projects / deliverable / linux.git / blob
? search:
summary | shortlog | log | commit | commitdiff | tree
blame | history | raw | HEAD
rtl818x: change misleading names for few register bit definitions
[deliverable/linux.git] / drivers / net / wireless / rtl818x / rtl8187 / dev.c
1 /*
2 * Linux device driver for RTL8187
3 *
4 * Copyright 2007 Michael Wu <flamingice@sourmilk.net>
5 * Copyright 2007 Andrea Merello <andrea.merello@gmail.com>
6 *
7 * Based on the r8187 driver, which is:
8 * Copyright 2005 Andrea Merello <andrea.merello@gmail.com>, et al.
9 *
10 * The driver was extended to the RTL8187B in 2008 by:
11 * Herton Ronaldo Krzesinski <herton@mandriva.com.br>
12 * Hin-Tak Leung <htl10@users.sourceforge.net>
13 * Larry Finger <Larry.Finger@lwfinger.net>
14 *
15 * Magic delays and register offsets below are taken from the original
16 * r8187 driver sources. Thanks to Realtek for their support!
17 *
18 * This program is free software; you can redistribute it and/or modify
19 * it under the terms of the GNU General Public License version 2 as
20 * published by the Free Software Foundation.
21 */
22
23 #include <linux/usb.h>
24 #include <linux/slab.h>
25 #include <linux/delay.h>
26 #include <linux/etherdevice.h>
27 #include <linux/eeprom_93cx6.h>
28 #include <linux/module.h>
29 #include <net/mac80211.h>
30
31 #include "rtl8187.h"
32 #include "rtl8225.h"
33 #ifdef CONFIG_RTL8187_LEDS
34 #include "leds.h"
35 #endif
36 #include "rfkill.h"
37
38 MODULE_AUTHOR("Michael Wu <flamingice@sourmilk.net>");
39 MODULE_AUTHOR("Andrea Merello <andrea.merello@gmail.com>");
40 MODULE_AUTHOR("Herton Ronaldo Krzesinski <herton@mandriva.com.br>");
41 MODULE_AUTHOR("Hin-Tak Leung <htl10@users.sourceforge.net>");
42 MODULE_AUTHOR("Larry Finger <Larry.Finger@lwfinger.net>");
43 MODULE_DESCRIPTION("RTL8187/RTL8187B USB wireless driver");
44 MODULE_LICENSE("GPL");
45
46 static struct usb_device_id rtl8187_table[] = {
47 /* Asus */
48 {USB_DEVICE(0x0b05, 0x171d), .driver_info = DEVICE_RTL8187},
49 /* Belkin */
50 {USB_DEVICE(0x050d, 0x705e), .driver_info = DEVICE_RTL8187B},
51 /* Realtek */
52 {USB_DEVICE(0x0bda, 0x8187), .driver_info = DEVICE_RTL8187},
53 {USB_DEVICE(0x0bda, 0x8189), .driver_info = DEVICE_RTL8187B},
54 {USB_DEVICE(0x0bda, 0x8197), .driver_info = DEVICE_RTL8187B},
55 {USB_DEVICE(0x0bda, 0x8198), .driver_info = DEVICE_RTL8187B},
56 /* Surecom */
57 {USB_DEVICE(0x0769, 0x11F2), .driver_info = DEVICE_RTL8187},
58 /* Logitech */
59 {USB_DEVICE(0x0789, 0x010C), .driver_info = DEVICE_RTL8187},
60 /* Netgear */
61 {USB_DEVICE(0x0846, 0x6100), .driver_info = DEVICE_RTL8187},
62 {USB_DEVICE(0x0846, 0x6a00), .driver_info = DEVICE_RTL8187},
63 {USB_DEVICE(0x0846, 0x4260), .driver_info = DEVICE_RTL8187B},
64 /* HP */
65 {USB_DEVICE(0x03f0, 0xca02), .driver_info = DEVICE_RTL8187},
66 /* Sitecom */
67 {USB_DEVICE(0x0df6, 0x000d), .driver_info = DEVICE_RTL8187},
68 {USB_DEVICE(0x0df6, 0x0028), .driver_info = DEVICE_RTL8187B},
69 {USB_DEVICE(0x0df6, 0x0029), .driver_info = DEVICE_RTL8187B},
70 /* Sphairon Access Systems GmbH */
71 {USB_DEVICE(0x114B, 0x0150), .driver_info = DEVICE_RTL8187},
72 /* Dick Smith Electronics */
73 {USB_DEVICE(0x1371, 0x9401), .driver_info = DEVICE_RTL8187},
74 /* Abocom */
75 {USB_DEVICE(0x13d1, 0xabe6), .driver_info = DEVICE_RTL8187},
76 /* Qcom */
77 {USB_DEVICE(0x18E8, 0x6232), .driver_info = DEVICE_RTL8187},
78 /* AirLive */
79 {USB_DEVICE(0x1b75, 0x8187), .driver_info = DEVICE_RTL8187},
80 /* Linksys */
81 {USB_DEVICE(0x1737, 0x0073), .driver_info = DEVICE_RTL8187B},
82 {}
83 };
84
85 MODULE_DEVICE_TABLE(usb, rtl8187_table);
86
87 static const struct ieee80211_rate rtl818x_rates[] = {
88 { .bitrate = 10, .hw_value = 0, },
89 { .bitrate = 20, .hw_value = 1, },
90 { .bitrate = 55, .hw_value = 2, },
91 { .bitrate = 110, .hw_value = 3, },
92 { .bitrate = 60, .hw_value = 4, },
93 { .bitrate = 90, .hw_value = 5, },
94 { .bitrate = 120, .hw_value = 6, },
95 { .bitrate = 180, .hw_value = 7, },
96 { .bitrate = 240, .hw_value = 8, },
97 { .bitrate = 360, .hw_value = 9, },
98 { .bitrate = 480, .hw_value = 10, },
99 { .bitrate = 540, .hw_value = 11, },
100 };
101
102 static const struct ieee80211_channel rtl818x_channels[] = {
103 { .center_freq = 2412 },
104 { .center_freq = 2417 },
105 { .center_freq = 2422 },
106 { .center_freq = 2427 },
107 { .center_freq = 2432 },
108 { .center_freq = 2437 },
109 { .center_freq = 2442 },
110 { .center_freq = 2447 },
111 { .center_freq = 2452 },
112 { .center_freq = 2457 },
113 { .center_freq = 2462 },
114 { .center_freq = 2467 },
115 { .center_freq = 2472 },
116 { .center_freq = 2484 },
117 };
118
119 static void rtl8187_iowrite_async_cb(struct urb *urb)
120 {
121 kfree(urb->context);
122 }
123
124 static void rtl8187_iowrite_async(struct rtl8187_priv *priv, __le16 addr,
125 void *data, u16 len)
126 {
127 struct usb_ctrlrequest *dr;
128 struct urb *urb;
129 struct rtl8187_async_write_data {
130 u8 data[4];
131 struct usb_ctrlrequest dr;
132 } *buf;
133 int rc;
134
135 buf = kmalloc(sizeof(*buf), GFP_ATOMIC);
136 if (!buf)
137 return;
138
139 urb = usb_alloc_urb(0, GFP_ATOMIC);
140 if (!urb) {
141 kfree(buf);
142 return;
143 }
144
145 dr = &buf->dr;
146
147 dr->bRequestType = RTL8187_REQT_WRITE;
148 dr->bRequest = RTL8187_REQ_SET_REG;
149 dr->wValue = addr;
150 dr->wIndex = 0;
151 dr->wLength = cpu_to_le16(len);
152
153 memcpy(buf, data, len);
154
155 usb_fill_control_urb(urb, priv->udev, usb_sndctrlpipe(priv->udev, 0),
156 (unsigned char *)dr, buf, len,
157 rtl8187_iowrite_async_cb, buf);
158 usb_anchor_urb(urb, &priv->anchored);
159 rc = usb_submit_urb(urb, GFP_ATOMIC);
160 if (rc < 0) {
161 kfree(buf);
162 usb_unanchor_urb(urb);
163 }
164 usb_free_urb(urb);
165 }
166
167 static inline void rtl818x_iowrite32_async(struct rtl8187_priv *priv,
168 __le32 *addr, u32 val)
169 {
170 __le32 buf = cpu_to_le32(val);
171
172 rtl8187_iowrite_async(priv, cpu_to_le16((unsigned long)addr),
173 &buf, sizeof(buf));
174 }
175
176 void rtl8187_write_phy(struct ieee80211_hw *dev, u8 addr, u32 data)
177 {
178 struct rtl8187_priv *priv = dev->priv;
179
180 data <<= 8;
181 data |= addr | 0x80;
182
183 rtl818x_iowrite8(priv, &priv->map->PHY[3], (data >> 24) & 0xFF);
184 rtl818x_iowrite8(priv, &priv->map->PHY[2], (data >> 16) & 0xFF);
185 rtl818x_iowrite8(priv, &priv->map->PHY[1], (data >> 8) & 0xFF);
