drivers/net/wireless/Kconfig

   1 #
   2 # Wireless LAN device configuration
   3 #
   4
   5 menu "Wireless LAN"
   6         depends on !S390
   7
   8 config WLAN_PRE80211
   9         bool "Wireless LAN (pre-802.11)"
  10         depends on NETDEVICES
  11         ---help---
  12           Say Y if you have any pre-802.11 wireless LAN hardware.
  13
  14           This option does not affect the kernel build, it only
  15           lets you choose drivers.
  16
  17 config STRIP
  18         tristate "STRIP (Metricom starmode radio IP)"
  19         depends on INET && WLAN_PRE80211
  20         select WIRELESS_EXT
  21         ---help---
  22           Say Y if you have a Metricom radio and intend to use Starmode Radio
  23           IP. STRIP is a radio protocol developed for the MosquitoNet project
  24           (on the WWW at <http://mosquitonet.stanford.edu/>) to send Internet
  25           traffic using Metricom radios.  Metricom radios are small, battery
  26           powered, 100kbit/sec packet radio transceivers, about the size and
  27           weight of a cellular telephone. (You may also have heard them called
  28           "Metricom modems" but we avoid the term "modem" because it misleads
  29           many people into thinking that you can plug a Metricom modem into a
  30           phone line and use it as a modem.)
  31
  32           You can use STRIP on any Linux machine with a serial port, although
  33           it is obviously most useful for people with laptop computers. If you
  34           think you might get a Metricom radio in the future, there is no harm
  35           in saying Y to STRIP now, except that it makes the kernel a bit
  36           bigger.
  37
  38           To compile this as a module, choose M here: the module will be
  39           called strip.
  40
  41 config ARLAN
  42         tristate "Aironet Arlan 655 & IC2200 DS support"
  43         depends on ISA && !64BIT && WLAN_PRE80211
  44         select WIRELESS_EXT
  45         ---help---
  46           Aironet makes Arlan, a class of wireless LAN adapters. These use the
  47           www.Telxon.com chip, which is also used on several similar cards.
  48           This driver is tested on the 655 and IC2200 series cards. Look at
  49           <http://www.ylenurme.ee/~elmer/655/> for the latest information.
  50
  51           The driver is built as two modules, arlan and arlan-proc. The latter
  52           is the /proc interface and is not needed most of time.
  53
  54           On some computers the card ends up in non-valid state after some
  55           time. Use a ping-reset script to clear it.
  56
  57 config WAVELAN
  58         tristate "AT&T/Lucent old WaveLAN & DEC RoamAbout DS ISA support"
  59         depends on ISA && WLAN_PRE80211
  60         select WIRELESS_EXT
  61         ---help---
  62           The Lucent WaveLAN (formerly NCR and AT&T; or DEC RoamAbout DS) is
  63           a Radio LAN (wireless Ethernet-like Local Area Network) using the
  64           radio frequencies 900 MHz and 2.4 GHz.
  65
  66           If you want to use an ISA WaveLAN card under Linux, say Y and read
  67           the Ethernet-HOWTO, available from
  68           <http://www.tldp.org/docs.html#howto>. Some more specific
  69           information is contained in
  70           <file:Documentation/networking/wavelan.txt> and in the source code
  71           <file:drivers/net/wireless/wavelan.p.h>.
  72
  73           You will also need the wireless tools package available from
  74           <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.
  75           Please read the man pages contained therein.
  76
  77           To compile this driver as a module, choose M here: the module will be
  78           called wavelan.
  79
  80 config PCMCIA_WAVELAN
  81         tristate "AT&T/Lucent old WaveLAN Pcmcia wireless support"
  82         depends on PCMCIA && WLAN_PRE80211
  83         select WIRELESS_EXT
  84         help
  85           Say Y here if you intend to attach an AT&T/Lucent Wavelan PCMCIA
  86           (PC-card) wireless Ethernet networking card to your computer.  This
  87           driver is for the non-IEEE-802.11 Wavelan cards.
  88
  89           To compile this driver as a module, choose M here: the module will be
  90           called wavelan_cs.  If unsure, say N.
  91
  92 config PCMCIA_NETWAVE
  93         tristate "Xircom Netwave AirSurfer Pcmcia wireless support"
  94         depends on PCMCIA && WLAN_PRE80211
  95         select WIRELESS_EXT
  96         help
  97           Say Y here if you intend to attach this type of PCMCIA (PC-card)
  98           wireless Ethernet networking card to your computer.
