1 /******************************************************************************
3 * Copyright(c) 2003 - 2008 Intel Corporation. All rights reserved.
5 * This program is free software; you can redistribute it and/or modify it
6 * under the terms of version 2 of the GNU General Public License as
7 * published by the Free Software Foundation.
9 * This program is distributed in the hope that it will be useful, but WITHOUT
10 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
11 * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
14 * You should have received a copy of the GNU General Public License along with
15 * this program; if not, write to the Free Software Foundation, Inc.,
16 * 51 Franklin Street, Fifth Floor, Boston, MA 02110, USA
18 * The full GNU General Public License is included in this distribution in the
19 * file called LICENSE.
21 * Contact Information:
22 * James P. Ketrenos <ipw2100-admin@linux.intel.com>
23 * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
25 *****************************************************************************/
27 #include <linux/kernel.h>
28 #include <linux/module.h>
29 #include <linux/version.h>
30 #include <linux/init.h>
31 #include <linux/pci.h>
32 #include <linux/dma-mapping.h>
33 #include <linux/delay.h>
34 #include <linux/skbuff.h>
35 #include <linux/netdevice.h>
36 #include <linux/wireless.h>
37 #include <net/mac80211.h>
38 #include <linux/etherdevice.h>
39 #include <asm/unaligned.h>
41 #include "iwl-eeprom.h"
44 #include "iwl-helpers.h"
46 static void iwl4965_hw_card_show_info(struct iwl_priv
*priv
);
48 #define IWL_DECLARE_RATE_INFO(r, s, ip, in, rp, rn, pp, np) \
49 [IWL_RATE_##r##M_INDEX] = { IWL_RATE_##r##M_PLCP, \
50 IWL_RATE_SISO_##s##M_PLCP, \
51 IWL_RATE_MIMO_##s##M_PLCP, \
52 IWL_RATE_##r##M_IEEE, \
53 IWL_RATE_##ip##M_INDEX, \
54 IWL_RATE_##in##M_INDEX, \
55 IWL_RATE_##rp##M_INDEX, \
56 IWL_RATE_##rn##M_INDEX, \
57 IWL_RATE_##pp##M_INDEX, \
58 IWL_RATE_##np##M_INDEX }
62 * rate, ht rate, prev rate, next rate, prev tgg rate, next tgg rate
64 * If there isn't a valid next or previous rate then INV is used which
65 * maps to IWL_RATE_INVALID
68 const struct iwl4965_rate_info iwl4965_rates
[IWL_RATE_COUNT
] = {
69 IWL_DECLARE_RATE_INFO(1, INV
, INV
, 2, INV
, 2, INV
, 2), /* 1mbps */
70 IWL_DECLARE_RATE_INFO(2, INV
, 1, 5, 1, 5, 1, 5), /* 2mbps */
71 IWL_DECLARE_RATE_INFO(5, INV
, 2, 6, 2, 11, 2, 11), /*5.5mbps */
72 IWL_DECLARE_RATE_INFO(11, INV
, 9, 12, 9, 12, 5, 18), /* 11mbps */
73 IWL_DECLARE_RATE_INFO(6, 6, 5, 9, 5, 11, 5, 11), /* 6mbps */
74 IWL_DECLARE_RATE_INFO(9, 6, 6, 11, 6, 11, 5, 11), /* 9mbps */
75 IWL_DECLARE_RATE_INFO(12, 12, 11, 18, 11, 18, 11, 18), /* 12mbps */
76 IWL_DECLARE_RATE_INFO(18, 18, 12, 24, 12, 24, 11, 24), /* 18mbps */
77 IWL_DECLARE_RATE_INFO(24, 24, 18, 36, 18, 36, 18, 36), /* 24mbps */
78 IWL_DECLARE_RATE_INFO(36, 36, 24, 48, 24, 48, 24, 48), /* 36mbps */
79 IWL_DECLARE_RATE_INFO(48, 48, 36, 54, 36, 54, 36, 54), /* 48mbps */
80 IWL_DECLARE_RATE_INFO(54, 54, 48, INV
, 48, INV
, 48, INV
),/* 54mbps */
81 IWL_DECLARE_RATE_INFO(60, 60, 48, INV
, 48, INV
, 48, INV
),/* 60mbps */
84 #ifdef CONFIG_IWL4965_HT
86 static const u16 default_tid_to_tx_fifo
[] = {
106 #endif /*CONFIG_IWL4965_HT */
108 static int iwl4965_init_drv(struct iwl_priv
*priv
)
113 priv
->antenna
= (enum iwl4965_antenna
)iwl4965_mod_params
.antenna
;
114 priv
->retry_rate
= 1;
115 priv
->ibss_beacon
= NULL
;
117 spin_lock_init(&priv
->lock
);
118 spin_lock_init(&priv
->power_data
.lock
);
119 spin_lock_init(&priv
->sta_lock
);
120 spin_lock_init(&priv
->hcmd_lock
);
121 spin_lock_init(&priv
->lq_mngr
.lock
);
123 for (i
= 0; i
< IWL_IBSS_MAC_HASH_SIZE
; i
++)
124 INIT_LIST_HEAD(&priv
->ibss_mac_hash
[i
]);
126 INIT_LIST_HEAD(&priv
->free_frames
);
128 mutex_init(&priv
->mutex
);
130 /* Clear the driver's (not device's) station table */
131 iwlcore_clear_stations_table(priv
);
133 priv
->data_retry_limit
= -1;
134 priv
->ieee_channels
= NULL
;
135 priv
->ieee_rates
= NULL
;
136 priv
->band
= IEEE80211_BAND_2GHZ
;
138 priv
->iw_mode
= IEEE80211_IF_TYPE_STA
;
140 priv
->use_ant_b_for_management_frame
= 1; /* start with ant B */
141 priv
->valid_antenna
= 0x7; /* assume all 3 connected */
142 priv
->ps_mode
= IWL_MIMO_PS_NONE
;
144 /* Choose which receivers/antennas to use */
145 iwl4965_set_rxon_chain(priv
);
147 iwlcore_reset_qos(priv
);
149 priv
->qos_data
.qos_active
= 0;
150 priv
->qos_data
.qos_cap
.val
= 0;
152 iwlcore_set_rxon_channel(priv
, IEEE80211_BAND_2GHZ
, 6);
154 priv
->rates_mask
= IWL_RATES_MASK
;
155 /* If power management is turned on, default to AC mode */
156 priv
->power_mode
= IWL_POWER_AC
;
157 priv
->user_txpower_limit
= IWL_DEFAULT_TX_POWER
;
159 ret
= iwl_init_channel_map(priv
);
161 IWL_ERROR("initializing regulatory failed: %d\n", ret
);
165 ret
= iwl4965_init_geos(priv
);
167 IWL_ERROR("initializing geos failed: %d\n", ret
);
168 goto err_free_channel_map
;
171 iwl4965_rate_control_register(priv
->hw
);
172 ret
= ieee80211_register_hw(priv
->hw
);
174 IWL_ERROR("Failed to register network device (error %d)\n",
179 priv
->hw
->conf
.beacon_int
= 100;
180 priv
->mac80211_registered
= 1;
185 iwl4965_free_geos(priv
);
186 err_free_channel_map
:
187 iwl_free_channel_map(priv
);
192 static int is_fat_channel(__le32 rxon_flags
)
194 return (rxon_flags
& RXON_FLG_CHANNEL_MODE_PURE_40_MSK
) ||
195 (rxon_flags
& RXON_FLG_CHANNEL_MODE_MIXED_MSK
);
198 static u8
is_single_stream(struct iwl_priv
*priv
)
200 #ifdef CONFIG_IWL4965_HT
201 if (!priv
->current_ht_config
.is_ht
||
202 (priv
->current_ht_config
.supp_mcs_set
[1] == 0) ||
203 (priv
->ps_mode
== IWL_MIMO_PS_STATIC
))
207 #endif /*CONFIG_IWL4965_HT */
211 int iwl4965_hwrate_to_plcp_idx(u32 rate_n_flags
)
215 /* 4965 HT rate format */
216 if (rate_n_flags
& RATE_MCS_HT_MSK
) {
217 idx
= (rate_n_flags
& 0xff);
219 if (idx
>= IWL_RATE_MIMO_6M_PLCP
)
220 idx
= idx
- IWL_RATE_MIMO_6M_PLCP
;
222 idx
+= IWL_FIRST_OFDM_RATE
;
223 /* skip 9M not supported in ht*/
224 if (idx
>= IWL_RATE_9M_INDEX
)
226 if ((idx
>= IWL_FIRST_OFDM_RATE
) && (idx
<= IWL_LAST_OFDM_RATE
))
229 /* 4965 legacy rate format, search for match in table */
231 for (idx
= 0; idx
< ARRAY_SIZE(iwl4965_rates
); idx
++)
232 if (iwl4965_rates
[idx
].plcp
== (rate_n_flags
& 0xFF))
240 * translate ucode response to mac80211 tx status control values
242 void iwl4965_hwrate_to_tx_control(struct iwl_priv
*priv
, u32 rate_n_flags
,
243 struct ieee80211_tx_control
*control
)
247 control
->antenna_sel_tx
=
248 ((rate_n_flags
& RATE_MCS_ANT_AB_MSK
) >> RATE_MCS_ANT_A_POS
);
249 if (rate_n_flags
& RATE_MCS_HT_MSK
)
250 control
->flags
|= IEEE80211_TXCTL_OFDM_HT
;
251 if (rate_n_flags
& RATE_MCS_GF_MSK
)
252 control
->flags
|= IEEE80211_TXCTL_GREEN_FIELD
;
253 if (rate_n_flags
& RATE_MCS_FAT_MSK
)
254 control
->flags
|= IEEE80211_TXCTL_40_MHZ_WIDTH
;
255 if (rate_n_flags
& RATE_MCS_DUP_MSK
)
256 control
->flags
|= IEEE80211_TXCTL_DUP_DATA
;
257 if (rate_n_flags
& RATE_MCS_SGI_MSK
)
258 control
->flags
|= IEEE80211_TXCTL_SHORT_GI
;
259 /* since iwl4965_hwrate_to_plcp_idx is band indifferent, we always use
260 * IEEE80211_BAND_2GHZ band as it contains all the rates */
261 rate_index
= iwl4965_hwrate_to_plcp_idx(rate_n_flags
);
262 if (rate_index
== -1)
263 control
->tx_rate
= NULL
;
266 &priv
->bands
[IEEE80211_BAND_2GHZ
].bitrates
[rate_index
];
270 * Determine how many receiver/antenna chains to use.
271 * More provides better reception via diversity. Fewer saves power.
272 * MIMO (dual stream) requires at least 2, but works better with 3.
273 * This does not determine *which* chains to use, just how many.
275 static int iwl4965_get_rx_chain_counter(struct iwl_priv
*priv
,
276 u8
*idle_state
, u8
*rx_state
)
278 u8 is_single
= is_single_stream(priv
);
279 u8 is_cam
= test_bit(STATUS_POWER_PMI
, &priv
->status
) ? 0 : 1;
281 /* # of Rx chains to use when expecting MIMO. */
282 if (is_single
|| (!is_cam
&& (priv
->ps_mode
== IWL_MIMO_PS_STATIC
)))
287 /* # Rx chains when idling and maybe trying to save power */
288 switch (priv
->ps_mode
) {
289 case IWL_MIMO_PS_STATIC
:
290 case IWL_MIMO_PS_DYNAMIC
:
291 *idle_state
= (is_cam
) ? 2 : 1;
293 case IWL_MIMO_PS_NONE
:
294 *idle_state
= (is_cam
) ? *rx_state
: 1;
304 int iwl4965_hw_rxq_stop(struct iwl_priv
*priv
)
309 spin_lock_irqsave(&priv
->lock
, flags
);
310 rc
= iwl4965_grab_nic_access(priv
);
312 spin_unlock_irqrestore(&priv
->lock
, flags
);
317 iwl4965_write_direct32(priv
, FH_MEM_RCSR_CHNL0_CONFIG_REG
, 0);
318 rc
= iwl4965_poll_direct_bit(priv
, FH_MEM_RSSR_RX_STATUS_REG
,
321 IWL_ERROR("Can't stop Rx DMA.\n");
323 iwl4965_release_nic_access(priv
);
324 spin_unlock_irqrestore(&priv
->lock
, flags
);
329 u8
iwl4965_hw_find_station(struct iwl_priv
*priv
, const u8
*addr
)
333 int ret
= IWL_INVALID_STATION
;
335 DECLARE_MAC_BUF(mac
);
337 if ((priv
->iw_mode
== IEEE80211_IF_TYPE_IBSS
) ||
338 (priv
->iw_mode
== IEEE80211_IF_TYPE_AP
))
341 if (is_broadcast_ether_addr(addr
))
342 return priv
->hw_setting
.bcast_sta_id
;
344 spin_lock_irqsave(&priv
->sta_lock
, flags
);
345 for (i
= start
; i
< priv
->hw_setting
.max_stations
; i
++)
346 if ((priv
->stations
[i
].used
) &&
348 (priv
->stations
[i
].sta
.sta
.addr
, addr
))) {
353 IWL_DEBUG_ASSOC_LIMIT("can not find STA %s total %d\n",
354 print_mac(mac
, addr
), priv
->num_stations
);
357 spin_unlock_irqrestore(&priv
->sta_lock
, flags
);
361 static int iwl4965_nic_set_pwr_src(struct iwl_priv
*priv
, int pwr_max
)
366 spin_lock_irqsave(&priv
->lock
, flags
);
367 ret
= iwl4965_grab_nic_access(priv
);
369 spin_unlock_irqrestore(&priv
->lock
, flags
);
376 ret
= pci_read_config_dword(priv
->pci_dev
, PCI_POWER_SOURCE
,
379 if (val
& PCI_CFG_PMC_PME_FROM_D3COLD_SUPPORT
)
380 iwl4965_set_bits_mask_prph(priv
, APMG_PS_CTRL_REG
,
381 APMG_PS_CTRL_VAL_PWR_SRC_VAUX
,
382 ~APMG_PS_CTRL_MSK_PWR_SRC
);
384 iwl4965_set_bits_mask_prph(priv
, APMG_PS_CTRL_REG
,
385 APMG_PS_CTRL_VAL_PWR_SRC_VMAIN
,
386 ~APMG_PS_CTRL_MSK_PWR_SRC
);
388 iwl4965_release_nic_access(priv
);
389 spin_unlock_irqrestore(&priv
->lock
, flags
);
394 static int iwl4965_rx_init(struct iwl_priv
*priv
, struct iwl4965_rx_queue
*rxq
)
398 unsigned int rb_size
;
400 spin_lock_irqsave(&priv
->lock
, flags
);
401 rc
= iwl4965_grab_nic_access(priv
);
403 spin_unlock_irqrestore(&priv
->lock
, flags
);
407 if (iwl4965_mod_params
.amsdu_size_8K
)
408 rb_size
= FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_8K
;
410 rb_size
= FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_4K
;
413 iwl4965_write_direct32(priv
, FH_MEM_RCSR_CHNL0_CONFIG_REG
, 0);
415 /* Reset driver's Rx queue write index */
416 iwl4965_write_direct32(priv
, FH_RSCSR_CHNL0_RBDCB_WPTR_REG
, 0);
418 /* Tell device where to find RBD circular buffer in DRAM */
419 iwl4965_write_direct32(priv
, FH_RSCSR_CHNL0_RBDCB_BASE_REG
,
422 /* Tell device where in DRAM to update its Rx status */
423 iwl4965_write_direct32(priv
, FH_RSCSR_CHNL0_STTS_WPTR_REG
,
424 (priv
->hw_setting
.shared_phys
+
425 offsetof(struct iwl4965_shared
, val0
)) >> 4);
427 /* Enable Rx DMA, enable host interrupt, Rx buffer size 4k, 256 RBDs */
428 iwl4965_write_direct32(priv
, FH_MEM_RCSR_CHNL0_CONFIG_REG
,
429 FH_RCSR_RX_CONFIG_CHNL_EN_ENABLE_VAL
|
430 FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_INT_HOST_VAL
|
433 (RX_QUEUE_SIZE_LOG
<<
434 FH_RCSR_RX_CONFIG_RBDCB_SIZE_BITSHIFT
));
437 * iwl4965_write32(priv,CSR_INT_COAL_REG,0);
440 iwl4965_release_nic_access(priv
);
441 spin_unlock_irqrestore(&priv
->lock
, flags
);
446 /* Tell 4965 where to find the "keep warm" buffer */
447 static int iwl4965_kw_init(struct iwl_priv
*priv
)
452 spin_lock_irqsave(&priv
->lock
, flags
);
453 rc
= iwl4965_grab_nic_access(priv
);
457 iwl4965_write_direct32(priv
, IWL_FH_KW_MEM_ADDR_REG
,
458 priv
->kw
.dma_addr
>> 4);
459 iwl4965_release_nic_access(priv
);
461 spin_unlock_irqrestore(&priv
->lock
, flags
);
465 static int iwl4965_kw_alloc(struct iwl_priv
*priv
)
467 struct pci_dev
*dev
= priv
->pci_dev
;
468 struct iwl4965_kw
*kw
= &priv
->kw
;
470 kw
->size
= IWL4965_KW_SIZE
; /* TBW need set somewhere else */
471 kw
->v_addr
= pci_alloc_consistent(dev
, kw
->size
, &kw
->dma_addr
);
479 * iwl4965_kw_free - Free the "keep warm" buffer
481 static void iwl4965_kw_free(struct iwl_priv
*priv
)
483 struct pci_dev
*dev
= priv
->pci_dev
;
484 struct iwl4965_kw
*kw
= &priv
->kw
;
487 pci_free_consistent(dev
, kw
->size
, kw
->v_addr
, kw
->dma_addr
);
488 memset(kw
, 0, sizeof(*kw
));
493 * iwl4965_txq_ctx_reset - Reset TX queue context
494 * Destroys all DMA structures and initialise them again
499 static int iwl4965_txq_ctx_reset(struct iwl_priv
*priv
)
502 int txq_id
, slots_num
;
505 iwl4965_kw_free(priv
);
507 /* Free all tx/cmd queues and keep-warm buffer */
508 iwl4965_hw_txq_ctx_free(priv
);
510 /* Alloc keep-warm buffer */
511 rc
= iwl4965_kw_alloc(priv
);
513 IWL_ERROR("Keep Warm allocation failed");
517 spin_lock_irqsave(&priv
->lock
, flags
);
519 rc
= iwl4965_grab_nic_access(priv
);
521 IWL_ERROR("TX reset failed");
522 spin_unlock_irqrestore(&priv
->lock
, flags
);
526 /* Turn off all Tx DMA channels */
527 iwl4965_write_prph(priv
, KDR_SCD_TXFACT
, 0);
528 iwl4965_release_nic_access(priv
);
529 spin_unlock_irqrestore(&priv
->lock
, flags
);
531 /* Tell 4965 where to find the keep-warm buffer */
532 rc
= iwl4965_kw_init(priv
);
534 IWL_ERROR("kw_init failed\n");
538 /* Alloc and init all (default 16) Tx queues,
539 * including the command queue (#4) */
540 for (txq_id
= 0; txq_id
< priv
->hw_setting
.max_txq_num
; txq_id
++) {
541 slots_num
= (txq_id
== IWL_CMD_QUEUE_NUM
) ?
542 TFD_CMD_SLOTS
: TFD_TX_CMD_SLOTS
;
543 rc
= iwl4965_tx_queue_init(priv
, &priv
->txq
[txq_id
], slots_num
,
546 IWL_ERROR("Tx %d queue init failed\n", txq_id
);
554 iwl4965_hw_txq_ctx_free(priv
);
556 iwl4965_kw_free(priv
);
561 int iwl4965_hw_nic_init(struct iwl_priv
*priv
)
565 struct iwl4965_rx_queue
*rxq
= &priv
->rxq
;
570 iwl4965_power_init_handle(priv
);
573 spin_lock_irqsave(&priv
->lock
, flags
);
575 iwl4965_set_bit(priv
, CSR_GIO_CHICKEN_BITS
,
576 CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER
);
578 iwl4965_set_bit(priv
, CSR_GP_CNTRL
, CSR_GP_CNTRL_REG_FLAG_INIT_DONE
);
579 rc
= iwl4965_poll_bit(priv
, CSR_GP_CNTRL
,
580 CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY
,
581 CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY
, 25000);
583 spin_unlock_irqrestore(&priv
->lock
, flags
);
584 IWL_DEBUG_INFO("Failed to init the card\n");
588 rc
= iwl4965_grab_nic_access(priv
);
590 spin_unlock_irqrestore(&priv
->lock
, flags
);
594 iwl4965_read_prph(priv
, APMG_CLK_CTRL_REG
);
596 iwl4965_write_prph(priv
, APMG_CLK_CTRL_REG
,
597 APMG_CLK_VAL_DMA_CLK_RQT
|
598 APMG_CLK_VAL_BSM_CLK_RQT
);
599 iwl4965_read_prph(priv
, APMG_CLK_CTRL_REG
);
603 iwl4965_set_bits_prph(priv
, APMG_PCIDEV_STT_REG
,
604 APMG_PCIDEV_STT_VAL_L1_ACT_DIS
);
606 iwl4965_release_nic_access(priv
);
607 iwl4965_write32(priv
, CSR_INT_COALESCING
, 512 / 32);
608 spin_unlock_irqrestore(&priv
->lock
, flags
);
610 /* Determine HW type */
611 rc
= pci_read_config_byte(priv
->pci_dev
, PCI_REVISION_ID
, &rev_id
);
615 IWL_DEBUG_INFO("HW Revision ID = 0x%X\n", rev_id
);
617 iwl4965_nic_set_pwr_src(priv
, 1);
618 spin_lock_irqsave(&priv
->lock
, flags
);
620 if ((rev_id
& 0x80) == 0x80 && (rev_id
& 0x7f) < 8) {
621 pci_read_config_dword(priv
->pci_dev
, PCI_REG_WUM8
, &val
);
622 /* Enable No Snoop field */
623 pci_write_config_dword(priv
->pci_dev
, PCI_REG_WUM8
,
627 spin_unlock_irqrestore(&priv
->lock
, flags
);
629 if (priv
->eeprom
.calib_version
< EEPROM_TX_POWER_VERSION_NEW
) {
630 IWL_ERROR("Older EEPROM detected! Aborting.\n");
634 pci_read_config_byte(priv
->pci_dev
, PCI_LINK_CTRL
, &val_link
);
636 /* disable L1 entry -- workaround for pre-B1 */
637 pci_write_config_byte(priv
->pci_dev
, PCI_LINK_CTRL
, val_link
& ~0x02);
639 spin_lock_irqsave(&priv
->lock
, flags
);
641 /* set CSR_HW_CONFIG_REG for uCode use */
643 iwl4965_set_bit(priv
, CSR_HW_IF_CONFIG_REG
,
644 CSR49_HW_IF_CONFIG_REG_BIT_4965_R
|
645 CSR49_HW_IF_CONFIG_REG_BIT_RADIO_SI
|
646 CSR49_HW_IF_CONFIG_REG_BIT_MAC_SI
);
648 rc
= iwl4965_grab_nic_access(priv
);
650 spin_unlock_irqrestore(&priv
->lock
, flags
);
651 IWL_DEBUG_INFO("Failed to init the card\n");
655 iwl4965_read_prph(priv
, APMG_PS_CTRL_REG
);
656 iwl4965_set_bits_prph(priv
, APMG_PS_CTRL_REG
,
657 APMG_PS_CTRL_VAL_RESET_REQ
);
659 iwl4965_clear_bits_prph(priv
, APMG_PS_CTRL_REG
,
660 APMG_PS_CTRL_VAL_RESET_REQ
);
662 iwl4965_release_nic_access(priv
);
663 spin_unlock_irqrestore(&priv
->lock
, flags
);
665 iwl4965_hw_card_show_info(priv
);
669 /* Allocate the RX queue, or reset if it is already allocated */
671 rc
= iwl4965_rx_queue_alloc(priv
);
673 IWL_ERROR("Unable to initialize Rx queue\n");
677 iwl4965_rx_queue_reset(priv
, rxq
);
679 iwl4965_rx_replenish(priv
);
681 iwl4965_rx_init(priv
, rxq
);
683 spin_lock_irqsave(&priv
->lock
, flags
);
685 rxq
->need_update
= 1;
686 iwl4965_rx_queue_update_write_ptr(priv
, rxq
);
688 spin_unlock_irqrestore(&priv
->lock
, flags
);
690 /* Allocate and init all Tx and Command queues */
691 rc
= iwl4965_txq_ctx_reset(priv
);
695 if (priv
->eeprom
.sku_cap
& EEPROM_SKU_CAP_SW_RF_KILL_ENABLE
)
696 IWL_DEBUG_RF_KILL("SW RF KILL supported in EEPROM.\n");
698 if (priv
->eeprom
.sku_cap
& EEPROM_SKU_CAP_HW_RF_KILL_ENABLE
)
699 IWL_DEBUG_RF_KILL("HW RF KILL supported in EEPROM.\n");
701 set_bit(STATUS_INIT
, &priv
->status
);
706 int iwl4965_hw_nic_stop_master(struct iwl_priv
*priv
)
712 spin_lock_irqsave(&priv
->lock
, flags
);
714 /* set stop master bit */
715 iwl4965_set_bit(priv
, CSR_RESET
, CSR_RESET_REG_FLAG_STOP_MASTER
);
717 reg_val
= iwl4965_read32(priv
, CSR_GP_CNTRL
);
719 if (CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE
==
720 (reg_val
& CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE
))
721 IWL_DEBUG_INFO("Card in power save, master is already "
724 rc
= iwl4965_poll_bit(priv
, CSR_RESET
,
725 CSR_RESET_REG_FLAG_MASTER_DISABLED
,
726 CSR_RESET_REG_FLAG_MASTER_DISABLED
, 100);
728 spin_unlock_irqrestore(&priv
->lock
, flags
);
733 spin_unlock_irqrestore(&priv
->lock
, flags
);
734 IWL_DEBUG_INFO("stop master\n");
740 * iwl4965_hw_txq_ctx_stop - Stop all Tx DMA channels, free Tx queue memory
742 void iwl4965_hw_txq_ctx_stop(struct iwl_priv
*priv
)
748 /* Stop each Tx DMA channel, and wait for it to be idle */
749 for (txq_id
= 0; txq_id
< priv
->hw_setting
.max_txq_num
; txq_id
++) {
750 spin_lock_irqsave(&priv
->lock
, flags
);
751 if (iwl4965_grab_nic_access(priv
)) {
752 spin_unlock_irqrestore(&priv
->lock
, flags
);
756 iwl4965_write_direct32(priv
,
757 IWL_FH_TCSR_CHNL_TX_CONFIG_REG(txq_id
),
759 iwl4965_poll_direct_bit(priv
, IWL_FH_TSSR_TX_STATUS_REG
,
760 IWL_FH_TSSR_TX_STATUS_REG_MSK_CHNL_IDLE
762 iwl4965_release_nic_access(priv
);
763 spin_unlock_irqrestore(&priv
->lock
, flags
);
766 /* Deallocate memory for all Tx queues */
767 iwl4965_hw_txq_ctx_free(priv
);
770 int iwl4965_hw_nic_reset(struct iwl_priv
*priv
)
775 iwl4965_hw_nic_stop_master(priv
);
777 spin_lock_irqsave(&priv
->lock
, flags
);
779 iwl4965_set_bit(priv
, CSR_RESET
, CSR_RESET_REG_FLAG_SW_RESET
);
783 iwl4965_set_bit(priv
, CSR_GP_CNTRL
, CSR_GP_CNTRL_REG_FLAG_INIT_DONE
);
784 rc
= iwl4965_poll_bit(priv
, CSR_RESET
,
785 CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY
,
786 CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY
, 25);
790 rc
= iwl4965_grab_nic_access(priv
);
792 iwl4965_write_prph(priv
, APMG_CLK_EN_REG
,
793 APMG_CLK_VAL_DMA_CLK_RQT
|
794 APMG_CLK_VAL_BSM_CLK_RQT
);
798 iwl4965_set_bits_prph(priv
, APMG_PCIDEV_STT_REG
,
799 APMG_PCIDEV_STT_VAL_L1_ACT_DIS
);
801 iwl4965_release_nic_access(priv
);
804 clear_bit(STATUS_HCMD_ACTIVE
, &priv
->status
);
805 wake_up_interruptible(&priv
->wait_command_queue
);
807 spin_unlock_irqrestore(&priv
->lock
, flags
);
813 #define REG_RECALIB_PERIOD (60)
816 * iwl4965_bg_statistics_periodic - Timer callback to queue statistics
818 * This callback is provided in order to queue the statistics_work
819 * in work_queue context (v. softirq)
821 * This timer function is continually reset to execute within
822 * REG_RECALIB_PERIOD seconds since the last STATISTICS_NOTIFICATION
823 * was received. We need to ensure we receive the statistics in order
824 * to update the temperature used for calibrating the TXPOWER. However,
825 * we can't send the statistics command from softirq context (which
826 * is the context which timers run at) so we have to queue off the
827 * statistics_work to actually send the command to the hardware.
