projects / deliverable / linux.git / blob
? search:


b6ce1a8b3ad8d69f26c4524611f3a13148e440d2
[deliverable/linux.git] / drivers / tty / serial / crisv10.c
1 /*
2 * Serial port driver for the ETRAX 100LX chip
3 *
4 * Copyright (C) 1998-2007 Axis Communications AB
5 *
6 * Many, many authors. Based once upon a time on serial.c for 16x50.
7 *
8 */
9
10 static char *serial_version = "$Revision: 1.25 $";
11
12 #include <linux/types.h>
13 #include <linux/errno.h>
14 #include <linux/signal.h>
15 #include <linux/sched.h>
16 #include <linux/timer.h>
17 #include <linux/interrupt.h>
18 #include <linux/tty.h>
19 #include <linux/tty_flip.h>
20 #include <linux/major.h>
21 #include <linux/string.h>
22 #include <linux/fcntl.h>
23 #include <linux/mm.h>
24 #include <linux/slab.h>
25 #include <linux/init.h>
26 #include <linux/kernel.h>
27 #include <linux/mutex.h>
28 #include <linux/bitops.h>
29 #include <linux/seq_file.h>
30 #include <linux/delay.h>
31 #include <linux/module.h>
32 #include <linux/uaccess.h>
33 #include <linux/io.h>
34
35 #include <asm/irq.h>
36 #include <asm/dma.h>
37
38 #include <arch/svinto.h>
39 #include <arch/system.h>
40
41 /* non-arch dependent serial structures are in linux/serial.h */
42 #include <linux/serial.h>
43 /* while we keep our own stuff (struct e100_serial) in a local .h file */
44 #include "crisv10.h"
45 #include <asm/fasttimer.h>
46 #include <arch/io_interface_mux.h>
47
48 #ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER
49 #ifndef CONFIG_ETRAX_FAST_TIMER
50 #error "Enable FAST_TIMER to use SERIAL_FAST_TIMER"
51 #endif
52 #endif
53
54 #if defined(CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS) && \
55 (CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS == 0)
56 #error "RX_TIMEOUT_TICKS == 0 not allowed, use 1"
57 #endif
58
59 #if defined(CONFIG_ETRAX_RS485_ON_PA) && defined(CONFIG_ETRAX_RS485_ON_PORT_G)
60 #error "Disable either CONFIG_ETRAX_RS485_ON_PA or CONFIG_ETRAX_RS485_ON_PORT_G"
61 #endif
62
63 /*
64 * All of the compatibilty code so we can compile serial.c against
65 * older kernels is hidden in serial_compat.h
66 */
67 #if defined(LOCAL_HEADERS)
68 #include "serial_compat.h"
69 #endif
70
71 struct tty_driver *serial_driver;
72
73 /* number of characters left in xmit buffer before we ask for more */
74 #define WAKEUP_CHARS 256
75
76 //#define SERIAL_DEBUG_INTR
77 //#define SERIAL_DEBUG_OPEN
78 //#define SERIAL_DEBUG_FLOW
79 //#define SERIAL_DEBUG_DATA
80 //#define SERIAL_DEBUG_THROTTLE
81 //#define SERIAL_DEBUG_IO /* Debug for Extra control and status pins */
82 //#define SERIAL_DEBUG_LINE 0 /* What serport we want to debug */
83
84 /* Enable this to use serial interrupts to handle when you
85 expect the first received event on the serial port to
86 be an error, break or similar. Used to be able to flash IRMA
87 from eLinux */
88 #define SERIAL_HANDLE_EARLY_ERRORS
89
90 /* Currently 16 descriptors x 128 bytes = 2048 bytes */
91 #define SERIAL_DESCR_BUF_SIZE 256
92
93 #define SERIAL_PRESCALE_BASE 3125000 /* 3.125MHz */
94 #define DEF_BAUD_BASE SERIAL_PRESCALE_BASE
95
96 /* We don't want to load the system with massive fast timer interrupt
97 * on high baudrates so limit it to 250 us (4kHz) */
98 #define MIN_FLUSH_TIME_USEC 250
99
100 /* Add an x here to log a lot of timer stuff */
101 #define TIMERD(x)
102 /* Debug details of interrupt handling */
103 #define DINTR1(x) /* irq on/off, errors */
104 #define DINTR2(x) /* tx and rx */
105 /* Debug flip buffer stuff */
106 #define DFLIP(x)
107 /* Debug flow control and overview of data flow */
108 #define DFLOW(x)
109 #define DBAUD(x)
110 #define DLOG_INT_TRIG(x)
111
112 //#define DEBUG_LOG_INCLUDED
113 #ifndef DEBUG_LOG_INCLUDED
114 #define DEBUG_LOG(line, string, value)
115 #else
116 struct debug_log_info
117 {
118 unsigned long time;
119 unsigned long timer_data;
120 // int line;
121 const char *string;
122 int value;
123 };
124 #define DEBUG_LOG_SIZE 4096
125
126 struct debug_log_info debug_log[DEBUG_LOG_SIZE];
127 int debug_log_pos = 0;
128
129 #define DEBUG_LOG(_line, _string, _value) do { \
130 if ((_line) == SERIAL_DEBUG_LINE) {\
131 debug_log_func(_line, _string, _value); \
132 }\
133 }while(0)
134
135 void debug_log_func(int line, const char *string, int value)
136 {
137 if (debug_log_pos < DEBUG_LOG_SIZE) {
138 debug_log[debug_log_pos].time = jiffies;
139 debug_log[debug_log_pos].timer_data = *R_TIMER_DATA;
140 // debug_log[debug_log_pos].line = line;
141 debug_log[debug_log_pos].string = string;
142 debug_log[debug_log_pos].value = value;
143 debug_log_pos++;
144 }
145 /*printk(string, value);*/
146 }
147 #endif
148
149 #ifndef CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS
150 /* Default number of timer ticks before flushing rx fifo
151 * When using "little data, low latency applications: use 0
152 * When using "much data applications (PPP)" use ~5
153 */
154 #define CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS 5
155 #endif
156
157 unsigned long timer_data_to_ns(unsigned long timer_data);
158
159 static void change_speed(struct e100_serial *info);
160 static void rs_throttle(struct tty_struct * tty);
161 static void rs_wait_until_sent(struct tty_struct *tty, int timeout);
162 static int rs_write(struct tty_struct *tty,
163 const unsigned char *buf, int count);
164 #ifdef CONFIG_ETRAX_RS485
165 static int e100_write_rs485(struct tty_struct *tty,
166 const unsigned char *buf, int count);
167 #endif
168 static int get_lsr_info(struct e100_serial *info, unsigned int *value);
169
170
171 #define DEF_BAUD 115200 /* 115.2 kbit/s */
172 #define DEF_RX 0x20 /* or SERIAL_CTRL_W >> 8 */
173 /* Default value of tx_ctrl register: has txd(bit 7)=1 (idle) as default */
174 #define DEF_TX 0x80 /* or SERIAL_CTRL_B */
175
176 /* offsets from R_SERIALx_CTRL */
177
178 #define REG_DATA 0
179 #define REG_DATA_STATUS32 0 /* this is the 32 bit register R_SERIALx_READ */
180 #define REG_TR_DATA 0
181 #define REG_STATUS 1
182 #define REG_TR_CTRL 1
183 #define REG_REC_CTRL 2
184 #define REG_BAUD 3
185 #define REG_XOFF 4 /* this is a 32 bit register */
186
187 /* The bitfields are the same for all serial ports */
188 #define SER_RXD_MASK IO_MASK(R_SERIAL0_STATUS, rxd)
189 #define SER_DATA_AVAIL_MASK IO_MASK(R_SERIAL0_STATUS, data_avail)
190 #define SER_FRAMING_ERR_MASK IO_MASK(R_SERIAL0_STATUS, framing_err)
191 #define SER_PAR_ERR_MASK IO_MASK(R_SERIAL0_STATUS, par_err)
192 #define SER_OVERRUN_MASK IO_MASK(R_SERIAL0_STATUS, overrun)
193
194 #define SER_ERROR_MASK (SER_OVERRUN_MASK | SER_PAR_ERR_MASK | SER_FRAMING_ERR_MASK)
195
196 /* Values for info->errorcode */
197 #define ERRCODE_SET_BREAK (TTY_BREAK)
198 #define ERRCODE_INSERT 0x100
199 #define ERRCODE_INSERT_BREAK (ERRCODE_INSERT | TTY_BREAK)
200
201 #define FORCE_EOP(info) *R_SET_EOP = 1U << info->iseteop;
202
203 /*
204 * General note regarding the use of IO_* macros in this file:
205 *
206 * We will use the bits defined for DMA channel 6 when using various
207 * IO_* macros (e.g. IO_STATE, IO_MASK, IO_EXTRACT) and _assume_ they are
208 * the same for all channels (which of course they are).
209 *
210 * We will also use the bits defined for serial port 0 when writing commands
211 * to the different ports, as these bits too are the same for all ports.
