2 * Copyright (C) 2005-2006 Micronas USA Inc.
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License (Version 2) as
6 * published by the Free Software Foundation.
8 * This program is distributed in the hope that it will be useful,
9 * but WITHOUT ANY WARRANTY; without even the implied warranty of
10 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
11 * GNU General Public License for more details.
13 * You should have received a copy of the GNU General Public License
14 * along with this program; if not, write to the Free Software Foundation,
15 * Inc., 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
18 #include <linux/module.h>
19 #include <linux/delay.h>
20 #include <linux/sched.h>
21 #include <linux/list.h>
22 #include <linux/unistd.h>
23 #include <linux/time.h>
24 #include <linux/device.h>
25 #include <linux/i2c.h>
26 #include <linux/mutex.h>
27 #include <linux/uaccess.h>
29 #include "go7007-priv.h"
31 /********************* Driver for on-board I2C adapter *********************/
33 /* #define GO7007_I2C_DEBUG */
35 #define SPI_I2C_ADDR_BASE 0x1400
36 #define STATUS_REG_ADDR (SPI_I2C_ADDR_BASE + 0x2)
37 #define I2C_CTRL_REG_ADDR (SPI_I2C_ADDR_BASE + 0x6)
38 #define I2C_DEV_UP_ADDR_REG_ADDR (SPI_I2C_ADDR_BASE + 0x7)
39 #define I2C_LO_ADDR_REG_ADDR (SPI_I2C_ADDR_BASE + 0x8)
40 #define I2C_DATA_REG_ADDR (SPI_I2C_ADDR_BASE + 0x9)
41 #define I2C_CLKFREQ_REG_ADDR (SPI_I2C_ADDR_BASE + 0xa)
43 #define I2C_STATE_MASK 0x0007
44 #define I2C_READ_READY_MASK 0x0008
46 /* There is only one I2C port on the TW2804 that feeds all four GO7007 VIPs
47 * on the Adlink PCI-MPG24, so access is shared between all of them. */
48 static DEFINE_MUTEX(adlink_mpg24_i2c_lock
);
50 static int go7007_i2c_xfer(struct go7007
*go
, u16 addr
, int read
,
51 u16 command
, int flags
, u8
*data
)
56 if (go
->status
== STATUS_SHUTDOWN
)
59 #ifdef GO7007_I2C_DEBUG
61 dev_dbg(go
->dev
, "go7007-i2c: reading 0x%02x on 0x%02x\n",
65 "go7007-i2c: writing 0x%02x to 0x%02x on 0x%02x\n",
66 *data
, command
, addr
);
69 mutex_lock(&go
->hw_lock
);
71 if (go
->board_id
== GO7007_BOARDID_ADLINK_MPG24
) {
72 /* Bridge the I2C port on this GO7007 to the shared bus */
73 mutex_lock(&adlink_mpg24_i2c_lock
);
74 go7007_write_addr(go
, 0x3c82, 0x0020);
77 /* Wait for I2C adapter to be ready */
78 for (i
= 0; i
< 10; ++i
) {
79 if (go7007_read_addr(go
, STATUS_REG_ADDR
, &val
) < 0)
81 if (!(val
& I2C_STATE_MASK
))
86 dev_err(go
->dev
, "go7007-i2c: I2C adapter is hung\n");
90 /* Set target register (command) */
91 go7007_write_addr(go
, I2C_CTRL_REG_ADDR
, flags
);
92 go7007_write_addr(go
, I2C_LO_ADDR_REG_ADDR
, command
);
94 /* If we're writing, send the data and target address and we're done */
96 go7007_write_addr(go
, I2C_DATA_REG_ADDR
, *data
);
97 go7007_write_addr(go
, I2C_DEV_UP_ADDR_REG_ADDR
,
98 (addr
<< 9) | (command
>> 8));
103 /* Otherwise, we're reading. First clear i2c_rx_data_rdy. */
104 if (go7007_read_addr(go
, I2C_DATA_REG_ADDR
, &val
) < 0)
