288 count -= VLAN_HLEN;
2289 #endif
2290
2291 if (unlikely(netif_msg_rx_status(sky2)))
2292 printk(KERN_DEBUG PFX "%s: rx slot %u status 0x%x len %d\n",
2293 dev->name, sky2->rx_next, status, length);
2294
2295 sky2->rx_next = (sky2->rx_next + 1) % sky2->rx_pending;
2296 prefetch(sky2->rx_ring + sky2->rx_next);
2297
2298 /* This chip has hardware problems that generates bogus status.
2299 * So do only marginal checking and expect higher level protocols
2300 * to handle crap frames.
2301 */
2302 if (sky2->hw->chip_id == CHIP_ID_YUKON_FE_P &&
2303 sky2->hw->chip_rev == CHIP_REV_YU_FE2_A0 &&
2304 length != count)
2305 goto okay;
2306
2307 if (status & GMR_FS_ANY_ERR)
2308 goto error;
2309
2310 if (!(status & GMR_FS_RX_OK))
2311 goto resubmit;
2312
2313 /* if length reported by DMA does not match PHY, packet was truncated */
2314 if (length != count)
2315 goto len_error;
2316
2317 okay:
2318 if (length < copybreak)
2319 skb = receive_copy(sky2, re, length);
2320 else
2321 skb = receive_new(sky2, re, length);
2322 resubmit:
2323 sky2_rx_submit(sky2, re);
2324
2325 return skb;
2326
2327 len_error:
2328 /* Truncation of overlength packets
2329 causes PHY length to not match MAC length */
2330 ++dev->stats.rx_length_errors;
2331 if (netif_msg_rx_err(sky2) && net_ratelimit())
2332 pr_info(PFX "%s: rx length error: status %#x length %d\n",
2333 dev->name, status, length);
2334 goto resubmit;
2335
2336 error:
2337 ++dev->stats.rx_errors;
2338 if (status & GMR_FS_RX_FF_OV) {
2339 dev->stats.rx_over_errors++;
2340 goto resubmit;
2341 }
2342
2343 if (netif_msg_rx_err(sky2) && net_ratelimit())
2344 printk(KERN_INFO PFX "%s: rx error, status 0x%x length %d\n",
2345 dev->name, status, length);
2346
2347 if (status & (GMR_FS_LONG_ERR | GMR_FS_UN_SIZE))
2348 dev->stats.rx_length_errors++;
2349 if (status & GMR_FS_FRAGMENT)
2350 dev->stats.rx_frame_errors++;
2351 if (status & GMR_FS_CRC_ERR)
2352 dev->stats.rx_crc_errors++;
2353
2354 goto resubmit;
2355 }
2356
2357 /* Transmit complete */
2358 static inline void sky2_tx_done(struct net_device *dev, u16 last)
2359 {
2360 struct sky2_port *sky2 = netdev_priv(dev);
2361
2362 if (netif_running(dev))
2363 sky2_tx_complete(sky2, last);
2364 }
2365
2366 static inline void sky2_skb_rx(const struct sky2_port *sky2,
2367 u32 status, struct sk_buff *skb)
2368 {
2369 #ifdef SKY2_VLAN_TAG_USED
2370 u16 vlan_tag = be16_to_cpu(sky2->rx_tag);
2371 if (sky2->vlgrp && (status & GMR_FS_VLAN)) {
2372 if (skb->ip_summed == CHECKSUM_NONE)
2373 vlan_hwaccel_receive_skb(skb, sky2->vlgrp, vlan_tag);
2374 else
2375 vlan_gro_receive(&sky2->hw->napi, sky2->vlgrp,
2376 vlan_tag, skb);
2377 return;
2378 }
2379 #endif
2380 if (skb->ip_summed == CHECKSUM_NONE)
2381 netif_receive_skb(skb);
2382 else
2383 napi_gro_receive(&sky2->hw->napi, skb);
2384 }
2385
2386 static inline void sky2_rx_done(struct sky2_hw *hw, unsigned port,
2387 unsigned packets, unsigned bytes)
2388 {
2389 if (packets) {
2390 struct net_device *dev = hw->dev[port];
2391
2392 dev->stats.rx_packets += packets;
2393 dev->stats.rx_bytes += bytes;
2394 dev->last_rx = jiffies;
2395 sky2_rx_update(netdev_priv(dev), rxqaddr[port]);
2396 }
2397 }
2398
2399 /* Process status response ring */
2400 static int sky2_status_intr(struct sky2_hw *hw, int to_do, u16 idx)
2401 {
2402 int work_done = 0;
2403 unsigned int total_bytes[2] = { 0 };
2404 unsigned int total_packets[2] = { 0 };
2405
2406 rmb();
2407 do {
2408 struct sky2_port *sky2;
2409 struct sky2_status_le *le = hw->st_le + hw->st_idx;
2410 unsigned port;
2411 struct net_device *dev;
2412 struct sk_buff *skb;
2413 u32 status;
2414 u16 length;
2415 u8 opcode = le->opcode;
2416
2417 if (!(opcode & HW_OWNER))
2418 break;
2419
2420 hw->st_idx = RING_NEXT(hw->st_idx, STATUS_RING_SIZE);
2421
2422 port = le->css & CSS_LINK_BIT;
2423 dev = hw->dev[port];
2424 sky2 = netdev_priv(dev);
2425 length = le16_to_cpu(le->length);
2426 status = le32_to_cpu(le->status);
2427
2428 le->opcode = 0;
2429 switch (opcode & ~HW_OWNER) {
2430 case OP_RXSTAT:
2431 total_packets[port]++;
2432 total_bytes[port] += length;
2433 skb = sky2_receive(dev, length, status);
2434 if (unlikely(!skb)) {
2435 dev->stats.rx_dropped++;
2436 break;
2437 }
2438
2439 /* This chip reports checksum status differently */
2440 if (hw->flags & SKY2_HW_NEW_LE) {
2441 if ((sky2->flags & SKY2_FLAG_RX_CHECKSUM) &&
2442 (le->css & (CSS_ISIPV4 | CSS_ISIPV6)) &&
2443 (le->css & CSS_TCPUDPCSOK))
2444 skb->ip_summed = CHECKSUM_UNNECESSARY;
2445 else
2446 skb->ip_summed = CHECKSUM_NONE;
2447 }
2448
2449 skb->protocol = eth_type_trans(skb, dev);
2450
2451 sky2_skb_rx(sky2, status, skb);
2452
2453 /* Stop after net poll weight */
2454 if (++work_done >= to_do)
2455 goto exit_loop;
2456 break;
2457
2458 #ifdef SKY2_VLAN_TAG_USED
2459 case OP_RXVLAN:
2460 sky2->rx_tag = length;
2461 break;
2462
2463 case OP_RXCHKSVLAN:
2464 sky2->rx_tag = length;
2465 /* fall through */
2466 #endif
2467 case OP_RXCHKS:
2468 if (!(sky2->flags & SKY2_FLAG_RX_CHECKSUM))
2469 break;
2470
2471 /* If this happens then driver assuming wrong format */
2472 if (unlikely(hw->flags & SKY2_HW_NEW_LE)) {
2473 if (net_ratelimit())
2474 printk(KERN_NOTICE "%s: unexpected"
2475 " checksum status\n",
2476 dev->name);
2477 break;
2478 }
2479
2480 /* Both checksum counters are programmed to start at
2481 * the same offset, so unless there is a problem they
2482 * should match. This failure is an early indication that
2483 * hardware receive checksumming won't work.
2484 */
2485 if (likely(status >> 16 == (status & 0xffff))) {
2486 skb = sky2->rx_ring[sky2->rx_next].skb;
2487 skb->ip_summed = CHECKSUM_COMPLETE;
2488 skb->csum = le16_to_cpu(status);
2489 } else {
2490 printk(KERN_NOTICE PFX "%s: hardware receive "
2491 "checksum problem (status = %#x)\n",
2492 dev->name, status);
2493 sky2->flags &= ~SKY2_FLAG_RX_CHECKSUM;
2494
2495 sky2_write32(sky2->hw,
2496 Q_ADDR(rxqaddr[port], Q_CSR),
2497 BMU_DIS_RX_CHKSUM);
2498 }
2499 break;
2500
2501 case OP_TXINDEXLE:
2502 /* TX index reports status for both ports */
2503 sky2_tx_done(hw->dev[0], status & 0xfff);
2504 if (hw->dev[1])
2505 sky2_tx_done(hw->dev[1],
2506 ((status >> 24) & 0xff)
2507 | (u16)(length & 0xf) << 8);
2508 break;
2509
2510 default:
2511 if (net_ratelimit())
2512 printk(KERN_WARNING PFX
2513 "unknown status opcode 0x%x\n", opcode);
2514 }
2515 } while (hw->st_idx != idx);
2516
2517 /* Fully processed status ring so clear irq */
2518 sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ);
2519
2520 exit_loop:
2521 sky2_rx_done(hw, 0, total_packets[0], total_bytes[0]);
2522 sky2_rx_done(hw, 1, total_packets[1], total_bytes[1]);
2523
2524 return work_done;
2525 }
2526
2527 static void sky2_hw_error(struct sky2_hw *hw, unsigned port, u32 status)
2528 {
2529 struct net_device *dev = hw->dev[port];
2530
2531 if (net_ratelimit())
2532 printk(KERN_INFO PFX "%s: hw error interrupt status 0x%x\n",
2533 dev->name, status);
2534
2535 if (status & Y2_IS_PAR_RD1) {
2536 if (net_ratelimit())
2537 printk(KERN_ERR PFX "%s: ram data read parity error\n",
2538 dev->name);
2539 /* Clear IRQ */
2540 sky2_write16(hw, RAM_BUFFER(port, B3_RI_CTRL), RI_CLR_RD_PERR);
2541 }
2542
2543 if (status & Y2_IS_PAR_WR1) {
2544 if (net_ratelimit())
2545 printk(KERN_ERR PFX "%s: ram data write parity error\n",
2546 dev->name);
2547
2548 sky2_write16(hw, RAM_BUFFER(port, B3_RI_CTRL), RI_CLR_WR_PERR);
2549 }
2550
2551 if (status & Y2_IS_PAR_MAC1) {
2552 if (net_ratelimit())
2553 printk(KERN_ERR PFX "%s: MAC parity error\n", dev->name);
2554 sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_PE);
2555 }
2556
2557 if (status & Y2_IS_PAR_RX1) {
2558 if (net_ratelimit())
2559 printk(KERN_ERR PFX "%s: RX parity error\n", dev->name);
2560 sky2_write32(hw, Q_ADDR(rxqaddr[port], Q_CSR), BMU_CLR_IRQ_PAR);
2561 }
2562
2563 if (status & Y2_IS_TCP_TXA1) {
2564 if (net_ratelimit())
2565 printk(KERN_ERR PFX "%s: TCP segmentation error\n",
2566 dev->name);
2567 sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), BMU_CLR_IRQ_TCP);
2568 }
2569 }
2570
2571 static void sky2_hw_intr(struct sky2_hw *hw)
2572 {
2573 struct pci_dev *pdev = hw->pdev;
2574 u32 status = sky2_read32(hw, B0_HWE_ISRC);
2575 u32 hwmsk = sky2_read32(hw, B0_HWE_IMSK);
2576
2577 status &= hwmsk;
2578
2579 if (status & Y2_IS_TIST_OV)
2580 sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ);
2581
2582 if (status & (Y2_IS_MST_ERR | Y2_IS_IRQ_STAT)) {
2583 u16 pci_err;
2584
2585 sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
2586 pci_err = sky2_pci_read16(hw, PCI_STATUS);
2587 if (net_ratelimit())
2588 dev_err(&pdev->dev, "PCI hardware error (0x%x)\n",
2589 pci_err);
2590
2591 sky2_pci_write16(hw, PCI_STATUS,
2592 pci_err | PCI_STATUS_ERROR_BITS);
2593 sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
2594 }
2595
2596 if (status & Y2_IS_PCI_EXP) {
2597 /* PCI-Express uncorrectable Error occurred */
2598 u32 err;
2599