829 static void iwl4965_bg_statistics_periodic(unsigned long data
)
831 struct iwl_priv
*priv
= (struct iwl_priv
*)data
;
833 queue_work(priv
->workqueue
, &priv
->statistics_work
);
837 * iwl4965_bg_statistics_work - Send the statistics request to the hardware.
839 * This is queued by iwl4965_bg_statistics_periodic.
841 static void iwl4965_bg_statistics_work(struct work_struct
*work
)
843 struct iwl_priv
*priv
= container_of(work
, struct iwl_priv
,
846 if (test_bit(STATUS_EXIT_PENDING
, &priv
->status
))
849 mutex_lock(&priv
->mutex
);
850 iwl4965_send_statistics_request(priv
);
851 mutex_unlock(&priv
->mutex
);
854 #define CT_LIMIT_CONST 259
855 #define TM_CT_KILL_THRESHOLD 110
857 void iwl4965_rf_kill_ct_config(struct iwl_priv
*priv
)
859 struct iwl4965_ct_kill_config cmd
;
862 u32 crit_temperature
;
866 spin_lock_irqsave(&priv
->lock
, flags
);
867 iwl4965_write32(priv
, CSR_UCODE_DRV_GP1_CLR
,
868 CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT
);
869 spin_unlock_irqrestore(&priv
->lock
, flags
);
871 if (priv
->statistics
.flag
& STATISTICS_REPLY_FLG_FAT_MODE_MSK
) {
872 R1
= (s32
)le32_to_cpu(priv
->card_alive_init
.therm_r1
[1]);
873 R2
= (s32
)le32_to_cpu(priv
->card_alive_init
.therm_r2
[1]);
874 R3
= (s32
)le32_to_cpu(priv
->card_alive_init
.therm_r3
[1]);
876 R1
= (s32
)le32_to_cpu(priv
->card_alive_init
.therm_r1
[0]);
877 R2
= (s32
)le32_to_cpu(priv
->card_alive_init
.therm_r2
[0]);
878 R3
= (s32
)le32_to_cpu(priv
->card_alive_init
.therm_r3
[0]);
881 temp_th
= CELSIUS_TO_KELVIN(TM_CT_KILL_THRESHOLD
);
883 crit_temperature
= ((temp_th
* (R3
-R1
))/CT_LIMIT_CONST
) + R2
;
884 cmd
.critical_temperature_R
= cpu_to_le32(crit_temperature
);
885 rc
= iwl4965_send_cmd_pdu(priv
,
886 REPLY_CT_KILL_CONFIG_CMD
, sizeof(cmd
), &cmd
);
888 IWL_ERROR("REPLY_CT_KILL_CONFIG_CMD failed\n");
890 IWL_DEBUG_INFO("REPLY_CT_KILL_CONFIG_CMD succeeded\n");
893 #ifdef CONFIG_IWL4965_SENSITIVITY
895 /* "false alarms" are signals that our DSP tries to lock onto,
896 * but then determines that they are either noise, or transmissions
897 * from a distant wireless network (also "noise", really) that get
898 * "stepped on" by stronger transmissions within our own network.
899 * This algorithm attempts to set a sensitivity level that is high
900 * enough to receive all of our own network traffic, but not so
901 * high that our DSP gets too busy trying to lock onto non-network
903 static int iwl4965_sens_energy_cck(struct iwl_priv
*priv
,
906 struct statistics_general_data
*rx_info
)
910 u8 max_silence_rssi
= 0;
912 u8 silence_rssi_a
= 0;
913 u8 silence_rssi_b
= 0;
914 u8 silence_rssi_c
= 0;
917 /* "false_alarms" values below are cross-multiplications to assess the
918 * numbers of false alarms within the measured period of actual Rx
919 * (Rx is off when we're txing), vs the min/max expected false alarms
920 * (some should be expected if rx is sensitive enough) in a
921 * hypothetical listening period of 200 time units (TU), 204.8 msec:
923 * MIN_FA/fixed-time < false_alarms/actual-rx-time < MAX_FA/beacon-time
926 u32 false_alarms
= norm_fa
* 200 * 1024;
927 u32 max_false_alarms
= MAX_FA_CCK
* rx_enable_time
;
928 u32 min_false_alarms
= MIN_FA_CCK
* rx_enable_time
;
929 struct iwl4965_sensitivity_data
*data
= NULL
;
931 data
= &(priv
->sensitivity_data
);
933 data
->nrg_auto_corr_silence_diff
= 0;
935 /* Find max silence rssi among all 3 receivers.
936 * This is background noise, which may include transmissions from other
937 * networks, measured during silence before our network's beacon */
938 silence_rssi_a
= (u8
)((rx_info
->beacon_silence_rssi_a
&
939 ALL_BAND_FILTER
) >> 8);
940 silence_rssi_b
= (u8
)((rx_info
->beacon_silence_rssi_b
&
941 ALL_BAND_FILTER
) >> 8);
942 silence_rssi_c
= (u8
)((rx_info
->beacon_silence_rssi_c
&
943 ALL_BAND_FILTER
) >> 8);
945 val
= max(silence_rssi_b
, silence_rssi_c
);
946 max_silence_rssi
= max(silence_rssi_a
, (u8
) val
);
948 /* Store silence rssi in 20-beacon history table */
949 data
->nrg_silence_rssi
[data
->nrg_silence_idx
] = max_silence_rssi
;
950 data
->nrg_silence_idx
++;
951 if (data
->nrg_silence_idx
>= NRG_NUM_PREV_STAT_L
)
952 data
->nrg_silence_idx
= 0;
954 /* Find max silence rssi across 20 beacon history */
955 for (i
= 0; i
< NRG_NUM_PREV_STAT_L
; i
++) {
956 val
= data
->nrg_silence_rssi
[i
];
957 silence_ref
= max(silence_ref
, val
);
959 IWL_DEBUG_CALIB("silence a %u, b %u, c %u, 20-bcn max %u\n",
960 silence_rssi_a
, silence_rssi_b
, silence_rssi_c
,
963 /* Find max rx energy (min value!) among all 3 receivers,
964 * measured during beacon frame.
965 * Save it in 10-beacon history table. */
966 i
= data
->nrg_energy_idx
;
967 val
= min(rx_info
->beacon_energy_b
, rx_info
->beacon_energy_c
);
968 data
->nrg_value
[i
] = min(rx_info
->beacon_energy_a
, val
);
970 data
->nrg_energy_idx
++;
971 if (data
->nrg_energy_idx
>= 10)
972 data
->nrg_energy_idx
= 0;
974 /* Find min rx energy (max value) across 10 beacon history.
975 * This is the minimum signal level that we want to receive well.
976 * Add backoff (margin so we don't miss slightly lower energy frames).
977 * This establishes an upper bound (min value) for energy threshold. */
978 max_nrg_cck
= data
->nrg_value
[0];
979 for (i
= 1; i
< 10; i
++)
980 max_nrg_cck
= (u32
) max(max_nrg_cck
, (data
->nrg_value
[i
]));
983 IWL_DEBUG_CALIB("rx energy a %u, b %u, c %u, 10-bcn max/min %u\n",
984 rx_info
->beacon_energy_a
, rx_info
->beacon_energy_b
,
985 rx_info
->beacon_energy_c
, max_nrg_cck
- 6);
987 /* Count number of consecutive beacons with fewer-than-desired
989 if (false_alarms
< min_false_alarms
)
990 data
->num_in_cck_no_fa
++;
992 data
->num_in_cck_no_fa
= 0;
993 IWL_DEBUG_CALIB("consecutive bcns with few false alarms = %u\n",
994 data
->num_in_cck_no_fa
);
996 /* If we got too many false alarms this time, reduce sensitivity */
997 if (false_alarms
> max_false_alarms
) {
998 IWL_DEBUG_CALIB("norm FA %u > max FA %u\n",
999 false_alarms
, max_false_alarms
);
1000 IWL_DEBUG_CALIB("... reducing sensitivity\n");
1001 data
->nrg_curr_state
= IWL_FA_TOO_MANY
;
1003 if (data
->auto_corr_cck
> AUTO_CORR_MAX_TH_CCK
) {
1004 /* Store for "fewer than desired" on later beacon */
1005 data
->nrg_silence_ref
= silence_ref
;
1007 /* increase energy threshold (reduce nrg value)
1008 * to decrease sensitivity */
1009 if (data
->nrg_th_cck
> (NRG_MAX_CCK
+ NRG_STEP_CCK
))
1010 data
->nrg_th_cck
= data
->nrg_th_cck
1014 /* increase auto_corr values to decrease sensitivity */
1015 if (data
->auto_corr_cck
< AUTO_CORR_MAX_TH_CCK
)
1016 data
->auto_corr_cck
= AUTO_CORR_MAX_TH_CCK
+ 1;
1018 val
= data
->auto_corr_cck
+ AUTO_CORR_STEP_CCK
;
1019 data
->auto_corr_cck
= min((u32
)AUTO_CORR_MAX_CCK
, val
);
1021 val
= data
->auto_corr_cck_mrc
+ AUTO_CORR_STEP_CCK
;
1022 data
->auto_corr_cck_mrc
= min((u32
)AUTO_CORR_MAX_CCK_MRC
, val
);
1024 /* Else if we got fewer than desired, increase sensitivity */
1025 } else if (false_alarms
< min_false_alarms
) {
1026 data
->nrg_curr_state
= IWL_FA_TOO_FEW
;
1028 /* Compare silence level with silence level for most recent
1029 * healthy number or too many false alarms */
1030 data
->nrg_auto_corr_silence_diff
= (s32
)data
->nrg_silence_ref
-
1033 IWL_DEBUG_CALIB("norm FA %u < min FA %u, silence diff %d\n",
1034 false_alarms
, min_false_alarms
,
1035 data
->nrg_auto_corr_silence_diff
);
1037 /* Increase value to increase sensitivity, but only if:
1038 * 1a) previous beacon did *not* have *too many* false alarms
1039 * 1b) AND there's a significant difference in Rx levels
1040 * from a previous beacon with too many, or healthy # FAs
1041 * OR 2) We've seen a lot of beacons (100) with too few
1043 if ((data
->nrg_prev_state
!= IWL_FA_TOO_MANY
) &&
1044 ((data
->nrg_auto_corr_silence_diff
> NRG_DIFF
) ||
1045 (data
->num_in_cck_no_fa
> MAX_NUMBER_CCK_NO_FA
))) {
1047 IWL_DEBUG_CALIB("... increasing sensitivity\n");
1048 /* Increase nrg value to increase sensitivity */
1049 val
= data
->nrg_th_cck
+ NRG_STEP_CCK
;
1050 data
->nrg_th_cck
= min((u32
)NRG_MIN_CCK
, val
);
1052 /* Decrease auto_corr values to increase sensitivity */
1053 val
= data
->auto_corr_cck
- AUTO_CORR_STEP_CCK
;
1054 data
->auto_corr_cck
= max((u32
)AUTO_CORR_MIN_CCK
, val
);
1056 val
= data
->auto_corr_cck_mrc
- AUTO_CORR_STEP_CCK
;
1057 data
->auto_corr_cck_mrc
=
1058 max((u32
)AUTO_CORR_MIN_CCK_MRC
, val
);
1061 IWL_DEBUG_CALIB("... but not changing sensitivity\n");
1063 /* Else we got a healthy number of false alarms, keep status quo */
1065 IWL_DEBUG_CALIB(" FA in safe zone\n");
1066 data
->nrg_curr_state
= IWL_FA_GOOD_RANGE
;
1068 /* Store for use in "fewer than desired" with later beacon */
1069 data
->nrg_silence_ref
= silence_ref
;
1071 /* If previous beacon had too many false alarms,
1072 * give it some extra margin by reducing sensitivity again
1073 * (but don't go below measured energy of desired Rx) */
1074 if (IWL_FA_TOO_MANY
== data
->nrg_prev_state
) {
1075 IWL_DEBUG_CALIB("... increasing margin\n");
1076 data
->nrg_th_cck
-= NRG_MARGIN
;
1080 /* Make sure the energy threshold does not go above the measured
1081 * energy of the desired Rx signals (reduced by backoff margin),
1082 * or else we might start missing Rx frames.
1083 * Lower value is higher energy, so we use max()!
1085 data
->nrg_th_cck
= max(max_nrg_cck
, data
->nrg_th_cck
);
1086 IWL_DEBUG_CALIB("new nrg_th_cck %u\n", data
->nrg_th_cck
);
1088 data
->nrg_prev_state
= data
->nrg_curr_state
;
1094 static int iwl4965_sens_auto_corr_ofdm(struct iwl_priv
*priv
,
1099 u32 false_alarms
= norm_fa
* 200 * 1024;
1100 u32 max_false_alarms
= MAX_FA_OFDM
* rx_enable_time
;
1101 u32 min_false_alarms
= MIN_FA_OFDM
* rx_enable_time
;
1102 struct iwl4965_sensitivity_data
*data
= NULL
;
1104 data
= &(priv
->sensitivity_data
);
1106 /* If we got too many false alarms this time, reduce sensitivity */
1107 if (false_alarms
> max_false_alarms
) {
1109 IWL_DEBUG_CALIB("norm FA %u > max FA %u)\n",
1110 false_alarms
, max_false_alarms
);
1112 val
= data
->auto_corr_ofdm
+ AUTO_CORR_STEP_OFDM
;
1113 data
->auto_corr_ofdm
=
1114 min((u32
)AUTO_CORR_MAX_OFDM
, val
);
1116 val
= data
->auto_corr_ofdm_mrc
+ AUTO_CORR_STEP_OFDM
;
1117 data
->auto_corr_ofdm_mrc
=
1118 min((u32
)AUTO_CORR_MAX_OFDM_MRC
, val
);
1120 val
= data
->auto_corr_ofdm_x1
+ AUTO_CORR_STEP_OFDM
;
1121 data
->auto_corr_ofdm_x1
=
1122 min((u32
)AUTO_CORR_MAX_OFDM_X1
, val
);
1124 val
= data
->auto_corr_ofdm_mrc_x1
+ AUTO_CORR_STEP_OFDM
;
1125 data
->auto_corr_ofdm_mrc_x1
=
1126 min((u32
)AUTO_CORR_MAX_OFDM_MRC_X1
, val
);
1129 /* Else if we got fewer than desired, increase sensitivity */
1130 else if (false_alarms
< min_false_alarms
) {
1132 IWL_DEBUG_CALIB("norm FA %u < min FA %u\n",
1133 false_alarms
, min_false_alarms
);
1135 val
= data
->auto_corr_ofdm
- AUTO_CORR_STEP_OFDM
;
1136 data
->auto_corr_ofdm
=
1137 max((u32
)AUTO_CORR_MIN_OFDM
, val
);
1139 val
= data
->auto_corr_ofdm_mrc
- AUTO_CORR_STEP_OFDM
;
1140 data
->auto_corr_ofdm_mrc
=
1141 max((u32
)AUTO_CORR_MIN_OFDM_MRC
, val
);
1143 val
= data
->auto_corr_ofdm_x1
- AUTO_CORR_STEP_OFDM
;
1144 data
->auto_corr_ofdm_x1
=
1145 max((u32
)AUTO_CORR_MIN_OFDM_X1
, val
);
1147 val
= data
->auto_corr_ofdm_mrc_x1
- AUTO_CORR_STEP_OFDM
;
1148 data
->auto_corr_ofdm_mrc_x1
=
1149 max((u32
)AUTO_CORR_MIN_OFDM_MRC_X1
, val
);
1153 IWL_DEBUG_CALIB("min FA %u < norm FA %u < max FA %u OK\n",
1154 min_false_alarms
, false_alarms
, max_false_alarms
);
1159 static int iwl4965_sensitivity_callback(struct iwl_priv
*priv
,
1160 struct iwl4965_cmd
*cmd
, struct sk_buff
*skb
)
1162 /* We didn't cache the SKB; let the caller free it */
1166 /* Prepare a SENSITIVITY_CMD, send to uCode if values have changed */
1167 static int iwl4965_sensitivity_write(struct iwl_priv
*priv
, u8 flags
)
1170 struct iwl4965_sensitivity_cmd cmd
;
1171 struct iwl4965_sensitivity_data
*data
= NULL
;
1172 struct iwl4965_host_cmd cmd_out
= {
1173 .id
= SENSITIVITY_CMD
,
1174 .len
= sizeof(struct iwl4965_sensitivity_cmd
),
1175 .meta
.flags
= flags
,
1179 data
= &(priv
->sensitivity_data
);
1181 memset(&cmd
, 0, sizeof(cmd
));
1183 cmd
.table
[HD_AUTO_CORR32_X4_TH_ADD_MIN_INDEX
] =
1184 cpu_to_le16((u16
)data
->auto_corr_ofdm
);
1185 cmd
.table
[HD_AUTO_CORR32_X4_TH_ADD_MIN_MRC_INDEX
] =
1186 cpu_to_le16((u16
)data
->auto_corr_ofdm_mrc
);
1187 cmd
.table
[HD_AUTO_CORR32_X1_TH_ADD_MIN_INDEX
] =
1188 cpu_to_le16((u16
)data
->auto_corr_ofdm_x1
);
1189 cmd
.table
[HD_AUTO_CORR32_X1_TH_ADD_MIN_MRC_INDEX
] =
1190 cpu_to_le16((u16
)data
->auto_corr_ofdm_mrc_x1
);
1192 cmd
.table
[HD_AUTO_CORR40_X4_TH_ADD_MIN_INDEX
] =
1193 cpu_to_le16((u16
)data
->auto_corr_cck
);
1194 cmd
.table
[HD_AUTO_CORR40_X4_TH_ADD_MIN_MRC_INDEX
] =
1195 cpu_to_le16((u16
)data
->auto_corr_cck_mrc
);
1197 cmd
.table
[HD_MIN_ENERGY_CCK_DET_INDEX
] =
1198 cpu_to_le16((u16
)data
->nrg_th_cck
);
1199 cmd
.table
[HD_MIN_ENERGY_OFDM_DET_INDEX
] =
1200 cpu_to_le16((u16
)data
->nrg_th_ofdm
);
1202 cmd
.table
[HD_BARKER_CORR_TH_ADD_MIN_INDEX
] =
1203 __constant_cpu_to_le16(190);
1204 cmd
.table
[HD_BARKER_CORR_TH_ADD_MIN_MRC_INDEX
] =
1205 __constant_cpu_to_le16(390);
1206 cmd
.table
[HD_OFDM_ENERGY_TH_IN_INDEX
] =
1207 __constant_cpu_to_le16(62);
1209 IWL_DEBUG_CALIB("ofdm: ac %u mrc %u x1 %u mrc_x1 %u thresh %u\n",
1210 data
->auto_corr_ofdm
, data
->auto_corr_ofdm_mrc
,
1211 data
->auto_corr_ofdm_x1
, data
->auto_corr_ofdm_mrc_x1
,
1214 IWL_DEBUG_CALIB("cck: ac %u mrc %u thresh %u\n",
1215 data
->auto_corr_cck
, data
->auto_corr_cck_mrc
,
1218 /* Update uCode's "work" table, and copy it to DSP */
1219 cmd
.control
= SENSITIVITY_CMD_CONTROL_WORK_TABLE
;
1221 if (flags
& CMD_ASYNC
)
1222 cmd_out
.meta
.u
.callback
= iwl4965_sensitivity_callback
;
1224 /* Don't send command to uCode if nothing has changed */
1225 if (!memcmp(&cmd
.table
[0], &(priv
->sensitivity_tbl
[0]),
1226 sizeof(u16
)*HD_TABLE_SIZE
)) {
1227 IWL_DEBUG_CALIB("No change in SENSITIVITY_CMD\n");
1231 /* Copy table for comparison next time */
1232 memcpy(&(priv
->sensitivity_tbl
[0]), &(cmd
.table
[0]),
1233 sizeof(u16
)*HD_TABLE_SIZE
);
1235 rc
= iwl4965_send_cmd(priv
, &cmd_out
);
1237 IWL_DEBUG_CALIB("SENSITIVITY_CMD succeeded\n");
1244 void iwl4965_init_sensitivity(struct iwl_priv
*priv
, u8 flags
, u8 force
)
1248 struct iwl4965_sensitivity_data
*data
= NULL
;
1250 IWL_DEBUG_CALIB("Start iwl4965_init_sensitivity\n");
1253 memset(&(priv
->sensitivity_tbl
[0]), 0,
1254 sizeof(u16
)*HD_TABLE_SIZE
);
1256 /* Clear driver's sensitivity algo data */
1257 data
= &(priv
->sensitivity_data
);
1258 memset(data
, 0, sizeof(struct iwl4965_sensitivity_data
));
1260 data
->num_in_cck_no_fa
= 0;
1261 data
->nrg_curr_state
= IWL_FA_TOO_MANY
;
1262 data
->nrg_prev_state
= IWL_FA_TOO_MANY
;
1263 data
->nrg_silence_ref
= 0;
1264 data
->nrg_silence_idx
= 0;
1265 data
->nrg_energy_idx
= 0;
1267 for (i
= 0; i
< 10; i
++)
1268 data
->nrg_value
[i
] = 0;
1270 for (i
= 0; i
< NRG_NUM_PREV_STAT_L
; i
++)
1271 data
->nrg_silence_rssi
[i
] = 0;
1273 data
->auto_corr_ofdm
= 90;
1274 data
->auto_corr_ofdm_mrc
= 170;
1275 data
->auto_corr_ofdm_x1
= 105;
1276 data
->auto_corr_ofdm_mrc_x1
= 220;
1277 data
->auto_corr_cck
= AUTO_CORR_CCK_MIN_VAL_DEF
;
1278 data
->auto_corr_cck_mrc
= 200;
1279 data
->nrg_th_cck
= 100;
1280 data
->nrg_th_ofdm
= 100;
1282 data
->last_bad_plcp_cnt_ofdm
= 0;
1283 data
->last_fa_cnt_ofdm
= 0;
1284 data
->last_bad_plcp_cnt_cck
= 0;
1285 data
->last_fa_cnt_cck
= 0;
1287 /* Clear prior Sensitivity command data to force send to uCode */
1289 memset(&(priv
->sensitivity_tbl
[0]), 0,
1290 sizeof(u16
)*HD_TABLE_SIZE
);
1292 rc
|= iwl4965_sensitivity_write(priv
, flags
);
1293 IWL_DEBUG_CALIB("<<return 0x%X\n", rc
);
1299 /* Reset differential Rx gains in NIC to prepare for chain noise calibration.