186 rtl818x_iowrite8(priv, &priv->map->PHY[0], data & 0xFF);
187 }
188
189 static void rtl8187_tx_cb(struct urb *urb)
190 {
191 struct sk_buff *skb = (struct sk_buff *)urb->context;
192 struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
193 struct ieee80211_hw *hw = info->rate_driver_data[0];
194 struct rtl8187_priv *priv = hw->priv;
195
196 skb_pull(skb, priv->is_rtl8187b ? sizeof(struct rtl8187b_tx_hdr) :
197 sizeof(struct rtl8187_tx_hdr));
198 ieee80211_tx_info_clear_status(info);
199
200 if (!(urb->status) && !(info->flags & IEEE80211_TX_CTL_NO_ACK)) {
201 if (priv->is_rtl8187b) {
202 skb_queue_tail(&priv->b_tx_status.queue, skb);
203
204 /* queue is "full", discard last items */
205 while (skb_queue_len(&priv->b_tx_status.queue) > 5) {
206 struct sk_buff *old_skb;
207
208 dev_dbg(&priv->udev->dev,
209 "transmit status queue full\n");
210
211 old_skb = skb_dequeue(&priv->b_tx_status.queue);
212 ieee80211_tx_status_irqsafe(hw, old_skb);
213 }
214 return;
215 } else {
216 info->flags |= IEEE80211_TX_STAT_ACK;
217 }
218 }
219 if (priv->is_rtl8187b)
220 ieee80211_tx_status_irqsafe(hw, skb);
221 else {
222 /* Retry information for the RTI8187 is only available by
223 * reading a register in the device. We are in interrupt mode
224 * here, thus queue the skb and finish on a work queue. */
225 skb_queue_tail(&priv->b_tx_status.queue, skb);
226 ieee80211_queue_delayed_work(hw, &priv->work, 0);
227 }
228 }
229
230 static void rtl8187_tx(struct ieee80211_hw *dev,
231 struct ieee80211_tx_control *control,
232 struct sk_buff *skb)
233 {
234 struct rtl8187_priv *priv = dev->priv;
235 struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
236 struct ieee80211_hdr *tx_hdr = (struct ieee80211_hdr *)(skb->data);
237 unsigned int ep;
238 void *buf;
239 struct urb *urb;
240 __le16 rts_dur = 0;
241 u32 flags;
242 int rc;
243
244 urb = usb_alloc_urb(0, GFP_ATOMIC);
245 if (!urb) {
246 kfree_skb(skb);
247 return;
248 }
249
250 flags = skb->len;
251 flags |= RTL818X_TX_DESC_FLAG_NO_ENC;
252
253 flags |= ieee80211_get_tx_rate(dev, info)->hw_value << 24;
254 if (ieee80211_has_morefrags(tx_hdr->frame_control))
255 flags |= RTL818X_TX_DESC_FLAG_MOREFRAG;
256 if (info->control.rates[0].flags & IEEE80211_TX_RC_USE_RTS_CTS) {
257 flags |= RTL818X_TX_DESC_FLAG_RTS;
258 flags |= ieee80211_get_rts_cts_rate(dev, info)->hw_value << 19;
259 rts_dur = ieee80211_rts_duration(dev, priv->vif,
260 skb->len, info);
261 } else if (info->control.rates[0].flags & IEEE80211_TX_RC_USE_CTS_PROTECT) {
262 flags |= RTL818X_TX_DESC_FLAG_CTS;
263 flags |= ieee80211_get_rts_cts_rate(dev, info)->hw_value << 19;
264 }
265
266 if (info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) {
267 if (info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT)
268 priv->seqno += 0x10;
269 tx_hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG);
270 tx_hdr->seq_ctrl |= cpu_to_le16(priv->seqno);
271 }
272
273 if (!priv->is_rtl8187b) {
274 struct rtl8187_tx_hdr *hdr =
275 (struct rtl8187_tx_hdr *)skb_push(skb, sizeof(*hdr));
276 hdr->flags = cpu_to_le32(flags);
277 hdr->len = 0;
278 hdr->rts_duration = rts_dur;
279 hdr->retry = cpu_to_le32((info->control.rates[0].count - 1) << 8);
280 buf = hdr;
281
282 ep = 2;
283 } else {
284 /* fc needs to be calculated before skb_push() */
285 unsigned int epmap[4] = { 6, 7, 5, 4 };
286 u16 fc = le16_to_cpu(tx_hdr->frame_control);
287
288 struct rtl8187b_tx_hdr *hdr =
289 (struct rtl8187b_tx_hdr *)skb_push(skb, sizeof(*hdr));
290 struct ieee80211_rate *txrate =
291 ieee80211_get_tx_rate(dev, info);
292 memset(hdr, 0, sizeof(*hdr));
293 hdr->flags = cpu_to_le32(flags);
294 hdr->rts_duration = rts_dur;
295 hdr->retry = cpu_to_le32((info->control.rates[0].count - 1) << 8);
296 hdr->tx_duration =
297 ieee80211_generic_frame_duration(dev, priv->vif,
298 info->band,
299 skb->len, txrate);
300 buf = hdr;
301
302 if ((fc & IEEE80211_FCTL_FTYPE) == IEEE80211_FTYPE_MGMT)
303 ep = 12;
304 else
305 ep = epmap[skb_get_queue_mapping(skb)];
306 }
307
308 info->rate_driver_data[0] = dev;
309 info->rate_driver_data[1] = urb;
310
311 usb_fill_bulk_urb(urb, priv->udev, usb_sndbulkpipe(priv->udev, ep),
312 buf, skb->len, rtl8187_tx_cb, skb);
313 urb->transfer_flags |= URB_ZERO_PACKET;
314 usb_anchor_urb(urb, &priv->anchored);
315 rc = usb_submit_urb(urb, GFP_ATOMIC);
316 if (rc < 0) {
317 usb_unanchor_urb(urb);
318 kfree_skb(skb);
319 }
320 usb_free_urb(urb);
321 }
322
323 static void rtl8187_rx_cb(struct urb *urb)
324 {
325 struct sk_buff *skb = (struct sk_buff *)urb->context;
326 struct rtl8187_rx_info *info = (struct rtl8187_rx_info *)skb->cb;
327 struct ieee80211_hw *dev = info->dev;
328 struct rtl8187_priv *priv = dev->priv;
329 struct ieee80211_rx_status rx_status = { 0 };
330 int rate, signal;
331 u32 flags;
332 unsigned long f;
333
334 spin_lock_irqsave(&priv->rx_queue.lock, f);
335 __skb_unlink(skb, &priv->rx_queue);
336 spin_unlock_irqrestore(&priv->rx_queue.lock, f);
337 skb_put(skb, urb->actual_length);
338
339 if (unlikely(urb->status)) {
340 dev_kfree_skb_irq(skb);
341 return;
342 }
343
344 if (!priv->is_rtl8187b) {
345 struct rtl8187_rx_hdr *hdr =
346 (typeof(hdr))(skb_tail_pointer(skb) - sizeof(*hdr));
347 flags = le32_to_cpu(hdr->flags);
348 /* As with the RTL8187B below, the AGC is used to calculate
349 * signal strength. In this case, the scaling
350 * constants are derived from the output of p54usb.
351 */
352 signal = -4 - ((27 * hdr->agc) >> 6);
353 rx_status.antenna = (hdr->signal >> 7) & 1;
354 rx_status.mactime = le64_to_cpu(hdr->mac_time);
355 } else {
356 struct rtl8187b_rx_hdr *hdr =
357 (typeof(hdr))(skb_tail_pointer(skb) - sizeof(*hdr));
358 /* The Realtek datasheet for the RTL8187B shows that the RX
359 * header contains the following quantities: signal quality,
360 * RSSI, AGC, the received power in dB, and the measured SNR.
361 * In testing, none of these quantities show qualitative
362 * agreement with AP signal strength, except for the AGC,
363 * which is inversely proportional to the strength of the
364 * signal. In the following, the signal strength
365 * is derived from the AGC. The arbitrary scaling constants
366 * are chosen to make the results close to the values obtained
367 * for a BCM4312 using b43 as the driver. The noise is ignored
368 * for now.
