2 * Generic Generic NCR5380 driver
4 * Copyright 1993, Drew Eckhardt
6 * (Unix and Linux consulting and custom programming)
10 * NCR53C400 extensions (c) 1994,1995,1996, Kevin Lentin
11 * K.Lentin@cs.monash.edu.au
13 * NCR53C400A extensions (c) 1996, Ingmar Baumgart
14 * ingmar@gonzo.schwaben.de
16 * DTC3181E extensions (c) 1997, Ronald van Cuijlenborg
17 * ronald.van.cuijlenborg@tip.nl or nutty@dds.nl
19 * Added ISAPNP support for DTC436 adapters,
20 * Thomas Sailer, sailer@ife.ee.ethz.ch
24 * TODO : flesh out DMA support, find some one actually using this (I have
25 * a memory mapped Trantor board that works fine)
29 * The card is detected and initialized in one of several ways :
30 * 1. With command line overrides - NCR5380=port,irq may be
31 * used on the LILO command line to override the defaults.
33 * 2. With the GENERIC_NCR5380_OVERRIDE compile time define. This is
34 * specified as an array of address, irq, dma, board tuples. Ie, for
35 * one board at 0x350, IRQ5, no dma, I could say
36 * -DGENERIC_NCR5380_OVERRIDE={{0xcc000, 5, DMA_NONE, BOARD_NCR5380}}
38 * -1 should be specified for no or DMA interrupt, -2 to autoprobe for an
39 * IRQ line if overridden on the command line.
41 * 3. When included as a module, with arguments passed on the command line:
42 * ncr_irq=xx the interrupt
43 * ncr_addr=xx the port or base address (for port or memory
46 * ncr_5380=1 to set up for a NCR5380 board
47 * ncr_53c400=1 to set up for a NCR53C400 board
49 * modprobe g_NCR5380 ncr_irq=5 ncr_addr=0x350 ncr_5380=1
50 * for a port mapped NCR5380 board or
51 * modprobe g_NCR5380 ncr_irq=255 ncr_addr=0xc8000 ncr_53c400=1
52 * for a memory mapped NCR53C400 board with interrupts disabled.
54 * 255 should be specified for no or DMA interrupt, 254 to autoprobe for an
55 * IRQ line if overridden on the command line.
61 #ifdef CONFIG_SCSI_GENERIC_NCR53C400
66 #include <linux/blkdev.h>
67 #include <linux/module.h>
68 #include <scsi/scsi_host.h>
69 #include "g_NCR5380.h"
71 #include <linux/init.h>
72 #include <linux/ioport.h>
73 #include <linux/isapnp.h>
74 #include <linux/interrupt.h>
80 static int ncr_53c400
;
81 static int ncr_53c400a
;
84 static struct override
{
85 NCR5380_map_type NCR5380_map_name
;
88 int board
; /* Use NCR53c400, Ricoh, etc. extensions ? */
90 #ifdef GENERIC_NCR5380_OVERRIDE
91 [] __initdata
= GENERIC_NCR5380_OVERRIDE
;
93 [1] __initdata
= { { 0,},};
96 #define NO_OVERRIDES ARRAY_SIZE(overrides)
101 * internal_setup - handle lilo command string override
102 * @board: BOARD_* identifier for the board
104 * @ints: numeric parameters
106 * Do LILO command line initialization of the overrides array. Display
112 static void __init
internal_setup(int board
, char *str
, int *ints
)
114 static int commandline_current
;
117 if (ints
[0] != 2 && ints
[0] != 3) {
118 printk(KERN_ERR