1300 * Called after every association, but this runs only once!
1301 * ... once chain noise is calibrated the first time, it's good forever. */
1302 void iwl4965_chain_noise_reset(struct iwl_priv
*priv
)
1304 struct iwl4965_chain_noise_data
*data
= NULL
;
1307 data
= &(priv
->chain_noise_data
);
1308 if ((data
->state
== IWL_CHAIN_NOISE_ALIVE
) && iwl4965_is_associated(priv
)) {
1309 struct iwl4965_calibration_cmd cmd
;
1311 memset(&cmd
, 0, sizeof(cmd
));
1312 cmd
.opCode
= PHY_CALIBRATE_DIFF_GAIN_CMD
;
1313 cmd
.diff_gain_a
= 0;
1314 cmd
.diff_gain_b
= 0;
1315 cmd
.diff_gain_c
= 0;
1316 rc
= iwl4965_send_cmd_pdu(priv
, REPLY_PHY_CALIBRATION_CMD
,
1319 data
->state
= IWL_CHAIN_NOISE_ACCUMULATE
;
1320 IWL_DEBUG_CALIB("Run chain_noise_calibrate\n");
1326 * Accumulate 20 beacons of signal and noise statistics for each of
1327 * 3 receivers/antennas/rx-chains, then figure out:
1328 * 1) Which antennas are connected.
1329 * 2) Differential rx gain settings to balance the 3 receivers.
1331 static void iwl4965_noise_calibration(struct iwl_priv
*priv
,
1332 struct iwl4965_notif_statistics
*stat_resp
)
1334 struct iwl4965_chain_noise_data
*data
= NULL
;
1343 u32 average_sig
[NUM_RX_CHAINS
] = {INITIALIZATION_VALUE
};
1344 u32 average_noise
[NUM_RX_CHAINS
] = {INITIALIZATION_VALUE
};
1345 u32 max_average_sig
;
1346 u16 max_average_sig_antenna_i
;
1347 u32 min_average_noise
= MIN_AVERAGE_NOISE_MAX_VALUE
;
1348 u16 min_average_noise_antenna_i
= INITIALIZATION_VALUE
;
1350 u16 chan_num
= INITIALIZATION_VALUE
;
1351 u32 band
= INITIALIZATION_VALUE
;
1352 u32 active_chains
= 0;
1353 unsigned long flags
;
1354 struct statistics_rx_non_phy
*rx_info
= &(stat_resp
->rx
.general
);
1356 data
= &(priv
->chain_noise_data
);
1358 /* Accumulate just the first 20 beacons after the first association,
1359 * then we're done forever. */
1360 if (data
->state
!= IWL_CHAIN_NOISE_ACCUMULATE
) {
1361 if (data
->state
== IWL_CHAIN_NOISE_ALIVE
)
1362 IWL_DEBUG_CALIB("Wait for noise calib reset\n");
1366 spin_lock_irqsave(&priv
->lock
, flags
);
1367 if (rx_info
->interference_data_flag
!= INTERFERENCE_DATA_AVAILABLE
) {
1368 IWL_DEBUG_CALIB(" << Interference data unavailable\n");
1369 spin_unlock_irqrestore(&priv
->lock
, flags
);
1373 band
= (priv
->staging_rxon
.flags
& RXON_FLG_BAND_24G_MSK
) ? 0 : 1;
1374 chan_num
= le16_to_cpu(priv
->staging_rxon
.channel
);
1376 /* Make sure we accumulate data for just the associated channel
1377 * (even if scanning). */
1378 if ((chan_num
!= (le32_to_cpu(stat_resp
->flag
) >> 16)) ||
1379 ((STATISTICS_REPLY_FLG_BAND_24G_MSK
==
1380 (stat_resp
->flag
& STATISTICS_REPLY_FLG_BAND_24G_MSK
)) && band
)) {
1381 IWL_DEBUG_CALIB("Stats not from chan=%d, band=%d\n",
1383 spin_unlock_irqrestore(&priv
->lock
, flags
);
1387 /* Accumulate beacon statistics values across 20 beacons */
1388 chain_noise_a
= le32_to_cpu(rx_info
->beacon_silence_rssi_a
) &
1390 chain_noise_b
= le32_to_cpu(rx_info
->beacon_silence_rssi_b
) &
1392 chain_noise_c
= le32_to_cpu(rx_info
->beacon_silence_rssi_c
) &
1395 chain_sig_a
= le32_to_cpu(rx_info
->beacon_rssi_a
) & IN_BAND_FILTER
;
1396 chain_sig_b
= le32_to_cpu(rx_info
->beacon_rssi_b
) & IN_BAND_FILTER
;
1397 chain_sig_c
= le32_to_cpu(rx_info
->beacon_rssi_c
) & IN_BAND_FILTER
;
1399 spin_unlock_irqrestore(&priv
->lock
, flags
);
1401 data
->beacon_count
++;
1403 data
->chain_noise_a
= (chain_noise_a
+ data
->chain_noise_a
);
1404 data
->chain_noise_b
= (chain_noise_b
+ data
->chain_noise_b
);
1405 data
->chain_noise_c
= (chain_noise_c
+ data
->chain_noise_c
);
1407 data
->chain_signal_a
= (chain_sig_a
+ data
->chain_signal_a
);
1408 data
->chain_signal_b
= (chain_sig_b
+ data
->chain_signal_b
);
1409 data
->chain_signal_c
= (chain_sig_c
+ data
->chain_signal_c
);
1411 IWL_DEBUG_CALIB("chan=%d, band=%d, beacon=%d\n", chan_num
, band
,
1412 data
->beacon_count
);
1413 IWL_DEBUG_CALIB("chain_sig: a %d b %d c %d\n",
1414 chain_sig_a
, chain_sig_b
, chain_sig_c
);
1415 IWL_DEBUG_CALIB("chain_noise: a %d b %d c %d\n",
1416 chain_noise_a
, chain_noise_b
, chain_noise_c
);
1418 /* If this is the 20th beacon, determine:
1419 * 1) Disconnected antennas (using signal strengths)
1420 * 2) Differential gain (using silence noise) to balance receivers */
1421 if (data
->beacon_count
== CAL_NUM_OF_BEACONS
) {
1423 /* Analyze signal for disconnected antenna */
1424 average_sig
[0] = (data
->chain_signal_a
) / CAL_NUM_OF_BEACONS
;
1425 average_sig
[1] = (data
->chain_signal_b
) / CAL_NUM_OF_BEACONS
;
1426 average_sig
[2] = (data
->chain_signal_c
) / CAL_NUM_OF_BEACONS
;
1428 if (average_sig
[0] >= average_sig
[1]) {
1429 max_average_sig
= average_sig
[0];
1430 max_average_sig_antenna_i
= 0;
1431 active_chains
= (1 << max_average_sig_antenna_i
);
1433 max_average_sig
= average_sig
[1];
1434 max_average_sig_antenna_i
= 1;
1435 active_chains
= (1 << max_average_sig_antenna_i
);
1438 if (average_sig
[2] >= max_average_sig
) {
1439 max_average_sig
= average_sig
[2];
1440 max_average_sig_antenna_i
= 2;
1441 active_chains
= (1 << max_average_sig_antenna_i
);
1444 IWL_DEBUG_CALIB("average_sig: a %d b %d c %d\n",
1445 average_sig
[0], average_sig
[1], average_sig
[2]);
1446 IWL_DEBUG_CALIB("max_average_sig = %d, antenna %d\n",
1447 max_average_sig
, max_average_sig_antenna_i
);
1449 /* Compare signal strengths for all 3 receivers. */
1450 for (i
= 0; i
< NUM_RX_CHAINS
; i
++) {
1451 if (i
!= max_average_sig_antenna_i
) {
1452 s32 rssi_delta
= (max_average_sig
-
1455 /* If signal is very weak, compared with
1456 * strongest, mark it as disconnected. */
1457 if (rssi_delta
> MAXIMUM_ALLOWED_PATHLOSS
)
1458 data
->disconn_array
[i
] = 1;
1460 active_chains
|= (1 << i
);
1461 IWL_DEBUG_CALIB("i = %d rssiDelta = %d "
1462 "disconn_array[i] = %d\n",
1463 i
, rssi_delta
, data
->disconn_array
[i
]);
1467 /*If both chains A & B are disconnected -
1468 * connect B and leave A as is */
1469 if (data
->disconn_array
[CHAIN_A
] &&
1470 data
->disconn_array
[CHAIN_B
]) {
1471 data
->disconn_array
[CHAIN_B
] = 0;
1472 active_chains
|= (1 << CHAIN_B
);
1473 IWL_DEBUG_CALIB("both A & B chains are disconnected! "
1474 "W/A - declare B as connected\n");
1477 IWL_DEBUG_CALIB("active_chains (bitwise) = 0x%x\n",
1480 /* Save for use within RXON, TX, SCAN commands, etc. */
1481 priv
->valid_antenna
= active_chains
;
1483 /* Analyze noise for rx balance */
1484 average_noise
[0] = ((data
->chain_noise_a
)/CAL_NUM_OF_BEACONS
);
1485 average_noise
[1] = ((data
->chain_noise_b
)/CAL_NUM_OF_BEACONS
);
1486 average_noise
[2] = ((data
->chain_noise_c
)/CAL_NUM_OF_BEACONS
);
1488 for (i
= 0; i
< NUM_RX_CHAINS
; i
++) {
1489 if (!(data
->disconn_array
[i
]) &&
1490 (average_noise
[i
] <= min_average_noise
)) {
1491 /* This means that chain i is active and has
1492 * lower noise values so far: */
1493 min_average_noise
= average_noise
[i
];
1494 min_average_noise_antenna_i
= i
;
1498 data
->delta_gain_code
[min_average_noise_antenna_i
] = 0;
1500 IWL_DEBUG_CALIB("average_noise: a %d b %d c %d\n",
1501 average_noise
[0], average_noise
[1],
1504 IWL_DEBUG_CALIB("min_average_noise = %d, antenna %d\n",
1505 min_average_noise
, min_average_noise_antenna_i
);
1507 for (i
= 0; i
< NUM_RX_CHAINS
; i
++) {
1510 if (!(data
->disconn_array
[i
]) &&
1511 (data
->delta_gain_code
[i
] ==
1512 CHAIN_NOISE_DELTA_GAIN_INIT_VAL
)) {
1513 delta_g
= average_noise
[i
] - min_average_noise
;
1514 data
->delta_gain_code
[i
] = (u8
)((delta_g
*
1516 if (CHAIN_NOISE_MAX_DELTA_GAIN_CODE
<
1517 data
->delta_gain_code
[i
])
1518 data
->delta_gain_code
[i
] =
1519 CHAIN_NOISE_MAX_DELTA_GAIN_CODE
;
1521 data
->delta_gain_code
[i
] =
1522 (data
->delta_gain_code
[i
] | (1 << 2));
1524 data
->delta_gain_code
[i
] = 0;
1526 IWL_DEBUG_CALIB("delta_gain_codes: a %d b %d c %d\n",
1527 data
->delta_gain_code
[0],
1528 data
->delta_gain_code
[1],
1529 data
->delta_gain_code
[2]);
1531 /* Differential gain gets sent to uCode only once */
1532 if (!data
->radio_write
) {
1533 struct iwl4965_calibration_cmd cmd
;
1534 data
->radio_write
= 1;
1536 memset(&cmd
, 0, sizeof(cmd
));
1537 cmd
.opCode
= PHY_CALIBRATE_DIFF_GAIN_CMD
;
1538 cmd
.diff_gain_a
= data
->delta_gain_code
[0];
1539 cmd
.diff_gain_b
= data
->delta_gain_code
[1];
1540 cmd
.diff_gain_c
= data
->delta_gain_code
[2];
1541 rc
= iwl4965_send_cmd_pdu(priv
, REPLY_PHY_CALIBRATION_CMD
,
1544 IWL_DEBUG_CALIB("fail sending cmd "
1545 "REPLY_PHY_CALIBRATION_CMD \n");
1547 /* TODO we might want recalculate
1548 * rx_chain in rxon cmd */
1550 /* Mark so we run this algo only once! */
1551 data
->state
= IWL_CHAIN_NOISE_CALIBRATED
;
1553 data
->chain_noise_a
= 0;
1554 data
->chain_noise_b
= 0;
1555 data
->chain_noise_c
= 0;
1556 data
->chain_signal_a
= 0;
1557 data
->chain_signal_b
= 0;
1558 data
->chain_signal_c
= 0;
1559 data
->beacon_count
= 0;
1564 static void iwl4965_sensitivity_calibration(struct iwl_priv
*priv
,
1565 struct iwl4965_notif_statistics
*resp
)
1575 struct iwl4965_sensitivity_data
*data
= NULL
;
1576 struct statistics_rx_non_phy
*rx_info
= &(resp
->rx
.general
);
1577 struct statistics_rx
*statistics
= &(resp
->rx
);
1578 unsigned long flags
;
1579 struct statistics_general_data statis
;
1581 data
= &(priv
->sensitivity_data
);
1583 if (!iwl4965_is_associated(priv
)) {
1584 IWL_DEBUG_CALIB("<< - not associated\n");
1588 spin_lock_irqsave(&priv
->lock
, flags
);
1589 if (rx_info
->interference_data_flag
!= INTERFERENCE_DATA_AVAILABLE
) {
1590 IWL_DEBUG_CALIB("<< invalid data.\n");
1591 spin_unlock_irqrestore(&priv
->lock
, flags
);
1595 /* Extract Statistics: */
1596 rx_enable_time
= le32_to_cpu(rx_info
->channel_load
);
1597 fa_cck
= le32_to_cpu(statistics
->cck
.false_alarm_cnt
);
1598 fa_ofdm
= le32_to_cpu(statistics
->ofdm
.false_alarm_cnt
);
1599 bad_plcp_cck
= le32_to_cpu(statistics
->cck
.plcp_err
);
1600 bad_plcp_ofdm
= le32_to_cpu(statistics
->ofdm
.plcp_err
);
1602 statis
.beacon_silence_rssi_a
=
1603 le32_to_cpu(statistics
->general
.beacon_silence_rssi_a
);
1604 statis
.beacon_silence_rssi_b
=
1605 le32_to_cpu(statistics
->general
.beacon_silence_rssi_b
);
1606 statis
.beacon_silence_rssi_c
=
1607 le32_to_cpu(statistics
->general
.beacon_silence_rssi_c
);
1608 statis
.beacon_energy_a
=
1609 le32_to_cpu(statistics
->general
.beacon_energy_a
);
1610 statis
.beacon_energy_b
=
1611 le32_to_cpu(statistics
->general
.beacon_energy_b
);
1612 statis
.beacon_energy_c
=
1613 le32_to_cpu(statistics
->general
.beacon_energy_c
);
1615 spin_unlock_irqrestore(&priv
->lock
, flags
);
1617 IWL_DEBUG_CALIB("rx_enable_time = %u usecs\n", rx_enable_time
);
1619 if (!rx_enable_time
) {
1620 IWL_DEBUG_CALIB("<< RX Enable Time == 0! \n");
1624 /* These statistics increase monotonically, and do not reset
1625 * at each beacon. Calculate difference from last value, or just
1626 * use the new statistics value if it has reset or wrapped around. */
1627 if (data
->last_bad_plcp_cnt_cck
> bad_plcp_cck
)
1628 data
->last_bad_plcp_cnt_cck
= bad_plcp_cck
;
1630 bad_plcp_cck
-= data
->last_bad_plcp_cnt_cck
;
1631 data
->last_bad_plcp_cnt_cck
+= bad_plcp_cck
;
1634 if (data
->last_bad_plcp_cnt_ofdm
> bad_plcp_ofdm
)
1635 data
->last_bad_plcp_cnt_ofdm
= bad_plcp_ofdm
;
1637 bad_plcp_ofdm
-= data
->last_bad_plcp_cnt_ofdm
;
1638 data
->last_bad_plcp_cnt_ofdm
+= bad_plcp_ofdm
;
1641 if (data
->last_fa_cnt_ofdm
> fa_ofdm
)
1642 data
->last_fa_cnt_ofdm
= fa_ofdm
;
1644 fa_ofdm
-= data
->last_fa_cnt_ofdm
;
1645 data
->last_fa_cnt_ofdm
+= fa_ofdm
;
1648 if (data
->last_fa_cnt_cck
> fa_cck
)
1649 data
->last_fa_cnt_cck
= fa_cck
;
1651 fa_cck
-= data
->last_fa_cnt_cck
;
1652 data
->last_fa_cnt_cck
+= fa_cck
;
1655 /* Total aborted signal locks */
1656 norm_fa_ofdm
= fa_ofdm
+ bad_plcp_ofdm
;
1657 norm_fa_cck
= fa_cck
+ bad_plcp_cck
;
1659 IWL_DEBUG_CALIB("cck: fa %u badp %u ofdm: fa %u badp %u\n", fa_cck
,
1660 bad_plcp_cck
, fa_ofdm
, bad_plcp_ofdm
);
1662 iwl4965_sens_auto_corr_ofdm(priv
, norm_fa_ofdm
, rx_enable_time
);
1663 iwl4965_sens_energy_cck(priv
, norm_fa_cck
, rx_enable_time
, &statis
);
1664 rc
|= iwl4965_sensitivity_write(priv
, CMD_ASYNC
);
1669 static void iwl4965_bg_sensitivity_work(struct work_struct
*work
)
1671 struct iwl_priv
*priv
= container_of(work
, struct iwl_priv
,
1674 mutex_lock(&priv
->mutex
);
1676 if (test_bit(STATUS_EXIT_PENDING
, &priv
->status
) ||
1677 test_bit(STATUS_SCANNING
, &priv
->status
)) {
1678 mutex_unlock(&priv
->mutex
);
1682 if (priv
->start_calib
) {
1683 iwl4965_noise_calibration(priv
, &priv
->statistics
);
1685 if (priv
->sensitivity_data
.state
==
1686 IWL_SENS_CALIB_NEED_REINIT
) {
1687 iwl4965_init_sensitivity(priv
, CMD_ASYNC
, 0);
1688 priv
->sensitivity_data
.state
= IWL_SENS_CALIB_ALLOWED
;
1690 iwl4965_sensitivity_calibration(priv
,
1694 mutex_unlock(&priv
->mutex
);
1697 #endif /*CONFIG_IWL4965_SENSITIVITY*/
1699 static void iwl4965_bg_txpower_work(struct work_struct
*work
)
1701 struct iwl_priv
*priv
= container_of(work
, struct iwl_priv
,
1704 /* If a scan happened to start before we got here
1705 * then just return; the statistics notification will
1706 * kick off another scheduled work to compensate for
1707 * any temperature delta we missed here. */
1708 if (test_bit(STATUS_EXIT_PENDING
, &priv
->status
) ||
1709 test_bit(STATUS_SCANNING
, &priv
->status
))
1712 mutex_lock(&priv
->mutex
);
1714 /* Regardless of if we are assocaited, we must reconfigure the
1715 * TX power since frames can be sent on non-radar channels while
1717 iwl4965_hw_reg_send_txpower(priv
);
1719 /* Update last_temperature to keep is_calib_needed from running
1720 * when it isn't needed... */
1721 priv
->last_temperature
= priv
->temperature
;
1723 mutex_unlock(&priv
->mutex
);
1727 * Acquire priv->lock before calling this function !
1729 static void iwl4965_set_wr_ptrs(struct iwl_priv
*priv
, int txq_id
, u32 index
)
1731 iwl4965_write_direct32(priv
, HBUS_TARG_WRPTR
,
1732 (index
& 0xff) | (txq_id
<< 8));
1733 iwl4965_write_prph(priv
, KDR_SCD_QUEUE_RDPTR(txq_id
), index
);
1737 * iwl4965_tx_queue_set_status - (optionally) start Tx/Cmd queue
1738 * @tx_fifo_id: Tx DMA/FIFO channel (range 0-7) that the queue will feed
1739 * @scd_retry: (1) Indicates queue will be used in aggregation mode
1741 * NOTE: Acquire priv->lock before calling this function !