  99
 100           To compile this driver as a module, choose M here: the module will be
 101           called netwave_cs.  If unsure, say N.
 102
 103
 104 config WLAN_80211
 105         bool "Wireless LAN (IEEE 802.11)"
 106         depends on NETDEVICES
 107         ---help---
 108           Say Y if you have any 802.11 wireless LAN hardware.
 109
 110           This option does not affect the kernel build, it only
 111           lets you choose drivers.
 112
 113 config PCMCIA_RAYCS
 114         tristate "Aviator/Raytheon 2.4GHz wireless support"
 115         depends on PCMCIA && WLAN_80211
 116         select WIRELESS_EXT
 117         ---help---
 118           Say Y here if you intend to attach an Aviator/Raytheon PCMCIA
 119           (PC-card) wireless Ethernet networking card to your computer.
 120           Please read the file <file:Documentation/networking/ray_cs.txt> for
 121           details.
 122
 123           To compile this driver as a module, choose M here: the module will be
 124           called ray_cs.  If unsure, say N.
 125
 126 config LIBERTAS
 127         tristate "Marvell 8xxx Libertas WLAN driver support"
 128         depends on WLAN_80211
 129         select WIRELESS_EXT
 130         select LIB80211
 131         select FW_LOADER
 132         ---help---
 133           A library for Marvell Libertas 8xxx devices.
 134
 135 config LIBERTAS_USB
 136         tristate "Marvell Libertas 8388 USB 802.11b/g cards"
 137         depends on LIBERTAS && USB
 138         ---help---
 139           A driver for Marvell Libertas 8388 USB devices.
 140
 141 config LIBERTAS_CS
 142         tristate "Marvell Libertas 8385 CompactFlash 802.11b/g cards"
 143         depends on LIBERTAS && PCMCIA
 144         select FW_LOADER
 145         ---help---
 146           A driver for Marvell Libertas 8385 CompactFlash devices.
 147
 148 config LIBERTAS_SDIO
 149         tristate "Marvell Libertas 8385/8686/8688 SDIO 802.11b/g cards"
 150         depends on LIBERTAS && MMC
 151         ---help---
 152           A driver for Marvell Libertas 8385/8686/8688 SDIO devices.
 153
 154 config LIBERTAS_SPI
 155         tristate "Marvell Libertas 8686 SPI 802.11b/g cards"
 156         depends on LIBERTAS && SPI
 157         ---help---
 158           A driver for Marvell Libertas 8686 SPI devices.
 159
 160 config LIBERTAS_DEBUG
 161         bool "Enable full debugging output in the Libertas module."
 162         depends on LIBERTAS
 163         ---help---
 164           Debugging support.
 165
 166 config LIBERTAS_THINFIRM
 167         tristate "Marvell 8xxx Libertas WLAN driver support with thin firmware"
 168         depends on WLAN_80211 && MAC80211
 169         select FW_LOADER
 170         ---help---
 171           A library for Marvell Libertas 8xxx devices using thinfirm.
 172
 173 config LIBERTAS_THINFIRM_USB
 174         tristate "Marvell Libertas 8388 USB 802.11b/g cards with thin firmware"
 175         depends on LIBERTAS_THINFIRM && USB
 176         ---help---
 177           A driver for Marvell Libertas 8388 USB devices using thinfirm.
 178
 179 config AIRO
 180         tristate "Cisco/Aironet 34X/35X/4500/4800 ISA and PCI cards"
 181         depends on ISA_DMA_API && WLAN_80211 && (PCI || BROKEN)
 182         select WIRELESS_EXT
 183         select CRYPTO
 184         ---help---
 185           This is the standard Linux driver to support Cisco/Aironet ISA and
 186           PCI 802.11 wireless cards.
 187           It supports the new 802.11b cards from Cisco (Cisco 34X, Cisco 35X
 188           - with or without encryption) as well as card before the Cisco
 189           acquisition (Aironet 4500, Aironet 4800, Aironet 4800B).
 190
 191           This driver support both the standard Linux Wireless Extensions
 192           and Cisco proprietary API, so both the Linux Wireless Tools and the
 193           Cisco Linux utilities can be used to configure the card.
 194
 195           The driver can be compiled as a module and will be named "airo".
 196
 197 config ATMEL
 198       tristate "Atmel at76c50x chipset  802.11b support"
 199       depends on (PCI || PCMCIA) && WLAN_80211
 200       select WIRELESS_EXT
 201       select FW_LOADER
 202       select CRC32
 203        ---help---
 204         A driver 802.11b wireless cards based on the Atmel fast-vnet
 205         chips. This driver supports standard Linux wireless extensions.