107 /* Send the target address plus read flag */
108 go7007_write_addr(go
, I2C_DEV_UP_ADDR_REG_ADDR
,
109 (addr
<< 9) | 0x0100 | (command
>> 8));
111 /* Wait for i2c_rx_data_rdy */
112 for (i
= 0; i
< 10; ++i
) {
113 if (go7007_read_addr(go
, STATUS_REG_ADDR
, &val
) < 0)
115 if (val
& I2C_READ_READY_MASK
)
120 dev_err(go
->dev
, "go7007-i2c: I2C adapter is hung\n");
124 /* Retrieve the read byte */
125 if (go7007_read_addr(go
, I2C_DATA_REG_ADDR
, &val
) < 0)
131 if (go
->board_id
== GO7007_BOARDID_ADLINK_MPG24
) {
132 /* Isolate the I2C port on this GO7007 from the shared bus */
133 go7007_write_addr(go
, 0x3c82, 0x0000);
134 mutex_unlock(&adlink_mpg24_i2c_lock
);
136 mutex_unlock(&go
->hw_lock
);
140 static int go7007_smbus_xfer(struct i2c_adapter
*adapter
, u16 addr
,
141 unsigned short flags
, char read_write
,
142 u8 command
, int size
, union i2c_smbus_data
*data
)
144 struct go7007
*go
= i2c_get_adapdata(adapter
);
146 if (size
!= I2C_SMBUS_BYTE_DATA
)
148 return go7007_i2c_xfer(go
, addr
, read_write
== I2C_SMBUS_READ
, command
,
149 flags
& I2C_CLIENT_SCCB
? 0x10 : 0x00, &data
->byte
);
152 /* VERY LIMITED I2C master xfer function -- only needed because the
153 * SMBus functions only support 8-bit commands and the SAA7135 uses
154 * 16-bit commands. The I2C interface on the GO7007, as limited as
155 * it is, does support this mode. */
157 static int go7007_i2c_master_xfer(struct i2c_adapter
*adapter
,
158 struct i2c_msg msgs
[], int num
)
160 struct go7007
*go
= i2c_get_adapdata(adapter
);
163 for (i
= 0; i
< num
; ++i
) {
164 /* We can only do two things here -- write three bytes, or
165 * write two bytes and read one byte. */
166 if (msgs
[i
].len
== 2) {
167 if (i
+ 1 == num
|| msgs
[i
].addr
!= msgs
[i
+ 1].addr
||
168 (msgs
[i
].flags
& I2C_M_RD
) ||
169 !(msgs
[i
+ 1].flags
& I2C_M_RD
) ||
170 msgs
[i
+ 1].len
!= 1)
172 if (go7007_i2c_xfer(go
, msgs
[i
].addr
, 1,
173 (msgs
[i
].buf
[0] << 8) | msgs
[i
].buf
[1],
174 0x01, &msgs
[i
+ 1].buf
[0]) < 0)
177 } else if (msgs
[i
].len
== 3) {
178 if (msgs
[i
].flags
& I2C_M_RD
)
180 if (msgs
[i
].len
!= 3)
182 if (go7007_i2c_xfer(go
, msgs
[i
].addr
, 0,
183 (msgs
[i
].buf
[0] << 8) | msgs
[i
].buf
[1],
184 0x01, &msgs
[i
].buf
[2]) < 0)
193 static u32
go7007_functionality(struct i2c_adapter
*adapter
)
195 return I2C_FUNC_SMBUS_BYTE_DATA
;
198 static struct i2c_algorithm go7007_algo
= {
199 .smbus_xfer
= go7007_smbus_xfer
,
200 .master_xfer
= go7007_i2c_master_xfer
,
201 .functionality
= go7007_functionality
,
204 static struct i2c_adapter go7007_adap_templ
= {
205 .owner
= THIS_MODULE
,
206 .name
= "WIS GO7007SB",
207 .algo
= &go7007_algo
,
210 int go7007_i2c_init(struct go7007
*go
)
212 memcpy(&go
->i2c_adapter
, &go7007_adap_templ
,
213 sizeof(go7007_adap_templ
));
214 go
->i2c_adapter
.dev
.parent
= go
->dev
;
215 i2c_set_adapdata(&go
->i2c_adapter
, go
);
216 if (i2c_add_adapter(&go
->i2c_adapter
) < 0) {
218 "go7007-i2c: error: i2c_add_adapter failed\n");