drivers/staging/wilc1000/wilc_wlan_if.h

   1 /* ///////////////////////////////////////////////////////////////////////// */
   2 /*  */
   3 /* Copyright (c) Atmel Corporation.  All rights reserved. */
   4 /*  */
   5 /* Module Name:  wilc_wlan_if.h */
   6 /*  */
   7 /*  */
   8 /* ///////////////////////////////////////////////////////////////////////// */
   9
  10 #ifndef WILC_WLAN_IF_H
  11 #define WILC_WLAN_IF_H
  12
  13 #include <linux/semaphore.h>
  14 #include "linux_wlan_common.h"
  15 #include <linux/netdevice.h>
  16
  17 /********************************************
  18  *
  19  *      Debug Flags
  20  *
  21  ********************************************/
  22
  23 #define N_INIT                  0x00000001
  24 #define N_ERR                   0x00000002
  25 #define N_TXQ                   0x00000004
  26 #define N_INTR                  0x00000008
  27 #define N_RXQ                   0x00000010
  28
  29 /********************************************
  30  *
  31  *      Host Interface Defines
  32  *
  33  ********************************************/
  34
  35 #define HIF_SDIO                (0)
  36 #define HIF_SPI                 BIT(0)
  37 #define HIF_SDIO_GPIO_IRQ       BIT(2)
  38
  39 /********************************************
  40  *
  41  *      Tx/Rx Buffer Size Defines
  42  *
  43  ********************************************/
  44
  45 #define CE_TX_BUFFER_SIZE       (64 * 1024)
  46 #define CE_RX_BUFFER_SIZE       (384 * 1024)
  47
  48 /********************************************
  49  *
  50  *      Wlan Interface Defines
  51  *
  52  ********************************************/
  53
  54 typedef struct {
  55         u32 read_write:         1;
  56         u32 function:           3;
  57         u32 raw:                1;
  58         u32 address:            17;
  59         u32 data:               8;
  60 } sdio_cmd52_t;
  61
  62 typedef struct {
  63         /* struct { */
  64         u32 read_write:         1;
  65         u32 function:           3;
  66         u32 block_mode:         1;
  67         u32 increment:          1;
  68         u32 address:            17;
  69         u32 count:              9;
  70         /* } bit; */
  71         u8 *buffer;
  72         u32 block_size;
  73 } sdio_cmd53_t;
  74
  75 typedef struct {
  76         int io_type;
  77         int (*io_init)(void *);
  78         void (*io_deinit)(void *);
  79         union {
  80                 struct {
  81                         int (*spi_max_speed)(void);
  82                 } spi;
  83         } u;
  84 } wilc_wlan_io_func_t;
  85
  86 #define WILC_MAC_INDICATE_STATUS        0x1
  87 #define WILC_MAC_STATUS_INIT            -1
  88 #define WILC_MAC_STATUS_READY           0
  89 #define WILC_MAC_STATUS_CONNECT         1
  90
  91 #define WILC_MAC_INDICATE_SCAN          0x2
  92
  93 typedef struct {
  94         void *os_private;
  95 } wilc_wlan_os_context_t;
  96
  97 typedef struct {
  98         wilc_wlan_os_context_t os_context;
  99         wilc_wlan_io_func_t io_func;
 100 } wilc_wlan_inp_t;
 101
 102 struct tx_complete_data {
 103         int size;
 104         void *buff;
 105         u8 *pBssid;
 106         struct sk_buff *skb;
 107 };
 108
 109 typedef void (*wilc_tx_complete_func_t)(void *, int);
 110
 111 #define WILC_TX_ERR_NO_BUF      (-2)
 112
 113 /********************************************
 114  *
 115  *      Wlan Configuration ID
 116  *
 117  ********************************************/
 118
 119 #define MAX_SSID_LEN            33
 120 #define MAX_RATES_SUPPORTED     12
 121
 122 #define INFINITE_SLEEP_TIME     ((u32)0xFFFFFFFF)
 123
 124 typedef enum {
 125         SUPP_RATES_IE           = 1,
 126         EXT_SUPP_RATES_IE       = 50,
 127         HT_CAPABILITY_IE        = 45,
 128         RSN_IE                  = 48,
 129         WPA_IE                  = 221,
 130         WMM_IE                  = 221,
 131         P2P_IE                  = 221,
 132 } BEACON_IE;
 133
 134 typedef enum {
 135         INFRASTRUCTURE          = 0,
 136         INDEPENDENT,
 137         AP,
 138 } BSSTYPE_T;
 139
 140 typedef enum {
 141         RATE_AUTO               = 0,
 142         RATE_1MB                = 1,
 143         RATE_2MB                = 2,
 144         RATE_5MB                = 5,
 145         RATE_6MB                = 6,
 146         RATE_9MB                = 9,
 147         RATE_11MB               = 11,
 148         RATE_12MB               = 12,
 149         RATE_18MB               = 18,
 150         RATE_24MB               = 24,
 151         RATE_26MB               = 36,
 152         RATE_48MB               = 48,
 153         RATE_54MB               = 54
 154 } TX_RATE_T;
 155
 156 typedef enum {
 157         B_ONLY_MODE             = 0,    /* 1, 2 M, otherwise 5, 11 M */