 206
 207         Many  cards based on this chipset do not have flash memory
 208         and need their firmware loaded at start-up. If yours is
 209         one of these, you will need to provide a firmware image
 210         to be loaded into the card by the driver. The Atmel
 211         firmware package can be downloaded from
 212         <http://www.thekelleys.org.uk/atmel>
 213
 214 config PCI_ATMEL
 215       tristate "Atmel at76c506 PCI cards"
 216       depends on ATMEL && PCI
 217        ---help---
 218         Enable support for PCI and mini-PCI cards containing the
 219         Atmel at76c506 chip.
 220
 221 config PCMCIA_ATMEL
 222         tristate "Atmel at76c502/at76c504 PCMCIA cards"
 223         depends on ATMEL && PCMCIA
 224         select WIRELESS_EXT
 225         select FW_LOADER
 226         select CRC32
 227         ---help---
 228           Enable support for PCMCIA cards containing the
 229           Atmel at76c502 and at76c504 chips.
 230
 231 config AT76C50X_USB
 232         tristate "Atmel at76c503/at76c505/at76c505a USB cards"
 233         depends on MAC80211 && WLAN_80211 && USB
 234         select FW_LOADER
 235         ---help---
 236           Enable support for USB Wireless devices using Atmel at76c503,
 237           at76c505 or at76c505a chips.
 238
 239 config AIRO_CS
 240         tristate "Cisco/Aironet 34X/35X/4500/4800 PCMCIA cards"
 241         depends on PCMCIA && (BROKEN || !M32R) && WLAN_80211
 242         select WIRELESS_EXT
 243         select CRYPTO
 244         select CRYPTO_AES
 245         ---help---
 246           This is the standard Linux driver to support Cisco/Aironet PCMCIA
 247           802.11 wireless cards.  This driver is the same as the Aironet
 248           driver part of the Linux Pcmcia package.
 249           It supports the new 802.11b cards from Cisco (Cisco 34X, Cisco 35X
 250           - with or without encryption) as well as card before the Cisco
 251           acquisition (Aironet 4500, Aironet 4800, Aironet 4800B). It also
 252           supports OEM of Cisco such as the DELL TrueMobile 4800 and Xircom
 253           802.11b cards.
 254
 255           This driver support both the standard Linux Wireless Extensions
 256           and Cisco proprietary API, so both the Linux Wireless Tools and the
 257           Cisco Linux utilities can be used to configure the card.
 258
 259 config PCMCIA_WL3501
 260       tristate "Planet WL3501 PCMCIA cards"
 261       depends on EXPERIMENTAL && PCMCIA && WLAN_80211
 262       select WIRELESS_EXT
 263        ---help---
 264          A driver for WL3501 PCMCIA 802.11 wireless cards made by Planet.
 265          It has basic support for Linux wireless extensions and initial
 266          micro support for ethtool.
 267
 268 config PRISM54
 269         tristate 'Intersil Prism GT/Duette/Indigo PCI/Cardbus'
 270         depends on PCI && EXPERIMENTAL && WLAN_80211
 271         select WIRELESS_EXT
 272         select FW_LOADER
 273         ---help---
 274           Enable PCI and Cardbus support for the following chipset based cards:
 275
 276           ISL3880 - Prism GT            802.11 b/g
 277           ISL3877 - Prism Indigo        802.11 a
 278           ISL3890 - Prism Duette        802.11 a/b/g
 279
 280           For a complete list of supported cards visit <http://prism54.org>.
 281           Here is the latest confirmed list of supported cards:
 282
 283           3com OfficeConnect 11g Cardbus Card aka 3CRWE154G72 (version 1)
