drivers/net/wireless/Kconfig

   1 #
   2 # Wireless LAN device configuration
   3 #
   4
   5 menu "Wireless LAN"
   6         depends on !S390
   7
   8 config WLAN_PRE80211
   9         bool "Wireless LAN (pre-802.11)"
  10         depends on NETDEVICES
  11         ---help---
  12           Say Y if you have any pre-802.11 wireless LAN hardware.
  13
  14           This option does not affect the kernel build, it only
  15           lets you choose drivers.
  16
  17 config STRIP
  18         tristate "STRIP (Metricom starmode radio IP)"
  19         depends on INET && WLAN_PRE80211
  20         select WIRELESS_EXT
  21         ---help---
  22           Say Y if you have a Metricom radio and intend to use Starmode Radio
  23           IP. STRIP is a radio protocol developed for the MosquitoNet project
  24           (on the WWW at <http://mosquitonet.stanford.edu/>) to send Internet
  25           traffic using Metricom radios.  Metricom radios are small, battery
  26           powered, 100kbit/sec packet radio transceivers, about the size and
  27           weight of a cellular telephone. (You may also have heard them called
  28           "Metricom modems" but we avoid the term "modem" because it misleads
  29           many people into thinking that you can plug a Metricom modem into a
  30           phone line and use it as a modem.)
  31
  32           You can use STRIP on any Linux machine with a serial port, although
  33           it is obviously most useful for people with laptop computers. If you
  34           think you might get a Metricom radio in the future, there is no harm
  35           in saying Y to STRIP now, except that it makes the kernel a bit
  36           bigger.
  37
  38           To compile this as a module, choose M here: the module will be
  39           called strip.
  40
  41 config ARLAN
  42         tristate "Aironet Arlan 655 & IC2200 DS support"
  43         depends on ISA && !64BIT && WLAN_PRE80211
  44         select WIRELESS_EXT
  45         ---help---
  46           Aironet makes Arlan, a class of wireless LAN adapters. These use the
  47           www.Telxon.com chip, which is also used on several similar cards.
  48           This driver is tested on the 655 and IC2200 series cards. Look at
  49           <http://www.ylenurme.ee/~elmer/655/> for the latest information.
  50
  51           The driver is built as two modules, arlan and arlan-proc. The latter
  52           is the /proc interface and is not needed most of time.
  53
  54           On some computers the card ends up in non-valid state after some
  55           time. Use a ping-reset script to clear it.
  56
  57 config WAVELAN
  58         tristate "AT&T/Lucent old WaveLAN & DEC RoamAbout DS ISA support"
  59         depends on ISA && WLAN_PRE80211
  60         select WIRELESS_EXT
  61         ---help---
  62           The Lucent WaveLAN (formerly NCR and AT&T; or DEC RoamAbout DS) is
  63           a Radio LAN (wireless Ethernet-like Local Area Network) using the
  64           radio frequencies 900 MHz and 2.4 GHz.
  65
  66           If you want to use an ISA WaveLAN card under Linux, say Y and read
  67           the Ethernet-HOWTO, available from
  68           <http://www.tldp.org/docs.html#howto>. Some more specific
  69           information is contained in
  70           <file:Documentation/networking/wavelan.txt> and in the source code
  71           <file:drivers/net/wireless/wavelan.p.h>.
  72
  73           You will also need the wireless tools package available from
  74           <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
  75           Please read the man pages contained therein.
  76
  77           To compile this driver as a module, choose M here: the module will be
  78           called wavelan.
  79
  80 config PCMCIA_WAVELAN
  81         tristate "AT&T/Lucent old WaveLAN Pcmcia wireless support"
  82         depends on PCMCIA && WLAN_PRE80211
  83         select WIRELESS_EXT
  84         help
  85           Say Y here if you intend to attach an AT&T/Lucent Wavelan PCMCIA
  86           (PC-card) wireless Ethernet networking card to your computer.  This
  87           driver is for the non-IEEE-802.11 Wavelan cards.
  88
  89           To compile this driver as a module, choose M here: the module will be
  90           called wavelan_cs.  If unsure, say N.