212 */
213
214
215 /* Mask for the irqs possibly enabled in R_IRQ_MASK1_RD etc. */
216 static const unsigned long e100_ser_int_mask = 0
217 #ifdef CONFIG_ETRAX_SERIAL_PORT0
218 | IO_MASK(R_IRQ_MASK1_RD, ser0_data) | IO_MASK(R_IRQ_MASK1_RD, ser0_ready)
219 #endif
220 #ifdef CONFIG_ETRAX_SERIAL_PORT1
221 | IO_MASK(R_IRQ_MASK1_RD, ser1_data) | IO_MASK(R_IRQ_MASK1_RD, ser1_ready)
222 #endif
223 #ifdef CONFIG_ETRAX_SERIAL_PORT2
224 | IO_MASK(R_IRQ_MASK1_RD, ser2_data) | IO_MASK(R_IRQ_MASK1_RD, ser2_ready)
225 #endif
226 #ifdef CONFIG_ETRAX_SERIAL_PORT3
227 | IO_MASK(R_IRQ_MASK1_RD, ser3_data) | IO_MASK(R_IRQ_MASK1_RD, ser3_ready)
228 #endif
229 ;
230 unsigned long r_alt_ser_baudrate_shadow = 0;
231
232 /* this is the data for the four serial ports in the etrax100 */
233 /* DMA2(ser2), DMA4(ser3), DMA6(ser0) or DMA8(ser1) */
234 /* R_DMA_CHx_CLR_INTR, R_DMA_CHx_FIRST, R_DMA_CHx_CMD */
235
236 static struct e100_serial rs_table[] = {
237 { .baud = DEF_BAUD,
238 .ioport = (unsigned char *)R_SERIAL0_CTRL,
239 .irq = 1U << 12, /* uses DMA 6 and 7 */
240 .oclrintradr = R_DMA_CH6_CLR_INTR,
241 .ofirstadr = R_DMA_CH6_FIRST,
242 .ocmdadr = R_DMA_CH6_CMD,
243 .ostatusadr = R_DMA_CH6_STATUS,
244 .iclrintradr = R_DMA_CH7_CLR_INTR,
245 .ifirstadr = R_DMA_CH7_FIRST,
246 .icmdadr = R_DMA_CH7_CMD,
247 .idescradr = R_DMA_CH7_DESCR,
248 .rx_ctrl = DEF_RX,
249 .tx_ctrl = DEF_TX,
250 .iseteop = 2,
251 .dma_owner = dma_ser0,
252 .io_if = if_serial_0,
253 #ifdef CONFIG_ETRAX_SERIAL_PORT0
254 .enabled = 1,
255 #ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA6_OUT
256 .dma_out_enabled = 1,
257 .dma_out_nbr = SER0_TX_DMA_NBR,
258 .dma_out_irq_nbr = SER0_DMA_TX_IRQ_NBR,
259 .dma_out_irq_flags = 0,
260 .dma_out_irq_description = "serial 0 dma tr",
261 #else
262 .dma_out_enabled = 0,
263 .dma_out_nbr = UINT_MAX,
264 .dma_out_irq_nbr = 0,
265 .dma_out_irq_flags = 0,
266 .dma_out_irq_description = NULL,
267 #endif
268 #ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA7_IN
269 .dma_in_enabled = 1,
270 .dma_in_nbr = SER0_RX_DMA_NBR,
271 .dma_in_irq_nbr = SER0_DMA_RX_IRQ_NBR,
272 .dma_in_irq_flags = 0,
273 .dma_in_irq_description = "serial 0 dma rec",
274 #else
275 .dma_in_enabled = 0,
276 .dma_in_nbr = UINT_MAX,
277 .dma_in_irq_nbr = 0,
278 .dma_in_irq_flags = 0,
279 .dma_in_irq_description = NULL,
280 #endif
281 #else
282 .enabled = 0,
283 .io_if_description = NULL,
284 .dma_out_enabled = 0,
285 .dma_in_enabled = 0
286 #endif
287
288 }, /* ttyS0 */
289 { .baud = DEF_BAUD,
290 .ioport = (unsigned char *)R_SERIAL1_CTRL,
291 .irq = 1U << 16, /* uses DMA 8 and 9 */
292 .oclrintradr = R_DMA_CH8_CLR_INTR,
293 .ofirstadr = R_DMA_CH8_FIRST,
294 .ocmdadr = R_DMA_CH8_CMD,
295 .ostatusadr = R_DMA_CH8_STATUS,
296 .iclrintradr = R_DMA_CH9_CLR_INTR,
297 .ifirstadr = R_DMA_CH9_FIRST,
298 .icmdadr = R_DMA_CH9_CMD,
299 .idescradr = R_DMA_CH9_DESCR,
300 .rx_ctrl = DEF_RX,
301 .tx_ctrl = DEF_TX,
302 .iseteop = 3,
303 .dma_owner = dma_ser1,
304 .io_if = if_serial_1,
305 #ifdef CONFIG_ETRAX_SERIAL_PORT1
306 .enabled = 1,
307 .io_if_description = "ser1",
308 #ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA8_OUT
309 .dma_out_enabled = 1,
310 .dma_out_nbr = SER1_TX_DMA_NBR,
311 .dma_out_irq_nbr = SER1_DMA_TX_IRQ_NBR,
312 .dma_out_irq_flags = 0,
313 .dma_out_irq_description = "serial 1 dma tr",
314 #else
315 .dma_out_enabled = 0,
316 .dma_out_nbr = UINT_MAX,
317 .dma_out_irq_nbr = 0,
318 .dma_out_irq_flags = 0,
319 .dma_out_irq_description = NULL,
320 #endif
321 #ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA9_IN
322 .dma_in_enabled = 1,
323 .dma_in_nbr = SER1_RX_DMA_NBR,
324 .dma_in_irq_nbr = SER1_DMA_RX_IRQ_NBR,
325 .dma_in_irq_flags = 0,
326 .dma_in_irq_description = "serial 1 dma rec",
327 #else
328 .dma_in_enabled = 0,
329 .dma_in_enabled = 0,
330 .dma_in_nbr = UINT_MAX,
331 .dma_in_irq_nbr = 0,
332 .dma_in_irq_flags = 0,
333 .dma_in_irq_description = NULL,
334 #endif
335 #else
336 .enabled = 0,
337 .io_if_description = NULL,
338 .dma_in_irq_nbr = 0,
339 .dma_out_enabled = 0,
340 .dma_in_enabled = 0
341 #endif
342 }, /* ttyS1 */
343
344 { .baud = DEF_BAUD,
345 .ioport = (unsigned char *)R_SERIAL2_CTRL,
346 .irq = 1U << 4, /* uses DMA 2 and 3 */
347 .oclrintradr = R_DMA_CH2_CLR_INTR,
348 .ofirstadr = R_DMA_CH2_FIRST,
349 .ocmdadr = R_DMA_CH2_CMD,
350 .ostatusadr = R_DMA_CH2_STATUS,
351 .iclrintradr = R_DMA_CH3_CLR_INTR,
352 .ifirstadr = R_DMA_CH3_FIRST,
353 .icmdadr = R_DMA_CH3_CMD,
354 .idescradr = R_DMA_CH3_DESCR,
355 .rx_ctrl = DEF_RX,
356 .tx_ctrl = DEF_TX,
357 .iseteop = 0,
358 .dma_owner = dma_ser2,
359 .io_if = if_serial_2,
360 #ifdef CONFIG_ETRAX_SERIAL_PORT2
361 .enabled = 1,
362 .io_if_description = "ser2",
363 #ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA2_OUT
364 .dma_out_enabled = 1,
365 .dma_out_nbr = SER2_TX_DMA_NBR,
366 .dma_out_irq_nbr = SER2_DMA_TX_IRQ_NBR,
367 .dma_out_irq_flags = 0,
368 .dma_out_irq_description = "serial 2 dma tr",
369 #else
370 .dma_out_enabled = 0,
371 .dma_out_nbr = UINT_MAX,
372 .dma_out_irq_nbr = 0,
373 .dma_out_irq_flags = 0,
374 .dma_out_irq_description = NULL,
375 #endif
376 #ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA3_IN
377 .dma_in_enabled = 1,
378 .dma_in_nbr = SER2_RX_DMA_NBR,
379 .dma_in_irq_nbr = SER2_DMA_RX_IRQ_NBR,
380 .dma_in_irq_flags = 0,
381 .dma_in_irq_description = "serial 2 dma rec",
382 #else
383 .dma_in_enabled = 0,
384 .dma_in_nbr = UINT_MAX,
385 .dma_in_irq_nbr = 0,
386 .dma_in_irq_flags = 0,
387 .dma_in_irq_description = NULL,
388 #endif
389 #else
390 .enabled = 0,
391 .io_if_description = NULL,
392 .dma_out_enabled = 0,
393 .dma_in_enabled = 0
394 #endif
395 }, /* ttyS2 */
396
397 { .baud = DEF_BAUD,
398 .ioport = (unsigned char *)R_SERIAL3_CTRL,
399 .irq = 1U << 8, /* uses DMA 4 and 5 */
400 .oclrintradr = R_DMA_CH4_CLR_INTR,
401 .ofirstadr = R_DMA_CH4_FIRST,
402 .ocmdadr = R_DMA_CH4_CMD,
403 .ostatusadr = R_DMA_CH4_STATUS,
404 .iclrintradr = R_DMA_CH5_CLR_INTR,
405 .ifirstadr = R_DMA_CH5_FIRST,
406 .icmdadr = R_DMA_CH5_CMD,
407 .idescradr = R_DMA_CH5_DESCR,
408 .rx_ctrl = DEF_RX,
409 .tx_ctrl = DEF_TX,
410 .iseteop = 1,
411 .dma_owner = dma_ser3,
412 .io_if = if_serial_3,
413 #ifdef CONFIG_ETRAX_SERIAL_PORT3
414 .enabled = 1,
415 .io_if_description = "ser3",
416 #ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA4_OUT
417 .dma_out_enabled = 1,
418 .dma_out_nbr = SER3_TX_DMA_NBR,
419 .dma_out_irq_nbr = SER3_DMA_TX_IRQ_NBR,
420 .dma_out_irq_flags = 0,
421 .dma_out_irq_description = "serial 3 dma tr",
422 #else
423 .dma_out_enabled = 0,
424 .dma_out_nbr = UINT_MAX,
425 .dma_out_irq_nbr = 0,
426 .dma_out_irq_flags = 0,
427 .dma_out_irq_description = NULL,
428 #endif
429 #ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA5_IN
430 .dma_in_enabled = 1,
431 .dma_in_nbr = SER3_RX_DMA_NBR,
432 .dma_in_irq_nbr = SER3_DMA_RX_IRQ_NBR,
433 .dma_in_irq_flags = 0,
434 .dma_in_irq_description = "serial 3 dma rec",
435 #else
436 .dma_in_enabled = 0,
437 .dma_in_nbr = UINT_MAX,
438 .dma_in_irq_nbr = 0,
439 .dma_in_irq_flags = 0,
440 .dma_in_irq_description = NULL
441 #endif
442 #else
443 .enabled = 0,
444 .io_if_description = NULL,
445 .dma_out_enabled = 0,
446 .dma_in_enabled = 0
447 #endif
448 } /* ttyS3 */
449 };
450
451
452 #define NR_PORTS (sizeof(rs_table)/sizeof(struct e100_serial))
453
454 #ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER
455 static struct fast_timer fast_timers[NR_PORTS];
456 #endif
457
458 #ifdef CONFIG_ETRAX_SERIAL_PROC_ENTRY
459 #define PROCSTAT(x) x
460 struct ser_statistics_type {
461 int overrun_cnt;
462 int early_errors_cnt;
463 int ser_ints_ok_cnt;
464 int errors_cnt;
465 unsigned long int processing_flip;
466 unsigned long processing_flip_still_room;
467 unsigned long int timeout_flush_cnt;
468 int rx_dma_ints;
469 int tx_dma_ints;
470 int rx_tot;
471 int tx_tot;
472 };
473
474 static struct ser_statistics_type ser_stat[NR_PORTS];
475
476 #else
477
478 #define PROCSTAT(x)
479
480 #endif /* CONFIG_ETRAX_SERIAL_PROC_ENTRY */
481
482 /* RS-485 */
483 #if defined(CONFIG_ETRAX_RS485)
484 #ifdef CONFIG_ETRAX_FAST_TIMER
485 static struct fast_timer fast_timers_rs485[NR_PORTS];
486 #endif
487 #if defined(CONFIG_ETRAX_RS485_ON_PA)
488 static int rs485_pa_bit = CONFIG_ETRAX_RS485_ON_PA_BIT;
489 #endif
490 #if defined(CONFIG_ETRAX_RS485_ON_PORT_G)
491 static int rs485_port_g_bit = CONFIG_ETRAX_RS485_ON_PORT_G_BIT;
492 #endif
493 #endif
494
495 /* Info and macros needed for each ports extra control/status signals. */
496 #define E100_STRUCT_PORT(line, pinname) \
497 ((CONFIG_ETRAX_SER##line##_##pinname##_ON_PA_BIT >= 0)? \
498 (R_PORT_PA_DATA): ( \
499 (CONFIG_ETRAX_SER##line##_##pinname##_ON_PB_BIT >= 0)? \
500 (R_PORT_PB_DATA):&dummy_ser[line]))
501
502 #define E100_STRUCT_SHADOW(line, pinname) \
503 ((CONFIG_ETRAX_SER##line##_##pinname##_ON_PA_BIT >= 0)? \
504 (&port_pa_data_shadow): ( \
505 (CONFIG_ETRAX_SER##line##_##pinname##_ON_PB_BIT >= 0)? \
506 (&port_pb_data_shadow):&dummy_ser[line]))
507 #define E100_STRUCT_MASK(line, pinname) \
508 ((CONFIG_ETRAX_SER##line##_##pinname##_ON_PA_BIT >= 0)? \
509 (1<<CONFIG_ETRAX_SER##line##_##pinname##_ON_PA_BIT): ( \
510 (CONFIG_ETRAX_SER##line##_##pinname##_ON_PB_BIT >= 0)? \
511 (1<<CONFIG_ETRAX_SER##line##_##pinname##_ON_PB_BIT):DUMMY_##pinname##_MASK))
512
513 #define DUMMY_DTR_MASK 1
514 #define DUMMY_RI_MASK 2
515 #define DUMMY_DSR_MASK 4
516 #define DUMMY_CD_MASK 8
517 static unsigned char dummy_ser[NR_PORTS] = {0xFF, 0xFF, 0xFF,0xFF};
518
519 /* If not all status pins are used or disabled, use mixed mode */
520 #ifdef CONFIG_ETRAX_SERIAL_PORT0
521
522 #define SER0_PA_BITSUM (CONFIG_ETRAX_SER0_DTR_ON_PA_BIT+CONFIG_ETRAX_SER0_RI_ON_PA_BIT+CONFIG_ETRAX_SER0_DSR_ON_PA_BIT+CONFIG_ETRAX_SER0_CD_ON_PA_BIT)
523
524 #if SER0_PA_BITSUM != -4
525 # if CONFIG_ETRAX_SER0_DTR_ON_PA_BIT == -1
526 # ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED
527 # define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1
528 # endif
529 # endif
530 # if CONFIG_ETRAX_SER0_RI_ON_PA_BIT == -1
531 # ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED
532 # define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1
533 # endif
534 # endif
535 # if CONFIG_ETRAX_SER0_DSR_ON_PA_BIT == -1
536 # ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED
537 # define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1
538 # endif
539 # endif
540 # if CONFIG_ETRAX_SER0_CD_ON_PA_BIT == -1
541 # ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED
542 # define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1
543 # endif
544 # endif
545 #endif
546
547 #define SER0_PB_BITSUM (CONFIG_ETRAX_SER0_DTR_ON_PB_BIT+CONFIG_ETRAX_SER0_RI_ON_PB_BIT+CONFIG_ETRAX_SER0_DSR_ON_PB_BIT+CONFIG_ETRAX_SER0_CD_ON_PB_BIT)
