2 * ata_piix.c - Intel PATA/SATA controllers
4 * Maintained by: Jeff Garzik <jgarzik@pobox.com>
5 * Please ALWAYS copy linux-ide@vger.kernel.org
9 * Copyright 2003-2005 Red Hat Inc
10 * Copyright 2003-2005 Jeff Garzik
13 * Copyright header from piix.c:
15 * Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
16 * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
17 * Copyright (C) 2003 Red Hat Inc <alan@redhat.com>
20 * This program is free software; you can redistribute it and/or modify
21 * it under the terms of the GNU General Public License as published by
22 * the Free Software Foundation; either version 2, or (at your option)
25 * This program is distributed in the hope that it will be useful,
26 * but WITHOUT ANY WARRANTY; without even the implied warranty of
27 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
28 * GNU General Public License for more details.
30 * You should have received a copy of the GNU General Public License
31 * along with this program; see the file COPYING. If not, write to
32 * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
35 * libata documentation is available via 'make {ps|pdf}docs',
36 * as Documentation/DocBook/libata.*
38 * Hardware documentation available at http://developer.intel.com/
41 * Publically available from Intel web site. Errata documentation
42 * is also publically available. As an aide to anyone hacking on this
43 * driver the list of errata that are relevant is below.going back to
44 * PIIX4. Older device documentation is now a bit tricky to find.
46 * The chipsets all follow very much the same design. The orginal Triton
47 * series chipsets do _not_ support independant device timings, but this
48 * is fixed in Triton II. With the odd mobile exception the chips then
49 * change little except in gaining more modes until SATA arrives. This
50 * driver supports only the chips with independant timing (that is those
51 * with SITRE and the 0x44 timing register). See pata_oldpiix and pata_mpiix
52 * for the early chip drivers.
57 * PIIX4 errata #9 - Only on ultra obscure hw
58 * ICH3 errata #13 - Not observed to affect real hw
61 * Things we must deal with
62 * PIIX4 errata #10 - BM IDE hang with non UDMA
63 * (must stop/start dma to recover)
64 * 440MX errata #15 - As PIIX4 errata #10
65 * PIIX4 errata #15 - Must not read control registers
66 * during a PIO transfer
67 * 440MX errata #13 - As PIIX4 errata #15
68 * ICH2 errata #21 - DMA mode 0 doesn't work right
69 * ICH0/1 errata #55 - As ICH2 errata #21
70 * ICH2 spec c #9 - Extra operations needed to handle
71 * drive hotswap [NOT YET SUPPORTED]
72 * ICH2 spec c #20 - IDE PRD must not cross a 64K boundary
73 * and must be dword aligned
74 * ICH2 spec c #24 - UDMA mode 4,5 t85/86 should be 6ns not 3.3
76 * Should have been BIOS fixed:
77 * 450NX: errata #19 - DMA hangs on old 450NX
78 * 450NX: errata #20 - DMA hangs on old 450NX
79 * 450NX: errata #25 - Corruption with DMA on old 450NX
80 * ICH3 errata #15 - IDE deadlock under high load
81 * (BIOS must set dev 31 fn 0 bit 23)
82 * ICH3 errata #18 - Don't use native mode
85 #include <linux/kernel.h>
86 #include <linux/module.h>
87 #include <linux/pci.h>
88 #include <linux/init.h>
89 #include <linux/blkdev.h>
90 #include <linux/delay.h>
91 #include <linux/device.h>
92 #include <scsi/scsi_host.h>
93 #include <linux/libata.h>
95 #define DRV_NAME "ata_piix"
96 #define DRV_VERSION "2.00"
99 PIIX_IOCFG
= 0x54, /* IDE I/O configuration register */
100 ICH5_PMR
= 0x90, /* port mapping register */
101 ICH5_PCS
= 0x92, /* port control and status */
102 PIIX_SCC
= 0x0A, /* sub-class code register */
104 PIIX_FLAG_IGNORE_PCS
= (1 << 25), /* ignore PCS present bits */
105 PIIX_FLAG_SCR
= (1 << 26), /* SCR available */
106 PIIX_FLAG_AHCI
= (1 << 27), /* AHCI possible */
107 PIIX_FLAG_CHECKINTR
= (1 << 28), /* make sure PCI INTx enabled */
108 PIIX_FLAG_COMBINED
= (1 << 29), /* combined mode possible */
109 /* ICH6/7 use different scheme for map value */
110 PIIX_FLAG_COMBINED_ICH6
= PIIX_FLAG_COMBINED
| (1 << 30),
112 /* combined mode. if set, PATA is channel 0.