2600 sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
2601 err = sky2_read32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS);
2602 sky2_write32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS,
2603 0xfffffffful);
2604 if (net_ratelimit())
2605 dev_err(&pdev->dev, "PCI Express error (0x%x)\n", err);
2606
2607 sky2_read32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS);
2608 sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
2609 }
2610
2611 if (status & Y2_HWE_L1_MASK)
2612 sky2_hw_error(hw, 0, status);
2613 status >>= 8;
2614 if (status & Y2_HWE_L1_MASK)
2615 sky2_hw_error(hw, 1, status);
2616 }
2617
2618 static void sky2_mac_intr(struct sky2_hw *hw, unsigned port)
2619 {
2620 struct net_device *dev = hw->dev[port];
2621 struct sky2_port *sky2 = netdev_priv(dev);
2622 u8 status = sky2_read8(hw, SK_REG(port, GMAC_IRQ_SRC));
2623
2624 if (netif_msg_intr(sky2))
2625 printk(KERN_INFO PFX "%s: mac interrupt status 0x%x\n",
2626 dev->name, status);
2627
2628 if (status & GM_IS_RX_CO_OV)
2629 gma_read16(hw, port, GM_RX_IRQ_SRC);
2630
2631 if (status & GM_IS_TX_CO_OV)
2632 gma_read16(hw, port, GM_TX_IRQ_SRC);
2633
2634 if (status & GM_IS_RX_FF_OR) {
2635 ++dev->stats.rx_fifo_errors;
2636 sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_CLI_RX_FO);
2637 }
2638
2639 if (status & GM_IS_TX_FF_UR) {
2640 ++dev->stats.tx_fifo_errors;
2641 sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_FU);
2642 }
2643 }
2644
2645 /* This should never happen it is a bug. */
2646 static void sky2_le_error(struct sky2_hw *hw, unsigned port, u16 q)
2647 {
2648 struct net_device *dev = hw->dev[port];
2649 u16 idx = sky2_read16(hw, Y2_QADDR(q, PREF_UNIT_GET_IDX));
2650
2651 dev_err(&hw->pdev->dev, PFX
2652 "%s: descriptor error q=%#x get=%u put=%u\n",
2653 dev->name, (unsigned) q, (unsigned) idx,
2654 (unsigned) sky2_read16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX)));
2655
2656 sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_CLR_IRQ_CHK);
2657 }
2658
2659 static int sky2_rx_hung(struct net_device *dev)
2660 {
2661 struct sky2_port *sky2 = netdev_priv(dev);
2662 struct sky2_hw *hw = sky2->hw;
2663 unsigned port = sky2->port;
2664 unsigned rxq = rxqaddr[port];
2665 u32 mac_rp = sky2_read32(hw, SK_REG(port, RX_GMF_RP));
2666 u8 mac_lev = sky2_read8(hw, SK_REG(port, RX_GMF_RLEV));
2667 u8 fifo_rp = sky2_read8(hw, Q_ADDR(rxq, Q_RP));
2668 u8 fifo_lev = sky2_read8(hw, Q_ADDR(rxq, Q_RL));
2669
2670 /* If idle and MAC or PCI is stuck */
2671 if (sky2->check.last == dev->last_rx &&
2672 ((mac_rp == sky2->check.mac_rp &&
2673 mac_lev != 0 && mac_lev >= sky2->check.mac_lev) ||
2674 /* Check if the PCI RX hang */
2675 (fifo_rp == sky2->check.fifo_rp &&
2676 fifo_lev != 0 && fifo_lev >= sky2->check.fifo_lev))) {
2677 printk(KERN_DEBUG PFX "%s: hung mac %d:%d fifo %d (%d:%d)\n",
2678 dev->name, mac_lev, mac_rp, fifo_lev, fifo_rp,
2679 sky2_read8(hw, Q_ADDR(rxq, Q_WP)));
2680 return 1;
2681 } else {
2682 sky2->check.last = dev->last_rx;
2683 sky2->check.mac_rp = mac_rp;
2684 sky2->check.mac_lev = mac_lev;
2685 sky2->check.fifo_rp = fifo_rp;
2686 sky2->check.fifo_lev = fifo_lev;
2687 return 0;
2688 }
2689 }
2690
2691 static void sky2_watchdog(unsigned long arg)
2692 {
2693 struct sky2_hw *hw = (struct sky2_hw *) arg;
2694
2695 /* Check for lost IRQ once a second */
2696 if (sky2_read32(hw, B0_ISRC)) {
2697 napi_schedule(&hw->napi);
2698 } else {
2699 int i, active = 0;
2700
2701 for (i = 0; i < hw->ports; i++) {
2702 struct net_device *dev = hw->dev[i];
2703 if (!netif_running(dev))
2704 continue;
2705 ++active;
2706
2707 /* For chips with Rx FIFO, check if stuck */
2708 if ((hw->flags & SKY2_HW_RAM_BUFFER) &&
2709 sky2_rx_hung(dev)) {
2710 pr_info(PFX "%s: receiver hang detected\n",
2711 dev->name);
2712 schedule_work(&hw->restart_work);
2713 return;
2714 }
2715 }
2716
2717 if (active == 0)
2718 return;
2719 }
2720
2721 mod_timer(&hw->watchdog_timer, round_jiffies(jiffies + HZ));
2722 }
2723
2724 /* Hardware/software error handling */
2725 static void sky2_err_intr(struct sky2_hw *hw, u32 status)
2726 {
2727 if (net_ratelimit())
2728 dev_warn(&hw->pdev->dev, "error interrupt status=%#x\n", status);
2729
2730 if (status & Y2_IS_HW_ERR)
2731 sky2_hw_intr(hw);
2732
2733 if (status & Y2_IS_IRQ_MAC1)
2734 sky2_mac_intr(hw, 0);
2735
2736 if (status & Y2_IS_IRQ_MAC2)
2737 sky2_mac_intr(hw, 1);
2738
2739 if (status & Y2_IS_CHK_RX1)
2740 sky2_le_error(hw, 0, Q_R1);
2741
2742 if (status & Y2_IS_CHK_RX2)
2743 sky2_le_error(hw, 1, Q_R2);
2744
2745 if (status & Y2_IS_CHK_TXA1)
2746 sky2_le_error(hw, 0, Q_XA1);
2747
2748 if (status & Y2_IS_CHK_TXA2)
2749 sky2_le_error(hw, 1, Q_XA2);
2750 }
2751
2752 static int sky2_poll(struct napi_struct *napi, int work_limit)
2753 {
2754 struct sky2_hw *hw = container_of(napi, struct sky2_hw, napi);
2755 u32 status = sky2_read32(hw, B0_Y2_SP_EISR);
2756 int work_done = 0;
2757 u16 idx;
2758
2759 if (unlikely(status & Y2_IS_ERROR))
2760 sky2_err_intr(hw, status);
2761
2762 if (status & Y2_IS_IRQ_PHY1)
2763 sky2_phy_intr(hw, 0);
2764
2765 if (status & Y2_IS_IRQ_PHY2)
2766 sky2_phy_intr(hw, 1);
2767
2768 while ((idx = sky2_read16(hw, STAT_PUT_IDX)) != hw->st_idx) {
2769 work_done += sky2_status_intr(hw, work_limit - work_done, idx);
2770
2771 if (work_done >= work_limit)
2772 goto done;
2773 }
2774
2775 napi_complete(napi);
2776 sky2_read32(hw, B0_Y2_SP_LISR);
2777 done:
2778
2779 return work_done;
2780 }
2781
2782 static irqreturn_t sky2_intr(int irq, void *dev_id)
2783 {
2784 struct sky2_hw *hw = dev_id;
2785 u32 status;
2786
2787 /* Reading this mask interrupts as side effect */
2788 status = sky2_read32(hw, B0_Y2_SP_ISRC2);
2789 if (status == 0 || status == ~0)
2790 return IRQ_NONE;
2791
2792 prefetch(&hw->st_le[hw->st_idx]);
2793
2794 napi_schedule(&hw->napi);
2795
2796 return IRQ_HANDLED;
2797 }
2798
2799 #ifdef CONFIG_NET_POLL_CONTROLLER
2800 static void sky2_netpoll(struct net_device *dev)
2801 {
2802 struct sky2_port *sky2 = netdev_priv(dev);
2803
2804 napi_schedule(&sky2->hw->napi);
2805 }
2806 #endif
2807
2808 /* Chip internal frequency for clock calculations */
2809 static u32 sky2_mhz(const struct sky2_hw *hw)
2810 {
2811 switch (hw->chip_id) {
2812 case CHIP_ID_YUKON_EC:
2813 case CHIP_ID_YUKON_EC_U:
2814 case CHIP_ID_YUKON_EX:
2815 case CHIP_ID_YUKON_SUPR:
2816 case CHIP_ID_YUKON_UL_2:
2817 return 125;
2818
2819 case CHIP_ID_YUKON_FE:
2820 return 100;
2821
2822 case CHIP_ID_YUKON_FE_P:
2823 return 50;
2824
2825 case CHIP_ID_YUKON_XL:
2826 return 156;
2827
2828 default:
2829 BUG();
2830 }
2831 }
2832
2833 static inline u32 sky2_us2clk(const struct sky2_hw *hw, u32 us)
2834 {
2835 return sky2_mhz(hw) * us;
2836 }
2837
2838 static inline u32 sky2_clk2us(const struct sky2_hw *hw, u32 clk)
2839 {
2840 return clk / sky2_mhz(hw);
2841 }
2842
2843
2844 static int __devinit sky2_init(struct sky2_hw *hw)
2845 {
2846 u8 t8;
2847
2848 /* Enable all clocks and check for bad PCI access */
2849 sky2_pci_write32(hw, PCI_DEV_REG3, 0);
2850
2851 sky2_write8(hw, B0_CTST, CS_RST_CLR);
2852
2853 hw->chip_id = sky2_read8(hw, B2_CHIP_ID);
2854 hw->chip_rev = (sky2_read8(hw, B2_MAC_CFG) & CFG_CHIP_R_MSK) >> 4;
2855
2856 switch(hw->chip_id) {
2857 case CHIP_ID_YUKON_XL:
2858 hw->flags = SKY2_HW_GIGABIT | SKY2_HW_NEWER_PHY;
2859 break;
2860
2861 case CHIP_ID_YUKON_EC_U:
2862 hw->flags = SKY2_HW_GIGABIT
2863 | SKY2_HW_NEWER_PHY
2864 | SKY2_HW_ADV_POWER_CTL;
2865 break;
2866
2867 case CHIP_ID_YUKON_EX:
2868 hw->flags = SKY2_HW_GIGABIT
2869 | SKY2_HW_NEWER_PHY
2870 | SKY2_HW_NEW_LE
2871 | SKY2_HW_ADV_POWER_CTL;
2872
2873 /* New transmit checksum */
2874 if (hw->chip_rev != CHIP_REV_YU_EX_B0)
2875 hw->flags |= SKY2_HW_AUTO_TX_SUM;
2876 break;
2877
2878 case CHIP_ID_YUKON_EC:
2879 /* This rev is really old, and requires untested workarounds */
2880 if (hw->chip_rev == CHIP_REV_YU_EC_A1) {
2881 dev_err(&hw->pdev->dev, "unsupported revision Yukon-EC rev A1\n");
2882 return -EOPNOTSUPP;
2883 }
2884 hw->flags = SKY2_HW_GIGABIT;
2885 break;
2886
2887 case CHIP_ID_YUKON_FE:
2888 break;
2889
2890 case CHIP_ID_YUKON_FE_P:
2891 hw->flags = SKY2_HW_NEWER_PHY
2892 | SKY2_HW_NEW_LE
2893 | SKY2_HW_AUTO_TX_SUM
2894 | SKY2_HW_ADV_POWER_CTL;
2895 break;
2896
2897 case CHIP_ID_YUKON_SUPR:
2898 hw->flags = SKY2_HW_GIGABIT
2899 | SKY2_HW_NEWER_PHY
2900 | SKY2_HW_NEW_LE
2901 | SKY2_HW_AUTO_TX_SUM
2902 | SKY2_HW_ADV_POWER_CTL;
2903 break;
2904
2905 case CHIP_ID_YUKON_UL_2:
2906 hw->flags = SKY2_HW_GIGABIT
2907 | SKY2_HW_ADV_POWER_CTL;
2908 break;
2909
2910 default:
2911 dev_err(&hw->pdev->dev, "unsupported chip type 0x%x\n",
2912 hw->chip_id);
2913 return -EOPNOTSUPP;
2914 }
2915
2916 hw->pmd_type = sky2_read8(hw, B2_PMD_TYP);
2917 if (hw->pmd_type == 'L' || hw->pmd_type == 'S' || hw->pmd_type == 'P')
2918 hw->flags |= SKY2_HW_FIBRE_PHY;
2919
2920 hw->ports = 1;
2921 t8 = sky2_read8(hw, B2_Y2_HW_RES);
2922 if ((t8 & CFG_DUAL_MAC_MSK) == CFG_DUAL_MAC_MSK) {
