drivers/net/wireless/ti/wl1251/boot.c

   1 /*
   2  * This file is part of wl1251
   3  *
   4  * Copyright (C) 2008 Nokia Corporation
   5  *
   6  * This program is free software; you can redistribute it and/or
   7  * modify it under the terms of the GNU General Public License
   8  * version 2 as published by the Free Software Foundation.
   9  *
  10  * This program is distributed in the hope that it will be useful, but
  11  * WITHOUT ANY WARRANTY; without even the implied warranty of
  12  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
  13  * General Public License for more details.
  14  *
  15  * You should have received a copy of the GNU General Public License
  16  * along with this program; if not, write to the Free Software
  17  * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
  18  * 02110-1301 USA
  19  *
  20  */
  21
  22 #include <linux/slab.h>
  23
  24 #include "reg.h"
  25 #include "boot.h"
  26 #include "io.h"
  27 #include "spi.h"
  28 #include "event.h"
  29 #include "acx.h"
  30
  31 void wl1251_boot_target_enable_interrupts(struct wl1251 *wl)
  32 {
  33         wl1251_reg_write32(wl, ACX_REG_INTERRUPT_MASK, ~(wl->intr_mask));
  34         wl1251_reg_write32(wl, HI_CFG, HI_CFG_DEF_VAL);
  35 }
  36
  37 int wl1251_boot_soft_reset(struct wl1251 *wl)
  38 {
  39         unsigned long timeout;
  40         u32 boot_data;
  41
  42         /* perform soft reset */
  43         wl1251_reg_write32(wl, ACX_REG_SLV_SOFT_RESET, ACX_SLV_SOFT_RESET_BIT);
  44
  45         /* SOFT_RESET is self clearing */
  46         timeout = jiffies + usecs_to_jiffies(SOFT_RESET_MAX_TIME);
  47         while (1) {
  48                 boot_data = wl1251_reg_read32(wl, ACX_REG_SLV_SOFT_RESET);
  49                 wl1251_debug(DEBUG_BOOT, "soft reset bootdata 0x%x", boot_data);
  50                 if ((boot_data & ACX_SLV_SOFT_RESET_BIT) == 0)
  51                         break;
  52
  53                 if (time_after(jiffies, timeout)) {
  54                         /* 1.2 check pWhalBus->uSelfClearTime if the
  55                          * timeout was reached */
  56                         wl1251_error("soft reset timeout");
  57                         return -1;
  58                 }
  59
  60                 udelay(SOFT_RESET_STALL_TIME);
  61         }
  62
  63         /* disable Rx/Tx */
  64         wl1251_reg_write32(wl, ENABLE, 0x0);
  65
  66         /* disable auto calibration on start*/
  67         wl1251_reg_write32(wl, SPARE_A2, 0xffff);
  68
  69         return 0;
  70 }
  71
  72 int wl1251_boot_init_seq(struct wl1251 *wl)
  73 {
  74         u32 scr_pad6, init_data, tmp, elp_cmd, ref_freq;
  75
  76         /*
  77          * col #1: INTEGER_DIVIDER
  78          * col #2: FRACTIONAL_DIVIDER
  79          * col #3: ATTN_BB
  80          * col #4: ALPHA_BB
  81          * col #5: STOP_TIME_BB
  82          * col #6: BB_PLL_LOOP_FILTER
  83          */
  84         static const u32 LUT[REF_FREQ_NUM][LUT_PARAM_NUM] = {
  85
  86                 {   83, 87381,  0xB, 5, 0xF00,  3}, /* REF_FREQ_19_2*/
  87                 {   61, 141154, 0xB, 5, 0x1450, 2}, /* REF_FREQ_26_0*/
  88                 {   41, 174763, 0xC, 6, 0x2D00, 1}, /* REF_FREQ_38_4*/
  89                 {   40, 0,      0xC, 6, 0x2EE0, 1}, /* REF_FREQ_40_0*/
  90                 {   47, 162280, 0xC, 6, 0x2760, 1}  /* REF_FREQ_33_6        */
  91         };
  92
  93         /* read NVS params */
  94         scr_pad6 = wl1251_reg_read32(wl, SCR_PAD6);
