drivers/net/wireless/Kconfig

   1 #
   2 # Wireless LAN device configuration
   3 #
   4
   5 menu "Wireless LAN"
   6         depends on !S390
   7
   8 config WLAN_PRE80211
   9         bool "Wireless LAN (pre-802.11)"
  10         depends on NETDEVICES
  11         ---help---
  12           Say Y if you have any pre-802.11 wireless LAN hardware.
  13
  14           This option does not affect the kernel build, it only
  15           lets you choose drivers.
  16
  17 config ARLAN
  18         tristate "Aironet Arlan 655 & IC2200 DS support"
  19         depends on ISA && !64BIT && WLAN_PRE80211
  20         select WIRELESS_EXT
  21         ---help---
  22           Aironet makes Arlan, a class of wireless LAN adapters. These use the
  23           www.Telxon.com chip, which is also used on several similar cards.
  24           This driver is tested on the 655 and IC2200 series cards. Look at
  25           <http://www.ylenurme.ee/~elmer/655/> for the latest information.
  26
  27           The driver is built as two modules, arlan and arlan-proc. The latter
  28           is the /proc interface and is not needed most of time.
  29
  30           On some computers the card ends up in non-valid state after some
  31           time. Use a ping-reset script to clear it.
  32
  33 config WAVELAN
  34         tristate "AT&T/Lucent old WaveLAN & DEC RoamAbout DS ISA support"
  35         depends on ISA && WLAN_PRE80211
  36         select WIRELESS_EXT
  37         ---help---
  38           The Lucent WaveLAN (formerly NCR and AT&T; or DEC RoamAbout DS) is
  39           a Radio LAN (wireless Ethernet-like Local Area Network) using the
  40           radio frequencies 900 MHz and 2.4 GHz.
  41
  42           If you want to use an ISA WaveLAN card under Linux, say Y and read
  43           the Ethernet-HOWTO, available from
  44           <http://www.tldp.org/docs.html#howto>. Some more specific
  45           information is contained in
  46           <file:Documentation/networking/wavelan.txt> and in the source code
  47           <file:drivers/net/wireless/wavelan.p.h>.
  48
  49           You will also need the wireless tools package available from
  50           <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
  51           Please read the man pages contained therein.
  52
  53           To compile this driver as a module, choose M here: the module will be
  54           called wavelan.
  55
  56 config PCMCIA_WAVELAN
  57         tristate "AT&T/Lucent old WaveLAN Pcmcia wireless support"
  58         depends on PCMCIA && WLAN_PRE80211
  59         select WIRELESS_EXT
  60         help
  61           Say Y here if you intend to attach an AT&T/Lucent Wavelan PCMCIA
  62           (PC-card) wireless Ethernet networking card to your computer.  This
  63           driver is for the non-IEEE-802.11 Wavelan cards.
  64
  65           To compile this driver as a module, choose M here: the module will be
  66           called wavelan_cs.  If unsure, say N.
  67
  68 config PCMCIA_NETWAVE
  69         tristate "Xircom Netwave AirSurfer Pcmcia wireless support"
  70         depends on PCMCIA && WLAN_PRE80211
  71         select WIRELESS_EXT
  72         help
  73           Say Y here if you intend to attach this type of PCMCIA (PC-card)
  74           wireless Ethernet networking card to your computer.
  75
  76           To compile this driver as a module, choose M here: the module will be
  77           called netwave_cs.  If unsure, say N.
  78
  79
  80 config WLAN_80211
  81         bool "Wireless LAN (IEEE 802.11)"
  82         depends on NETDEVICES
  83         ---help---
  84           Say Y if you have any 802.11 wireless LAN hardware.
  85
  86           This option does not affect the kernel build, it only
  87           lets you choose drivers.
  88
  89 config PCMCIA_RAYCS
  90         tristate "Aviator/Raytheon 2.4MHz wireless support"
  91         depends on PCMCIA && WLAN_80211
  92         select WIRELESS_EXT
  93         ---help---
  94           Say Y here if you intend to attach an Aviator/Raytheon PCMCIA
  95           (PC-card) wireless Ethernet networking card to your computer.
  96           Please read the file <file:Documentation/networking/ray_cs.txt> for
  97           details.
  98
  99           To compile this driver as a module, choose M here: the module will be
 100           called ray_cs.  If unsure, say N.