  91
  92 config PCMCIA_NETWAVE
  93         tristate "Xircom Netwave AirSurfer Pcmcia wireless support"
  94         depends on PCMCIA && WLAN_PRE80211
  95         select WIRELESS_EXT
  96         help
  97           Say Y here if you intend to attach this type of PCMCIA (PC-card)
  98           wireless Ethernet networking card to your computer.
  99
 100           To compile this driver as a module, choose M here: the module will be
 101           called netwave_cs.  If unsure, say N.
 102
 103
 104 config WLAN_80211
 105         bool "Wireless LAN (IEEE 802.11)"
 106         depends on NETDEVICES
 107         ---help---
 108           Say Y if you have any 802.11 wireless LAN hardware.
 109
 110           This option does not affect the kernel build, it only
 111           lets you choose drivers.
 112
 113 config PCMCIA_RAYCS
 114         tristate "Aviator/Raytheon 2.4MHz wireless support"
 115         depends on PCMCIA && WLAN_80211
 116         select WIRELESS_EXT
 117         ---help---
 118           Say Y here if you intend to attach an Aviator/Raytheon PCMCIA
 119           (PC-card) wireless Ethernet networking card to your computer.
 120           Please read the file <file:Documentation/networking/ray_cs.txt> for
 121           details.
 122
 123           To compile this driver as a module, choose M here: the module will be
 124           called ray_cs.  If unsure, say N.
 125
 126 config IPW2100
 127         tristate "Intel PRO/Wireless 2100 Network Connection"
 128         depends on PCI && WLAN_80211
 129         select WIRELESS_EXT
 130         select FW_LOADER
 131         select IEEE80211
 132         ---help---
 133           A driver for the Intel PRO/Wireless 2100 Network
 134           Connection 802.11b wireless network adapter.
 135
 136           See <file:Documentation/networking/README.ipw2100> for information on
 137           the capabilities currently enabled in this driver and for tips
 138           for debugging issues and problems.
 139
 140           In order to use this driver, you will need a firmware image for it.
 141           You can obtain the firmware from
 142           <http://ipw2100.sf.net/>.  Once you have the firmware image, you
 143           will need to place it in /lib/firmware.
 144
 145           You will also very likely need the Wireless Tools in order to
 146           configure your card:
 147
 148           <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
 149
 150           If you want to compile the driver as a module ( = code which can be
 151           inserted in and removed from the running kernel whenever you want),
 152           say M here and read <file:Documentation/kbuild/modules.txt>.
 153           The module will be called ipw2100.ko.
 154
 155 config IPW2100_MONITOR
 156         bool "Enable promiscuous mode"
 157         depends on IPW2100
 158         ---help---
 159           Enables promiscuous/monitor mode support for the ipw2100 driver.
 160           With this feature compiled into the driver, you can switch to
 161           promiscuous mode via the Wireless Tool's Monitor mode.  While in this
 162           mode, no packets can be sent.
 163
 164 config IPW2100_DEBUG
 165         bool "Enable full debugging output in IPW2100 module."
 166         depends on IPW2100
 167         ---help---
 168           This option will enable debug tracing output for the IPW2100.
 169
 170           This will result in the kernel module being ~60k larger.  You can
 171           control which debug output is sent to the kernel log by setting the
 172           value in
 173
 174           /sys/bus/pci/drivers/ipw2100/debug_level
 175
 176           This entry will only exist if this option is enabled.
 177
 178           If you are not trying to debug or develop the IPW2100 driver, you
 179           most likely want to say N here.
 180
 181 config IPW2200
 182         tristate "Intel PRO/Wireless 2200BG and 2915ABG Network Connection"
 183         depends on PCI && WLAN_80211
 184         select WIRELESS_EXT
 185         select FW_LOADER
 186         select IEEE80211
 187         ---help---
 188           A driver for the Intel PRO/Wireless 2200BG and 2915ABG Network
 189           Connection adapters.
 190
 191           See <file:Documentation/networking/README.ipw2200> for
 192           information on the capabilities currently enabled in this
 193           driver and for tips for debugging issues and problems.
