drivers/net/wireless/wl12xx/boot.c

   1 /*
   2  * This file is part of wl1271
   3  *
   4  * Copyright (C) 2008-2010 Nokia Corporation
   5  *
   6  * Contact: Luciano Coelho <luciano.coelho@nokia.com>
   7  *
   8  * This program is free software; you can redistribute it and/or
   9  * modify it under the terms of the GNU General Public License
  10  * version 2 as published by the Free Software Foundation.
  11  *
  12  * This program is distributed in the hope that it will be useful, but
  13  * WITHOUT ANY WARRANTY; without even the implied warranty of
  14  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
  15  * General Public License for more details.
  16  *
  17  * You should have received a copy of the GNU General Public License
  18  * along with this program; if not, write to the Free Software
  19  * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
  20  * 02110-1301 USA
  21  *
  22  */
  23
  24 #include <linux/slab.h>
  25 #include <linux/wl12xx.h>
  26 #include <linux/export.h>
  27
  28 #include "debug.h"
  29 #include "acx.h"
  30 #include "reg.h"
  31 #include "boot.h"
  32 #include "io.h"
  33 #include "event.h"
  34 #include "rx.h"
  35
  36 static void wl1271_boot_set_ecpu_ctrl(struct wl1271 *wl, u32 flag)
  37 {
  38         u32 cpu_ctrl;
  39
  40         /* 10.5.0 run the firmware (I) */
  41         cpu_ctrl = wl1271_read32(wl, ACX_REG_ECPU_CONTROL);
  42
  43         /* 10.5.1 run the firmware (II) */
  44         cpu_ctrl |= flag;
  45         wl1271_write32(wl, ACX_REG_ECPU_CONTROL, cpu_ctrl);
  46 }
  47
  48 static unsigned int wl12xx_get_fw_ver_quirks(struct wl1271 *wl)
  49 {
  50         unsigned int quirks = 0;
  51         unsigned int *fw_ver = wl->chip.fw_ver;
  52
  53         /* Only new station firmwares support routing fw logs to the host */
  54         if ((fw_ver[FW_VER_IF_TYPE] == FW_VER_IF_TYPE_STA) &&
  55             (fw_ver[FW_VER_MINOR] < FW_VER_MINOR_FWLOG_STA_MIN))
  56                 quirks |= WL12XX_QUIRK_FWLOG_NOT_IMPLEMENTED;
  57
  58         /* This feature is not yet supported for AP mode */
  59         if (fw_ver[FW_VER_IF_TYPE] == FW_VER_IF_TYPE_AP)
  60                 quirks |= WL12XX_QUIRK_FWLOG_NOT_IMPLEMENTED;
  61
  62         return quirks;
  63 }
  64
  65 static void wl1271_parse_fw_ver(struct wl1271 *wl)
  66 {
  67         int ret;
  68
  69         ret = sscanf(wl->chip.fw_ver_str + 4, "%u.%u.%u.%u.%u",
  70                      &wl->chip.fw_ver[0], &wl->chip.fw_ver[1],
  71                      &wl->chip.fw_ver[2], &wl->chip.fw_ver[3],
  72                      &wl->chip.fw_ver[4]);
  73
  74         if (ret != 5) {
  75                 wl1271_warning("fw version incorrect value");
  76                 memset(wl->chip.fw_ver, 0, sizeof(wl->chip.fw_ver));
  77                 return;
  78         }
  79
  80         /* Check if any quirks are needed with older fw versions */
  81         wl->quirks |= wl12xx_get_fw_ver_quirks(wl);
  82 }
  83
  84 static void wl1271_boot_fw_version(struct wl1271 *wl)
  85 {
  86         struct wl1271_static_data static_data;
  87
  88         wl1271_read(wl, wl->cmd_box_addr, &static_data, sizeof(static_data),
  89                     false);
  90
  91         strncpy(wl->chip.fw_ver_str, static_data.fw_version,
  92                 sizeof(wl->chip.fw_ver_str));
  93
  94         /* make sure the string is NULL-terminated */
  95         wl->chip.fw_ver_str[sizeof(wl->chip.fw_ver_str) - 1] = '\0';
  96
  97         wl1271_parse_fw_ver(wl);
  98 }
  99
 100 static int wl1271_boot_upload_firmware_chunk(struct wl1271 *wl, void *buf,
 101                                              size_t fw_data_len, u32 dest)
 102 {
 103         struct wl1271_partition_set partition;
 104         int addr, chunk_num, partition_limit;
 105         u8 *p, *chunk;
 106
 107         /* whal_FwCtrl_LoadFwImageSm() */
 108
 109         wl1271_debug(DEBUG_BOOT, "starting firmware upload");
 110
 111         wl1271_debug(DEBUG_BOOT, "fw_data_len %zd chunk_size %d",
 112                      fw_data_len, CHUNK_SIZE);
 113
 114         if ((fw_data_len % 4) != 0) {
 115                 wl1271_error("firmware length not multiple of four");