2923 if (!(sky2_read8(hw, B2_Y2_CLK_GATE) & Y2_STATUS_LNK2_INAC))
2924 ++hw->ports;
2925 }
2926
2927 return 0;
2928 }
2929
2930 static void sky2_reset(struct sky2_hw *hw)
2931 {
2932 struct pci_dev *pdev = hw->pdev;
2933 u16 status;
2934 int i, cap;
2935 u32 hwe_mask = Y2_HWE_ALL_MASK;
2936
2937 /* disable ASF */
2938 if (hw->chip_id == CHIP_ID_YUKON_EX) {
2939 status = sky2_read16(hw, HCU_CCSR);
2940 status &= ~(HCU_CCSR_AHB_RST | HCU_CCSR_CPU_RST_MODE |
2941 HCU_CCSR_UC_STATE_MSK);
2942 sky2_write16(hw, HCU_CCSR, status);
2943 } else
2944 sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET);
2945 sky2_write16(hw, B0_CTST, Y2_ASF_DISABLE);
2946
2947 /* do a SW reset */
2948 sky2_write8(hw, B0_CTST, CS_RST_SET);
2949 sky2_write8(hw, B0_CTST, CS_RST_CLR);
2950
2951 /* allow writes to PCI config */
2952 sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
2953
2954 /* clear PCI errors, if any */
2955 status = sky2_pci_read16(hw, PCI_STATUS);
2956 status |= PCI_STATUS_ERROR_BITS;
2957 sky2_pci_write16(hw, PCI_STATUS, status);
2958
2959 sky2_write8(hw, B0_CTST, CS_MRST_CLR);
2960
2961 cap = pci_find_capability(pdev, PCI_CAP_ID_EXP);
2962 if (cap) {
2963 sky2_write32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS,
2964 0xfffffffful);
2965
2966 /* If error bit is stuck on ignore it */
2967 if (sky2_read32(hw, B0_HWE_ISRC) & Y2_IS_PCI_EXP)
2968 dev_info(&pdev->dev, "ignoring stuck error report bit\n");
2969 else
2970 hwe_mask |= Y2_IS_PCI_EXP;
2971 }
2972
2973 sky2_power_on(hw);
2974 sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
2975
2976 for (i = 0; i < hw->ports; i++) {
2977 sky2_write8(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_SET);
2978 sky2_write8(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_CLR);
2979
2980 if (hw->chip_id == CHIP_ID_YUKON_EX ||
2981 hw->chip_id == CHIP_ID_YUKON_SUPR)
2982 sky2_write16(hw, SK_REG(i, GMAC_CTRL),
2983 GMC_BYP_MACSECRX_ON | GMC_BYP_MACSECTX_ON
2984 | GMC_BYP_RETR_ON);
2985 }
2986
2987 /* Clear I2C IRQ noise */
2988 sky2_write32(hw, B2_I2C_IRQ, 1);
2989
2990 /* turn off hardware timer (unused) */
2991 sky2_write8(hw, B2_TI_CTRL, TIM_STOP);
2992 sky2_write8(hw, B2_TI_CTRL, TIM_CLR_IRQ);
2993
2994 /* Turn off descriptor polling */
2995 sky2_write32(hw, B28_DPT_CTRL, DPT_STOP);
2996
2997 /* Turn off receive timestamp */
2998 sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_STOP);
2999 sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ);
3000
3001 /* enable the Tx Arbiters */
3002 for (i = 0; i < hw->ports; i++)
3003 sky2_write8(hw, SK_REG(i, TXA_CTRL), TXA_ENA_ARB);
3004
3005 /* Initialize ram interface */
3006 for (i = 0; i < hw->ports; i++) {
3007 sky2_write8(hw, RAM_BUFFER(i, B3_RI_CTRL), RI_RST_CLR);
3008
3009 sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_R1), SK_RI_TO_53);
3010 sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XA1), SK_RI_TO_53);
3011 sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XS1), SK_RI_TO_53);
3012 sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_R1), SK_RI_TO_53);
3013 sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XA1), SK_RI_TO_53);
3014 sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XS1), SK_RI_TO_53);
3015 sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_R2), SK_RI_TO_53);
3016 sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XA2), SK_RI_TO_53);
3017 sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XS2), SK_RI_TO_53);
3018 sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_R2), SK_RI_TO_53);
3019 sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XA2), SK_RI_TO_53);
3020 sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XS2), SK_RI_TO_53);
3021 }
3022
3023 sky2_write32(hw, B0_HWE_IMSK, hwe_mask);
3024
3025 for (i = 0; i < hw->ports; i++)
3026 sky2_gmac_reset(hw, i);
3027
3028 memset(hw->st_le, 0, STATUS_LE_BYTES);
3029 hw->st_idx = 0;
3030
3031 sky2_write32(hw, STAT_CTRL, SC_STAT_RST_SET);
3032 sky2_write32(hw, STAT_CTRL, SC_STAT_RST_CLR);
3033
3034 sky2_write32(hw, STAT_LIST_ADDR_LO, hw->st_dma);
3035 sky2_write32(hw, STAT_LIST_ADDR_HI, (u64) hw->st_dma >> 32);
3036
3037 /* Set the list last index */
3038 sky2_write16(hw, STAT_LAST_IDX, STATUS_RING_SIZE - 1);
3039
3040 sky2_write16(hw, STAT_TX_IDX_TH, 10);
3041 sky2_write8(hw, STAT_FIFO_WM, 16);
3042
3043 /* set Status-FIFO ISR watermark */
3044 if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0)
3045 sky2_write8(hw, STAT_FIFO_ISR_WM, 4);
3046 else
3047 sky2_write8(hw, STAT_FIFO_ISR_WM, 16);
3048
3049 sky2_write32(hw, STAT_TX_TIMER_INI, sky2_us2clk(hw, 1000));
3050 sky2_write32(hw, STAT_ISR_TIMER_INI, sky2_us2clk(hw, 20));
3051 sky2_write32(hw, STAT_LEV_TIMER_INI, sky2_us2clk(hw, 100));
3052
3053 /* enable status unit */
3054 sky2_write32(hw, STAT_CTRL, SC_STAT_OP_ON);
3055
3056 sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
3057 sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_START);
3058 sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START);
3059 }
3060
3061 /* Take device down (offline).
3062 * Equivalent to doing dev_stop() but this does not
3063 * inform upper layers of the transistion.
3064 */
3065 static void sky2_detach(struct net_device *dev)
3066 {
3067 if (netif_running(dev)) {
3068 netif_device_detach(dev); /* stop txq */
3069 sky2_down(dev);
3070 }
3071 }
3072
3073 /* Bring device back after doing sky2_detach */
3074 static int sky2_reattach(struct net_device *dev)
3075 {
3076 int err = 0;
3077
3078 if (netif_running(dev)) {
3079 err = sky2_up(dev);
3080 if (err) {
3081 printk(KERN_INFO PFX "%s: could not restart %d\n",
3082 dev->name, err);
3083 dev_close(dev);
3084 } else {
3085 netif_device_attach(dev);
3086 sky2_set_multicast(dev);
3087 }
3088 }
3089
3090 return err;
3091 }
3092
3093 static void sky2_restart(struct work_struct *work)
3094 {
3095 struct sky2_hw *hw = container_of(work, struct sky2_hw, restart_work);
3096 int i;
3097
3098 rtnl_lock();
3099 for (i = 0; i < hw->ports; i++)
3100 sky2_detach(hw->dev[i]);
3101
3102 napi_disable(&hw->napi);
3103 sky2_write32(hw, B0_IMSK, 0);
3104 sky2_reset(hw);
3105 sky2_write32(hw, B0_IMSK, Y2_IS_BASE);
3106 napi_enable(&hw->napi);
3107
3108 for (i = 0; i < hw->ports; i++)
3109 sky2_reattach(hw->dev[i]);
3110
3111 rtnl_unlock();
3112 }
3113
3114 static inline u8 sky2_wol_supported(const struct sky2_hw *hw)
3115 {
3116 return sky2_is_copper(hw) ? (WAKE_PHY | WAKE_MAGIC) : 0;
3117 }
3118
3119 static void sky2_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
3120 {
3121 const struct sky2_port *sky2 = netdev_priv(dev);
3122
3123 wol->supported = sky2_wol_supported(sky2->hw);
3124 wol->wolopts = sky2->wol;
3125 }
3126
3127 static int sky2_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
3128 {
3129 struct sky2_port *sky2 = netdev_priv(dev);
3130 struct sky2_hw *hw = sky2->hw;
3131
3132 if ((wol->wolopts & ~sky2_wol_supported(sky2->hw))
3133 || !device_can_wakeup(&hw->pdev->dev))
3134 return -EOPNOTSUPP;
3135
3136 sky2->wol = wol->wolopts;
3137
3138 if (hw->chip_id == CHIP_ID_YUKON_EC_U ||
3139 hw->chip_id == CHIP_ID_YUKON_EX ||
3140 hw->chip_id == CHIP_ID_YUKON_FE_P)
3141 sky2_write32(hw, B0_CTST, sky2->wol
3142 ? Y2_HW_WOL_ON : Y2_HW_WOL_OFF);
3143
3144 device_set_wakeup_enable(&hw->pdev->dev, sky2->wol);
3145
3146 if (!netif_running(dev))
3147 sky2_wol_init(sky2);
3148 return 0;
3149 }
3150
3151 static u32 sky2_supported_modes(const struct sky2_hw *hw)
3152 {
3153 if (sky2_is_copper(hw)) {
3154 u32 modes = SUPPORTED_10baseT_Half
3155 | SUPPORTED_10baseT_Full
3156 | SUPPORTED_100baseT_Half
3157 | SUPPORTED_100baseT_Full
3158 | SUPPORTED_Autoneg | SUPPORTED_TP;
3159
3160 if (hw->flags & SKY2_HW_GIGABIT)
3161 modes |= SUPPORTED_1000baseT_Half
3162 | SUPPORTED_1000baseT_Full;
3163 return modes;
3164 } else
3165 return SUPPORTED_1000baseT_Half
3166 | SUPPORTED_1000baseT_Full
3167 | SUPPORTED_Autoneg
3168 | SUPPORTED_FIBRE;
3169 }
3170
3171 static int sky2_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
3172 {
3173 struct sky2_port *sky2 = netdev_priv(dev);
3174 struct sky2_hw *hw = sky2->hw;
3175
3176 ecmd->transceiver = XCVR_INTERNAL;
3177 ecmd->supported = sky2_supported_modes(hw);
3178 ecmd->phy_address = PHY_ADDR_MARV;
3179 if (sky2_is_copper(hw)) {
3180 ecmd->port = PORT_TP;
3181 ecmd->speed = sky2->speed;
3182 } else {
3183 ecmd->speed = SPEED_1000;
3184 ecmd->port = PORT_FIBRE;
3185 }
3186
3187 ecmd->advertising = sky2->advertising;
3188 ecmd->autoneg = (sky2->flags & SKY2_FLAG_AUTO_SPEED)
3189 ? AUTONEG_ENABLE : AUTONEG_DISABLE;
3190 ecmd->duplex = sky2->duplex;
3191 return 0;
3192 }
3193
3194 static int sky2_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
3195 {
3196 struct sky2_port *sky2 = netdev_priv(dev);
3197 const struct sky2_hw *hw = sky2->hw;
3198 u32 supported = sky2_supported_modes(hw);
3199
3200 if (ecmd->autoneg == AUTONEG_ENABLE) {
3201 sky2->flags |= SKY2_FLAG_AUTO_SPEED;
3202 ecmd->advertising = supported;