 284           Allnet ALL0271 PCI Card
 285           Compex WL54G Cardbus Card
 286           Corega CG-WLCB54GT Cardbus Card
 287           D-Link Air Plus Xtreme G A1 Cardbus Card aka DWL-g650
 288           I-O Data WN-G54/CB Cardbus Card
 289           Kobishi XG-300 aka Z-Com Cardbus Card
 290           Netgear WG511 Cardbus Card
 291           Ovislink WL-5400PCI PCI Card
 292           Peabird WLG-PCI PCI Card
 293           Sitecom WL-100i Cardbus Card
 294           Sitecom WL-110i PCI Card
 295           SMC2802W -    EZ Connect g 2.4GHz 54 Mbps Wireless PCI Card
 296           SMC2835W -    EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Card
 297           SMC2835W-V2 - EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Card
 298           Z-Com XG-900 PCI Card
 299           Zyxel G-100 Cardbus Card
 300
 301           If you enable this you will need a firmware file as well.
 302           You will need to copy this to /usr/lib/hotplug/firmware/isl3890.
 303           You can get this non-GPL'd firmware file from the Prism54 project page:
 304           <http://prism54.org>
 305           You will also need the /etc/hotplug/firmware.agent script from
 306           a current hotplug package.
 307
 308           Note: You need a motherboard with DMA support to use any of these cards
 309
 310           If you want to compile the driver as a module ( = code which can be
 311           inserted in and removed from the running kernel whenever you want),
 312           say M here and read <file:Documentation/kbuild/modules.txt>.
 313           The module will be called prism54.
 314
 315 config USB_ZD1201
 316         tristate "USB ZD1201 based Wireless device support"
 317         depends on USB && WLAN_80211
 318         select WIRELESS_EXT
 319         select FW_LOADER
 320         ---help---
 321           Say Y if you want to use wireless LAN adapters based on the ZyDAS
 322           ZD1201 chip.
 323
 324           This driver makes the adapter appear as a normal Ethernet interface,
 325           typically on wlan0.
 326
 327           The zd1201 device requires external firmware to be loaded.
 328           This can be found at http://linux-lc100020.sourceforge.net/
 329
 330           To compile this driver as a module, choose M here: the
 331           module will be called zd1201.
 332
 333 config USB_NET_RNDIS_WLAN
 334         tristate "Wireless RNDIS USB support"
 335         depends on USB && WLAN_80211 && EXPERIMENTAL
 336         depends on CFG80211
 337         select USB_USBNET
 338         select USB_NET_CDCETHER
 339         select USB_NET_RNDIS_HOST
 340         select WIRELESS_EXT
 341         ---help---
 342           This is a driver for wireless RNDIS devices.
 343           These are USB based adapters found in devices such as:
 344
 345           Buffalo WLI-U2-KG125S
 346           U.S. Robotics USR5421
 347           Belkin F5D7051
 348           Linksys WUSB54GSv2
 349           Linksys WUSB54GSC
 350           Asus WL169gE
 351           Eminent EM4045
 352           BT Voyager 1055
 353           Linksys WUSB54GSv1
 354           U.S. Robotics USR5420
 355           BUFFALO WLI-USB-G54
 356
 357           All of these devices are based on Broadcom 4320 chip which is the
 358           only wireless RNDIS chip known to date.
 359
 360           If you choose to build a module, it'll be called rndis_wlan.
 361
 362 config RTL8180
 363         tristate "Realtek 8180/8185 PCI support"
 364         depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
 365         select EEPROM_93CX6
 366         ---help---
 367           This is a driver for RTL8180 and RTL8185 based cards.
 368           These are PCI based chips found in cards such as:
 369
 370           (RTL8185 802.11g)
 371           A-Link WL54PC
 372
 373           (RTL8180 802.11b)