 116                 return -EIO;
 117         }
 118
 119         chunk = kmalloc(CHUNK_SIZE, GFP_KERNEL);
 120         if (!chunk) {
 121                 wl1271_error("allocation for firmware upload chunk failed");
 122                 return -ENOMEM;
 123         }
 124
 125         memcpy(&partition, &wl12xx_part_table[PART_DOWN], sizeof(partition));
 126         partition.mem.start = dest;
 127         wl1271_set_partition(wl, &partition);
 128
 129         /* 10.1 set partition limit and chunk num */
 130         chunk_num = 0;
 131         partition_limit = wl12xx_part_table[PART_DOWN].mem.size;
 132
 133         while (chunk_num < fw_data_len / CHUNK_SIZE) {
 134                 /* 10.2 update partition, if needed */
 135                 addr = dest + (chunk_num + 2) * CHUNK_SIZE;
 136                 if (addr > partition_limit) {
 137                         addr = dest + chunk_num * CHUNK_SIZE;
 138                         partition_limit = chunk_num * CHUNK_SIZE +
 139                                 wl12xx_part_table[PART_DOWN].mem.size;
 140                         partition.mem.start = addr;
 141                         wl1271_set_partition(wl, &partition);
 142                 }
 143
 144                 /* 10.3 upload the chunk */
 145                 addr = dest + chunk_num * CHUNK_SIZE;
 146                 p = buf + chunk_num * CHUNK_SIZE;
 147                 memcpy(chunk, p, CHUNK_SIZE);
 148                 wl1271_debug(DEBUG_BOOT, "uploading fw chunk 0x%p to 0x%x",
 149                              p, addr);
 150                 wl1271_write(wl, addr, chunk, CHUNK_SIZE, false);
 151
 152                 chunk_num++;
 153         }
 154
 155         /* 10.4 upload the last chunk */
 156         addr = dest + chunk_num * CHUNK_SIZE;
 157         p = buf + chunk_num * CHUNK_SIZE;
 158         memcpy(chunk, p, fw_data_len % CHUNK_SIZE);
 159         wl1271_debug(DEBUG_BOOT, "uploading fw last chunk (%zd B) 0x%p to 0x%x",
 160                      fw_data_len % CHUNK_SIZE, p, addr);
 161         wl1271_write(wl, addr, chunk, fw_data_len % CHUNK_SIZE, false);
 162
 163         kfree(chunk);
 164         return 0;
 165 }
 166
 167 static int wl1271_boot_upload_firmware(struct wl1271 *wl)
 168 {
 169         u32 chunks, addr, len;
 170         int ret = 0;
 171         u8 *fw;
 172
 173         fw = wl->fw;
 174         chunks = be32_to_cpup((__be32 *) fw);
 175         fw += sizeof(u32);
 176
 177         wl1271_debug(DEBUG_BOOT, "firmware chunks to be uploaded: %u", chunks);
 178
 179         while (chunks--) {
 180                 addr = be32_to_cpup((__be32 *) fw);
 181                 fw += sizeof(u32);
 182                 len = be32_to_cpup((__be32 *) fw);
 183                 fw += sizeof(u32);
 184
 185                 if (len > 300000) {
 186                         wl1271_info("firmware chunk too long: %u", len);
 187                         return -EINVAL;
 188                 }
 189                 wl1271_debug(DEBUG_BOOT, "chunk %d addr 0x%x len %u",
 190                              chunks, addr, len);
 191                 ret = wl1271_boot_upload_firmware_chunk(wl, fw, len, addr);
 192                 if (ret != 0)
 193                         break;
 194                 fw += len;
 195         }
 196
 197         return ret;
 198 }
 199
 200 static int wl1271_boot_upload_nvs(struct wl1271 *wl)
 201 {
 202         size_t nvs_len, burst_len;
 203         int i;
 204         u32 dest_addr, val;
 205         u8 *nvs_ptr, *nvs_aligned;
 206
 207         if (wl->nvs == NULL)
 208                 return -ENODEV;
 209
 210         if (wl->chip.id == CHIP_ID_1283_PG20) {
 211                 struct wl128x_nvs_file *nvs = (struct wl128x_nvs_file *)wl->nvs;
 212
 213                 if (wl->nvs_len == sizeof(struct wl128x_nvs_file)) {
 214                         if (nvs->general_params.dual_mode_select)
 215                                 wl->enable_11a = true;
 216                 } else {
 217                         wl1271_error("nvs size is not as expected: %zu != %zu",
 218                                      wl->nvs_len,
