drivers/net/wireless/ti/wl18xx/reg.h

   1 /*
   2  * This file is part of wlcore
   3  *
   4  * Copyright (C) 2011 Texas Instruments Inc.
   5  *
   6  * This program is free software; you can redistribute it and/or
   7  * modify it under the terms of the GNU General Public License
   8  * version 2 as published by the Free Software Foundation.
   9  *
  10  * This program is distributed in the hope that it will be useful, but
  11  * WITHOUT ANY WARRANTY; without even the implied warranty of
  12  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
  13  * General Public License for more details.
  14  *
  15  * You should have received a copy of the GNU General Public License
  16  * along with this program; if not, write to the Free Software
  17  * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
  18  * 02110-1301 USA
  19  *
  20  */
  21
  22 #ifndef __REG_H__
  23 #define __REG_H__
  24
  25 #define WL18XX_REGISTERS_BASE      0x00800000
  26 #define WL18XX_CODE_BASE           0x00000000
  27 #define WL18XX_DATA_BASE           0x00400000
  28 #define WL18XX_DOUBLE_BUFFER_BASE  0x00600000
  29 #define WL18XX_MCU_KEY_SEARCH_BASE 0x00700000
  30 #define WL18XX_PHY_BASE            0x00900000
  31 #define WL18XX_TOP_OCP_BASE        0x00A00000
  32 #define WL18XX_PACKET_RAM_BASE     0x00B00000
  33 #define WL18XX_HOST_BASE           0x00C00000
  34
  35 #define WL18XX_REGISTERS_DOWN_SIZE 0x0000B000
  36
  37 #define WL18XX_REG_BOOT_PART_START 0x00802000
  38 #define WL18XX_REG_BOOT_PART_SIZE  0x00014578
  39
  40 #define WL18XX_PHY_INIT_MEM_ADDR   0x80926000
  41 #define WL18XX_PHY_END_MEM_ADDR    0x8093CA44
  42 #define WL18XX_PHY_INIT_MEM_SIZE \
  43         (WL18XX_PHY_END_MEM_ADDR - WL18XX_PHY_INIT_MEM_ADDR)
  44
  45 #define WL18XX_SDIO_WSPI_BASE           (WL18XX_REGISTERS_BASE)
  46 #define WL18XX_REG_CONFIG_BASE          (WL18XX_REGISTERS_BASE + 0x02000)
  47 #define WL18XX_WGCM_REGS_BASE           (WL18XX_REGISTERS_BASE + 0x03000)
  48 #define WL18XX_ENC_BASE                 (WL18XX_REGISTERS_BASE + 0x04000)
  49 #define WL18XX_INTERRUPT_BASE           (WL18XX_REGISTERS_BASE + 0x05000)
  50 #define WL18XX_UART_BASE                (WL18XX_REGISTERS_BASE + 0x06000)
  51 #define WL18XX_WELP_BASE                (WL18XX_REGISTERS_BASE + 0x07000)
  52 #define WL18XX_TCP_CKSM_BASE            (WL18XX_REGISTERS_BASE + 0x08000)
  53 #define WL18XX_FIFO_BASE                (WL18XX_REGISTERS_BASE + 0x09000)
  54 #define WL18XX_OCP_BRIDGE_BASE          (WL18XX_REGISTERS_BASE + 0x0A000)
  55 #define WL18XX_PMAC_RX_BASE             (WL18XX_REGISTERS_BASE + 0x14800)
  56 #define WL18XX_PMAC_ACM_BASE            (WL18XX_REGISTERS_BASE + 0x14C00)
  57 #define WL18XX_PMAC_TX_BASE             (WL18XX_REGISTERS_BASE + 0x15000)
  58 #define WL18XX_PMAC_CSR_BASE            (WL18XX_REGISTERS_BASE + 0x15400)
  59
  60 #define WL18XX_REG_ECPU_CONTROL         (WL18XX_REGISTERS_BASE + 0x02004)
  61 #define WL18XX_REG_INTERRUPT_NO_CLEAR   (WL18XX_REGISTERS_BASE + 0x050E8)
  62 #define WL18XX_REG_INTERRUPT_ACK        (WL18XX_REGISTERS_BASE + 0x050F0)