369 */
370 flags = le32_to_cpu(hdr->flags);
371 signal = 14 - hdr->agc / 2;
372 rx_status.antenna = (hdr->rssi >> 7) & 1;
373 rx_status.mactime = le64_to_cpu(hdr->mac_time);
374 }
375
376 rx_status.signal = signal;
377 priv->signal = signal;
378 rate = (flags >> 20) & 0xF;
379 skb_trim(skb, flags & 0x0FFF);
380 rx_status.rate_idx = rate;
381 rx_status.freq = dev->conf.chandef.chan->center_freq;
382 rx_status.band = dev->conf.chandef.chan->band;
383 rx_status.flag |= RX_FLAG_MACTIME_START;
384 if (flags & RTL818X_RX_DESC_FLAG_CRC32_ERR)
385 rx_status.flag |= RX_FLAG_FAILED_FCS_CRC;
386 memcpy(IEEE80211_SKB_RXCB(skb), &rx_status, sizeof(rx_status));
387 ieee80211_rx_irqsafe(dev, skb);
388
389 skb = dev_alloc_skb(RTL8187_MAX_RX);
390 if (unlikely(!skb)) {
391 /* TODO check rx queue length and refill *somewhere* */
392 return;
393 }
394
395 info = (struct rtl8187_rx_info *)skb->cb;
396 info->urb = urb;
397 info->dev = dev;
398 urb->transfer_buffer = skb_tail_pointer(skb);
399 urb->context = skb;
400 skb_queue_tail(&priv->rx_queue, skb);
401
402 usb_anchor_urb(urb, &priv->anchored);
403 if (usb_submit_urb(urb, GFP_ATOMIC)) {
404 usb_unanchor_urb(urb);
405 skb_unlink(skb, &priv->rx_queue);
406 dev_kfree_skb_irq(skb);
407 }
408 }
409
410 static int rtl8187_init_urbs(struct ieee80211_hw *dev)
411 {
412 struct rtl8187_priv *priv = dev->priv;
413 struct urb *entry = NULL;
414 struct sk_buff *skb;
415 struct rtl8187_rx_info *info;
416 int ret = 0;
417
418 while (skb_queue_len(&priv->rx_queue) < 32) {
419 skb = __dev_alloc_skb(RTL8187_MAX_RX, GFP_KERNEL);
420 if (!skb) {
421 ret = -ENOMEM;
422 goto err;
423 }
424 entry = usb_alloc_urb(0, GFP_KERNEL);
425 if (!entry) {
426 ret = -ENOMEM;
427 goto err;
428 }
429 usb_fill_bulk_urb(entry, priv->udev,
430 usb_rcvbulkpipe(priv->udev,
431 priv->is_rtl8187b ? 3 : 1),
432 skb_tail_pointer(skb),
433 RTL8187_MAX_RX, rtl8187_rx_cb, skb);
434 info = (struct rtl8187_rx_info *)skb->cb;
435 info->urb = entry;
436 info->dev = dev;
437 skb_queue_tail(&priv->rx_queue, skb);
438 usb_anchor_urb(entry, &priv->anchored);
439 ret = usb_submit_urb(entry, GFP_KERNEL);
440 usb_put_urb(entry);
441 if (ret) {
442 skb_unlink(skb, &priv->rx_queue);
443 usb_unanchor_urb(entry);
444 goto err;
445 }
446 }
447 return ret;
448
449 err:
450 kfree_skb(skb);
451 usb_kill_anchored_urbs(&priv->anchored);
452 return ret;
453 }
454
455 static void rtl8187b_status_cb(struct urb *urb)
456 {
457 struct ieee80211_hw *hw = (struct ieee80211_hw *)urb->context;
458 struct rtl8187_priv *priv = hw->priv;
459 u64 val;
460 unsigned int cmd_type;
461
462 if (unlikely(urb->status))
463 return;
464
465 /*
466 * Read from status buffer:
467 *
468 * bits [30:31] = cmd type:
469 * - 0 indicates tx beacon interrupt
470 * - 1 indicates tx close descriptor
471 *
472 * In the case of tx beacon interrupt:
473 * [0:9] = Last Beacon CW
474 * [10:29] = reserved
475 * [30:31] = 00b
476 * [32:63] = Last Beacon TSF
477 *
478 * If it's tx close descriptor:
479 * [0:7] = Packet Retry Count
480 * [8:14] = RTS Retry Count
481 * [15] = TOK
482 * [16:27] = Sequence No
483 * [28] = LS
484 * [29] = FS
485 * [30:31] = 01b
486 * [32:47] = unused (reserved?)
487 * [48:63] = MAC Used Time
488 */
489 val = le64_to_cpu(priv->b_tx_status.buf);
490
491 cmd_type = (val >> 30) & 0x3;
492 if (cmd_type == 1) {
493 unsigned int pkt_rc, seq_no;
494 bool tok;
495 struct sk_buff *skb;
496 struct ieee80211_hdr *ieee80211hdr;
497 unsigned long flags;
498
499 pkt_rc = val & 0xFF;
500 tok = val & (1 << 15);
501 seq_no = (val >> 16) & 0xFFF;
502
503 spin_lock_irqsave(&priv->b_tx_status.queue.lock, flags);
504 skb_queue_reverse_walk(&priv->b_tx_status.queue, skb) {
505 ieee80211hdr = (struct ieee80211_hdr *)skb->data;
506
507 /*
508 * While testing, it was discovered that the seq_no
509 * doesn't actually contains the sequence number.
510 * Instead of returning just the 12 bits of sequence
511 * number, hardware is returning entire sequence control
512 * (fragment number plus sequence number) in a 12 bit
513 * only field overflowing after some time. As a
514 * workaround, just consider the lower bits, and expect
515 * it's unlikely we wrongly ack some sent data
516 */
517 if ((le16_to_cpu(ieee80211hdr->seq_ctrl)
518 & 0xFFF) == seq_no)
519 break;
520 }
521 if (skb != (struct sk_buff *) &priv->b_tx_status.queue) {
522 struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
523
524 __skb_unlink(skb, &priv->b_tx_status.queue);
525 if (tok)
526 info->flags |= IEEE80211_TX_STAT_ACK;
527 info->status.rates[0].count = pkt_rc + 1;
528
529 ieee80211_tx_status_irqsafe(hw, skb);
530 }
531 spin_unlock_irqrestore(&priv->b_tx_status.queue.lock, flags);
532 }
533
534 usb_anchor_urb(urb, &priv->anchored);
535 if (usb_submit_urb(urb, GFP_ATOMIC))
536 usb_unanchor_urb(urb);
537 }
538
539 static int rtl8187b_init_status_urb(struct ieee80211_hw *dev)
540 {
541 struct rtl8187_priv *priv = dev->priv;
542 struct urb *entry;
543 int ret = 0;
544
545 entry = usb_alloc_urb(0, GFP_KERNEL);
546 if (!entry)
547 return -ENOMEM;
548
549 usb_fill_bulk_urb(entry, priv->udev, usb_rcvbulkpipe(priv->udev, 9),
550 &priv->b_tx_status.buf, sizeof(priv->b_tx_status.buf),
551 rtl8187b_status_cb, dev);
552
553 usb_anchor_urb(entry, &priv->anchored);
554 ret = usb_submit_urb(entry, GFP_KERNEL);
555 if (ret)
556 usb_unanchor_urb(entry);
557 usb_free_urb(entry);
558
559 return ret;
560 }
561
562 static void rtl8187_set_anaparam(struct rtl8187_priv *priv, bool rfon)
563 {
564 u32 anaparam, anaparam2;
565 u8 anaparam3, reg;
566
567 if (!priv->is_rtl8187b) {
568 if (rfon) {
569 anaparam = RTL8187_RTL8225_ANAPARAM_ON;
570 anaparam2 = RTL8187_RTL8225_ANAPARAM2_ON;
571 } else {
572 anaparam = RTL8187_RTL8225_ANAPARAM_OFF;
573 anaparam2 = RTL8187_RTL8225_ANAPARAM2_OFF;
574 }
575 } else {
576 if (rfon) {
577 anaparam = RTL8187B_RTL8225_ANAPARAM_ON;
578 anaparam2 = RTL8187B_RTL8225_ANAPARAM2_ON;
579 anaparam3 = RTL8187B_RTL8225_ANAPARAM3_ON;
580 } else {
581 anaparam = RTL8187B_RTL8225_ANAPARAM_OFF;
582 anaparam2 = RTL8187B_RTL8225_ANAPARAM2_OFF;
583 anaparam3 = RTL8187B_RTL8225_ANAPARAM3_OFF;
584 }
585 }
586
587 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
588 RTL818X_EEPROM_CMD_CONFIG);
589 reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
590 reg |= RTL818X_CONFIG3_ANAPARAM_WRITE;
591 rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg);
592 rtl818x_iowrite32(priv, &priv->map->ANAPARAM, anaparam);
593 rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, anaparam2);
594 if (priv->is_rtl8187b)
595 rtl818x_iowrite8(priv, &priv->map->ANAPARAM3, anaparam3);
596 reg &= ~RTL818X_CONFIG3_ANAPARAM_WRITE;
597 rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg);
598 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
599 RTL818X_EEPROM_CMD_NORMAL);
600 }
601
602 static int rtl8187_cmd_reset(struct ieee80211_hw *dev)
603 {
604 struct rtl8187_priv *priv = dev->priv;
605 u8 reg;
606 int i;
607
608 reg = rtl818x_ioread8(priv, &priv->map->CMD);
609 reg &= (1 << 1);
610 reg |= RTL818X_CMD_RESET;