548
549 #if SER0_PB_BITSUM != -4
550 # if CONFIG_ETRAX_SER0_DTR_ON_PB_BIT == -1
551 # ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED
552 # define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1
553 # endif
554 # endif
555 # if CONFIG_ETRAX_SER0_RI_ON_PB_BIT == -1
556 # ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED
557 # define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1
558 # endif
559 # endif
560 # if CONFIG_ETRAX_SER0_DSR_ON_PB_BIT == -1
561 # ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED
562 # define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1
563 # endif
564 # endif
565 # if CONFIG_ETRAX_SER0_CD_ON_PB_BIT == -1
566 # ifndef CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED
567 # define CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED 1
568 # endif
569 # endif
570 #endif
571
572 #endif /* PORT0 */
573
574
575 #ifdef CONFIG_ETRAX_SERIAL_PORT1
576
577 #define SER1_PA_BITSUM (CONFIG_ETRAX_SER1_DTR_ON_PA_BIT+CONFIG_ETRAX_SER1_RI_ON_PA_BIT+CONFIG_ETRAX_SER1_DSR_ON_PA_BIT+CONFIG_ETRAX_SER1_CD_ON_PA_BIT)
578
579 #if SER1_PA_BITSUM != -4
580 # if CONFIG_ETRAX_SER1_DTR_ON_PA_BIT == -1
581 # ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED
582 # define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1
583 # endif
584 # endif
585 # if CONFIG_ETRAX_SER1_RI_ON_PA_BIT == -1
586 # ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED
587 # define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1
588 # endif
589 # endif
590 # if CONFIG_ETRAX_SER1_DSR_ON_PA_BIT == -1
591 # ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED
592 # define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1
593 # endif
594 # endif
595 # if CONFIG_ETRAX_SER1_CD_ON_PA_BIT == -1
596 # ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED
597 # define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1
598 # endif
599 # endif
600 #endif
601
602 #define SER1_PB_BITSUM (CONFIG_ETRAX_SER1_DTR_ON_PB_BIT+CONFIG_ETRAX_SER1_RI_ON_PB_BIT+CONFIG_ETRAX_SER1_DSR_ON_PB_BIT+CONFIG_ETRAX_SER1_CD_ON_PB_BIT)
603
604 #if SER1_PB_BITSUM != -4
605 # if CONFIG_ETRAX_SER1_DTR_ON_PB_BIT == -1
606 # ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED
607 # define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1
608 # endif
609 # endif
610 # if CONFIG_ETRAX_SER1_RI_ON_PB_BIT == -1
611 # ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED
612 # define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1
613 # endif
614 # endif
615 # if CONFIG_ETRAX_SER1_DSR_ON_PB_BIT == -1
616 # ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED
617 # define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1
618 # endif
619 # endif
620 # if CONFIG_ETRAX_SER1_CD_ON_PB_BIT == -1
621 # ifndef CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED
622 # define CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED 1
623 # endif
624 # endif
625 #endif
626
627 #endif /* PORT1 */
628
629 #ifdef CONFIG_ETRAX_SERIAL_PORT2
630
631 #define SER2_PA_BITSUM (CONFIG_ETRAX_SER2_DTR_ON_PA_BIT+CONFIG_ETRAX_SER2_RI_ON_PA_BIT+CONFIG_ETRAX_SER2_DSR_ON_PA_BIT+CONFIG_ETRAX_SER2_CD_ON_PA_BIT)
632
633 #if SER2_PA_BITSUM != -4
634 # if CONFIG_ETRAX_SER2_DTR_ON_PA_BIT == -1
635 # ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED
636 # define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1
637 # endif
638 # endif
639 # if CONFIG_ETRAX_SER2_RI_ON_PA_BIT == -1
640 # ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED
641 # define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1
642 # endif
643 # endif
644 # if CONFIG_ETRAX_SER2_DSR_ON_PA_BIT == -1
645 # ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED
646 # define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1
647 # endif
648 # endif
649 # if CONFIG_ETRAX_SER2_CD_ON_PA_BIT == -1
650 # ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED
651 # define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1
652 # endif
653 # endif
654 #endif
655
656 #define SER2_PB_BITSUM (CONFIG_ETRAX_SER2_DTR_ON_PB_BIT+CONFIG_ETRAX_SER2_RI_ON_PB_BIT+CONFIG_ETRAX_SER2_DSR_ON_PB_BIT+CONFIG_ETRAX_SER2_CD_ON_PB_BIT)
657
658 #if SER2_PB_BITSUM != -4
659 # if CONFIG_ETRAX_SER2_DTR_ON_PB_BIT == -1
660 # ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED
661 # define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1
662 # endif
663 # endif
664 # if CONFIG_ETRAX_SER2_RI_ON_PB_BIT == -1
665 # ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED
666 # define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1
667 # endif
668 # endif
669 # if CONFIG_ETRAX_SER2_DSR_ON_PB_BIT == -1
670 # ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED
671 # define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1
672 # endif
673 # endif
674 # if CONFIG_ETRAX_SER2_CD_ON_PB_BIT == -1
675 # ifndef CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED
676 # define CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED 1
677 # endif
678 # endif
679 #endif
680
681 #endif /* PORT2 */
682
683 #ifdef CONFIG_ETRAX_SERIAL_PORT3
684
685 #define SER3_PA_BITSUM (CONFIG_ETRAX_SER3_DTR_ON_PA_BIT+CONFIG_ETRAX_SER3_RI_ON_PA_BIT+CONFIG_ETRAX_SER3_DSR_ON_PA_BIT+CONFIG_ETRAX_SER3_CD_ON_PA_BIT)
686
687 #if SER3_PA_BITSUM != -4
688 # if CONFIG_ETRAX_SER3_DTR_ON_PA_BIT == -1
689 # ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED
690 # define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1
691 # endif
692 # endif
693 # if CONFIG_ETRAX_SER3_RI_ON_PA_BIT == -1
694 # ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED
695 # define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1
696 # endif
697 # endif
698 # if CONFIG_ETRAX_SER3_DSR_ON_PA_BIT == -1
699 # ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED
700 # define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1
701 # endif
702 # endif
703 # if CONFIG_ETRAX_SER3_CD_ON_PA_BIT == -1
704 # ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED
705 # define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1
706 # endif
707 # endif
708 #endif
709
710 #define SER3_PB_BITSUM (CONFIG_ETRAX_SER3_DTR_ON_PB_BIT+CONFIG_ETRAX_SER3_RI_ON_PB_BIT+CONFIG_ETRAX_SER3_DSR_ON_PB_BIT+CONFIG_ETRAX_SER3_CD_ON_PB_BIT)
711
712 #if SER3_PB_BITSUM != -4
713 # if CONFIG_ETRAX_SER3_DTR_ON_PB_BIT == -1
714 # ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED
715 # define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1
716 # endif
717 # endif
718 # if CONFIG_ETRAX_SER3_RI_ON_PB_BIT == -1
719 # ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED
720 # define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1
721 # endif
722 # endif
723 # if CONFIG_ETRAX_SER3_DSR_ON_PB_BIT == -1
724 # ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED
725 # define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1
726 # endif
727 # endif
728 # if CONFIG_ETRAX_SER3_CD_ON_PB_BIT == -1
729 # ifndef CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED
730 # define CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED 1
731 # endif
732 # endif
733 #endif
734
735 #endif /* PORT3 */
736
737
738 #if defined(CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_MIXED) || \
739 defined(CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED) || \
740 defined(CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED) || \
741 defined(CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED)
742 #define CONFIG_ETRAX_SERX_DTR_RI_DSR_CD_MIXED
743 #endif
744
745 #ifdef CONFIG_ETRAX_SERX_DTR_RI_DSR_CD_MIXED
746 /* The pins can be mixed on PA and PB */
747 #define CONTROL_PINS_PORT_NOT_USED(line) \
748 &dummy_ser[line], &dummy_ser[line], \
749 &dummy_ser[line], &dummy_ser[line], \
750 &dummy_ser[line], &dummy_ser[line], \
751 &dummy_ser[line], &dummy_ser[line], \
752 DUMMY_DTR_MASK, DUMMY_RI_MASK, DUMMY_DSR_MASK, DUMMY_CD_MASK
753
754
755 struct control_pins
756 {
757 volatile unsigned char *dtr_port;
758 unsigned char *dtr_shadow;
759 volatile unsigned char *ri_port;
760 unsigned char *ri_shadow;
761 volatile unsigned char *dsr_port;
762 unsigned char *dsr_shadow;
763 volatile unsigned char *cd_port;
764 unsigned char *cd_shadow;
765
766 unsigned char dtr_mask;
767 unsigned char ri_mask;
768 unsigned char dsr_mask;
769 unsigned char cd_mask;
770 };
771
772 static const struct control_pins e100_modem_pins[NR_PORTS] =
773 {
774 /* Ser 0 */
775 {
776 #ifdef CONFIG_ETRAX_SERIAL_PORT0
777 E100_STRUCT_PORT(0,DTR), E100_STRUCT_SHADOW(0,DTR),
778 E100_STRUCT_PORT(0,RI), E100_STRUCT_SHADOW(0,RI),
779 E100_STRUCT_PORT(0,DSR), E100_STRUCT_SHADOW(0,DSR),
780 E100_STRUCT_PORT(0,CD), E100_STRUCT_SHADOW(0,CD),
781 E100_STRUCT_MASK(0,DTR),
782 E100_STRUCT_MASK(0,RI),
783 E100_STRUCT_MASK(0,DSR),
784 E100_STRUCT_MASK(0,CD)
785 #else
786 CONTROL_PINS_PORT_NOT_USED(0)
787 #endif
788 },
789
790 /* Ser 1 */
791 {
792 #ifdef CONFIG_ETRAX_SERIAL_PORT1
793 E100_STRUCT_PORT(1,DTR), E100_STRUCT_SHADOW(1,DTR),
794 E100_STRUCT_PORT(1,RI), E100_STRUCT_SHADOW(1,RI),
795 E100_STRUCT_PORT(1,DSR), E100_STRUCT_SHADOW(1,DSR),
796 E100_STRUCT_PORT(1,CD), E100_STRUCT_SHADOW(1,CD),
797 E100_STRUCT_MASK(1,DTR),
798 E100_STRUCT_MASK(1,RI),
799 E100_STRUCT_MASK(1,DSR),
800 E100_STRUCT_MASK(1,CD)
801 #else
802 CONTROL_PINS_PORT_NOT_USED(1)
803 #endif
804 },
805
806 /* Ser 2 */
807 {
808 #ifdef CONFIG_ETRAX_SERIAL_PORT2
809 E100_STRUCT_PORT(2,DTR), E100_STRUCT_SHADOW(2,DTR),
810 E100_STRUCT_PORT(2,RI), E100_STRUCT_SHADOW(2,RI),
811 E100_STRUCT_PORT(2,DSR), E100_STRUCT_SHADOW(2,DSR),
812 E100_STRUCT_PORT(2,CD), E100_STRUCT_SHADOW(2,CD),
813 E100_STRUCT_MASK(2,DTR),
814 E100_STRUCT_MASK(2,RI),
815 E100_STRUCT_MASK(2,DSR),
816 E100_STRUCT_MASK(2,CD)
817 #else
818 CONTROL_PINS_PORT_NOT_USED(2)
819 #endif
820 },
821
822 /* Ser 3 */
823 {
824 #ifdef CONFIG_ETRAX_SERIAL_PORT3
825 E100_STRUCT_PORT(3,DTR), E100_STRUCT_SHADOW(3,DTR),
826 E100_STRUCT_PORT(3,RI), E100_STRUCT_SHADOW(3,RI),
827 E100_STRUCT_PORT(3,DSR), E100_STRUCT_SHADOW(3,DSR),
828 E100_STRUCT_PORT(3,CD), E100_STRUCT_SHADOW(3,CD),
829 E100_STRUCT_MASK(3,DTR),
830 E100_STRUCT_MASK(3,RI),
831 E100_STRUCT_MASK(3,DSR),
832 E100_STRUCT_MASK(3,CD)
833 #else
834 CONTROL_PINS_PORT_NOT_USED(3)
835 #endif
836 }
837 };
838 #else /* CONFIG_ETRAX_SERX_DTR_RI_DSR_CD_MIXED */
839
840 /* All pins are on either PA or PB for each serial port */
841 #define CONTROL_PINS_PORT_NOT_USED(line) \
842 &dummy_ser[line], &dummy_ser[line], \
843 DUMMY_DTR_MASK, DUMMY_RI_MASK, DUMMY_DSR_MASK, DUMMY_CD_MASK
844
845
846 struct control_pins
847 {
848 volatile unsigned char *port;
849 unsigned char *shadow;
850
851 unsigned char dtr_mask;
852 unsigned char ri_mask;
853 unsigned char dsr_mask;