 158         G_ONLY_MODE,                    /* 6,12,24 otherwise 9,18,36,48,54 */
 159         G_MIXED_11B_1_MODE,             /* 1,2,5.5,11 otherwise all on */
 160         G_MIXED_11B_2_MODE,             /* 1,2,5,11,6,12,24 otherwise all on */
 161 } G_OPERATING_MODE_T;
 162
 163 typedef enum {
 164         G_SHORT_PREAMBLE        = 0,    /* Short Preamble */
 165         G_LONG_PREAMBLE         = 1,    /* Long Preamble */
 166         G_AUTO_PREAMBLE         = 2,    /* Auto Preamble Selection */
 167 } G_PREAMBLE_T;
 168
 169 #define MAC_CONNECTED           1
 170 #define MAC_DISCONNECTED        0
 171
 172 #define SCAN_DONE               TRUE
 173 typedef enum {
 174         PASSIVE_SCAN            = 0,
 175         ACTIVE_SCAN             = 1,
 176 } SCANTYPE_T;
 177
 178 typedef enum {
 179         NO_POWERSAVE            = 0,
 180         MIN_FAST_PS             = 1,
 181         MAX_FAST_PS             = 2,
 182         MIN_PSPOLL_PS           = 3,
 183         MAX_PSPOLL_PS           = 4
 184 } USER_PS_MODE_T;
 185
 186 typedef enum {
 187         CHIP_WAKEDUP            = 0,
 188         CHIP_SLEEPING_AUTO      = 1,
 189         CHIP_SLEEPING_MANUAL    = 2
 190 } CHIP_PS_STATE_T;
 191
 192 typedef enum {
 193         ACQUIRE_ONLY            = 0,
 194         ACQUIRE_AND_WAKEUP      = 1,
 195 } BUS_ACQUIRE_T;
 196
 197 typedef enum {
 198         RELEASE_ONLY            = 0,
 199         RELEASE_ALLOW_SLEEP     = 1,
 200 } BUS_RELEASE_T;
 201
 202 typedef enum {
 203         NO_SECURITY             = 0,
 204         WEP_40                  = 0x3,
 205         WEP_104                 = 0x7,
 206         WPA_AES                 = 0x29,
 207         WPA_TKIP                = 0x49,
 208         WPA_AES_TKIP            = 0x69, /* Aes or Tkip */
 209         WPA2_AES                = 0x31,
 210         WPA2_TKIP               = 0x51,
 211         WPA2_AES_TKIP           = 0x71, /* Aes or Tkip */
 212 } SECURITY_T;
 213
 214 enum AUTHTYPE {
 215         OPEN_SYSTEM             = 1,
 216         SHARED_KEY              = 2,
 217         ANY                     = 3,
 218         IEEE8021                = 5
 219 };
 220
 221 enum SITESURVEY {
 222         SITE_SURVEY_1CH         = 0,
 223         SITE_SURVEY_ALL_CH      = 1,
 224         SITE_SURVEY_OFF         = 2
 225 };
 226
 227 typedef enum {
 228         NORMAL_ACK              = 0,
 229         NO_ACK,
 230 } ACK_POLICY_T;
 231
 232 typedef enum {
 233         DONT_RESET              = 0,
 234         DO_RESET                = 1,
 235         NO_REQUEST              = 2,
 236 } RESET_REQ_T;
 237
 238 typedef enum {
 239         REKEY_DISABLE           = 1,
 240         REKEY_TIME_BASE,
 241         REKEY_PKT_BASE,
 242         REKEY_TIME_PKT_BASE
 243 } RSNA_REKEY_POLICY_T;
 244
 245 typedef enum {
 246         FILTER_NO               = 0x00,
 247         FILTER_AP_ONLY          = 0x01,
 248         FILTER_STA_ONLY         = 0x02
 249 } SCAN_CLASS_FITLER_T;
 250
 251 typedef enum {
 252         PRI_HIGH_RSSI           = 0x00,
 253         PRI_LOW_RSSI            = 0x04,
 254         PRI_DETECT              = 0x08
 255 } SCAN_PRI_T;
 256
 257 typedef enum {
 258         CH_FILTER_OFF           = 0x00,
 259         CH_FILTER_ON            = 0x10
 260 } CH_FILTER_T;
 261
 262 typedef enum {
 263         AUTO_PROT               = 0,    /* Auto */
 264         NO_PROT,                        /* Do not use any protection */
 265         ERP_PROT,                       /* Protect all ERP frame exchanges */
 266         HT_PROT,                        /* Protect all HT frame exchanges  */
 267         GF_PROT,                        /* Protect all GF frame exchanges  */
 268 } N_PROTECTION_MODE_T;
 269
 270 typedef enum {
 271         G_SELF_CTS_PROT,
 272         G_RTS_CTS_PROT,
 273 } G_PROTECTION_MODE_T;
 274
 275 typedef enum {
 276         HT_MIXED_MODE           = 1,
 277         HT_ONLY_20MHZ_MODE,
 278         HT_ONLY_20_40MHZ_MODE,
 279 } N_OPERATING_MODE_T;
 280
 281 typedef enum {
 282         NO_DETECT               = 0,
 283         DETECT_ONLY             = 1,
 284         DETECT_PROTECT          = 2,
 285         DETECT_PROTECT_REPORT   = 3,
 286 } N_OBSS_DETECTION_T;
 287
 288 typedef enum {
 289         RTS_CTS_NONHT_PROT      = 0,    /* RTS-CTS at non-HT rate */
 290         FIRST_FRAME_NONHT_PROT,         /* First frame at non-HT rate */
 291         LSIG_TXOP_PROT,                 /* LSIG TXOP Protection */
 292         FIRST_FRAME_MIXED_PROT,         /* First frame at Mixed format */
 293 } N_PROTECTION_TYPE_T;
 294
 295 typedef enum {
 296         STATIC_MODE             = 1,
 297         DYNAMIC_MODE            = 2,
 298         MIMO_MODE               = 3,    /* power save disable */
 299 } N_SMPS_MODE_T;
 300
 301 typedef enum {
 302         DISABLE_SELF_CTS,
 303         ENABLE_SELF_CTS,
 304         DISABLE_TX_ABORT,