1743 static void iwl4965_tx_queue_set_status(struct iwl_priv
*priv
,
1744 struct iwl4965_tx_queue
*txq
,
1745 int tx_fifo_id
, int scd_retry
)
1747 int txq_id
= txq
->q
.id
;
1749 /* Find out whether to activate Tx queue */
1750 int active
= test_bit(txq_id
, &priv
->txq_ctx_active_msk
)?1:0;
1752 /* Set up and activate */
1753 iwl4965_write_prph(priv
, KDR_SCD_QUEUE_STATUS_BITS(txq_id
),
1754 (active
<< SCD_QUEUE_STTS_REG_POS_ACTIVE
) |
1755 (tx_fifo_id
<< SCD_QUEUE_STTS_REG_POS_TXF
) |
1756 (scd_retry
<< SCD_QUEUE_STTS_REG_POS_WSL
) |
1757 (scd_retry
<< SCD_QUEUE_STTS_REG_POS_SCD_ACK
) |
1758 SCD_QUEUE_STTS_REG_MSK
);
1760 txq
->sched_retry
= scd_retry
;
1762 IWL_DEBUG_INFO("%s %s Queue %d on AC %d\n",
1763 active
? "Activate" : "Deactivate",
1764 scd_retry
? "BA" : "AC", txq_id
, tx_fifo_id
);
1767 static const u16 default_queue_to_tx_fifo
[] = {
1777 static inline void iwl4965_txq_ctx_activate(struct iwl_priv
*priv
, int txq_id
)
1779 set_bit(txq_id
, &priv
->txq_ctx_active_msk
);
1782 static inline void iwl4965_txq_ctx_deactivate(struct iwl_priv
*priv
, int txq_id
)
1784 clear_bit(txq_id
, &priv
->txq_ctx_active_msk
);
1787 int iwl4965_alive_notify(struct iwl_priv
*priv
)
1791 unsigned long flags
;
1794 spin_lock_irqsave(&priv
->lock
, flags
);
1796 #ifdef CONFIG_IWL4965_SENSITIVITY
1797 memset(&(priv
->sensitivity_data
), 0,
1798 sizeof(struct iwl4965_sensitivity_data
));
1799 memset(&(priv
->chain_noise_data
), 0,
1800 sizeof(struct iwl4965_chain_noise_data
));
1801 for (i
= 0; i
< NUM_RX_CHAINS
; i
++)
1802 priv
->chain_noise_data
.delta_gain_code
[i
] =
1803 CHAIN_NOISE_DELTA_GAIN_INIT_VAL
;
1804 #endif /* CONFIG_IWL4965_SENSITIVITY*/
1805 rc
= iwl4965_grab_nic_access(priv
);
1807 spin_unlock_irqrestore(&priv
->lock
, flags
);
1811 /* Clear 4965's internal Tx Scheduler data base */
1812 priv
->scd_base_addr
= iwl4965_read_prph(priv
, KDR_SCD_SRAM_BASE_ADDR
);
1813 a
= priv
->scd_base_addr
+ SCD_CONTEXT_DATA_OFFSET
;
1814 for (; a
< priv
->scd_base_addr
+ SCD_TX_STTS_BITMAP_OFFSET
; a
+= 4)
1815 iwl4965_write_targ_mem(priv
, a
, 0);
1816 for (; a
< priv
->scd_base_addr
+ SCD_TRANSLATE_TBL_OFFSET
; a
+= 4)
1817 iwl4965_write_targ_mem(priv
, a
, 0);
1818 for (; a
< sizeof(u16
) * priv
->hw_setting
.max_txq_num
; a
+= 4)
1819 iwl4965_write_targ_mem(priv
, a
, 0);
1821 /* Tel 4965 where to find Tx byte count tables */
1822 iwl4965_write_prph(priv
, KDR_SCD_DRAM_BASE_ADDR
,
1823 (priv
->hw_setting
.shared_phys
+
1824 offsetof(struct iwl4965_shared
, queues_byte_cnt_tbls
)) >> 10);
1826 /* Disable chain mode for all queues */
1827 iwl4965_write_prph(priv
, KDR_SCD_QUEUECHAIN_SEL
, 0);
1829 /* Initialize each Tx queue (including the command queue) */
1830 for (i
= 0; i
< priv
->hw_setting
.max_txq_num
; i
++) {
1832 /* TFD circular buffer read/write indexes */
1833 iwl4965_write_prph(priv
, KDR_SCD_QUEUE_RDPTR(i
), 0);
1834 iwl4965_write_direct32(priv
, HBUS_TARG_WRPTR
, 0 | (i
<< 8));
1836 /* Max Tx Window size for Scheduler-ACK mode */
1837 iwl4965_write_targ_mem(priv
, priv
->scd_base_addr
+
1838 SCD_CONTEXT_QUEUE_OFFSET(i
),
1840 SCD_QUEUE_CTX_REG1_WIN_SIZE_POS
) &
1841 SCD_QUEUE_CTX_REG1_WIN_SIZE_MSK
);
1844 iwl4965_write_targ_mem(priv
, priv
->scd_base_addr
+
1845 SCD_CONTEXT_QUEUE_OFFSET(i
) +
1848 SCD_QUEUE_CTX_REG2_FRAME_LIMIT_POS
) &
1849 SCD_QUEUE_CTX_REG2_FRAME_LIMIT_MSK
);
1852 iwl4965_write_prph(priv
, KDR_SCD_INTERRUPT_MASK
,
1853 (1 << priv
->hw_setting
.max_txq_num
) - 1);
1855 /* Activate all Tx DMA/FIFO channels */
1856 iwl4965_write_prph(priv
, KDR_SCD_TXFACT
,
1857 SCD_TXFACT_REG_TXFIFO_MASK(0, 7));
1859 iwl4965_set_wr_ptrs(priv
, IWL_CMD_QUEUE_NUM
, 0);
1861 /* Map each Tx/cmd queue to its corresponding fifo */
1862 for (i
= 0; i
< ARRAY_SIZE(default_queue_to_tx_fifo
); i
++) {
1863 int ac
= default_queue_to_tx_fifo
[i
];
1864 iwl4965_txq_ctx_activate(priv
, i
);
1865 iwl4965_tx_queue_set_status(priv
, &priv
->txq
[i
], ac
, 0);
1868 iwl4965_release_nic_access(priv
);
1869 spin_unlock_irqrestore(&priv
->lock
, flags
);
1875 * iwl4965_hw_set_hw_setting
1877 * Called when initializing driver
1879 int iwl4965_hw_set_hw_setting(struct iwl_priv
*priv
)
1883 if ((iwl4965_mod_params
.num_of_queues
> IWL_MAX_NUM_QUEUES
) ||
1884 (iwl4965_mod_params
.num_of_queues
< IWL_MIN_NUM_QUEUES
)) {
1885 IWL_ERROR("invalid queues_num, should be between %d and %d\n",
1886 IWL_MIN_NUM_QUEUES
, IWL_MAX_NUM_QUEUES
);
1891 /* Allocate area for Tx byte count tables and Rx queue status */
1892 priv
->hw_setting
.shared_virt
=
1893 pci_alloc_consistent(priv
->pci_dev
,
1894 sizeof(struct iwl4965_shared
),
1895 &priv
->hw_setting
.shared_phys
);
1897 if (!priv
->hw_setting
.shared_virt
) {
1902 memset(priv
->hw_setting
.shared_virt
, 0, sizeof(struct iwl4965_shared
));
1904 priv
->hw_setting
.max_txq_num
= iwl4965_mod_params
.num_of_queues
;
1905 priv
->hw_setting
.tx_cmd_len
= sizeof(struct iwl4965_tx_cmd
);
1906 priv
->hw_setting
.max_rxq_size
= RX_QUEUE_SIZE
;
1907 priv
->hw_setting
.max_rxq_log
= RX_QUEUE_SIZE_LOG
;
1908 if (iwl4965_mod_params
.amsdu_size_8K
)
1909 priv
->hw_setting
.rx_buf_size
= IWL_RX_BUF_SIZE_8K
;
1911 priv
->hw_setting
.rx_buf_size
= IWL_RX_BUF_SIZE_4K
;
1912 priv
->hw_setting
.max_pkt_size
= priv
->hw_setting
.rx_buf_size
- 256;
1913 priv
->hw_setting
.max_stations
= IWL4965_STATION_COUNT
;
1914 priv
->hw_setting
.bcast_sta_id
= IWL4965_BROADCAST_ID
;
1916 priv
->hw_setting
.tx_ant_num
= 2;
1923 * iwl4965_hw_txq_ctx_free - Free TXQ Context
1925 * Destroy all TX DMA queues and structures
1927 void iwl4965_hw_txq_ctx_free(struct iwl_priv
*priv
)
1932 for (txq_id
= 0; txq_id
< priv
->hw_setting
.max_txq_num
; txq_id
++)
1933 iwl4965_tx_queue_free(priv
, &priv
->txq
[txq_id
]);
1935 /* Keep-warm buffer */
1936 iwl4965_kw_free(priv
);
1940 * iwl4965_hw_txq_free_tfd - Free all chunks referenced by TFD [txq->q.read_ptr]
1942 * Does NOT advance any TFD circular buffer read/write indexes
1943 * Does NOT free the TFD itself (which is within circular buffer)
1945 int iwl4965_hw_txq_free_tfd(struct iwl_priv
*priv
, struct iwl4965_tx_queue
*txq
)
1947 struct iwl4965_tfd_frame
*bd_tmp
= (struct iwl4965_tfd_frame
*)&txq
->bd
[0];
1948 struct iwl4965_tfd_frame
*bd
= &bd_tmp
[txq
->q
.read_ptr
];
1949 struct pci_dev
*dev
= priv
->pci_dev
;
1954 /* Host command buffers stay mapped in memory, nothing to clean */
1955 if (txq
->q
.id
== IWL_CMD_QUEUE_NUM
)
1958 /* Sanity check on number of chunks */
1959 counter
= IWL_GET_BITS(*bd
, num_tbs
);
1960 if (counter
> MAX_NUM_OF_TBS
) {
1961 IWL_ERROR("Too many chunks: %i\n", counter
);
1962 /* @todo issue fatal error, it is quite serious situation */
1966 /* Unmap chunks, if any.
1967 * TFD info for odd chunks is different format than for even chunks. */
1968 for (i
= 0; i
< counter
; i
++) {
1975 IWL_GET_BITS(bd
->pa
[index
], tb2_addr_lo16
) |
1976 (IWL_GET_BITS(bd
->pa
[index
],
1977 tb2_addr_hi20
) << 16),
1978 IWL_GET_BITS(bd
->pa
[index
], tb2_len
),
1982 pci_unmap_single(dev
,
1983 le32_to_cpu(bd
->pa
[index
].tb1_addr
),
1984 IWL_GET_BITS(bd
->pa
[index
], tb1_len
),
1987 /* Free SKB, if any, for this chunk */
1988 if (txq
->txb
[txq
->q
.read_ptr
].skb
[i
]) {
1989 struct sk_buff
*skb
= txq
->txb
[txq
->q
.read_ptr
].skb
[i
];
1992 txq
->txb
[txq
->q
.read_ptr
].skb
[i
] = NULL
;
1998 int iwl4965_hw_reg_set_txpower(struct iwl_priv
*priv
, s8 power
)
2000 IWL_ERROR("TODO: Implement iwl4965_hw_reg_set_txpower!\n");
2004 static s32
iwl4965_math_div_round(s32 num
, s32 denom
, s32
*res
)
2017 *res
= ((num
* 2 + denom
) / (denom
* 2)) * sign
;
2023 * iwl4965_get_voltage_compensation - Power supply voltage comp for txpower
2025 * Determines power supply voltage compensation for txpower calculations.
2026 * Returns number of 1/2-dB steps to subtract from gain table index,
2027 * to compensate for difference between power supply voltage during
2028 * factory measurements, vs. current power supply voltage.
2030 * Voltage indication is higher for lower voltage.
2031 * Lower voltage requires more gain (lower gain table index).
2033 static s32
iwl4965_get_voltage_compensation(s32 eeprom_voltage
,
2034 s32 current_voltage
)
2038 if ((TX_POWER_IWL_ILLEGAL_VOLTAGE
== eeprom_voltage
) ||
2039 (TX_POWER_IWL_ILLEGAL_VOLTAGE
== current_voltage
))
2042 iwl4965_math_div_round(current_voltage
- eeprom_voltage
,
2043 TX_POWER_IWL_VOLTAGE_CODES_PER_03V
, &comp
);
2045 if (current_voltage
> eeprom_voltage
)
2047 if ((comp
< -2) || (comp
> 2))
2053 static const struct iwl_channel_info
*
2054 iwl4965_get_channel_txpower_info(struct iwl_priv
*priv
,
2055 enum ieee80211_band band
, u16 channel
)
2057 const struct iwl_channel_info
*ch_info
;
2059 ch_info
= iwl4965_get_channel_info(priv
, band
, channel
);
2061 if (!is_channel_valid(ch_info
))
2067 static s32
iwl4965_get_tx_atten_grp(u16 channel
)
2069 if (channel
>= CALIB_IWL_TX_ATTEN_GR5_FCH
&&
2070 channel
<= CALIB_IWL_TX_ATTEN_GR5_LCH
)
2071 return CALIB_CH_GROUP_5
;
2073 if (channel
>= CALIB_IWL_TX_ATTEN_GR1_FCH
&&
2074 channel
<= CALIB_IWL_TX_ATTEN_GR1_LCH
)
2075 return CALIB_CH_GROUP_1
;
2077 if (channel
>= CALIB_IWL_TX_ATTEN_GR2_FCH
&&
2078 channel
<= CALIB_IWL_TX_ATTEN_GR2_LCH
)
2079 return CALIB_CH_GROUP_2
;
2081 if (channel
>= CALIB_IWL_TX_ATTEN_GR3_FCH
&&
2082 channel
<= CALIB_IWL_TX_ATTEN_GR3_LCH
)
2083 return CALIB_CH_GROUP_3
;
2085 if (channel
>= CALIB_IWL_TX_ATTEN_GR4_FCH
&&
2086 channel
<= CALIB_IWL_TX_ATTEN_GR4_LCH
)
2087 return CALIB_CH_GROUP_4
;
2089 IWL_ERROR("Can't find txatten group for channel %d.\n", channel
);
2093 static u32
iwl4965_get_sub_band(const struct iwl_priv
*priv
, u32 channel
)
2097 for (b
= 0; b
< EEPROM_TX_POWER_BANDS
; b
++) {
2098 if (priv
->eeprom
.calib_info
.band_info
[b
].ch_from
== 0)
2101 if ((channel
>= priv
->eeprom
.calib_info
.band_info
[b
].ch_from
)
2102 && (channel
<= priv
->eeprom
.calib_info
.band_info
[b
].ch_to
))
2109 static s32
iwl4965_interpolate_value(s32 x
, s32 x1
, s32 y1
, s32 x2
, s32 y2
)
2116 iwl4965_math_div_round((x2
- x
) * (y1
- y2
), (x2
- x1
), &val
);
2122 * iwl4965_interpolate_chan - Interpolate factory measurements for one channel
2124 * Interpolates factory measurements from the two sample channels within a
2125 * sub-band, to apply to channel of interest. Interpolation is proportional to
2126 * differences in channel frequencies, which is proportional to differences
2127 * in channel number.
2129 static int iwl4965_interpolate_chan(struct iwl_priv
*priv
, u32 channel
,
2130 struct iwl4965_eeprom_calib_ch_info
*chan_info
)
2135 const struct iwl4965_eeprom_calib_measure
*m1
;
2136 const struct iwl4965_eeprom_calib_measure
*m2
;
2137 struct iwl4965_eeprom_calib_measure
*omeas
;
2141 s
= iwl4965_get_sub_band(priv
, channel
);
2142 if (s
>= EEPROM_TX_POWER_BANDS
) {
2143 IWL_ERROR("Tx Power can not find channel %d ", channel
);
2147 ch_i1
= priv
->eeprom
.calib_info
.band_info
[s
].ch1
.ch_num
;
2148 ch_i2
= priv
->eeprom
.calib_info
.band_info
[s
].ch2
.ch_num
;
2149 chan_info
->ch_num
= (u8
) channel
;
2151 IWL_DEBUG_TXPOWER("channel %d subband %d factory cal ch %d & %d\n",
2152 channel
, s
, ch_i1
, ch_i2
);
2154 for (c
= 0; c
< EEPROM_TX_POWER_TX_CHAINS
; c
++) {
2155 for (m
= 0; m
< EEPROM_TX_POWER_MEASUREMENTS
; m
++) {
2156 m1
= &(priv
->eeprom
.calib_info
.band_info
[s
].ch1
.
2157 measurements
[c
][m
]);
2158 m2
= &(priv
->eeprom
.calib_info
.band_info
[s
].ch2
.
2159 measurements
[c
][m
]);
2160 omeas
= &(chan_info
->measurements
[c
][m
]);
2163 (u8
) iwl4965_interpolate_value(channel
, ch_i1
,
2168 (u8
) iwl4965_interpolate_value(channel
, ch_i1
,
2169 m1
->gain_idx
, ch_i2
,
2171 omeas
->temperature
=
2172 (u8
) iwl4965_interpolate_value(channel
, ch_i1
,
2177 (s8
) iwl4965_interpolate_value(channel
, ch_i1
,
2182 ("chain %d meas %d AP1=%d AP2=%d AP=%d\n", c
, m
,
2183 m1
->actual_pow
, m2
->actual_pow
, omeas
->actual_pow
);
2185 ("chain %d meas %d NI1=%d NI2=%d NI=%d\n", c
, m
,
2186 m1
->gain_idx
, m2
->gain_idx
, omeas
->gain_idx
);
2188 ("chain %d meas %d PA1=%d PA2=%d PA=%d\n", c
, m
,
2189 m1
->pa_det
, m2
->pa_det
, omeas
->pa_det
);
2191 ("chain %d meas %d T1=%d T2=%d T=%d\n", c
, m
,
2192 m1
->temperature
, m2
->temperature
,
2193 omeas
->temperature
);
2200 /* bit-rate-dependent table to prevent Tx distortion, in half-dB units,
2201 * for OFDM 6, 12, 18, 24, 36, 48, 54, 60 MBit, and CCK all rates. */
2202 static s32 back_off_table
[] = {
2203 10, 10, 10, 10, 10, 15, 17, 20, /* OFDM SISO 20 MHz */
2204 10, 10, 10, 10, 10, 15, 17, 20, /* OFDM MIMO 20 MHz */
2205 10, 10, 10, 10, 10, 15, 17, 20, /* OFDM SISO 40 MHz */
2206 10, 10, 10, 10, 10, 15, 17, 20, /* OFDM MIMO 40 MHz */
2210 /* Thermal compensation values for txpower for various frequency ranges ...
2211 * ratios from 3:1 to 4.5:1 of degrees (Celsius) per half-dB gain adjust */
2212 static struct iwl4965_txpower_comp_entry
{
2213 s32 degrees_per_05db_a
;
2214 s32 degrees_per_05db_a_denom
;
2215 } tx_power_cmp_tble
[CALIB_CH_GROUP_MAX
] = {
2216 {9, 2}, /* group 0 5.2, ch 34-43 */
2217 {4, 1}, /* group 1 5.2, ch 44-70 */
2218 {4, 1}, /* group 2 5.2, ch 71-124 */
2219 {4, 1}, /* group 3 5.2, ch 125-200 */
2220 {3, 1} /* group 4 2.4, ch all */
2223 static s32
get_min_power_index(s32 rate_power_index
, u32 band
)
2226 if ((rate_power_index
& 7) <= 4)
2227 return MIN_TX_GAIN_INDEX_52GHZ_EXT
;
2229 return MIN_TX_GAIN_INDEX
;
2237 static const struct gain_entry gain_table
[2][108] = {
2238 /* 5.2GHz power gain index table */
2240 {123, 0x3F}, /* highest txpower */
2349 /* 2.4GHz power gain index table */
2351 {110, 0x3f}, /* highest txpower */
2462 static int iwl4965_fill_txpower_tbl(struct iwl_priv
*priv
, u8 band
, u16 channel
,
2463 u8 is_fat
, u8 ctrl_chan_high
,
2464 struct iwl4965_tx_power_db
*tx_power_tbl
)
2466 u8 saturation_power
;
2468 s32 user_target_power
;
2472 s32 current_regulatory
;
2473 s32 txatten_grp
= CALIB_CH_GROUP_MAX
;
2476 const struct iwl_channel_info
*ch_info
= NULL
;
2477 struct iwl4965_eeprom_calib_ch_info ch_eeprom_info
;
2478 const struct iwl4965_eeprom_calib_measure
*measurement
;
2481 s32 voltage_compensation
;
2482 s32 degrees_per_05db_num
;
2483 s32 degrees_per_05db_denom
;
2485 s32 temperature_comp
[2];
2486 s32 factory_gain_index
[2];
2487 s32 factory_actual_pwr
[2];
2490 /* Sanity check requested level (dBm) */
2491 if (priv
->user_txpower_limit
< IWL_TX_POWER_TARGET_POWER_MIN
) {
2492 IWL_WARNING("Requested user TXPOWER %d below limit.\n",
2493 priv
->user_txpower_limit
);
2496 if (priv
->user_txpower_limit
> IWL_TX_POWER_TARGET_POWER_MAX
) {
2497 IWL_WARNING("Requested user TXPOWER %d above limit.\n",
2498 priv
->user_txpower_limit
);
2502 /* user_txpower_limit is in dBm, convert to half-dBm (half-dB units
2503 * are used for indexing into txpower table) */
2504 user_target_power
= 2 * priv
->user_txpower_limit
;
2506 /* Get current (RXON) channel, band, width */
2508 iwl4965_get_channel_txpower_info(priv
, priv
->band
, channel
);
2510 IWL_DEBUG_TXPOWER("chan %d band %d is_fat %d\n", channel
, band
,
2516 /* get txatten group, used to select 1) thermal txpower adjustment
2517 * and 2) mimo txpower balance between Tx chains. */
2518 txatten_grp
= iwl4965_get_tx_atten_grp(channel
);
2519 if (txatten_grp
< 0)
2522 IWL_DEBUG_TXPOWER("channel %d belongs to txatten group %d\n",
2523 channel
, txatten_grp
);
2532 /* hardware txpower limits ...
2533 * saturation (clipping distortion) txpowers are in half-dBm */
2535 saturation_power
= priv
->eeprom
.calib_info
.saturation_power24
;
2537 saturation_power
= priv
->eeprom
.calib_info
.saturation_power52
;
2539 if (saturation_power
< IWL_TX_POWER_SATURATION_MIN
||
2540 saturation_power
> IWL_TX_POWER_SATURATION_MAX
) {
2542 saturation_power
= IWL_TX_POWER_DEFAULT_SATURATION_24
;
2544 saturation_power
= IWL_TX_POWER_DEFAULT_SATURATION_52
;
2547 /* regulatory txpower limits ... reg_limit values are in half-dBm,
2548 * max_power_avg values are in dBm, convert * 2 */
2550 reg_limit
= ch_info
->fat_max_power_avg
* 2;
2552 reg_limit
= ch_info
->max_power_avg
* 2;
2554 if ((reg_limit
< IWL_TX_POWER_REGULATORY_MIN
) ||
2555 (reg_limit
> IWL_TX_POWER_REGULATORY_MAX
)) {
2557 reg_limit
= IWL_TX_POWER_DEFAULT_REGULATORY_24
;
2559 reg_limit
= IWL_TX_POWER_DEFAULT_REGULATORY_52
;
2562 /* Interpolate txpower calibration values for this channel,
2563 * based on factory calibration tests on spaced channels. */
2564 iwl4965_interpolate_chan(priv
, channel
, &ch_eeprom_info
);
2566 /* calculate tx gain adjustment based on power supply voltage */
2567 voltage
= priv
->eeprom
.calib_info
.voltage
;
2568 init_voltage
= (s32
)le32_to_cpu(priv
->card_alive_init
.voltage
);
2569 voltage_compensation
=
2570 iwl4965_get_voltage_compensation(voltage
, init_voltage
);
2572 IWL_DEBUG_TXPOWER("curr volt %d eeprom volt %d volt comp %d\n",
2574 voltage
, voltage_compensation
);
2576 /* get current temperature (Celsius) */
2577 current_temp
= max(priv
->temperature
, IWL_TX_POWER_TEMPERATURE_MIN
);
2578 current_temp
= min(priv
->temperature
, IWL_TX_POWER_TEMPERATURE_MAX
);
2579 current_temp
= KELVIN_TO_CELSIUS(current_temp
);
2581 /* select thermal txpower adjustment params, based on channel group
2582 * (same frequency group used for mimo txatten adjustment) */
2583 degrees_per_05db_num
=
2584 tx_power_cmp_tble
[txatten_grp
].degrees_per_05db_a
;
2585 degrees_per_05db_denom
=
2586 tx_power_cmp_tble
[txatten_grp
].degrees_per_05db_a_denom
;
2588 /* get per-chain txpower values from factory measurements */
2589 for (c
= 0; c
< 2; c
++) {
2590 measurement
= &ch_eeprom_info
.measurements
[c
][1];
2592 /* txgain adjustment (in half-dB steps) based on difference
2593 * between factory and current temperature */
2594 factory_temp
= measurement
->temperature
;
2595 iwl4965_math_div_round((current_temp
- factory_temp
) *
2596 degrees_per_05db_denom
,
2597 degrees_per_05db_num
,
2598 &temperature_comp
[c
]);
2600 factory_gain_index
[c
] = measurement
->gain_idx
;
2601 factory_actual_pwr
[c
] = measurement
->actual_pow
;
2603 IWL_DEBUG_TXPOWER("chain = %d\n", c
);
2604 IWL_DEBUG_TXPOWER("fctry tmp %d, "
2605 "curr tmp %d, comp %d steps\n",
2606 factory_temp
, current_temp
,
2607 temperature_comp
[c
]);
2609 IWL_DEBUG_TXPOWER("fctry idx %d, fctry pwr %d\n",
2610 factory_gain_index
[c
],
2611 factory_actual_pwr
[c
]);
2614 /* for each of 33 bit-rates (including 1 for CCK) */
2615 for (i
= 0; i
< POWER_TABLE_NUM_ENTRIES
; i
++) {
2617 union iwl4965_tx_power_dual_stream tx_power
;
2619 /* for mimo, reduce each chain's txpower by half
2620 * (3dB, 6 steps), so total output power is regulatory
2623 current_regulatory
= reg_limit
-
2624 IWL_TX_POWER_MIMO_REGULATORY_COMPENSATION
;
2627 current_regulatory
= reg_limit
;
2631 /* find txpower limit, either hardware or regulatory */
2632 power_limit
= saturation_power
- back_off_table
[i
];
2633 if (power_limit
> current_regulatory
)
2634 power_limit
= current_regulatory
;
2636 /* reduce user's txpower request if necessary
2637 * for this rate on this channel */
2638 target_power
= user_target_power
;
2639 if (target_power
> power_limit
)
2640 target_power
= power_limit
;
2642 IWL_DEBUG_TXPOWER("rate %d sat %d reg %d usr %d tgt %d\n",
2643 i
, saturation_power
- back_off_table
[i
],
2644 current_regulatory
, user_target_power
,
2647 /* for each of 2 Tx chains (radio transmitters) */
2648 for (c
= 0; c
< 2; c
++) {
2653 (s32
)le32_to_cpu(priv
->card_alive_init
.