  95         wl1251_debug(DEBUG_BOOT, "scr_pad6 0x%x", scr_pad6);
  96
  97         /* read ELP_CMD */
  98         elp_cmd = wl1251_reg_read32(wl, ELP_CMD);
  99         wl1251_debug(DEBUG_BOOT, "elp_cmd 0x%x", elp_cmd);
 100
 101         /* set the BB calibration time to be 300 usec (PLL_CAL_TIME) */
 102         ref_freq = scr_pad6 & 0x000000FF;
 103         wl1251_debug(DEBUG_BOOT, "ref_freq 0x%x", ref_freq);
 104
 105         wl1251_reg_write32(wl, PLL_CAL_TIME, 0x9);
 106
 107         /*
 108          * PG 1.2: set the clock buffer time to be 210 usec (CLK_BUF_TIME)
 109          */
 110         wl1251_reg_write32(wl, CLK_BUF_TIME, 0x6);
 111
 112         /*
 113          * set the clock detect feature to work in the restart wu procedure
 114          * (ELP_CFG_MODE[14]) and Select the clock source type
 115          * (ELP_CFG_MODE[13:12])
 116          */
 117         tmp = ((scr_pad6 & 0x0000FF00) << 4) | 0x00004000;
 118         wl1251_reg_write32(wl, ELP_CFG_MODE, tmp);
 119
 120         /* PG 1.2: enable the BB PLL fix. Enable the PLL_LIMP_CLK_EN_CMD */
 121         elp_cmd |= 0x00000040;
 122         wl1251_reg_write32(wl, ELP_CMD, elp_cmd);
 123
 124         /* PG 1.2: Set the BB PLL stable time to be 1000usec
 125          * (PLL_STABLE_TIME) */
 126         wl1251_reg_write32(wl, CFG_PLL_SYNC_CNT, 0x20);
 127
 128         /* PG 1.2: read clock request time */
 129         init_data = wl1251_reg_read32(wl, CLK_REQ_TIME);
 130
 131         /*
 132          * PG 1.2: set the clock request time to be ref_clk_settling_time -
 133          * 1ms = 4ms
 134          */
 135         if (init_data > 0x21)
 136                 tmp = init_data - 0x21;
 137         else
 138                 tmp = 0;
 139         wl1251_reg_write32(wl, CLK_REQ_TIME, tmp);
 140
 141         /* set BB PLL configurations in RF AFE */
 142         wl1251_reg_write32(wl, 0x003058cc, 0x4B5);
 143
 144         /* set RF_AFE_REG_5 */
 145         wl1251_reg_write32(wl, 0x003058d4, 0x50);
 146
 147         /* set RF_AFE_CTRL_REG_2 */
 148         wl1251_reg_write32(wl, 0x00305948, 0x11c001);
 149
 150         /*
 151          * change RF PLL and BB PLL divider for VCO clock and adjust VCO
 152          * bais current(RF_AFE_REG_13)
 153          */
 154         wl1251_reg_write32(wl, 0x003058f4, 0x1e);
 155
 156         /* set BB PLL configurations */
 157         tmp = LUT[ref_freq][LUT_PARAM_INTEGER_DIVIDER] | 0x00017000;
 158         wl1251_reg_write32(wl, 0x00305840, tmp);
 159
 160         /* set fractional divider according to Appendix C-BB PLL
 161          * Calculations
 162          */
 163         tmp = LUT[ref_freq][LUT_PARAM_FRACTIONAL_DIVIDER];
 164         wl1251_reg_write32(wl, 0x00305844, tmp);
 165
 166         /* set the initial data for the sigma delta */
 167         wl1251_reg_write32(wl, 0x00305848, 0x3039);
 168
 169         /*
 170          * set the accumulator attenuation value, calibration loop1
 171          * (alpha), calibration loop2 (beta), calibration loop3 (gamma) and
 172          * the VCO gain
 173          */
 174         tmp = (LUT[ref_freq][LUT_PARAM_ATTN_BB] << 16) |
 175                 (LUT[ref_freq][LUT_PARAM_ALPHA_BB] << 12) | 0x1;
 176         wl1251_reg_write32(wl, 0x00305854, tmp);
 177
 178         /*
 179          * set the calibration stop time after holdoff time expires and set
 180          * settling time HOLD_OFF_TIME_BB
 181          */
 182         tmp = LUT[ref_freq][LUT_PARAM_STOP_TIME_BB] | 0x000A0000;
 183         wl1251_reg_write32(wl, 0x00305858, tmp);