 194
 195           In order to use this driver, you will need a firmware image for it.
 196           You can obtain the firmware from
 197           <http://ipw2200.sf.net/>.  See the above referenced README.ipw2200
 198           for information on where to install the firmware images.
 199
 200           You will also very likely need the Wireless Tools in order to
 201           configure your card:
 202
 203           <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
 204
 205           If you want to compile the driver as a module ( = code which can be
 206           inserted in and removed from the running kernel whenever you want),
 207           say M here and read <file:Documentation/kbuild/modules.txt>.
 208           The module will be called ipw2200.ko.
 209
 210 config IPW2200_MONITOR
 211         bool "Enable promiscuous mode"
 212         depends on IPW2200
 213         ---help---
 214           Enables promiscuous/monitor mode support for the ipw2200 driver.
 215           With this feature compiled into the driver, you can switch to
 216           promiscuous mode via the Wireless Tool's Monitor mode.  While in this
 217           mode, no packets can be sent.
 218
 219 config IPW2200_RADIOTAP
 220         bool "Enable radiotap format 802.11 raw packet support"
 221         depends on IPW2200_MONITOR
 222
 223 config IPW2200_PROMISCUOUS
 224         bool "Enable creation of a RF radiotap promiscuous interface"
 225         depends on IPW2200_MONITOR
 226         select IPW2200_RADIOTAP
 227         ---help---
 228           Enables the creation of a second interface prefixed 'rtap'.
 229           This second interface will provide every received in radiotap
 230           format.
 231
 232           This is useful for performing wireless network analysis while
 233           maintaining an active association.
 234
 235           Example usage:
 236
 237             % modprobe ipw2200 rtap_iface=1
 238             % ifconfig rtap0 up
 239             % tethereal -i rtap0
 240
 241           If you do not specify 'rtap_iface=1' as a module parameter then
 242           the rtap interface will not be created and you will need to turn
 243           it on via sysfs:
 244
 245             % echo 1 > /sys/bus/pci/drivers/ipw2200/*/rtap_iface
 246
 247 config IPW2200_QOS
 248         bool "Enable QoS support"
 249         depends on IPW2200 && EXPERIMENTAL
 250
 251 config IPW2200_DEBUG
 252         bool "Enable full debugging output in IPW2200 module."
 253         depends on IPW2200
 254         ---help---
 255           This option will enable low level debug tracing output for IPW2200.
 256
 257           Note, normal debug code is already compiled in. This low level
 258           debug option enables debug on hot paths (e.g Tx, Rx, ISR) and
 259           will result in the kernel module being ~70 larger.  Most users
 260           will typically not need this high verbosity debug information.
 261
 262           If you are not sure, say N here.
 263
 264 config LIBERTAS
 265         tristate "Marvell 8xxx Libertas WLAN driver support"
 266         depends on WLAN_80211
 267         select WIRELESS_EXT
 268         select IEEE80211
 269         select FW_LOADER
 270         ---help---
 271           A library for Marvell Libertas 8xxx devices.
 272
 273 config LIBERTAS_USB
 274         tristate "Marvell Libertas 8388 USB 802.11b/g cards"
 275         depends on LIBERTAS && USB
 276         ---help---
 277           A driver for Marvell Libertas 8388 USB devices.
 278
 279 config LIBERTAS_CS
 280         tristate "Marvell Libertas 8385 CompactFlash 802.11b/g cards"
 281         depends on LIBERTAS && PCMCIA && EXPERIMENTAL
 282         select FW_LOADER
 283         ---help---
 284           A driver for Marvell Libertas 8385 CompactFlash devices.
 285
 286 config LIBERTAS_SDIO
 287         tristate "Marvell Libertas 8385 and 8686 SDIO 802.11b/g cards"
 288         depends on LIBERTAS && MMC
 289         ---help---
 290           A driver for Marvell Libertas 8385 and 8686 SDIO devices.
 291
 292 config LIBERTAS_DEBUG
 293         bool "Enable full debugging output in the Libertas module."