"generic_NCR5380_setup : usage ncr5380=" STRVAL(NCR5380_map_name
) ",irq,dma\n");
122 case BOARD_NCR53C400
:
124 printk(KERN_ERR
"generic_NCR53C400_setup : usage ncr53c400=" STRVAL(NCR5380_map_name
) ",irq\n");
128 case BOARD_NCR53C400A
:
130 printk(KERN_ERR
"generic_NCR53C400A_setup : usage ncr53c400a=" STRVAL(NCR5380_map_name
) ",irq\n");
136 printk("generic_DTC3181E_setup : usage dtc3181e=" STRVAL(NCR5380_map_name
) ",irq\n");
142 if (commandline_current
< NO_OVERRIDES
) {
143 overrides
[commandline_current
].NCR5380_map_name
= (NCR5380_map_type
) ints
[1];
144 overrides
[commandline_current
].irq
= ints
[2];
146 overrides
[commandline_current
].dma
= ints
[3];
148 overrides
[commandline_current
].dma
= DMA_NONE
;
149 overrides
[commandline_current
].board
= board
;
150 ++commandline_current
;
156 * do_NCR53C80_setup - set up entry point
159 * Setup function invoked at boot to parse the ncr5380= command
163 static int __init
do_NCR5380_setup(char *str
)
167 get_options(str
, ARRAY_SIZE(ints
), ints
);
168 internal_setup(BOARD_NCR5380
, str
, ints
);
173 * do_NCR53C400_setup - set up entry point
175 * @ints: integer parameters from kernel setup code
177 * Setup function invoked at boot to parse the ncr53c400= command
181 static int __init
do_NCR53C400_setup(char *str
)
185 get_options(str
, ARRAY_SIZE(ints
), ints
);
186 internal_setup(BOARD_NCR53C400
, str
, ints
);
191 * do_NCR53C400A_setup - set up entry point
193 * @ints: integer parameters from kernel setup code
195 * Setup function invoked at boot to parse the ncr53c400a= command
199 static int __init
do_NCR53C400A_setup(char *str
)
203 get_options(str
, ARRAY_SIZE(ints
), ints
);
204 internal_setup(BOARD_NCR53C400A
, str
, ints
);
209 * do_DTC3181E_setup - set up entry point
211 * @ints: integer parameters from kernel setup code
213 * Setup function invoked at boot to parse the dtc3181e= command
217 static int __init
do_DTC3181E_setup(char *str
)
221 get_options(str
, ARRAY_SIZE(ints
), ints
);
222 internal_setup(BOARD_DTC3181E
, str
, ints
);
229 * generic_NCR5380_detect - look for NCR5380 controllers
230 * @tpnt: the scsi template
232 * Scan for the present of NCR5380, NCR53C400, NCR53C400A, DTC3181E
233 * and DTC436(ISAPnP) controllers. If overrides have been set we use
239 static int __init
generic_NCR5380_detect(struct scsi_host_template
*tpnt
)
241 static int current_override
;
244 #ifndef SCSI_G_NCR5380_MEM
246 unsigned long region_size
= 16;
248 static unsigned int __initdata ncr_53c400a_ports
[] = {
249 0x280, 0x290, 0x300, 0x310, 0x330, 0x340, 0x348, 0x350, 0
251 static unsigned int __initdata dtc_3181e_ports
[] = {
252 0x220, 0x240, 0x280, 0x2a0, 0x2c0, 0x300, 0x320, 0x340, 0
255 struct Scsi_Host
*instance
;
256 #ifdef SCSI_G_NCR5380_MEM
262 overrides
[0].irq
= ncr_irq
;
264 overrides
[0].dma
= ncr_dma
;
266 overrides