3203 sky2->duplex = -1;
3204 sky2->speed = -1;
3205 } else {
3206 u32 setting;
3207
3208 switch (ecmd->speed) {
3209 case SPEED_1000:
3210 if (ecmd->duplex == DUPLEX_FULL)
3211 setting = SUPPORTED_1000baseT_Full;
3212 else if (ecmd->duplex == DUPLEX_HALF)
3213 setting = SUPPORTED_1000baseT_Half;
3214 else
3215 return -EINVAL;
3216 break;
3217 case SPEED_100:
3218 if (ecmd->duplex == DUPLEX_FULL)
3219 setting = SUPPORTED_100baseT_Full;
3220 else if (ecmd->duplex == DUPLEX_HALF)
3221 setting = SUPPORTED_100baseT_Half;
3222 else
3223 return -EINVAL;
3224 break;
3225
3226 case SPEED_10:
3227 if (ecmd->duplex == DUPLEX_FULL)
3228 setting = SUPPORTED_10baseT_Full;
3229 else if (ecmd->duplex == DUPLEX_HALF)
3230 setting = SUPPORTED_10baseT_Half;
3231 else
3232 return -EINVAL;
3233 break;
3234 default:
3235 return -EINVAL;
3236 }
3237
3238 if ((setting & supported) == 0)
3239 return -EINVAL;
3240
3241 sky2->speed = ecmd->speed;
3242 sky2->duplex = ecmd->duplex;
3243 sky2->flags &= ~SKY2_FLAG_AUTO_SPEED;
3244 }
3245
3246 sky2->advertising = ecmd->advertising;
3247
3248 if (netif_running(dev)) {
3249 sky2_phy_reinit(sky2);
3250 sky2_set_multicast(dev);
3251 }
3252
3253 return 0;
3254 }
3255
3256 static void sky2_get_drvinfo(struct net_device *dev,
3257 struct ethtool_drvinfo *info)
3258 {
3259 struct sky2_port *sky2 = netdev_priv(dev);
3260
3261 strcpy(info->driver, DRV_NAME);
3262 strcpy(info->version, DRV_VERSION);
3263 strcpy(info->fw_version, "N/A");
3264 strcpy(info->bus_info, pci_name(sky2->hw->pdev));
3265 }
3266
3267 static const struct sky2_stat {
3268 char name[ETH_GSTRING_LEN];
3269 u16 offset;
3270 } sky2_stats[] = {
3271 { "tx_bytes", GM_TXO_OK_HI },
3272 { "rx_bytes", GM_RXO_OK_HI },
3273 { "tx_broadcast", GM_TXF_BC_OK },
3274 { "rx_broadcast", GM_RXF_BC_OK },
3275 { "tx_multicast", GM_TXF_MC_OK },
3276 { "rx_multicast", GM_RXF_MC_OK },
3277 { "tx_unicast", GM_TXF_UC_OK },
3278 { "rx_unicast", GM_RXF_UC_OK },
3279 { "tx_mac_pause", GM_TXF_MPAUSE },
3280 { "rx_mac_pause", GM_RXF_MPAUSE },
3281 { "collisions", GM_TXF_COL },
3282 { "late_collision",GM_TXF_LAT_COL },
3283 { "aborted", GM_TXF_ABO_COL },
3284 { "single_collisions", GM_TXF_SNG_COL },
3285 { "multi_collisions", GM_TXF_MUL_COL },
3286
3287 { "rx_short", GM_RXF_SHT },
3288 { "rx_runt", GM_RXE_FRAG },
3289 { "rx_64_byte_packets", GM_RXF_64B },
3290 { "rx_65_to_127_byte_packets", GM_RXF_127B },
3291 { "rx_128_to_255_byte_packets", GM_RXF_255B },
3292 { "rx_256_to_511_byte_packets", GM_RXF_511B },
3293 { "rx_512_to_1023_byte_packets", GM_RXF_1023B },
3294 { "rx_1024_to_1518_byte_packets", GM_RXF_1518B },
3295 { "rx_1518_to_max_byte_packets", GM_RXF_MAX_SZ },
3296 { "rx_too_long", GM_RXF_LNG_ERR },
3297 { "rx_fifo_overflow", GM_RXE_FIFO_OV },
3298 { "rx_jabber", GM_RXF_JAB_PKT },
3299 { "rx_fcs_error", GM_RXF_FCS_ERR },
3300
3301 { "tx_64_byte_packets", GM_TXF_64B },
3302 { "tx_65_to_127_byte_packets", GM_TXF_127B },
3303 { "tx_128_to_255_byte_packets", GM_TXF_255B },
3304 { "tx_256_to_511_byte_packets", GM_TXF_511B },
3305 { "tx_512_to_1023_byte_packets", GM_TXF_1023B },
3306 { "tx_1024_to_1518_byte_packets", GM_TXF_1518B },
3307 { "tx_1519_to_max_byte_packets", GM_TXF_MAX_SZ },
3308 { "tx_fifo_underrun", GM_TXE_FIFO_UR },
3309 };
3310
3311 static u32 sky2_get_rx_csum(struct net_device *dev)
3312 {
3313 struct sky2_port *sky2 = netdev_priv(dev);
3314
3315 return !!(sky2->flags & SKY2_FLAG_RX_CHECKSUM);
3316 }
3317
3318 static int sky2_set_rx_csum(struct net_device *dev, u32 data)
3319 {
3320 struct sky2_port *sky2 = netdev_priv(dev);
3321
3322 if (data)
3323 sky2->flags |= SKY2_FLAG_RX_CHECKSUM;
3324 else
3325 sky2->flags &= ~SKY2_FLAG_RX_CHECKSUM;
3326
3327 sky2_write32(sky2->hw, Q_ADDR(rxqaddr[sky2->port], Q_CSR),
3328 data ? BMU_ENA_RX_CHKSUM : BMU_DIS_RX_CHKSUM);
3329
3330 return 0;
3331 }
3332
3333 static u32 sky2_get_msglevel(struct net_device *netdev)
3334 {
3335 struct sky2_port *sky2 = netdev_priv(netdev);
3336 return sky2->msg_enable;
3337 }
3338
3339 static int sky2_nway_reset(struct net_device *dev)
3340 {
3341 struct sky2_port *sky2 = netdev_priv(dev);
3342
3343 if (!netif_running(dev) || !(sky2->flags & SKY2_FLAG_AUTO_SPEED))
3344 return -EINVAL;
3345
3346 sky2_phy_reinit(sky2);
3347 sky2_set_multicast(dev);
3348
3349 return 0;
3350 }
3351
3352 static void sky2_phy_stats(struct sky2_port *sky2, u64 * data, unsigned count)
3353 {
3354 struct sky2_hw *hw = sky2->hw;
3355 unsigned port = sky2->port;
3356 int i;
3357
3358 data[0] = (u64) gma_read32(hw, port, GM_TXO_OK_HI) << 32
3359 | (u64) gma_read32(hw, port, GM_TXO_OK_LO);
3360 data[1] = (u64) gma_read32(hw, port, GM_RXO_OK_HI) << 32
3361 | (u64) gma_read32(hw, port, GM_RXO_OK_LO);
3362
3363 for (i = 2; i < count; i++)
3364 data[i] = (u64) gma_read32(hw, port, sky2_stats[i].offset);
3365 }
3366
3367 static void sky2_set_msglevel(struct net_device *netdev, u32 value)
3368 {
3369 struct sky2_port *sky2 = netdev_priv(netdev);
3370 sky2->msg_enable = value;
3371 }
3372
3373 static int sky2_get_sset_count(struct net_device *dev, int sset)
3374 {
3375 switch (sset) {
3376 case ETH_SS_STATS:
3377 return ARRAY_SIZE(sky2_stats);
3378 default:
3379 return -EOPNOTSUPP;
3380 }
3381 }
3382
3383 static void sky2_get_ethtool_stats(struct net_device *dev,
3384 struct ethtool_stats *stats, u64 * data)
3385 {
3386 struct sky2_port *sky2 = netdev_priv(dev);
3387
3388 sky2_phy_stats(sky2, data, ARRAY_SIZE(sky2_stats));
3389 }
3390
3391 static void sky2_get_strings(struct net_device *dev, u32 stringset, u8 * data)
3392 {
3393 int i;
3394
3395 switch (stringset) {
3396 case ETH_SS_STATS:
3397 for (i = 0; i < ARRAY_SIZE(sky2_stats); i++)
3398 memcpy(data + i * ETH_GSTRING_LEN,
3399 sky2_stats[i].name, ETH_GSTRING_LEN);
3400 break;
3401 }
3402 }
3403
3404 static int sky2_set_mac_address(struct net_device *dev, void *p)
3405 {
3406 struct sky2_port *sky2 = netdev_priv(dev);
3407 struct sky2_hw *hw = sky2->hw;
3408 unsigned port = sky2->port;
3409 const struct sockaddr *addr = p;
3410
3411 if (!is_valid_ether_addr(addr->sa_data))
3412 return -EADDRNOTAVAIL;
3413
3414 memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN);
3415 memcpy_toio(hw->regs + B2_MAC_1 + port * 8,
3416 dev->dev_addr, ETH_ALEN);
3417 memcpy_toio(hw->regs + B2_MAC_2 + port * 8,
3418 dev->dev_addr, ETH_ALEN);
3419
3420 /* virtual address for data */
3421 gma_set_addr(hw, port, GM_SRC_ADDR_2L, dev->dev_addr);
3422
3423 /* physical address: used for pause frames */
3424 gma_set_addr(hw, port, GM_SRC_ADDR_1L, dev->dev_addr);
3425
3426 return 0;
3427 }
3428
3429 static void inline sky2_add_filter(u8 filter[8], const u8 *addr)
3430 {
3431 u32 bit;
3432
3433 bit = ether_crc(ETH_ALEN, addr) & 63;
3434 filter[bit >> 3] |= 1 << (bit & 7);
3435 }
3436
3437 static void sky2_set_multicast(struct net_device *dev)
3438 {
3439 struct sky2_port *sky2 = netdev_priv(dev);
3440 struct sky2_hw *hw = sky2->hw;
3441 unsigned port = sky2->port;
3442 struct dev_mc_list *list = dev->mc_list;
3443 u16 reg;
3444 u8 filter[8];
3445 int rx_pause;
3446 static const u8 pause_mc_addr[ETH_ALEN] = { 0x1, 0x80, 0xc2, 0x0, 0x0, 0x1 };
3447
3448 rx_pause = (sky2->flow_status == FC_RX || sky2->flow_status == FC_BOTH);
3449 memset(filter, 0, sizeof(filter));
3450
3451 reg = gma_read16(hw, port, GM_RX_CTRL);
3452 reg |= GM_RXCR_UCF_ENA;
3453
3454 if (dev->flags & IFF_PROMISC) /* promiscuous */
3455 reg &= ~(GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA);
3456 else if (dev->flags & IFF_ALLMULTI)
3457 memset(filter, 0xff, sizeof(filter));
3458 else if (dev->mc_count == 0 && !rx_pause)
3459 reg &= ~GM_RXCR_MCF_ENA;
3460 else {
3461 int i;
3462 reg |= GM_RXCR_MCF_ENA;
3463
3464 if (rx_pause)
3465 sky2_add_filter(filter, pause_mc_addr);
3466
3467 for (i = 0; list && i < dev->mc_count; i++, list = list->next)
3468 sky2_add_filter(filter, list->dmi_addr);
3469 }
3470
3471 gma_write16(hw, port, GM_MC_ADDR_H1,
3472 (u16) filter[0] | ((u16) filter[1] << 8));
3473 gma_write16(hw, port, GM_MC_ADDR_H2,
3474 (u16) filter[2] | ((u16) filter[3] << 8));
3475 gma_write16(hw, port, GM_MC_ADDR_H3,
3476 (u16) filter[4] | ((u16) filter[5] << 8));
3477 gma_write16(hw, port, GM_MC_ADDR_H4,
3478 (u16) filter[6] | ((u16) filter[7] << 8));
3479
3480 gma_write16(hw, port, GM_RX_CTRL, reg);
3481 }
3482
3483 /* Can have one global because blinking is controlled by
3484 * ethtool and that is always under RTNL mutex
3485 */
3486 static void sky2_led(struct sky2_port *sky2, enum led_mode mode)
3487 {
3488 struct sky2_hw *hw = sky2->hw;
3489 unsigned port = sky2->port;
3490
3491 spin_lock_bh(&sky2->phy_lock);
3492 if (hw->chip_id == CHIP_ID_YUKON_EC_U ||
3493 hw->chip_id == CHIP_ID_YUKON_EX ||
3494 hw->chip_id == CHIP_ID_YUKON_SUPR) {
3495 u16 pg;
3496 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
3497 gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
3498
3499 switch (mode) {
3500 case MO_LED_OFF:
3501 gm_phy_write(hw, port, PHY_MARV_PHY_CTRL,