 305         ENABLE_TX_ABORT,
 306         HW_TRIGGER_ABORT,
 307         SW_TRIGGER_ABORT,
 308 } TX_ABORT_OPTION_T;
 309
 310 enum wid_type {
 311         WID_CHAR                = 0,
 312         WID_SHORT               = 1,
 313         WID_INT                 = 2,
 314         WID_STR                 = 3,
 315         WID_BIN_DATA            = 4,
 316         WID_BIN                 = 5,
 317         WID_IP                  = 6,
 318         WID_ADR                 = 7,
 319         WID_UNDEF               = 8,
 320         WID_TYPE_FORCE_32BIT    = 0xFFFFFFFF
 321 };
 322
 323 typedef enum {
 324         WID_NIL                         = 0xffff,
 325
 326         /*
 327          *  BSS Type
 328          *  -----------------------------------------------------------
 329          *  Configuration : Infrastructure   Independent   Access Point
 330          *  Values to set :         0               1            2
 331          *  -----------------------------------------------------------
 332          */
 333         WID_BSS_TYPE                    = 0x0000,
 334
 335         /*
 336          *  Transmit Rate
 337          *  -----------------------------------------------------------
 338          *  Configuration : 1  2  5.5  11  6  9  12  18  24  36  48  54
 339          *  Values to set : 1  2    5  11  6  9  12  18  24  36  48  54
 340          *  -----------------------------------------------------------
 341          */
 342         WID_CURRENT_TX_RATE             = 0x0001,
 343
 344         /*
 345          *  Channel
 346          *  -----------------------------------------------------------
 347          *  Configuration(g) : 1  2  3  4  5  6  7  8  9 10 11 12 13 14
 348          *  Values to set    : 1  2  3  4  5  6  7  8  9 10 11 12 13 14
 349          *  -----------------------------------------------------------
 350          */
 351         WID_CURRENT_CHANNEL             = 0x0002,
 352
 353         /*
 354          *  Preamble
 355          *  -----------------------------------------------------------
 356          *  Configuration :    short    long      Auto
 357          *  Values to set :       0       1         2
 358          *  -----------------------------------------------------------
 359          */
 360         WID_PREAMBLE                    = 0x0003,
 361
 362         /*
 363          * 11g operating mode (ignored if 11g not present)
 364          *  -----------------------------------------------------------
 365          *  Configuration :   HighPerf  Compat(RSet #1) Compat(RSet #2)
 366          *  Values to set :          1               2               3
 367          *  -----------------------------------------------------------
 368          */
 369         WID_11G_OPERATING_MODE          = 0x0004,
 370
 371         /*
 372          *  Mac status (response only)
 373          *  -----------------------------------------------------------
 374          *  Configuration :   disconnect  connect
 375          *  Values to get :          0       1
 376          *  -----------------------------------------------------------
 377          */
 378         WID_STATUS                      = 0x0005,
 379
 380         /*
 381          *  Scan type
 382          *  -----------------------------------------------------------
 383          *  Configuration :   Passive Scanning   Active Scanning
 384          *  Values to set :                  0                 1
 385          *  -----------------------------------------------------------
 386          */
 387         WID_SCAN_TYPE                   = 0x0007,
 388
 389         /*
 390          *  Key Id (WEP default key Id)
 391          *  -----------------------------------------------------------
 392          *  Configuration :   Any value between 0 to 3
 393          *  Values to set :   Same value. Default is 0
 394          *  -----------------------------------------------------------
 395          */
 396         WID_KEY_ID                      = 0x0009,
 397
 398         /*
 399          *  QoS Enable
 400          *  -----------------------------------------------------------
 401          *  Configuration :   QoS Disable   WMM Enable
 402          *  Values to set :   0             1
 403          *  -----------------------------------------------------------
 404          */
 405         WID_QOS_ENABLE                  = 0x000A,
 406
 407         /*
 408          *  Power Management
 409          *  -----------------------------------------------------------
 410          *  Configuration : NO_POWERSAVE MIN_POWERSAVE MAX_POWERSAVE
 411          *  Values to set : 0            1             2
 412          *  -----------------------------------------------------------
 413          */
 414         WID_POWER_MANAGEMENT            = 0x000B,
 415
 416         /*