[0].NCR5380_map_name
= (NCR5380_map_type
) ncr_addr
;
268 overrides
[0].board
= BOARD_NCR5380
;
270 overrides
[0].board
= BOARD_NCR53C400
;
271 else if (ncr_53c400a
)
272 overrides
[0].board
= BOARD_NCR53C400A
;
274 overrides
[0].board
= BOARD_DTC3181E
;
275 #ifndef SCSI_G_NCR5380_MEM
276 if (!current_override
&& isapnp_present()) {
277 struct pnp_dev
*dev
= NULL
;
279 while ((dev
= pnp_find_dev(NULL
, ISAPNP_VENDOR('D', 'T', 'C'), ISAPNP_FUNCTION(0x436e), dev
))) {
280 if (count
>= NO_OVERRIDES
)
282 if (pnp_device_attach(dev
) < 0)
284 if (pnp_activate_dev(dev
) < 0) {
285 printk(KERN_ERR
"dtc436e probe: activate failed\n");
286 pnp_device_detach(dev
);
289 if (!pnp_port_valid(dev
, 0)) {
290 printk(KERN_ERR
"dtc436e probe: no valid port\n");
291 pnp_device_detach(dev
);
294 if (pnp_irq_valid(dev
, 0))
295 overrides
[count
].irq
= pnp_irq(dev
, 0);
297 overrides
[count
].irq
= NO_IRQ
;
298 if (pnp_dma_valid(dev
, 0))
299 overrides
[count
].dma
= pnp_dma(dev
, 0);
301 overrides
[count
].dma
= DMA_NONE
;
302 overrides
[count
].NCR5380_map_name
= (NCR5380_map_type
) pnp_port_start(dev
, 0);
303 overrides
[count
].board
= BOARD_DTC3181E
;
309 for (count
= 0; current_override
< NO_OVERRIDES
; ++current_override
) {
310 if (!(overrides
[current_override
].NCR5380_map_name
))
315 switch (overrides
[current_override
].board
) {
317 flags
= FLAG_NO_PSEUDO_DMA
;
319 case BOARD_NCR53C400
:
321 flags
= FLAG_NO_DMA_FIXUP
;
324 case BOARD_NCR53C400A
:
325 flags
= FLAG_NO_PSEUDO_DMA
;
326 ports
= ncr_53c400a_ports
;
329 flags
= FLAG_NO_PSEUDO_DMA
;
330 ports
= dtc_3181e_ports
;
334 #ifndef SCSI_G_NCR5380_MEM
336 /* wakeup sequence for the NCR53C400A and DTC3181E */
338 /* Disable the adapter and look for a free io port */
346 if (overrides
[current_override
].NCR5380_map_name
!= PORT_AUTO
)
347 for (i
= 0; ports
[i
]; i
++) {
348 if (!request_region(ports
[i
], 16, "ncr53c80"))
350 if (overrides
[current_override
].NCR5380_map_name
== ports
[i
])
352 release_region(ports
[i
], 16);
354 for (i
= 0; ports
[i
]; i
++) {
355 if (!request_region(ports
[i
], 16, "ncr53c80"))
357 if (inb(ports
[i
]) == 0xff)
359 release_region(ports
[i
], 16);
362 /* At this point we have our region reserved */
368 outb(0x80 | i
, 0x379); /* set io port to be used */
369 outb(0xc0, ports
[i
] + 9);
370 if (inb(ports
[i
] + 9) != 0x80)
373 overrides
[current_override
].NCR5380_map_name
= ports
[i
];
379 /* Not a 53C400A style setup - just grab */
380 if(!(request_region(overrides
[current_override
].NCR5380_map_name
, NCR5380_region_size
, "ncr5380")))
382 region_size
= NCR5380_region_size
;
385 base
= overrides
[current_override
].NCR5380_map_name
;
386 if (!request_mem_region(base
, NCR5380_region_size
, "ncr5380"))
388 iomem
= ioremap(base
, NCR5380_region_size
);
390 release_mem_region(base
, NCR5380_region_size
);
394 instance