113 * if clear, PATA is channel 1.
115 PIIX_PORT_ENABLED
= (1 << 0),
116 PIIX_PORT_PRESENT
= (1 << 4),
118 PIIX_80C_PRI
= (1 << 5) | (1 << 4),
119 PIIX_80C_SEC
= (1 << 7) | (1 << 6),
131 /* constants for mapping table */
137 NA
= -2, /* not avaliable */
138 RV
= -3, /* reserved */
140 PIIX_AHCI_DEVICE
= 6,
145 const u32 port_enable
;
146 const int present_shift
;
150 struct piix_host_priv
{
152 const struct piix_map_db
*map_db
;
155 static int piix_init_one (struct pci_dev
*pdev
,
156 const struct pci_device_id
*ent
);
157 static void piix_host_stop(struct ata_host_set
*host_set
);
158 static void piix_set_piomode (struct ata_port
*ap
, struct ata_device
*adev
);
159 static void piix_set_dmamode (struct ata_port
*ap
, struct ata_device
*adev
);
160 static void piix_pata_error_handler(struct ata_port
*ap
);
161 static void piix_sata_error_handler(struct ata_port
*ap
);
163 static unsigned int in_module_init
= 1;
165 static const struct pci_device_id piix_pci_tbl
[] = {
166 #ifdef ATA_ENABLE_PATA
167 { 0x8086, 0x7111, PCI_ANY_ID
, PCI_ANY_ID
, 0, 0, piix4_pata
},
168 { 0x8086, 0x24db, PCI_ANY_ID
, PCI_ANY_ID
, 0, 0, ich5_pata
},
169 { 0x8086, 0x25a2, PCI_ANY_ID
, PCI_ANY_ID
, 0, 0, ich5_pata
},
170 { 0x8086, 0x27df, PCI_ANY_ID
, PCI_ANY_ID
, 0, 0, ich5_pata
},
173 /* NOTE: The following PCI ids must be kept in sync with the
174 * list in drivers/pci/quirks.c.
178 { 0x8086, 0x24d1, PCI_ANY_ID
, PCI_ANY_ID
, 0, 0, ich5_sata
},
180 { 0x8086, 0x24df, PCI_ANY_ID
, PCI_ANY_ID
, 0, 0, ich5_sata
},
181 /* 6300ESB (ICH5 variant with broken PCS present bits) */
182 { 0x8086, 0x25a3, PCI_ANY_ID
, PCI_ANY_ID
, 0, 0, esb_sata
},
183 /* 6300ESB pretending RAID */
184 { 0x8086, 0x25b0, PCI_ANY_ID
, PCI_ANY_ID
, 0, 0, esb_sata
},
185 /* 82801FB/FW (ICH6/ICH6W) */
186 { 0x8086, 0x2651, PCI_ANY_ID
, PCI_ANY_ID
, 0, 0, ich6_sata
},
187 /* 82801FR/FRW (ICH6R/ICH6RW) */
188 { 0x8086, 0x2652, PCI_ANY_ID
, PCI_ANY_ID
, 0, 0, ich6_sata_ahci
},
189 /* 82801FBM ICH6M (ICH6R with only port 0 and 2 implemented) */
190 { 0x8086, 0x2653, PCI_ANY_ID
, PCI_ANY_ID
, 0, 0, ich6m_sata_ahci
},
191 /* 82801GB/GR/GH (ICH7, identical to ICH6) */
192 { 0x8086, 0x27c0, PCI_ANY_ID
, PCI_ANY_ID
, 0, 0, ich6_sata_ahci
},
193 /* 2801GBM/GHM (ICH7M, identical to ICH6M) */
194 { 0x8086, 0x27c4, PCI_ANY_ID
, PCI_ANY_ID
, 0, 0, ich6m_sata_ahci
},
195 /* Enterprise Southbridge 2 (where's the datasheet?) */
196 { 0x8086, 0x2680, PCI_ANY_ID
, PCI_ANY_ID
, 0, 0, ich6_sata_ahci
},
197 /* SATA Controller 1 IDE (ICH8, no datasheet yet) */
198 { 0x8086, 0x2820, PCI_ANY_ID
, PCI_ANY_ID
, 0, 0, ich8_sata_ahci
},
199 /* SATA Controller 2 IDE (ICH8, ditto) */
200 { 0x8086, 0x2825, PCI_ANY_ID
, PCI_ANY_ID
, 0, 0, ich8_sata_ahci
},