 101
 102 config IPW2100
 103         tristate "Intel PRO/Wireless 2100 Network Connection"
 104         depends on PCI && WLAN_80211
 105         select WIRELESS_EXT
 106         select FW_LOADER
 107         select IEEE80211
 108         ---help---
 109           A driver for the Intel PRO/Wireless 2100 Network
 110           Connection 802.11b wireless network adapter.
 111
 112           See <file:Documentation/networking/README.ipw2100> for information on
 113           the capabilities currently enabled in this driver and for tips
 114           for debugging issues and problems.
 115
 116           In order to use this driver, you will need a firmware image for it.
 117           You can obtain the firmware from
 118           <http://ipw2100.sf.net/>.  Once you have the firmware image, you
 119           will need to place it in /lib/firmware.
 120
 121           You will also very likely need the Wireless Tools in order to
 122           configure your card:
 123
 124           <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
 125
 126           It is recommended that you compile this driver as a module (M)
 127           rather than built-in (Y). This driver requires firmware at device
 128           initialization time, and when built-in this typically happens
 129           before the filesystem is accessible (hence firmware will be
 130           unavailable and initialization will fail). If you do choose to build
 131           this driver into your kernel image, you can avoid this problem by
 132           including the firmware and a firmware loader in an initramfs.
 133
 134 config IPW2100_MONITOR
 135         bool "Enable promiscuous mode"
 136         depends on IPW2100
 137         ---help---
 138           Enables promiscuous/monitor mode support for the ipw2100 driver.
 139           With this feature compiled into the driver, you can switch to
 140           promiscuous mode via the Wireless Tool's Monitor mode.  While in this
 141           mode, no packets can be sent.
 142
 143 config IPW2100_DEBUG
 144         bool "Enable full debugging output in IPW2100 module."
 145         depends on IPW2100
 146         ---help---
 147           This option will enable debug tracing output for the IPW2100.
 148
 149           This will result in the kernel module being ~60k larger.  You can
 150           control which debug output is sent to the kernel log by setting the
 151           value in
 152
 153           /sys/bus/pci/drivers/ipw2100/debug_level
 154
 155           This entry will only exist if this option is enabled.
 156
 157           If you are not trying to debug or develop the IPW2100 driver, you
 158           most likely want to say N here.
 159
 160 config IPW2200
 161         tristate "Intel PRO/Wireless 2200BG and 2915ABG Network Connection"
 162         depends on PCI && WLAN_80211
 163         select WIRELESS_EXT
 164         select FW_LOADER
 165         select IEEE80211
 166         ---help---
 167           A driver for the Intel PRO/Wireless 2200BG and 2915ABG Network
 168           Connection adapters.
 169
 170           See <file:Documentation/networking/README.ipw2200> for
 171           information on the capabilities currently enabled in this
 172           driver and for tips for debugging issues and problems.
 173
 174           In order to use this driver, you will need a firmware image for it.
 175           You can obtain the firmware from
 176           <http://ipw2200.sf.net/>.  See the above referenced README.ipw2200
 177           for information on where to install the firmware images.
 178
 179           You will also very likely need the Wireless Tools in order to
 180           configure your card:
 181
 182           <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
 183
 184           It is recommended that you compile this driver as a module (M)
 185           rather than built-in (Y). This driver requires firmware at device
 186           initialization time, and when built-in this typically happens
 187           before the filesystem is accessible (hence firmware will be
 188           unavailable and initialization will fail). If you do choose to build
 189           this driver into your kernel image, you can avoid this problem by
 190           including the firmware and a firmware loader in an initramfs.
 191
 192 config IPW2200_MONITOR
 193         bool "Enable promiscuous mode"
 194         depends on IPW2200
 195         ---help---
 196           Enables promiscuous/monitor mode support for the ipw2200 driver.
 197           With this feature compiled into the driver, you can switch to
 198           promiscuous mode via the Wireless Tool's Monitor mode.  While in this
 199           mode, no packets can be sent.