611 rtl818x_iowrite8(priv, &priv->map->CMD, reg);
612
613 i = 10;
614 do {
615 msleep(2);
616 if (!(rtl818x_ioread8(priv, &priv->map->CMD) &
617 RTL818X_CMD_RESET))
618 break;
619 } while (--i);
620
621 if (!i) {
622 wiphy_err(dev->wiphy, "Reset timeout!\n");
623 return -ETIMEDOUT;
624 }
625
626 /* reload registers from eeprom */
627 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_LOAD);
628
629 i = 10;
630 do {
631 msleep(4);
632 if (!(rtl818x_ioread8(priv, &priv->map->EEPROM_CMD) &
633 RTL818X_EEPROM_CMD_CONFIG))
634 break;
635 } while (--i);
636
637 if (!i) {
638 wiphy_err(dev->wiphy, "eeprom reset timeout!\n");
639 return -ETIMEDOUT;
640 }
641
642 return 0;
643 }
644
645 static int rtl8187_init_hw(struct ieee80211_hw *dev)
646 {
647 struct rtl8187_priv *priv = dev->priv;
648 u8 reg;
649 int res;
650
651 /* reset */
652 rtl8187_set_anaparam(priv, true);
653
654 rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0);
655
656 msleep(200);
657 rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x10);
658 rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x11);
659 rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x00);
660 msleep(200);
661
662 res = rtl8187_cmd_reset(dev);
663 if (res)
664 return res;
665
666 rtl8187_set_anaparam(priv, true);
667
668 /* setup card */
669 rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0);
670 rtl818x_iowrite8(priv, &priv->map->GPIO0, 0);
671
672 rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, (4 << 8));
673 rtl818x_iowrite8(priv, &priv->map->GPIO0, 1);
674 rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0);
675
676 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
677
678 rtl818x_iowrite16(priv, (__le16 *)0xFFF4, 0xFFFF);
679 reg = rtl818x_ioread8(priv, &priv->map->CONFIG1);
680 reg &= 0x3F;
681 reg |= 0x80;
682 rtl818x_iowrite8(priv, &priv->map->CONFIG1, reg);
683
684 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
685
686 rtl818x_iowrite32(priv, &priv->map->INT_TIMEOUT, 0);
687 rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0);
688 rtl818x_iowrite8(priv, &priv->map->RATE_FALLBACK, 0);
689
690 // TODO: set RESP_RATE and BRSR properly
691 rtl818x_iowrite8(priv, &priv->map->RESP_RATE, (8 << 4) | 0);
692 rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3);
693
694 /* host_usb_init */
695 rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0);
696 rtl818x_iowrite8(priv, &priv->map->GPIO0, 0);
697 reg = rtl818x_ioread8(priv, (u8 *)0xFE53);
698 rtl818x_iowrite8(priv, (u8 *)0xFE53, reg | (1 << 7));
699 rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, (4 << 8));
700 rtl818x_iowrite8(priv, &priv->map->GPIO0, 0x20);
701 rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0);
702 rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x80);
703 rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x80);
704 rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x80);
705 msleep(100);
706
707 rtl818x_iowrite32(priv, &priv->map->RF_TIMING, 0x000a8008);
708 rtl818x_iowrite16(priv, &priv->map->BRSR, 0xFFFF);
709 rtl818x_iowrite32(priv, &priv->map->RF_PARA, 0x00100044);
710 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
711 RTL818X_EEPROM_CMD_CONFIG);
712 rtl818x_iowrite8(priv, &priv->map->CONFIG3, 0x44);
713 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
714 RTL818X_EEPROM_CMD_NORMAL);
715 rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FF7);
716 msleep(100);
717
718 priv->rf->init(dev);
719
720 rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3);
721 reg = rtl818x_ioread8(priv, &priv->map->PGSELECT) & ~1;
722 rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg | 1);
723 rtl818x_iowrite16(priv, (__le16 *)0xFFFE, 0x10);
724 rtl818x_iowrite8(priv, &priv->map->TALLY_SEL, 0x80);
725 rtl818x_iowrite8(priv, (u8 *)0xFFFF, 0x60);
726 rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg);
727
728 return 0;
729 }
730
731 static const u8 rtl8187b_reg_table[][3] = {
732 {0xF0, 0x32, 0}, {0xF1, 0x32, 0}, {0xF2, 0x00, 0}, {0xF3, 0x00, 0},
733 {0xF4, 0x32, 0}, {0xF5, 0x43, 0}, {0xF6, 0x00, 0}, {0xF7, 0x00, 0},
734 {0xF8, 0x46, 0}, {0xF9, 0xA4, 0}, {0xFA, 0x00, 0}, {0xFB, 0x00, 0},
735 {0xFC, 0x96, 0}, {0xFD, 0xA4, 0}, {0xFE, 0x00, 0}, {0xFF, 0x00, 0},
736
737 {0x58, 0x4B, 1}, {0x59, 0x00, 1}, {0x5A, 0x4B, 1}, {0x5B, 0x00, 1},
738 {0x60, 0x4B, 1}, {0x61, 0x09, 1}, {0x62, 0x4B, 1}, {0x63, 0x09, 1},
739 {0xCE, 0x0F, 1}, {0xCF, 0x00, 1}, {0xF0, 0x4E, 1}, {0xF1, 0x01, 1},
740 {0xF2, 0x02, 1}, {0xF3, 0x03, 1}, {0xF4, 0x04, 1}, {0xF5, 0x05, 1},
741 {0xF6, 0x06, 1}, {0xF7, 0x07, 1}, {0xF8, 0x08, 1},
742
743 {0x4E, 0x00, 2}, {0x0C, 0x04, 2}, {0x21, 0x61, 2}, {0x22, 0x68, 2},
744 {0x23, 0x6F, 2}, {0x24, 0x76, 2}, {0x25, 0x7D, 2}, {0x26, 0x84, 2},
745 {0x27, 0x8D, 2}, {0x4D, 0x08, 2}, {0x50, 0x05, 2}, {0x51, 0xF5, 2},
746 {0x52, 0x04, 2}, {0x53, 0xA0, 2}, {0x54, 0x1F, 2}, {0x55, 0x23, 2},
747 {0x56, 0x45, 2}, {0x57, 0x67, 2}, {0x58, 0x08, 2}, {0x59, 0x08, 2},
748 {0x5A, 0x08, 2}, {0x5B, 0x08, 2}, {0x60, 0x08, 2}, {0x61, 0x08, 2},
749 {0x62, 0x08, 2}, {0x63, 0x08, 2}, {0x64, 0xCF, 2},
750
751 {0x5B, 0x40, 0}, {0x84, 0x88, 0}, {0x85, 0x24, 0}, {0x88, 0x54, 0},
752 {0x8B, 0xB8, 0}, {0x8C, 0x07, 0}, {0x8D, 0x00, 0}, {0x94, 0x1B, 0},
753 {0x95, 0x12, 0}, {0x96, 0x00, 0}, {0x97, 0x06, 0}, {0x9D, 0x1A, 0},
754 {0x9F, 0x10, 0}, {0xB4, 0x22, 0}, {0xBE, 0x80, 0}, {0xDB, 0x00, 0},
755 {0xEE, 0x00, 0}, {0x4C, 0x00, 2},
756
757 {0x9F, 0x00, 3}, {0x8C, 0x01, 0}, {0x8D, 0x10, 0}, {0x8E, 0x08, 0},
758 {0x8F, 0x00, 0}
759 };
760
761 static int rtl8187b_init_hw(struct ieee80211_hw *dev)
762 {
763 struct rtl8187_priv *priv = dev->priv;
764 int res, i;
765 u8 reg;
766
767 rtl8187_set_anaparam(priv, true);
768
769 /* Reset PLL sequence on 8187B. Realtek note: reduces power
770 * consumption about 30 mA */
771 rtl818x_iowrite8(priv, (u8 *)0xFF61, 0x10);
772 reg = rtl818x_ioread8(priv, (u8 *)0xFF62);
773 rtl818x_iowrite8(priv, (u8 *)0xFF62, reg & ~(1 << 5));
774 rtl818x_iowrite8(priv, (u8 *)0xFF62, reg | (1 << 5));
775
776 res = rtl8187_cmd_reset(dev);
777 if (res)
778 return res;
779
780 rtl8187_set_anaparam(priv, true);
781
782 /* BRSR (Basic Rate Set Register) on 8187B looks to be the same as
783 * RESP_RATE on 8187L in Realtek sources: each bit should be each
784 * one of the 12 rates, all are enabled */
785 rtl818x_iowrite16(priv, (__le16 *)0xFF34, 0x0FFF);
786
787 reg = rtl818x_ioread8(priv, &priv->map->CW_CONF);
788 reg |= RTL818X_CW_CONF_PERPACKET_RETRY;
789 rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg);
790
791 /* Auto Rate Fallback Register (ARFR): 1M-54M setting */
792 rtl818x_iowrite16_idx(priv, (__le16 *)0xFFE0, 0x0FFF, 1);
793 rtl818x_iowrite8_idx(priv, (u8 *)0xFFE2, 0x00, 1);
794
795 rtl818x_iowrite16_idx(priv, (__le16 *)0xFFD4, 0xFFFF, 1);
796
797 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
798 RTL818X_EEPROM_CMD_CONFIG);
799 reg = rtl818x_ioread8(priv, &priv->map->CONFIG1);
800 rtl818x_iowrite8(priv, &priv->map->CONFIG1, (reg & 0x3F) | 0x80);
801 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