 294         depends on LIBERTAS
 295         ---help---
 296           Debugging support.
 297
 298 config AIRO
 299         tristate "Cisco/Aironet 34X/35X/4500/4800 ISA and PCI cards"
 300         depends on ISA_DMA_API && WLAN_80211 && (PCI || BROKEN)
 301         select WIRELESS_EXT
 302         select CRYPTO
 303         ---help---
 304           This is the standard Linux driver to support Cisco/Aironet ISA and
 305           PCI 802.11 wireless cards.
 306           It supports the new 802.11b cards from Cisco (Cisco 34X, Cisco 35X
 307           - with or without encryption) as well as card before the Cisco
 308           acquisition (Aironet 4500, Aironet 4800, Aironet 4800B).
 309
 310           This driver support both the standard Linux Wireless Extensions
 311           and Cisco proprietary API, so both the Linux Wireless Tools and the
 312           Cisco Linux utilities can be used to configure the card.
 313
 314           The driver can be compiled as a module and will be named "airo".
 315
 316 config HERMES
 317         tristate "Hermes chipset 802.11b support (Orinoco/Prism2/Symbol)"
 318         depends on (PPC_PMAC || PCI || PCMCIA) && WLAN_80211
 319         select WIRELESS_EXT
 320         ---help---
 321           A driver for 802.11b wireless cards based on the "Hermes" or
 322           Intersil HFA384x (Prism 2) MAC controller.  This includes the vast
 323           majority of the PCMCIA 802.11b cards (which are nearly all rebadges)
 324           - except for the Cisco/Aironet cards.  Cards supported include the
 325           Apple Airport (not a PCMCIA card), WavelanIEEE/Orinoco,
 326           Cabletron/EnteraSys Roamabout, ELSA AirLancer, MELCO Buffalo, Avaya,
 327           IBM High Rate Wireless, Farralon Syyline, Samsung MagicLAN, Netgear
 328           MA401, LinkSys WPC-11, D-Link DWL-650, 3Com AirConnect, Intel
 329           IPW2011, and Symbol Spectrum24 High Rate amongst others.
 330
 331           This option includes the guts of the driver, but in order to
 332           actually use a card you will also need to enable support for PCMCIA
 333           Hermes cards, PLX9052 based PCI adaptors or the Apple Airport below.
 334
 335           You will also very likely also need the Wireless Tools in order to
 336           configure your card and that /etc/pcmcia/wireless.opts works :
 337           <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>
 338
 339 config APPLE_AIRPORT
 340         tristate "Apple Airport support (built-in)"
 341         depends on PPC_PMAC && HERMES
 342         help
 343           Say Y here to support the Airport 802.11b wireless Ethernet hardware
 344           built into the Macintosh iBook and other recent PowerPC-based
 345           Macintosh machines. This is essentially a Lucent Orinoco card with
 346           a non-standard interface.
 347
 348           This driver does not support the Airport Extreme (802.11b/g). Use
 349           the BCM43xx driver for Airport Extreme cards.
 350
 351 config PLX_HERMES
 352         tristate "Hermes in PLX9052 based PCI adaptor support (Netgear MA301 etc.)"
 353         depends on PCI && HERMES
 354         help
 355           Enable support for PCMCIA cards supported by the "Hermes" (aka
 356           orinoco) driver when used in PLX9052 based PCI adaptors.  These
 357           adaptors are not a full PCMCIA controller but act as a more limited
 358           PCI <-> PCMCIA bridge.  Several vendors sell such adaptors so that
 359           802.11b PCMCIA cards can be used in desktop machines.  The Netgear
 360           MA301 is such an adaptor.
 361
 362 config TMD_HERMES
 363         tristate "Hermes in TMD7160 based PCI adaptor support"
 364         depends on PCI && HERMES
 365         help
 366           Enable support for PCMCIA cards supported by the "Hermes" (aka
 367           orinoco) driver when used in TMD7160 based PCI adaptors.  These
 368           adaptors are not a full PCMCIA controller but act as a more limited
 369           PCI <-> PCMCIA bridge.  Several vendors sell such adaptors so that
 370           802.11b PCMCIA cards can be used in desktop machines.