2654 tx_atten
[txatten_grp
][c
]);
2658 /* calculate index; higher index means lower txpower */
2659 power_index
= (u8
) (factory_gain_index
[c
] -
2661 factory_actual_pwr
[c
]) -
2662 temperature_comp
[c
] -
2663 voltage_compensation
+
2666 /* IWL_DEBUG_TXPOWER("calculated txpower index %d\n",
2669 if (power_index
< get_min_power_index(i
, band
))
2670 power_index
= get_min_power_index(i
, band
);
2672 /* adjust 5 GHz index to support negative indexes */
2676 /* CCK, rate 32, reduce txpower for CCK */
2677 if (i
== POWER_TABLE_CCK_ENTRY
)
2679 IWL_TX_POWER_CCK_COMPENSATION_C_STEP
;
2681 /* stay within the table! */
2682 if (power_index
> 107) {
2683 IWL_WARNING("txpower index %d > 107\n",
2687 if (power_index
< 0) {
2688 IWL_WARNING("txpower index %d < 0\n",
2693 /* fill txpower command for this rate/chain */
2694 tx_power
.s
.radio_tx_gain
[c
] =
2695 gain_table
[band
][power_index
].radio
;
2696 tx_power
.s
.dsp_predis_atten
[c
] =
2697 gain_table
[band
][power_index
].dsp
;
2699 IWL_DEBUG_TXPOWER("chain %d mimo %d index %d "
2700 "gain 0x%02x dsp %d\n",
2701 c
, atten_value
, power_index
,
2702 tx_power
.s
.radio_tx_gain
[c
],
2703 tx_power
.s
.dsp_predis_atten
[c
]);
2704 }/* for each chain */
2706 tx_power_tbl
->power_tbl
[i
].dw
= cpu_to_le32(tx_power
.dw
);
2708 }/* for each rate */
2714 * iwl4965_hw_reg_send_txpower - Configure the TXPOWER level user limit
2716 * Uses the active RXON for channel, band, and characteristics (fat, high)
2717 * The power limit is taken from priv->user_txpower_limit.
2719 int iwl4965_hw_reg_send_txpower(struct iwl_priv
*priv
)
2721 struct iwl4965_txpowertable_cmd cmd
= { 0 };
2725 u8 ctrl_chan_high
= 0;
2727 if (test_bit(STATUS_SCANNING
, &priv
->status
)) {
2728 /* If this gets hit a lot, switch it to a BUG() and catch
2729 * the stack trace to find out who is calling this during
2731 IWL_WARNING("TX Power requested while scanning!\n");
2735 band
= priv
->band
== IEEE80211_BAND_2GHZ
;
2737 is_fat
= is_fat_channel(priv
->active_rxon
.flags
);
2740 (priv
->active_rxon
.flags
& RXON_FLG_CTRL_CHANNEL_LOC_HI_MSK
))
2744 cmd
.channel
= priv
->active_rxon
.channel
;
2746 rc
= iwl4965_fill_txpower_tbl(priv
, band
,
2747 le16_to_cpu(priv
->active_rxon
.channel
),
2748 is_fat
, ctrl_chan_high
, &cmd
.tx_power
);
2752 rc
= iwl4965_send_cmd_pdu(priv
, REPLY_TX_PWR_TABLE_CMD
, sizeof(cmd
), &cmd
);
2756 int iwl4965_hw_channel_switch(struct iwl_priv
*priv
, u16 channel
)
2761 u8 ctrl_chan_high
= 0;
2762 struct iwl4965_channel_switch_cmd cmd
= { 0 };
2763 const struct iwl_channel_info
*ch_info
;
2765 band
= priv
->band
== IEEE80211_BAND_2GHZ
;
2767 ch_info
= iwl4965_get_channel_info(priv
, priv
->band
, channel
);
2769 is_fat
= is_fat_channel(priv
->staging_rxon
.flags
);
2772 (priv
->active_rxon
.flags
& RXON_FLG_CTRL_CHANNEL_LOC_HI_MSK
))
2776 cmd
.expect_beacon
= 0;
2777 cmd
.channel
= cpu_to_le16(channel
);
2778 cmd
.rxon_flags
= priv
->active_rxon
.flags
;
2779 cmd
.rxon_filter_flags
= priv
->active_rxon
.filter_flags
;
2780 cmd
.switch_time
= cpu_to_le32(priv
->ucode_beacon_time
);
2782 cmd
.expect_beacon
= is_channel_radar(ch_info
);
2784 cmd
.expect_beacon
= 1;
2786 rc
= iwl4965_fill_txpower_tbl(priv
, band
, channel
, is_fat
,
2787 ctrl_chan_high
, &cmd
.tx_power
);
2789 IWL_DEBUG_11H("error:%d fill txpower_tbl\n", rc
);
2793 rc
= iwl4965_send_cmd_pdu(priv
, REPLY_CHANNEL_SWITCH
, sizeof(cmd
), &cmd
);
2797 #define RTS_HCCA_RETRY_LIMIT 3
2798 #define RTS_DFAULT_RETRY_LIMIT 60
2800 void iwl4965_hw_build_tx_cmd_rate(struct iwl_priv
*priv
,
2801 struct iwl4965_cmd
*cmd
,
2802 struct ieee80211_tx_control
*ctrl
,
2803 struct ieee80211_hdr
*hdr
, int sta_id
,
2806 struct iwl4965_tx_cmd
*tx
= &cmd
->cmd
.tx
;
2807 u8 rts_retry_limit
= 0;
2808 u8 data_retry_limit
= 0;
2809 u16 fc
= le16_to_cpu(hdr
->frame_control
);
2812 int rate_idx
= min(ctrl
->tx_rate
->hw_value
& 0xffff, IWL_RATE_COUNT
- 1);
2814 rate_plcp
= iwl4965_rates
[rate_idx
].plcp
;
2816 rts_retry_limit
= (is_hcca
) ?
2817 RTS_HCCA_RETRY_LIMIT
: RTS_DFAULT_RETRY_LIMIT
;
2819 if ((rate_idx
>= IWL_FIRST_CCK_RATE
) && (rate_idx
<= IWL_LAST_CCK_RATE
))
2820 rate_flags
|= RATE_MCS_CCK_MSK
;
2823 if (ieee80211_is_probe_response(fc
)) {
2824 data_retry_limit
= 3;
2825 if (data_retry_limit
< rts_retry_limit
)
2826 rts_retry_limit
= data_retry_limit
;
2828 data_retry_limit
= IWL_DEFAULT_TX_RETRY
;
2830 if (priv
->data_retry_limit
!= -1)
2831 data_retry_limit
= priv
->data_retry_limit
;
2834 if (ieee80211_is_data(fc
)) {
2835 tx
->initial_rate_index
= 0;
2836 tx
->tx_flags
|= TX_CMD_FLG_STA_RATE_MSK
;
2838 switch (fc
& IEEE80211_FCTL_STYPE
) {
2839 case IEEE80211_STYPE_AUTH
:
2840 case IEEE80211_STYPE_DEAUTH
:
2841 case IEEE80211_STYPE_ASSOC_REQ
:
2842 case IEEE80211_STYPE_REASSOC_REQ
:
2843 if (tx
->tx_flags
& TX_CMD_FLG_RTS_MSK
) {
2844 tx
->tx_flags
&= ~TX_CMD_FLG_RTS_MSK
;
2845 tx
->tx_flags
|= TX_CMD_FLG_CTS_MSK
;
2852 /* Alternate between antenna A and B for successive frames */
2853 if (priv
->use_ant_b_for_management_frame
) {
2854 priv
->use_ant_b_for_management_frame
= 0;
2855 rate_flags
|= RATE_MCS_ANT_B_MSK
;
2857 priv
->use_ant_b_for_management_frame
= 1;
2858 rate_flags
|= RATE_MCS_ANT_A_MSK
;
2862 tx
->rts_retry_limit
= rts_retry_limit
;
2863 tx
->data_retry_limit
= data_retry_limit
;
2864 tx
->rate_n_flags
= iwl4965_hw_set_rate_n_flags(rate_plcp
, rate_flags
);
2867 int iwl4965_hw_get_rx_read(struct iwl_priv
*priv
)
2869 struct iwl4965_shared
*shared_data
= priv
->hw_setting
.shared_virt
;
2871 return IWL_GET_BITS(*shared_data
, rb_closed_stts_rb_num
);
2874 int iwl4965_hw_get_temperature(struct iwl_priv
*priv
)
2876 return priv
->temperature
;
2879 unsigned int iwl4965_hw_get_beacon_cmd(struct iwl_priv
*priv
,
2880 struct iwl4965_frame
*frame
, u8 rate
)
2882 struct iwl4965_tx_beacon_cmd
*tx_beacon_cmd
;
2883 unsigned int frame_size
;
2885 tx_beacon_cmd
= &frame
->u
.beacon
;
2886 memset(tx_beacon_cmd
, 0, sizeof(*tx_beacon_cmd
));
2888 tx_beacon_cmd
->tx
.sta_id
= priv
->hw_setting
.bcast_sta_id
;
2889 tx_beacon_cmd
->tx
.stop_time
.life_time
= TX_CMD_LIFE_TIME_INFINITE
;
2891 frame_size
= iwl4965_fill_beacon_frame(priv
,
2892 tx_beacon_cmd
->frame
,
2893 iwl4965_broadcast_addr
,
2894 sizeof(frame
->u
) - sizeof(*tx_beacon_cmd
));
2896 BUG_ON(frame_size
> MAX_MPDU_SIZE
);
2897 tx_beacon_cmd
->tx
.len
= cpu_to_le16((u16
)frame_size
);
2899 if ((rate
== IWL_RATE_1M_PLCP
) || (rate
>= IWL_RATE_2M_PLCP
))
2900 tx_beacon_cmd
->tx
.rate_n_flags
=
2901 iwl4965_hw_set_rate_n_flags(rate
, RATE_MCS_CCK_MSK
);
2903 tx_beacon_cmd
->tx
.rate_n_flags
=
2904 iwl4965_hw_set_rate_n_flags(rate
, 0);
2906 tx_beacon_cmd
->tx
.tx_flags
= (TX_CMD_FLG_SEQ_CTL_MSK
|
2907 TX_CMD_FLG_TSF_MSK
| TX_CMD_FLG_STA_RATE_MSK
);
2908 return (sizeof(*tx_beacon_cmd
) + frame_size
);
2912 * Tell 4965 where to find circular buffer of Tx Frame Descriptors for
2913 * given Tx queue, and enable the DMA channel used for that queue.
2915 * 4965 supports up to 16 Tx queues in DRAM, mapped to up to 8 Tx DMA
2916 * channels supported in hardware.
2918 int iwl4965_hw_tx_queue_init(struct iwl_priv
*priv
, struct iwl4965_tx_queue
*txq
)
2921 unsigned long flags
;
2922 int txq_id
= txq
->q
.id
;
2924 spin_lock_irqsave(&priv
->lock
, flags
);
2925 rc
= iwl4965_grab_nic_access(priv
);
2927 spin_unlock_irqrestore(&priv
->lock
, flags
);
2931 /* Circular buffer (TFD queue in DRAM) physical base address */
2932 iwl4965_write_direct32(priv
, FH_MEM_CBBC_QUEUE(txq_id
),
2933 txq
->q
.dma_addr
>> 8);
2935 /* Enable DMA channel, using same id as for TFD queue */
2936 iwl4965_write_direct32(
2937 priv
, IWL_FH_TCSR_CHNL_TX_CONFIG_REG(txq_id
),
2938 IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE
|
2939 IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE_VAL
);
2940 iwl4965_release_nic_access(priv
);
2941 spin_unlock_irqrestore(&priv
->lock
, flags
);
2946 int iwl4965_hw_txq_attach_buf_to_tfd(struct iwl_priv
*priv
, void *ptr
,
2947 dma_addr_t addr
, u16 len
)
2950 struct iwl4965_tfd_frame
*tfd
= ptr
;
2951 u32 num_tbs
= IWL_GET_BITS(*tfd
, num_tbs
);
2953 /* Each TFD can point to a maximum 20 Tx buffers */
2954 if ((num_tbs
>= MAX_NUM_OF_TBS
) || (num_tbs
< 0)) {
2955 IWL_ERROR("Error can not send more than %d chunks\n",
2960 index
= num_tbs
/ 2;
2961 is_odd
= num_tbs
& 0x1;
2964 tfd
->pa
[index
].tb1_addr
= cpu_to_le32(addr
);
2965 IWL_SET_BITS(tfd
->pa
[index
], tb1_addr_hi
,
2966 iwl_get_dma_hi_address(addr
));
2967 IWL_SET_BITS(tfd
->pa
[index
], tb1_len
, len
);
2969 IWL_SET_BITS(tfd
->pa
[index
], tb2_addr_lo16
,
2970 (u32
) (addr
& 0xffff));
2971 IWL_SET_BITS(tfd
->pa
[index
], tb2_addr_hi20
, addr
>> 16);
2972 IWL_SET_BITS(tfd
->pa
[index
], tb2_len
, len
);
2975 IWL_SET_BITS(*tfd
, num_tbs
, num_tbs
+ 1);
2980 static void iwl4965_hw_card_show_info(struct iwl_priv
*priv
)
2982 u16 hw_version
= priv
->eeprom
.board_revision_4965
;
2984 IWL_DEBUG_INFO("4965ABGN HW Version %u.%u.%u\n",
2985 ((hw_version
>> 8) & 0x0F),
2986 ((hw_version
>> 8) >> 4), (hw_version
& 0x00FF));
2988 IWL_DEBUG_INFO("4965ABGN PBA Number %.16s\n",
2989 priv
->eeprom
.board_pba_number_4965
);
2992 #define IWL_TX_CRC_SIZE 4
2993 #define IWL_TX_DELIMITER_SIZE 4
2996 * iwl4965_tx_queue_update_wr_ptr - Set up entry in Tx byte-count array
2998 int iwl4965_tx_queue_update_wr_ptr(struct iwl_priv
*priv
,
2999 struct iwl4965_tx_queue
*txq
, u16 byte_cnt
)
3002 int txq_id
= txq
->q
.id
;
3003 struct iwl4965_shared
*shared_data
= priv
->hw_setting
.shared_virt
;
3005 if (txq
->need_update
== 0)
3008 len
= byte_cnt
+ IWL_TX_CRC_SIZE
+ IWL_TX_DELIMITER_SIZE
;
3010 /* Set up byte count within first 256 entries */
3011 IWL_SET_BITS16(shared_data
->queues_byte_cnt_tbls
[txq_id
].
3012 tfd_offset
[txq
->q
.write_ptr
], byte_cnt
, len
);
3014 /* If within first 64 entries, duplicate at end */
3015 if (txq
->q
.write_ptr
< IWL4965_MAX_WIN_SIZE
)
3016 IWL_SET_BITS16(shared_data
->queues_byte_cnt_tbls
[txq_id
].
3017 tfd_offset
[IWL4965_QUEUE_SIZE
+ txq
->q
.write_ptr
],
3024 * iwl4965_set_rxon_chain - Set up Rx chain usage in "staging" RXON image
3026 * Selects how many and which Rx receivers/antennas/chains to use.
3027 * This should not be used for scan command ... it puts data in wrong place.
3029 void iwl4965_set_rxon_chain(struct iwl_priv
*priv
)
3031 u8 is_single
= is_single_stream(priv
);
3032 u8 idle_state
, rx_state
;
3034 priv
->staging_rxon
.rx_chain
= 0;
3035 rx_state
= idle_state
= 3;
3037 /* Tell uCode which antennas are actually connected.
3038 * Before first association, we assume all antennas are connected.
3039 * Just after first association, iwl4965_noise_calibration()
3040 * checks which antennas actually *are* connected. */
3041 priv
->staging_rxon
.rx_chain
|=
3042 cpu_to_le16(priv
->valid_antenna
<< RXON_RX_CHAIN_VALID_POS
);
3044 /* How many receivers should we use? */
3045 iwl4965_get_rx_chain_counter(priv
, &idle_state
, &rx_state
);
3046 priv
->staging_rxon
.rx_chain
|=
3047 cpu_to_le16(rx_state
<< RXON_RX_CHAIN_MIMO_CNT_POS
);
3048 priv
->staging_rxon
.rx_chain
|=
3049 cpu_to_le16(idle_state
<< RXON_RX_CHAIN_CNT_POS
);
3051 if (!is_single
&& (rx_state
>= 2) &&
3052 !test_bit(STATUS_POWER_PMI
, &priv
->status
))
3053 priv
->staging_rxon
.rx_chain
|= RXON_RX_CHAIN_MIMO_FORCE_MSK
;
3055 priv
->staging_rxon
.rx_chain
&= ~RXON_RX_CHAIN_MIMO_FORCE_MSK
;
3057 IWL_DEBUG_ASSOC("rx chain %X\n", priv
->staging_rxon
.rx_chain
);
3061 * sign_extend - Sign extend a value using specified bit as sign-bit
3063 * Example: sign_extend(9, 3) would return -7 as bit3 of 1001b is 1
3064 * and bit0..2 is 001b which when sign extended to 1111111111111001b is -7.
3066 * @param oper value to sign extend
3067 * @param index 0 based bit index (0<=index<32) to sign bit
3069 static s32
sign_extend(u32 oper
, int index
)
3071 u8 shift
= 31 - index
;
3073 return (s32
)(oper
<< shift
) >> shift
;
3077 * iwl4965_get_temperature - return the calibrated temperature (in Kelvin)
3078 * @statistics: Provides the temperature reading from the uCode
3080 * A return of <0 indicates bogus data in the statistics
3082 int iwl4965_get_temperature(const struct iwl_priv
*priv
)
3089 if (test_bit(STATUS_TEMPERATURE
, &priv
->status
) &&
3090 (priv
->statistics
.flag
& STATISTICS_REPLY_FLG_FAT_MODE_MSK
)) {
3091 IWL_DEBUG_TEMP("Running FAT temperature calibration\n");
3092 R1
= (s32
)le32_to_cpu(priv
->card_alive_init
.therm_r1
[1]);
3093 R2
= (s32
)le32_to_cpu(priv
->card_alive_init
.therm_r2
[1]);
3094 R3
= (s32
)le32_to_cpu(priv
->card_alive_init
.therm_r3
[1]);
3095 R4
= le32_to_cpu(priv
->card_alive_init
.therm_r4
[1]);
3097 IWL_DEBUG_TEMP("Running temperature calibration\n");
3098 R1
= (s32
)le32_to_cpu(priv
->card_alive_init
.therm_r1
[0]);
3099 R2
= (s32
)le32_to_cpu(priv
->card_alive_init
.therm_r2
[0]);
3100 R3
= (s32
)le32_to_cpu(priv
->card_alive_init
.therm_r3
[0]);
3101 R4
= le32_to_cpu(priv
->card_alive_init
.therm_r4
[0]);
3105 * Temperature is only 23 bits, so sign extend out to 32.
3107 * NOTE If we haven't received a statistics notification yet
3108 * with an updated temperature, use R4 provided to us in the
3109 * "initialize" ALIVE response.
3111 if (!test_bit(STATUS_TEMPERATURE
, &priv
->status
))
3112 vt
= sign_extend(R4
, 23);
3115 le32_to_cpu(priv
->statistics
.general
.temperature
), 23);
3117 IWL_DEBUG_TEMP("Calib values R[1-3]: %d %d %d R4: %d\n",
3121 IWL_ERROR("Calibration conflict R1 == R3\n");
3125 /* Calculate temperature in degrees Kelvin, adjust by 97%.