 184
 185         /*
 186          * set BB PLL Loop filter capacitor3- BB_C3[2:0] and set BB PLL
 187          * constant leakage current to linearize PFD to 0uA -
 188          * BB_ILOOPF[7:3]
 189          */
 190         tmp = LUT[ref_freq][LUT_PARAM_BB_PLL_LOOP_FILTER] | 0x00000030;
 191         wl1251_reg_write32(wl, 0x003058f8, tmp);
 192
 193         /*
 194          * set regulator output voltage for n divider to
 195          * 1.35-BB_REFDIV[1:0], set charge pump current- BB_CPGAIN[4:2],
 196          * set BB PLL Loop filter capacitor2- BB_C2[7:5], set gain of BB
 197          * PLL auto-call to normal mode- BB_CALGAIN_3DB[8]
 198          */
 199         wl1251_reg_write32(wl, 0x003058f0, 0x29);
 200
 201         /* enable restart wakeup sequence (ELP_CMD[0]) */
 202         wl1251_reg_write32(wl, ELP_CMD, elp_cmd | 0x1);
 203
 204         /* restart sequence completed */
 205         udelay(2000);
 206
 207         return 0;
 208 }
 209
 210 static void wl1251_boot_set_ecpu_ctrl(struct wl1251 *wl, u32 flag)
 211 {
 212         u32 cpu_ctrl;
 213
 214         /* 10.5.0 run the firmware (I) */
 215         cpu_ctrl = wl1251_reg_read32(wl, ACX_REG_ECPU_CONTROL);
 216
 217         /* 10.5.1 run the firmware (II) */
 218         cpu_ctrl &= ~flag;
 219         wl1251_reg_write32(wl, ACX_REG_ECPU_CONTROL, cpu_ctrl);
 220 }
 221
 222 int wl1251_boot_run_firmware(struct wl1251 *wl)
 223 {
 224         int loop, ret;
 225         u32 chip_id, acx_intr;
 226
 227         wl1251_boot_set_ecpu_ctrl(wl, ECPU_CONTROL_HALT);
 228
 229         chip_id = wl1251_reg_read32(wl, CHIP_ID_B);
 230
 231         wl1251_debug(DEBUG_BOOT, "chip id after firmware boot: 0x%x", chip_id);
 232
 233         if (chip_id != wl->chip_id) {
 234                 wl1251_error("chip id doesn't match after firmware boot");
 235                 return -EIO;
 236         }
 237
 238         /* wait for init to complete */
 239         loop = 0;
 240         while (loop++ < INIT_LOOP) {
 241                 udelay(INIT_LOOP_DELAY);
 242                 acx_intr = wl1251_reg_read32(wl, ACX_REG_INTERRUPT_NO_CLEAR);
 243
 244                 if (acx_intr == 0xffffffff) {
 245                         wl1251_error("error reading hardware complete "
 246                                      "init indication");
 247                         return -EIO;
 248                 }
 249                 /* check that ACX_INTR_INIT_COMPLETE is enabled */
 250                 else if (acx_intr & WL1251_ACX_INTR_INIT_COMPLETE) {
 251                         wl1251_reg_write32(wl, ACX_REG_INTERRUPT_ACK,
 252                                            WL1251_ACX_INTR_INIT_COMPLETE);
 253                         break;
 254                 }
 255         }
 256
 257         if (loop > INIT_LOOP) {
 258                 wl1251_error("timeout waiting for the hardware to "
 259                              "complete initialization");
 260                 return -EIO;
 261         }
 262
 263         /* get hardware config command mail box */
 264         wl->cmd_box_addr = wl1251_reg_read32(wl, REG_COMMAND_MAILBOX_PTR);
 265
 266         /* get hardware config event mail box */
 267         wl->event_box_addr = wl1251_reg_read32(wl, REG_EVENT_MAILBOX_PTR);
 268
 269         /* set the working partition to its "running" mode offset */
 270         wl1251_set_partition(wl, WL1251_PART_WORK_MEM_START,
 271                              WL1251_PART_WORK_MEM_SIZE,