 371
 372 config NORTEL_HERMES
 373         tristate "Nortel emobility PCI adaptor support"
 374         depends on PCI && HERMES
 375         help
 376           Enable support for PCMCIA cards supported by the "Hermes" (aka
 377           orinoco) driver when used in Nortel emobility PCI adaptors.  These
 378           adaptors are not full PCMCIA controllers, but act as a more limited
 379           PCI <-> PCMCIA bridge.
 380
 381 config PCI_HERMES
 382         tristate "Prism 2.5 PCI 802.11b adaptor support"
 383         depends on PCI && HERMES
 384         help
 385           Enable support for PCI and mini-PCI 802.11b wireless NICs based on
 386           the Prism 2.5 chipset.  These are true PCI cards, not the 802.11b
 387           PCMCIA cards bundled with PCI<->PCMCIA adaptors which are also
 388           common.  Some of the built-in wireless adaptors in laptops are of
 389           this variety.
 390
 391 config PCMCIA_HERMES
 392         tristate "Hermes PCMCIA card support"
 393         depends on PCMCIA && HERMES
 394         ---help---
 395           A driver for "Hermes" chipset based PCMCIA wireless adaptors, such
 396           as the Lucent WavelanIEEE/Orinoco cards and their OEM (Cabletron/
 397           EnteraSys RoamAbout 802.11, ELSA Airlancer, Melco Buffalo and
 398           others).  It should also be usable on various Prism II based cards
 399           such as the Linksys, D-Link and Farallon Skyline.  It should also
 400           work on Symbol cards such as the 3Com AirConnect and Ericsson WLAN.
 401
 402           You will very likely need the Wireless Tools in order to
 403           configure your card and that /etc/pcmcia/wireless.opts works:
 404           <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
 405
 406 config PCMCIA_SPECTRUM
 407         tristate "Symbol Spectrum24 Trilogy PCMCIA card support"
 408         depends on PCMCIA && HERMES
 409         select FW_LOADER
 410         ---help---
 411
 412           This is a driver for 802.11b cards using RAM-loadable Symbol
 413           firmware, such as Symbol Wireless Networker LA4100, CompactFlash
 414           cards by Socket Communications and Intel PRO/Wireless 2011B.
 415
 416           This driver requires firmware download on startup.  Utilities
 417           for downloading Symbol firmware are available at
 418           <http://sourceforge.net/projects/orinoco/>
 419
 420 config ATMEL
 421       tristate "Atmel at76c50x chipset  802.11b support"
 422       depends on (PCI || PCMCIA) && WLAN_80211
 423       select WIRELESS_EXT
 424       select FW_LOADER
 425       select CRC32
 426        ---help---
 427         A driver 802.11b wireless cards based on the Atmel fast-vnet
 428         chips. This driver supports standard Linux wireless extensions.
 429
 430         Many  cards based on this chipset do not have flash memory
 431         and need their firmware loaded at start-up. If yours is
 432         one of these, you will need to provide a firmware image
 433         to be loaded into the card by the driver. The Atmel
 434         firmware package can be downloaded from
 435         <http://www.thekelleys.org.uk/atmel>
 436
 437 config PCI_ATMEL
 438       tristate "Atmel at76c506 PCI cards"
 439       depends on ATMEL && PCI
 440        ---help---
 441         Enable support for PCI and mini-PCI cards containing the
 442         Atmel at76c506 chip.
 443
 444 config PCMCIA_ATMEL
 445         tristate "Atmel at76c502/at76c504 PCMCIA cards"
 446         depends on ATMEL && PCMCIA
 447         select WIRELESS_EXT
 448         select FW_LOADER
 449         select CRC32
 450         ---help---
 451           Enable support for PCMCIA cards containing the
 452           Atmel at76c502 and at76c504 chips.
 453
 454 config AIRO_CS
 455         tristate "Cisco/Aironet 34X/35X/4500/4800 PCMCIA cards"
 456         depends on PCMCIA && (BROKEN || !M32R) && WLAN_80211
 457         select WIRELESS_EXT
 458         select CRYPTO
 459         select CRYPTO_AES
 460         ---help---
 461           This is the standard Linux driver to support Cisco/Aironet PCMCIA
 462           802.11 wireless cards.  This driver is the same as the Aironet
 463           driver part of the Linux Pcmcia package.