 417          *  WEP/802 11I Configuration
 418          *  -----------------------------------------------------------
 419          *  Configuration:Disable WP40 WP104 WPA-AES WPA-TKIP RSN-AES RSN-TKIP
 420          *  Values (0x)  :   00     03   07     29       49       31      51
 421          *  Configuration:WPA-AES+TKIP RSN-AES+TKIP
 422          *  Values (0x)  :      69        71
 423          *  -----------------------------------------------------------
 424          */
 425         WID_11I_MODE                    = 0x000C,
 426
 427         /*
 428          *  WEP Configuration: Used in BSS STA mode only when WEP is enabled
 429          *  -----------------------------------------------------------
 430          *  Configuration : Open System Shared Key Any Type | 802.1x Auth
 431          *  Values (0x)   :    01             02         03 |    BIT2
 432          *  -----------------------------------------------------------
 433          */
 434         WID_AUTH_TYPE                   = 0x000D,
 435
 436         /*
 437          *  Site Survey Type
 438          *  -----------------------------------------------------------
 439          *  Configuration       :  Values to set
 440          *  Survey 1 Channel    :  0
 441          *  survey all Channels :  1
 442          *  Disable Site Survey :  2
 443          *  -----------------------------------------------------------
 444          */
 445         WID_SITE_SURVEY                 = 0x000E,
 446
 447         /*
 448          *  Listen Interval
 449          *  -----------------------------------------------------------
 450          *  Configuration :   Any value between 1 to 255
 451          *  Values to set :   Same value. Default is 3
 452          *  -----------------------------------------------------------
 453          */
 454         WID_LISTEN_INTERVAL             = 0x000F,
 455
 456         /*
 457          *  DTIM Period
 458          *  -----------------------------------------------------------
 459          *  Configuration :   Any value between 1 to 255
 460          *  Values to set :   Same value. Default is 3
 461          *  -----------------------------------------------------------
 462          */
 463         WID_DTIM_PERIOD                 = 0x0010,
 464
 465         /*
 466          *  ACK Policy
 467          *  -----------------------------------------------------------
 468          *  Configuration :   Normal Ack            No Ack
 469          *  Values to set :       0                   1
 470          *  -----------------------------------------------------------
 471          */
 472         WID_ACK_POLICY                  = 0x0011,
 473
 474         /*
 475          *  Reset MAC (Set only)
 476          *  -----------------------------------------------------------
 477          *  Configuration :   Don't Reset       Reset   No Request
 478          *  Values to set :       0               1         2
 479          *  -----------------------------------------------------------
 480          */
 481         WID_RESET                       = 0x0012,
 482
 483         /*
 484          *  Broadcast SSID Option: Setting this will adhere to "" SSID element
 485          *  -----------------------------------------------------------
 486          *  Configuration :   Enable             Disable
 487          *  Values to set :   1                  0
 488          *  -----------------------------------------------------------
 489          */
 490         WID_BCAST_SSID                  = 0x0015,
 491
 492         /*
 493          *  Disconnect (Station)
 494          *  -----------------------------------------------------------
 495          *  Configuration :   Association ID
 496          *  Values to set :   Association ID
 497          *  -----------------------------------------------------------
 498          */
 499         WID_DISCONNECT                  = 0x0016,
 500
 501         /*
 502          *  11a Tx Power Level
 503          *  -----------------------------------------------------------
 504          *  Configuration : Sets TX Power (Higher the value greater the power)
 505          *  Values to set : Any value between 0 and 63 (inclusive Default 48)
 506          *  -----------------------------------------------------------
 507          */
 508         WID_TX_POWER_LEVEL_11A          = 0x0018,
 509
 510         /*
 511          *  Group Key Update Policy Selection
 512          *  -----------------------------------------------------------
 513          *  Configuration : Disabled timeBased packetBased timePacketBased
 514          *  Values to set :   1            2          3              4
 515          *  -----------------------------------------------------------
 516          */
 517         WID_REKEY_POLICY                = 0x0019,
 518