854 unsigned char cd_mask;
855 };
856
857 #define dtr_port port
858 #define dtr_shadow shadow
859 #define ri_port port
860 #define ri_shadow shadow
861 #define dsr_port port
862 #define dsr_shadow shadow
863 #define cd_port port
864 #define cd_shadow shadow
865
866 static const struct control_pins e100_modem_pins[NR_PORTS] =
867 {
868 /* Ser 0 */
869 {
870 #ifdef CONFIG_ETRAX_SERIAL_PORT0
871 E100_STRUCT_PORT(0,DTR), E100_STRUCT_SHADOW(0,DTR),
872 E100_STRUCT_MASK(0,DTR),
873 E100_STRUCT_MASK(0,RI),
874 E100_STRUCT_MASK(0,DSR),
875 E100_STRUCT_MASK(0,CD)
876 #else
877 CONTROL_PINS_PORT_NOT_USED(0)
878 #endif
879 },
880
881 /* Ser 1 */
882 {
883 #ifdef CONFIG_ETRAX_SERIAL_PORT1
884 E100_STRUCT_PORT(1,DTR), E100_STRUCT_SHADOW(1,DTR),
885 E100_STRUCT_MASK(1,DTR),
886 E100_STRUCT_MASK(1,RI),
887 E100_STRUCT_MASK(1,DSR),
888 E100_STRUCT_MASK(1,CD)
889 #else
890 CONTROL_PINS_PORT_NOT_USED(1)
891 #endif
892 },
893
894 /* Ser 2 */
895 {
896 #ifdef CONFIG_ETRAX_SERIAL_PORT2
897 E100_STRUCT_PORT(2,DTR), E100_STRUCT_SHADOW(2,DTR),
898 E100_STRUCT_MASK(2,DTR),
899 E100_STRUCT_MASK(2,RI),
900 E100_STRUCT_MASK(2,DSR),
901 E100_STRUCT_MASK(2,CD)
902 #else
903 CONTROL_PINS_PORT_NOT_USED(2)
904 #endif
905 },
906
907 /* Ser 3 */
908 {
909 #ifdef CONFIG_ETRAX_SERIAL_PORT3
910 E100_STRUCT_PORT(3,DTR), E100_STRUCT_SHADOW(3,DTR),
911 E100_STRUCT_MASK(3,DTR),
912 E100_STRUCT_MASK(3,RI),
913 E100_STRUCT_MASK(3,DSR),
914 E100_STRUCT_MASK(3,CD)
915 #else
916 CONTROL_PINS_PORT_NOT_USED(3)
917 #endif
918 }
919 };
920 #endif /* !CONFIG_ETRAX_SERX_DTR_RI_DSR_CD_MIXED */
921
922 #define E100_RTS_MASK 0x20
923 #define E100_CTS_MASK 0x40
924
925 /* All serial port signals are active low:
926 * active = 0 -> 3.3V to RS-232 driver -> -12V on RS-232 level
927 * inactive = 1 -> 0V to RS-232 driver -> +12V on RS-232 level
928 *
929 * These macros returns the pin value: 0=0V, >=1 = 3.3V on ETRAX chip
930 */
931
932 /* Output */
933 #define E100_RTS_GET(info) ((info)->rx_ctrl & E100_RTS_MASK)
934 /* Input */
935 #define E100_CTS_GET(info) ((info)->ioport[REG_STATUS] & E100_CTS_MASK)
936
937 /* These are typically PA or PB and 0 means 0V, 1 means 3.3V */
938 /* Is an output */
939 #define E100_DTR_GET(info) ((*e100_modem_pins[(info)->line].dtr_shadow) & e100_modem_pins[(info)->line].dtr_mask)
940
941 /* Normally inputs */
942 #define E100_RI_GET(info) ((*e100_modem_pins[(info)->line].ri_port) & e100_modem_pins[(info)->line].ri_mask)
943 #define E100_CD_GET(info) ((*e100_modem_pins[(info)->line].cd_port) & e100_modem_pins[(info)->line].cd_mask)
944
945 /* Input */
946 #define E100_DSR_GET(info) ((*e100_modem_pins[(info)->line].dsr_port) & e100_modem_pins[(info)->line].dsr_mask)
947
948 /* Calculate the chartime depending on baudrate, numbor of bits etc. */
949 static void update_char_time(struct e100_serial * info)
950 {
951 tcflag_t cflags = info->port.tty->termios.c_cflag;
952 int bits;
953
954 /* calc. number of bits / data byte */
955 /* databits + startbit and 1 stopbit */
956 if ((cflags & CSIZE) == CS7)
957 bits = 9;
958 else
959 bits = 10;
960
961 if (cflags & CSTOPB) /* 2 stopbits ? */
962 bits++;
963
964 if (cflags & PARENB) /* parity bit ? */
965 bits++;
966
967 /* calc timeout */
968 info->char_time_usec = ((bits * 1000000) / info->baud) + 1;
969 info->flush_time_usec = 4*info->char_time_usec;
970 if (info->flush_time_usec < MIN_FLUSH_TIME_USEC)
971 info->flush_time_usec = MIN_FLUSH_TIME_USEC;
972
973 }
974
975 /*
976 * This function maps from the Bxxxx defines in asm/termbits.h into real
977 * baud rates.
978 */
979
980 static int
981 cflag_to_baud(unsigned int cflag)
982 {
983 static int baud_table[] = {
984 0, 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400,
985 4800, 9600, 19200, 38400 };
986
987 static int ext_baud_table[] = {
988 0, 57600, 115200, 230400, 460800, 921600, 1843200, 6250000,
989 0, 0, 0, 0, 0, 0, 0, 0 };
990
991 if (cflag & CBAUDEX)
992 return ext_baud_table[(cflag & CBAUD) & ~CBAUDEX];
993 else
994 return baud_table[cflag & CBAUD];
995 }
996
997 /* and this maps to an etrax100 hardware baud constant */
998
999 static unsigned char
1000 cflag_to_etrax_baud(unsigned int cflag)
1001 {
1002 char retval;
1003
1004 static char baud_table[] = {
1005 -1, -1, -1, -1, -1, -1, -1, 0, 1, 2, -1, 3, 4, 5, 6, 7 };
1006
1007 static char ext_baud_table[] = {
1008 -1, 8, 9, 10, 11, 12, 13, 14, -1, -1, -1, -1, -1, -1, -1, -1 };
1009
1010 if (cflag & CBAUDEX)
1011 retval = ext_baud_table[(cflag & CBAUD) & ~CBAUDEX];
1012 else
1013 retval = baud_table[cflag & CBAUD];
1014
1015 if (retval < 0) {
1016 printk(KERN_WARNING "serdriver tried setting invalid baud rate, flags %x.\n", cflag);
1017 retval = 5; /* choose default 9600 instead */
1018 }
1019
1020 return retval | (retval << 4); /* choose same for both TX and RX */
1021 }
1022
1023
1024 /* Various static support functions */
1025
1026 /* Functions to set or clear DTR/RTS on the requested line */
1027 /* It is complicated by the fact that RTS is a serial port register, while
1028 * DTR might not be implemented in the HW at all, and if it is, it can be on
1029 * any general port.
1030 */
1031
1032
1033 static inline void
1034 e100_dtr(struct e100_serial *info, int set)
1035 {
1036 unsigned char mask = e100_modem_pins[info->line].dtr_mask;
1037
1038 #ifdef SERIAL_DEBUG_IO
1039 printk("ser%i dtr %i mask: 0x%02X\n", info->line, set, mask);
1040 printk("ser%i shadow before 0x%02X get: %i\n",
1041 info->line, *e100_modem_pins[info->line].dtr_shadow,
1042 E100_DTR_GET(info));
1043 #endif
1044 /* DTR is active low */
1045 {
1046 unsigned long flags;
1047
1048 local_irq_save(flags);
1049 *e100_modem_pins[info->line].dtr_shadow &= ~mask;
1050 *e100_modem_pins[info->line].dtr_shadow |= (set ? 0 : mask);
1051 *e100_modem_pins[info->line].dtr_port = *e100_modem_pins[info->line].dtr_shadow;
1052 local_irq_restore(flags);
1053 }
1054
1055 #ifdef SERIAL_DEBUG_IO
1056 printk("ser%i shadow after 0x%02X get: %i\n",
1057 info->line, *e100_modem_pins[info->line].dtr_shadow,
1058 E100_DTR_GET(info));
1059 #endif
1060 }
1061
1062 /* set = 0 means 3.3V on the pin, bitvalue: 0=active, 1=inactive
1063 * 0=0V , 1=3.3V
1064 */
1065 static inline void
1066 e100_rts(struct e100_serial *info, int set)
1067 {
1068 unsigned long flags;
1069 local_irq_save(flags);
1070 info->rx_ctrl &= ~E100_RTS_MASK;
1071 info->rx_ctrl |= (set ? 0 : E100_RTS_MASK); /* RTS is active low */
1072 info->ioport[REG_REC_CTRL] = info->rx_ctrl;
1073 local_irq_restore(flags);
1074 #ifdef SERIAL_DEBUG_IO
1075 printk("ser%i rts %i\n", info->line, set);
1076 #endif
1077 }
1078
1079
1080 /* If this behaves as a modem, RI and CD is an output */
1081 static inline void
1082 e100_ri_out(struct e100_serial *info, int set)
1083 {
1084 /* RI is active low */
1085 {
1086 unsigned char mask = e100_modem_pins[info->line].ri_mask;
1087 unsigned long flags;
1088
1089 local_irq_save(flags);
1090 *e100_modem_pins[info->line].ri_shadow &= ~mask;
1091 *e100_modem_pins[info->line].ri_shadow |= (set ? 0 : mask);
1092 *e100_modem_pins[info->line].ri_port = *e100_modem_pins[info->line].ri_shadow;
1093 local_irq_restore(flags);
1094 }
1095 }
1096 static inline void
1097 e100_cd_out(struct e100_serial *info, int set)
1098 {
1099 /* CD is active low */
1100 {
1101 unsigned char mask = e100_modem_pins[info->line].cd_mask;
1102 unsigned long flags;
1103
1104 local_irq_save(flags);
1105 *e100_modem_pins[info->line].cd_shadow &= ~mask;
1106 *e100_modem_pins[info->line].cd_shadow |= (set ? 0 : mask);
1107 *e100_modem_pins[info->line].cd_port = *e100_modem_pins[info->line].cd_shadow;
1108 local_irq_restore(flags);
1109 }
1110 }
1111
1112 static inline void
1113 e100_disable_rx(struct e100_serial *info)
1114 {
1115 /* disable the receiver */
1116 info->ioport[REG_REC_CTRL] =
1117 (info->rx_ctrl &= ~IO_MASK(R_SERIAL0_REC_CTRL, rec_enable));
1118 }
1119
1120 static inline void
1121 e100_enable_rx(struct e100_serial *info)
1122 {
1123 /* enable the receiver */
1124 info->ioport[REG_REC_CTRL] =
1125 (info->rx_ctrl |= IO_MASK(R_SERIAL0_REC_CTRL, rec_enable));
1126 }
1127
1128 /* the rx DMA uses both the dma_descr and the dma_eop interrupts */
1129
1130 static inline void
1131 e100_disable_rxdma_irq(struct e100_serial *info)
1132 {
1133 #ifdef SERIAL_DEBUG_INTR
1134 printk("rxdma_irq(%d): 0\n",info->line);
1135 #endif
1136 DINTR1(DEBUG_LOG(info->line,"IRQ disable_rxdma_irq %i\n", info->line));
1137 *R_IRQ_MASK2_CLR = (info->irq << 2) | (info->irq << 3);
1138 }
1139
1140 static inline void
1141 e100_enable_rxdma_irq(struct e100_serial *info)
1142 {
1143 #ifdef SERIAL_DEBUG_INTR
1144 printk("rxdma_irq(%d): 1\n",info->line);
1145 #endif
1146 DINTR1(DEBUG_LOG(info->line,"IRQ enable_rxdma_irq %i\n", info->line));
1147 *R_IRQ_MASK2_SET = (info->irq << 2) | (info->irq << 3);
1148 }
1149
1150 /* the tx DMA uses only dma_descr interrupt */
1151
1152 static void e100_disable_txdma_irq(struct e100_serial *info)
1153 {
1154 #ifdef SERIAL_DEBUG_INTR
1155 printk("txdma_irq(%d): 0\n",info->line);
1156 #endif
1157 DINTR1(DEBUG_LOG(info->line,"IRQ disable_txdma_irq %i\n", info->line));
1158 *R_IRQ_MASK2_CLR = info->irq;
1159 }
1160
1161 static void e100_enable_txdma_irq(struct e100_serial *info)
1162 {
1163 #ifdef SERIAL_DEBUG_INTR
1164 printk("txdma_irq(%d): 1\n",info->line);
1165 #endif
1166 DINTR1(DEBUG_LOG(info->line,"IRQ enable_txdma_irq %i\n", info->line));
1167 *R_IRQ_MASK2_SET = info->irq;
1168 }
1169
1170 static void e100_disable_txdma_channel(struct e100_serial *info)
1171 {
1172 unsigned long flags;
1173
1174 /* Disable output DMA channel for the serial port in question
1175 * ( set to something other than serialX)
1176 */
1177 local_irq_save(flags);
1178 DFLOW(DEBUG_LOG(info->line, "disable_txdma_channel %i\n", info->line));
1179 if (info->line == 0) {
1180 if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma6)) ==
1181 IO_STATE(R_GEN_CONFIG, dma6, serial0)) {
1182 genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma6);
1183 genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma6, unused);
1184 }
1185 } else if (info->line == 1) {
1186 if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma8)) ==
1187 IO_STATE(R_GEN_CONFIG, dma8, serial1)) {
1188 genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma8);
1189 genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma8, usb);
1190 }
1191 } else if (info->line == 2) {
1192 if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma2)) ==
1193 IO_STATE(R_GEN_CONFIG, dma2, serial2)) {
1194 genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma2);
1195 genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma2, par0);
1196 }
1197 } else if (info->line == 3) {
1198 if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma4)) ==