3502 PHY_M_LEDC_LOS_CTRL(8) |
3503 PHY_M_LEDC_INIT_CTRL(8) |
3504 PHY_M_LEDC_STA1_CTRL(8) |
3505 PHY_M_LEDC_STA0_CTRL(8));
3506 break;
3507 case MO_LED_ON:
3508 gm_phy_write(hw, port, PHY_MARV_PHY_CTRL,
3509 PHY_M_LEDC_LOS_CTRL(9) |
3510 PHY_M_LEDC_INIT_CTRL(9) |
3511 PHY_M_LEDC_STA1_CTRL(9) |
3512 PHY_M_LEDC_STA0_CTRL(9));
3513 break;
3514 case MO_LED_BLINK:
3515 gm_phy_write(hw, port, PHY_MARV_PHY_CTRL,
3516 PHY_M_LEDC_LOS_CTRL(0xa) |
3517 PHY_M_LEDC_INIT_CTRL(0xa) |
3518 PHY_M_LEDC_STA1_CTRL(0xa) |
3519 PHY_M_LEDC_STA0_CTRL(0xa));
3520 break;
3521 case MO_LED_NORM:
3522 gm_phy_write(hw, port, PHY_MARV_PHY_CTRL,
3523 PHY_M_LEDC_LOS_CTRL(1) |
3524 PHY_M_LEDC_INIT_CTRL(8) |
3525 PHY_M_LEDC_STA1_CTRL(7) |
3526 PHY_M_LEDC_STA0_CTRL(7));
3527 }
3528
3529 gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
3530 } else
3531 gm_phy_write(hw, port, PHY_MARV_LED_OVER,
3532 PHY_M_LED_MO_DUP(mode) |
3533 PHY_M_LED_MO_10(mode) |
3534 PHY_M_LED_MO_100(mode) |
3535 PHY_M_LED_MO_1000(mode) |
3536 PHY_M_LED_MO_RX(mode) |
3537 PHY_M_LED_MO_TX(mode));
3538
3539 spin_unlock_bh(&sky2->phy_lock);
3540 }
3541
3542 /* blink LED's for finding board */
3543 static int sky2_phys_id(struct net_device *dev, u32 data)
3544 {
3545 struct sky2_port *sky2 = netdev_priv(dev);
3546 unsigned int i;
3547
3548 if (data == 0)
3549 data = UINT_MAX;
3550
3551 for (i = 0; i < data; i++) {
3552 sky2_led(sky2, MO_LED_ON);
3553 if (msleep_interruptible(500))
3554 break;
3555 sky2_led(sky2, MO_LED_OFF);
3556 if (msleep_interruptible(500))
3557 break;
3558 }
3559 sky2_led(sky2, MO_LED_NORM);
3560
3561 return 0;
3562 }
3563
3564 static void sky2_get_pauseparam(struct net_device *dev,
3565 struct ethtool_pauseparam *ecmd)
3566 {
3567 struct sky2_port *sky2 = netdev_priv(dev);
3568
3569 switch (sky2->flow_mode) {
3570 case FC_NONE:
3571 ecmd->tx_pause = ecmd->rx_pause = 0;
3572 break;
3573 case FC_TX:
3574 ecmd->tx_pause = 1, ecmd->rx_pause = 0;
3575 break;
3576 case FC_RX:
3577 ecmd->tx_pause = 0, ecmd->rx_pause = 1;
3578 break;
3579 case FC_BOTH:
3580 ecmd->tx_pause = ecmd->rx_pause = 1;
3581 }
3582
3583 ecmd->autoneg = (sky2->flags & SKY2_FLAG_AUTO_PAUSE)
3584 ? AUTONEG_ENABLE : AUTONEG_DISABLE;
3585 }
3586
3587 static int sky2_set_pauseparam(struct net_device *dev,
3588 struct ethtool_pauseparam *ecmd)
3589 {
3590 struct sky2_port *sky2 = netdev_priv(dev);
3591
3592 if (ecmd->autoneg == AUTONEG_ENABLE)
3593 sky2->flags |= SKY2_FLAG_AUTO_PAUSE;
3594 else
3595 sky2->flags &= ~SKY2_FLAG_AUTO_PAUSE;
3596
3597 sky2->flow_mode = sky2_flow(ecmd->rx_pause, ecmd->tx_pause);
3598
3599 if (netif_running(dev))
3600 sky2_phy_reinit(sky2);
3601
3602 return 0;
3603 }
3604
3605 static int sky2_get_coalesce(struct net_device *dev,
3606 struct ethtool_coalesce *ecmd)
3607 {
3608 struct sky2_port *sky2 = netdev_priv(dev);
3609 struct sky2_hw *hw = sky2->hw;
3610
3611 if (sky2_read8(hw, STAT_TX_TIMER_CTRL) == TIM_STOP)
3612 ecmd->tx_coalesce_usecs = 0;
3613 else {
3614 u32 clks = sky2_read32(hw, STAT_TX_TIMER_INI);
3615 ecmd->tx_coalesce_usecs = sky2_clk2us(hw, clks);
3616 }
3617 ecmd->tx_max_coalesced_frames = sky2_read16(hw, STAT_TX_IDX_TH);
3618
3619 if (sky2_read8(hw, STAT_LEV_TIMER_CTRL) == TIM_STOP)
3620 ecmd->rx_coalesce_usecs = 0;
3621 else {
3622 u32 clks = sky2_read32(hw, STAT_LEV_TIMER_INI);
3623 ecmd->rx_coalesce_usecs = sky2_clk2us(hw, clks);
3624 }
3625 ecmd->rx_max_coalesced_frames = sky2_read8(hw, STAT_FIFO_WM);
3626
3627 if (sky2_read8(hw, STAT_ISR_TIMER_CTRL) == TIM_STOP)
3628 ecmd->rx_coalesce_usecs_irq = 0;
3629 else {
3630 u32 clks = sky2_read32(hw, STAT_ISR_TIMER_INI);
3631 ecmd->rx_coalesce_usecs_irq = sky2_clk2us(hw, clks);
3632 }
3633
3634 ecmd->rx_max_coalesced_frames_irq = sky2_read8(hw, STAT_FIFO_ISR_WM);
3635
3636 return 0;
3637 }
3638
3639 /* Note: this affect both ports */
3640 static int sky2_set_coalesce(struct net_device *dev,
3641 struct ethtool_coalesce *ecmd)
3642 {
3643 struct sky2_port *sky2 = netdev_priv(dev);
3644 struct sky2_hw *hw = sky2->hw;
3645 const u32 tmax = sky2_clk2us(hw, 0x0ffffff);
3646
3647 if (ecmd->tx_coalesce_usecs > tmax ||
3648 ecmd->rx_coalesce_usecs > tmax ||
3649 ecmd->rx_coalesce_usecs_irq > tmax)
3650 return -EINVAL;
3651
3652 if (ecmd->tx_max_coalesced_frames >= sky2->tx_ring_size-1)
3653 return -EINVAL;
3654 if (ecmd->rx_max_coalesced_frames > RX_MAX_PENDING)
3655 return -EINVAL;
3656 if (ecmd->rx_max_coalesced_frames_irq >RX_MAX_PENDING)
3657 return -EINVAL;
3658
3659 if (ecmd->tx_coalesce_usecs == 0)
3660 sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP);
3661 else {
3662 sky2_write32(hw, STAT_TX_TIMER_INI,
3663 sky2_us2clk(hw, ecmd->tx_coalesce_usecs));
3664 sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
3665 }
3666 sky2_write16(hw, STAT_TX_IDX_TH, ecmd->tx_max_coalesced_frames);
3667
3668 if (ecmd->rx_coalesce_usecs == 0)
3669 sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_STOP);
3670 else {
3671 sky2_write32(hw, STAT_LEV_TIMER_INI,
3672 sky2_us2clk(hw, ecmd->rx_coalesce_usecs));
3673 sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_START);
3674 }
3675 sky2_write8(hw, STAT_FIFO_WM, ecmd->rx_max_coalesced_frames);
3676
3677 if (ecmd->rx_coalesce_usecs_irq == 0)
3678 sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_STOP);
3679 else {
3680 sky2_write32(hw, STAT_ISR_TIMER_INI,
3681 sky2_us2clk(hw, ecmd->rx_coalesce_usecs_irq));
3682 sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START);
3683 }
3684 sky2_write8(hw, STAT_FIFO_ISR_WM, ecmd->rx_max_coalesced_frames_irq);
3685 return 0;
3686 }
3687
3688 static void sky2_get_ringparam(struct net_device *dev,
3689 struct ethtool_ringparam *ering)
3690 {
3691 struct sky2_port *sky2 = netdev_priv(dev);
3692
3693 ering->rx_max_pending = RX_MAX_PENDING;
3694 ering->rx_mini_max_pending = 0;
3695 ering->rx_jumbo_max_pending = 0;
3696 ering->tx_max_pending = TX_MAX_PENDING;
3697
3698 ering->rx_pending = sky2->rx_pending;
3699 ering->rx_mini_pending = 0;
3700 ering->rx_jumbo_pending = 0;
3701 ering->tx_pending = sky2->tx_pending;
3702 }
3703
3704 static int sky2_set_ringparam(struct net_device *dev,
3705 struct ethtool_ringparam *ering)
3706 {
3707 struct sky2_port *sky2 = netdev_priv(dev);
3708
3709 if (ering->rx_pending > RX_MAX_PENDING ||
3710 ering->rx_pending < 8 ||
3711 ering->tx_pending < TX_MIN_PENDING ||
3712 ering->tx_pending > TX_MAX_PENDING)
3713 return -EINVAL;
3714
3715 sky2_detach(dev);
3716
3717 sky2->rx_pending = ering->rx_pending;
3718 sky2->tx_pending = ering->tx_pending;
3719 sky2->tx_ring_size = roundup_pow_of_two(sky2->tx_pending+1);
3720
3721 return sky2_reattach(dev);
3722 }
3723
3724 static int sky2_get_regs_len(struct net_device *dev)
3725 {
3726 return 0x4000;
3727 }
3728
3729 /*
3730 * Returns copy of control register region
3731 * Note: ethtool_get_regs always provides full size (16k) buffer
3732 */
3733 static void sky2_get_regs(struct net_device *dev, struct ethtool_regs *regs,
3734 void *p)
3735 {
3736 const struct sky2_port *sky2 = netdev_priv(dev);
3737 const void __iomem *io = sky2->hw->regs;
3738 unsigned int b;
3739
3740 regs->version = 1;
3741
3742 for (b = 0; b < 128; b++) {
3743 /* This complicated switch statement is to make sure and
3744 * only access regions that are unreserved.
3745 * Some blocks are only valid on dual port cards.
3746 * and block 3 has some special diagnostic registers that
3747 * are poison.
3748 */
3749 switch (b) {
3750 case 3:
3751 /* skip diagnostic ram region */
3752 memcpy_fromio(p + 0x10, io + 0x10, 128 - 0x10);
3753 break;
3754
3755 /* dual port cards only */
3756 case 5: /* Tx Arbiter 2 */
3757 case 9: /* RX2 */
3758 case 14 ... 15: /* TX2 */
3759 case 17: case 19: /* Ram Buffer 2 */
3760 case 22 ... 23: /* Tx Ram Buffer 2 */
3761 case 25: /* Rx MAC Fifo 1 */
3762 case 27: /* Tx MAC Fifo 2 */
3763 case 31: /* GPHY 2 */
3764 case 40 ... 47: /* Pattern Ram 2 */
3765 case 52: case 54: /* TCP Segmentation 2 */
3766 case 112 ... 116: /* GMAC 2 */
3767 if (sky2->hw->ports == 1)
3768 goto reserved;
3769 /* fall through */
3770 case 0: /* Control */
3771 case 2: /* Mac address */
3772 case 4: /* Tx Arbiter 1 */
3773 case 7: /* PCI express reg */
3774 case 8: /* RX1 */
3775 case 12 ... 13: /* TX1 */
3776 case 16: case 18:/* Rx Ram Buffer 1 */
3777 case 20 ... 21: /* Tx Ram Buffer 1 */
3778 case 24: /* Rx MAC Fifo 1 */
3779 case 26: /* Tx MAC Fifo 1 */
3780 case 28 ... 29: /* Descriptor and status unit */
3781 case 30: /* GPHY 1*/
3782 case 32 ... 39: /* Pattern Ram 1 */
3783 case 48: case 50: /* TCP Segmentation 1 */
3784 case 56 ... 60: /* PCI space */
3785 case 80 ... 84: /* GMAC 1 */
3786 memcpy_fromio(p, io, 128);
3787 break;
3788 default:
3789 reserved:
3790 memset(p, 0, 128);
3791 }
3792
3793 p += 128;
3794 io += 128;
3795 }
3796 }
3797
3798 /* In order to do Jumbo packets on these chips, need to turn off the
3799 * transmit store/forward. Therefore checksum offload won't work.