 464           It supports the new 802.11b cards from Cisco (Cisco 34X, Cisco 35X
 465           - with or without encryption) as well as card before the Cisco
 466           acquisition (Aironet 4500, Aironet 4800, Aironet 4800B). It also
 467           supports OEM of Cisco such as the DELL TrueMobile 4800 and Xircom
 468           802.11b cards.
 469
 470           This driver support both the standard Linux Wireless Extensions
 471           and Cisco proprietary API, so both the Linux Wireless Tools and the
 472           Cisco Linux utilities can be used to configure the card.
 473
 474 config PCMCIA_WL3501
 475       tristate "Planet WL3501 PCMCIA cards"
 476       depends on EXPERIMENTAL && PCMCIA && WLAN_80211
 477       select WIRELESS_EXT
 478        ---help---
 479          A driver for WL3501 PCMCIA 802.11 wireless cards made by Planet.
 480          It has basic support for Linux wireless extensions and initial
 481          micro support for ethtool.
 482
 483 config PRISM54
 484         tristate 'Intersil Prism GT/Duette/Indigo PCI/Cardbus'
 485         depends on PCI && EXPERIMENTAL && WLAN_80211
 486         select WIRELESS_EXT
 487         select FW_LOADER
 488         ---help---
 489           Enable PCI and Cardbus support for the following chipset based cards:
 490
 491           ISL3880 - Prism GT            802.11 b/g
 492           ISL3877 - Prism Indigo        802.11 a
 493           ISL3890 - Prism Duette        802.11 a/b/g
 494
 495           For a complete list of supported cards visit <http://prism54.org>.
 496           Here is the latest confirmed list of supported cards:
 497
 498           3com OfficeConnect 11g Cardbus Card aka 3CRWE154G72 (version 1)
 499           Allnet ALL0271 PCI Card
 500           Compex WL54G Cardbus Card
 501           Corega CG-WLCB54GT Cardbus Card
 502           D-Link Air Plus Xtreme G A1 Cardbus Card aka DWL-g650
 503           I-O Data WN-G54/CB Cardbus Card
 504           Kobishi XG-300 aka Z-Com Cardbus Card
 505           Netgear WG511 Cardbus Card
 506           Ovislink WL-5400PCI PCI Card
 507           Peabird WLG-PCI PCI Card
 508           Sitecom WL-100i Cardbus Card
 509           Sitecom WL-110i PCI Card
 510           SMC2802W -    EZ Connect g 2.4GHz 54 Mbps Wireless PCI Card
 511           SMC2835W -    EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Card
 512           SMC2835W-V2 - EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Card
 513           Z-Com XG-900 PCI Card
 514           Zyxel G-100 Cardbus Card
 515
 516           If you enable this you will need a firmware file as well.
 517           You will need to copy this to /usr/lib/hotplug/firmware/isl3890.
 518           You can get this non-GPL'd firmware file from the Prism54 project page:
 519           <http://prism54.org>
 520           You will also need the /etc/hotplug/firmware.agent script from
 521           a current hotplug package.
 522
 523           Note: You need a motherboard with DMA support to use any of these cards
 524
 525           If you want to compile the driver as a module ( = code which can be
 526           inserted in and removed from the running kernel whenever you want),
 527           say M here and read <file:Documentation/kbuild/modules.txt>.
 528           The module will be called prism54.ko.
 529
 530 config USB_ZD1201
 531         tristate "USB ZD1201 based Wireless device support"
 532         depends on USB && WLAN_80211
 533         select WIRELESS_EXT
 534         select FW_LOADER
 535         ---help---
 536           Say Y if you want to use wireless LAN adapters based on the ZyDAS
 537           ZD1201 chip.
 538
 539           This driver makes the adapter appear as a normal Ethernet interface,
 540           typically on wlan0.
 541
 542           The zd1201 device requires external firmware to be loaded.
 543           This can be found at http://linux-lc100020.sourceforge.net/
 544
 545           To compile this driver as a module, choose M here: the
 546           module will be called zd1201.