1199 IO_STATE(R_GEN_CONFIG, dma4, serial3)) {
1200 genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma4);
1201 genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma4, par1);
1202 }
1203 }
1204 *R_GEN_CONFIG = genconfig_shadow;
1205 local_irq_restore(flags);
1206 }
1207
1208
1209 static void e100_enable_txdma_channel(struct e100_serial *info)
1210 {
1211 unsigned long flags;
1212
1213 local_irq_save(flags);
1214 DFLOW(DEBUG_LOG(info->line, "enable_txdma_channel %i\n", info->line));
1215 /* Enable output DMA channel for the serial port in question */
1216 if (info->line == 0) {
1217 genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma6);
1218 genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma6, serial0);
1219 } else if (info->line == 1) {
1220 genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma8);
1221 genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma8, serial1);
1222 } else if (info->line == 2) {
1223 genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma2);
1224 genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma2, serial2);
1225 } else if (info->line == 3) {
1226 genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma4);
1227 genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma4, serial3);
1228 }
1229 *R_GEN_CONFIG = genconfig_shadow;
1230 local_irq_restore(flags);
1231 }
1232
1233 static void e100_disable_rxdma_channel(struct e100_serial *info)
1234 {
1235 unsigned long flags;
1236
1237 /* Disable input DMA channel for the serial port in question
1238 * ( set to something other than serialX)
1239 */
1240 local_irq_save(flags);
1241 if (info->line == 0) {
1242 if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma7)) ==
1243 IO_STATE(R_GEN_CONFIG, dma7, serial0)) {
1244 genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma7);
1245 genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma7, unused);
1246 }
1247 } else if (info->line == 1) {
1248 if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma9)) ==
1249 IO_STATE(R_GEN_CONFIG, dma9, serial1)) {
1250 genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma9);
1251 genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma9, usb);
1252 }
1253 } else if (info->line == 2) {
1254 if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma3)) ==
1255 IO_STATE(R_GEN_CONFIG, dma3, serial2)) {
1256 genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma3);
1257 genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma3, par0);
1258 }
1259 } else if (info->line == 3) {
1260 if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma5)) ==
1261 IO_STATE(R_GEN_CONFIG, dma5, serial3)) {
1262 genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma5);
1263 genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma5, par1);
1264 }
1265 }
1266 *R_GEN_CONFIG = genconfig_shadow;
1267 local_irq_restore(flags);
1268 }
1269
1270
1271 static void e100_enable_rxdma_channel(struct e100_serial *info)
1272 {
1273 unsigned long flags;
1274
1275 local_irq_save(flags);
1276 /* Enable input DMA channel for the serial port in question */
1277 if (info->line == 0) {
1278 genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma7);
1279 genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma7, serial0);
1280 } else if (info->line == 1) {
1281 genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma9);
1282 genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma9, serial1);
1283 } else if (info->line == 2) {
1284 genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma3);
1285 genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma3, serial2);
1286 } else if (info->line == 3) {
1287 genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma5);
1288 genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma5, serial3);
1289 }
1290 *R_GEN_CONFIG = genconfig_shadow;
1291 local_irq_restore(flags);
1292 }
1293
1294 #ifdef SERIAL_HANDLE_EARLY_ERRORS
1295 /* in order to detect and fix errors on the first byte
1296 we have to use the serial interrupts as well. */
1297
1298 static inline void
1299 e100_disable_serial_data_irq(struct e100_serial *info)
1300 {
1301 #ifdef SERIAL_DEBUG_INTR
1302 printk("ser_irq(%d): 0\n",info->line);
1303 #endif
1304 DINTR1(DEBUG_LOG(info->line,"IRQ disable data_irq %i\n", info->line));
1305 *R_IRQ_MASK1_CLR = (1U << (8+2*info->line));
1306 }
1307
1308 static inline void
1309 e100_enable_serial_data_irq(struct e100_serial *info)
1310 {
1311 #ifdef SERIAL_DEBUG_INTR
1312 printk("ser_irq(%d): 1\n",info->line);
1313 printk("**** %d = %d\n",
1314 (8+2*info->line),
1315 (1U << (8+2*info->line)));
1316 #endif
1317 DINTR1(DEBUG_LOG(info->line,"IRQ enable data_irq %i\n", info->line));
1318 *R_IRQ_MASK1_SET = (1U << (8+2*info->line));
1319 }
1320 #endif
1321
1322 static inline void
1323 e100_disable_serial_tx_ready_irq(struct e100_serial *info)
1324 {
1325 #ifdef SERIAL_DEBUG_INTR
1326 printk("ser_tx_irq(%d): 0\n",info->line);
1327 #endif
1328 DINTR1(DEBUG_LOG(info->line,"IRQ disable ready_irq %i\n", info->line));
1329 *R_IRQ_MASK1_CLR = (1U << (8+1+2*info->line));
1330 }
1331
1332 static inline void
1333 e100_enable_serial_tx_ready_irq(struct e100_serial *info)
1334 {
1335 #ifdef SERIAL_DEBUG_INTR
1336 printk("ser_tx_irq(%d): 1\n",info->line);
1337 printk("**** %d = %d\n",
1338 (8+1+2*info->line),
1339 (1U << (8+1+2*info->line)));
1340 #endif
1341 DINTR2(DEBUG_LOG(info->line,"IRQ enable ready_irq %i\n", info->line));
1342 *R_IRQ_MASK1_SET = (1U << (8+1+2*info->line));
1343 }
1344
1345 static inline void e100_enable_rx_irq(struct e100_serial *info)
1346 {
1347 if (info->uses_dma_in)
1348 e100_enable_rxdma_irq(info);
1349 else
1350 e100_enable_serial_data_irq(info);
1351 }
1352 static inline void e100_disable_rx_irq(struct e100_serial *info)
1353 {
1354 if (info->uses_dma_in)
1355 e100_disable_rxdma_irq(info);
1356 else
1357 e100_disable_serial_data_irq(info);
1358 }
1359
1360 #if defined(CONFIG_ETRAX_RS485)
1361 /* Enable RS-485 mode on selected port. This is UGLY. */
1362 static int
1363 e100_enable_rs485(struct tty_struct *tty, struct serial_rs485 *r)
1364 {
1365 struct e100_serial * info = (struct e100_serial *)tty->driver_data;
1366
1367 #if defined(CONFIG_ETRAX_RS485_ON_PA)
1368 *R_PORT_PA_DATA = port_pa_data_shadow |= (1 << rs485_pa_bit);
1369 #endif
1370 #if defined(CONFIG_ETRAX_RS485_ON_PORT_G)
1371 REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
1372 rs485_port_g_bit, 1);
1373 #endif
1374 #if defined(CONFIG_ETRAX_RS485_LTC1387)
1375 REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
1376 CONFIG_ETRAX_RS485_LTC1387_DXEN_PORT_G_BIT, 1);
1377 REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
1378 CONFIG_ETRAX_RS485_LTC1387_RXEN_PORT_G_BIT, 1);
1379 #endif
1380
1381 info->rs485 = *r;
1382
1383 /* Maximum delay before RTS equal to 1000 */
1384 if (info->rs485.delay_rts_before_send >= 1000)
1385 info->rs485.delay_rts_before_send = 1000;
1386
1387 /* printk("rts: on send = %i, after = %i, enabled = %i",
1388 info->rs485.rts_on_send,
1389 info->rs485.rts_after_sent,
1390 info->rs485.enabled
1391 );
1392 */
1393 return 0;
1394 }
1395
1396 static int
1397 e100_write_rs485(struct tty_struct *tty,
1398 const unsigned char *buf, int count)
1399 {
1400 struct e100_serial * info = (struct e100_serial *)tty->driver_data;
1401 int old_value = (info->rs485.flags) & SER_RS485_ENABLED;
1402
1403 /* rs485 is always implicitly enabled if we're using the ioctl()
1404 * but it doesn't have to be set in the serial_rs485
1405 * (to be backward compatible with old apps)
1406 * So we store, set and restore it.
1407 */
1408 info->rs485.flags |= SER_RS485_ENABLED;
1409 /* rs_write now deals with RS485 if enabled */
1410 count = rs_write(tty, buf, count);
1411 if (!old_value)
1412 info->rs485.flags &= ~(SER_RS485_ENABLED);
1413 return count;
1414 }
1415
1416 #ifdef CONFIG_ETRAX_FAST_TIMER
1417 /* Timer function to toggle RTS when using FAST_TIMER */
1418 static void rs485_toggle_rts_timer_function(unsigned long data)
1419 {
1420 struct e100_serial *info = (struct e100_serial *)data;
1421
1422 fast_timers_rs485[info->line].function = NULL;
1423 e100_rts(info, (info->rs485.flags & SER_RS485_RTS_AFTER_SEND));
1424 #if defined(CONFIG_ETRAX_RS485_DISABLE_RECEIVER)
1425 e100_enable_rx(info);
1426 e100_enable_rx_irq(info);
1427 #endif
1428 }
1429 #endif
1430 #endif /* CONFIG_ETRAX_RS485 */
1431
1432 /*
1433 * ------------------------------------------------------------
1434 * rs_stop() and rs_start()
1435 *
1436 * This routines are called before setting or resetting tty->stopped.
1437 * They enable or disable transmitter using the XOFF registers, as necessary.
1438 * ------------------------------------------------------------
1439 */
1440
1441 static void
1442 rs_stop(struct tty_struct *tty)
1443 {
1444 struct e100_serial *info = (struct e100_serial *)tty->driver_data;
1445 if (info) {
1446 unsigned long flags;
1447 unsigned long xoff;
1448
1449 local_irq_save(flags);
1450 DFLOW(DEBUG_LOG(info->line, "XOFF rs_stop xmit %i\n",
1451 CIRC_CNT(info->xmit.head,
1452 info->xmit.tail,SERIAL_XMIT_SIZE)));
1453
1454 xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char,
1455 STOP_CHAR(info->port.tty));
1456 xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, stop);
1457 if (tty->termios.c_iflag & IXON ) {
1458 xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable);
1459 }
1460
1461 *((unsigned long *)&info->ioport[REG_XOFF]) = xoff;
1462 local_irq_restore(flags);
1463 }
1464 }
1465
1466 static void
1467 rs_start(struct tty_struct *tty)
1468 {
1469 struct e100_serial *info = (struct e100_serial *)tty->driver_data;
1470 if (info) {
1471 unsigned long flags;
1472 unsigned long xoff;
1473
1474 local_irq_save(flags);
1475 DFLOW(DEBUG_LOG(info->line, "XOFF rs_start xmit %i\n",
1476 CIRC_CNT(info->xmit.head,
1477 info->xmit.tail,SERIAL_XMIT_SIZE)));
1478 xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char, STOP_CHAR(tty));
1479 xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, enable);
1480 if (tty->termios.c_iflag & IXON ) {
1481 xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable);
1482 }
1483
1484 *((unsigned long *)&info->ioport[REG_XOFF]) = xoff;
1485 if (!info->uses_dma_out &&
1486 info->xmit.head != info->xmit.tail && info->xmit.buf)
1487 e100_enable_serial_tx_ready_irq(info);
1488
1489 local_irq_restore(flags);
1490 }
1491 }
1492
1493 /*
1494 * ----------------------------------------------------------------------
1495 *
1496 * Here starts the interrupt handling routines. All of the following
1497 * subroutines are declared as inline and are folded into
1498 * rs_interrupt(). They were separated out for readability's sake.