802 RTL818X_EEPROM_CMD_NORMAL);
803
804 rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0);
805 for (i = 0; i < ARRAY_SIZE(rtl8187b_reg_table); i++) {
806 rtl818x_iowrite8_idx(priv,
807 (u8 *)(uintptr_t)
808 (rtl8187b_reg_table[i][0] | 0xFF00),
809 rtl8187b_reg_table[i][1],
810 rtl8187b_reg_table[i][2]);
811 }
812
813 rtl818x_iowrite16(priv, &priv->map->TID_AC_MAP, 0xFA50);
814 rtl818x_iowrite16(priv, &priv->map->INT_MIG, 0);
815
816 rtl818x_iowrite32_idx(priv, (__le32 *)0xFFF0, 0, 1);
817 rtl818x_iowrite32_idx(priv, (__le32 *)0xFFF4, 0, 1);
818 rtl818x_iowrite8_idx(priv, (u8 *)0xFFF8, 0, 1);
819
820 rtl818x_iowrite32(priv, &priv->map->RF_TIMING, 0x00004001);
821
822 /* RFSW_CTRL register */
823 rtl818x_iowrite16_idx(priv, (__le16 *)0xFF72, 0x569A, 2);
824
825 rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x0480);
826 rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x2488);
827 rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FFF);
828 msleep(100);
829
830 priv->rf->init(dev);
831
832 reg = RTL818X_CMD_TX_ENABLE | RTL818X_CMD_RX_ENABLE;
833 rtl818x_iowrite8(priv, &priv->map->CMD, reg);
834 rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF);
835
836 rtl818x_iowrite8(priv, (u8 *)0xFE41, 0xF4);
837 rtl818x_iowrite8(priv, (u8 *)0xFE40, 0x00);
838 rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x00);
839 rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x01);
840 rtl818x_iowrite8(priv, (u8 *)0xFE40, 0x0F);
841 rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x00);
842 rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x01);
843
844 reg = rtl818x_ioread8(priv, (u8 *)0xFFDB);
845 rtl818x_iowrite8(priv, (u8 *)0xFFDB, reg | (1 << 2));
846 rtl818x_iowrite16_idx(priv, (__le16 *)0xFF72, 0x59FA, 3);
847 rtl818x_iowrite16_idx(priv, (__le16 *)0xFF74, 0x59D2, 3);
848 rtl818x_iowrite16_idx(priv, (__le16 *)0xFF76, 0x59D2, 3);
849 rtl818x_iowrite16_idx(priv, (__le16 *)0xFF78, 0x19FA, 3);
850 rtl818x_iowrite16_idx(priv, (__le16 *)0xFF7A, 0x19FA, 3);
851 rtl818x_iowrite16_idx(priv, (__le16 *)0xFF7C, 0x00D0, 3);
852 rtl818x_iowrite8(priv, (u8 *)0xFF61, 0);
853 rtl818x_iowrite8_idx(priv, (u8 *)0xFF80, 0x0F, 1);
854 rtl818x_iowrite8_idx(priv, (u8 *)0xFF83, 0x03, 1);
855 rtl818x_iowrite8(priv, (u8 *)0xFFDA, 0x10);
856 rtl818x_iowrite8_idx(priv, (u8 *)0xFF4D, 0x08, 2);
857
858 rtl818x_iowrite32(priv, &priv->map->HSSI_PARA, 0x0600321B);
859
860 rtl818x_iowrite16_idx(priv, (__le16 *)0xFFEC, 0x0800, 1);
861
862 priv->slot_time = 0x9;
863 priv->aifsn[0] = 2; /* AIFSN[AC_VO] */
864 priv->aifsn[1] = 2; /* AIFSN[AC_VI] */
865 priv->aifsn[2] = 7; /* AIFSN[AC_BK] */
866 priv->aifsn[3] = 3; /* AIFSN[AC_BE] */
867 rtl818x_iowrite8(priv, &priv->map->ACM_CONTROL, 0);
868
869 /* ENEDCA flag must always be set, transmit issues? */
870 rtl818x_iowrite8(priv, &priv->map->MSR, RTL818X_MSR_ENEDCA);
871
872 return 0;
873 }
874
875 static void rtl8187_work(struct work_struct *work)
876 {
877 /* The RTL8187 returns the retry count through register 0xFFFA. In
878 * addition, it appears to be a cumulative retry count, not the
879 * value for the current TX packet. When multiple TX entries are
880 * waiting in the queue, the retry count will be the total for all.
881 * The "error" may matter for purposes of rate setting, but there is
882 * no other choice with this hardware.
883 */
884 struct rtl8187_priv *priv = container_of(work, struct rtl8187_priv,
885 work.work);
886 struct ieee80211_tx_info *info;
887 struct ieee80211_hw *dev = priv->dev;
888 static u16 retry;
889 u16 tmp;
890 u16 avg_retry;
891 int length;
892
893 mutex_lock(&priv->conf_mutex);
894 tmp = rtl818x_ioread16(priv, (__le16 *)0xFFFA);
895 length = skb_queue_len(&priv->b_tx_status.queue);
896 if (unlikely(!length))
897 length = 1;
898 if (unlikely(tmp < retry))
899 tmp = retry;
900 avg_retry = (tmp - retry) / length;
901 while (skb_queue_len(&priv->b_tx_status.queue) > 0) {
902 struct sk_buff *old_skb;
903
904 old_skb = skb_dequeue(&priv->b_tx_status.queue);
905 info = IEEE80211_SKB_CB(old_skb);
906 info->status.rates[0].count = avg_retry + 1;
907 if (info->status.rates[0].count > RETRY_COUNT)
908 info->flags &= ~IEEE80211_TX_STAT_ACK;
909 ieee80211_tx_status_irqsafe(dev, old_skb);
910 }
911 retry = tmp;
912 mutex_unlock(&priv->conf_mutex);
913 }
914
915 static int rtl8187_start(struct ieee80211_hw *dev)
916 {
917 struct rtl8187_priv *priv = dev->priv;
918 u32 reg;
919 int ret;
920
921 mutex_lock(&priv->conf_mutex);
922
923 ret = (!priv->is_rtl8187b) ? rtl8187_init_hw(dev) :
924 rtl8187b_init_hw(dev);
925 if (ret)
926 goto rtl8187_start_exit;
927
928 init_usb_anchor(&priv->anchored);
929 priv->dev = dev;
930
931 if (priv->is_rtl8187b) {
932 reg = RTL818X_RX_CONF_MGMT |
933 RTL818X_RX_CONF_DATA |
934 RTL818X_RX_CONF_BROADCAST |
935 RTL818X_RX_CONF_NICMAC |
936 RTL818X_RX_CONF_BSSID |
937 (7 << 13 /* RX FIFO threshold NONE */) |
938 (7 << 10 /* MAX RX DMA */) |
939 RTL818X_RX_CONF_RX_AUTORESETPHY |
940 RTL818X_RX_CONF_ONLYERLPKT |
941 RTL818X_RX_CONF_MULTICAST;
942 priv->rx_conf = reg;
943 rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg);
944
945 reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL);
946 reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_GAIN;
947 reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL;
948 reg &= ~RTL818X_TX_AGC_CTL_FEEDBACK_ANT;
949 rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg);
950
951 rtl818x_iowrite32(priv, &priv->map->TX_CONF,
952 RTL818X_TX_CONF_HW_SEQNUM |
953 RTL818X_TX_CONF_DISREQQSIZE |
954 (RETRY_COUNT << 8 /* short retry limit */) |
955 (RETRY_COUNT << 0 /* long retry limit */) |
956 (7 << 21 /* MAX TX DMA */));
957 ret = rtl8187_init_urbs(dev);
958 if (ret)
959 goto rtl8187_start_exit;
960 ret = rtl8187b_init_status_urb(dev);
961 if (ret)
962 usb_kill_anchored_urbs(&priv->anchored);
963 goto rtl8187_start_exit;
964 }
965
966 rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF);
967
968 rtl818x_iowrite32(priv, &priv->map->MAR[0], ~0);
969 rtl818x_iowrite32(priv, &priv->map->MAR[1], ~0);
970
971 ret = rtl8187_init_urbs(dev);
972 if (ret)
973 goto rtl8187_start_exit;
974
975 reg = RTL818X_RX_CONF_ONLYERLPKT |
976 RTL818X_RX_CONF_RX_AUTORESETPHY |
977 RTL818X_RX_CONF_BSSID |
978 RTL818X_RX_CONF_MGMT |
979 RTL818X_RX_CONF_DATA |
980 (7 << 13 /* RX FIFO threshold NONE */) |
981 (7 << 10 /* MAX RX DMA */) |
982 RTL818X_RX_CONF_BROADCAST |
983 RTL818X_RX_CONF_NICMAC;
984
985 priv->rx_conf = reg;
986 rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg);
987
988 reg = rtl818x_ioread8(priv, &priv->map->CW_CONF);
989 reg &= ~RTL818X_CW_CONF_PERPACKET_CW;
990 reg |= RTL818X_CW_CONF_PERPACKET_RETRY;
991 rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg);
992
993 reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL);
994 reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_GAIN;
995 reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL;
996 reg &= ~RTL818X_TX_AGC_CTL_FEEDBACK_ANT;
997 rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg);