 519         /*
 520          *  Allow Short Slot
 521          *  -----------------------------------------------------------
 522          *  Configuration : Disallow Short Slot      Allow Short Slot
 523          *          (Enable Only Long Slot) (Enable Short Slot if applicable)
 524          *  Values to set :    0         1
 525          *  -----------------------------------------------------------
 526          */
 527         WID_SHORT_SLOT_ALLOWED          = 0x001A,
 528
 529         WID_PHY_ACTIVE_REG              = 0x001B,
 530
 531         /*
 532          *  11b Tx Power Level
 533          *  -----------------------------------------------------------
 534          *  Configuration : Sets TX Power (Higher the value greater the power)
 535          *  Values to set : Any value between 0 and 63 (inclusive Default 48)
 536          *  -----------------------------------------------------------
 537          */
 538         WID_TX_POWER_LEVEL_11B          = 0x001D,
 539
 540         /*
 541          *  Scan Request
 542          *  -----------------------------------------------------------
 543          *  Configuration : Request default scan
 544          *  Values to set : 0
 545          *  -----------------------------------------------------------
 546          */
 547         WID_START_SCAN_REQ              = 0x001E,
 548
 549         /*
 550          *  Rssi (get only)
 551          *  -----------------------------------------------------------
 552          *  Configuration :
 553          *  Values to get : Rssi value
 554          *  -----------------------------------------------------------
 555          */
 556         WID_RSSI                        = 0x001F,
 557
 558         /*
 559          * Join Request
 560          *  -----------------------------------------------------------
 561          *  Configuration : Request to join
 562          *  Values to set : index of scan result
 563          *  -----------------------------------------------------------
 564          */
 565         WID_JOIN_REQ                    = 0x0020,
 566
 567         WID_LINKSPEED                   = 0x0026,
 568
 569         /*
 570          *  Enable User Control of TX Power
 571          *  -----------------------------------------------------------
 572          *  Configuration : Disable                  Enable
 573          *  Values to set :    0                       1
 574          *  -----------------------------------------------------------
 575          */
 576         WID_USER_CONTROL_ON_TX_POWER    = 0x0027,
 577
 578         WID_MEMORY_ACCESS_8BIT          = 0x0029,
 579
 580         /*
 581          *  Enable Auto RX Sensitivity feature
 582          *  -----------------------------------------------------------
 583          *  Configuration : Disable                  Enable
 584          *  Values to set :    0                       1
 585          *  -----------------------------------------------------------
 586          */
 587         WID_AUTO_RX_SENSITIVITY         = 0x0032,
 588
 589         /*
 590          *  Receive Buffer Based Ack
 591          *  -----------------------------------------------------------
 592          *  Configuration : Disable                  Enable
 593          *  Values to set :    0                       1
 594          *  -----------------------------------------------------------
 595          */
 596         WID_DATAFLOW_CONTROL            = 0x0033,
 597
 598         /*
 599          *  Scan Filter
 600          *  -----------------------------------------------------------
 601          *  Configuration : Class       No filter   AP only   Station Only
 602          *  Values to set :                0           1           2
 603          *  Configuration : Priority    High Rssi   Low Rssi     Detect
 604          *  Values to set :                0          0x4         0x0
 605          *  Configuration : Channel     filter off  filter on
 606          *  Values to set :                0          0x10
 607          *  -----------------------------------------------------------
 608          */
 609         WID_SCAN_FILTER                 = 0x0036,
 610
 611         /*
 612          *  Link Loss Threshold (measure in the beacon period)
 613          *  -----------------------------------------------------------
 614          *  Configuration : Any value between 10 and 254(Set to 255 disable)
 615          *  Values to set : Same value. Default is 10
 616          *  -----------------------------------------------------------
 617          */
 618         WID_LINK_LOSS_THRESHOLD         = 0x0037,
 619
 620         WID_ABORT_RUNNING_SCAN          = 0x003E,
 621
 622         /* NMAC Character WID list */
 623         WID_WPS_START                   = 0x0043,
 624
 625         /*
 626          *  Protection mode for MAC