  63 #define WL18XX_REG_INTERRUPT_TRIG       (WL18XX_REGISTERS_BASE + 0x5074)
  64 #define WL18XX_REG_INTERRUPT_TRIG_H     (WL18XX_REGISTERS_BASE + 0x5078)
  65 #define WL18XX_REG_INTERRUPT_MASK       (WL18XX_REGISTERS_BASE + 0x0050DC)
  66
  67 #define WL18XX_REG_CHIP_ID_B            (WL18XX_REGISTERS_BASE + 0x01542C)
  68
  69 #define WL18XX_SLV_MEM_DATA             (WL18XX_HOST_BASE + 0x0018)
  70 #define WL18XX_SLV_REG_DATA             (WL18XX_HOST_BASE + 0x0008)
  71
  72 /* Scratch Pad registers*/
  73 #define WL18XX_SCR_PAD0                 (WL18XX_REGISTERS_BASE + 0x0154EC)
  74 #define WL18XX_SCR_PAD1                 (WL18XX_REGISTERS_BASE + 0x0154F0)
  75 #define WL18XX_SCR_PAD2                 (WL18XX_REGISTERS_BASE + 0x0154F4)
  76 #define WL18XX_SCR_PAD3                 (WL18XX_REGISTERS_BASE + 0x0154F8)
  77 #define WL18XX_SCR_PAD4                 (WL18XX_REGISTERS_BASE + 0x0154FC)
  78 #define WL18XX_SCR_PAD4_SET             (WL18XX_REGISTERS_BASE + 0x015504)
  79 #define WL18XX_SCR_PAD4_CLR             (WL18XX_REGISTERS_BASE + 0x015500)
  80 #define WL18XX_SCR_PAD5                 (WL18XX_REGISTERS_BASE + 0x015508)
  81 #define WL18XX_SCR_PAD5_SET             (WL18XX_REGISTERS_BASE + 0x015510)
  82 #define WL18XX_SCR_PAD5_CLR             (WL18XX_REGISTERS_BASE + 0x01550C)
  83 #define WL18XX_SCR_PAD6                 (WL18XX_REGISTERS_BASE + 0x015514)
  84 #define WL18XX_SCR_PAD7                 (WL18XX_REGISTERS_BASE + 0x015518)
  85 #define WL18XX_SCR_PAD8                 (WL18XX_REGISTERS_BASE + 0x01551C)
  86 #define WL18XX_SCR_PAD9                 (WL18XX_REGISTERS_BASE + 0x015520)
  87
  88 /* Spare registers*/
  89 #define WL18XX_SPARE_A1                 (WL18XX_REGISTERS_BASE + 0x002194)
  90 #define WL18XX_SPARE_A2                 (WL18XX_REGISTERS_BASE + 0x002198)
  91 #define WL18XX_SPARE_A3                 (WL18XX_REGISTERS_BASE + 0x00219C)
  92 #define WL18XX_SPARE_A4                 (WL18XX_REGISTERS_BASE + 0x0021A0)
  93 #define WL18XX_SPARE_A5                 (WL18XX_REGISTERS_BASE + 0x0021A4)
  94 #define WL18XX_SPARE_A6                 (WL18XX_REGISTERS_BASE + 0x0021A8)
  95 #define WL18XX_SPARE_A7                 (WL18XX_REGISTERS_BASE + 0x0021AC)
  96 #define WL18XX_SPARE_A8                 (WL18XX_REGISTERS_BASE + 0x0021B0)
  97 #define WL18XX_SPARE_B1                 (WL18XX_REGISTERS_BASE + 0x015524)
  98 #define WL18XX_SPARE_B2                 (WL18XX_REGISTERS_BASE + 0x015528)
  99 #define WL18XX_SPARE_B3                 (WL18XX_REGISTERS_BASE + 0x01552C)
 100 #define WL18XX_SPARE_B4                 (WL18XX_REGISTERS_BASE + 0x015530)
 101 #define WL18XX_SPARE_B5                 (WL18XX_REGISTERS_BASE + 0x015534)
 102 #define WL18XX_SPARE_B6                 (WL18XX_REGISTERS_BASE + 0x015538)
 103 #define WL18XX_SPARE_B7                 (WL18XX_REGISTERS_BASE + 0x01553C)
 104 #define WL18XX_SPARE_B8                 (WL18XX_REGISTERS_BASE + 0x015540)
 105
 106 #define WL18XX_REG_COMMAND_MAILBOX_PTR  (WL18XX_SCR_PAD0)
 107 #define WL18XX_REG_EVENT_MAILBOX_PTR    (WL18XX_SCR_PAD1)