= scsi_register(tpnt
, sizeof(struct NCR5380_hostdata
));
395 if (instance
== NULL
)
398 #ifndef SCSI_G_NCR5380_MEM
399 instance
->io_port
= overrides
[current_override
].NCR5380_map_name
;
400 instance
->n_io_port
= region_size
;
403 * On NCR53C400 boards, NCR5380 registers are mapped 8 past
406 if (overrides
[current_override
].board
== BOARD_NCR53C400
)
407 instance
->io_port
+= 8;
409 instance
->base
= overrides
[current_override
].NCR5380_map_name
;
410 ((struct NCR5380_hostdata
*)instance
->hostdata
)->iomem
= iomem
;
413 if (NCR5380_init(instance
, flags
))
416 if (overrides
[current_override
].board
== BOARD_NCR53C400
)
417 NCR5380_write(C400_CONTROL_STATUS_REG
, CSR_BASE
);
419 NCR5380_maybe_reset_bus(instance
);
421 if (overrides
[current_override
].irq
!= IRQ_AUTO
)
422 instance
->irq
= overrides
[current_override
].irq
;
424 instance
->irq
= NCR5380_probe_irq(instance
, 0xffff);
426 /* Compatibility with documented NCR5380 kernel parameters */
427 if (instance
->irq
== 255)
428 instance
->irq
= NO_IRQ
;
430 if (instance
->irq
!= NO_IRQ
)
431 if (request_irq(instance
->irq
, generic_NCR5380_intr
,
432 0, "NCR5380", instance
)) {
433 printk(KERN_WARNING
"scsi%d : IRQ%d not free, interrupts disabled\n", instance
->host_no
, instance
->irq
);
434 instance
->irq
= NO_IRQ
;
437 if (instance
->irq
== NO_IRQ
) {
438 printk(KERN_INFO
"scsi%d : interrupts not enabled. for better interactive performance,\n", instance
->host_no
);
439 printk(KERN_INFO
"scsi%d : please jumper the board for a free IRQ.\n", instance
->host_no
);
448 scsi_unregister(instance
);
450 #ifndef SCSI_G_NCR5380_MEM
451 release_region(overrides
[current_override
].NCR5380_map_name
, region_size
);
454 release_mem_region(base
, NCR5380_region_size
);
460 * generic_NCR5380_release_resources - free resources
461 * @instance: host adapter to clean up
463 * Free the generic interface resources from this adapter.
468 static int generic_NCR5380_release_resources(struct Scsi_Host
*instance
)
470 if (instance
->irq
!= NO_IRQ
)
471 free_irq(instance
->irq
, instance
);
472 NCR5380_exit(instance
);
473 #ifndef SCSI_G_NCR5380_MEM
474 release_region(instance
->io_port
, instance
->n_io_port
);
476 iounmap(((struct NCR5380_hostdata
*)instance
->hostdata
)->iomem
);
477 release_mem_region(instance
->base
, NCR5380_region_size
);
484 * generic_NCR5380_biosparam
485 * @disk: disk to compute geometry for
486 * @dev: device identifier for this disk
487 * @ip: sizes to fill in
489 * Generates a BIOS / DOS compatible H-C-S mapping for the specified
492 * XXX Most SCSI boards use this mapping, I could be incorrect. Someone
493 * using hard disks on a trantor should verify that this mapping
494 * corresponds to that used by the BIOS / ASPI driver by running the linux
495 * fdisk program and matching the H_C_S coordinates to what DOS uses.