1499 *
1500 * Note: rs_interrupt() is a "fast" interrupt, which means that it
1501 * runs with interrupts turned off. People who may want to modify
1502 * rs_interrupt() should try to keep the interrupt handler as fast as
1503 * possible. After you are done making modifications, it is not a bad
1504 * idea to do:
1505 *
1506 * gcc -S -DKERNEL -Wall -Wstrict-prototypes -O6 -fomit-frame-pointer serial.c
1507 *
1508 * and look at the resulting assemble code in serial.s.
1509 *
1510 * - Ted Ts'o (tytso@mit.edu), 7-Mar-93
1511 * -----------------------------------------------------------------------
1512 */
1513
1514 /*
1515 * This routine is used by the interrupt handler to schedule
1516 * processing in the software interrupt portion of the driver.
1517 */
1518 static void rs_sched_event(struct e100_serial *info, int event)
1519 {
1520 if (info->event & (1 << event))
1521 return;
1522 info->event |= 1 << event;
1523 schedule_work(&info->work);
1524 }
1525
1526 /* The output DMA channel is free - use it to send as many chars as possible
1527 * NOTES:
1528 * We don't pay attention to info->x_char, which means if the TTY wants to
1529 * use XON/XOFF it will set info->x_char but we won't send any X char!
1530 *
1531 * To implement this, we'd just start a DMA send of 1 byte pointing at a
1532 * buffer containing the X char, and skip updating xmit. We'd also have to
1533 * check if the last sent char was the X char when we enter this function
1534 * the next time, to avoid updating xmit with the sent X value.
1535 */
1536
1537 static void
1538 transmit_chars_dma(struct e100_serial *info)
1539 {
1540 unsigned int c, sentl;
1541 struct etrax_dma_descr *descr;
1542
1543 /* acknowledge both dma_descr and dma_eop irq in R_DMA_CHx_CLR_INTR */
1544 *info->oclrintradr =
1545 IO_STATE(R_DMA_CH6_CLR_INTR, clr_descr, do) |
1546 IO_STATE(R_DMA_CH6_CLR_INTR, clr_eop, do);
1547
1548 #ifdef SERIAL_DEBUG_INTR
1549 if (info->line == SERIAL_DEBUG_LINE)
1550 printk("tc\n");
1551 #endif
1552 if (!info->tr_running) {
1553 /* weirdo... we shouldn't get here! */
1554 printk(KERN_WARNING "Achtung: transmit_chars_dma with !tr_running\n");
1555 return;
1556 }
1557
1558 descr = &info->tr_descr;
1559
1560 /* first get the amount of bytes sent during the last DMA transfer,
1561 and update xmit accordingly */
1562
1563 /* if the stop bit was not set, all data has been sent */
1564 if (!(descr->status & d_stop)) {
1565 sentl = descr->sw_len;
1566 } else
1567 /* otherwise we find the amount of data sent here */
1568 sentl = descr->hw_len;
1569
1570 DFLOW(DEBUG_LOG(info->line, "TX %i done\n", sentl));
1571
1572 /* update stats */
1573 info->icount.tx += sentl;
1574
1575 /* update xmit buffer */
1576 info->xmit.tail = (info->xmit.tail + sentl) & (SERIAL_XMIT_SIZE - 1);
1577
1578 /* if there is only a few chars left in the buf, wake up the blocked
1579 write if any */
1580 if (CIRC_CNT(info->xmit.head,
1581 info->xmit.tail,
1582 SERIAL_XMIT_SIZE) < WAKEUP_CHARS)
1583 rs_sched_event(info, RS_EVENT_WRITE_WAKEUP);
1584
1585 /* find out the largest amount of consecutive bytes we want to send now */
1586
1587 c = CIRC_CNT_TO_END(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE);
1588
1589 /* Don't send all in one DMA transfer - divide it so we wake up
1590 * application before all is sent
1591 */
1592
1593 if (c >= 4*WAKEUP_CHARS)
1594 c = c/2;
1595
1596 if (c <= 0) {
1597 /* our job here is done, don't schedule any new DMA transfer */
1598 info->tr_running = 0;
1599
1600 #if defined(CONFIG_ETRAX_RS485) && defined(CONFIG_ETRAX_FAST_TIMER)
1601 if (info->rs485.flags & SER_RS485_ENABLED) {
1602 /* Set a short timer to toggle RTS */
1603 start_one_shot_timer(&fast_timers_rs485[info->line],
1604 rs485_toggle_rts_timer_function,
1605 (unsigned long)info,
1606 info->char_time_usec*2,
1607 "RS-485");
1608 }
1609 #endif /* RS485 */
1610 return;
1611 }
1612
1613 /* ok we can schedule a dma send of c chars starting at info->xmit.tail */
1614 /* set up the descriptor correctly for output */
1615 DFLOW(DEBUG_LOG(info->line, "TX %i\n", c));
1616 descr->ctrl = d_int | d_eol | d_wait; /* Wait needed for tty_wait_until_sent() */
1617 descr->sw_len = c;
1618 descr->buf = virt_to_phys(info->xmit.buf + info->xmit.tail);
1619 descr->status = 0;
1620
1621 *info->ofirstadr = virt_to_phys(descr); /* write to R_DMAx_FIRST */
1622 *info->ocmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, start);
1623
1624 /* DMA is now running (hopefully) */
1625 } /* transmit_chars_dma */
1626
1627 static void
1628 start_transmit(struct e100_serial *info)
1629 {
1630 #if 0
1631 if (info->line == SERIAL_DEBUG_LINE)
1632 printk("x\n");
1633 #endif
1634
1635 info->tr_descr.sw_len = 0;
1636 info->tr_descr.hw_len = 0;
1637 info->tr_descr.status = 0;
1638 info->tr_running = 1;
1639 if (info->uses_dma_out)
1640 transmit_chars_dma(info);
1641 else
1642 e100_enable_serial_tx_ready_irq(info);
1643 } /* start_transmit */
1644
1645 #ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER
1646 static int serial_fast_timer_started = 0;
1647 static int serial_fast_timer_expired = 0;
1648 static void flush_timeout_function(unsigned long data);
1649 #define START_FLUSH_FAST_TIMER_TIME(info, string, usec) {\
1650 unsigned long timer_flags; \
1651 local_irq_save(timer_flags); \
1652 if (fast_timers[info->line].function == NULL) { \
1653 serial_fast_timer_started++; \
1654 TIMERD(DEBUG_LOG(info->line, "start_timer %i ", info->line)); \
1655 TIMERD(DEBUG_LOG(info->line, "num started: %i\n", serial_fast_timer_started)); \
1656 start_one_shot_timer(&fast_timers[info->line], \
1657 flush_timeout_function, \
1658 (unsigned long)info, \
1659 (usec), \
1660 string); \
1661 } \
1662 else { \
1663 TIMERD(DEBUG_LOG(info->line, "timer %i already running\n", info->line)); \
1664 } \
1665 local_irq_restore(timer_flags); \
1666 }
1667 #define START_FLUSH_FAST_TIMER(info, string) START_FLUSH_FAST_TIMER_TIME(info, string, info->flush_time_usec)
1668
1669 #else
1670 #define START_FLUSH_FAST_TIMER_TIME(info, string, usec)
1671 #define START_FLUSH_FAST_TIMER(info, string)
1672 #endif
1673
1674 static struct etrax_recv_buffer *
1675 alloc_recv_buffer(unsigned int size)
1676 {
1677 struct etrax_recv_buffer *buffer;
1678
1679 if (!(buffer = kmalloc(sizeof *buffer + size, GFP_ATOMIC)))
1680 return NULL;
1681
1682 buffer->next = NULL;
1683 buffer->length = 0;
1684 buffer->error = TTY_NORMAL;
1685
1686 return buffer;
1687 }
1688
1689 static void
1690 append_recv_buffer(struct e100_serial *info, struct etrax_recv_buffer *buffer)
1691 {
1692 unsigned long flags;
1693
1694 local_irq_save(flags);
1695
1696 if (!info->first_recv_buffer)
1697 info->first_recv_buffer = buffer;
1698 else
1699 info->last_recv_buffer->next = buffer;
1700
1701 info->last_recv_buffer = buffer;
1702
1703 info->recv_cnt += buffer->length;
1704 if (info->recv_cnt > info->max_recv_cnt)
1705 info->max_recv_cnt = info->recv_cnt;
1706
1707 local_irq_restore(flags);
1708 }
1709
1710 static int
1711 add_char_and_flag(struct e100_serial *info, unsigned char data, unsigned char flag)
1712 {
1713 struct etrax_recv_buffer *buffer;
1714 if (info->uses_dma_in) {
1715 if (!(buffer = alloc_recv_buffer(4)))
1716 return 0;
1717
1718 buffer->length = 1;
1719 buffer->error = flag;
1720 buffer->buffer[0] = data;
1721
1722 append_recv_buffer(info, buffer);
1723
1724 info->icount.rx++;
1725 } else {
1726 tty_insert_flip_char(&info->port, data, flag);
1727 info->icount.rx++;
1728 }
1729
1730 return 1;
1731 }
1732
1733 static unsigned int handle_descr_data(struct e100_serial *info,
1734 struct etrax_dma_descr *descr,
1735 unsigned int recvl)
1736 {
1737 struct etrax_recv_buffer *buffer = phys_to_virt(descr->buf) - sizeof *buffer;
1738
1739 if (info->recv_cnt + recvl > 65536) {
1740 printk(KERN_WARNING
1741 "%s: Too much pending incoming serial data! Dropping %u bytes.\n", __func__, recvl);
1742 return 0;
1743 }
1744
1745 buffer->length = recvl;
1746
1747 if (info->errorcode == ERRCODE_SET_BREAK)
1748 buffer->error = TTY_BREAK;
1749 info->errorcode = 0;
1750
1751 append_recv_buffer(info, buffer);
1752
1753 if (!(buffer = alloc_recv_buffer(SERIAL_DESCR_BUF_SIZE)))
1754 panic("%s: Failed to allocate memory for receive buffer!\n", __func__);
1755
1756 descr->buf = virt_to_phys(buffer->buffer);
1757
1758 return recvl;
1759 }
1760
1761 static unsigned int handle_all_descr_data(struct e100_serial *info)
1762 {
1763 struct etrax_dma_descr *descr;
1764 unsigned int recvl;
1765 unsigned int ret = 0;
1766
1767 while (1)
1768 {
1769 descr = &info->rec_descr[info->cur_rec_descr];
1770
1771 if (descr == phys_to_virt(*info->idescradr))
1772 break;
1773
1774 if (++info->cur_rec_descr == SERIAL_RECV_DESCRIPTORS)
1775 info->cur_rec_descr = 0;
1776
1777 /* find out how many bytes were read */
1778
1779 /* if the eop bit was not set, all data has been received */
1780 if (!(descr->status & d_eop)) {
1781 recvl = descr->sw_len;
1782 } else {
1783 /* otherwise we find the amount of data received here */
1784 recvl = descr->hw_len;
1785 }
1786
1787 /* Reset the status information */
1788 descr->status = 0;
1789
1790 DFLOW( DEBUG_LOG(info->line, "RX %lu\n", recvl);
1791 if (info->port.tty->stopped) {
1792 unsigned char *buf = phys_to_virt(descr->buf);
1793 DEBUG_LOG(info->line, "rx 0x%02X\n", buf[0]);
1794 DEBUG_LOG(info->line, "rx 0x%02X\n", buf[1]);
1795 DEBUG_LOG(info->line, "rx 0x%02X\n", buf[2]);
1796 }
1797 );
1798
1799 /* update stats */
1800 info->icount.rx += recvl;
1801
1802 ret += handle_descr_data(info, descr, recvl);
1803 }
1804
1805 return ret;
1806 }
1807
1808 static void receive_chars_dma(struct e100_serial *info)
1809 {
1810 struct tty_struct *tty;
1811 unsigned char rstat;
1812
1813 /* Acknowledge both dma_descr and dma_eop irq in R_DMA_CHx_CLR_INTR */
1814 *info->iclrintradr =
1815 IO_STATE(R_DMA_CH6_CLR_INTR, clr_descr, do) |
1816 IO_STATE(R_DMA_CH6_CLR_INTR, clr_eop, do);
1817
1818 tty = info->port.tty;
1819 if (!tty) /* Something wrong... */
1820 return;
1821
1822 #ifdef SERIAL_HANDLE_EARLY_ERRORS
1823 if (info->uses_dma_in)
1824 e100_enable_serial_data_irq(info);
1825 #endif
1826
1827 if (info->errorcode == ERRCODE_INSERT_BREAK)
1828 add_char_and_flag(info, '\0', TTY_BREAK);
1829
1830 handle_all_descr_data(info);
1831
1832 /* Read the status register to detect errors */
1833 rstat = info->ioport[REG_STATUS];
1834 if (rstat & IO_MASK(R_SERIAL0_STATUS, xoff_detect) ) {
1835 DFLOW(DEBUG_LOG(info->line, "XOFF detect stat %x\n", rstat));
1836 }
1837
1838 if (rstat & SER_ERROR_MASK) {
1839 /* If we got an error, we must reset it by reading the
1840 * data_in field
1841 */
1842 unsigned char data = info->ioport[REG_DATA];
1843
1844 PROCSTAT(ser_stat[info->line].errors_cnt++);
1845 DEBUG_LOG(info->line, "#dERR: s d 0x%04X\n",
1846 ((rstat & SER_ERROR_MASK) << 8) | data);
1847
1848 if (rstat & SER_PAR_ERR_MASK)
1849 add_char_and_flag(info, data, TTY_PARITY);
1850 else if (rstat & SER_OVERRUN_MASK)
1851 add_char_and_flag(info, data, TTY_OVERRUN);
1852 else if (rstat & SER_FRAMING_ERR_MASK)
1853 add_char_and_flag(info, data, TTY_FRAME);
1854 }
1855
1856 START_FLUSH_FAST_TIMER(info, "receive_chars");
1857
1858 /* Restart the receiving DMA */
1859 *info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, restart);
1860 }
1861
1862 static int start_recv_dma(struct e100_serial *info)
1863 {
1864 struct etrax_dma_descr *descr = info->rec_descr;
1865 struct etrax_recv_buffer *buffer;
1866 int i;
1867
1868 /* Set up the receiving descriptors */
1869 for (i = 0; i < SERIAL_RECV_DESCRIPTORS; i++) {
1870 if (!(buffer = alloc_recv_buffer(SERIAL_DESCR_BUF_SIZE)))
1871 panic("%s: Failed to allocate memory for receive buffer!\n", __func__);
1872
1873 descr[i].ctrl = d_int;
1874 descr[i].buf = virt_to_phys(buffer->buffer);
1875 descr[i].sw_len = SERIAL_DESCR_BUF_SIZE;
1876 descr[i].hw_len = 0;
1877 descr[i].status = 0;
1878 descr[i].next = virt_to_phys(&descr[i+1]);
1879 }
1880
1881 /* Link the last descriptor to the first */
1882 descr[i-1].next = virt_to_phys(&descr[0]);
1883
1884 /* Start with the first descriptor in the list */
1885 info->cur_rec_descr = 0;
1886
1887 /* Start the DMA */
1888 *info->ifirstadr = virt_to_phys(&descr[info->cur_rec_descr]);
1889 *info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, start);
1890
1891 /* Input DMA should be running now */
1892 return 1;
1893 }
1894
1895 static void
1896 start_receive(struct e100_serial *info)
1897 {
1898 if (info->uses_dma_in) {
1899 /* reset the input dma channel to be sure it works */
1900
1901 *info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, reset);
1902 while (IO_EXTRACT(R_DMA_CH6_CMD, cmd, *info->icmdadr) ==
1903 IO_STATE_VALUE(R_DMA_CH6_CMD, cmd, reset));
1904
1905 start_recv_dma(info);
1906 }
1907 }
1908
1909
1910 /* the bits in the MASK2 register are laid out like this:
1911 DMAI_EOP DMAI_DESCR DMAO_EOP DMAO_DESCR
1912 where I is the input channel and O is the output channel for the port.