 219                                      sizeof(struct wl128x_nvs_file));
 220                         kfree(wl->nvs);
 221                         wl->nvs = NULL;
 222                         wl->nvs_len = 0;
 223                         return -EILSEQ;
 224                 }
 225
 226                 /* only the first part of the NVS needs to be uploaded */
 227                 nvs_len = sizeof(nvs->nvs);
 228                 nvs_ptr = (u8 *)nvs->nvs;
 229
 230         } else {
 231                 struct wl1271_nvs_file *nvs =
 232                         (struct wl1271_nvs_file *)wl->nvs;
 233                 /*
 234                  * FIXME: the LEGACY NVS image support (NVS's missing the 5GHz
 235                  * band configurations) can be removed when those NVS files stop
 236                  * floating around.
 237                  */
 238                 if (wl->nvs_len == sizeof(struct wl1271_nvs_file) ||
 239                     wl->nvs_len == WL1271_INI_LEGACY_NVS_FILE_SIZE) {
 240                         if (nvs->general_params.dual_mode_select)
 241                                 wl->enable_11a = true;
 242                 }
 243
 244                 if (wl->nvs_len != sizeof(struct wl1271_nvs_file) &&
 245                     (wl->nvs_len != WL1271_INI_LEGACY_NVS_FILE_SIZE ||
 246                      wl->enable_11a)) {
 247                         wl1271_error("nvs size is not as expected: %zu != %zu",
 248                                 wl->nvs_len, sizeof(struct wl1271_nvs_file));
 249                         kfree(wl->nvs);
 250                         wl->nvs = NULL;
 251                         wl->nvs_len = 0;
 252                         return -EILSEQ;
 253                 }
 254
 255                 /* only the first part of the NVS needs to be uploaded */
 256                 nvs_len = sizeof(nvs->nvs);
 257                 nvs_ptr = (u8 *) nvs->nvs;
 258         }
 259
 260         /* update current MAC address to NVS */
 261         nvs_ptr[11] = wl->addresses[0].addr[0];
 262         nvs_ptr[10] = wl->addresses[0].addr[1];
 263         nvs_ptr[6] = wl->addresses[0].addr[2];
 264         nvs_ptr[5] = wl->addresses[0].addr[3];
 265         nvs_ptr[4] = wl->addresses[0].addr[4];
 266         nvs_ptr[3] = wl->addresses[0].addr[5];
 267
 268         /*
 269          * Layout before the actual NVS tables:
 270          * 1 byte : burst length.
 271          * 2 bytes: destination address.
 272          * n bytes: data to burst copy.
 273          *
 274          * This is ended by a 0 length, then the NVS tables.
 275          */
 276
 277         /* FIXME: Do we need to check here whether the LSB is 1? */
 278         while (nvs_ptr[0]) {
 279                 burst_len = nvs_ptr[0];
 280                 dest_addr = (nvs_ptr[1] & 0xfe) | ((u32)(nvs_ptr[2] << 8));
 281
 282                 /*
 283                  * Due to our new wl1271_translate_reg_addr function,
 284                  * we need to add the REGISTER_BASE to the destination
 285                  */
 286                 dest_addr += REGISTERS_BASE;
 287
 288                 /* We move our pointer to the data */
 289                 nvs_ptr += 3;
 290
 291                 for (i = 0; i < burst_len; i++) {
 292                         if (nvs_ptr + 3 >= (u8 *) wl->nvs + nvs_len)
 293                                 goto out_badnvs;
 294
 295                         val = (nvs_ptr[0] | (nvs_ptr[1] << 8)
 296                                | (nvs_ptr[2] << 16) | (nvs_ptr[3] << 24));
 297
 298                         wl1271_debug(DEBUG_BOOT,
 299                                      "nvs burst write 0x%x: 0x%x",
 300                                      dest_addr, val);
 301                         wl1271_write32(wl, dest_addr, val);
 302
 303                         nvs_ptr += 4;
 304                         dest_addr += 4;
 305                 }
 306
 307                 if (nvs_ptr >= (u8 *) wl->nvs + nvs_len)
 308                         goto out_badnvs;
 309         }
 310
 311         /*
 312          * We've reached the first zero length, the first NVS table
 313          * is located at an aligned offset which is at least 7 bytes further.