3800 */
3801 static int no_tx_offload(struct net_device *dev)
3802 {
3803 const struct sky2_port *sky2 = netdev_priv(dev);
3804 const struct sky2_hw *hw = sky2->hw;
3805
3806 return dev->mtu > ETH_DATA_LEN && hw->chip_id == CHIP_ID_YUKON_EC_U;
3807 }
3808
3809 static int sky2_set_tx_csum(struct net_device *dev, u32 data)
3810 {
3811 if (data && no_tx_offload(dev))
3812 return -EINVAL;
3813
3814 return ethtool_op_set_tx_csum(dev, data);
3815 }
3816
3817
3818 static int sky2_set_tso(struct net_device *dev, u32 data)
3819 {
3820 if (data && no_tx_offload(dev))
3821 return -EINVAL;
3822
3823 return ethtool_op_set_tso(dev, data);
3824 }
3825
3826 static int sky2_get_eeprom_len(struct net_device *dev)
3827 {
3828 struct sky2_port *sky2 = netdev_priv(dev);
3829 struct sky2_hw *hw = sky2->hw;
3830 u16 reg2;
3831
3832 reg2 = sky2_pci_read16(hw, PCI_DEV_REG2);
3833 return 1 << ( ((reg2 & PCI_VPD_ROM_SZ) >> 14) + 8);
3834 }
3835
3836 static int sky2_vpd_wait(const struct sky2_hw *hw, int cap, u16 busy)
3837 {
3838 unsigned long start = jiffies;
3839
3840 while ( (sky2_pci_read16(hw, cap + PCI_VPD_ADDR) & PCI_VPD_ADDR_F) == busy) {
3841 /* Can take up to 10.6 ms for write */
3842 if (time_after(jiffies, start + HZ/4)) {
3843 dev_err(&hw->pdev->dev, PFX "VPD cycle timed out");
3844 return -ETIMEDOUT;
3845 }
3846 mdelay(1);
3847 }
3848
3849 return 0;
3850 }
3851
3852 static int sky2_vpd_read(struct sky2_hw *hw, int cap, void *data,
3853 u16 offset, size_t length)
3854 {
3855 int rc = 0;
3856
3857 while (length > 0) {
3858 u32 val;
3859
3860 sky2_pci_write16(hw, cap + PCI_VPD_ADDR, offset);
3861 rc = sky2_vpd_wait(hw, cap, 0);
3862 if (rc)
3863 break;
3864
3865 val = sky2_pci_read32(hw, cap + PCI_VPD_DATA);
3866
3867 memcpy(data, &val, min(sizeof(val), length));
3868 offset += sizeof(u32);
3869 data += sizeof(u32);
3870 length -= sizeof(u32);
3871 }
3872
3873 return rc;
3874 }
3875
3876 static int sky2_vpd_write(struct sky2_hw *hw, int cap, const void *data,
3877 u16 offset, unsigned int length)
3878 {
3879 unsigned int i;
3880 int rc = 0;
3881
3882 for (i = 0; i < length; i += sizeof(u32)) {
3883 u32 val = *(u32 *)(data + i);
3884
3885 sky2_pci_write32(hw, cap + PCI_VPD_DATA, val);
3886 sky2_pci_write32(hw, cap + PCI_VPD_ADDR, offset | PCI_VPD_ADDR_F);
3887
3888 rc = sky2_vpd_wait(hw, cap, PCI_VPD_ADDR_F);
3889 if (rc)
3890 break;
3891 }
3892 return rc;
3893 }
3894
3895 static int sky2_get_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom,
3896 u8 *data)
3897 {
3898 struct sky2_port *sky2 = netdev_priv(dev);
3899 int cap = pci_find_capability(sky2->hw->pdev, PCI_CAP_ID_VPD);
3900
3901 if (!cap)
3902 return -EINVAL;
3903
3904 eeprom->magic = SKY2_EEPROM_MAGIC;
3905
3906 return sky2_vpd_read(sky2->hw, cap, data, eeprom->offset, eeprom->len);
3907 }
3908
3909 static int sky2_set_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom,
3910 u8 *data)
3911 {
3912 struct sky2_port *sky2 = netdev_priv(dev);
3913 int cap = pci_find_capability(sky2->hw->pdev, PCI_CAP_ID_VPD);
3914
3915 if (!cap)
3916 return -EINVAL;
3917
3918 if (eeprom->magic != SKY2_EEPROM_MAGIC)
3919 return -EINVAL;
3920
3921 /* Partial writes not supported */
3922 if ((eeprom->offset & 3) || (eeprom->len & 3))
3923 return -EINVAL;
3924
3925 return sky2_vpd_write(sky2->hw, cap, data, eeprom->offset, eeprom->len);
3926 }
3927
3928
3929 static const struct ethtool_ops sky2_ethtool_ops = {
3930 .get_settings = sky2_get_settings,
3931 .set_settings = sky2_set_settings,
3932 .get_drvinfo = sky2_get_drvinfo,
3933 .get_wol = sky2_get_wol,
3934 .set_wol = sky2_set_wol,
3935 .get_msglevel = sky2_get_msglevel,
3936 .set_msglevel = sky2_set_msglevel,
3937 .nway_reset = sky2_nway_reset,
3938 .get_regs_len = sky2_get_regs_len,
3939 .get_regs = sky2_get_regs,
3940 .get_link = ethtool_op_get_link,
3941 .get_eeprom_len = sky2_get_eeprom_len,
3942 .get_eeprom = sky2_get_eeprom,
3943 .set_eeprom = sky2_set_eeprom,
3944 .set_sg = ethtool_op_set_sg,
3945 .set_tx_csum = sky2_set_tx_csum,
3946 .set_tso = sky2_set_tso,
3947 .get_rx_csum = sky2_get_rx_csum,
3948 .set_rx_csum = sky2_set_rx_csum,
3949 .get_strings = sky2_get_strings,
3950 .get_coalesce = sky2_get_coalesce,
3951 .set_coalesce = sky2_set_coalesce,
3952 .get_ringparam = sky2_get_ringparam,
3953 .set_ringparam = sky2_set_ringparam,
3954 .get_pauseparam = sky2_get_pauseparam,
3955 .set_pauseparam = sky2_set_pauseparam,
3956 .phys_id = sky2_phys_id,
3957 .get_sset_count = sky2_get_sset_count,
3958 .get_ethtool_stats = sky2_get_ethtool_stats,
3959 };
3960
3961 #ifdef CONFIG_SKY2_DEBUG
3962
3963 static struct dentry *sky2_debug;
3964
3965
3966 /*
3967 * Read and parse the first part of Vital Product Data
3968 */
3969 #define VPD_SIZE 128
3970 #define VPD_MAGIC 0x82
3971
3972 static const struct vpd_tag {
3973 char tag[2];
3974 char *label;
3975 } vpd_tags[] = {
3976 { "PN", "Part Number" },
3977 { "EC", "Engineering Level" },
3978 { "MN", "Manufacturer" },
3979 { "SN", "Serial Number" },
3980 { "YA", "Asset Tag" },
3981 { "VL", "First Error Log Message" },
3982 { "VF", "Second Error Log Message" },
3983 { "VB", "Boot Agent ROM Configuration" },
3984 { "VE", "EFI UNDI Configuration" },
3985 };
3986
3987 static void sky2_show_vpd(struct seq_file *seq, struct sky2_hw *hw)
3988 {
3989 size_t vpd_size;
3990 loff_t offs;
3991 u8 len;
3992 unsigned char *buf;
3993 u16 reg2;
3994
3995 reg2 = sky2_pci_read16(hw, PCI_DEV_REG2);
3996 vpd_size = 1 << ( ((reg2 & PCI_VPD_ROM_SZ) >> 14) + 8);
3997
3998 seq_printf(seq, "%s Product Data\n", pci_name(hw->pdev));
3999 buf = kmalloc(vpd_size, GFP_KERNEL);
4000 if (!buf) {
4001 seq_puts(seq, "no memory!\n");
4002 return;
4003 }
4004
4005 if (pci_read_vpd(hw->pdev, 0, vpd_size, buf) < 0) {
4006 seq_puts(seq, "VPD read failed\n");
4007 goto out;
4008 }
4009
4010 if (buf[0] != VPD_MAGIC) {
4011 seq_printf(seq, "VPD tag mismatch: %#x\n", buf[0]);
4012 goto out;
4013 }
4014 len = buf[1];
4015 if (len == 0 || len > vpd_size - 4) {
4016 seq_printf(seq, "Invalid id length: %d\n", len);
4017 goto out;
4018 }
4019
4020 seq_printf(seq, "%.*s\n", len, buf + 3);
4021 offs = len + 3;
4022
4023 while (offs < vpd_size - 4) {
4024 int i;
4025
4026 if (!memcmp("RW", buf + offs, 2)) /* end marker */
4027 break;
4028 len = buf[offs + 2];
4029 if (offs + len + 3 >= vpd_size)
4030 break;
4031
4032 for (i = 0; i < ARRAY_SIZE(vpd_tags); i++) {
4033 if (!memcmp(vpd_tags[i].tag, buf + offs, 2)) {
4034 seq_printf(seq, " %s: %.*s\n",
4035 vpd_tags[i].label, len, buf + offs + 3);
4036 break;
4037 }
4038 }
4039 offs += len + 3;
4040 }
4041 out:
4042 kfree(buf);
4043 }
4044
4045 static int sky2_debug_show(struct seq_file *seq, void *v)
4046 {
4047 struct net_device *dev = seq->private;
4048 const struct sky2_port *sky2 = netdev_priv(dev);
4049 struct sky2_hw *hw = sky2->hw;
4050 unsigned port = sky2->port;
4051 unsigned idx, last;
4052 int sop;
4053
4054 sky2_show_vpd(seq, hw);
4055
4056 seq_printf(seq, "\nIRQ src=%x mask=%x control=%x\n",
4057 sky2_read32(hw, B0_ISRC),
4058 sky2_read32(hw, B0_IMSK),
4059 sky2_read32(hw, B0_Y2_SP_ICR));
4060
4061 if (!netif_running(dev)) {
4062 seq_printf(seq, "network not running\n");
4063 return 0;
4064 }
4065
4066 napi_disable(&hw->napi);
4067 last = sky2_read16(hw, STAT_PUT_IDX);
4068
4069 if (hw->st_idx == last)
4070 seq_puts(seq, "Status ring (empty)\n");
4071 else {
4072 seq_puts(seq, "Status ring\n");
4073 for (idx = hw->st_idx; idx != last && idx < STATUS_RING_SIZE;
4074 idx = RING_NEXT(idx, STATUS_RING_SIZE)) {
4075 const struct sky2_status_le *le = hw->st_le + idx;
4076 seq_printf(seq, "[%d] %#x %d %#x\n",
4077 idx, le->opcode, le->length, le->status);
4078 }
4079 seq_puts(seq, "\n");
4080 }
4081
4082 seq_printf(seq, "Tx ring pending=%u...%u report=%d done=%d\n",
4083 sky2->tx_cons, sky2->tx_prod,
4084 sky2_read16(hw, port == 0 ? STAT_TXA1_RIDX : STAT_TXA2_RIDX),
4085 sky2_read16(hw, Q_ADDR(txqaddr[port], Q_DONE)));
4086
4087 /* Dump contents of tx ring */
4088 sop = 1;
4089 for (idx = sky2->tx_next; idx != sky2->tx_prod && idx < sky2->tx_ring_size;
4090 idx = RING_NEXT(idx, sky2->tx_ring_size)) {
4091 const struct sky2_tx_le *le = sky2->tx_le + idx;
4092 u32 a = le32_to_cpu(le->addr);
4093
4094 if (sop)
4095 seq_printf(seq, "%u:", idx);
4096 sop = 0;
4097
4098 switch(le->opcode & ~HW_OWNER) {
4099 case OP_ADDR64:
4100 seq_printf(seq, " %#x:", a);
4101 break;
4102 case OP_LRGLEN:
4103 seq_printf(seq, " mtu=%d", a);
4104 break;
4105 case OP_VLAN:
4106 seq_printf(seq, " vlan=%d", be16_to_cpu(le->length));
4107 break;
4108 case OP_TCPLISW:
4109 seq_printf(seq, " csum=%#x", a);
4110 break;
4111 case OP_LARGESEND:
4112 seq_printf(seq, " tso=%#x(%d)", a, le16_to_cpu(le->length));
4113 break;
4114 case OP_PACKET:
4115 seq_printf(seq, " %#x(%d)", a, le16_to_cpu(le->length));
4116 break;
4117 case OP_BUFFER:
4118 seq_printf(seq, " frag=%#x(%d)", a, le16_to_cpu(le->length));
4119 break;
4120 default:
4121 seq_printf(seq, " op=%#x,%#x(%d)", le->opcode,
4122 a, le16_to_cpu(le->length));
4123 }
4124
4125 if (le->ctrl & EOP) {
4126 seq_putc(seq, '\n');
4127 sop = 1;
4128 }
4129 }
4130
4131 seq_printf(seq, "\nRx ring hw get=%d put=%d last=%d\n",
4132 sky2_read16(hw, Y2_QADDR(rxqaddr[port], PREF_UNIT_GET_IDX)),
4133 sky2_read16(hw, Y2_QADDR(rxqaddr[port], PREF_UNIT_PUT_IDX)),
4134 sky2_read16(hw, Y2_QADDR(rxqaddr[port], PREF_UNIT_LAST_IDX)));
4135
4136 sky2_read32(hw, B0_Y2_SP_LISR);
4137 napi_enable(&hw->napi);
4138 return 0;
4139 }
4140
4141 static int sky2_debug_open(struct inode *inode, struct file *file)
4142 {
4143 return single_open(file, sky2_debug_show, inode->i_private);
4144 }
4145
4146 static const struct file_operations sky2_debug_fops = {
4147 .owner = THIS_MODULE,
4148 .open = sky2_debug_open,
4149 .read = seq_read,
4150 .llseek = seq_lseek,
4151 .release = single_release,
4152 };
4153
4154 /*
4155 * Use network device events to create/remove/rename
4156 * debugfs file entries
4157 */
4158 static int sky2_device_event(struct notifier_block *unused,
4159 unsigned long event, void *ptr)
4160 {
4161 struct net_device *dev = ptr;
4162 struct sky2_port *sky2 = netdev_priv(dev);
4163
4164 if (dev->netdev_ops->ndo_open != sky2_up || !sky2_debug)
4165 return NOTIFY_DONE;
4166
4167 switch(event) {
4168 case NETDEV_CHANGENAME:
4169 if (sky2->debugfs) {
4170 sky2->debugfs = debugfs_rename(sky2_debug, sky2->debugfs,
4171 sky2_debug, dev->name);
4172 }
4173 break;
4174
4175 case NETDEV_GOING_DOWN:
4176 if (sky2->debugfs) {
4177 printk(KERN_DEBUG PFX "%s: remove debugfs\n",
4178 dev->name);
4179 debugfs_remove(sky2->debugfs);
4180 sky2->debugfs = NULL;
4181 }
4182 break;
4183
4184 case NETDEV_UP:
4185 sky2->debugfs = debugfs_create_file(dev->name, S_IRUGO,
4186 sky2_debug, dev,
4187 &sky2_debug_fops);
4188 if (IS_ERR(sky2->debugfs))
4189 sky2->debugfs = NULL;
4190 }
4191
4192 return NOTIFY_DONE;
4193 }
4194
4195 static struct notifier_block sky2_notifier = {
4196 .notifier_call = sky2_device_event,
4197 };
4198
4199
4200 static __init void sky2_debug_init(void)
4201 {
4202 struct dentry *ent;
4203
4204 ent = debugfs_create_dir("sky2", NULL);
4205 if (!ent || IS_ERR(ent))
4206 return;
4207
4208 sky2_debug = ent;
4209 register_netdevice_notifier(&sky2_notifier);
4210 }
4211
4212 static __exit void sky2_debug_cleanup(void)
4213 {
4214 if (sky2_debug) {
4215 unregister_netdevice_notifier(&sky2_notifier);
4216 debugfs_remove(sky2_debug);
4217 sky2_debug = NULL;
4218 }
4219 }
4220
4221 #else
4222 #define sky2_debug_init()
4223 #define sky2_debug_cleanup()
4224 #endif
4225
4226 /* Two copies of network device operations to handle special case of
4227 not allowing netpoll on second port */
4228 static const struct net_device_ops sky2_netdev_ops[2] = {
4229 {
4230 .ndo_open = sky2_up,
4231 .ndo_stop = sky2_down,
4232 .ndo_start_xmit = sky2_xmit_frame,
4233 .ndo_do_ioctl = sky2_ioctl,
4234 .ndo_validate_addr = eth_validate_addr,
4235 .ndo_set_mac_address = sky2_set_mac_address,
4236 .ndo_set_multicast_list = sky2_set_multicast,
4237 .ndo_change_mtu = sky2_change_mtu,
4238 .ndo_tx_timeout = sky2_tx_timeout,
4239 #ifdef SKY2_VLAN_TAG_USED
4240 .ndo_vlan_rx_register = sky2_vlan_rx_register,
4241 #endif
4242 #ifdef CONFIG_NET_POLL_CONTROLLER
4243 .ndo_poll_controller = sky2_netpoll,
4244 #endif
4245 },
4246 {
4247 .ndo_open = sky2_up,
4248 .ndo_stop = sky2_down,
4249 .ndo_start_xmit = sky2_xmit_frame,
4250 .ndo_do_ioctl = sky2_ioctl,
4251 .ndo_validate_addr = eth_validate_addr,
4252 .ndo_set_mac_address = sky2_set_mac_address,
4253 .ndo_set_multicast_list = sky2_set_multicast,
4254 .ndo_change_mtu = sky2_change_mtu,
4255 .ndo_tx_timeout = sky2_tx_timeout,
4256 #ifdef SKY2_VLAN_TAG_USED
4257 .ndo_vlan_rx_register = sky2_vlan_rx_register,
4258 #endif
4259 },
4260 };
4261
4262 /* Initialize network device */
4263 static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw,
4264 unsigned port,
4265 int highmem, int wol)
4266 {
4267 struct sky2_port *sky2;
4268 struct net_device *dev = alloc_etherdev(sizeof(*sky2));
4269
4270 if (!dev) {
4271 dev_err(&hw->pdev->dev, "etherdev alloc failed\n");
4272 return NULL;
4273 }
4274
4275 SET_NETDEV_DEV(dev, &hw->pdev->dev);
4276 dev->irq = hw->pdev->irq;
4277 SET_ETHTOOL_OPS(dev, &sky2_ethtool_ops);
4278 dev->watchdog_timeo = TX_WATCHDOG;
4279 dev->netdev_ops = &sky2_netdev_ops[port];
4280
4281 sky2 = netdev_priv(dev);
4282 sky2->netdev = dev;
4283 sky2->hw = hw;
4284 sky2->msg_enable = netif_msg_init(debug, default_msg);
4285
4286 /* Auto speed and flow control */
4287 sky2->flags = SKY2_FLAG_AUTO_SPEED | SKY2_FLAG_AUTO_PAUSE;
4288 if (hw->chip_id != CHIP_ID_YUKON_XL)
4289 sky2->flags |= SKY2_FLAG_RX_CHECKSUM;
4290
4291 sky2->flow_mode = FC_BOTH;
4292
4293 sky2->duplex = -1;
4294 sky2->speed = -1;
4295 sky2->advertising = sky2_supported_modes(hw);
4296 sky2->wol = wol;
4297
4298 spin_lock_init(&sky2->phy_lock);
4299
4300 sky2->tx_pending = TX_DEF_PENDING;
4301 sky2->tx_ring_size = roundup_pow_of_two(TX_DEF_PENDING+1);
4302 sky2->rx_pending = RX_DEF_PENDING;
4303
4304 hw->dev[port] = dev;
4305
4306 sky2->port = port;
4307
4308 dev->features |= NETIF_F_TSO | NETIF_F_IP_CSUM | NETIF_F_SG;
4309 if (highmem)
4310 dev->features |= NETIF_F_HIGHDMA;
4311
4312 #ifdef SKY2_VLAN_TAG_USED
4313 /* The workaround for FE+ status conflicts with VLAN tag detection. */
4314 if (!(sky2->hw->chip_id == CHIP_ID_YUKON_FE_P &&
4315 sky2->hw->chip_rev == CHIP_REV_YU_FE2_A0)) {
4316 dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
4317 }
4318 #endif
4319
4320 /* read the mac address */
4321 memcpy_fromio(dev->dev_addr, hw->regs + B2_MAC_1 + port * 8, ETH_ALEN);
4322 memcpy(dev->perm_addr, dev->dev_addr, dev->addr_len);
4323
4324 return dev;
4325 }
4326
4327 static void __devinit sky2_show_addr(struct net_device *dev)
4328 {
4329 const struct sky2_port *sky2 = netdev_priv(dev);
4330
4331 if (netif_msg_probe(sky2))
4332 printk(KERN_INFO PFX "%s: addr %pM\n",
4333 dev->name, dev->dev_addr);
4334 }
4335
4336 /* Handle software interrupt used during MSI test */
4337 static irqreturn_t __devinit sky2_test_intr(int irq, void *dev_id)
4338 {
4339 struct sky2_hw *hw = dev_id;
4340 u32 status = sky2_read32(hw, B0_Y2_SP_ISRC2);
4341
4342 if (status == 0)
4343 return IRQ_NONE;
4344
4345 if (status & Y2_IS_IRQ_SW) {
4346 hw->flags |= SKY2_HW_USE_MSI;
4347 wake_up(&hw->msi_wait);
4348 sky2_write8(hw, B0_CTST, CS_CL_SW_IRQ);
4349 }
4350 sky2_write32(hw, B0_Y2_SP_ICR, 2);
4351
4352 return IRQ_HANDLED;
4353 }
4354
4355 /* Test interrupt path by forcing a a software IRQ */
4356 static int __devinit sky2_test_msi(struct sky2_hw *hw)
4357 {
4358 struct pci_dev *pdev = hw->pdev;
4359 int err;
4360
4361 init_waitqueue_head (&hw->msi_wait);
4362
4363 sky2_write32(hw, B0_IMSK, Y2_IS_IRQ_SW);
4364
4365 err = request_irq(pdev->irq, sky2_test_intr, 0, DRV_NAME, hw);
4366 if (err) {
4367 dev_err(&pdev->dev, "cannot assign irq %d\n", pdev->irq);
4368 return err;
4369 }
4370
4371 sky2_write8(hw, B0_CTST, CS_ST_SW_IRQ);
4372 sky2_read8(hw, B0_CTST);
4373
4374 wait_event_timeout(hw->msi_wait, (hw->flags & SKY2_HW_USE_MSI), HZ/10);
4375
4376 if (!(hw->flags & SKY2_HW_USE_MSI)) {
4377 /* MSI test failed, go back to INTx mode */
4378 dev_info(&pdev->dev, "No interrupt generated using MSI, "
4379 "switching to INTx mode.\n");
4380
4381 err = -EOPNOTSUPP;
4382 sky2_write8(hw, B0_CTST, CS_CL_SW_IRQ);
4383 }
4384
4385 sky2_write32(hw, B0_IMSK, 0);
4386 sky2_read32(hw, B0_IMSK);
4387
4388 free_irq(pdev->irq, hw);
4389
4390 return err;
4391 }
4392
4393 /* This driver supports yukon2 chipset only */
4394 static const char *sky2_name(u8 chipid, char *buf, int sz)
4395 {
4396 const char *name[] = {
4397 "XL", /* 0xb3 */
4398 "EC Ultra", /* 0xb4 */
4399 "Extreme", /* 0xb5 */
4400 "EC", /* 0xb6 */
4401 "FE", /* 0xb7 */
4402 "FE+", /* 0xb8 */
4403 "Supreme", /* 0xb9 */
4404 "UL 2", /* 0xba */
4405 };
4406
4407 if (chipid >= CHIP_ID_YUKON_XL && chipid < CHIP_ID_YUKON_UL_2)
4408 strncpy(buf, name[chipid - CHIP_ID_YUKON_XL], sz);
4409 else
4410 snprintf(buf, sz, "(chip %#x)", chipid);
4411 return buf;
4412 }
4413
4414 static int __devinit sky2_probe(struct pci_dev *pdev,
4415 const struct pci_device_id *ent)
4416 {
4417 struct net_device *dev;
4418 struct sky2_hw *hw;
4419 int err, using_dac = 0, wol_default;
4420 u32 reg;
4421 char buf1[16];
4422
4423 err = pci_enable_device(pdev);
4424 if (err) {
4425 dev_err(&pdev->dev, "cannot enable PCI device\n");
4426 goto err_out;
4427 }
4428
4429 /* Get configuration information
4430 * Note: only regular PCI config access once to test for HW issues
4431 * other PCI access through shared memory for speed and to
4432 * avoid MMCONFIG problems.