 627          *  -----------------------------------------------------------
 628          *  Configuration :  Auto  No protection  ERP    HT    GF
 629          *  Values to set :  0     1              2      3     4
 630          *  -----------------------------------------------------------
 631          */
 632         WID_11N_PROT_MECH               = 0x0080,
 633
 634         /*
 635          *  ERP Protection type for MAC
 636          *  -----------------------------------------------------------
 637          *  Configuration :  Self-CTS   RTS-CTS
 638          *  Values to set :  0          1
 639          *  -----------------------------------------------------------
 640          */
 641         WID_11N_ERP_PROT_TYPE           = 0x0081,
 642
 643         /*
 644          *  HT Option Enable
 645          *  -----------------------------------------------------------
 646          *  Configuration :   HT Enable          HT Disable
 647          *  Values to set :   1                  0
 648          *  -----------------------------------------------------------
 649          */
 650         WID_11N_ENABLE                  = 0x0082,
 651
 652         /*
 653          *  11n Operating mode (Note that 11g operating mode will also be
 654          *  used in addition to this, if this is set to HT Mixed mode)
 655          *  -----------------------------------------------------------
 656          *   Configuration :  HT Mixed  HT Only-20MHz   HT Only-20/40MHz
 657          *  Values to set :     1         2               3
 658          *  -----------------------------------------------------------
 659          */
 660         WID_11N_OPERATING_MODE          = 0x0083,
 661
 662         /*
 663          *  11n OBSS non-HT STA Detection flag
 664          *  -----------------------------------------------------------
 665          *  Configuration :  Do not detect
 666          *  Values to set :  0
 667          *  Configuration :  Detect, do not protect or report
 668          *  Values to set :  1
 669          *  Configuration :  Detect, protect and do not report
 670          *  Values to set :  2
 671          *  Configuration :  Detect, protect and report to other BSS
 672          *  Values to set :  3
 673          *  -----------------------------------------------------------
 674          */
 675         WID_11N_OBSS_NONHT_DETECTION    = 0x0084,
 676
 677         /*
 678          *  11n HT Protection Type
 679          *  -----------------------------------------------------------
 680          *  Configuration :  RTS-CTS   First Frame Exchange at non-HT-rate
 681          *  Values to set :  0         1
 682          *  Configuration :  LSIG TXOP First Frame Exchange in Mixed Fmt
 683          *  Values to set :  2         3
 684          *  -----------------------------------------------------------
 685          */
 686         WID_11N_HT_PROT_TYPE            = 0x0085,
 687
 688         /*
 689          *  11n RIFS Protection Enable Flag
 690          *  -----------------------------------------------------------
 691          *  Configuration :  Disable    Enable
 692          *  Values to set :  0          1
 693          *  -----------------------------------------------------------
 694          */
 695         WID_11N_RIFS_PROT_ENABLE        = 0x0086,
 696
 697         /*
 698          *  SMPS Mode
 699          *  -----------------------------------------------------------
 700          *  Configuration :  Static   Dynamic   MIMO (Power Save Disabled)
 701          *  Values to set :  1        2         3
 702          *  -----------------------------------------------------------
 703          */
 704         WID_11N_SMPS_MODE               = 0x0087,
 705
 706         /*
 707          *  Current transmit MCS
 708          *  -----------------------------------------------------------
 709          *  Configuration :  MCS Index for data rate
 710          *  Values to set :  0 to 7
 711          *  -----------------------------------------------------------
 712          */
 713         WID_11N_CURRENT_TX_MCS          = 0x0088,
 714
 715         WID_11N_PRINT_STATS             = 0x0089,
 716
 717         /*
 718          *  11n Short GI Enable Flag
 719          *  -----------------------------------------------------------
 720          *  Configuration :  Disable    Enable
 721          *  Values to set :  0          1
 722          *  -----------------------------------------------------------
 723          */
 724         WID_11N_SHORT_GI_ENABLE         = 0x008D,
 725
 726         /*
 727          *  11n RIFS Enable Flag
 728          *  -----------------------------------------------------------
 729          *  Configuration :  Disable    Enable
 730          *  Values to set :  0          1