 547
 548 config USB_NET_RNDIS_WLAN
 549         tristate "Wireless RNDIS USB support"
 550         depends on USB && WLAN_80211 && EXPERIMENTAL
 551         select USB_USBNET
 552         select USB_NET_CDCETHER
 553         select USB_NET_RNDIS_HOST
 554         select WIRELESS_EXT
 555         ---help---
 556           This is a driver for wireless RNDIS devices.
 557           These are USB based adapters found in devices such as:
 558
 559           Buffalo WLI-U2-KG125S
 560           U.S. Robotics USR5421
 561           Belkin F5D7051
 562           Linksys WUSB54GSv2
 563           Linksys WUSB54GSC
 564           Asus WL169gE
 565           Eminent EM4045
 566           BT Voyager 1055
 567           Linksys WUSB54GSv1
 568           U.S. Robotics USR5420
 569           BUFFALO WLI-USB-G54
 570
 571           All of these devices are based on Broadcom 4320 chip which is the
 572           only wireless RNDIS chip known to date.
 573
 574           If you choose to build a module, it'll be called rndis_wlan.
 575
 576 config RTL8180
 577         tristate "Realtek 8180/8185 PCI support"
 578         depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
 579         select EEPROM_93CX6
 580         ---help---
 581           This is a driver for RTL8180 and RTL8185 based cards.
 582           These are PCI based chips found in cards such as:
 583
 584           (RTL8185 802.11g)
 585           A-Link WL54PC
 586
 587           (RTL8180 802.11b)
 588           Belkin F5D6020 v3
 589           Belkin F5D6020 v3
 590           Dlink DWL-610
 591           Dlink DWL-510
 592           Netgear MA521
 593           Level-One WPC-0101
 594           Acer Aspire 1357 LMi
 595           VCTnet PC-11B1
 596           Ovislink AirLive WL-1120PCM
 597           Mentor WL-PCI
 598           Linksys WPC11 v4
 599           TrendNET TEW-288PI
 600           D-Link DWL-520 Rev D
 601           Repotec RP-WP7126
 602           TP-Link TL-WN250/251
 603           Zonet ZEW1000
 604           Longshine LCS-8031-R
 605           HomeLine HLW-PCC200
 606           GigaFast WF721-AEX
 607           Planet WL-3553
 608           Encore ENLWI-PCI1-NT
 609           TrendNET TEW-266PC
 610           Gigabyte GN-WLMR101
 611           Siemens-fujitsu Amilo D1840W
 612           Edimax EW-7126
 613           PheeNet WL-11PCIR
 614           Tonze PC-2100T
 615           Planet WL-8303
 616           Dlink DWL-650 v M1
 617           Edimax EW-7106
 618           Q-Tec 770WC
 619           Topcom Skyr@cer 4011b
 620           Roper FreeLan 802.11b (edition 2004)
 621           Wistron Neweb Corp CB-200B
 622           Pentagram HorNET
 623           QTec 775WC
 624           TwinMOS Booming B Series
 625           Micronet SP906BB
 626           Sweex LC700010
 627           Surecom EP-9428
 628           Safecom SWLCR-1100
 629
 630           Thanks to Realtek for their support!
 631
 632 config RTL8187
 633         tristate "Realtek 8187 USB support"
 634         depends on MAC80211 && USB && WLAN_80211 && EXPERIMENTAL
 635         select EEPROM_93CX6
 636         ---help---
 637           This is a driver for RTL8187 based cards.
 638           These are USB based chips found in cards such as:
 639
 640           Netgear WG111v2
 641
 642           Thanks to Realtek for their support!
 643
 644 config ADM8211
 645         tristate "ADMtek ADM8211 support"
 646         depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
 647         select CRC32
 648         select EEPROM_93CX6
 649         ---help---
 650           This driver is for ADM8211A, ADM8211B, and ADM8211C based cards.
 651           These are PCI/mini-PCI/Cardbus 802.11b chips found in cards such as:
 652
 653           Xterasys Cardbus XN-2411b
 654           Blitz NetWave Point PC
 655           TrendNet 221pc
 656           Belkin F5D6001
 657           SMC 2635W
 658           Linksys WPC11 v1
 659           Fiberline FL-WL-200X
 660           3com Office Connect (3CRSHPW796)
 661           Corega WLPCIB-11
 662           SMC 2602W V2 EU
 663           D-Link DWL-520 Revision C
 664
 665           However, some of these cards have been replaced with other chips
 666           like the RTL8180L (Xterasys Cardbus XN-2411b, Belkin F5D6001) or
 667           the Ralink RT2400 (SMC2635W) without a model number change.