3126 * Add offset to center the adjustment around 0 degrees Centigrade. */
3127 temperature
= TEMPERATURE_CALIB_A_VAL
* (vt
- R2
);
3128 temperature
/= (R3
- R1
);
3129 temperature
= (temperature
* 97) / 100 +
3130 TEMPERATURE_CALIB_KELVIN_OFFSET
;
3132 IWL_DEBUG_TEMP("Calibrated temperature: %dK, %dC\n", temperature
,
3133 KELVIN_TO_CELSIUS(temperature
));
3138 /* Adjust Txpower only if temperature variance is greater than threshold. */
3139 #define IWL_TEMPERATURE_THRESHOLD 3
3142 * iwl4965_is_temp_calib_needed - determines if new calibration is needed
3144 * If the temperature changed has changed sufficiently, then a recalibration
3147 * Assumes caller will replace priv->last_temperature once calibration
3150 static int iwl4965_is_temp_calib_needed(struct iwl_priv
*priv
)
3154 if (!test_bit(STATUS_STATISTICS
, &priv
->status
)) {
3155 IWL_DEBUG_TEMP("Temperature not updated -- no statistics.\n");
3159 temp_diff
= priv
->temperature
- priv
->last_temperature
;
3161 /* get absolute value */
3162 if (temp_diff
< 0) {
3163 IWL_DEBUG_POWER("Getting cooler, delta %d, \n", temp_diff
);
3164 temp_diff
= -temp_diff
;
3165 } else if (temp_diff
== 0)
3166 IWL_DEBUG_POWER("Same temp, \n");
3168 IWL_DEBUG_POWER("Getting warmer, delta %d, \n", temp_diff
);
3170 if (temp_diff
< IWL_TEMPERATURE_THRESHOLD
) {
3171 IWL_DEBUG_POWER("Thermal txpower calib not needed\n");
3175 IWL_DEBUG_POWER("Thermal txpower calib needed\n");
3180 /* Calculate noise level, based on measurements during network silence just
3181 * before arriving beacon. This measurement can be done only if we know
3182 * exactly when to expect beacons, therefore only when we're associated. */
3183 static void iwl4965_rx_calc_noise(struct iwl_priv
*priv
)
3185 struct statistics_rx_non_phy
*rx_info
3186 = &(priv
->statistics
.rx
.general
);
3187 int num_active_rx
= 0;
3188 int total_silence
= 0;
3190 le32_to_cpu(rx_info
->beacon_silence_rssi_a
) & IN_BAND_FILTER
;
3192 le32_to_cpu(rx_info
->beacon_silence_rssi_b
) & IN_BAND_FILTER
;
3194 le32_to_cpu(rx_info
->beacon_silence_rssi_c
) & IN_BAND_FILTER
;
3196 if (bcn_silence_a
) {
3197 total_silence
+= bcn_silence_a
;
3200 if (bcn_silence_b
) {
3201 total_silence
+= bcn_silence_b
;
3204 if (bcn_silence_c
) {
3205 total_silence
+= bcn_silence_c
;
3209 /* Average among active antennas */
3211 priv
->last_rx_noise
= (total_silence
/ num_active_rx
) - 107;
3213 priv
->last_rx_noise
= IWL_NOISE_MEAS_NOT_AVAILABLE
;
3215 IWL_DEBUG_CALIB("inband silence a %u, b %u, c %u, dBm %d\n",
3216 bcn_silence_a
, bcn_silence_b
, bcn_silence_c
,
3217 priv
->last_rx_noise
);
3220 void iwl4965_hw_rx_statistics(struct iwl_priv
*priv
, struct iwl4965_rx_mem_buffer
*rxb
)
3222 struct iwl4965_rx_packet
*pkt
= (void *)rxb
->skb
->data
;
3226 IWL_DEBUG_RX("Statistics notification received (%d vs %d).\n",
3227 (int)sizeof(priv
->statistics
), pkt
->len
);
3229 change
= ((priv
->statistics
.general
.temperature
!=
3230 pkt
->u
.stats
.general
.temperature
) ||
3231 ((priv
->statistics
.flag
&
3232 STATISTICS_REPLY_FLG_FAT_MODE_MSK
) !=
3233 (pkt
->u
.stats
.flag
& STATISTICS_REPLY_FLG_FAT_MODE_MSK
)));
3235 memcpy(&priv
->statistics
, &pkt
->u
.stats
, sizeof(priv
->statistics
));
3237 set_bit(STATUS_STATISTICS
, &priv
->status
);
3239 /* Reschedule the statistics timer to occur in
3240 * REG_RECALIB_PERIOD seconds to ensure we get a
3241 * thermal update even if the uCode doesn't give
3243 mod_timer(&priv
->statistics_periodic
, jiffies
+
3244 msecs_to_jiffies(REG_RECALIB_PERIOD
* 1000));
3246 if (unlikely(!test_bit(STATUS_SCANNING
, &priv
->status
)) &&
3247 (pkt
->hdr
.cmd
== STATISTICS_NOTIFICATION
)) {
3248 iwl4965_rx_calc_noise(priv
);
3249 #ifdef CONFIG_IWL4965_SENSITIVITY
3250 queue_work(priv
->workqueue
, &priv
->sensitivity_work
);
3254 /* If the hardware hasn't reported a change in
3255 * temperature then don't bother computing a
3256 * calibrated temperature value */
3260 temp
= iwl4965_get_temperature(priv
);
3264 if (priv
->temperature
!= temp
) {
3265 if (priv
->temperature
)
3266 IWL_DEBUG_TEMP("Temperature changed "
3267 "from %dC to %dC\n",
3268 KELVIN_TO_CELSIUS(priv
->temperature
),
3269 KELVIN_TO_CELSIUS(temp
));
3271 IWL_DEBUG_TEMP("Temperature "
3272 "initialized to %dC\n",
3273 KELVIN_TO_CELSIUS(temp
));
3276 priv
->temperature
= temp
;
3277 set_bit(STATUS_TEMPERATURE
, &priv
->status
);
3279 if (unlikely(!test_bit(STATUS_SCANNING
, &priv
->status
)) &&
3280 iwl4965_is_temp_calib_needed(priv
))
3281 queue_work(priv
->workqueue
, &priv
->txpower_work
);
3284 static void iwl4965_add_radiotap(struct iwl_priv
*priv
,
3285 struct sk_buff
*skb
,
3286 struct iwl4965_rx_phy_res
*rx_start
,
3287 struct ieee80211_rx_status
*stats
,
3290 s8 signal
= stats
->ssi
;
3292 int rate
= stats
->rate_idx
;
3293 u64 tsf
= stats
->mactime
;
3294 __le16 phy_flags_hw
= rx_start
->phy_flags
;
3295 struct iwl4965_rt_rx_hdr
{
3296 struct ieee80211_radiotap_header rt_hdr
;
3297 __le64 rt_tsf
; /* TSF */
3298 u8 rt_flags
; /* radiotap packet flags */
3299 u8 rt_rate
; /* rate in 500kb/s */
3300 __le16 rt_channelMHz
; /* channel in MHz */
3301 __le16 rt_chbitmask
; /* channel bitfield */
3302 s8 rt_dbmsignal
; /* signal in dBm, kluged to signed */
3304 u8 rt_antenna
; /* antenna number */
3305 } __attribute__ ((packed
)) *iwl4965_rt
;
3307 /* TODO: We won't have enough headroom for HT frames. Fix it later. */
3308 if (skb_headroom(skb
) < sizeof(*iwl4965_rt
)) {
3309 if (net_ratelimit())
3310 printk(KERN_ERR
"not enough headroom [%d] for "
3311 "radiotap head [%zd]\n",
3312 skb_headroom(skb
), sizeof(*iwl4965_rt
));
3316 /* put radiotap header in front of 802.11 header and data */
3317 iwl4965_rt
= (void *)skb_push(skb
, sizeof(*iwl4965_rt
));
3319 /* initialise radiotap header */
3320 iwl4965_rt
->rt_hdr
.it_version
= PKTHDR_RADIOTAP_VERSION
;
3321 iwl4965_rt
->rt_hdr
.it_pad
= 0;
3323 /* total header + data */
3324 put_unaligned(cpu_to_le16(sizeof(*iwl4965_rt
)),
3325 &iwl4965_rt
->rt_hdr
.it_len
);
3327 /* Indicate all the fields we add to the radiotap header */
3328 put_unaligned(cpu_to_le32((1 << IEEE80211_RADIOTAP_TSFT
) |
3329 (1 << IEEE80211_RADIOTAP_FLAGS
) |
3330 (1 << IEEE80211_RADIOTAP_RATE
) |
3331 (1 << IEEE80211_RADIOTAP_CHANNEL
) |
3332 (1 << IEEE80211_RADIOTAP_DBM_ANTSIGNAL
) |
3333 (1 << IEEE80211_RADIOTAP_DBM_ANTNOISE
) |
3334 (1 << IEEE80211_RADIOTAP_ANTENNA
)),
3335 &iwl4965_rt
->rt_hdr
.it_present
);
3337 /* Zero the flags, we'll add to them as we go */
3338 iwl4965_rt
->rt_flags
= 0;
3340 put_unaligned(cpu_to_le64(tsf
), &iwl4965_rt
->rt_tsf
);
3342 iwl4965_rt
->rt_dbmsignal
= signal
;
3343 iwl4965_rt
->rt_dbmnoise
= noise
;
3345 /* Convert the channel frequency and set the flags */
3346 put_unaligned(cpu_to_le16(stats
->freq
), &iwl4965_rt
->rt_channelMHz
);
3347 if (!(phy_flags_hw
& RX_RES_PHY_FLAGS_BAND_24_MSK
))
3348 put_unaligned(cpu_to_le16(IEEE80211_CHAN_OFDM
|
3349 IEEE80211_CHAN_5GHZ
),
3350 &iwl4965_rt
->rt_chbitmask
);
3351 else if (phy_flags_hw
& RX_RES_PHY_FLAGS_MOD_CCK_MSK
)
3352 put_unaligned(cpu_to_le16(IEEE80211_CHAN_CCK
|
3353 IEEE80211_CHAN_2GHZ
),
3354 &iwl4965_rt
->rt_chbitmask
);
3356 put_unaligned(cpu_to_le16(IEEE80211_CHAN_OFDM
|
3357 IEEE80211_CHAN_2GHZ
),
3358 &iwl4965_rt
->rt_chbitmask
);
3361 iwl4965_rt
->rt_rate
= 0;
3363 iwl4965_rt
->rt_rate
= iwl4965_rates
[rate
].ieee
;
3368 * It seems that the antenna field in the phy flags value
3369 * is actually a bitfield. This is undefined by radiotap,
3370 * it wants an actual antenna number but I always get "7"
3371 * for most legacy frames I receive indicating that the
3372 * same frame was received on all three RX chains.
3374 * I think this field should be removed in favour of a
3375 * new 802.11n radiotap field "RX chains" that is defined
3378 iwl4965_rt
->rt_antenna
=
3379 le16_to_cpu(phy_flags_hw
& RX_RES_PHY_FLAGS_ANTENNA_MSK
) >> 4;
3381 /* set the preamble flag if appropriate */
3382 if (phy_flags_hw
& RX_RES_PHY_FLAGS_SHORT_PREAMBLE_MSK
)
3383 iwl4965_rt
->rt_flags
|= IEEE80211_RADIOTAP_F_SHORTPRE
;
3385 stats
->flag
|= RX_FLAG_RADIOTAP
;
3388 static void iwl_update_rx_stats(struct iwl_priv
*priv
, u16 fc
, u16 len
)
3390 /* 0 - mgmt, 1 - cnt, 2 - data */
3391 int idx
= (fc
& IEEE80211_FCTL_FTYPE
) >> 2;
3392 priv
->rx_stats
[idx
].cnt
++;
3393 priv
->rx_stats
[idx
].bytes
+= len
;
3396 static u32
iwl4965_translate_rx_status(u32 decrypt_in
)
3398 u32 decrypt_out
= 0;
3400 if ((decrypt_in
& RX_RES_STATUS_STATION_FOUND
) ==
3401 RX_RES_STATUS_STATION_FOUND
)
3402 decrypt_out
|= (RX_RES_STATUS_STATION_FOUND
|
3403 RX_RES_STATUS_NO_STATION_INFO_MISMATCH
);
3405 decrypt_out
|= (decrypt_in
& RX_RES_STATUS_SEC_TYPE_MSK
);
3407 /* packet was not encrypted */
3408 if ((decrypt_in
& RX_RES_STATUS_SEC_TYPE_MSK
) ==
3409 RX_RES_STATUS_SEC_TYPE_NONE
)
3412 /* packet was encrypted with unknown alg */
3413 if ((decrypt_in
& RX_RES_STATUS_SEC_TYPE_MSK
) ==
3414 RX_RES_STATUS_SEC_TYPE_ERR
)
3417 /* decryption was not done in HW */
3418 if ((decrypt_in
& RX_MPDU_RES_STATUS_DEC_DONE_MSK
) !=
3419 RX_MPDU_RES_STATUS_DEC_DONE_MSK
)
3422 switch (decrypt_in
& RX_RES_STATUS_SEC_TYPE_MSK
) {
3424 case RX_RES_STATUS_SEC_TYPE_CCMP
:
3425 /* alg is CCM: check MIC only */
3426 if (!(decrypt_in
& RX_MPDU_RES_STATUS_MIC_OK
))
3428 decrypt_out
|= RX_RES_STATUS_BAD_ICV_MIC
;
3430 decrypt_out
|= RX_RES_STATUS_DECRYPT_OK
;
3434 case RX_RES_STATUS_SEC_TYPE_TKIP
:
3435 if (!(decrypt_in
& RX_MPDU_RES_STATUS_TTAK_OK
)) {
3437 decrypt_out
|= RX_RES_STATUS_BAD_KEY_TTAK
;
3440 /* fall through if TTAK OK */
3442 if (!(decrypt_in
& RX_MPDU_RES_STATUS_ICV_OK
))
3443 decrypt_out
|= RX_RES_STATUS_BAD_ICV_MIC
;
3445 decrypt_out
|= RX_RES_STATUS_DECRYPT_OK
;
3449 IWL_DEBUG_RX("decrypt_in:0x%x decrypt_out = 0x%x\n",
3450 decrypt_in
, decrypt_out
);
3455 static void iwl4965_handle_data_packet(struct iwl_priv
*priv
, int is_data
,
3457 struct iwl4965_rx_mem_buffer
*rxb
,
3458 struct ieee80211_rx_status
*stats
)
3460 struct iwl4965_rx_packet
*pkt
= (struct iwl4965_rx_packet
*)rxb
->skb
->data
;
3461 struct iwl4965_rx_phy_res
*rx_start
= (include_phy
) ?
3462 (struct iwl4965_rx_phy_res
*)&(pkt
->u
.raw
[0]) : NULL
;
3463 struct ieee80211_hdr
*hdr
;
3466 unsigned int skblen
;
3468 u32 ampdu_status_legacy
;
3470 if (!include_phy
&& priv
->last_phy_res
[0])
3471 rx_start
= (struct iwl4965_rx_phy_res
*)&priv
->last_phy_res
[1];
3474 IWL_ERROR("MPDU frame without a PHY data\n");
3478 hdr
= (struct ieee80211_hdr
*)((u8
*) & rx_start
[1] +
3479 rx_start
->cfg_phy_cnt
);
3481 len
= le16_to_cpu(rx_start
->byte_count
);
3483 rx_end
= (__le32
*) ((u8
*) & pkt
->u
.raw
[0] +
3484 sizeof(struct iwl4965_rx_phy_res
) +
3485 rx_start
->cfg_phy_cnt
+ len
);
3488 struct iwl4965_rx_mpdu_res_start
*amsdu
=
3489 (struct iwl4965_rx_mpdu_res_start
*)pkt
->u
.raw
;
3491 hdr
= (struct ieee80211_hdr
*)(pkt
->u
.raw
+
3492 sizeof(struct iwl4965_rx_mpdu_res_start
));
3493 len
= le16_to_cpu(amsdu
->byte_count
);
3494 rx_start
->byte_count
= amsdu
->byte_count
;
3495 rx_end
= (__le32
*) (((u8
*) hdr
) + len
);
3497 if (len
> priv
->hw_setting
.max_pkt_size
|| len
< 16) {
3498 IWL_WARNING("byte count out of range [16,4K] : %d\n", len
);
3502 ampdu_status
= le32_to_cpu(*rx_end
);
3503 skblen
= ((u8
*) rx_end
- (u8
*) & pkt
->u
.raw
[0]) + sizeof(u32
);
3506 /* New status scheme, need to translate */
3507 ampdu_status_legacy
= ampdu_status
;
3508 ampdu_status
= iwl4965_translate_rx_status(ampdu_status
);
3511 /* start from MAC */
3512 skb_reserve(rxb
->skb
, (void *)hdr
- (void *)pkt
);
3513 skb_put(rxb
->skb
, len
); /* end where data ends */
3515 /* We only process data packets if the interface is open */
3516 if (unlikely(!priv
->is_open
)) {
3517 IWL_DEBUG_DROP_LIMIT
3518 ("Dropping packet while interface is not open.\n");
3523 hdr
= (struct ieee80211_hdr
*)rxb
->skb
->data
;
3525 if (iwl4965_mod_params
.hw_crypto
)
3526 iwl4965_set_decrypted_flag(priv
, rxb
->skb
, ampdu_status
, stats
);
3528 if (priv
->add_radiotap
)
3529 iwl4965_add_radiotap(priv
, rxb
->skb
, rx_start
, stats
, ampdu_status
);
3531 iwl_update_rx_stats(priv
, le16_to_cpu(hdr
->frame_control
), len
);
3532 ieee80211_rx_irqsafe(priv
->hw
, rxb
->skb
, stats
);
3533 priv
->alloc_rxb_skb
--;
3536 priv
->led_packets
+= len
;
3537 iwl4965_setup_activity_timer(priv
);
3541 /* Calc max signal level (dBm) among 3 possible receivers */
3542 static int iwl4965_calc_rssi(struct iwl4965_rx_phy_res
*rx_resp
)
3544 /* data from PHY/DSP regarding signal strength, etc.,
3545 * contents are always there, not configurable by host. */
3546 struct iwl4965_rx_non_cfg_phy
*ncphy
=
3547 (struct iwl4965_rx_non_cfg_phy
*)rx_resp
->non_cfg_phy
;
3548 u32 agc
= (le16_to_cpu(ncphy
->agc_info
) & IWL_AGC_DB_MASK
)
3551 u32 valid_antennae
=
3552 (le16_to_cpu(rx_resp
->phy_flags
) & RX_PHY_FLAGS_ANTENNAE_MASK
)
3553 >> RX_PHY_FLAGS_ANTENNAE_OFFSET
;
3557 /* Find max rssi among 3 possible receivers.
3558 * These values are measured by the digital signal processor (DSP).
3559 * They should stay fairly constant even as the signal strength varies,
3560 * if the radio's automatic gain control (AGC) is working right.
3561 * AGC value (see below) will provide the "interesting" info. */
3562 for (i
= 0; i
< 3; i
++)
3563 if (valid_antennae
& (1 << i
))
3564 max_rssi
= max(ncphy
->rssi_info
[i
<< 1], max_rssi
);
3566 IWL_DEBUG_STATS("Rssi In A %d B %d C %d Max %d AGC dB %d\n",
3567 ncphy
->rssi_info
[0], ncphy
->rssi_info
[2], ncphy
->rssi_info
[4],
3570 /* dBm = max_rssi dB - agc dB - constant.
3571 * Higher AGC (higher radio gain) means lower signal. */
3572 return (max_rssi
- agc
- IWL_RSSI_OFFSET
);
3575 #ifdef CONFIG_IWL4965_HT
3577 /* Parsed Information Elements */
3578 struct ieee802_11_elems
{
3588 u8 ht_cap_param_len
;
3590 u8 ht_extra_param_len
;
3593 static int parse_elems(u8
*start
, size_t len
, struct ieee802_11_elems
*elems
)
3599 memset(elems
, 0, sizeof(*elems
));
3612 case WLAN_EID_DS_PARAMS
:
3613 elems
->ds_params
= pos
;
3614 elems
->ds_params_len
= elen
;
3618 elems
->tim_len
= elen
;
3620 case WLAN_EID_IBSS_PARAMS
:
3621 elems
->ibss_params
= pos
;
3622 elems
->ibss_params_len
= elen
;
3624 case WLAN_EID_ERP_INFO
:
3625 elems
->erp_info
= pos
;
3626 elems
->erp_info_len
= elen
;
3628 case WLAN_EID_HT_CAPABILITY
:
3629 elems
->ht_cap_param
= pos
;
3630 elems
->ht_cap_param_len
= elen
;
3632 case WLAN_EID_HT_EXTRA_INFO
:
3633 elems
->ht_extra_param
= pos
;
3634 elems
->ht_extra_param_len
= elen
;
3648 void iwl4965_init_ht_hw_capab(struct ieee80211_ht_info
*ht_info
,
3649 enum ieee80211_band band
)
3652 memset(ht_info
->supp_mcs_set
, 0, 16);
3654 ht_info
->ht_supported
= 1;
3656 if (band
== IEEE80211_BAND_5GHZ
) {
3657 ht_info
->cap
|= (u16
)IEEE80211_HT_CAP_SUP_WIDTH
;
3658 ht_info
->cap
|= (u16
)IEEE80211_HT_CAP_SGI_40
;
3659 ht_info
->supp_mcs_set
[4] = 0x01;
3661 ht_info
->cap
|= (u16
)IEEE80211_HT_CAP_GRN_FLD
;
3662 ht_info
->cap
|= (u16
)IEEE80211_HT_CAP_SGI_20
;
3663 ht_info
->cap
|= (u16
)(IEEE80211_HT_CAP_MIMO_PS
&
3664 (IWL_MIMO_PS_NONE
<< 2));
3665 if (iwl4965_mod_params
.amsdu_size_8K
) {
3666 printk(KERN_DEBUG
"iwl4965 in A-MSDU 8K support mode\n");
3667 ht_info
->cap
|= (u16
)IEEE80211_HT_CAP_MAX_AMSDU
;
3670 ht_info
->ampdu_factor
= CFG_HT_RX_AMPDU_FACTOR_DEF
;
3671 ht_info
->ampdu_density
= CFG_HT_MPDU_DENSITY_DEF
;
3673 ht_info
->supp_mcs_set
[0] = 0xFF;
3674 ht_info
->supp_mcs_set
[1] = 0xFF;
3676 #endif /* CONFIG_IWL4965_HT */
3678 static void iwl4965_sta_modify_ps_wake(struct iwl_priv
*priv
, int sta_id
)
3680 unsigned long flags
;
3682 spin_lock_irqsave(&priv
->sta_lock
, flags
);
3683 priv
->stations
[sta_id
].sta
.station_flags
&= ~STA_FLG_PWR_SAVE_MSK
;
3684 priv
->stations
[sta_id
].sta
.station_flags_msk
= STA_FLG_PWR_SAVE_MSK
;
3685 priv
->stations
[sta_id
].sta
.sta
.modify_mask
= 0;
3686 priv
->stations
[sta_id
].sta
.mode
= STA_CONTROL_MODIFY_MSK
;
3687 spin_unlock_irqrestore(&priv
->sta_lock
, flags
);
3689 iwl4965_send_add_station(priv
, &priv
->stations
[sta_id
].sta
, CMD_ASYNC
);
3692 static void iwl4965_update_ps_mode(struct iwl_priv
*priv
, u16 ps_bit
, u8
*addr
)
3694 /* FIXME: need locking over ps_status ??? */
3695 u8 sta_id
= iwl4965_hw_find_station(priv
, addr
);
3697 if (sta_id
!= IWL_INVALID_STATION
) {
3698 u8 sta_awake
= priv
->stations
[sta_id
].
3699 ps_status
== STA_PS_STATUS_WAKE
;
3701 if (sta_awake
&& ps_bit
)
3702 priv
->stations
[sta_id
].ps_status
= STA_PS_STATUS_SLEEP
;
3703 else if (!sta_awake
&& !ps_bit
) {
3704 iwl4965_sta_modify_ps_wake(priv
, sta_id
);
3705 priv
->stations
[sta_id
].ps_status
= STA_PS_STATUS_WAKE
;
3709 #ifdef CONFIG_IWLWIFI_DEBUG
3712 * iwl4965_dbg_report_frame - dump frame to syslog during debug sessions
3714 * You may hack this function to show different aspects of received frames,
3715 * including selective frame dumps.
3716 * group100 parameter selects whether to show 1 out of 100 good frames.
3718 * TODO: This was originally written for 3945, need to audit for
3719 * proper operation with 4965.
3721 static void iwl4965_dbg_report_frame(struct iwl_priv
*priv
,
3722 struct iwl4965_rx_packet
*pkt
,
3723 struct ieee80211_hdr
*header
, int group100
)
3726 u32 print_summary
= 0;
3727 u32 print_dump
= 0; /* set to 1 to dump all frames' contents */
3744 struct iwl4965_rx_frame_stats
*rx_stats
= IWL_RX_STATS(pkt
);
3745 struct iwl4965_rx_frame_hdr
*rx_hdr
= IWL_RX_HDR(pkt
);
3746 struct iwl4965_rx_frame_end
*rx_end
= IWL_RX_END(pkt
);
3747 u8
*data
= IWL_RX_DATA(pkt
);
3749 if (likely(!(iwl_debug_level
& IWL_DL_RX
)))
3753 fc
= le16_to_cpu(header
->frame_control
);
3754 seq_ctl
= le16_to_cpu(header
->seq_ctrl
);
3757 channel
= le16_to_cpu(rx_hdr
->channel
);
3758 phy_flags
= le16_to_cpu(rx_hdr
->phy_flags
);
3759 rate_sym
= rx_hdr
->rate
;
3760 length
= le16_to_cpu(rx_hdr
->len
);
3762 /* end-of-frame status and timestamp */
3763 status
= le32_to_cpu(rx_end
->status
);
3764 bcn_tmr
= le32_to_cpu(rx_end
->beacon_timestamp
);
3765 tsf_low
= le64_to_cpu(rx_end
->timestamp
) & 0x0ffffffff;
3766 tsf
= le64_to_cpu(rx_end
->timestamp
);
3768 /* signal statistics */
3769 rssi
= rx_stats
->rssi
;
3770 agc
= rx_stats
->agc
;
3771 sig_avg
= le16_to_cpu(rx_stats
->sig_avg
);
3772 noise_diff
= le16_to_cpu(rx_stats
->noise_diff
);
3774 to_us
= !compare_ether_addr(header
->addr1
, priv
->mac_addr
);
3776 /* if data frame is to us and all is good,
3777 * (optionally) print summary for only 1 out of every 100 */
3778 if (to_us
&& (fc
& ~IEEE80211_FCTL_PROTECTED
) ==
3779 (IEEE80211_FCTL_FROMDS
| IEEE80211_FTYPE_DATA
)) {
3782 print_summary
= 1; /* print each frame */
3783 else if (priv
->framecnt_to_us
< 100) {
3784 priv
->framecnt_to_us
++;
3787 priv
->framecnt_to_us
= 0;
3792 /* print summary for all other frames */
3796 if (print_summary
) {
3802 title
= "100Frames";
3803 else if (fc
& IEEE80211_FCTL_RETRY
)
3805 else if (ieee80211_is_assoc_response(fc
))
3807 else if (ieee80211_is_reassoc_response(fc
))
3809 else if (ieee80211_is_probe_response(fc
)) {
3811 print_dump
= 1; /* dump frame contents */
3812 } else if (ieee80211_is_beacon(fc
)) {
3814 print_dump
= 1; /* dump frame contents */
3815 } else if (ieee80211_is_atim(fc
))
3817 else if (ieee80211_is_auth(fc
))
3819 else if (ieee80211_is_deauth(fc
))
3821 else if (ieee80211_is_disassoc(fc
))
3826 rate_idx
= iwl4965_hwrate_to_plcp_idx(rate_sym
);
3827 if (unlikely(rate_idx
== -1))
3830 bitrate
= iwl4965_rates
[rate_idx
].ieee
/ 2;
3832 /* print frame summary.
3833 * MAC addresses show just the last byte (for brevity),
3834 * but you can hack it to show more, if you'd like to. */
3836 IWL_DEBUG_RX("%s: mhd=0x%04x, dst=0x%02x, "
3837 "len=%u, rssi=%d, chnl=%d, rate=%u, \n",
3838 title
, fc
, header
->addr1
[5],
3839 length
, rssi
, channel
, bitrate
);
3841 /* src/dst addresses assume managed mode */
3842 IWL_DEBUG_RX("%s: 0x%04x, dst=0x%02x, "
3843 "src=0x%02x, rssi=%u, tim=%lu usec, "
3844 "phy=0x%02x, chnl=%d\n",
3845 title
, fc
, header
->addr1
[5],
3846 header
->addr3
[5], rssi
,
3847 tsf_low
- priv
->scan_start_tsf
,
3848 phy_flags
, channel
);
3852 iwl_print_hex_dump(IWL_DL_RX
, data
, length
);
3855 static inline void iwl4965_dbg_report_frame(struct iwl_priv
*priv
,
3856 struct iwl4965_rx_packet
*pkt
,
3857 struct ieee80211_hdr
*header
,
3864 #define IWL_DELAY_NEXT_SCAN_AFTER_ASSOC (HZ*6)
3866 /* Called for REPLY_4965_RX (legacy ABG frames), or
3867 * REPLY_RX_MPDU_CMD (HT high-throughput N frames). */
3868 static void iwl4965_rx_reply_rx(struct iwl_priv
*priv
,
3869 struct iwl4965_rx_mem_buffer
*rxb
)
3871 struct ieee80211_hdr
*header
;
3872 struct ieee80211_rx_status rx_status
;
3873 struct iwl4965_rx_packet
*pkt
= (void *)rxb
->skb
->data
;
3874 /* Use phy data (Rx signal strength, etc.) contained within
3875 * this rx packet for legacy frames,
3876 * or phy data cached from REPLY_RX_PHY_CMD for HT frames. */
3877 int include_phy
= (pkt
->hdr
.cmd
== REPLY_4965_RX
);
3878 struct iwl4965_rx_phy_res
*rx_start
= (include_phy
) ?