 272                              WL1251_PART_WORK_REG_START,
 273                              WL1251_PART_WORK_REG_SIZE);
 274
 275         wl1251_debug(DEBUG_MAILBOX, "cmd_box_addr 0x%x event_box_addr 0x%x",
 276                      wl->cmd_box_addr, wl->event_box_addr);
 277
 278         wl1251_acx_fw_version(wl, wl->fw_ver, sizeof(wl->fw_ver));
 279
 280         /*
 281          * in case of full asynchronous mode the firmware event must be
 282          * ready to receive event from the command mailbox
 283          */
 284
 285         /* enable gpio interrupts */
 286         wl1251_enable_interrupts(wl);
 287
 288         /* Enable target's interrupts */
 289         wl->intr_mask = WL1251_ACX_INTR_RX0_DATA |
 290                 WL1251_ACX_INTR_RX1_DATA |
 291                 WL1251_ACX_INTR_TX_RESULT |
 292                 WL1251_ACX_INTR_EVENT_A |
 293                 WL1251_ACX_INTR_EVENT_B |
 294                 WL1251_ACX_INTR_INIT_COMPLETE;
 295         wl1251_boot_target_enable_interrupts(wl);
 296
 297         wl->event_mask = SCAN_COMPLETE_EVENT_ID | BSS_LOSE_EVENT_ID |
 298                 SYNCHRONIZATION_TIMEOUT_EVENT_ID |
 299                 ROAMING_TRIGGER_LOW_RSSI_EVENT_ID |
 300                 ROAMING_TRIGGER_REGAINED_RSSI_EVENT_ID |
 301                 REGAINED_BSS_EVENT_ID | BT_PTA_SENSE_EVENT_ID |
 302                 BT_PTA_PREDICTION_EVENT_ID | JOIN_EVENT_COMPLETE_ID |
 303                 PS_REPORT_EVENT_ID;
 304
 305         ret = wl1251_event_unmask(wl);
 306         if (ret < 0) {
 307                 wl1251_error("EVENT mask setting failed");
 308                 return ret;
 309         }
 310
 311         wl1251_event_mbox_config(wl);
 312
 313         /* firmware startup completed */
 314         return 0;
 315 }
 316
 317 static int wl1251_boot_upload_firmware(struct wl1251 *wl)
 318 {
 319         int addr, chunk_num, partition_limit;
 320         size_t fw_data_len, len;
 321         u8 *p, *buf;
 322
 323         /* whal_FwCtrl_LoadFwImageSm() */
 324
 325         wl1251_debug(DEBUG_BOOT, "chip id before fw upload: 0x%x",
 326                      wl1251_reg_read32(wl, CHIP_ID_B));
 327
 328         /* 10.0 check firmware length and set partition */
 329         fw_data_len =  (wl->fw[4] << 24) | (wl->fw[5] << 16) |
 330                 (wl->fw[6] << 8) | (wl->fw[7]);
 331
 332         wl1251_debug(DEBUG_BOOT, "fw_data_len %zu chunk_size %d", fw_data_len,
 333                 CHUNK_SIZE);
 334
 335         if ((fw_data_len % 4) != 0) {
 336                 wl1251_error("firmware length not multiple of four");
 337                 return -EIO;
 338         }
 339
 340         buf = kmalloc(CHUNK_SIZE, GFP_KERNEL);
 341         if (!buf) {
 342                 wl1251_error("allocation for firmware upload chunk failed");
 343                 return -ENOMEM;
 344         }
 345
 346         wl1251_set_partition(wl, WL1251_PART_DOWN_MEM_START,
 347                              WL1251_PART_DOWN_MEM_SIZE,
 348                              WL1251_PART_DOWN_REG_START,
 349                              WL1251_PART_DOWN_REG_SIZE);
 350
 351         /* 10.1 set partition limit and chunk num */
 352         chunk_num = 0;
 353         partition_limit = WL1251_PART_DOWN_MEM_SIZE;
 354
 355         while (chunk_num < fw_data_len / CHUNK_SIZE) {
 356                 /* 10.2 update partition, if needed */
 357                 addr = WL1251_PART_DOWN_MEM_START +
 358                         (chunk_num + 2) * CHUNK_SIZE;
 359                 if (addr > partition_limit) {