4433 */
4434 err = pci_read_config_dword(pdev, PCI_DEV_REG2, &reg);
4435 if (err) {
4436 dev_err(&pdev->dev, "PCI read config failed\n");
4437 goto err_out;
4438 }
4439
4440 if (~reg == 0) {
4441 dev_err(&pdev->dev, "PCI configuration read error\n");
4442 goto err_out;
4443 }
4444
4445 err = pci_request_regions(pdev, DRV_NAME);
4446 if (err) {
4447 dev_err(&pdev->dev, "cannot obtain PCI resources\n");
4448 goto err_out_disable;
4449 }
4450
4451 pci_set_master(pdev);
4452
4453 if (sizeof(dma_addr_t) > sizeof(u32) &&
4454 !(err = pci_set_dma_mask(pdev, DMA_BIT_MASK(64)))) {
4455 using_dac = 1;
4456 err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
4457 if (err < 0) {
4458 dev_err(&pdev->dev, "unable to obtain 64 bit DMA "
4459 "for consistent allocations\n");
4460 goto err_out_free_regions;
4461 }
4462 } else {
4463 err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
4464 if (err) {
4465 dev_err(&pdev->dev, "no usable DMA configuration\n");
4466 goto err_out_free_regions;
4467 }
4468 }
4469
4470
4471 #ifdef __BIG_ENDIAN
4472 /* The sk98lin vendor driver uses hardware byte swapping but
4473 * this driver uses software swapping.
4474 */
4475 reg &= ~PCI_REV_DESC;
4476 err = pci_write_config_dword(pdev,PCI_DEV_REG2, reg);
4477 if (err) {
4478 dev_err(&pdev->dev, "PCI write config failed\n");
4479 goto err_out_free_regions;
4480 }
4481 #endif
4482
4483 wol_default = device_may_wakeup(&pdev->dev) ? WAKE_MAGIC : 0;
4484
4485 err = -ENOMEM;
4486 hw = kzalloc(sizeof(*hw), GFP_KERNEL);
4487 if (!hw) {
4488 dev_err(&pdev->dev, "cannot allocate hardware struct\n");
4489 goto err_out_free_regions;
4490 }
4491
4492 hw->pdev = pdev;
4493
4494 hw->regs = ioremap_nocache(pci_resource_start(pdev, 0), 0x4000);
4495 if (!hw->regs) {
4496 dev_err(&pdev->dev, "cannot map device registers\n");
4497 goto err_out_free_hw;
4498 }
4499
4500 /* ring for status responses */
4501 hw->st_le = pci_alloc_consistent(pdev, STATUS_LE_BYTES, &hw->st_dma);
4502 if (!hw->st_le)
4503 goto err_out_iounmap;
4504
4505 err = sky2_init(hw);
4506 if (err)
4507 goto err_out_iounmap;
4508
4509 dev_info(&pdev->dev, "Yukon-2 %s chip revision %d\n",
4510 sky2_name(hw->chip_id, buf1, sizeof(buf1)), hw->chip_rev);
4511
4512 sky2_reset(hw);
4513
4514 dev = sky2_init_netdev(hw, 0, using_dac, wol_default);
4515 if (!dev) {
4516 err = -ENOMEM;
4517 goto err_out_free_pci;
4518 }
4519
4520 if (!disable_msi && pci_enable_msi(pdev) == 0) {
4521 err = sky2_test_msi(hw);
4522 if (err == -EOPNOTSUPP)
4523 pci_disable_msi(pdev);
4524 else if (err)
4525 goto err_out_free_netdev;
4526 }
4527
4528 err = register_netdev(dev);
4529 if (err) {
4530 dev_err(&pdev->dev, "cannot register net device\n");
4531 goto err_out_free_netdev;
4532 }
4533
4534 netif_napi_add(dev, &hw->napi, sky2_poll, NAPI_WEIGHT);
4535
4536 err = request_irq(pdev->irq, sky2_intr,
4537 (hw->flags & SKY2_HW_USE_MSI) ? 0 : IRQF_SHARED,
4538 dev->name, hw);
4539 if (err) {
4540 dev_err(&pdev->dev, "cannot assign irq %d\n", pdev->irq);
4541 goto err_out_unregister;
4542 }
4543 sky2_write32(hw, B0_IMSK, Y2_IS_BASE);
4544 napi_enable(&hw->napi);
4545
4546 sky2_show_addr(dev);
4547
4548 if (hw->ports > 1) {
4549 struct net_device *dev1;
4550
4551 dev1 = sky2_init_netdev(hw, 1, using_dac, wol_default);
4552 if (!dev1)
4553 dev_warn(&pdev->dev, "allocation for second device failed\n");
4554 else if ((err = register_netdev(dev1))) {
4555 dev_warn(&pdev->dev,
4556 "register of second port failed (%d)\n", err);
4557 hw->dev[1] = NULL;
4558 free_netdev(dev1);
4559 } else
4560 sky2_show_addr(dev1);
4561 }
4562
4563 setup_timer(&hw->watchdog_timer, sky2_watchdog, (unsigned long) hw);
4564 INIT_WORK(&hw->restart_work, sky2_restart);
4565
4566 pci_set_drvdata(pdev, hw);
4567
4568 return 0;
4569
4570 err_out_unregister:
4571 if (hw->flags & SKY2_HW_USE_MSI)
4572 pci_disable_msi(pdev);
4573 unregister_netdev(dev);
4574 err_out_free_netdev:
4575 free_netdev(dev);
4576 err_out_free_pci:
4577 sky2_write8(hw, B0_CTST, CS_RST_SET);
4578 pci_free_consistent(pdev, STATUS_LE_BYTES, hw->st_le, hw->st_dma);
4579 err_out_iounmap:
4580 iounmap(hw->regs);
4581 err_out_free_hw:
4582 kfree(hw);
4583 err_out_free_regions:
4584 pci_release_regions(pdev);
4585 err_out_disable:
4586 pci_disable_device(pdev);
4587 err_out:
4588 pci_set_drvdata(pdev, NULL);
4589 return err;
4590 }
4591
4592 static void __devexit sky2_remove(struct pci_dev *pdev)
4593 {
4594 struct sky2_hw *hw = pci_get_drvdata(pdev);
4595 int i;
4596
4597 if (!hw)
4598 return;
4599
4600 del_timer_sync(&hw->watchdog_timer);
4601 cancel_work_sync(&hw->restart_work);
4602
4603 for (i = hw->ports-1; i >= 0; --i)
4604 unregister_netdev(hw->dev[i]);
4605
4606 sky2_write32(hw, B0_IMSK, 0);
4607
4608 sky2_power_aux(hw);
4609
4610 sky2_write8(hw, B0_CTST, CS_RST_SET);
4611 sky2_read8(hw, B0_CTST);
4612
4613 free_irq(pdev->irq, hw);
4614 if (hw->flags & SKY2_HW_USE_MSI)
4615 pci_disable_msi(pdev);
4616 pci_free_consistent(pdev, STATUS_LE_BYTES, hw->st_le, hw->st_dma);
4617 pci_release_regions(pdev);
4618 pci_disable_device(pdev);
4619
4620 for (i = hw->ports-1; i >= 0; --i)
4621 free_netdev(hw->dev[i]);
4622
4623 iounmap(hw->regs);
4624 kfree(hw);
4625
4626 pci_set_drvdata(pdev, NULL);
4627 }
4628
4629 #ifdef CONFIG_PM
4630 static int sky2_suspend(struct pci_dev *pdev, pm_message_t state)
4631 {
4632 struct sky2_hw *hw = pci_get_drvdata(pdev);
4633 int i, wol = 0;
4634
4635 if (!hw)
4636 return 0;
4637
4638 del_timer_sync(&hw->watchdog_timer);
4639 cancel_work_sync(&hw->restart_work);
4640
4641 rtnl_lock();
4642 for (i = 0; i < hw->ports; i++) {
4643 struct net_device *dev = hw->dev[i];
4644 struct sky2_port *sky2 = netdev_priv(dev);
4645
4646 sky2_detach(dev);
4647
4648 if (sky2->wol)
4649 sky2_wol_init(sky2);
4650
4651 wol |= sky2->wol;
4652 }
4653
4654 sky2_write32(hw, B0_IMSK, 0);
4655 napi_disable(&hw->napi);
4656 sky2_power_aux(hw);
4657 rtnl_unlock();
4658
4659 pci_save_state(pdev);
4660 pci_enable_wake(pdev, pci_choose_state(pdev, state), wol);
4661 pci_set_power_state(pdev, pci_choose_state(pdev, state));
4662
4663 return 0;
4664 }
4665
4666 static int sky2_resume(struct pci_dev *pdev)
4667 {
4668 struct sky2_hw *hw = pci_get_drvdata(pdev);
4669 int i, err;
4670
4671 if (!hw)
4672 return 0;
4673
4674 err = pci_set_power_state(pdev, PCI_D0);
4675 if (err)
4676 goto out;
4677
4678 err = pci_restore_state(pdev);
4679 if (err)
4680 goto out;
4681
4682 pci_enable_wake(pdev, PCI_D0, 0);
4683
4684 /* Re-enable all clocks */
4685 if (hw->chip_id == CHIP_ID_YUKON_EX ||
4686 hw->chip_id == CHIP_ID_YUKON_EC_U ||
4687 hw->chip_id == CHIP_ID_YUKON_FE_P)
4688 sky2_pci_write32(hw, PCI_DEV_REG3, 0);
4689
4690 sky2_reset(hw);
4691 sky2_write32(hw, B0_IMSK, Y2_IS_BASE);
4692 napi_enable(&hw->napi);
4693
4694 rtnl_lock();
4695 for (i = 0; i < hw->ports; i++) {
4696 err = sky2_reattach(hw->dev[i]);
4697 if (err)
4698 goto out;
4699 }
4700 rtnl_unlock();
4701
4702 return 0;
4703 out:
4704 rtnl_unlock();
4705
4706 dev_err(&pdev->dev, "resume failed (%d)\n", err);
4707 pci_disable_device(pdev);
4708 return err;
4709 }
4710 #endif
4711
4712 static void sky2_shutdown(struct pci_dev *pdev)
4713 {
4714 struct sky2_hw *hw = pci_get_drvdata(pdev);
4715 int i, wol = 0;
4716
4717 if (!hw)
4718 return;
4719
4720 rtnl_lock();
4721 del_timer_sync(&hw->watchdog_timer);
4722
4723 for (i = 0; i < hw->ports; i++) {
4724 struct net_device *dev = hw->dev[i];
4725 struct sky2_port *sky2 = netdev_priv(dev);
4726
4727 if (sky2->wol) {
4728 wol = 1;
4729 sky2_wol_init(sky2);
4730 }
4731 }
4732
4733 if (wol)
4734 sky2_power_aux(hw);
4735 rtnl_unlock();
4736
4737 pci_enable_wake(pdev, PCI_D3hot, wol);
4738 pci_enable_wake(pdev, PCI_D3cold, wol);
4739
4740 pci_disable_device(pdev);
4741 pci_set_power_state(pdev, PCI_D3hot);
4742 }
4743
4744 static struct pci_driver sky2_driver = {
4745 .name = DRV_NAME,
4746 .id_table = sky2_id_table,
4747 .probe = sky2_probe,
4748 .remove = __devexit_p(sky2_remove),
4749 #ifdef CONFIG_PM
4750 .suspend = sky2_suspend,
4751 .resume = sky2_resume,
4752 #endif
4753 .shutdown = sky2_shutdown,
4754 };
4755
4756 static int __init sky2_init_module(void)
4757 {
4758 pr_info(PFX "driver version " DRV_VERSION "\n");
4759
4760 sky2_debug_init();
4761 return pci_register_driver(&sky2_driver);
4762 }
4763
4764 static void __exit sky2_cleanup_module(void)
4765 {
4766 pci_unregister_driver(&sky2_driver);
4767 sky2_debug_cleanup();
4768 }
4769
4770 module_init(sky2_init_module);
4771 module_exit(sky2_cleanup_module);
4772
4773 MODULE_DESCRIPTION("Marvell Yukon 2 Gigabit Ethernet driver");
4774 MODULE_AUTHOR("Stephen Hemminger <shemminger@linux-foundation.org>");
4775 MODULE_LICENSE("GPL");
4776 MODULE_VERSION(DRV_VERSION);
Linux kernel - Deliverables
This page took 0.17842 seconds and 5 git commands to generate.