998
999 reg = RTL818X_TX_CONF_CW_MIN |
1000 (7 << 21 /* MAX TX DMA */) |
1001 RTL818X_TX_CONF_NO_ICV;
1002 rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg);
1003
1004 reg = rtl818x_ioread8(priv, &priv->map->CMD);
1005 reg |= RTL818X_CMD_TX_ENABLE;
1006 reg |= RTL818X_CMD_RX_ENABLE;
1007 rtl818x_iowrite8(priv, &priv->map->CMD, reg);
1008 INIT_DELAYED_WORK(&priv->work, rtl8187_work);
1009
1010 rtl8187_start_exit:
1011 mutex_unlock(&priv->conf_mutex);
1012 return ret;
1013 }
1014
1015 static void rtl8187_stop(struct ieee80211_hw *dev)
1016 {
1017 struct rtl8187_priv *priv = dev->priv;
1018 struct sk_buff *skb;
1019 u32 reg;
1020
1021 mutex_lock(&priv->conf_mutex);
1022 rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0);
1023
1024 reg = rtl818x_ioread8(priv, &priv->map->CMD);
1025 reg &= ~RTL818X_CMD_TX_ENABLE;
1026 reg &= ~RTL818X_CMD_RX_ENABLE;
1027 rtl818x_iowrite8(priv, &priv->map->CMD, reg);
1028
1029 priv->rf->stop(dev);
1030 rtl8187_set_anaparam(priv, false);
1031
1032 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
1033 reg = rtl818x_ioread8(priv, &priv->map->CONFIG4);
1034 rtl818x_iowrite8(priv, &priv->map->CONFIG4, reg | RTL818X_CONFIG4_VCOOFF);
1035 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
1036
1037 while ((skb = skb_dequeue(&priv->b_tx_status.queue)))
1038 dev_kfree_skb_any(skb);
1039
1040 usb_kill_anchored_urbs(&priv->anchored);
1041 mutex_unlock(&priv->conf_mutex);
1042
1043 if (!priv->is_rtl8187b)
1044 cancel_delayed_work_sync(&priv->work);
1045 }
1046
1047 static u64 rtl8187_get_tsf(struct ieee80211_hw *dev, struct ieee80211_vif *vif)
1048 {
1049 struct rtl8187_priv *priv = dev->priv;
1050
1051 return rtl818x_ioread32(priv, &priv->map->TSFT[0]) |
1052 (u64)(rtl818x_ioread32(priv, &priv->map->TSFT[1])) << 32;
1053 }
1054
1055
1056 static void rtl8187_beacon_work(struct work_struct *work)
1057 {
1058 struct rtl8187_vif *vif_priv =
1059 container_of(work, struct rtl8187_vif, beacon_work.work);
1060 struct ieee80211_vif *vif =
1061 container_of((void *)vif_priv, struct ieee80211_vif, drv_priv);
1062 struct ieee80211_hw *dev = vif_priv->dev;
1063 struct ieee80211_mgmt *mgmt;
1064 struct sk_buff *skb;
1065
1066 /* don't overflow the tx ring */
1067 if (ieee80211_queue_stopped(dev, 0))
1068 goto resched;
1069
1070 /* grab a fresh beacon */
1071 skb = ieee80211_beacon_get(dev, vif);
1072 if (!skb)
1073 goto resched;
1074
1075 /*
1076 * update beacon timestamp w/ TSF value
1077 * TODO: make hardware update beacon timestamp
1078 */
1079 mgmt = (struct ieee80211_mgmt *)skb->data;
1080 mgmt->u.beacon.timestamp = cpu_to_le64(rtl8187_get_tsf(dev, vif));
1081
1082 /* TODO: use actual beacon queue */
1083 skb_set_queue_mapping(skb, 0);
1084
1085 rtl8187_tx(dev, NULL, skb);
1086
1087 resched:
1088 /*
1089 * schedule next beacon
1090 * TODO: use hardware support for beacon timing
1091 */
1092 schedule_delayed_work(&vif_priv->beacon_work,
1093 usecs_to_jiffies(1024 * vif->bss_conf.beacon_int));
1094 }
1095
1096
1097 static int rtl8187_add_interface(struct ieee80211_hw *dev,
1098 struct ieee80211_vif *vif)
1099 {
1100 struct rtl8187_priv *priv = dev->priv;
1101 struct rtl8187_vif *vif_priv;
1102 int i;
1103 int ret = -EOPNOTSUPP;
1104
1105 mutex_lock(&priv->conf_mutex);
1106 if (priv->vif)
1107 goto exit;
1108
1109 switch (vif->type) {
1110 case NL80211_IFTYPE_STATION:
1111 case NL80211_IFTYPE_ADHOC:
1112 break;
1113 default:
1114 goto exit;
1115 }
1116
1117 ret = 0;
1118 priv->vif = vif;
1119
1120 /* Initialize driver private area */
1121 vif_priv = (struct rtl8187_vif *)&vif->drv_priv;
1122 vif_priv->dev = dev;
1123 INIT_DELAYED_WORK(&vif_priv->beacon_work, rtl8187_beacon_work);
1124 vif_priv->enable_beacon = false;
1125
1126
1127 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
1128 for (i = 0; i < ETH_ALEN; i++)
1129 rtl818x_iowrite8(priv, &priv->map->MAC[i],
1130 ((u8 *)vif->addr)[i]);
1131 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
1132
1133 exit:
1134 mutex_unlock(&priv->conf_mutex);
1135 return ret;
1136 }
1137
1138 static void rtl8187_remove_interface(struct ieee80211_hw *dev,
1139 struct ieee80211_vif *vif)
1140 {
1141 struct rtl8187_priv *priv = dev->priv;
1142 mutex_lock(&priv->conf_mutex);
1143 priv->vif = NULL;
1144 mutex_unlock(&priv->conf_mutex);
1145 }
1146
1147 static int rtl8187_config(struct ieee80211_hw *dev, u32 changed)
1148 {
1149 struct rtl8187_priv *priv = dev->priv;
1150 struct ieee80211_conf *conf = &dev->conf;
1151 u32 reg;
1152
1153 mutex_lock(&priv->conf_mutex);
1154 reg = rtl818x_ioread32(priv, &priv->map->TX_CONF);
1155 /* Enable TX loopback on MAC level to avoid TX during channel
1156 * changes, as this has be seen to causes problems and the
1157 * card will stop work until next reset
1158 */
1159 rtl818x_iowrite32(priv, &priv->map->TX_CONF,
1160 reg | RTL818X_TX_CONF_LOOPBACK_MAC);
1161 priv->rf->set_chan(dev, conf);
1162 msleep(10);
1163 rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg);
1164
1165 rtl818x_iowrite16(priv, &priv->map->ATIM_WND, 2);
1166 rtl818x_iowrite16(priv, &priv->map->ATIMTR_INTERVAL, 100);
1167 rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL, 100);
1168 rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL_TIME, 100);
1169 mutex_unlock(&priv->conf_mutex);
1170 return 0;
1171 }
1172
1173 /*
1174 * With 8187B, AC_*_PARAM clashes with FEMR definition in struct rtl818x_csr for
1175 * example. Thus we have to use raw values for AC_*_PARAM register addresses.
1176 */
1177 static __le32 *rtl8187b_ac_addr[4] = {
1178 (__le32 *) 0xFFF0, /* AC_VO */
1179 (__le32 *) 0xFFF4, /* AC_VI */
1180 (__le32 *) 0xFFFC, /* AC_BK */
1181 (__le32 *) 0xFFF8, /* AC_BE */
1182 };
1183
1184 #define SIFS_TIME 0xa
1185
1186 static void rtl8187_conf_erp(struct rtl8187_priv *priv, bool use_short_slot,
1187 bool use_short_preamble)
1188 {
1189 if (priv->is_rtl8187b) {
1190 u8 difs, eifs;
1191 u16 ack_timeout;
1192 int queue;
1193
1194 if (use_short_slot) {
1195 priv->slot_time = 0x9;
1196 difs = 0x1c;
1197 eifs = 0x53;
1198 } else {
1199 priv->slot_time = 0x14;
1200 difs = 0x32;
1201 eifs = 0x5b;
1202 }
1203 rtl818x_iowrite8(priv, &priv->map->SIFS, 0x22);
1204 rtl818x_iowrite8(priv, &priv->map->SLOT, priv->slot_time);
1205 rtl818x_iowrite8(priv, &priv->map->DIFS, difs);
1206
1207 /*
1208 * BRSR+1 on 8187B is in fact EIFS register
1209 * Value in units of 4 us
1210 */
1211 rtl818x_iowrite8(priv, (u8 *)&priv->map->BRSR + 1, eifs);
1212
1213 /*
1214 * For 8187B, CARRIER_SENSE_COUNTER is in fact ack timeout
1215 * register. In units of 4 us like eifs register
1216 * ack_timeout = ack duration + plcp + difs + preamble
1217 */
1218 ack_timeout = 112 + 48 + difs;
1219 if (use_short_preamble)
1220 ack_timeout += 72;
1221 else
1222 ack_timeout += 144;
1223 rtl818x_iowrite8(priv, &priv->map->CARRIER_SENSE_COUNTER,
1224 DIV_ROUND_UP(ack_timeout, 4));
1225
1226 for (queue = 0; queue < 4; queue++)
1227 rtl818x_iowrite8(priv, (u8 *) rtl8187b_ac_addr[queue],
1228 priv->aifsn[queue] * priv->slot_time +