 731          *  -----------------------------------------------------------
 732          */
 733         WID_RIFS_MODE                   = 0x0094,
 734
 735         /*
 736          *  TX Abort Feature
 737          *  -----------------------------------------------------------
 738          *  Configuration :  Disable Self CTS    Enable Self CTS
 739          *  Values to set :             0                      1
 740          *  Configuration :  Disable TX Abort    Enable TX Abort
 741          *  Values to set :             2                      3
 742          *  Configuration :  Enable HW TX Abort Enable SW TX Abort
 743          *  Values to set :             4                      5
 744          *  -----------------------------------------------------------
 745          */
 746         WID_TX_ABORT_CONFIG             = 0x00A1,
 747
 748         WID_REG_TSSI_11B_VALUE          = 0x00A6,
 749         WID_REG_TSSI_11G_VALUE          = 0x00A7,
 750         WID_REG_TSSI_11N_VALUE          = 0x00A8,
 751         WID_TX_CALIBRATION              = 0x00A9,
 752         WID_DSCR_TSSI_11B_VALUE         = 0x00AA,
 753         WID_DSCR_TSSI_11G_VALUE         = 0x00AB,
 754         WID_DSCR_TSSI_11N_VALUE         = 0x00AC,
 755
 756         /*
 757          *  Immediate Block-Ack Support
 758          *  -----------------------------------------------------------
 759          *  Configuration : Disable                  Enable
 760          *  Values to set :    0                       1
 761          *  -----------------------------------------------------------
 762          */
 763         WID_11N_IMMEDIATE_BA_ENABLED    = 0x00AF,
 764
 765         /*
 766          *  TXOP Disable Flag
 767          *  -----------------------------------------------------------
 768          *  Configuration : Disable                  Enable
 769          *  Values to set :    1                        0
 770          *  -----------------------------------------------------------
 771          */
 772         WID_11N_TXOP_PROT_DISABLE       = 0x00B0,
 773
 774         WID_TX_POWER_LEVEL_11N          = 0x00B1,
 775
 776         /* Custom Character WID list */
 777         WID_PC_TEST_MODE                = 0x00C8,
 778         /* SCAN Complete notification WID*/
 779         WID_SCAN_COMPLETE               = 0x00C9,
 780
 781         WID_DEL_BEACON                  = 0x00CA,
 782
 783         WID_LOGTerminal_Switch          = 0x00CD,
 784         /*  EMAC Short WID list */
 785         /*  RTS Threshold */
 786         /*
 787          *  -----------------------------------------------------------
 788          *  Configuration :   Any value between 256 to 2347
 789          *  Values to set :   Same value. Default is 2347
 790          *  -----------------------------------------------------------
 791          */
 792         WID_RTS_THRESHOLD               = 0x1000,
 793
 794         /*
 795          *  Fragmentation Threshold
 796          *  -----------------------------------------------------------
 797          *  Configuration :   Any value between 256 to 2346
 798          *  Values to set :   Same value. Default is 2346
 799          *  -----------------------------------------------------------
 800          */
 801         WID_FRAG_THRESHOLD              = 0x1001,
 802
 803         WID_SHORT_RETRY_LIMIT           = 0x1002,
 804         WID_LONG_RETRY_LIMIT            = 0x1003,
 805         WID_BEACON_INTERVAL             = 0x1006,
 806         WID_MEMORY_ACCESS_16BIT         = 0x1008,
 807         WID_RX_SENSE                    = 0x100B,
 808         WID_ACTIVE_SCAN_TIME            = 0x100C,
 809         WID_PASSIVE_SCAN_TIME           = 0x100D,
 810
 811         WID_SITE_SURVEY_SCAN_TIME       = 0x100E,
 812         WID_JOIN_START_TIMEOUT          = 0x100F,
 813         WID_AUTH_TIMEOUT                = 0x1010,
 814         WID_ASOC_TIMEOUT                = 0x1011,
 815         WID_11I_PROTOCOL_TIMEOUT        = 0x1012,
 816         WID_EAPOL_RESPONSE_TIMEOUT      = 0x1013,
 817
 818         /* NMAC Short WID list */
 819         WID_11N_SIG_QUAL_VAL            = 0x1085,
 820         WID_CCA_THRESHOLD               = 0x1087,
 821
 822         /* Custom Short WID list */
 823
 824         /* EMAC Integer WID list */
 825         WID_FAILED_COUNT                = 0x2000,
 826         WID_RETRY_COUNT                 = 0x2001,
 827         WID_MULTIPLE_RETRY_COUNT        = 0x2002,
 828         WID_FRAME_DUPLICATE_COUNT       = 0x2003,
 829         WID_ACK_FAILURE_COUNT           = 0x2004,
 830         WID_RECEIVED_FRAGMENT_COUNT     = 0x2005,
 831         WID_MCAST_RECEIVED_FRAME_COUNT  = 0x2006,
 832         WID_FCS_ERROR_COUNT             = 0x2007,
 833         WID_SUCCESS_FRAME_COUNT         = 0x2008,
 834         WID_HUT_TX_COUNT                = 0x200A,
 835         WID_TX_FRAGMENT_COUNT           = 0x200B,