 200
 201 config IPW2200_RADIOTAP
 202         bool "Enable radiotap format 802.11 raw packet support"
 203         depends on IPW2200_MONITOR
 204
 205 config IPW2200_PROMISCUOUS
 206         bool "Enable creation of a RF radiotap promiscuous interface"
 207         depends on IPW2200_MONITOR
 208         select IPW2200_RADIOTAP
 209         ---help---
 210           Enables the creation of a second interface prefixed 'rtap'.
 211           This second interface will provide every received in radiotap
 212           format.
 213
 214           This is useful for performing wireless network analysis while
 215           maintaining an active association.
 216
 217           Example usage:
 218
 219             % modprobe ipw2200 rtap_iface=1
 220             % ifconfig rtap0 up
 221             % tethereal -i rtap0
 222
 223           If you do not specify 'rtap_iface=1' as a module parameter then
 224           the rtap interface will not be created and you will need to turn
 225           it on via sysfs:
 226
 227             % echo 1 > /sys/bus/pci/drivers/ipw2200/*/rtap_iface
 228
 229 config IPW2200_QOS
 230         bool "Enable QoS support"
 231         depends on IPW2200 && EXPERIMENTAL
 232
 233 config IPW2200_DEBUG
 234         bool "Enable full debugging output in IPW2200 module."
 235         depends on IPW2200
 236         ---help---
 237           This option will enable low level debug tracing output for IPW2200.
 238
 239           Note, normal debug code is already compiled in. This low level
 240           debug option enables debug on hot paths (e.g Tx, Rx, ISR) and
 241           will result in the kernel module being ~70 larger.  Most users
 242           will typically not need this high verbosity debug information.
 243
 244           If you are not sure, say N here.
 245
 246 config LIBERTAS
 247         tristate "Marvell 8xxx Libertas WLAN driver support"
 248         depends on WLAN_80211
 249         select WIRELESS_EXT
 250         select FW_LOADER
 251         ---help---
 252           A library for Marvell Libertas 8xxx devices.
 253
 254 config LIBERTAS_USB
 255         tristate "Marvell Libertas 8388 USB 802.11b/g cards"
 256         depends on LIBERTAS && USB
 257         ---help---
 258           A driver for Marvell Libertas 8388 USB devices.
 259
 260 config LIBERTAS_CS
 261         tristate "Marvell Libertas 8385 CompactFlash 802.11b/g cards"
 262         depends on LIBERTAS && PCMCIA
 263         select FW_LOADER
 264         ---help---
 265           A driver for Marvell Libertas 8385 CompactFlash devices.
 266
 267 config LIBERTAS_SDIO
 268         tristate "Marvell Libertas 8385 and 8686 SDIO 802.11b/g cards"
 269         depends on LIBERTAS && MMC
 270         ---help---
 271           A driver for Marvell Libertas 8385 and 8686 SDIO devices.
 272
 273 config LIBERTAS_DEBUG
 274         bool "Enable full debugging output in the Libertas module."
 275         depends on LIBERTAS
 276         ---help---
 277           Debugging support.
 278
 279 config AIRO
 280         tristate "Cisco/Aironet 34X/35X/4500/4800 ISA and PCI cards"
 281         depends on ISA_DMA_API && WLAN_80211 && (PCI || BROKEN)
 282         select WIRELESS_EXT
 283         select CRYPTO
 284         ---help---
 285           This is the standard Linux driver to support Cisco/Aironet ISA and
 286           PCI 802.11 wireless cards.
 287           It supports the new 802.11b cards from Cisco (Cisco 34X, Cisco 35X
 288           - with or without encryption) as well as card before the Cisco
 289           acquisition (Aironet 4500, Aironet 4800, Aironet 4800B).
 290
 291           This driver support both the standard Linux Wireless Extensions
 292           and Cisco proprietary API, so both the Linux Wireless Tools and the
 293           Cisco Linux utilities can be used to configure the card.
 294
 295           The driver can be compiled as a module and will be named "airo".
 296
 297 config HERMES
 298         tristate "Hermes chipset 802.11b support (Orinoco/Prism2/Symbol)"
 299         depends on (PPC_PMAC || PCI || PCMCIA) && WLAN_80211
 300         select WIRELESS_EXT
 301         ---help---
 302           A driver for 802.11b wireless cards based on the "Hermes" or
 303           Intersil HFA384x (Prism 2) MAC controller.  This includes the vast
 304           majority of the PCMCIA 802.11b cards (which are nearly all rebadges)