201 /* Mobile SATA Controller IDE (ICH8M, ditto) */
202 { 0x8086, 0x2828, PCI_ANY_ID
, PCI_ANY_ID
, 0, 0, ich8_sata_ahci
},
204 { } /* terminate list */
207 static struct pci_driver piix_pci_driver
= {
209 .id_table
= piix_pci_tbl
,
210 .probe
= piix_init_one
,
211 .remove
= ata_pci_remove_one
,
212 .suspend
= ata_pci_device_suspend
,
213 .resume
= ata_pci_device_resume
,
216 static struct scsi_host_template piix_sht
= {
217 .module
= THIS_MODULE
,
219 .ioctl
= ata_scsi_ioctl
,
220 .queuecommand
= ata_scsi_queuecmd
,
221 .can_queue
= ATA_DEF_QUEUE
,
222 .this_id
= ATA_SHT_THIS_ID
,
223 .sg_tablesize
= LIBATA_MAX_PRD
,
224 .cmd_per_lun
= ATA_SHT_CMD_PER_LUN
,
225 .emulated
= ATA_SHT_EMULATED
,
226 .use_clustering
= ATA_SHT_USE_CLUSTERING
,
227 .proc_name
= DRV_NAME
,
228 .dma_boundary
= ATA_DMA_BOUNDARY
,
229 .slave_configure
= ata_scsi_slave_config
,
230 .slave_destroy
= ata_scsi_slave_destroy
,
231 .bios_param
= ata_std_bios_param
,
232 .resume
= ata_scsi_device_resume
,
233 .suspend
= ata_scsi_device_suspend
,
236 static const struct ata_port_operations piix_pata_ops
= {
237 .port_disable
= ata_port_disable
,
238 .set_piomode
= piix_set_piomode
,
239 .set_dmamode
= piix_set_dmamode
,
240 .mode_filter
= ata_pci_default_filter
,
242 .tf_load
= ata_tf_load
,
243 .tf_read
= ata_tf_read
,
244 .check_status
= ata_check_status
,
245 .exec_command
= ata_exec_command
,
246 .dev_select
= ata_std_dev_select
,
248 .bmdma_setup
= ata_bmdma_setup
,
249 .bmdma_start
= ata_bmdma_start
,
250 .bmdma_stop
= ata_bmdma_stop
,
251 .bmdma_status
= ata_bmdma_status
,
252 .qc_prep
= ata_qc_prep
,
253 .qc_issue
= ata_qc_issue_prot
,
254 .data_xfer
= ata_pio_data_xfer
,
256 .freeze
= ata_bmdma_freeze
,
257 .thaw
= ata_bmdma_thaw
,
258 .error_handler
= piix_pata_error_handler
,
259 .post_internal_cmd
= ata_bmdma_post_internal_cmd
,
261 .irq_handler
= ata_interrupt
,
262 .irq_clear
= ata_bmdma_irq_clear
,
264 .port_start
= ata_port_start
,
265 .port_stop
= ata_port_stop
,
266 .host_stop
= piix_host_stop
,
269 static const struct ata_port_operations piix_sata_ops
= {
270 .port_disable
= ata_port_disable
,
272 .tf_load
= ata_tf_load
,
273 .tf_read
= ata_tf_read
,
274 .check_status
= ata_check_status
,
275 .exec_command
= ata_exec_command
,
276 .dev_select
= ata_std_dev_select
,
278 .bmdma_setup
= ata_bmdma_setup
,
279 .bmdma_start
= ata_bmdma_start
,
280 .bmdma_stop
= ata_bmdma_stop
,
281 .bmdma_status
= ata_bmdma_status
,
282 .qc_prep
= ata_qc_prep
,
283 .qc_issue
= ata_qc_issue_prot
,
284 .data_xfer
= ata_pio_data_xfer
,
286 .freeze
= ata_bmdma_freeze
,
287 .thaw
= ata_bmdma_thaw
,
288 .error_handler
= piix_sata_error_handler
,
289 .post_internal_cmd
= ata_bmdma_post_internal_cmd
,
291 .irq_handler
= ata_interrupt
,