501 generic_NCR5380_biosparam(struct scsi_device
*sdev
, struct block_device
*bdev
,
502 sector_t capacity
, int *ip
)
506 ip
[2] = capacity
>> 11;
514 * NCR5380_pread - pseudo DMA read
515 * @instance: adapter to read from
516 * @dst: buffer to read into
517 * @len: buffer length
519 * Perform a pseudo DMA mode read from an NCR53C400 or equivalent
523 static inline int NCR5380_pread(struct Scsi_Host
*instance
, unsigned char *dst
, int len
)
525 #ifdef SCSI_G_NCR5380_MEM
526 struct NCR5380_hostdata
*hostdata
= shost_priv(instance
);
528 int blocks
= len
/ 128;
532 NCR5380_write(C400_CONTROL_STATUS_REG
, CSR_BASE
| CSR_TRANS_DIR
);
533 NCR5380_write(C400_BLOCK_COUNTER_REG
, blocks
);
535 if ((bl
= NCR5380_read(C400_BLOCK_COUNTER_REG
)) == 0) {
538 if (NCR5380_read(C400_CONTROL_STATUS_REG
) & CSR_GATED_53C80_IRQ
) {
539 printk(KERN_ERR
"53C400r: Got 53C80_IRQ start=%d, blocks=%d\n", start
, blocks
);
542 while (NCR5380_read(C400_CONTROL_STATUS_REG
) & CSR_HOST_BUF_NOT_RDY
);
544 #ifndef SCSI_G_NCR5380_MEM
547 for (i
= 0; i
< 128; i
++)
548 dst
[start
+ i
] = NCR5380_read(C400_HOST_BUFFER
);
551 /* implies SCSI_G_NCR5380_MEM */
552 memcpy_fromio(dst
+ start
,
553 hostdata
->iomem
+ NCR53C400_host_buffer
, 128);
560 while (NCR5380_read(C400_CONTROL_STATUS_REG
) & CSR_HOST_BUF_NOT_RDY
)
562 // FIXME - no timeout
565 #ifndef SCSI_G_NCR5380_MEM
568 for (i
= 0; i
< 128; i
++)
569 dst
[start
+ i
] = NCR5380_read(C400_HOST_BUFFER
);
572 /* implies SCSI_G_NCR5380_MEM */
573 memcpy_fromio(dst
+ start
,
574 hostdata
->iomem
+ NCR53C400_host_buffer
, 128);
580 if (!(NCR5380_read(C400_CONTROL_STATUS_REG
) & CSR_GATED_53C80_IRQ
))
581 printk("53C400r: no 53C80 gated irq after transfer");
585 * DON'T DO THIS - THEY NEVER ARRIVE!
587 printk("53C400r: Waiting for 53C80 registers\n");
588 while (NCR5380_read(C400_CONTROL_STATUS_REG
) & CSR_53C80_REG
)
591 if (!(NCR5380_read(BUS_AND_STATUS_REG
) & BASR_END_DMA_TRANSFER
))
592 printk(KERN_ERR
"53C400r: no end dma signal\n");
598 * NCR5380_write - pseudo DMA write
599 * @instance: adapter to read from
600 * @dst: buffer to read into
601 * @len: buffer length
603 * Perform a pseudo DMA mode read from an NCR53C400 or equivalent
607 static inline int NCR5380_pwrite(struct Scsi_Host
*instance
, unsigned char *src
, int len
)
609 #ifdef SCSI_G_NCR5380_MEM
610 struct NCR5380_hostdata
*hostdata
= shost_priv(instance
);
612 int blocks
= len
/ 128;
617 NCR5380_write(C400_CONTROL_STATUS_REG
, CSR_BASE
);
618 NCR5380_write(C400_BLOCK_COUNTER_REG
, blocks
);
620 if (NCR5380_read(C400_CONTROL_STATUS_REG
) & CSR_GATED_53C80_IRQ
) {
621 printk(KERN_ERR
"53C400w: Got 53C80_IRQ start=%d, blocks=%d\n", start
, blocks
);
625 if ((bl
= NCR5380_read(C400_BLOCK_COUNTER_REG
)) == 0) {
628 while (NCR5380_read(C400_CONTROL_STATUS_REG
) & CSR_HOST_BUF_NOT_RDY
)
630 #ifndef SCSI_G_NCR5380_MEM
632 for (i
= 0; i
< 128; i
++)
633 NCR5380_write(C400_HOST_BUFFER
, src
[start
+ i
]);
636 /* implies SCSI_G_NCR5380_MEM */
637 memcpy_toio(hostdata
->iomem
+ NCR53C400_host_buffer
,