 836         WID_TX_MULTICAST_FRAME_COUNT    = 0x200C,
 837         WID_RTS_SUCCESS_COUNT           = 0x200D,
 838         WID_RTS_FAILURE_COUNT           = 0x200E,
 839         WID_WEP_UNDECRYPTABLE_COUNT     = 0x200F,
 840         WID_REKEY_PERIOD                = 0x2010,
 841         WID_REKEY_PACKET_COUNT          = 0x2011,
 842         WID_1X_SERV_ADDR                = 0x2012,
 843         WID_STACK_IP_ADDR               = 0x2013,
 844         WID_STACK_NETMASK_ADDR          = 0x2014,
 845         WID_HW_RX_COUNT                 = 0x2015,
 846         WID_MEMORY_ADDRESS              = 0x201E,
 847         WID_MEMORY_ACCESS_32BIT         = 0x201F,
 848         WID_RF_REG_VAL                  = 0x2021,
 849
 850         /* NMAC Integer WID list */
 851         WID_11N_PHY_ACTIVE_REG_VAL      = 0x2080,
 852
 853         /* Custom Integer WID list */
 854         WID_GET_INACTIVE_TIME           = 0x2084,
 855         WID_SET_DRV_HANDLER             = 0X2085,
 856         WID_SET_OPERATION_MODE          = 0X2086,
 857         /* EMAC String WID list */
 858         WID_SSID                        = 0x3000,
 859         WID_FIRMWARE_VERSION            = 0x3001,
 860         WID_OPERATIONAL_RATE_SET        = 0x3002,
 861         WID_BSSID                       = 0x3003,
 862         WID_WEP_KEY_VALUE               = 0x3004,
 863         WID_11I_PSK                     = 0x3008,
 864         WID_11E_P_ACTION_REQ            = 0x3009,
 865         WID_1X_KEY                      = 0x300A,
 866         WID_HARDWARE_VERSION            = 0x300B,
 867         WID_MAC_ADDR                    = 0x300C,
 868         WID_HUT_DEST_ADDR               = 0x300D,
 869         WID_PHY_VERSION                 = 0x300F,
 870         WID_SUPP_USERNAME               = 0x3010,
 871         WID_SUPP_PASSWORD               = 0x3011,
 872         WID_SITE_SURVEY_RESULTS         = 0x3012,
 873         WID_RX_POWER_LEVEL              = 0x3013,
 874         WID_DEL_ALL_RX_BA               = 0x3014,
 875         WID_SET_STA_MAC_INACTIVE_TIME   = 0x3017,
 876         WID_ADD_WEP_KEY                 = 0x3019,
 877         WID_REMOVE_WEP_KEY              = 0x301A,
 878         WID_ADD_PTK                     = 0x301B,
 879         WID_ADD_RX_GTK                  = 0x301C,
 880         WID_ADD_TX_GTK                  = 0x301D,
 881         WID_REMOVE_KEY                  = 0x301E,
 882         WID_ASSOC_REQ_INFO              = 0x301F,
 883         WID_ASSOC_RES_INFO              = 0x3020,
 884         WID_MANUFACTURER                = 0x3026, /*Added for CAPI tool */
 885         WID_MODEL_NAME                  = 0x3027, /*Added for CAPI tool */
 886         WID_MODEL_NUM                   = 0x3028, /*Added for CAPI tool */
 887         WID_DEVICE_NAME                 = 0x3029, /*Added for CAPI tool */
 888
 889         /* NMAC String WID list */
 890         WID_11N_P_ACTION_REQ            = 0x3080,
 891         WID_HUT_TEST_ID                 = 0x3081,
 892         WID_PMKID_INFO                  = 0x3082,
 893         WID_FIRMWARE_INFO               = 0x3083,
 894         WID_REGISTER_FRAME              = 0x3084,
 895         WID_DEL_ALL_STA                 = 0x3085,
 896         WID_REMAIN_ON_CHAN              = 0x3996,
 897         WID_SSID_PROBE_REQ              = 0x3997,
 898         WID_JOIN_REQ_EXTENDED           = 0x3998,
 899
 900         WID_IP_ADDRESS                  = 0x3999,
 901
 902         /* Custom String WID list */
 903
 904         /* EMAC Binary WID list */
 905         WID_UAPSD_CONFIG                = 0x4001,
 906         WID_UAPSD_STATUS                = 0x4002,
 907         WID_WMM_AP_AC_PARAMS            = 0x4003,
 908         WID_WMM_STA_AC_PARAMS           = 0x4004,
 909         WID_NETWORK_INFO                = 0x4005,
 910         WID_STA_JOIN_INFO               = 0x4006,
 911         WID_CONNECTED_STA_LIST          = 0x4007,
 912
 913         /* NMAC Binary WID list */
 914         WID_11N_AUTORATE_TABLE          = 0x4080,
 915
 916         WID_SCAN_CHANNEL_LIST           = 0x4084,
 917
 918         WID_INFO_ELEMENT_PROBE          = 0x4085,
 919         WID_INFO_ELEMENT_ASSOCIATE      = 0x4086,
 920         WID_ADD_STA                     = 0X4087,
 921         WID_REMOVE_STA                  = 0X4088,
 922         WID_EDIT_STA                    = 0X4089,
 923         WID_ADD_BEACON                  = 0x408a,
 924
 925         WID_SETUP_MULTICAST_FILTER      = 0x408b,
 926
 927         /* Miscellaneous WIDs */
 928         WID_ALL                         = 0x7FFE,
 929         WID_MAX                         = 0xFFFF
 930 } WID_T;
 931
 932 int wilc_wlan_init(struct net_device *dev, wilc_wlan_inp_t *inp);
 933
 934 void wilc_bus_set_max_speed(void);
 935 void wilc_bus_set_default_speed(void);
 936 u32 wilc_get_chipid(u8 update);
 937
 938 #endif