 374           Belkin F5D6020 v3
 375           Belkin F5D6020 v3
 376           Dlink DWL-610
 377           Dlink DWL-510
 378           Netgear MA521
 379           Level-One WPC-0101
 380           Acer Aspire 1357 LMi
 381           VCTnet PC-11B1
 382           Ovislink AirLive WL-1120PCM
 383           Mentor WL-PCI
 384           Linksys WPC11 v4
 385           TrendNET TEW-288PI
 386           D-Link DWL-520 Rev D
 387           Repotec RP-WP7126
 388           TP-Link TL-WN250/251
 389           Zonet ZEW1000
 390           Longshine LCS-8031-R
 391           HomeLine HLW-PCC200
 392           GigaFast WF721-AEX
 393           Planet WL-3553
 394           Encore ENLWI-PCI1-NT
 395           TrendNET TEW-266PC
 396           Gigabyte GN-WLMR101
 397           Siemens-fujitsu Amilo D1840W
 398           Edimax EW-7126
 399           PheeNet WL-11PCIR
 400           Tonze PC-2100T
 401           Planet WL-8303
 402           Dlink DWL-650 v M1
 403           Edimax EW-7106
 404           Q-Tec 770WC
 405           Topcom Skyr@cer 4011b
 406           Roper FreeLan 802.11b (edition 2004)
 407           Wistron Neweb Corp CB-200B
 408           Pentagram HorNET
 409           QTec 775WC
 410           TwinMOS Booming B Series
 411           Micronet SP906BB
 412           Sweex LC700010
 413           Surecom EP-9428
 414           Safecom SWLCR-1100
 415
 416           Thanks to Realtek for their support!
 417
 418 config RTL8187
 419         tristate "Realtek 8187 and 8187B USB support"
 420         depends on MAC80211 && USB && WLAN_80211
 421         select EEPROM_93CX6
 422         ---help---
 423           This is a driver for RTL8187 and RTL8187B based cards.
 424           These are USB based chips found in devices such as:
 425
 426           Netgear WG111v2
 427           Level 1 WNC-0301USB
 428           Micronet SP907GK V5
 429           Encore ENUWI-G2
 430           Trendnet TEW-424UB
 431           ASUS P5B Deluxe
 432           Toshiba Satellite Pro series of laptops
 433           Asus Wireless Link
 434           Linksys WUSB54GC-EU
 435
 436           Thanks to Realtek for their support!
 437
 438 # If possible, automatically enable LEDs for RTL8187.
 439
 440 config RTL8187_LEDS
 441         bool
 442         depends on RTL8187 && MAC80211_LEDS && (LEDS_CLASS = y || LEDS_CLASS = RTL8187)
 443         default y
 444
 445 config ADM8211
 446         tristate "ADMtek ADM8211 support"
 447         depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
 448         select CRC32
 449         select EEPROM_93CX6
 450         ---help---
 451           This driver is for ADM8211A, ADM8211B, and ADM8211C based cards.
 452           These are PCI/mini-PCI/Cardbus 802.11b chips found in cards such as:
 453
 454           Xterasys Cardbus XN-2411b
 455           Blitz NetWave Point PC
 456           TrendNet 221pc
 457           Belkin F5D6001
 458           SMC 2635W
 459           Linksys WPC11 v1
 460           Fiberline FL-WL-200X
 461           3com Office Connect (3CRSHPW796)
 462           Corega WLPCIB-11
 463           SMC 2602W V2 EU
 464           D-Link DWL-520 Revision C
 465
 466           However, some of these cards have been replaced with other chips
 467           like the RTL8180L (Xterasys Cardbus XN-2411b, Belkin F5D6001) or
 468           the Ralink RT2400 (SMC2635W) without a model number change.
 469
 470           Thanks to Infineon-ADMtek for their support of this driver.
 471
 472 config MAC80211_HWSIM
 473         tristate "Simulated radio testing tool for mac80211"
 474         depends on MAC80211 && WLAN_80211
 475         ---help---
 476           This driver is a developer testing tool that can be used to test
 477           IEEE 802.11 networking stack (mac80211) functionality. This is not
 478           needed for normal wireless LAN usage and is only for testing. See
 479           Documentation/networking/mac80211_hwsim for more information on how
 480           to use this tool.
 481
 482           To compile this driver as a module, choose M here: the module will be
 483           called mac80211_hwsim.  If unsure, say N.
 484
 485 config MWL8K
 486         tristate "Marvell 88W8xxx PCI/PCIe Wireless support"
 487         depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL
 488         ---help---
 489           This driver supports Marvell TOPDOG 802.11 wireless cards.
 490
 491           To compile this driver as a module, choose M here: the module
 492           will be called mwl8k.  If unsure, say N.
 493
 494 source "drivers/net/wireless/p54/Kconfig"
 495 source "drivers/net/wireless/ath/Kconfig"
 496 source "drivers/net/wireless/ipw2x00/Kconfig"
 497 source "drivers/net/wireless/iwlwifi/Kconfig"
 498 source "drivers/net/wireless/hostap/Kconfig"
 499 source "drivers/net/wireless/b43/Kconfig"
 500 source "drivers/net/wireless/b43legacy/Kconfig"
 501 source "drivers/net/wireless/zd1211rw/Kconfig"
 502 source "drivers/net/wireless/rt2x00/Kconfig"
 503 source "drivers/net/wireless/orinoco/Kconfig"
 504 source "drivers/net/wireless/wl12xx/Kconfig"
 505 source "drivers/net/wireless/iwmc3200wifi/Kconfig"
 506
 507 endmenu