292 .irq_clear
= ata_bmdma_irq_clear
,
294 .port_start
= ata_port_start
,
295 .port_stop
= ata_port_stop
,
296 .host_stop
= piix_host_stop
,
299 static const struct piix_map_db ich5_map_db
= {
304 /* PM PS SM SS MAP */
305 { P0
, NA
, P1
, NA
}, /* 000b */
306 { P1
, NA
, P0
, NA
}, /* 001b */
309 { P0
, P1
, IDE
, IDE
}, /* 100b */
310 { P1
, P0
, IDE
, IDE
}, /* 101b */
311 { IDE
, IDE
, P0
, P1
}, /* 110b */
312 { IDE
, IDE
, P1
, P0
}, /* 111b */
316 static const struct piix_map_db ich6_map_db
= {
321 /* PM PS SM SS MAP */
322 { P0
, P2
, P1
, P3
}, /* 00b */
323 { IDE
, IDE
, P1
, P3
}, /* 01b */
324 { P0
, P2
, IDE
, IDE
}, /* 10b */
329 static const struct piix_map_db ich6m_map_db
= {
334 /* PM PS SM SS MAP */
335 { P0
, P2
, RV
, RV
}, /* 00b */
337 { P0
, P2
, IDE
, IDE
}, /* 10b */
342 static const struct piix_map_db ich8_map_db
= {
347 /* PM PS SM SS MAP */
348 { P0
, RV
, P1
, RV
}, /* 00b (hardwired) */
350 { RV
, RV
, RV
, RV
}, /* 10b (never) */
355 static const struct piix_map_db
*piix_map_db_table
[] = {
356 [ich5_sata
] = &ich5_map_db
,
357 [esb_sata
] = &ich5_map_db
,
358 [ich6_sata
] = &ich6_map_db
,
359 [ich6_sata_ahci
] = &ich6_map_db
,
360 [ich6m_sata_ahci
] = &ich6m_map_db
,
361 [ich8_sata_ahci
] = &ich8_map_db
,
364 static struct ata_port_info piix_port_info
[] = {
368 .host_flags
= ATA_FLAG_SLAVE_POSS
,
369 .pio_mask
= 0x1f, /* pio0-4 */
371 .mwdma_mask
= 0x06, /* mwdma1-2 */
373 .mwdma_mask
= 0x00, /* mwdma broken */
375 .udma_mask
= ATA_UDMA_MASK_40C
,
376 .port_ops
= &piix_pata_ops
,
382 .host_flags
= ATA_FLAG_SLAVE_POSS
| PIIX_FLAG_CHECKINTR
,
383 .pio_mask
= 0x1f, /* pio0-4 */
385 .mwdma_mask
= 0x06, /* mwdma1-2 */
387 .mwdma_mask
= 0x00, /* mwdma broken */
389 .udma_mask
= 0x3f, /* udma0-5 */
390 .port_ops
= &piix_pata_ops
,
396 .host_flags
= ATA_FLAG_SATA
| PIIX_FLAG_COMBINED
|
398 .pio_mask
= 0x1f, /* pio0-4 */
399 .mwdma_mask
= 0x07, /* mwdma0-2 */
400 .udma_mask
= 0x7f, /* udma0-6 */
401 .port_ops
= &piix_sata_ops
,
407 .host_flags
= ATA_FLAG_SATA
| PIIX_FLAG_COMBINED
|
408 PIIX_FLAG_CHECKINTR
| PIIX_FLAG_IGNORE_PCS
,
409 .pio_mask
= 0x1f, /* pio0-4 */
410 .mwdma_mask
= 0x07, /* mwdma0-2 */
411 .udma_mask
= 0x7f, /* udma0-6 */
412 .port_ops
= &piix_sata_ops
,
418 .host_flags
= ATA_FLAG_SATA
| PIIX_FLAG_COMBINED_ICH6
|
419 PIIX_FLAG_CHECKINTR
| PIIX_FLAG_SCR
,
420 .pio_mask
= 0x1f, /* pio0-4 */
421 .mwdma_mask
= 0x07, /* mwdma0-2 */
422 .udma_mask
= 0x7f, /* udma0-6 */
423 .port_ops
= &piix_sata_ops
,
429 .host_flags
= ATA_FLAG_SATA
| PIIX_FLAG_COMBINED_ICH6
|
430 PIIX_FLAG_CHECKINTR
| PIIX_FLAG_SCR
|
432 .pio_mask
= 0x1f, /* pio0-4 */
433 .mwdma_mask
= 0x07, /* mwdma0-2 */
434 .udma_mask
= 0x7f, /* udma0-6 */
435 .port_ops
= &piix_sata_ops
,
438 /* ich6m_sata_ahci */