 314          * NOTE: The wl->nvs->nvs element must be first, in order to
 315          * simplify the casting, we assume it is at the beginning of
 316          * the wl->nvs structure.
 317          */
 318         nvs_ptr = (u8 *)wl->nvs +
 319                         ALIGN(nvs_ptr - (u8 *)wl->nvs + 7, 4);
 320
 321         if (nvs_ptr >= (u8 *) wl->nvs + nvs_len)
 322                 goto out_badnvs;
 323
 324         nvs_len -= nvs_ptr - (u8 *)wl->nvs;
 325
 326         /* Now we must set the partition correctly */
 327         wl1271_set_partition(wl, &wl12xx_part_table[PART_WORK]);
 328
 329         /* Copy the NVS tables to a new block to ensure alignment */
 330         nvs_aligned = kmemdup(nvs_ptr, nvs_len, GFP_KERNEL);
 331         if (!nvs_aligned)
 332                 return -ENOMEM;
 333
 334         /* And finally we upload the NVS tables */
 335         wl1271_write(wl, CMD_MBOX_ADDRESS, nvs_aligned, nvs_len, false);
 336
 337         kfree(nvs_aligned);
 338         return 0;
 339
 340 out_badnvs:
 341         wl1271_error("nvs data is malformed");
 342         return -EILSEQ;
 343 }
 344
 345 static void wl1271_boot_enable_interrupts(struct wl1271 *wl)
 346 {
 347         wl1271_enable_interrupts(wl);
 348         wl1271_write32(wl, ACX_REG_INTERRUPT_MASK,
 349                        WL1271_ACX_INTR_ALL & ~(WL1271_INTR_MASK));
 350         wl1271_write32(wl, HI_CFG, HI_CFG_DEF_VAL);
 351 }
 352
 353 static int wl1271_boot_soft_reset(struct wl1271 *wl)
 354 {
 355         unsigned long timeout;
 356         u32 boot_data;
 357
 358         /* perform soft reset */
 359         wl1271_write32(wl, ACX_REG_SLV_SOFT_RESET, ACX_SLV_SOFT_RESET_BIT);
 360
 361         /* SOFT_RESET is self clearing */
 362         timeout = jiffies + usecs_to_jiffies(SOFT_RESET_MAX_TIME);
 363         while (1) {
 364                 boot_data = wl1271_read32(wl, ACX_REG_SLV_SOFT_RESET);
 365                 wl1271_debug(DEBUG_BOOT, "soft reset bootdata 0x%x", boot_data);
 366                 if ((boot_data & ACX_SLV_SOFT_RESET_BIT) == 0)
 367                         break;
 368
 369                 if (time_after(jiffies, timeout)) {
 370                         /* 1.2 check pWhalBus->uSelfClearTime if the
 371                          * timeout was reached */
 372                         wl1271_error("soft reset timeout");
 373                         return -1;
 374                 }
 375
 376                 udelay(SOFT_RESET_STALL_TIME);
 377         }
 378
 379         /* disable Rx/Tx */
 380         wl1271_write32(wl, ENABLE, 0x0);
 381
 382         /* disable auto calibration on start*/
 383         wl1271_write32(wl, SPARE_A2, 0xffff);
 384
 385         return 0;
 386 }
 387
 388 static int wl1271_boot_run_firmware(struct wl1271 *wl)
 389 {
 390         int loop, ret;
 391         u32 chip_id, intr;
 392
 393         wl1271_boot_set_ecpu_ctrl(wl, ECPU_CONTROL_HALT);
 394
 395         chip_id = wl1271_read32(wl, CHIP_ID_B);
 396
 397         wl1271_debug(DEBUG_BOOT, "chip id after firmware boot: 0x%x", chip_id);
 398
 399         if (chip_id != wl->chip.id) {
 400                 wl1271_error("chip id doesn't match after firmware boot");
 401                 return -EIO;
 402         }
 403
 404         /* wait for init to complete */