3879 (struct iwl4965_rx_phy_res
*)&(pkt
->u
.raw
[0]) :
3880 (struct iwl4965_rx_phy_res
*)&priv
->last_phy_res
[1];
3882 unsigned int len
= 0;
3886 rx_status
.mactime
= le64_to_cpu(rx_start
->timestamp
);
3887 rx_status
.freq
= ieee80211chan2mhz(le16_to_cpu(rx_start
->channel
));
3888 rx_status
.band
= (rx_start
->phy_flags
& RX_RES_PHY_FLAGS_BAND_24_MSK
) ?
3889 IEEE80211_BAND_2GHZ
: IEEE80211_BAND_5GHZ
;
3890 rx_status
.rate_idx
= iwl4965_hwrate_to_plcp_idx(
3891 le32_to_cpu(rx_start
->rate_n_flags
));
3893 if (rx_status
.band
== IEEE80211_BAND_5GHZ
)
3894 rx_status
.rate_idx
-= IWL_FIRST_OFDM_RATE
;
3896 rx_status
.antenna
= 0;
3899 if ((unlikely(rx_start
->cfg_phy_cnt
> 20))) {
3901 ("dsp size out of range [0,20]: "
3902 "%d/n", rx_start
->cfg_phy_cnt
);
3907 if (priv
->last_phy_res
[0])
3908 rx_start
= (struct iwl4965_rx_phy_res
*)
3909 &priv
->last_phy_res
[1];
3915 IWL_ERROR("MPDU frame without a PHY data\n");
3920 header
= (struct ieee80211_hdr
*)((u8
*) & rx_start
[1]
3921 + rx_start
->cfg_phy_cnt
);
3923 len
= le16_to_cpu(rx_start
->byte_count
);
3924 rx_end
= (__le32
*)(pkt
->u
.raw
+ rx_start
->cfg_phy_cnt
+
3925 sizeof(struct iwl4965_rx_phy_res
) + len
);
3927 struct iwl4965_rx_mpdu_res_start
*amsdu
=
3928 (struct iwl4965_rx_mpdu_res_start
*)pkt
->u
.raw
;
3930 header
= (void *)(pkt
->u
.raw
+
3931 sizeof(struct iwl4965_rx_mpdu_res_start
));
3932 len
= le16_to_cpu(amsdu
->byte_count
);
3933 rx_end
= (__le32
*) (pkt
->u
.raw
+
3934 sizeof(struct iwl4965_rx_mpdu_res_start
) + len
);
3937 if (!(*rx_end
& RX_RES_STATUS_NO_CRC32_ERROR
) ||
3938 !(*rx_end
& RX_RES_STATUS_NO_RXE_OVERFLOW
)) {
3939 IWL_DEBUG_RX("Bad CRC or FIFO: 0x%08X.\n",
3940 le32_to_cpu(*rx_end
));
3944 priv
->ucode_beacon_time
= le32_to_cpu(rx_start
->beacon_time_stamp
);
3946 /* Find max signal strength (dBm) among 3 antenna/receiver chains */
3947 rx_status
.ssi
= iwl4965_calc_rssi(rx_start
);
3949 /* Meaningful noise values are available only from beacon statistics,
3950 * which are gathered only when associated, and indicate noise
3951 * only for the associated network channel ...
3952 * Ignore these noise values while scanning (other channels) */
3953 if (iwl4965_is_associated(priv
) &&
3954 !test_bit(STATUS_SCANNING
, &priv
->status
)) {
3955 rx_status
.noise
= priv
->last_rx_noise
;
3956 rx_status
.signal
= iwl4965_calc_sig_qual(rx_status
.ssi
,
3959 rx_status
.noise
= IWL_NOISE_MEAS_NOT_AVAILABLE
;
3960 rx_status
.signal
= iwl4965_calc_sig_qual(rx_status
.ssi
, 0);
3963 /* Reset beacon noise level if not associated. */
3964 if (!iwl4965_is_associated(priv
))
3965 priv
->last_rx_noise
= IWL_NOISE_MEAS_NOT_AVAILABLE
;
3967 /* Set "1" to report good data frames in groups of 100 */
3968 /* FIXME: need to optimze the call: */
3969 iwl4965_dbg_report_frame(priv
, pkt
, header
, 1);
3971 IWL_DEBUG_STATS_LIMIT("Rssi %d, noise %d, qual %d, TSF %llu\n",
3972 rx_status
.ssi
, rx_status
.noise
, rx_status
.signal
,
3975 network_packet
= iwl4965_is_network_packet(priv
, header
);
3976 if (network_packet
) {
3977 priv
->last_rx_rssi
= rx_status
.ssi
;
3978 priv
->last_beacon_time
= priv
->ucode_beacon_time
;
3979 priv
->last_tsf
= le64_to_cpu(rx_start
->timestamp
);
3982 fc
= le16_to_cpu(header
->frame_control
);
3983 switch (fc
& IEEE80211_FCTL_FTYPE
) {
3984 case IEEE80211_FTYPE_MGMT
:
3986 if (priv
->iw_mode
== IEEE80211_IF_TYPE_AP
)
3987 iwl4965_update_ps_mode(priv
, fc
& IEEE80211_FCTL_PM
,
3989 switch (fc
& IEEE80211_FCTL_STYPE
) {
3990 case IEEE80211_STYPE_PROBE_RESP
:
3991 case IEEE80211_STYPE_BEACON
:
3992 if ((priv
->iw_mode
== IEEE80211_IF_TYPE_STA
&&
3993 !compare_ether_addr(header
->addr2
, priv
->bssid
)) ||
3994 (priv
->iw_mode
== IEEE80211_IF_TYPE_IBSS
&&
3995 !compare_ether_addr(header
->addr3
, priv
->bssid
))) {
3996 struct ieee80211_mgmt
*mgmt
=
3997 (struct ieee80211_mgmt
*)header
;
3999 le64_to_cpu(mgmt
->u
.beacon
.timestamp
);
4001 priv
->timestamp0
= timestamp
& 0xFFFFFFFF;
4003 (timestamp
>> 32) & 0xFFFFFFFF;
4004 priv
->beacon_int
= le16_to_cpu(
4005 mgmt
->u
.beacon
.beacon_int
);
4006 if (priv
->call_post_assoc_from_beacon
&&
4007 (priv
->iw_mode
== IEEE80211_IF_TYPE_STA
)) {
4008 priv
->call_post_assoc_from_beacon
= 0;
4009 queue_work(priv
->workqueue
,
4010 &priv
->post_associate
.work
);
4015 case IEEE80211_STYPE_ACTION
:
4019 * TODO: Use the new callback function from
4020 * mac80211 instead of sniffing these packets.
4022 case IEEE80211_STYPE_ASSOC_RESP
:
4023 case IEEE80211_STYPE_REASSOC_RESP
:
4024 if (network_packet
) {
4025 #ifdef CONFIG_IWL4965_HT
4027 struct ieee802_11_elems elems
;
4028 #endif /*CONFIG_IWL4965_HT */
4029 struct ieee80211_mgmt
*mgnt
=
4030 (struct ieee80211_mgmt
*)header
;
4032 /* We have just associated, give some
4033 * time for the 4-way handshake if
4034 * any. Don't start scan too early. */
4035 priv
->next_scan_jiffies
= jiffies
+
4036 IWL_DELAY_NEXT_SCAN_AFTER_ASSOC
;
4038 priv
->assoc_id
= (~((1 << 15) | (1 << 14))
4039 & le16_to_cpu(mgnt
->u
.assoc_resp
.aid
));
4040 priv
->assoc_capability
=
4042 mgnt
->u
.assoc_resp
.capab_info
);
4043 #ifdef CONFIG_IWL4965_HT
4044 pos
= mgnt
->u
.assoc_resp
.variable
;
4045 if (!parse_elems(pos
,
4046 len
- (pos
- (u8
*) mgnt
),
4048 if (elems
.ht_extra_param
&&
4052 #endif /*CONFIG_IWL4965_HT */
4053 /* assoc_id is 0 no association */
4054 if (!priv
->assoc_id
)
4056 if (priv
->beacon_int
)
4057 queue_work(priv
->workqueue
,
4058 &priv
->post_associate
.work
);
4060 priv
->call_post_assoc_from_beacon
= 1;
4065 case IEEE80211_STYPE_PROBE_REQ
:
4066 if ((priv
->iw_mode
== IEEE80211_IF_TYPE_IBSS
) &&
4067 !iwl4965_is_associated(priv
)) {
4068 DECLARE_MAC_BUF(mac1
);
4069 DECLARE_MAC_BUF(mac2
);
4070 DECLARE_MAC_BUF(mac3
);
4072 IWL_DEBUG_DROP("Dropping (non network): "
4074 print_mac(mac1
, header
->addr1
),
4075 print_mac(mac2
, header
->addr2
),
4076 print_mac(mac3
, header
->addr3
));
4080 iwl4965_handle_data_packet(priv
, 0, include_phy
, rxb
, &rx_status
);
4083 case IEEE80211_FTYPE_CTL
:
4084 #ifdef CONFIG_IWL4965_HT
4085 switch (fc
& IEEE80211_FCTL_STYPE
) {
4086 case IEEE80211_STYPE_BACK_REQ
:
4087 IWL_DEBUG_HT("IEEE80211_STYPE_BACK_REQ arrived\n");
4088 iwl4965_handle_data_packet(priv
, 0, include_phy
,
4097 case IEEE80211_FTYPE_DATA
: {
4098 DECLARE_MAC_BUF(mac1
);
4099 DECLARE_MAC_BUF(mac2
);
4100 DECLARE_MAC_BUF(mac3
);
4102 if (priv
->iw_mode
== IEEE80211_IF_TYPE_AP
)
4103 iwl4965_update_ps_mode(priv
, fc
& IEEE80211_FCTL_PM
,
4106 if (unlikely(!network_packet
))
4107 IWL_DEBUG_DROP("Dropping (non network): "
4109 print_mac(mac1
, header
->addr1
),
4110 print_mac(mac2
, header
->addr2
),
4111 print_mac(mac3
, header
->addr3
));
4112 else if (unlikely(iwl4965_is_duplicate_packet(priv
, header
)))
4113 IWL_DEBUG_DROP("Dropping (dup): %s, %s, %s\n",
4114 print_mac(mac1
, header
->addr1
),
4115 print_mac(mac2
, header
->addr2
),
4116 print_mac(mac3
, header
->addr3
));
4118 iwl4965_handle_data_packet(priv
, 1, include_phy
, rxb
,
4128 /* Cache phy data (Rx signal strength, etc) for HT frame (REPLY_RX_PHY_CMD).
4129 * This will be used later in iwl4965_rx_reply_rx() for REPLY_RX_MPDU_CMD. */
4130 static void iwl4965_rx_reply_rx_phy(struct iwl_priv
*priv
,
4131 struct iwl4965_rx_mem_buffer
*rxb
)
4133 struct iwl4965_rx_packet
*pkt
= (void *)rxb
->skb
->data
;
4134 priv
->last_phy_res
[0] = 1;
4135 memcpy(&priv
->last_phy_res
[1], &(pkt
->u
.raw
[0]),
4136 sizeof(struct iwl4965_rx_phy_res
));
4139 static void iwl4965_rx_missed_beacon_notif(struct iwl_priv
*priv
,
4140 struct iwl4965_rx_mem_buffer
*rxb
)
4143 #ifdef CONFIG_IWL4965_SENSITIVITY
4144 struct iwl4965_rx_packet
*pkt
= (void *)rxb
->skb
->data
;
4145 struct iwl4965_missed_beacon_notif
*missed_beacon
;
4147 missed_beacon
= &pkt
->u
.missed_beacon
;
4148 if (le32_to_cpu(missed_beacon
->consequtive_missed_beacons
) > 5) {
4149 IWL_DEBUG_CALIB("missed bcn cnsq %d totl %d rcd %d expctd %d\n",
4150 le32_to_cpu(missed_beacon
->consequtive_missed_beacons
),
4151 le32_to_cpu(missed_beacon
->total_missed_becons
),
4152 le32_to_cpu(missed_beacon
->num_recvd_beacons
),
4153 le32_to_cpu(missed_beacon
->num_expected_beacons
));
4154 priv
->sensitivity_data
.state
= IWL_SENS_CALIB_NEED_REINIT
;
4155 if (unlikely(!test_bit(STATUS_SCANNING
, &priv
->status
)))
4156 queue_work(priv
->workqueue
, &priv
->sensitivity_work
);
4158 #endif /*CONFIG_IWL4965_SENSITIVITY*/
4161 #ifdef CONFIG_IWL4965_HT
4164 * iwl4965_sta_modify_enable_tid_tx - Enable Tx for this TID in station table
4166 static void iwl4965_sta_modify_enable_tid_tx(struct iwl_priv
*priv
,
4167 int sta_id
, int tid
)
4169 unsigned long flags
;
4171 /* Remove "disable" flag, to enable Tx for this TID */
4172 spin_lock_irqsave(&priv
->sta_lock
, flags
);
4173 priv
->stations
[sta_id
].sta
.sta
.modify_mask
= STA_MODIFY_TID_DISABLE_TX
;
4174 priv
->stations
[sta_id
].sta
.tid_disable_tx
&= cpu_to_le16(~(1 << tid
));
4175 priv
->stations
[sta_id
].sta
.mode
= STA_CONTROL_MODIFY_MSK
;
4176 spin_unlock_irqrestore(&priv
->sta_lock
, flags
);
4178 iwl4965_send_add_station(priv
, &priv
->stations
[sta_id
].sta
, CMD_ASYNC
);
4182 * iwl4965_tx_status_reply_compressed_ba - Update tx status from block-ack
4184 * Go through block-ack's bitmap of ACK'd frames, update driver's record of
4185 * ACK vs. not. This gets sent to mac80211, then to rate scaling algo.
4187 static int iwl4965_tx_status_reply_compressed_ba(struct iwl_priv
*priv
,
4188 struct iwl4965_ht_agg
*agg
,
4189 struct iwl4965_compressed_ba_resp
*
4194 u16 seq_ctl
= le16_to_cpu(ba_resp
->seq_ctl
);
4195 u16 scd_flow
= le16_to_cpu(ba_resp
->scd_flow
);
4198 struct ieee80211_tx_status
*tx_status
;
4200 if (unlikely(!agg
->wait_for_ba
)) {
4201 IWL_ERROR("Received BA when not expected\n");
4205 /* Mark that the expected block-ack response arrived */
4206 agg
->wait_for_ba
= 0;
4207 IWL_DEBUG_TX_REPLY("BA %d %d\n", agg
->start_idx
, ba_resp
->seq_ctl
);
4209 /* Calculate shift to align block-ack bits with our Tx window bits */
4210 sh
= agg
->start_idx
- SEQ_TO_INDEX(seq_ctl
>>4);
4211 if (sh
< 0) /* tbw something is wrong with indices */
4214 /* don't use 64-bit values for now */
4215 bitmap
= le64_to_cpu(ba_resp
->bitmap
) >> sh
;
4217 if (agg
->frame_count
> (64 - sh
)) {
4218 IWL_DEBUG_TX_REPLY("more frames than bitmap size");
4222 /* check for success or failure according to the
4223 * transmitted bitmap and block-ack bitmap */
4224 bitmap
&= agg
->bitmap
;
4226 /* For each frame attempted in aggregation,
4227 * update driver's record of tx frame's status. */
4228 for (i
= 0; i
< agg
->frame_count
; i
++) {
4229 ack
= bitmap
& (1 << i
);
4231 IWL_DEBUG_TX_REPLY("%s ON i=%d idx=%d raw=%d\n",
4232 ack
? "ACK":"NACK", i
, (agg
->start_idx
+ i
) & 0xff,
4233 agg
->start_idx
+ i
);
4236 tx_status
= &priv
->txq
[scd_flow
].txb
[agg
->start_idx
].status
;
4237 tx_status
->flags
= IEEE80211_TX_STATUS_ACK
;
4238 tx_status
->flags
|= IEEE80211_TX_STATUS_AMPDU
;
4239 tx_status
->ampdu_ack_map
= successes
;
4240 tx_status
->ampdu_ack_len
= agg
->frame_count
;
4241 iwl4965_hwrate_to_tx_control(priv
, agg
->rate_n_flags
,
4242 &tx_status
->control
);
4244 IWL_DEBUG_TX_REPLY("Bitmap %llx\n", (unsigned long long)bitmap
);
4250 * iwl4965_tx_queue_stop_scheduler - Stop queue, but keep configuration
4252 static void iwl4965_tx_queue_stop_scheduler(struct iwl_priv
*priv
,
4255 /* Simply stop the queue, but don't change any configuration;
4256 * the SCD_ACT_EN bit is the write-enable mask for the ACTIVE bit. */
4257 iwl4965_write_prph(priv
,
4258 KDR_SCD_QUEUE_STATUS_BITS(txq_id
),
4259 (0 << SCD_QUEUE_STTS_REG_POS_ACTIVE
)|
4260 (1 << SCD_QUEUE_STTS_REG_POS_SCD_ACT_EN
));
4264 * txq_id must be greater than IWL_BACK_QUEUE_FIRST_ID
4265 * priv->lock must be held by the caller
4267 static int iwl4965_tx_queue_agg_disable(struct iwl_priv
*priv
, u16 txq_id
,
4268 u16 ssn_idx
, u8 tx_fifo
)
4272 if (IWL_BACK_QUEUE_FIRST_ID
> txq_id
) {
4273 IWL_WARNING("queue number too small: %d, must be > %d\n",
4274 txq_id
, IWL_BACK_QUEUE_FIRST_ID
);
4278 ret
= iwl4965_grab_nic_access(priv
);
4282 iwl4965_tx_queue_stop_scheduler(priv
, txq_id
);
4284 iwl4965_clear_bits_prph(priv
, KDR_SCD_QUEUECHAIN_SEL
, (1 << txq_id
));
4286 priv
->txq
[txq_id
].q
.read_ptr
= (ssn_idx
& 0xff);
4287 priv
->txq
[txq_id
].q
.write_ptr
= (ssn_idx
& 0xff);
4288 /* supposes that ssn_idx is valid (!= 0xFFF) */
4289 iwl4965_set_wr_ptrs(priv
, txq_id
, ssn_idx
);
4291 iwl4965_clear_bits_prph(priv
, KDR_SCD_INTERRUPT_MASK
, (1 << txq_id
));
4292 iwl4965_txq_ctx_deactivate(priv
, txq_id
);
4293 iwl4965_tx_queue_set_status(priv
, &priv
->txq
[txq_id
], tx_fifo
, 0);
4295 iwl4965_release_nic_access(priv
);
4300 int iwl4965_check_empty_hw_queue(struct iwl_priv
*priv
, int sta_id
,
4303 struct iwl4965_queue
*q
= &priv
->txq
[txq_id
].q
;
4304 u8
*addr
= priv
->stations
[sta_id
].sta
.sta
.addr
;
4305 struct iwl4965_tid_data
*tid_data
= &priv
->stations
[sta_id
].tid
[tid
];
4307 switch (priv
->stations
[sta_id
].tid
[tid
].agg
.state
) {
4308 case IWL_EMPTYING_HW_QUEUE_DELBA
:
4309 /* We are reclaiming the last packet of the */
4310 /* aggregated HW queue */
4311 if (txq_id
== tid_data
->agg
.txq_id
&&
4312 q
->read_ptr
== q
->write_ptr
) {
4313 u16 ssn
= SEQ_TO_SN(tid_data
->seq_number
);
4314 int tx_fifo
= default_tid_to_tx_fifo
[tid
];
4315 IWL_DEBUG_HT("HW queue empty: continue DELBA flow\n");
4316 iwl4965_tx_queue_agg_disable(priv
, txq_id
,
4318 tid_data
->agg
.state
= IWL_AGG_OFF
;
4319 ieee80211_stop_tx_ba_cb_irqsafe(priv
->hw
, addr
, tid
);
4322 case IWL_EMPTYING_HW_QUEUE_ADDBA
:
4323 /* We are reclaiming the last packet of the queue */
4324 if (tid_data
->tfds_in_queue
== 0) {
4325 IWL_DEBUG_HT("HW queue empty: continue ADDBA flow\n");
4326 tid_data
->agg
.state
= IWL_AGG_ON
;
4327 ieee80211_start_tx_ba_cb_irqsafe(priv
->hw
, addr
, tid
);
4335 * iwl4965_queue_dec_wrap - Decrement queue index, wrap back to end if needed
4336 * @index -- current index
4337 * @n_bd -- total number of entries in queue (s/b power of 2)
4339 static inline int iwl4965_queue_dec_wrap(int index
, int n_bd
)
4341 return (index
== 0) ? n_bd
- 1 : index
- 1;
4345 * iwl4965_rx_reply_compressed_ba - Handler for REPLY_COMPRESSED_BA
4347 * Handles block-acknowledge notification from device, which reports success
4348 * of frames sent via aggregation.
4350 static void iwl4965_rx_reply_compressed_ba(struct iwl_priv
*priv
,
4351 struct iwl4965_rx_mem_buffer
*rxb
)
4353 struct iwl4965_rx_packet
*pkt
= (void *)rxb
->skb
->data
;
4354 struct iwl4965_compressed_ba_resp
*ba_resp
= &pkt
->u
.compressed_ba
;
4356 struct iwl4965_tx_queue
*txq
= NULL
;
4357 struct iwl4965_ht_agg
*agg
;
4358 DECLARE_MAC_BUF(mac
);
4360 /* "flow" corresponds to Tx queue */
4361 u16 scd_flow
= le16_to_cpu(ba_resp
->scd_flow
);
4363 /* "ssn" is start of block-ack Tx window, corresponds to index
4364 * (in Tx queue's circular buffer) of first TFD/frame in window */
4365 u16 ba_resp_scd_ssn
= le16_to_cpu(ba_resp
->scd_ssn
);
4367 if (scd_flow
>= ARRAY_SIZE(priv
->txq
)) {
4368 IWL_ERROR("BUG_ON scd_flow is bigger than number of queues");
4372 txq
= &priv
->txq
[scd_flow
];
4373 agg
= &priv
->stations
[ba_resp
->sta_id
].tid
[ba_resp
->tid
].agg
;
4375 /* Find index just before block-ack window */
4376 index
= iwl4965_queue_dec_wrap(ba_resp_scd_ssn
& 0xff, txq
->q
.n_bd
);
4378 /* TODO: Need to get this copy more safely - now good for debug */
4380 IWL_DEBUG_TX_REPLY("REPLY_COMPRESSED_BA [%d]Received from %s, "
4383 print_mac(mac
, (u8
*) &ba_resp
->sta_addr_lo32
),
4385 IWL_DEBUG_TX_REPLY("TID = %d, SeqCtl = %d, bitmap = 0x%llx, scd_flow = "
4386 "%d, scd_ssn = %d\n",
4389 (unsigned long long)le64_to_cpu(ba_resp
->bitmap
),
4392 IWL_DEBUG_TX_REPLY("DAT start_idx = %d, bitmap = 0x%llx \n",
4394 (unsigned long long)agg
->bitmap
);
4396 /* Update driver's record of ACK vs. not for each frame in window */
4397 iwl4965_tx_status_reply_compressed_ba(priv
, agg
, ba_resp
);
4399 /* Release all TFDs before the SSN, i.e. all TFDs in front of
4400 * block-ack window (we assume that they've been successfully
4401 * transmitted ... if not, it's too late anyway). */
4402 if (txq
->q
.read_ptr
!= (ba_resp_scd_ssn
& 0xff)) {
4403 int freed
= iwl4965_tx_queue_reclaim(priv
, scd_flow
, index
);
4404 priv
->stations
[ba_resp
->sta_id
].