1913 info->irq is the bit number for the DMAO_DESCR so to check the others we
1914 shift info->irq to the left.
1915 */
1916
1917 /* dma output channel interrupt handler
1918 this interrupt is called from DMA2(ser2), DMA4(ser3), DMA6(ser0) or
1919 DMA8(ser1) when they have finished a descriptor with the intr flag set.
1920 */
1921
1922 static irqreturn_t
1923 tr_interrupt(int irq, void *dev_id)
1924 {
1925 struct e100_serial *info;
1926 unsigned long ireg;
1927 int i;
1928 int handled = 0;
1929
1930 /* find out the line that caused this irq and get it from rs_table */
1931
1932 ireg = *R_IRQ_MASK2_RD; /* get the active irq bits for the dma channels */
1933
1934 for (i = 0; i < NR_PORTS; i++) {
1935 info = rs_table + i;
1936 if (!info->enabled || !info->uses_dma_out)
1937 continue;
1938 /* check for dma_descr (don't need to check for dma_eop in output dma for serial */
1939 if (ireg & info->irq) {
1940 handled = 1;
1941 /* we can send a new dma bunch. make it so. */
1942 DINTR2(DEBUG_LOG(info->line, "tr_interrupt %i\n", i));
1943 /* Read jiffies_usec first,
1944 * we want this time to be as late as possible
1945 */
1946 PROCSTAT(ser_stat[info->line].tx_dma_ints++);
1947 info->last_tx_active_usec = GET_JIFFIES_USEC();
1948 info->last_tx_active = jiffies;
1949 transmit_chars_dma(info);
1950 }
1951
1952 /* FIXME: here we should really check for a change in the
1953 status lines and if so call status_handle(info) */
1954 }
1955 return IRQ_RETVAL(handled);
1956 } /* tr_interrupt */
1957
1958 /* dma input channel interrupt handler */
1959
1960 static irqreturn_t
1961 rec_interrupt(int irq, void *dev_id)
1962 {
1963 struct e100_serial *info;
1964 unsigned long ireg;
1965 int i;
1966 int handled = 0;
1967
1968 /* find out the line that caused this irq and get it from rs_table */
1969
1970 ireg = *R_IRQ_MASK2_RD; /* get the active irq bits for the dma channels */
1971
1972 for (i = 0; i < NR_PORTS; i++) {
1973 info = rs_table + i;
1974 if (!info->enabled || !info->uses_dma_in)
1975 continue;
1976 /* check for both dma_eop and dma_descr for the input dma channel */
1977 if (ireg & ((info->irq << 2) | (info->irq << 3))) {
1978 handled = 1;
1979 /* we have received something */
1980 receive_chars_dma(info);
1981 }
1982
1983 /* FIXME: here we should really check for a change in the
1984 status lines and if so call status_handle(info) */
1985 }
1986 return IRQ_RETVAL(handled);
1987 } /* rec_interrupt */
1988
1989 static int force_eop_if_needed(struct e100_serial *info)
1990 {
1991 /* We check data_avail bit to determine if data has
1992 * arrived since last time
1993 */
1994 unsigned char rstat = info->ioport[REG_STATUS];
1995
1996 /* error or datavail? */
1997 if (rstat & SER_ERROR_MASK) {
1998 /* Some error has occurred. If there has been valid data, an
1999 * EOP interrupt will be made automatically. If no data, the
2000 * normal ser_interrupt should be enabled and handle it.
2001 * So do nothing!
2002 */
2003 DEBUG_LOG(info->line, "timeout err: rstat 0x%03X\n",
2004 rstat | (info->line << 8));
2005 return 0;
2006 }
2007
2008 if (rstat & SER_DATA_AVAIL_MASK) {
2009 /* Ok data, no error, count it */
2010 TIMERD(DEBUG_LOG(info->line, "timeout: rstat 0x%03X\n",
2011 rstat | (info->line << 8)));
2012 /* Read data to clear status flags */
2013 (void)info->ioport[REG_DATA];
2014
2015 info->forced_eop = 0;
2016 START_FLUSH_FAST_TIMER(info, "magic");
2017 return 0;
2018 }
2019
2020 /* hit the timeout, force an EOP for the input
2021 * dma channel if we haven't already
2022 */
2023 if (!info->forced_eop) {
2024 info->forced_eop = 1;
2025 PROCSTAT(ser_stat[info->line].timeout_flush_cnt++);
2026 TIMERD(DEBUG_LOG(info->line, "timeout EOP %i\n", info->line));
2027 FORCE_EOP(info);
2028 }
2029
2030 return 1;
2031 }
2032
2033 static void flush_to_flip_buffer(struct e100_serial *info)
2034 {
2035 struct etrax_recv_buffer *buffer;
2036 unsigned long flags;
2037
2038 local_irq_save(flags);
2039
2040 while ((buffer = info->first_recv_buffer) != NULL) {
2041 unsigned int count = buffer->length;
2042
2043 tty_insert_flip_string(&info->port, buffer->buffer, count);
2044 info->recv_cnt -= count;
2045
2046 if (count == buffer->length) {
2047 info->first_recv_buffer = buffer->next;
2048 kfree(buffer);
2049 } else {
2050 buffer->length -= count;
2051 memmove(buffer->buffer, buffer->buffer + count, buffer->length);
2052 buffer->error = TTY_NORMAL;
2053 }
2054 }
2055
2056 if (!info->first_recv_buffer)
2057 info->last_recv_buffer = NULL;
2058
2059 local_irq_restore(flags);
2060
2061 /* This includes a check for low-latency */
2062 tty_flip_buffer_push(&info->port);
2063 }
2064
2065 static void check_flush_timeout(struct e100_serial *info)
2066 {
2067 /* Flip what we've got (if we can) */
2068 flush_to_flip_buffer(info);
2069
2070 /* We might need to flip later, but not to fast
2071 * since the system is busy processing input... */
2072 if (info->first_recv_buffer)
2073 START_FLUSH_FAST_TIMER_TIME(info, "flip", 2000);
2074
2075 /* Force eop last, since data might have come while we're processing
2076 * and if we started the slow timer above, we won't start a fast
2077 * below.
2078 */
2079 force_eop_if_needed(info);
2080 }
2081
2082 #ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER
2083 static void flush_timeout_function(unsigned long data)
2084 {
2085 struct e100_serial *info = (struct e100_serial *)data;
2086
2087 fast_timers[info->line].function = NULL;
2088 serial_fast_timer_expired++;
2089 TIMERD(DEBUG_LOG(info->line, "flush_timeout %i ", info->line));
2090 TIMERD(DEBUG_LOG(info->line, "num expired: %i\n", serial_fast_timer_expired));
2091 check_flush_timeout(info);
2092 }
2093
2094 #else
2095
2096 /* dma fifo/buffer timeout handler
2097 forces an end-of-packet for the dma input channel if no chars
2098 have been received for CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS/100 s.
2099 */
2100
2101 static struct timer_list flush_timer;
2102
2103 static void
2104 timed_flush_handler(unsigned long ptr)
2105 {
2106 struct e100_serial *info;
2107 int i;
2108
2109 for (i = 0; i < NR_PORTS; i++) {
2110 info = rs_table + i;
2111 if (info->uses_dma_in)
2112 check_flush_timeout(info);
2113 }
2114
2115 /* restart flush timer */
2116 mod_timer(&flush_timer, jiffies + CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS);
2117 }
2118 #endif
2119
2120 #ifdef SERIAL_HANDLE_EARLY_ERRORS
2121
2122 /* If there is an error (ie break) when the DMA is running and
2123 * there are no bytes in the fifo the DMA is stopped and we get no
2124 * eop interrupt. Thus we have to monitor the first bytes on a DMA
2125 * transfer, and if it is without error we can turn the serial
2126 * interrupts off.
2127 */
2128
2129 /*
2130 BREAK handling on ETRAX 100:
2131 ETRAX will generate interrupt although there is no stop bit between the
2132 characters.
2133
2134 Depending on how long the break sequence is, the end of the breaksequence
2135 will look differently:
2136 | indicates start/end of a character.
2137
2138 B= Break character (0x00) with framing error.
2139 E= Error byte with parity error received after B characters.
2140 F= "Faked" valid byte received immediately after B characters.
2141 V= Valid byte
2142
2143 1.
2144 B BL ___________________________ V
2145 .._|__________|__________| |valid data |
2146
2147 Multiple frame errors with data == 0x00 (B),
2148 the timing matches up "perfectly" so no extra ending char is detected.
2149 The RXD pin is 1 in the last interrupt, in that case
2150 we set info->errorcode = ERRCODE_INSERT_BREAK, but we can't really
2151 know if another byte will come and this really is case 2. below
2152 (e.g F=0xFF or 0xFE)
2153 If RXD pin is 0 we can expect another character (see 2. below).
2154
2155
2156 2.
2157
2158 B B E or F__________________..__ V
2159 .._|__________|__________|______ | |valid data
2160 "valid" or
2161 parity error
2162
2163 Multiple frame errors with data == 0x00 (B),
2164 but the part of the break trigs is interpreted as a start bit (and possibly
2165 some 0 bits followed by a number of 1 bits and a stop bit).
2166 Depending on parity settings etc. this last character can be either
2167 a fake "valid" char (F) or have a parity error (E).
2168
2169 If the character is valid it will be put in the buffer,
2170 we set info->errorcode = ERRCODE_SET_BREAK so the receive interrupt
2171 will set the flags so the tty will handle it,
2172 if it's an error byte it will not be put in the buffer
2173 and we set info->errorcode = ERRCODE_INSERT_BREAK.