 405         loop = 0;
 406         while (loop++ < INIT_LOOP) {
 407                 udelay(INIT_LOOP_DELAY);
 408                 intr = wl1271_read32(wl, ACX_REG_INTERRUPT_NO_CLEAR);
 409
 410                 if (intr == 0xffffffff) {
 411                         wl1271_error("error reading hardware complete "
 412                                      "init indication");
 413                         return -EIO;
 414                 }
 415                 /* check that ACX_INTR_INIT_COMPLETE is enabled */
 416                 else if (intr & WL1271_ACX_INTR_INIT_COMPLETE) {
 417                         wl1271_write32(wl, ACX_REG_INTERRUPT_ACK,
 418                                        WL1271_ACX_INTR_INIT_COMPLETE);
 419                         break;
 420                 }
 421         }
 422
 423         if (loop > INIT_LOOP) {
 424                 wl1271_error("timeout waiting for the hardware to "
 425                              "complete initialization");
 426                 return -EIO;
 427         }
 428
 429         /* get hardware config command mail box */
 430         wl->cmd_box_addr = wl1271_read32(wl, REG_COMMAND_MAILBOX_PTR);
 431
 432         /* get hardware config event mail box */
 433         wl->event_box_addr = wl1271_read32(wl, REG_EVENT_MAILBOX_PTR);
 434
 435         /* set the working partition to its "running" mode offset */
 436         wl1271_set_partition(wl, &wl12xx_part_table[PART_WORK]);
 437
 438         wl1271_debug(DEBUG_MAILBOX, "cmd_box_addr 0x%x event_box_addr 0x%x",
 439                      wl->cmd_box_addr, wl->event_box_addr);
 440
 441         wl1271_boot_fw_version(wl);
 442
 443         /*
 444          * in case of full asynchronous mode the firmware event must be
 445          * ready to receive event from the command mailbox
 446          */
 447
 448         /* unmask required mbox events  */
 449         wl->event_mask = BSS_LOSE_EVENT_ID |
 450                 SCAN_COMPLETE_EVENT_ID |
 451                 ROLE_STOP_COMPLETE_EVENT_ID |
 452                 RSSI_SNR_TRIGGER_0_EVENT_ID |
 453                 PSPOLL_DELIVERY_FAILURE_EVENT_ID |
 454                 SOFT_GEMINI_SENSE_EVENT_ID |
 455                 PERIODIC_SCAN_REPORT_EVENT_ID |
 456                 PERIODIC_SCAN_COMPLETE_EVENT_ID |
 457                 DUMMY_PACKET_EVENT_ID |
 458                 PEER_REMOVE_COMPLETE_EVENT_ID |
 459                 BA_SESSION_RX_CONSTRAINT_EVENT_ID |
 460                 REMAIN_ON_CHANNEL_COMPLETE_EVENT_ID |
 461                 INACTIVE_STA_EVENT_ID |
 462                 MAX_TX_RETRY_EVENT_ID |
 463                 CHANNEL_SWITCH_COMPLETE_EVENT_ID;
 464
 465         ret = wl1271_event_unmask(wl);
 466         if (ret < 0) {
 467                 wl1271_error("EVENT mask setting failed");
 468                 return ret;
 469         }
 470
 471         wl1271_event_mbox_config(wl);
 472
 473         /* firmware startup completed */
 474         return 0;
 475 }
 476
 477 static int wl1271_boot_write_irq_polarity(struct wl1271 *wl)
 478 {
 479         u32 polarity;
 480
 481         polarity = wl1271_top_reg_read(wl, OCP_REG_POLARITY);
 482
 483         /* We use HIGH polarity, so unset the LOW bit */
 484         polarity &= ~POLARITY_LOW;
 485         wl1271_top_reg_write(wl, OCP_REG_POLARITY, polarity);