441 .host_flags
= ATA_FLAG_SATA
| PIIX_FLAG_COMBINED_ICH6
|
442 PIIX_FLAG_CHECKINTR
| PIIX_FLAG_SCR
|
444 .pio_mask
= 0x1f, /* pio0-4 */
445 .mwdma_mask
= 0x07, /* mwdma0-2 */
446 .udma_mask
= 0x7f, /* udma0-6 */
447 .port_ops
= &piix_sata_ops
,
453 .host_flags
= ATA_FLAG_SATA
| PIIX_FLAG_COMBINED_ICH6
|
454 PIIX_FLAG_CHECKINTR
| PIIX_FLAG_SCR
|
456 .pio_mask
= 0x1f, /* pio0-4 */
457 .mwdma_mask
= 0x07, /* mwdma0-2 */
458 .udma_mask
= 0x7f, /* udma0-6 */
459 .port_ops
= &piix_sata_ops
,
463 static struct pci_bits piix_enable_bits
[] = {
464 { 0x41U
, 1U, 0x80UL
, 0x80UL
}, /* port 0 */
465 { 0x43U
, 1U, 0x80UL
, 0x80UL
}, /* port 1 */
468 MODULE_AUTHOR("Andre Hedrick, Alan Cox, Andrzej Krzysztofowicz, Jeff Garzik");
469 MODULE_DESCRIPTION("SCSI low-level driver for Intel PIIX/ICH ATA controllers");
470 MODULE_LICENSE("GPL");
471 MODULE_DEVICE_TABLE(pci
, piix_pci_tbl
);
472 MODULE_VERSION(DRV_VERSION
);
475 * piix_pata_cbl_detect - Probe host controller cable detect info
476 * @ap: Port for which cable detect info is desired
478 * Read 80c cable indicator from ATA PCI device's PCI config
479 * register. This register is normally set by firmware (BIOS).
482 * None (inherited from caller).
484 static void piix_pata_cbl_detect(struct ata_port
*ap
)
486 struct pci_dev
*pdev
= to_pci_dev(ap
->host_set
->dev
);
489 /* no 80c support in host controller? */
490 if ((ap
->udma_mask
& ~ATA_UDMA_MASK_40C
) == 0)
493 /* check BIOS cable detect results */
494 mask
= ap
->hard_port_no
== 0 ? PIIX_80C_PRI
: PIIX_80C_SEC
;
495 pci_read_config_byte(pdev
, PIIX_IOCFG
, &tmp
);
496 if ((tmp
& mask
) == 0)
499 ap
->cbl
= ATA_CBL_PATA80
;
503 ap
->cbl
= ATA_CBL_PATA40
;
504 ap
->udma_mask
&= ATA_UDMA_MASK_40C
;
508 * piix_pata_prereset - prereset for PATA host controller
511 * Prereset including cable detection.
514 * None (inherited from caller).
516 static int piix_pata_prereset(struct ata_port
*ap
)
518 struct pci_dev
*pdev
= to_pci_dev(ap
->host_set
->dev
);
520 if (!pci_test_config_bits(pdev
, &piix_enable_bits
[ap
->hard_port_no
])) {
521 ata_port_printk(ap
, KERN_INFO
, "port disabled. ignoring.\n");
522 ap
->eh_context
.i
.action
&= ~ATA_EH_RESET_MASK
;
526 piix_pata_cbl_detect(ap
);
528 return ata_std_prereset(ap
);
531 static void piix_pata_error_handler(struct ata_port
*ap
)
533 ata_bmdma_drive_eh(ap
, piix_pata_prereset
, ata_std_softreset
, NULL
,
538 * piix_sata_prereset - prereset for SATA host controller
541 * Reads and configures SATA PCI device's PCI config register
542 * Port Configuration and Status (PCS) to determine port and
543 * device availability. Return -ENODEV to skip reset if no
547 * None (inherited from caller).
550 * 0 if device is present, -ENODEV otherwise.