1229 SIFS_TIME);
1230 } else {
1231 rtl818x_iowrite8(priv, &priv->map->SIFS, 0x22);
1232 if (use_short_slot) {
1233 rtl818x_iowrite8(priv, &priv->map->SLOT, 0x9);
1234 rtl818x_iowrite8(priv, &priv->map->DIFS, 0x14);
1235 rtl818x_iowrite8(priv, &priv->map->EIFS, 91 - 0x14);
1236 } else {
1237 rtl818x_iowrite8(priv, &priv->map->SLOT, 0x14);
1238 rtl818x_iowrite8(priv, &priv->map->DIFS, 0x24);
1239 rtl818x_iowrite8(priv, &priv->map->EIFS, 91 - 0x24);
1240 }
1241 }
1242 }
1243
1244 static void rtl8187_bss_info_changed(struct ieee80211_hw *dev,
1245 struct ieee80211_vif *vif,
1246 struct ieee80211_bss_conf *info,
1247 u32 changed)
1248 {
1249 struct rtl8187_priv *priv = dev->priv;
1250 struct rtl8187_vif *vif_priv;
1251 int i;
1252 u8 reg;
1253
1254 vif_priv = (struct rtl8187_vif *)&vif->drv_priv;
1255
1256 if (changed & BSS_CHANGED_BSSID) {
1257 mutex_lock(&priv->conf_mutex);
1258 for (i = 0; i < ETH_ALEN; i++)
1259 rtl818x_iowrite8(priv, &priv->map->BSSID[i],
1260 info->bssid[i]);
1261
1262 if (priv->is_rtl8187b)
1263 reg = RTL818X_MSR_ENEDCA;
1264 else
1265 reg = 0;
1266
1267 if (is_valid_ether_addr(info->bssid)) {
1268 if (vif->type == NL80211_IFTYPE_ADHOC)
1269 reg |= RTL818X_MSR_ADHOC;
1270 else
1271 reg |= RTL818X_MSR_INFRA;
1272 }
1273 else
1274 reg |= RTL818X_MSR_NO_LINK;
1275
1276 rtl818x_iowrite8(priv, &priv->map->MSR, reg);
1277
1278 mutex_unlock(&priv->conf_mutex);
1279 }
1280
1281 if (changed & (BSS_CHANGED_ERP_SLOT | BSS_CHANGED_ERP_PREAMBLE))
1282 rtl8187_conf_erp(priv, info->use_short_slot,
1283 info->use_short_preamble);
1284
1285 if (changed & BSS_CHANGED_BEACON_ENABLED)
1286 vif_priv->enable_beacon = info->enable_beacon;
1287
1288 if (changed & (BSS_CHANGED_BEACON_ENABLED | BSS_CHANGED_BEACON)) {
1289 cancel_delayed_work_sync(&vif_priv->beacon_work);
1290 if (vif_priv->enable_beacon)
1291 schedule_work(&vif_priv->beacon_work.work);
1292 }
1293
1294 }
1295
1296 static u64 rtl8187_prepare_multicast(struct ieee80211_hw *dev,
1297 struct netdev_hw_addr_list *mc_list)
1298 {
1299 return netdev_hw_addr_list_count(mc_list);
1300 }
1301
1302 static void rtl8187_configure_filter(struct ieee80211_hw *dev,
1303 unsigned int changed_flags,
1304 unsigned int *total_flags,
1305 u64 multicast)
1306 {
1307 struct rtl8187_priv *priv = dev->priv;
1308
1309 if (changed_flags & FIF_FCSFAIL)
1310 priv->rx_conf ^= RTL818X_RX_CONF_FCS;
1311 if (changed_flags & FIF_CONTROL)
1312 priv->rx_conf ^= RTL818X_RX_CONF_CTRL;
1313 if (changed_flags & FIF_OTHER_BSS)
1314 priv->rx_conf ^= RTL818X_RX_CONF_MONITOR;
1315 if (*total_flags & FIF_ALLMULTI || multicast > 0)
1316 priv->rx_conf |= RTL818X_RX_CONF_MULTICAST;
1317 else
1318 priv->rx_conf &= ~RTL818X_RX_CONF_MULTICAST;
1319
1320 *total_flags = 0;
1321
1322 if (priv->rx_conf & RTL818X_RX_CONF_FCS)
1323 *total_flags |= FIF_FCSFAIL;
1324 if (priv->rx_conf & RTL818X_RX_CONF_CTRL)
1325 *total_flags |= FIF_CONTROL;
1326 if (priv->rx_conf & RTL818X_RX_CONF_MONITOR)
1327 *total_flags |= FIF_OTHER_BSS;
1328 if (priv->rx_conf & RTL818X_RX_CONF_MULTICAST)
1329 *total_flags |= FIF_ALLMULTI;
1330
1331 rtl818x_iowrite32_async(priv, &priv->map->RX_CONF, priv->rx_conf);
1332 }
1333
1334 static int rtl8187_conf_tx(struct ieee80211_hw *dev,
1335 struct ieee80211_vif *vif, u16 queue,
1336 const struct ieee80211_tx_queue_params *params)
1337 {
1338 struct rtl8187_priv *priv = dev->priv;
1339 u8 cw_min, cw_max;
1340
1341 if (queue > 3)
1342 return -EINVAL;
1343
1344 cw_min = fls(params->cw_min);
1345 cw_max = fls(params->cw_max);
1346
1347 if (priv->is_rtl8187b) {
1348 priv->aifsn[queue] = params->aifs;
1349
1350 /*
1351 * This is the structure of AC_*_PARAM registers in 8187B:
1352 * - TXOP limit field, bit offset = 16
1353 * - ECWmax, bit offset = 12
1354 * - ECWmin, bit offset = 8
1355 * - AIFS, bit offset = 0
1356 */
1357 rtl818x_iowrite32(priv, rtl8187b_ac_addr[queue],
1358 (params->txop << 16) | (cw_max << 12) |
1359 (cw_min << 8) | (params->aifs *
1360 priv->slot_time + SIFS_TIME));
1361 } else {
1362 if (queue != 0)
1363 return -EINVAL;
1364
1365 rtl818x_iowrite8(priv, &priv->map->CW_VAL,
1366 cw_min | (cw_max << 4));
1367 }
1368 return 0;
1369 }
1370
1371
1372 static const struct ieee80211_ops rtl8187_ops = {
1373 .tx = rtl8187_tx,
1374 .start = rtl8187_start,
1375 .stop = rtl8187_stop,
1376 .add_interface = rtl8187_add_interface,
1377 .remove_interface = rtl8187_remove_interface,
1378 .config = rtl8187_config,
1379 .bss_info_changed = rtl8187_bss_info_changed,
1380 .prepare_multicast = rtl8187_prepare_multicast,
1381 .configure_filter = rtl8187_configure_filter,
1382 .conf_tx = rtl8187_conf_tx,
1383 .rfkill_poll = rtl8187_rfkill_poll,
1384 .get_tsf = rtl8187_get_tsf,
1385 };
1386
1387 static void rtl8187_eeprom_register_read(struct eeprom_93cx6 *eeprom)
1388 {
1389 struct ieee80211_hw *dev = eeprom->data;
1390 struct rtl8187_priv *priv = dev->priv;
1391 u8 reg = rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
1392
1393 eeprom->reg_data_in = reg & RTL818X_EEPROM_CMD_WRITE;
1394 eeprom->reg_data_out = reg & RTL818X_EEPROM_CMD_READ;
1395 eeprom->reg_data_clock = reg & RTL818X_EEPROM_CMD_CK;
1396 eeprom->reg_chip_select = reg & RTL818X_EEPROM_CMD_CS;
1397 }
1398
1399 static void rtl8187_eeprom_register_write(struct eeprom_93cx6 *eeprom)
1400 {
1401 struct ieee80211_hw *dev = eeprom->data;
1402 struct rtl8187_priv *priv = dev->priv;
1403 u8 reg = RTL818X_EEPROM_CMD_PROGRAM;
1404
1405 if (eeprom->reg_data_in)
1406 reg |= RTL818X_EEPROM_CMD_WRITE;
1407 if (eeprom->reg_data_out)
1408 reg |= RTL818X_EEPROM_CMD_READ;
1409 if (eeprom->reg_data_clock)
1410 reg |= RTL818X_EEPROM_CMD_CK;
1411 if (eeprom->reg_chip_select)
1412 reg |= RTL818X_EEPROM_CMD_CS;
1413
1414 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, reg);
1415 udelay(10);
1416 }
1417
1418 static int rtl8187_probe(struct usb_interface *intf,
1419 const struct usb_device_id *id)
1420 {
1421 struct usb_device *udev = interface_to_usbdev(intf);
1422 struct ieee80211_hw *dev;
1423 struct rtl8187_priv *priv;
1424 struct eeprom_93cx6 eeprom;
1425 struct ieee80211_channel *channel;
1426 const char *chip_name;
1427 u16 txpwr, reg;
1428 u16 product_id = le16_to_cpu(udev->descriptor.idProduct);
1429 int err, i;
1430 u8 mac_addr[ETH_ALEN];
1431
1432 dev = ieee80211_alloc_hw(sizeof(*priv), &rtl8187_ops);
1433 if (!dev) {
1434 printk(KERN_ERR "rtl8187: ieee80211 alloc failed\n");
1435 return -ENOMEM;
1436 }
1437
1438 priv = dev->priv;
1439 priv->is_rtl8187b = (id->driver_info == DEVICE_RTL8187B);
1440
1441 /* allocate "DMA aware" buffer for register accesses */
1442 priv->io_dmabuf = kmalloc(sizeof(*priv->io_dmabuf), GFP_KERNEL);
1443 if (!priv->io_dmabuf) {
1444 err = -ENOMEM;
1445 goto err_free_dev;
1446 }
1447 mutex_init(&priv->io_mutex);
1448
1449 SET_IEEE80211_DEV(dev, &intf->dev);
1450 usb_set_intfdata(intf, dev);
1451 priv->udev = udev;
1452
1453 usb_get_dev(udev);
1454
1455 skb_queue_head_init(&priv->rx_queue);
1456
1457 BUILD_BUG_ON(sizeof(priv->channels) != sizeof(rtl818x_channels));