 486
 487         return 0;
 488 }
 489
 490 static int wl128x_switch_tcxo_to_fref(struct wl1271 *wl)
 491 {
 492         u16 spare_reg;
 493
 494         /* Mask bits [2] & [8:4] in the sys_clk_cfg register */
 495         spare_reg = wl1271_top_reg_read(wl, WL_SPARE_REG);
 496         if (spare_reg == 0xFFFF)
 497                 return -EFAULT;
 498         spare_reg |= (BIT(3) | BIT(5) | BIT(6));
 499         wl1271_top_reg_write(wl, WL_SPARE_REG, spare_reg);
 500
 501         /* Enable FREF_CLK_REQ & mux MCS and coex PLLs to FREF */
 502         wl1271_top_reg_write(wl, SYS_CLK_CFG_REG,
 503                              WL_CLK_REQ_TYPE_PG2 | MCS_PLL_CLK_SEL_FREF);
 504
 505         /* Delay execution for 15msec, to let the HW settle */
 506         mdelay(15);
 507
 508         return 0;
 509 }
 510
 511 static bool wl128x_is_tcxo_valid(struct wl1271 *wl)
 512 {
 513         u16 tcxo_detection;
 514
 515         tcxo_detection = wl1271_top_reg_read(wl, TCXO_CLK_DETECT_REG);
 516         if (tcxo_detection & TCXO_DET_FAILED)
 517                 return false;
 518
 519         return true;
 520 }
 521
 522 static bool wl128x_is_fref_valid(struct wl1271 *wl)
 523 {
 524         u16 fref_detection;
 525
 526         fref_detection = wl1271_top_reg_read(wl, FREF_CLK_DETECT_REG);
 527         if (fref_detection & FREF_CLK_DETECT_FAIL)
 528                 return false;
 529
 530         return true;
 531 }
 532
 533 static int wl128x_manually_configure_mcs_pll(struct wl1271 *wl)
 534 {
 535         wl1271_top_reg_write(wl, MCS_PLL_M_REG, MCS_PLL_M_REG_VAL);
 536         wl1271_top_reg_write(wl, MCS_PLL_N_REG, MCS_PLL_N_REG_VAL);
 537         wl1271_top_reg_write(wl, MCS_PLL_CONFIG_REG, MCS_PLL_CONFIG_REG_VAL);
 538
 539         return 0;
 540 }
 541
 542 static int wl128x_configure_mcs_pll(struct wl1271 *wl, int clk)
 543 {
 544         u16 spare_reg;
 545         u16 pll_config;
 546         u8 input_freq;
 547
 548         /* Mask bits [3:1] in the sys_clk_cfg register */
 549         spare_reg = wl1271_top_reg_read(wl, WL_SPARE_REG);
 550         if (spare_reg == 0xFFFF)
 551                 return -EFAULT;
 552         spare_reg |= BIT(2);
 553         wl1271_top_reg_write(wl, WL_SPARE_REG, spare_reg);
 554
 555         /* Handle special cases of the TCXO clock */
 556         if (wl->tcxo_clock == WL12XX_TCXOCLOCK_16_8 ||
 557             wl->tcxo_clock == WL12XX_TCXOCLOCK_33_6)
 558                 return wl128x_manually_configure_mcs_pll(wl);
 559
 560         /* Set the input frequency according to the selected clock source */
 561         input_freq = (clk & 1) + 1;
 562
 563         pll_config = wl1271_top_reg_read(wl, MCS_PLL_CONFIG_REG);
 564         if (pll_config == 0xFFFF)
 565                 return -EFAULT;
 566         pll_config |= (input_freq << MCS_SEL_IN_FREQ_SHIFT);
 567         pll_config |= MCS_PLL_ENABLE_HP;
 568         wl1271_top_reg_write(wl, MCS_PLL_CONFIG_REG, pll_config);
 569
 570         return 0;
 571 }
 572
 573 /*
 574  * WL128x has two clocks input - TCXO and FREF.
 575  * TCXO is the main clock of the device, while FREF is used to sync
 576  * between the GPS and the cellular modem.
 577  * In cases where TCXO is 32.736MHz or 16.368MHz, the FREF will be used
 578  * as the WLAN/BT main clock.