644 while (NCR5380_read(C400_CONTROL_STATUS_REG
) & CSR_HOST_BUF_NOT_RDY
)
645 ; // FIXME - no timeout
647 #ifndef SCSI_G_NCR5380_MEM
649 for (i
= 0; i
< 128; i
++)
650 NCR5380_write(C400_HOST_BUFFER
, src
[start
+ i
]);
653 /* implies SCSI_G_NCR5380_MEM */
654 memcpy_toio(hostdata
->iomem
+ NCR53C400_host_buffer
,
662 printk("53C400w: waiting for registers to be available\n");
663 THEY NEVER DO
! while (NCR5380_read(C400_CONTROL_STATUS_REG
) & CSR_53C80_REG
);
664 printk("53C400w: Got em\n");
667 /* Let's wait for this instead - could be ugly */
668 /* All documentation says to check for this. Maybe my hardware is too
669 * fast. Waiting for it seems to work fine! KLL
671 while (!(i
= NCR5380_read(C400_CONTROL_STATUS_REG
) & CSR_GATED_53C80_IRQ
))
672 ; // FIXME - no timeout
675 * I know. i is certainly != 0 here but the loop is new. See previous
679 if (!((i
= NCR5380_read(BUS_AND_STATUS_REG
)) & BASR_END_DMA_TRANSFER
))
680 printk(KERN_ERR
"53C400w: No END OF DMA bit - WHOOPS! BASR=%0x\n", i
);
682 printk(KERN_ERR
"53C400w: no 53C80 gated irq after transfer (last block)\n");
685 if (!(NCR5380_read(BUS_AND_STATUS_REG
) & BASR_END_DMA_TRANSFER
)) {
686 printk(KERN_ERR
"53C400w: no end dma signal\n");
689 while (!(NCR5380_read(TARGET_COMMAND_REG
) & TCR_LAST_BYTE_SENT
))
694 static int generic_NCR5380_dma_xfer_len(struct scsi_cmnd
*cmd
)
696 int transfersize
= cmd
->transfersize
;
698 /* Limit transfers to 32K, for xx400 & xx406
699 * pseudoDMA that transfers in 128 bytes blocks.
701 if (transfersize
> 32 * 1024 && cmd
->SCp
.this_residual
&&
702 !(cmd
->SCp
.this_residual
% transfersize
))
703 transfersize
= 32 * 1024;
708 #endif /* PSEUDO_DMA */
711 * Include the NCR5380 core code that we build our driver around
716 static struct scsi_host_template driver_template
= {
717 .proc_name
= DRV_MODULE_NAME
,
718 .name
= "Generic NCR5380/NCR53C400 SCSI",
719 .detect
= generic_NCR5380_detect
,
720 .release
= generic_NCR5380_release_resources
,
721 .info
= generic_NCR5380_info
,
722 .queuecommand
= generic_NCR5380_queue_command
,
723 .eh_abort_handler
= generic_NCR5380_abort
,
724 .eh_bus_reset_handler
= generic_NCR5380_bus_reset
,
725 .bios_param
= NCR5380_BIOSPARAM
,
728 .sg_tablesize
= SG_ALL
,
730 .use_clustering
= DISABLE_CLUSTERING
,
731 .cmd_size
= NCR5380_CMD_SIZE
,
735 #include "scsi_module.c"
737 module_param(ncr_irq
, int, 0);
738 module_param(ncr_dma
, int, 0);
739 module_param(ncr_addr
, int, 0);
740 module_param(ncr_5380
, int, 0);
741 module_param(ncr_53c400
, int, 0);
742 module_param(ncr_53c400a
, int, 0);
743 module_param(dtc_3181e
, int, 0);
744 MODULE_LICENSE("GPL");
746 #if !defined(SCSI_G_NCR5380_MEM) && defined(MODULE)
747 static struct isapnp_device_id id_table
[] = {
749 ISAPNP_ANY_ID
, ISAPNP_ANY_ID
,
750 ISAPNP_VENDOR('D', 'T', 'C'), ISAPNP_FUNCTION(0x436e),
755 MODULE_DEVICE_TABLE(isapnp
, id_table
);
758 __setup("ncr5380=", do_NCR5380_setup
);
759 __setup("ncr53c400=", do_NCR53C400_setup
);
760 __setup("ncr53c400a=", do_NCR53C400A_setup
);
761 __setup("dtc3181e=", do_DTC3181E_setup
);