552 static int piix_sata_prereset(struct ata_port
*ap
)
554 struct pci_dev
*pdev
= to_pci_dev(ap
->host_set
->dev
);
555 struct piix_host_priv
*hpriv
= ap
->host_set
->private_data
;
556 const unsigned int *map
= hpriv
->map
;
557 int base
= 2 * ap
->hard_port_no
;
558 unsigned int present
= 0;
562 pci_read_config_word(pdev
, ICH5_PCS
, &pcs
);
563 DPRINTK("ata%u: ENTER, pcs=0x%x base=%d\n", ap
->id
, pcs
, base
);
565 for (i
= 0; i
< 2; i
++) {
566 port
= map
[base
+ i
];
569 if ((ap
->flags
& PIIX_FLAG_IGNORE_PCS
) ||
570 (pcs
& 1 << (hpriv
->map_db
->present_shift
+ port
)))
574 DPRINTK("ata%u: LEAVE, pcs=0x%x present_mask=0x%x\n",
575 ap
->id
, pcs
, present_mask
);
578 ata_port_printk(ap
, KERN_INFO
, "SATA port has no device.\n");
579 ap
->eh_context
.i
.action
&= ~ATA_EH_RESET_MASK
;
583 return ata_std_prereset(ap
);
586 static void piix_sata_error_handler(struct ata_port
*ap
)
588 ata_bmdma_drive_eh(ap
, piix_sata_prereset
, ata_std_softreset
, NULL
,
593 * piix_set_piomode - Initialize host controller PATA PIO timings
594 * @ap: Port whose timings we are configuring
597 * Set PIO mode for device, in host controller PCI config space.
600 * None (inherited from caller).
603 static void piix_set_piomode (struct ata_port
*ap
, struct ata_device
*adev
)
605 unsigned int pio
= adev
->pio_mode
- XFER_PIO_0
;
606 struct pci_dev
*dev
= to_pci_dev(ap
->host_set
->dev
);
607 unsigned int is_slave
= (adev
->devno
!= 0);
608 unsigned int master_port
= ap
->hard_port_no
? 0x42 : 0x40;
609 unsigned int slave_port
= 0x44;
613 static const /* ISP RTC */
614 u8 timings
[][2] = { { 0, 0 },
620 pci_read_config_word(dev
, master_port
, &master_data
);
622 master_data
|= 0x4000;
623 /* enable PPE, IE and TIME */
624 master_data
|= 0x0070;
625 pci_read_config_byte(dev
, slave_port
, &slave_data
);
626 slave_data
&= (ap
->hard_port_no
? 0x0f : 0xf0);
628 (timings
[pio
][0] << 2) |
629 (timings
[pio
][1] << (ap
->hard_port_no
? 4 : 0));
631 master_data
&= 0xccf8;
632 /* enable PPE, IE and TIME */
633 master_data
|= 0x0007;
635 (timings
[pio
][0] << 12) |
636 (timings
[pio
][1] << 8);
638 pci_write_config_word(dev
, master_port
, master_data
);
640 pci_write_config_byte(dev
, slave_port
, slave_data
);
644 * piix_set_dmamode - Initialize host controller PATA PIO timings
645 * @ap: Port whose timings we are configuring
647 * @udma: udma mode, 0 - 6
649 * Set UDMA mode for device, in host controller PCI config space.
652 * None (inherited from caller).
655 static void piix_set_dmamode (struct ata_port
*ap
, struct ata_device
*adev
)
657 unsigned int udma
= adev
->dma_mode
; /* FIXME: MWDMA too */
658 struct pci_dev
*dev
= to_pci_dev(ap
->host_set
->dev
);
659 u8 maslave
= ap
->hard_port_no
? 0x42 : 0x40;
661 unsigned int drive_dn
= (ap
->hard_port_no
? 2 : 0) + adev
->devno
;
662 int a_speed
= 3 << (drive_dn
* 4);
663 int u_flag
= 1 << drive_dn
;
664 int v_flag
= 0x01 << drive_dn
;
665 int w_flag
= 0x10 << drive_dn
;
669 u8 reg48
, reg54
, reg55
;
671 pci_read_config_word(dev
, maslave
, ®4042
);
672 DPRINTK("reg4042 = 0x%04x\n", reg4042
);
673 sitre
= (reg4042
& 0x4000) ? 1 : 0;
674 pci_read_config_byte(dev
, 0x48, ®48
);
675 pci_read_config_word(dev
, 0x4a, ®4a
);
676 pci_read_config_byte(dev