 579  */
 580 static int wl128x_boot_clk(struct wl1271 *wl, int *selected_clock)
 581 {
 582         u16 sys_clk_cfg;
 583
 584         /* For XTAL-only modes, FREF will be used after switching from TCXO */
 585         if (wl->ref_clock == WL12XX_REFCLOCK_26_XTAL ||
 586             wl->ref_clock == WL12XX_REFCLOCK_38_XTAL) {
 587                 if (!wl128x_switch_tcxo_to_fref(wl))
 588                         return -EINVAL;
 589                 goto fref_clk;
 590         }
 591
 592         /* Query the HW, to determine which clock source we should use */
 593         sys_clk_cfg = wl1271_top_reg_read(wl, SYS_CLK_CFG_REG);
 594         if (sys_clk_cfg == 0xFFFF)
 595                 return -EINVAL;
 596         if (sys_clk_cfg & PRCM_CM_EN_MUX_WLAN_FREF)
 597                 goto fref_clk;
 598
 599         /* If TCXO is either 32.736MHz or 16.368MHz, switch to FREF */
 600         if (wl->tcxo_clock == WL12XX_TCXOCLOCK_16_368 ||
 601             wl->tcxo_clock == WL12XX_TCXOCLOCK_32_736) {
 602                 if (!wl128x_switch_tcxo_to_fref(wl))
 603                         return -EINVAL;
 604                 goto fref_clk;
 605         }
 606
 607         /* TCXO clock is selected */
 608         if (!wl128x_is_tcxo_valid(wl))
 609                 return -EINVAL;
 610         *selected_clock = wl->tcxo_clock;
 611         goto config_mcs_pll;
 612
 613 fref_clk:
 614         /* FREF clock is selected */
 615         if (!wl128x_is_fref_valid(wl))
 616                 return -EINVAL;
 617         *selected_clock = wl->ref_clock;
 618
 619 config_mcs_pll:
 620         return wl128x_configure_mcs_pll(wl, *selected_clock);
 621 }
 622
 623 static int wl127x_boot_clk(struct wl1271 *wl)
 624 {
 625         u32 pause;
 626         u32 clk;
 627
 628         if (WL127X_PG_GET_MAJOR(wl->hw_pg_ver) < 3)
 629                 wl->quirks |= WL12XX_QUIRK_END_OF_TRANSACTION;
 630
 631         if (wl->ref_clock == CONF_REF_CLK_19_2_E ||
 632             wl->ref_clock == CONF_REF_CLK_38_4_E ||
 633             wl->ref_clock == CONF_REF_CLK_38_4_M_XTAL)
 634                 /* ref clk: 19.2/38.4/38.4-XTAL */
 635                 clk = 0x3;
 636         else if (wl->ref_clock == CONF_REF_CLK_26_E ||
 637                  wl->ref_clock == CONF_REF_CLK_52_E)
 638                 /* ref clk: 26/52 */
 639                 clk = 0x5;
 640         else
 641                 return -EINVAL;
 642
 643         if (wl->ref_clock != CONF_REF_CLK_19_2_E) {
 644                 u16 val;
 645                 /* Set clock type (open drain) */
 646                 val = wl1271_top_reg_read(wl, OCP_REG_CLK_TYPE);
 647                 val &= FREF_CLK_TYPE_BITS;
 648                 wl1271_top_reg_write(wl, OCP_REG_CLK_TYPE, val);
 649
 650                 /* Set clock pull mode (no pull) */
 651                 val = wl1271_top_reg_read(wl, OCP_REG_CLK_PULL);
 652                 val |= NO_PULL;
 653                 wl1271_top_reg_write(wl, OCP_REG_CLK_PULL, val);
 654         } else {
 655                 u16 val;
 656                 /* Set clock polarity */
 657                 val = wl1271_top_reg_read(wl, OCP_REG_CLK_POLARITY);
 658                 val &= FREF_CLK_POLARITY_BITS;
 659                 val |= CLK_REQ_OUTN_SEL;
 660                 wl1271_top_reg_write(wl, OCP_REG_CLK_POLARITY, val);
 661         }
 662
 663         wl1271_write32(wl, PLL_PARAMETERS, clk);
 664
 665         pause = wl1271_read32(wl, PLL_PARAMETERS);
 666
 667         wl1271_debug(DEBUG_BOOT, "pause1 0x%x", pause);
 668
 669         pause &= ~(WU_COUNTER_PAUSE_VAL);
 670         pause |= WU_COUNTER_PAUSE_VAL;
 671         wl1271_write32(wl, WU_COUNTER_PAUSE, pause);
 672
 673         return 0;