 305           - except for the Cisco/Aironet cards.  Cards supported include the
 306           Apple Airport (not a PCMCIA card), WavelanIEEE/Orinoco,
 307           Cabletron/EnteraSys Roamabout, ELSA AirLancer, MELCO Buffalo, Avaya,
 308           IBM High Rate Wireless, Farralon Syyline, Samsung MagicLAN, Netgear
 309           MA401, LinkSys WPC-11, D-Link DWL-650, 3Com AirConnect, Intel
 310           IPW2011, and Symbol Spectrum24 High Rate amongst others.
 311
 312           This option includes the guts of the driver, but in order to
 313           actually use a card you will also need to enable support for PCMCIA
 314           Hermes cards, PLX9052 based PCI adaptors or the Apple Airport below.
 315
 316           You will also very likely also need the Wireless Tools in order to
 317           configure your card and that /etc/pcmcia/wireless.opts works :
 318           <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>
 319
 320 config APPLE_AIRPORT
 321         tristate "Apple Airport support (built-in)"
 322         depends on PPC_PMAC && HERMES
 323         help
 324           Say Y here to support the Airport 802.11b wireless Ethernet hardware
 325           built into the Macintosh iBook and other recent PowerPC-based
 326           Macintosh machines. This is essentially a Lucent Orinoco card with
 327           a non-standard interface.
 328
 329           This driver does not support the Airport Extreme (802.11b/g). Use
 330           the BCM43xx driver for Airport Extreme cards.
 331
 332 config PLX_HERMES
 333         tristate "Hermes in PLX9052 based PCI adaptor support (Netgear MA301 etc.)"
 334         depends on PCI && HERMES
 335         help
 336           Enable support for PCMCIA cards supported by the "Hermes" (aka
 337           orinoco) driver when used in PLX9052 based PCI adaptors.  These
 338           adaptors are not a full PCMCIA controller but act as a more limited
 339           PCI <-> PCMCIA bridge.  Several vendors sell such adaptors so that
 340           802.11b PCMCIA cards can be used in desktop machines.  The Netgear
 341           MA301 is such an adaptor.
 342
 343 config TMD_HERMES
 344         tristate "Hermes in TMD7160 based PCI adaptor support"
 345         depends on PCI && HERMES
 346         help
 347           Enable support for PCMCIA cards supported by the "Hermes" (aka
 348           orinoco) driver when used in TMD7160 based PCI adaptors.  These
 349           adaptors are not a full PCMCIA controller but act as a more limited
 350           PCI <-> PCMCIA bridge.  Several vendors sell such adaptors so that
 351           802.11b PCMCIA cards can be used in desktop machines.
 352
 353 config NORTEL_HERMES
 354         tristate "Nortel emobility PCI adaptor support"
 355         depends on PCI && HERMES
 356         help
 357           Enable support for PCMCIA cards supported by the "Hermes" (aka
 358           orinoco) driver when used in Nortel emobility PCI adaptors.  These
 359           adaptors are not full PCMCIA controllers, but act as a more limited
 360           PCI <-> PCMCIA bridge.
 361
 362 config PCI_HERMES
 363         tristate "Prism 2.5 PCI 802.11b adaptor support"
 364         depends on PCI && HERMES
 365         help
 366           Enable support for PCI and mini-PCI 802.11b wireless NICs based on
 367           the Prism 2.5 chipset.  These are true PCI cards, not the 802.11b
 368           PCMCIA cards bundled with PCI<->PCMCIA adaptors which are also
 369           common.  Some of the built-in wireless adaptors in laptops are of
 370           this variety.
 371
 372 config PCMCIA_HERMES
 373         tristate "Hermes PCMCIA card support"
 374         depends on PCMCIA && HERMES
 375         ---help---
 376           A driver for "Hermes" chipset based PCMCIA wireless adaptors, such
 377           as the Lucent WavelanIEEE/Orinoco cards and their OEM (Cabletron/
 378           EnteraSys RoamAbout 802.11, ELSA Airlancer, Melco Buffalo and
 379           others).  It should also be usable on various Prism II based cards
 380           such as the Linksys, D-Link and Farallon Skyline.  It should also
 381           work on Symbol cards such as the 3Com AirConnect and Ericsson WLAN.