4405 tid
[ba_resp
->tid
].tfds_in_queue
-= freed
;
4406 if (iwl4965_queue_space(&txq
->q
) > txq
->q
.low_mark
&&
4407 priv
->mac80211_registered
&&
4408 agg
->state
!= IWL_EMPTYING_HW_QUEUE_DELBA
)
4409 ieee80211_wake_queue(priv
->hw
, scd_flow
);
4410 iwl4965_check_empty_hw_queue(priv
, ba_resp
->sta_id
,
4411 ba_resp
->tid
, scd_flow
);
4416 * iwl4965_tx_queue_set_q2ratid - Map unique receiver/tid combination to a queue
4418 static int iwl4965_tx_queue_set_q2ratid(struct iwl_priv
*priv
, u16 ra_tid
,
4425 scd_q2ratid
= ra_tid
& SCD_QUEUE_RA_TID_MAP_RATID_MSK
;
4427 tbl_dw_addr
= priv
->scd_base_addr
+
4428 SCD_TRANSLATE_TBL_OFFSET_QUEUE(txq_id
);
4430 tbl_dw
= iwl4965_read_targ_mem(priv
, tbl_dw_addr
);
4433 tbl_dw
= (scd_q2ratid
<< 16) | (tbl_dw
& 0x0000FFFF);
4435 tbl_dw
= scd_q2ratid
| (tbl_dw
& 0xFFFF0000);
4437 iwl4965_write_targ_mem(priv
, tbl_dw_addr
, tbl_dw
);
4444 * iwl4965_tx_queue_agg_enable - Set up & enable aggregation for selected queue
4446 * NOTE: txq_id must be greater than IWL_BACK_QUEUE_FIRST_ID,
4447 * i.e. it must be one of the higher queues used for aggregation
4449 static int iwl4965_tx_queue_agg_enable(struct iwl_priv
*priv
, int txq_id
,
4450 int tx_fifo
, int sta_id
, int tid
,
4453 unsigned long flags
;
4457 if (IWL_BACK_QUEUE_FIRST_ID
> txq_id
)
4458 IWL_WARNING("queue number too small: %d, must be > %d\n",
4459 txq_id
, IWL_BACK_QUEUE_FIRST_ID
);
4461 ra_tid
= BUILD_RAxTID(sta_id
, tid
);
4463 /* Modify device's station table to Tx this TID */
4464 iwl4965_sta_modify_enable_tid_tx(priv
, sta_id
, tid
);
4466 spin_lock_irqsave(&priv
->lock
, flags
);
4467 rc
= iwl4965_grab_nic_access(priv
);
4469 spin_unlock_irqrestore(&priv
->lock
, flags
);
4473 /* Stop this Tx queue before configuring it */
4474 iwl4965_tx_queue_stop_scheduler(priv
, txq_id
);
4476 /* Map receiver-address / traffic-ID to this queue */
4477 iwl4965_tx_queue_set_q2ratid(priv
, ra_tid
, txq_id
);
4479 /* Set this queue as a chain-building queue */
4480 iwl4965_set_bits_prph(priv
, KDR_SCD_QUEUECHAIN_SEL
, (1 << txq_id
));
4482 /* Place first TFD at index corresponding to start sequence number.
4483 * Assumes that ssn_idx is valid (!= 0xFFF) */
4484 priv
->txq
[txq_id
].q
.read_ptr
= (ssn_idx
& 0xff);
4485 priv
->txq
[txq_id
].q
.write_ptr
= (ssn_idx
& 0xff);
4486 iwl4965_set_wr_ptrs(priv
, txq_id
, ssn_idx
);
4488 /* Set up Tx window size and frame limit for this queue */
4489 iwl4965_write_targ_mem(priv
,
4490 priv
->scd_base_addr
+ SCD_CONTEXT_QUEUE_OFFSET(txq_id
),
4491 (SCD_WIN_SIZE
<< SCD_QUEUE_CTX_REG1_WIN_SIZE_POS
) &
4492 SCD_QUEUE_CTX_REG1_WIN_SIZE_MSK
);
4494 iwl4965_write_targ_mem(priv
, priv
->scd_base_addr
+
4495 SCD_CONTEXT_QUEUE_OFFSET(txq_id
) + sizeof(u32
),
4496 (SCD_FRAME_LIMIT
<< SCD_QUEUE_CTX_REG2_FRAME_LIMIT_POS
)
4497 & SCD_QUEUE_CTX_REG2_FRAME_LIMIT_MSK
);
4499 iwl4965_set_bits_prph(priv
, KDR_SCD_INTERRUPT_MASK
, (1 << txq_id
));
4501 /* Set up Status area in SRAM, map to Tx DMA/FIFO, activate the queue */
4502 iwl4965_tx_queue_set_status(priv
, &priv
->txq
[txq_id
], tx_fifo
, 1);
4504 iwl4965_release_nic_access(priv
);
4505 spin_unlock_irqrestore(&priv
->lock
, flags
);
4510 #endif /* CONFIG_IWL4965_HT */
4513 * iwl4965_add_station - Initialize a station's hardware rate table
4515 * The uCode's station table contains a table of fallback rates
4516 * for automatic fallback during transmission.
4518 * NOTE: This sets up a default set of values. These will be replaced later
4519 * if the driver's iwl-4965-rs rate scaling algorithm is used, instead of
4522 * NOTE: Run REPLY_ADD_STA command to set up station table entry, before
4523 * calling this function (which runs REPLY_TX_LINK_QUALITY_CMD,
4524 * which requires station table entry to exist).
4526 void iwl4965_add_station(struct iwl_priv
*priv
, const u8
*addr
, int is_ap
)
4529 struct iwl4965_link_quality_cmd link_cmd
= {
4534 /* Set up the rate scaling to start at selected rate, fall back
4535 * all the way down to 1M in IEEE order, and then spin on 1M */
4537 r
= IWL_RATE_54M_INDEX
;
4538 else if (priv
->band
== IEEE80211_BAND_5GHZ
)
4539 r
= IWL_RATE_6M_INDEX
;
4541 r
= IWL_RATE_1M_INDEX
;
4543 for (i
= 0; i
< LINK_QUAL_MAX_RETRY_NUM
; i
++) {
4545 if (r
>= IWL_FIRST_CCK_RATE
&& r
<= IWL_LAST_CCK_RATE
)
4546 rate_flags
|= RATE_MCS_CCK_MSK
;
4548 /* Use Tx antenna B only */
4549 rate_flags
|= RATE_MCS_ANT_B_MSK
;
4550 rate_flags
&= ~RATE_MCS_ANT_A_MSK
;
4552 link_cmd
.rs_table
[i
].rate_n_flags
=
4553 iwl4965_hw_set_rate_n_flags(iwl4965_rates
[r
].plcp
, rate_flags
);
4554 r
= iwl4965_get_prev_ieee_rate(r
);
4557 link_cmd
.general_params
.single_stream_ant_msk
= 2;
4558 link_cmd
.general_params
.dual_stream_ant_msk
= 3;
4559 link_cmd
.agg_params
.agg_dis_start_th
= 3;
4560 link_cmd
.agg_params
.agg_time_limit
= cpu_to_le16(4000);
4562 /* Update the rate scaling for control frame Tx to AP */
4563 link_cmd
.sta_id
= is_ap
? IWL_AP_ID
: priv
->hw_setting
.bcast_sta_id
;
4565 iwl4965_send_cmd_pdu(priv
, REPLY_TX_LINK_QUALITY_CMD
, sizeof(link_cmd
),
4569 #ifdef CONFIG_IWL4965_HT
4571 static u8
iwl4965_is_channel_extension(struct iwl_priv
*priv
,
4572 enum ieee80211_band band
,
4573 u16 channel
, u8 extension_chan_offset
)
4575 const struct iwl_channel_info
*ch_info
;
4577 ch_info
= iwl4965_get_channel_info(priv
, band
, channel
);
4578 if (!is_channel_valid(ch_info
))
4581 if (extension_chan_offset
== IWL_EXT_CHANNEL_OFFSET_NONE
)
4584 if ((ch_info
->fat_extension_channel
== extension_chan_offset
) ||
4585 (ch_info
->fat_extension_channel
== HT_IE_EXT_CHANNEL_MAX
))
4591 static u8
iwl4965_is_fat_tx_allowed(struct iwl_priv
*priv
,
4592 struct ieee80211_ht_info
*sta_ht_inf
)
4594 struct iwl_ht_info
*iwl_ht_conf
= &priv
->current_ht_config
;
4596 if ((!iwl_ht_conf
->is_ht
) ||
4597 (iwl_ht_conf
->supported_chan_width
!= IWL_CHANNEL_WIDTH_40MHZ
) ||
4598 (iwl_ht_conf
->extension_chan_offset
== IWL_EXT_CHANNEL_OFFSET_NONE
))
4602 if ((!sta_ht_inf
->ht_supported
) ||
4603 (!(sta_ht_inf
->cap
& IEEE80211_HT_CAP_SUP_WIDTH
)))
4607 return (iwl4965_is_channel_extension(priv
, priv
->band
,
4608 iwl_ht_conf
->control_channel
,
4609 iwl_ht_conf
->extension_chan_offset
));
4612 void iwl4965_set_rxon_ht(struct iwl_priv
*priv
, struct iwl_ht_info
*ht_info
)
4614 struct iwl4965_rxon_cmd
*rxon
= &priv
->staging_rxon
;
4617 if (!ht_info
->is_ht
)
4620 /* Set up channel bandwidth: 20 MHz only, or 20/40 mixed if fat ok */
4621 if (iwl4965_is_fat_tx_allowed(priv
, NULL
))
4622 rxon
->flags
|= RXON_FLG_CHANNEL_MODE_MIXED_MSK
;
4624 rxon
->flags
&= ~(RXON_FLG_CHANNEL_MODE_MIXED_MSK
|
4625 RXON_FLG_CHANNEL_MODE_PURE_40_MSK
);
4627 if (le16_to_cpu(rxon
->channel
) != ht_info
->control_channel
) {
4628 IWL_DEBUG_ASSOC("control diff than current %d %d\n",
4629 le16_to_cpu(rxon
->channel
),
4630 ht_info
->control_channel
);
4631 rxon
->channel
= cpu_to_le16(ht_info
->control_channel
);
4635 /* Note: control channel is opposite of extension channel */
4636 switch (ht_info
->extension_chan_offset
) {
4637 case IWL_EXT_CHANNEL_OFFSET_ABOVE
:
4638 rxon
->flags
&= ~(RXON_FLG_CTRL_CHANNEL_LOC_HI_MSK
);
4640 case IWL_EXT_CHANNEL_OFFSET_BELOW
:
4641 rxon
->flags
|= RXON_FLG_CTRL_CHANNEL_LOC_HI_MSK
;
4643 case IWL_EXT_CHANNEL_OFFSET_NONE
:
4645 rxon
->flags
&= ~RXON_FLG_CHANNEL_MODE_MIXED_MSK
;
4649 val
= ht_info
->ht_protection
;
4651 rxon
->flags
|= cpu_to_le32(val
<< RXON_FLG_HT_OPERATING_MODE_POS
);
4653 iwl4965_set_rxon_chain(priv
);
4655 IWL_DEBUG_ASSOC("supported HT rate 0x%X %X "
4656 "rxon flags 0x%X operation mode :0x%X "
4657 "extension channel offset 0x%x "
4658 "control chan %d\n",
4659 ht_info
->supp_mcs_set
[0], ht_info
->supp_mcs_set
[1],
4660 le32_to_cpu(rxon
->flags
), ht_info
->ht_protection
,
4661 ht_info
->extension_chan_offset
,
4662 ht_info
->control_channel
);
4666 void iwl4965_set_ht_add_station(struct iwl_priv
*priv
, u8 index
,
4667 struct ieee80211_ht_info
*sta_ht_inf
)
4672 if (!sta_ht_inf
|| !sta_ht_inf
->ht_supported
)
4675 mimo_ps_mode
= (sta_ht_inf
->cap
& IEEE80211_HT_CAP_MIMO_PS
) >> 2;
4677 sta_flags
= priv
->stations
[index
].sta
.station_flags
;
4679 sta_flags
&= ~(STA_FLG_RTS_MIMO_PROT_MSK
| STA_FLG_MIMO_DIS_MSK
);
4681 switch (mimo_ps_mode
) {
4682 case WLAN_HT_CAP_MIMO_PS_STATIC
:
4683 sta_flags
|= STA_FLG_MIMO_DIS_MSK
;
4685 case WLAN_HT_CAP_MIMO_PS_DYNAMIC
:
4686 sta_flags
|= STA_FLG_RTS_MIMO_PROT_MSK
;
4688 case WLAN_HT_CAP_MIMO_PS_DISABLED
:
4691 IWL_WARNING("Invalid MIMO PS mode %d", mimo_ps_mode
);
4695 sta_flags
|= cpu_to_le32(
4696 (u32
)sta_ht_inf
->ampdu_factor
<< STA_FLG_MAX_AGG_SIZE_POS
);
4698 sta_flags
|= cpu_to_le32(
4699 (u32
)sta_ht_inf
->ampdu_density
<< STA_FLG_AGG_MPDU_DENSITY_POS
);
4701 if (iwl4965_is_fat_tx_allowed(priv
, sta_ht_inf
))
4702 sta_flags
|= STA_FLG_FAT_EN_MSK
;
4704 sta_flags
&= ~STA_FLG_FAT_EN_MSK
;
4706 priv
->stations
[index
].sta
.station_flags
= sta_flags
;
4711 static void iwl4965_sta_modify_add_ba_tid(struct iwl_priv
*priv
,
4712 int sta_id
, int tid
, u16 ssn
)
4714 unsigned long flags
;
4716 spin_lock_irqsave(&priv
->sta_lock
, flags
);
4717 priv
->stations
[sta_id
].sta
.station_flags_msk
= 0;
4718 priv
->stations
[sta_id
].sta
.sta
.modify_mask
= STA_MODIFY_ADDBA_TID_MSK
;
4719 priv
->stations
[sta_id
].sta
.add_immediate_ba_tid
= (u8
)tid
;
4720 priv
->stations
[sta_id
].sta
.add_immediate_ba_ssn
= cpu_to_le16(ssn
);
4721 priv
->stations
[sta_id
].sta
.mode
= STA_CONTROL_MODIFY_MSK
;
4722 spin_unlock_irqrestore(&priv
->sta_lock
, flags
);
4724 iwl4965_send_add_station(priv
, &priv
->stations
[sta_id
].sta
, CMD_ASYNC
);
4727 static void iwl4965_sta_modify_del_ba_tid(struct iwl_priv
*priv
,
4728 int sta_id
, int tid
)
4730 unsigned long flags
;
4732 spin_lock_irqsave(&priv
->sta_lock
, flags
);
4733 priv
->stations
[sta_id
].sta
.station_flags_msk
= 0;
4734 priv
->stations
[sta_id
].sta
.sta
.modify_mask
= STA_MODIFY_DELBA_TID_MSK
;
4735 priv
->stations
[sta_id
].sta
.remove_immediate_ba_tid
= (u8
)tid
;
4736 priv
->stations
[sta_id
].sta
.mode
= STA_CONTROL_MODIFY_MSK
;
4737 spin_unlock_irqrestore(&priv
->sta_lock
, flags
);
4739 iwl4965_send_add_station(priv
, &priv
->stations
[sta_id
].sta
, CMD_ASYNC
);
4743 * Find first available (lowest unused) Tx Queue, mark it "active".
4744 * Called only when finding queue for aggregation.
4745 * Should never return anything < 7, because they should already
4746 * be in use as EDCA AC (0-3), Command (4), HCCA (5, 6).
4748 static int iwl4965_txq_ctx_activate_free(struct iwl_priv
*priv
)
4752 for (txq_id
= 0; txq_id
< priv
->hw_setting
.max_txq_num
; txq_id
++)
4753 if (!test_and_set_bit(txq_id
, &priv
->txq_ctx_active_msk
))
4758 static int iwl4965_mac_ht_tx_agg_start(struct ieee80211_hw
*hw
, const u8
*da
,
4759 u16 tid
, u16
*start_seq_num
)
4761 struct iwl_priv
*priv
= hw
->priv
;
4767 unsigned long flags
;
4768 struct iwl4965_tid_data
*tid_data
;
4769 DECLARE_MAC_BUF(mac
);
4771 if (likely(tid
< ARRAY_SIZE(default_tid_to_tx_fifo
)))
4772 tx_fifo
= default_tid_to_tx_fifo
[tid
];
4776 IWL_WARNING("%s on da = %s tid = %d\n",
4777 __func__
, print_mac(mac
, da
), tid
);
4779 sta_id
= iwl4965_hw_find_station(priv
, da
);
4780 if (sta_id
== IWL_INVALID_STATION
)
4783 if (priv
->stations
[sta_id
].tid
[tid
].agg
.state
!= IWL_AGG_OFF
) {
4784 IWL_ERROR("Start AGG when state is not IWL_AGG_OFF !\n");
4788 txq_id
= iwl4965_txq_ctx_activate_free(priv
);
4792 spin_lock_irqsave(&priv
->sta_lock
, flags
);
4793 tid_data
= &priv
->stations
[sta_id
].tid
[tid
];
4794 ssn
= SEQ_TO_SN(tid_data
->seq_number
);
4795 tid_data
->agg
.txq_id
= txq_id
;
4796 spin_unlock_irqrestore(&priv
->sta_lock
, flags
);
4798 *start_seq_num
= ssn
;
4799 ret
= iwl4965_tx_queue_agg_enable(priv
, txq_id
, tx_fifo
,
4805 if (tid_data
->tfds_in_queue
== 0) {
4806 printk(KERN_ERR
"HW queue is empty\n");
4807 tid_data
->agg
.state
= IWL_AGG_ON
;
4808 ieee80211_start_tx_ba_cb_irqsafe(hw
, da
, tid
);
4810 IWL_DEBUG_HT("HW queue is NOT empty: %d packets in HW queue\n",
4811 tid_data
->tfds_in_queue
);
4812 tid_data
->agg
.state
= IWL_EMPTYING_HW_QUEUE_ADDBA
;
4817 static int iwl4965_mac_ht_tx_agg_stop(struct ieee80211_hw
*hw
, const u8
*da
,
4821 struct iwl_priv
*priv
= hw
->priv
;
4822 int tx_fifo_id
, txq_id
, sta_id
, ssn
= -1;
4823 struct iwl4965_tid_data
*tid_data
;
4824 int ret
, write_ptr
, read_ptr
;
4825 unsigned long flags
;
4826 DECLARE_MAC_BUF(mac
);
4829 IWL_ERROR("da = NULL\n");
4833 if (likely(tid
< ARRAY_SIZE(default_tid_to_tx_fifo
)))
4834 tx_fifo_id
= default_tid_to_tx_fifo
[tid
];
4838 sta_id
= iwl4965_hw_find_station(priv
, da
);
4840 if (sta_id
== IWL_INVALID_STATION
)
4843 if (priv
->stations
[sta_id
].tid
[tid
].agg
.state
!= IWL_AGG_ON
)
4844 IWL_WARNING("Stopping AGG while state not IWL_AGG_ON\n");
4846 tid_data
= &priv
->stations
[sta_id
].tid
[tid
];
4847 ssn
= (tid_data
->seq_number
& IEEE80211_SCTL_SEQ
) >> 4;
4848 txq_id
= tid_data
->agg
.txq_id
;
4849 write_ptr
= priv
->txq
[txq_id
].q
.write_ptr
;
4850 read_ptr
= priv
->txq
[txq_id
].q
.read_ptr
;
4852 /* The queue is not empty */
4853 if (write_ptr
!= read_ptr
) {
4854 IWL_DEBUG_HT("Stopping a non empty AGG HW QUEUE\n");
4855 priv
->stations
[sta_id
].tid
[tid
].agg
.state
=
4856 IWL_EMPTYING_HW_QUEUE_DELBA
;
4860 IWL_DEBUG_HT("HW queue empty\n");;
4861 priv
->stations
[sta_id
].tid
[tid
].agg
.state
= IWL_AGG_OFF
;
4863 spin_lock_irqsave(&priv
->lock
, flags
);
4864 ret
= iwl4965_tx_queue_agg_disable(priv
, txq_id
, ssn
, tx_fifo_id
);
4865 spin_unlock_irqrestore(&priv
->lock
, flags
);
4870 ieee80211_stop_tx_ba_cb_irqsafe(priv
->hw
, da
, tid
);
4872 IWL_DEBUG_INFO("iwl4965_mac_ht_tx_agg_stop on da=%s tid=%d\n",
4873 print_mac(mac
, da
), tid
);
4878 int iwl4965_mac_ampdu_action(struct ieee80211_hw
*hw
,
4879 enum ieee80211_ampdu_mlme_action action
,
4880 const u8
*addr
, u16 tid
, u16
*ssn
)
4882 struct iwl_priv
*priv
= hw
->priv
;
4884 DECLARE_MAC_BUF(mac
);
4886 IWL_DEBUG_HT("A-MPDU action on da=%s tid=%d ",
4887 print_mac(mac
, addr
), tid
);
4888 sta_id
= iwl4965_hw_find_station(priv
, addr
);
4890 case IEEE80211_AMPDU_RX_START
:
4891 IWL_DEBUG_HT("start Rx\n");
4892 iwl4965_sta_modify_add_ba_tid(priv
, sta_id
, tid
, *ssn
);
4894 case IEEE80211_AMPDU_RX_STOP
:
4895 IWL_DEBUG_HT("stop Rx\n");
4896 iwl4965_sta_modify_del_ba_tid(priv
, sta_id
, tid
);
4898 case IEEE80211_AMPDU_TX_START
:
4899 IWL_DEBUG_HT("start Tx\n");
4900 return iwl4965_mac_ht_tx_agg_start(hw
, addr
, tid
, ssn
);
4901 case IEEE80211_AMPDU_TX_STOP
:
4902 IWL_DEBUG_HT("stop Tx\n");
4903 return iwl4965_mac_ht_tx_agg_stop(hw
, addr
, tid
);
4905 IWL_DEBUG_HT("unknown\n");
4912 #endif /* CONFIG_IWL4965_HT */
4914 /* Set up 4965-specific Rx frame reply handlers */
4915 void iwl4965_hw_rx_handler_setup(struct iwl_priv
*priv
)
4917 /* Legacy Rx frames */
4918 priv
->rx_handlers
[REPLY_4965_RX
] = iwl4965_rx_reply_rx
;
4920 /* High-throughput (HT) Rx frames */
4921 priv
->rx_handlers
[REPLY_RX_PHY_CMD
] = iwl4965_rx_reply_rx_phy
;
4922 priv
->rx_handlers
[REPLY_RX_MPDU_CMD
] = iwl4965_rx_reply_rx
;
4924 priv
->rx_handlers
[MISSED_BEACONS_NOTIFICATION
] =
4925 iwl4965_rx_missed_beacon_notif
;
4927 #ifdef CONFIG_IWL4965_HT
4928 priv
->rx_handlers
[REPLY_COMPRESSED_BA
] = iwl4965_rx_reply_compressed_ba
;
4929 #endif /* CONFIG_IWL4965_HT */
4932 void iwl4965_hw_setup_deferred_work(struct iwl_priv
*priv
)
4934 INIT_WORK(&priv
->txpower_work
, iwl4965_bg_txpower_work
);
4935 INIT_WORK(&priv
->statistics_work
, iwl4965_bg_statistics_work
);
4936 #ifdef CONFIG_IWL4965_SENSITIVITY
4937 INIT_WORK(&priv
->sensitivity_work
, iwl4965_bg_sensitivity_work
);
4939 init_timer(&priv
->statistics_periodic
);
4940 priv
->statistics_periodic
.data
= (unsigned long)priv
;
4941 priv
->statistics_periodic
.function
= iwl4965_bg_statistics_periodic
;
4944 void iwl4965_hw_cancel_deferred_work(struct iwl_priv
*priv
)
4946 del_timer_sync(&priv
->statistics_periodic
);
4948 cancel_delayed_work(&priv
->init_alive_start
);
4951 static struct iwl_lib_ops iwl4965_lib
= {
4952 .init_drv
= iwl4965_init_drv
,
4954 .verify_signature
= iwlcore_eeprom_verify_signature
,
4955 .acquire_semaphore
= iwlcore_eeprom_acquire_semaphore
,
4956 .release_semaphore
= iwlcore_eeprom_release_semaphore
,
4960 static struct iwl_ops iwl4965_ops
= {
4961 .lib
= &iwl4965_lib
,
4964 static struct iwl_cfg iwl4965_agn_cfg
= {
4966 .fw_name
= "iwlwifi-4965" IWL4965_UCODE_API
".ucode",
4967 .sku
= IWL_SKU_A
|IWL_SKU_G
|IWL_SKU_N
,
4968 .ops
= &iwl4965_ops
,
4971 struct pci_device_id iwl4965_hw_card_ids
[] = {
4972 {IWL_PCI_DEVICE(0x4229, PCI_ANY_ID
, iwl4965_agn_cfg
)},
4973 {IWL_PCI_DEVICE(0x4230, PCI_ANY_ID
, iwl4965_agn_cfg
)},
4977 MODULE_DEVICE_TABLE(pci
, iwl4965_hw_card_ids
);