, 0x54, ®54
);
677 pci_read_config_byte(dev
, 0x55, ®55
);
681 case XFER_UDMA_2
: u_speed
= 2 << (drive_dn
* 4); break;
685 case XFER_UDMA_1
: u_speed
= 1 << (drive_dn
* 4); break;
686 case XFER_UDMA_0
: u_speed
= 0 << (drive_dn
* 4); break;
688 case XFER_MW_DMA_1
: break;
694 if (speed
>= XFER_UDMA_0
) {
695 if (!(reg48
& u_flag
))
696 pci_write_config_byte(dev
, 0x48, reg48
| u_flag
);
697 if (speed
== XFER_UDMA_5
) {
698 pci_write_config_byte(dev
, 0x55, (u8
) reg55
|w_flag
);
700 pci_write_config_byte(dev
, 0x55, (u8
) reg55
& ~w_flag
);
702 if ((reg4a
& a_speed
) != u_speed
)
703 pci_write_config_word(dev
, 0x4a, (reg4a
& ~a_speed
) | u_speed
);
704 if (speed
> XFER_UDMA_2
) {
705 if (!(reg54
& v_flag
))
706 pci_write_config_byte(dev
, 0x54, reg54
| v_flag
);
708 pci_write_config_byte(dev
, 0x54, reg54
& ~v_flag
);
711 pci_write_config_byte(dev
, 0x48, reg48
& ~u_flag
);
713 pci_write_config_word(dev
, 0x4a, reg4a
& ~a_speed
);
715 pci_write_config_byte(dev
, 0x54, reg54
& ~v_flag
);
717 pci_write_config_byte(dev
, 0x55, (u8
) reg55
& ~w_flag
);
721 #define AHCI_PCI_BAR 5
722 #define AHCI_GLOBAL_CTL 0x04
723 #define AHCI_ENABLE (1 << 31)
724 static int piix_disable_ahci(struct pci_dev
*pdev
)
730 /* BUG: pci_enable_device has not yet been called. This
731 * works because this device is usually set up by BIOS.
734 if (!pci_resource_start(pdev
, AHCI_PCI_BAR
) ||
735 !pci_resource_len(pdev
, AHCI_PCI_BAR
))
738 mmio
= pci_iomap(pdev
, AHCI_PCI_BAR
, 64);
742 tmp
= readl(mmio
+ AHCI_GLOBAL_CTL
);
743 if (tmp
& AHCI_ENABLE
) {
745 writel(tmp
, mmio
+ AHCI_GLOBAL_CTL
);
747 tmp
= readl(mmio
+ AHCI_GLOBAL_CTL
);
748 if (tmp
& AHCI_ENABLE
)
752 pci_iounmap(pdev
, mmio
);
757 * piix_check_450nx_errata - Check for problem 450NX setup
758 * @ata_dev: the PCI device to check
760 * Check for the present of 450NX errata #19 and errata #25. If
761 * they are found return an error code so we can turn off DMA
764 static int __devinit
piix_check_450nx_errata(struct pci_dev
*ata_dev
)
766 struct pci_dev
*pdev
= NULL
;
771 while((pdev
= pci_get_device(PCI_VENDOR_ID_INTEL
, PCI_DEVICE_ID_INTEL_82454NX
, pdev
)) != NULL
)
773 /* Look for 450NX PXB. Check for problem configurations
774 A PCI quirk checks bit 6 already */
775 pci_read_config_byte(pdev
, PCI_REVISION_ID
, &rev
);
776 pci_read_config_word(pdev
, 0x41, &cfg
);
777 /* Only on the original revision: IDE DMA can hang */
780 /* On all revisions below 5 PXB bus lock must be disabled for IDE */
781 else if (cfg
& (1<<14) && rev
< 5)
785 dev_printk(KERN_WARNING
, &ata_dev
->dev
, "450NX errata present, disabling IDE DMA.\n");
786 if (no_piix_dma
== 2)
787 dev_printk(KERN_WARNING
, &ata_dev
->dev
, "A BIOS update may resolve this.\n");
791 static void __devinit
piix_init_pcs(struct pci_dev
*pdev
,
792 const struct piix_map_db
*map_db
)
796 pci_read_config_word(pdev
, ICH5_PCS
, &pcs
);
798 new_pcs
= pcs
| map_db
->port_enable
;
800 if (new_pcs
!= pcs
) {
801 DPRINTK("updating PCS from 0x%x to 0x%x\n", pcs
, new_pcs
);
802 pci_write_config_word(pdev
, ICH5_PCS
, new_pcs
);
807 static void __devinit
piix_init_sata_map(struct pci_dev
*pdev
,
808 struct ata_port_info
*pinfo
,
809 const struct piix_map_db
*map_db
)