 382
 383           You will very likely need the Wireless Tools in order to
 384           configure your card and that /etc/pcmcia/wireless.opts works:
 385           <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
 386
 387 config PCMCIA_SPECTRUM
 388         tristate "Symbol Spectrum24 Trilogy PCMCIA card support"
 389         depends on PCMCIA && HERMES
 390         select FW_LOADER
 391         ---help---
 392
 393           This is a driver for 802.11b cards using RAM-loadable Symbol
 394           firmware, such as Symbol Wireless Networker LA4100, CompactFlash
 395           cards by Socket Communications and Intel PRO/Wireless 2011B.
 396
 397           This driver requires firmware download on startup.  Utilities
 398           for downloading Symbol firmware are available at
 399           <http://sourceforge.net/projects/orinoco/>
 400
 401 config ATMEL
 402       tristate "Atmel at76c50x chipset  802.11b support"
 403       depends on (PCI || PCMCIA) && WLAN_80211
 404       select WIRELESS_EXT
 405       select FW_LOADER
 406       select CRC32
 407        ---help---
 408         A driver 802.11b wireless cards based on the Atmel fast-vnet
 409         chips. This driver supports standard Linux wireless extensions.
 410
 411         Many  cards based on this chipset do not have flash memory
 412         and need their firmware loaded at start-up. If yours is
 413         one of these, you will need to provide a firmware image
 414         to be loaded into the card by the driver. The Atmel
 415         firmware package can be downloaded from
 416         <http://www.thekelleys.org.uk/atmel>
 417
 418 config PCI_ATMEL
 419       tristate "Atmel at76c506 PCI cards"
 420       depends on ATMEL && PCI
 421        ---help---
 422         Enable support for PCI and mini-PCI cards containing the
 423         Atmel at76c506 chip.
 424
 425 config PCMCIA_ATMEL
 426         tristate "Atmel at76c502/at76c504 PCMCIA cards"
 427         depends on ATMEL && PCMCIA
 428         select WIRELESS_EXT
 429         select FW_LOADER
 430         select CRC32
 431         ---help---
 432           Enable support for PCMCIA cards containing the
 433           Atmel at76c502 and at76c504 chips.
 434
 435 config AIRO_CS
 436         tristate "Cisco/Aironet 34X/35X/4500/4800 PCMCIA cards"
 437         depends on PCMCIA && (BROKEN || !M32R) && WLAN_80211
 438         select WIRELESS_EXT
 439         select CRYPTO
 440         select CRYPTO_AES
 441         ---help---
 442           This is the standard Linux driver to support Cisco/Aironet PCMCIA
 443           802.11 wireless cards.  This driver is the same as the Aironet
 444           driver part of the Linux Pcmcia package.
 445           It supports the new 802.11b cards from Cisco (Cisco 34X, Cisco 35X
 446           - with or without encryption) as well as card before the Cisco
 447           acquisition (Aironet 4500, Aironet 4800, Aironet 4800B). It also
 448           supports OEM of Cisco such as the DELL TrueMobile 4800 and Xircom
 449           802.11b cards.
 450
 451           This driver support both the standard Linux Wireless Extensions
 452           and Cisco proprietary API, so both the Linux Wireless Tools and the
 453           Cisco Linux utilities can be used to configure the card.
 454
 455 config PCMCIA_WL3501
 456       tristate "Planet WL3501 PCMCIA cards"
 457       depends on EXPERIMENTAL && PCMCIA && WLAN_80211
 458       select WIRELESS_EXT
 459        ---help---
 460          A driver for WL3501 PCMCIA 802.11 wireless cards made by Planet.
 461          It has basic support for Linux wireless extensions and initial
 462          micro support for ethtool.
 463
 464 config PRISM54
 465         tristate 'Intersil Prism GT/Duette/Indigo PCI/Cardbus'