1458 BUILD_BUG_ON(sizeof(priv->rates) != sizeof(rtl818x_rates));
1459
1460 memcpy(priv->channels, rtl818x_channels, sizeof(rtl818x_channels));
1461 memcpy(priv->rates, rtl818x_rates, sizeof(rtl818x_rates));
1462 priv->map = (struct rtl818x_csr *)0xFF00;
1463
1464 priv->band.band = IEEE80211_BAND_2GHZ;
1465 priv->band.channels = priv->channels;
1466 priv->band.n_channels = ARRAY_SIZE(rtl818x_channels);
1467 priv->band.bitrates = priv->rates;
1468 priv->band.n_bitrates = ARRAY_SIZE(rtl818x_rates);
1469 dev->wiphy->bands[IEEE80211_BAND_2GHZ] = &priv->band;
1470
1471
1472 dev->flags = IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING |
1473 IEEE80211_HW_SIGNAL_DBM |
1474 IEEE80211_HW_RX_INCLUDES_FCS;
1475 /* Initialize rate-control variables */
1476 dev->max_rates = 1;
1477 dev->max_rate_tries = RETRY_COUNT;
1478
1479 eeprom.data = dev;
1480 eeprom.register_read = rtl8187_eeprom_register_read;
1481 eeprom.register_write = rtl8187_eeprom_register_write;
1482 if (rtl818x_ioread32(priv, &priv->map->RX_CONF) & (1 << 6))
1483 eeprom.width = PCI_EEPROM_WIDTH_93C66;
1484 else
1485 eeprom.width = PCI_EEPROM_WIDTH_93C46;
1486
1487 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
1488 udelay(10);
1489
1490 eeprom_93cx6_multiread(&eeprom, RTL8187_EEPROM_MAC_ADDR,
1491 (__le16 __force *)mac_addr, 3);
1492 if (!is_valid_ether_addr(mac_addr)) {
1493 printk(KERN_WARNING "rtl8187: Invalid hwaddr! Using randomly "
1494 "generated MAC address\n");
1495 eth_random_addr(mac_addr);
1496 }
1497 SET_IEEE80211_PERM_ADDR(dev, mac_addr);
1498
1499 channel = priv->channels;
1500 for (i = 0; i < 3; i++) {
1501 eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_1 + i,
1502 &txpwr);
1503 (*channel++).hw_value = txpwr & 0xFF;
1504 (*channel++).hw_value = txpwr >> 8;
1505 }
1506 for (i = 0; i < 2; i++) {
1507 eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_4 + i,
1508 &txpwr);
1509 (*channel++).hw_value = txpwr & 0xFF;
1510 (*channel++).hw_value = txpwr >> 8;
1511 }
1512
1513 eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_BASE,
1514 &priv->txpwr_base);
1515
1516 reg = rtl818x_ioread8(priv, &priv->map->PGSELECT) & ~1;
1517 rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg | 1);
1518 /* 0 means asic B-cut, we should use SW 3 wire
1519 * bit-by-bit banging for radio. 1 means we can use
1520 * USB specific request to write radio registers */
1521 priv->asic_rev = rtl818x_ioread8(priv, (u8 *)0xFFFE) & 0x3;
1522 rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg);
1523 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
1524
1525 if (!priv->is_rtl8187b) {
1526 u32 reg32;
1527 reg32 = rtl818x_ioread32(priv, &priv->map->TX_CONF);
1528 reg32 &= RTL818X_TX_CONF_HWVER_MASK;
1529 switch (reg32) {
1530 case RTL818X_TX_CONF_R8187vD_B:
1531 /* Some RTL8187B devices have a USB ID of 0x8187
1532 * detect them here */
1533 chip_name = "RTL8187BvB(early)";
1534 priv->is_rtl8187b = 1;
1535 priv->hw_rev = RTL8187BvB;
1536 break;
1537 case RTL818X_TX_CONF_R8187vD:
1538 chip_name = "RTL8187vD";
1539 break;
1540 default:
1541 chip_name = "RTL8187vB (default)";
1542 }
1543 } else {
1544 /*
1545 * Force USB request to write radio registers for 8187B, Realtek
1546 * only uses it in their sources
1547 */
1548 /*if (priv->asic_rev == 0) {
1549 printk(KERN_WARNING "rtl8187: Forcing use of USB "
1550 "requests to write to radio registers\n");
1551 priv->asic_rev = 1;
1552 }*/
1553 switch (rtl818x_ioread8(priv, (u8 *)0xFFE1)) {
1554 case RTL818X_R8187B_B:
1555 chip_name = "RTL8187BvB";
1556 priv->hw_rev = RTL8187BvB;
1557 break;
1558 case RTL818X_R8187B_D:
1559 chip_name = "RTL8187BvD";
1560 priv->hw_rev = RTL8187BvD;
1561 break;
1562 case RTL818X_R8187B_E:
1563 chip_name = "RTL8187BvE";
1564 priv->hw_rev = RTL8187BvE;
1565 break;
1566 default:
1567 chip_name = "RTL8187BvB (default)";
1568 priv->hw_rev = RTL8187BvB;
1569 }
1570 }
1571
1572 if (!priv->is_rtl8187b) {
1573 for (i = 0; i < 2; i++) {
1574 eeprom_93cx6_read(&eeprom,
1575 RTL8187_EEPROM_TXPWR_CHAN_6 + i,
1576 &txpwr);
1577 (*channel++).hw_value = txpwr & 0xFF;
1578 (*channel++).hw_value = txpwr >> 8;
1579 }
1580 } else {
1581 eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_6,
1582 &txpwr);
1583 (*channel++).hw_value = txpwr & 0xFF;
1584
1585 eeprom_93cx6_read(&eeprom, 0x0A, &txpwr);
1586 (*channel++).hw_value = txpwr & 0xFF;
1587
1588 eeprom_93cx6_read(&eeprom, 0x1C, &txpwr);
1589 (*channel++).hw_value = txpwr & 0xFF;
1590 (*channel++).hw_value = txpwr >> 8;
1591 }
1592 /* Handle the differing rfkill GPIO bit in different models */
1593 priv->rfkill_mask = RFKILL_MASK_8187_89_97;
1594 if (product_id == 0x8197 || product_id == 0x8198) {
1595 eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_SELECT_GPIO, &reg);
1596 if (reg & 0xFF00)
1597 priv->rfkill_mask = RFKILL_MASK_8198;
1598 }
1599 dev->vif_data_size = sizeof(struct rtl8187_vif);
1600 dev->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION) |
1601 BIT(NL80211_IFTYPE_ADHOC) ;
1602
1603 if ((id->driver_info == DEVICE_RTL8187) && priv->is_rtl8187b)
1604 printk(KERN_INFO "rtl8187: inconsistency between id with OEM"
1605 " info!\n");
1606
1607 priv->rf = rtl8187_detect_rf(dev);
1608 dev->extra_tx_headroom = (!priv->is_rtl8187b) ?
1609 sizeof(struct rtl8187_tx_hdr) :
1610 sizeof(struct rtl8187b_tx_hdr);
1611 if (!priv->is_rtl8187b)
1612 dev->queues = 1;
1613 else
1614 dev->queues = 4;
1615
1616 err = ieee80211_register_hw(dev);
1617 if (err) {
1618 printk(KERN_ERR "rtl8187: Cannot register device\n");
1619 goto err_free_dmabuf;
1620 }
1621 mutex_init(&priv->conf_mutex);
1622 skb_queue_head_init(&priv->b_tx_status.queue);
1623
1624 wiphy_info(dev->wiphy, "hwaddr %pM, %s V%d + %s, rfkill mask %d\n",
1625 mac_addr, chip_name, priv->asic_rev, priv->rf->name,
1626 priv->rfkill_mask);
1627
1628 #ifdef CONFIG_RTL8187_LEDS
1629 eeprom_93cx6_read(&eeprom, 0x3F, &reg);
1630 reg &= 0xFF;
1631 rtl8187_leds_init(dev, reg);
1632 #endif
1633 rtl8187_rfkill_init(dev);
1634
1635 return 0;
1636
1637 err_free_dmabuf:
1638 kfree(priv->io_dmabuf);
1639 err_free_dev:
1640 ieee80211_free_hw(dev);
1641 usb_set_intfdata(intf, NULL);
1642 usb_put_dev(udev);
1643 return err;
1644 }
1645
1646 static void rtl8187_disconnect(struct usb_interface *intf)
1647 {
1648 struct ieee80211_hw *dev = usb_get_intfdata(intf);
1649 struct rtl8187_priv *priv;
1650
1651 if (!dev)
1652 return;
1653
1654 #ifdef CONFIG_RTL8187_LEDS
1655 rtl8187_leds_exit(dev);
1656 #endif
1657 rtl8187_rfkill_exit(dev);
1658 ieee80211_unregister_hw(dev);
1659
1660 priv = dev->priv;
1661 usb_reset_device(priv->udev);
1662 usb_put_dev(interface_to_usbdev(intf));
1663 kfree(priv->io_dmabuf);
1664 ieee80211_free_hw(dev);
1665 }
1666
1667 static struct usb_driver rtl8187_driver = {
1668 .name = KBUILD_MODNAME,
1669 .id_table = rtl8187_table,
1670 .probe = rtl8187_probe,
1671 .disconnect = rtl8187_disconnect,
1672 .disable_hub_initiated_lpm = 1,
1673 };
1674
1675 module_usb_driver(rtl8187_driver);
Linux kernel - Deliverables
This page took 0.070158 seconds and 5 git commands to generate.