 360                         addr = WL1251_PART_DOWN_MEM_START +
 361                                 chunk_num * CHUNK_SIZE;
 362                         partition_limit = chunk_num * CHUNK_SIZE +
 363                                 WL1251_PART_DOWN_MEM_SIZE;
 364                         wl1251_set_partition(wl,
 365                                              addr,
 366                                              WL1251_PART_DOWN_MEM_SIZE,
 367                                              WL1251_PART_DOWN_REG_START,
 368                                              WL1251_PART_DOWN_REG_SIZE);
 369                 }
 370
 371                 /* 10.3 upload the chunk */
 372                 addr = WL1251_PART_DOWN_MEM_START + chunk_num * CHUNK_SIZE;
 373                 p = wl->fw + FW_HDR_SIZE + chunk_num * CHUNK_SIZE;
 374                 wl1251_debug(DEBUG_BOOT, "uploading fw chunk 0x%p to 0x%x",
 375                              p, addr);
 376
 377                 /* need to copy the chunk for dma */
 378                 len = CHUNK_SIZE;
 379                 memcpy(buf, p, len);
 380                 wl1251_mem_write(wl, addr, buf, len);
 381
 382                 chunk_num++;
 383         }
 384
 385         /* 10.4 upload the last chunk */
 386         addr = WL1251_PART_DOWN_MEM_START + chunk_num * CHUNK_SIZE;
 387         p = wl->fw + FW_HDR_SIZE + chunk_num * CHUNK_SIZE;
 388
 389         /* need to copy the chunk for dma */
 390         len = fw_data_len % CHUNK_SIZE;
 391         memcpy(buf, p, len);
 392
 393         wl1251_debug(DEBUG_BOOT, "uploading fw last chunk (%zu B) 0x%p to 0x%x",
 394                      len, p, addr);
 395         wl1251_mem_write(wl, addr, buf, len);
 396
 397         kfree(buf);
 398
 399         return 0;
 400 }
 401
 402 static int wl1251_boot_upload_nvs(struct wl1251 *wl)
 403 {
 404         size_t nvs_len, nvs_bytes_written, burst_len;
 405         int nvs_start, i;
 406         u32 dest_addr, val;
 407         u8 *nvs_ptr, *nvs;
 408
 409         nvs = wl->nvs;
 410         if (nvs == NULL)
 411                 return -ENODEV;
 412
 413         nvs_ptr = nvs;
 414
 415         nvs_len = wl->nvs_len;
 416         nvs_start = wl->fw_len;
 417
 418         /*
 419          * Layout before the actual NVS tables:
 420          * 1 byte : burst length.
 421          * 2 bytes: destination address.
 422          * n bytes: data to burst copy.
 423          *
 424          * This is ended by a 0 length, then the NVS tables.
 425          */
 426
 427         while (nvs_ptr[0]) {
 428                 burst_len = nvs_ptr[0];
 429                 dest_addr = (nvs_ptr[1] & 0xfe) | ((u32)(nvs_ptr[2] << 8));
 430
 431                 /* We move our pointer to the data */
 432                 nvs_ptr += 3;
 433
 434                 for (i = 0; i < burst_len; i++) {
 435                         val = (nvs_ptr[0] | (nvs_ptr[1] << 8)
 436                                | (nvs_ptr[2] << 16) | (nvs_ptr[3] << 24));
 437
 438                         wl1251_debug(DEBUG_BOOT,
 439                                      "nvs burst write 0x%x: 0x%x",
 440                                      dest_addr, val);
 441                         wl1251_mem_write32(wl, dest_addr, val);
 442
 443                         nvs_ptr += 4;
 444                         dest_addr += 4;
 445                 }
 446         }
 447
 448         /*
 449          * We've reached the first zero length, the first NVS table
 450          * is 7 bytes further.