 108 #define WL18XX_EEPROMLESS_IND           (WL18XX_SCR_PAD4)
 109
 110 #define WL18XX_WELP_ARM_COMMAND         (WL18XX_REGISTERS_BASE + 0x7100)
 111 #define WL18XX_ENABLE                   (WL18XX_REGISTERS_BASE + 0x01543C)
 112 #define TOP_FN0_CCCR_REG_32             (WL18XX_TOP_OCP_BASE + 0x64)
 113
 114 /* PRCM registers */
 115 #define PLATFORM_DETECTION              0xA0E3E0
 116 #define OCS_EN                          0xA02080
 117 #define PRIMARY_CLK_DETECT              0xA020A6
 118 #define PLLSH_COEX_PLL_N                0xA02384
 119 #define PLLSH_COEX_PLL_M                0xA02382
 120 #define PLLSH_COEX_PLL_SWALLOW_EN       0xA0238E
 121 #define PLLSH_WL_PLL_SEL                0xA02398
 122
 123 #define PLLSH_WCS_PLL_N                 0xA02362
 124 #define PLLSH_WCS_PLL_M                 0xA02360
 125 #define PLLSH_WCS_PLL_Q_FACTOR_CFG_1    0xA02364
 126 #define PLLSH_WCS_PLL_Q_FACTOR_CFG_2    0xA02366
 127 #define PLLSH_WCS_PLL_P_FACTOR_CFG_1    0xA02368
 128 #define PLLSH_WCS_PLL_P_FACTOR_CFG_2    0xA0236A
 129 #define PLLSH_WCS_PLL_SWALLOW_EN        0xA0236C
 130 #define PLLSH_WL_PLL_EN                 0xA02392
 131
 132 #define PLLSH_WCS_PLL_Q_FACTOR_CFG_1_MASK       0xFFFF
 133 #define PLLSH_WCS_PLL_Q_FACTOR_CFG_2_MASK       0x007F
 134 #define PLLSH_WCS_PLL_P_FACTOR_CFG_1_MASK       0xFFFF
 135 #define PLLSH_WCS_PLL_P_FACTOR_CFG_2_MASK       0x000F
 136
 137 #define PLLSH_WL_PLL_EN_VAL1            0x7
 138 #define PLLSH_WL_PLL_EN_VAL2            0x2
 139 #define PLLSH_COEX_PLL_SWALLOW_EN_VAL1  0x2
 140 #define PLLSH_COEX_PLL_SWALLOW_EN_VAL2  0x11
 141
 142 #define PLLSH_WCS_PLL_SWALLOW_EN_VAL1   0x1
 143 #define PLLSH_WCS_PLL_SWALLOW_EN_VAL2   0x12
 144
 145 #define PLLSH_WL_PLL_SEL_WCS_PLL        0x0
 146 #define PLLSH_WL_PLL_SEL_COEX_PLL       0x1
 147
 148 #define WL18XX_REG_FUSE_DATA_1_3        0xA0260C
 149 #define WL18XX_PG_VER_MASK              0x70
 150 #define WL18XX_PG_VER_OFFSET            4
 151 #define WL18XX_ROM_VER_MASK             0x3e00
 152 #define WL18XX_ROM_VER_OFFSET           9
 153 #define WL18XX_METAL_VER_MASK           0xC
 154 #define WL18XX_METAL_VER_OFFSET         2
 155 #define WL18XX_NEW_METAL_VER_MASK       0x180
 156 #define WL18XX_NEW_METAL_VER_OFFSET     7
 157
 158 #define WL18XX_PACKAGE_TYPE_OFFSET      13
 159 #define WL18XX_PACKAGE_TYPE_WSP         0
 160
 161 #define WL18XX_REG_FUSE_DATA_2_3        0xA02614
 162 #define WL18XX_RDL_VER_MASK             0x1f00
 163 #define WL18XX_RDL_VER_OFFSET           8
 164
 165 #define WL18XX_REG_FUSE_BD_ADDR_1       0xA02602
 166 #define WL18XX_REG_FUSE_BD_ADDR_2       0xA02606
 167
 168 #define WL18XX_CMD_MBOX_ADDRESS         0xB007B4
 169
 170 #define WL18XX_FW_STATUS_ADDR           0x50F8
 171
 172 #define CHIP_ID_185x_PG10              (0x06030101)
 173 #define CHIP_ID_185x_PG20              (0x06030111)
 174
 175 /*
 176  * Host Command Interrupt. Setting this bit masks
 177  * the interrupt that the host issues to inform
 178  * the FW that it has sent a command
 179  * to the Wlan hardware Command Mailbox.