 466         depends on PCI && EXPERIMENTAL && WLAN_80211
 467         select WIRELESS_EXT
 468         select FW_LOADER
 469         ---help---
 470           Enable PCI and Cardbus support for the following chipset based cards:
 471
 472           ISL3880 - Prism GT            802.11 b/g
 473           ISL3877 - Prism Indigo        802.11 a
 474           ISL3890 - Prism Duette        802.11 a/b/g
 475
 476           For a complete list of supported cards visit <http://prism54.org>.
 477           Here is the latest confirmed list of supported cards:
 478
 479           3com OfficeConnect 11g Cardbus Card aka 3CRWE154G72 (version 1)
 480           Allnet ALL0271 PCI Card
 481           Compex WL54G Cardbus Card
 482           Corega CG-WLCB54GT Cardbus Card
 483           D-Link Air Plus Xtreme G A1 Cardbus Card aka DWL-g650
 484           I-O Data WN-G54/CB Cardbus Card
 485           Kobishi XG-300 aka Z-Com Cardbus Card
 486           Netgear WG511 Cardbus Card
 487           Ovislink WL-5400PCI PCI Card
 488           Peabird WLG-PCI PCI Card
 489           Sitecom WL-100i Cardbus Card
 490           Sitecom WL-110i PCI Card
 491           SMC2802W -    EZ Connect g 2.4GHz 54 Mbps Wireless PCI Card
 492           SMC2835W -    EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Card
 493           SMC2835W-V2 - EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Card
 494           Z-Com XG-900 PCI Card
 495           Zyxel G-100 Cardbus Card
 496
 497           If you enable this you will need a firmware file as well.
 498           You will need to copy this to /usr/lib/hotplug/firmware/isl3890.
 499           You can get this non-GPL'd firmware file from the Prism54 project page:
 500           <http://prism54.org>
 501           You will also need the /etc/hotplug/firmware.agent script from
 502           a current hotplug package.
 503
 504           Note: You need a motherboard with DMA support to use any of these cards
 505
 506           If you want to compile the driver as a module ( = code which can be
 507           inserted in and removed from the running kernel whenever you want),
 508           say M here and read <file:Documentation/kbuild/modules.txt>.
 509           The module will be called prism54.ko.
 510
 511 config USB_ZD1201
 512         tristate "USB ZD1201 based Wireless device support"
 513         depends on USB && WLAN_80211
 514         select WIRELESS_EXT
 515         select FW_LOADER
 516         ---help---
 517           Say Y if you want to use wireless LAN adapters based on the ZyDAS
 518           ZD1201 chip.
 519
 520           This driver makes the adapter appear as a normal Ethernet interface,
 521           typically on wlan0.
 522
 523           The zd1201 device requires external firmware to be loaded.
 524           This can be found at http://linux-lc100020.sourceforge.net/
 525
 526           To compile this driver as a module, choose M here: the
 527           module will be called zd1201.
 528
 529 config USB_NET_RNDIS_WLAN
 530         tristate "Wireless RNDIS USB support"
 531         depends on USB && WLAN_80211 && EXPERIMENTAL
 532         select USB_USBNET
 533         select USB_NET_CDCETHER
 534         select USB_NET_RNDIS_HOST
 535         select WIRELESS_EXT
 536         ---help---
 537           This is a driver for wireless RNDIS devices.
 538           These are USB based adapters found in devices such as:
 539
 540           Buffalo WLI-U2-KG125S
 541           U.S. Robotics USR5421
 542           Belkin F5D7051
 543           Linksys WUSB54GSv2
 544           Linksys WUSB54GSC
 545           Asus WL169gE
 546           Eminent EM4045
 547           BT Voyager 1055
 548           Linksys WUSB54GSv1
 549           U.S. Robotics USR5420
 550           BUFFALO WLI-USB-G54
 551
 552           All of these devices are based on Broadcom 4320 chip which is the
 553           only wireless RNDIS chip known to date.
 554
 555           If you choose to build a module, it'll be called rndis_wlan.
 556
 557 config RTL8180
 558         tristate "Realtek 8180/8185 PCI support"