 451          */
 452         nvs_ptr += 7;
 453         nvs_len -= nvs_ptr - nvs;
 454         nvs_len = ALIGN(nvs_len, 4);
 455
 456         /* Now we must set the partition correctly */
 457         wl1251_set_partition(wl, nvs_start,
 458                              WL1251_PART_DOWN_MEM_SIZE,
 459                              WL1251_PART_DOWN_REG_START,
 460                              WL1251_PART_DOWN_REG_SIZE);
 461
 462         /* And finally we upload the NVS tables */
 463         nvs_bytes_written = 0;
 464         while (nvs_bytes_written < nvs_len) {
 465                 val = (nvs_ptr[0] | (nvs_ptr[1] << 8)
 466                        | (nvs_ptr[2] << 16) | (nvs_ptr[3] << 24));
 467
 468                 wl1251_debug(DEBUG_BOOT,
 469                              "nvs write table 0x%x: 0x%x",
 470                              nvs_start, val);
 471                 wl1251_mem_write32(wl, nvs_start, val);
 472
 473                 nvs_ptr += 4;
 474                 nvs_bytes_written += 4;
 475                 nvs_start += 4;
 476         }
 477
 478         return 0;
 479 }
 480
 481 int wl1251_boot(struct wl1251 *wl)
 482 {
 483         int ret = 0, minor_minor_e2_ver;
 484         u32 tmp, boot_data;
 485
 486         /* halt embedded ARM CPU while loading firmware */
 487         wl1251_reg_write32(wl, ACX_REG_ECPU_CONTROL, ECPU_CONTROL_HALT);
 488
 489         ret = wl1251_boot_soft_reset(wl);
 490         if (ret < 0)
 491                 goto out;
 492
 493         /* 2. start processing NVS file */
 494         if (wl->use_eeprom) {
 495                 wl1251_reg_write32(wl, ACX_REG_EE_START, START_EEPROM_MGR);
 496                 /* Wait for EEPROM NVS burst read to complete */
 497                 msleep(40);
 498                 wl1251_reg_write32(wl, ACX_EEPROMLESS_IND_REG, USE_EEPROM);
 499         } else {
 500                 ret = wl1251_boot_upload_nvs(wl);
 501                 if (ret < 0)
 502                         goto out;
 503
 504                 /* write firmware's last address (ie. it's length) to
 505                  * ACX_EEPROMLESS_IND_REG */
 506                 wl1251_reg_write32(wl, ACX_EEPROMLESS_IND_REG, wl->fw_len);
 507         }
 508
 509         /* 6. read the EEPROM parameters */
 510         tmp = wl1251_reg_read32(wl, SCR_PAD2);
 511
 512         /* 7. read bootdata */
 513         wl->boot_attr.radio_type = (tmp & 0x0000FF00) >> 8;
 514         wl->boot_attr.major = (tmp & 0x00FF0000) >> 16;
 515         tmp = wl1251_reg_read32(wl, SCR_PAD3);
 516
 517         /* 8. check bootdata and call restart sequence */
 518         wl->boot_attr.minor = (tmp & 0x00FF0000) >> 16;
 519         minor_minor_e2_ver = (tmp & 0xFF000000) >> 24;
 520
 521         wl1251_debug(DEBUG_BOOT, "radioType 0x%x majorE2Ver 0x%x "
 522                      "minorE2Ver 0x%x minor_minor_e2_ver 0x%x",
 523                      wl->boot_attr.radio_type, wl->boot_attr.major,
 524                      wl->boot_attr.minor, minor_minor_e2_ver);
 525
 526         ret = wl1251_boot_init_seq(wl);
 527         if (ret < 0)
 528                 goto out;
 529
 530         /* 9. NVS processing done */
 531         boot_data = wl1251_reg_read32(wl, ACX_REG_ECPU_CONTROL);
 532
 533         wl1251_debug(DEBUG_BOOT, "halt boot_data 0x%x", boot_data);
 534
 535         /* 10. check that ECPU_CONTROL_HALT bits are set in
 536          * pWhalBus->uBootData and start uploading firmware
 537          */
 538         if ((boot_data & ECPU_CONTROL_HALT) == 0) {
 539                 wl1251_error("boot failed, ECPU_CONTROL_HALT not set");
 540                 ret = -EIO;
 541                 goto out;
 542         }
 543
 544         ret = wl1251_boot_upload_firmware(wl);
 545         if (ret < 0)
 546                 goto out;
 547
 548         /* 10.5 start firmware */
 549         ret = wl1251_boot_run_firmware(wl);
 550         if (ret < 0)
 551                 goto out;
 552
 553 out:
 554         return ret;
 555 }