 180  */
 181 #define WL18XX_INTR_TRIG_CMD       BIT(28)
 182
 183 /*
 184  * Host Event Acknowlegde Interrupt. The host
 185  * sets this bit to acknowledge that it received
 186  * the unsolicited information from the event
 187  * mailbox.
 188  */
 189 #define WL18XX_INTR_TRIG_EVENT_ACK BIT(29)
 190
 191 /*
 192  * To boot the firmware in PLT mode we need to write this value in
 193  * SCR_PAD8 before starting.
 194  */
 195 #define WL18XX_SCR_PAD8_PLT     0xBABABEBE
 196
 197 enum {
 198         COMPONENT_NO_SWITCH     = 0x0,
 199         COMPONENT_2_WAY_SWITCH  = 0x1,
 200         COMPONENT_3_WAY_SWITCH  = 0x2,
 201         COMPONENT_MATCHING      = 0x3,
 202 };
 203
 204 enum {
 205         FEM_NONE        = 0x0,
 206         FEM_VENDOR_1    = 0x1,
 207         FEM_VENDOR_2    = 0x2,
 208         FEM_VENDOR_3    = 0x3,
 209 };
 210
 211 enum {
 212         BOARD_TYPE_EVB_18XX     = 0,
 213         BOARD_TYPE_DVP_18XX     = 1,
 214         BOARD_TYPE_HDK_18XX     = 2,
 215         BOARD_TYPE_FPGA_18XX    = 3,
 216         BOARD_TYPE_COM8_18XX    = 4,
 217
 218         NUM_BOARD_TYPES,
 219 };
 220
 221 enum wl18xx_rdl_num {
 222         RDL_NONE        = 0,
 223         RDL_1_HP        = 1,
 224         RDL_2_SP        = 2,
 225         RDL_3_HP        = 3,
 226         RDL_4_SP        = 4,
 227         RDL_5_SP        = 0x11,
 228         RDL_6_SP        = 0x12,
 229         RDL_7_SP        = 0x13,
 230         RDL_8_SP        = 0x14,
 231
 232         _RDL_LAST,
 233         RDL_MAX = _RDL_LAST - 1,
 234 };
 235
 236
 237 /* FPGA_SPARE_1 register - used to change the PHY ATPG clock at boot time */
 238 #define WL18XX_PHY_FPGA_SPARE_1         0x8093CA40
 239
 240 /* command to disable FDSP clock */
 241 #define MEM_FDSP_CLK_120_DISABLE        0x80000000
 242
 243 /* command to set ATPG clock toward FDSP Code RAM rather than its own clock */
 244 #define MEM_FDSP_CODERAM_FUNC_CLK_SEL   0xC0000000
 245
 246 /* command to re-enable FDSP clock */
 247 #define MEM_FDSP_CLK_120_ENABLE         0x40000000
 248
 249 #endif /* __REG_H__ */