 668
 669           Thanks to Infineon-ADMtek for their support of this driver.
 670
 671 config P54_COMMON
 672         tristate "Softmac Prism54 support"
 673         depends on MAC80211 && WLAN_80211 && FW_LOADER && EXPERIMENTAL
 674         ---help---
 675           This is common code for isl38xx based cards.
 676           This module does nothing by itself - the USB/PCI frontends
 677           also need to be enabled in order to support any devices.
 678
 679           These devices require softmac firmware which can be found at
 680           http://prism54.org/
 681
 682           If you choose to build a module, it'll be called p54common.
 683
 684 config P54_USB
 685         tristate "Prism54 USB support"
 686         depends on P54_COMMON && USB
 687         select CRC32
 688         ---help---
 689           This driver is for USB isl38xx based wireless cards.
 690           These are USB based adapters found in devices such as:
 691
 692           3COM 3CRWE254G72
 693           SMC 2862W-G
 694           Accton 802.11g WN4501 USB
 695           Siemens Gigaset USB
 696           Netgear WG121
 697           Netgear WG111
 698           Medion 40900, Roper Europe
 699           Shuttle PN15, Airvast WM168g, IOGear GWU513
 700           Linksys WUSB54G
 701           Linksys WUSB54G Portable
 702           DLink DWL-G120 Spinnaker
 703           DLink DWL-G122
 704           Belkin F5D7050 ver 1000
 705           Cohiba Proto board
 706           SMC 2862W-G version 2
 707           U.S. Robotics U5 802.11g Adapter
 708           FUJITSU E-5400 USB D1700
 709           Sagem XG703A
 710           DLink DWL-G120 Cohiba
 711           Spinnaker Proto board
 712           Linksys WUSB54AG
 713           Inventel UR054G
 714           Spinnaker DUT
 715
 716           These devices require softmac firmware which can be found at
 717           http://prism54.org/
 718
 719           If you choose to build a module, it'll be called p54usb.
 720
 721 config P54_PCI
 722         tristate "Prism54 PCI support"
 723         depends on P54_COMMON && PCI
 724         ---help---
 725           This driver is for PCI isl38xx based wireless cards.
 726           This driver supports most devices that are supported by the
 727           fullmac prism54 driver plus many devices which are not
 728           supported by the fullmac driver/firmware.
 729
 730           This driver requires softmac firmware which can be found at
 731           http://prism54.org/
 732
 733           If you choose to build a module, it'll be called p54pci.
 734
 735 config ATH5K
 736         tristate "Atheros 5xxx wireless cards support"
 737         depends on PCI && MAC80211 && WLAN_80211 && EXPERIMENTAL
 738         ---help---
 739           This module adds support for wireless adapters based on
 740           Atheros 5xxx chipset.
 741
 742           Currently the following chip versions are supported:
 743
 744           MAC: AR5211 AR5212
 745           PHY: RF5111/2111 RF5112/2112 RF5413/2413
 746
 747           This driver uses the kernel's mac80211 subsystem.
 748
 749           If you choose to build a module, it'll be called ath5k. Say M if
 750           unsure.
 751
 752 source "drivers/net/wireless/iwlwifi/Kconfig"
 753 source "drivers/net/wireless/hostap/Kconfig"
 754 source "drivers/net/wireless/bcm43xx/Kconfig"
 755 source "drivers/net/wireless/b43/Kconfig"
 756 source "drivers/net/wireless/b43legacy/Kconfig"
 757 source "drivers/net/wireless/zd1211rw/Kconfig"
 758 source "drivers/net/wireless/rt2x00/Kconfig"
 759
 760 endmenu