811 struct piix_host_priv
*hpriv
= pinfo
[0].private_data
;
812 const unsigned int *map
;
813 int i
, invalid_map
= 0;
816 pci_read_config_byte(pdev
, ICH5_PMR
, &map_value
);
818 map
= map_db
->map
[map_value
& map_db
->mask
];
820 dev_printk(KERN_INFO
, &pdev
->dev
, "MAP [");
821 for (i
= 0; i
< 4; i
++) {
833 WARN_ON((i
& 1) || map
[i
+ 1] != IDE
);
834 pinfo
[i
/ 2] = piix_port_info
[ich5_pata
];
840 printk(" P%d", map
[i
]);
842 pinfo
[i
/ 2].host_flags
|= ATA_FLAG_SLAVE_POSS
;
849 dev_printk(KERN_ERR
, &pdev
->dev
,
850 "invalid MAP value %u\n", map_value
);
853 hpriv
->map_db
= map_db
;
857 * piix_init_one - Register PIIX ATA PCI device with kernel services
858 * @pdev: PCI device to register
859 * @ent: Entry in piix_pci_tbl matching with @pdev
861 * Called from kernel PCI layer. We probe for combined mode (sigh),
862 * and then hand over control to libata, for it to do the rest.
865 * Inherited from PCI layer (may sleep).
868 * Zero on success, or -ERRNO value.
871 static int piix_init_one (struct pci_dev
*pdev
, const struct pci_device_id
*ent
)
873 static int printed_version
;
874 struct ata_port_info port_info
[2];
875 struct ata_port_info
*ppinfo
[2] = { &port_info
[0], &port_info
[1] };
876 struct piix_host_priv
*hpriv
;
877 unsigned long host_flags
;
879 if (!printed_version
++)
880 dev_printk(KERN_DEBUG
, &pdev
->dev
,
881 "version " DRV_VERSION
"\n");
883 /* no hotplugging support (FIXME) */
887 hpriv
= kzalloc(sizeof(*hpriv
), GFP_KERNEL
);
891 port_info
[0] = piix_port_info
[ent
->driver_data
];
892 port_info
[1] = piix_port_info
[ent
->driver_data
];
893 port_info
[0].private_data
= hpriv
;
894 port_info
[1].private_data
= hpriv
;
896 host_flags
= port_info
[0].host_flags
;
898 if (host_flags
& PIIX_FLAG_AHCI
) {
900 pci_read_config_byte(pdev
, PIIX_SCC
, &tmp
);
901 if (tmp
== PIIX_AHCI_DEVICE
) {
902 int rc
= piix_disable_ahci(pdev
);
908 /* Initialize SATA map */
909 if (host_flags
& ATA_FLAG_SATA
) {
910 piix_init_sata_map(pdev
, port_info
,
911 piix_map_db_table
[ent
->driver_data
]);
912 piix_init_pcs(pdev
, piix_map_db_table
[ent
->driver_data
]);
915 /* On ICH5, some BIOSen disable the interrupt using the
916 * PCI_COMMAND_INTX_DISABLE bit added in PCI 2.3.
917 * On ICH6, this bit has the same effect, but only when
918 * MSI is disabled (and it is disabled, as we don't use
919 * message-signalled interrupts currently).
921 if (host_flags
& PIIX_FLAG_CHECKINTR
)
924 if (piix_check_450nx_errata(pdev
)) {
925 /* This writes into the master table but it does not
926 really matter for this errata as we will apply it to
927 all the PIIX devices on the board */
928 port_info
[0].mwdma_mask
= 0;
929 port_info
[0].udma_mask
= 0;
930 port_info
[1].mwdma_mask
= 0;
931 port_info
[1].udma_mask
= 0;
933 return ata_pci_init_one(pdev
, ppinfo
, 2);
936 static void piix_host_stop(struct ata_host_set
*host_set
)
938 if (host_set
->next
== NULL
)
939 kfree(host_set
->private_data
);
940 ata_host_stop(host_set
);
943 static int __init
piix_init(void)
947 DPRINTK("pci_module_init\n");
948 rc
= pci_module_init(&piix_pci_driver
);
958 static void __exit
piix_exit(void)
960 pci_unregister_driver(&piix_pci_driver
);
963 module_init(piix_init
);
964 module_exit(piix_exit
);