 674 }
 675
 676 /* uploads NVS and firmware */
 677 int wl1271_load_firmware(struct wl1271 *wl)
 678 {
 679         int ret = 0;
 680         u32 tmp, clk;
 681         int selected_clock = -1;
 682
 683         if (wl->chip.id == CHIP_ID_1283_PG20) {
 684                 ret = wl128x_boot_clk(wl, &selected_clock);
 685                 if (ret < 0)
 686                         goto out;
 687         } else {
 688                 ret = wl127x_boot_clk(wl);
 689                 if (ret < 0)
 690                         goto out;
 691         }
 692
 693         /* Continue the ELP wake up sequence */
 694         wl1271_write32(wl, WELP_ARM_COMMAND, WELP_ARM_COMMAND_VAL);
 695         udelay(500);
 696
 697         wl1271_set_partition(wl, &wl12xx_part_table[PART_DRPW]);
 698
 699         /* Read-modify-write DRPW_SCRATCH_START register (see next state)
 700            to be used by DRPw FW. The RTRIM value will be added by the FW
 701            before taking DRPw out of reset */
 702
 703         wl1271_debug(DEBUG_BOOT, "DRPW_SCRATCH_START %08x", DRPW_SCRATCH_START);
 704         clk = wl1271_read32(wl, DRPW_SCRATCH_START);
 705
 706         wl1271_debug(DEBUG_BOOT, "clk2 0x%x", clk);
 707
 708         if (wl->chip.id == CHIP_ID_1283_PG20) {
 709                 clk |= ((selected_clock & 0x3) << 1) << 4;
 710         } else {
 711                 clk |= (wl->ref_clock << 1) << 4;
 712         }
 713
 714         wl1271_write32(wl, DRPW_SCRATCH_START, clk);
 715
 716         wl1271_set_partition(wl, &wl12xx_part_table[PART_WORK]);
 717
 718         /* Disable interrupts */
 719         wl1271_write32(wl, ACX_REG_INTERRUPT_MASK, WL1271_ACX_INTR_ALL);
 720
 721         ret = wl1271_boot_soft_reset(wl);
 722         if (ret < 0)
 723                 goto out;
 724
 725         /* 2. start processing NVS file */
 726         ret = wl1271_boot_upload_nvs(wl);
 727         if (ret < 0)
 728                 goto out;
 729
 730         /* write firmware's last address (ie. it's length) to
 731          * ACX_EEPROMLESS_IND_REG */
 732         wl1271_debug(DEBUG_BOOT, "ACX_EEPROMLESS_IND_REG");
 733
 734         wl1271_write32(wl, ACX_EEPROMLESS_IND_REG, ACX_EEPROMLESS_IND_REG);
 735
 736         tmp = wl1271_read32(wl, CHIP_ID_B);
 737
 738         wl1271_debug(DEBUG_BOOT, "chip id 0x%x", tmp);
 739
 740         /* 6. read the EEPROM parameters */
 741         tmp = wl1271_read32(wl, SCR_PAD2);
 742
 743         /* WL1271: The reference driver skips steps 7 to 10 (jumps directly
 744          * to upload_fw) */
 745
 746         if (wl->chip.id == CHIP_ID_1283_PG20)
 747                 wl1271_top_reg_write(wl, SDIO_IO_DS, wl->conf.hci_io_ds);
 748
 749         ret = wl1271_boot_upload_firmware(wl);
 750         if (ret < 0)
 751                 goto out;
 752
 753 out:
 754         return ret;
 755 }
 756 EXPORT_SYMBOL_GPL(wl1271_load_firmware);
 757
 758 int wl1271_boot(struct wl1271 *wl)
 759 {
 760         int ret;
 761
 762         /* upload NVS and firmware */
 763         ret = wl1271_load_firmware(wl);
 764         if (ret)
 765                 return ret;
 766
 767         /* 10.5 start firmware */
 768         ret = wl1271_boot_run_firmware(wl);
 769         if (ret < 0)
 770                 goto out;
 771
 772         ret = wl1271_boot_write_irq_polarity(wl);
 773         if (ret < 0)
 774                 goto out;
 775
 776         wl1271_write32(wl, ACX_REG_INTERRUPT_MASK,
 777                        WL1271_ACX_ALL_EVENTS_VECTOR);
 778
 779         /* Enable firmware interrupts now */
 780         wl1271_boot_enable_interrupts(wl);
 781
 782         wl1271_event_mbox_config(wl);
 783
 784 out:
 785         return ret;
 786 }