 559         depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
 560         select EEPROM_93CX6
 561         ---help---
 562           This is a driver for RTL8180 and RTL8185 based cards.
 563           These are PCI based chips found in cards such as:
 564
 565           (RTL8185 802.11g)
 566           A-Link WL54PC
 567
 568           (RTL8180 802.11b)
 569           Belkin F5D6020 v3
 570           Belkin F5D6020 v3
 571           Dlink DWL-610
 572           Dlink DWL-510
 573           Netgear MA521
 574           Level-One WPC-0101
 575           Acer Aspire 1357 LMi
 576           VCTnet PC-11B1
 577           Ovislink AirLive WL-1120PCM
 578           Mentor WL-PCI
 579           Linksys WPC11 v4
 580           TrendNET TEW-288PI
 581           D-Link DWL-520 Rev D
 582           Repotec RP-WP7126
 583           TP-Link TL-WN250/251
 584           Zonet ZEW1000
 585           Longshine LCS-8031-R
 586           HomeLine HLW-PCC200
 587           GigaFast WF721-AEX
 588           Planet WL-3553
 589           Encore ENLWI-PCI1-NT
 590           TrendNET TEW-266PC
 591           Gigabyte GN-WLMR101
 592           Siemens-fujitsu Amilo D1840W
 593           Edimax EW-7126
 594           PheeNet WL-11PCIR
 595           Tonze PC-2100T
 596           Planet WL-8303
 597           Dlink DWL-650 v M1
 598           Edimax EW-7106
 599           Q-Tec 770WC
 600           Topcom Skyr@cer 4011b
 601           Roper FreeLan 802.11b (edition 2004)
 602           Wistron Neweb Corp CB-200B
 603           Pentagram HorNET
 604           QTec 775WC
 605           TwinMOS Booming B Series
 606           Micronet SP906BB
 607           Sweex LC700010
 608           Surecom EP-9428
 609           Safecom SWLCR-1100
 610
 611           Thanks to Realtek for their support!
 612
 613 config RTL8187
 614         tristate "Realtek 8187 and 8187B USB support"
 615         depends on MAC80211 && USB && WLAN_80211 && EXPERIMENTAL
 616         select EEPROM_93CX6
 617         ---help---
 618           This is a driver for RTL8187 and RTL8187B based cards.
 619           These are USB based chips found in devices such as:
 620
 621           Netgear WG111v2
 622           Level 1 WNC-0301USB
 623           Micronet SP907GK V5
 624           Encore ENUWI-G2
 625           Trendnet TEW-424UB
 626           ASUS P5B Deluxe
 627           Toshiba Satellite Pro series of laptops
 628
 629           Thanks to Realtek for their support!
 630
 631 config ADM8211
 632         tristate "ADMtek ADM8211 support"
 633         depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
 634         select CRC32
 635         select EEPROM_93CX6
 636         ---help---
 637           This driver is for ADM8211A, ADM8211B, and ADM8211C based cards.
 638           These are PCI/mini-PCI/Cardbus 802.11b chips found in cards such as:
 639
 640           Xterasys Cardbus XN-2411b
 641           Blitz NetWave Point PC
 642           TrendNet 221pc
 643           Belkin F5D6001
 644           SMC 2635W
 645           Linksys WPC11 v1
 646           Fiberline FL-WL-200X
 647           3com Office Connect (3CRSHPW796)
 648           Corega WLPCIB-11
 649           SMC 2602W V2 EU
 650           D-Link DWL-520 Revision C
 651
 652           However, some of these cards have been replaced with other chips
 653           like the RTL8180L (Xterasys Cardbus XN-2411b, Belkin F5D6001) or
 654           the Ralink RT2400 (SMC2635W) without a model number change.
 655
 656           Thanks to Infineon-ADMtek for their support of this driver.
 657
 658 config MAC80211_HWSIM
 659         tristate "Simulated radio testing tool for mac80211"
 660         depends on MAC80211 && WLAN_80211
 661         ---help---
 662           This driver is a developer testing tool that can be used to test
 663           IEEE 802.11 networking stack (mac80211) functionality. This is not
 664           needed for normal wireless LAN usage and is only for testing. See
 665           Documentation/networking/mac80211_hwsim for more information on how
 666           to use this tool.
 667
 668           To compile this driver as a module, choose M here: the module will be
 669           called mac80211_hwsim.  If unsure, say N.
 670
 671 source "drivers/net/wireless/p54/Kconfig"
 672 source "drivers/net/wireless/ath5k/Kconfig"
 673 source "drivers/net/wireless/iwlwifi/Kconfig"
 674 source "drivers/net/wireless/hostap/Kconfig"
 675 source "drivers/net/wireless/b43/Kconfig"
 676 source "drivers/net/wireless/b43legacy/Kconfig"
 677 source "drivers/net/wireless/zd1211rw/Kconfig"
 678 source "drivers/net/wireless/rt2x00/Kconfig"
 679
 680 endmenu