2174
2175 To distinguish a V byte in 1. from an F byte in 2. we keep a timestamp
2176 of the last faulty char (B) and compares it with the current time:
2177 If the time elapsed time is less then 2*char_time_usec we will assume
2178 it's a faked F char and not a Valid char and set
2179 info->errorcode = ERRCODE_SET_BREAK.
2180
2181 Flaws in the above solution:
2182 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2183 We use the timer to distinguish a F character from a V character,
2184 if a V character is to close after the break we might make the wrong decision.
2185
2186 TODO: The break will be delayed until an F or V character is received.
2187
2188 */
2189
2190 static void handle_ser_rx_interrupt_no_dma(struct e100_serial *info)
2191 {
2192 unsigned long data_read;
2193
2194 /* Read data and status at the same time */
2195 data_read = *((unsigned long *)&info->ioport[REG_DATA_STATUS32]);
2196 more_data:
2197 if (data_read & IO_MASK(R_SERIAL0_READ, xoff_detect) ) {
2198 DFLOW(DEBUG_LOG(info->line, "XOFF detect\n", 0));
2199 }
2200 DINTR2(DEBUG_LOG(info->line, "ser_rx %c\n", IO_EXTRACT(R_SERIAL0_READ, data_in, data_read)));
2201
2202 if (data_read & ( IO_MASK(R_SERIAL0_READ, framing_err) |
2203 IO_MASK(R_SERIAL0_READ, par_err) |
2204 IO_MASK(R_SERIAL0_READ, overrun) )) {
2205 /* An error */
2206 info->last_rx_active_usec = GET_JIFFIES_USEC();
2207 info->last_rx_active = jiffies;
2208 DINTR1(DEBUG_LOG(info->line, "ser_rx err stat_data %04X\n", data_read));
2209 DLOG_INT_TRIG(
2210 if (!log_int_trig1_pos) {
2211 log_int_trig1_pos = log_int_pos;
2212 log_int(rdpc(), 0, 0);
2213 }
2214 );
2215
2216
2217 if ( ((data_read & IO_MASK(R_SERIAL0_READ, data_in)) == 0) &&
2218 (data_read & IO_MASK(R_SERIAL0_READ, framing_err)) ) {
2219 /* Most likely a break, but we get interrupts over and
2220 * over again.
2221 */
2222
2223 if (!info->break_detected_cnt) {
2224 DEBUG_LOG(info->line, "#BRK start\n", 0);
2225 }
2226 if (data_read & IO_MASK(R_SERIAL0_READ, rxd)) {
2227 /* The RX pin is high now, so the break
2228 * must be over, but....
2229 * we can't really know if we will get another
2230 * last byte ending the break or not.
2231 * And we don't know if the byte (if any) will
2232 * have an error or look valid.
2233 */
2234 DEBUG_LOG(info->line, "# BL BRK\n", 0);
2235 info->errorcode = ERRCODE_INSERT_BREAK;
2236 }
2237 info->break_detected_cnt++;
2238 } else {
2239 /* The error does not look like a break, but could be
2240 * the end of one
2241 */
2242 if (info->break_detected_cnt) {
2243 DEBUG_LOG(info->line, "EBRK %i\n", info->break_detected_cnt);
2244 info->errorcode = ERRCODE_INSERT_BREAK;
2245 } else {
2246 unsigned char data = IO_EXTRACT(R_SERIAL0_READ,
2247 data_in, data_read);
2248 char flag = TTY_NORMAL;
2249 if (info->errorcode == ERRCODE_INSERT_BREAK) {
2250 tty_insert_flip_char(&info->port, 0, flag);
2251 info->icount.rx++;
2252 }
2253
2254 if (data_read & IO_MASK(R_SERIAL0_READ, par_err)) {
2255 info->icount.parity++;
2256 flag = TTY_PARITY;
2257 } else if (data_read & IO_MASK(R_SERIAL0_READ, overrun)) {
2258 info->icount.overrun++;
2259 flag = TTY_OVERRUN;
2260 } else if (data_read & IO_MASK(R_SERIAL0_READ, framing_err)) {
2261 info->icount.frame++;
2262 flag = TTY_FRAME;
2263 }
2264 tty_insert_flip_char(&info->port, data, flag);
2265 info->errorcode = 0;
2266 }
2267 info->break_detected_cnt = 0;
2268 }
2269 } else if (data_read & IO_MASK(R_SERIAL0_READ, data_avail)) {
2270 /* No error */
2271 DLOG_INT_TRIG(
2272 if (!log_int_trig1_pos) {
2273 if (log_int_pos >= log_int_size) {
2274 log_int_pos = 0;
2275 }
2276 log_int_trig0_pos = log_int_pos;
2277 log_int(rdpc(), 0, 0);
2278 }
2279 );
2280 tty_insert_flip_char(&info->port,
2281 IO_EXTRACT(R_SERIAL0_READ, data_in, data_read),
2282 TTY_NORMAL);
2283 } else {
2284 DEBUG_LOG(info->line, "ser_rx int but no data_avail %08lX\n", data_read);
2285 }
2286
2287
2288 info->icount.rx++;
2289 data_read = *((unsigned long *)&info->ioport[REG_DATA_STATUS32]);
2290 if (data_read & IO_MASK(R_SERIAL0_READ, data_avail)) {
2291 DEBUG_LOG(info->line, "ser_rx %c in loop\n", IO_EXTRACT(R_SERIAL0_READ, data_in, data_read));
2292 goto more_data;
2293 }
2294
2295 tty_flip_buffer_push(&info->port);
2296 }
2297
2298 static void handle_ser_rx_interrupt(struct e100_serial *info)
2299 {
2300 unsigned char rstat;
2301
2302 #ifdef SERIAL_DEBUG_INTR
2303 printk("Interrupt from serport %d\n", i);
2304 #endif
2305 /* DEBUG_LOG(info->line, "ser_interrupt stat %03X\n", rstat | (i << 8)); */
2306 if (!info->uses_dma_in) {
2307 handle_ser_rx_interrupt_no_dma(info);
2308 return;
2309 }
2310 /* DMA is used */
2311 rstat = info->ioport[REG_STATUS];
2312 if (rstat & IO_MASK(R_SERIAL0_STATUS, xoff_detect) ) {
2313 DFLOW(DEBUG_LOG(info->line, "XOFF detect\n", 0));
2314 }
2315
2316 if (rstat & SER_ERROR_MASK) {
2317 unsigned char data;
2318
2319 info->last_rx_active_usec = GET_JIFFIES_USEC();
2320 info->last_rx_active = jiffies;
2321 /* If we got an error, we must reset it by reading the
2322 * data_in field
2323 */
2324 data = info->ioport[REG_DATA];
2325 DINTR1(DEBUG_LOG(info->line, "ser_rx! %c\n", data));
2326 DINTR1(DEBUG_LOG(info->line, "ser_rx err stat %02X\n", rstat));
2327 if (!data && (rstat & SER_FRAMING_ERR_MASK)) {
2328 /* Most likely a break, but we get interrupts over and
2329 * over again.
2330 */
2331
2332 if (!info->break_detected_cnt) {
2333 DEBUG_LOG(info->line, "#BRK start\n", 0);
2334 }
2335 if (rstat & SER_RXD_MASK) {
2336 /* The RX pin is high now, so the break
2337 * must be over, but....
2338 * we can't really know if we will get another
2339 * last byte ending the break or not.
2340 * And we don't know if the byte (if any) will
2341 * have an error or look valid.
2342 */
2343 DEBUG_LOG(info->line, "# BL BRK\n", 0);
2344 info->errorcode = ERRCODE_INSERT_BREAK;
2345 }
2346 info->break_detected_cnt++;
2347 } else {
2348 /* The error does not look like a break, but could be
2349 * the end of one
2350 */
2351 if (info->break_detected_cnt) {
2352 DEBUG_LOG(info->line, "EBRK %i\n", info->break_detected_cnt);
2353 info->errorcode = ERRCODE_INSERT_BREAK;
2354 } else {
2355 if (info->errorcode == ERRCODE_INSERT_BREAK) {
2356 info->icount.brk++;
2357 add_char_and_flag(info, '\0', TTY_BREAK);
2358 }
2359
2360 if (rstat & SER_PAR_ERR_MASK) {
2361 info->icount.parity++;
2362 add_char_and_flag(info, data, TTY_PARITY);
2363 } else if (rstat & SER_OVERRUN_MASK) {
2364 info->icount.overrun++;
2365 add_char_and_flag(info, data, TTY_OVERRUN);
2366 } else if (rstat & SER_FRAMING_ERR_MASK) {
2367 info->icount.frame++;
2368 add_char_and_flag(info, data, TTY_FRAME);
2369 }
2370
2371 info->errorcode = 0;
2372 }
2373 info->break_detected_cnt = 0;
2374 DEBUG_LOG(info->line, "#iERR s d %04X\n",
2375 ((rstat & SER_ERROR_MASK) << 8) | data);
2376 }
2377 PROCSTAT(ser_stat[info->line].early_errors_cnt++);
2378 } else { /* It was a valid byte, now let the DMA do the rest */
2379 unsigned long curr_time_u = GET_JIFFIES_USEC();
2380 unsigned long curr_time = jiffies;
2381
2382 if (info->break_detected_cnt) {
2383 /* Detect if this character is a new valid char or the
2384 * last char in a break sequence: If LSBits are 0 and
2385 * MSBits are high AND the time is close to the
2386 * previous interrupt we should discard it.
2387 */
2388 long elapsed_usec =
2389 (curr_time - info->last_rx_active) * (1000000/HZ) +
2390 curr_time_u - info->last_rx_active_usec;
2391 if (elapsed_usec < 2*info->char_time_usec) {
2392 DEBUG_LOG(info->line, "FBRK %i\n", info->line);
2393 /* Report as BREAK (error) and let
2394 * receive_chars_dma() handle it
2395 */
2396 info->errorcode = ERRCODE_SET_BREAK;
2397 } else {
2398 DEBUG_LOG(info->line, "Not end of BRK (V)%i\n", info->line);
2399 }
2400 DEBUG_LOG(info->line, "num brk %i\n", info->break_detected_cnt);
2401 }
2402
2403 #ifdef SERIAL_DEBUG_INTR
2404 printk("** OK, disabling ser_interrupts\n");
2405 #endif
2406 e100_disable_serial_data_irq(info);
2407 DINTR2(DEBUG_LOG(info->line, "ser_rx OK %d\n", info->line));
2408 info->break_detected_cnt = 0;
2409
2410 PROCSTAT(ser_stat[info->line].ser_ints_ok_cnt++);
2411 }
2412 /* Restarting the DMA never hurts */
2413 *info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, restart);
2414 START_FLUSH_FAST_TIMER(info, "ser_int");
2415 } /* handle_ser_rx_interrupt */
2416
2417 static void handle_ser_tx_interrupt(struct e100_serial *info)
2418 {
2419 unsigned long flags;
2420
2421 if (info->x_char) {
2422 unsigned char rstat;
2423 DFLOW(DEBUG_LOG(info->line, "tx_int: xchar 0x%02X\n", info->x_char));
2424 local_irq_save(flags);
2425 rstat = info->ioport[REG_STATUS];
2426 DFLOW(DEBUG_LOG(info->line, "stat %x\n", rstat));
2427
2428 info->ioport[REG_TR_DATA] = info->x_char;
2429 info->icount.tx++;
2430 info->x_char = 0;
2431 /* We must enable since it is disabled in ser_interrupt */
2432 e100_enable_serial_tx_ready_irq(info);
2433 local_irq_restore(flags);
2434 return;
2435 }
2436 if (info->uses_dma_out) {
2437 unsigned char rstat;
2438 int i;
2439 /* We only use normal tx interrupt when sending x_char */
2440 DFLOW(DEBUG_LOG(info->line, "tx_int: xchar sent\n", 0));
2441 local_irq_save(flags);
2442 rstat = info->ioport[REG_STATUS];
2443 DFLOW(DEBUG_LOG(info->line, "stat %x\n", rstat));
2444 e100_disable_serial_tx_ready_irq(info);
2445 if (info->port.tty->stopped)
2446 rs_stop(info->port.tty);
2447 /* Enable the DMA channel and tell it to continue */
2448 e100_enable_txdma_channel(info);
2449 /* Wait 12 cycles before doing the DMA command */
2450 for(i = 6; i > 0; i--)
2451 nop();
2452
2453 *info->ocmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, continue);
2454 local_irq_restore(flags);
2455 return;
2456 }
2457 /* Normal char-by-char interrupt */
2458 if (info->xmit.head == info->xmit.tail
2459 || info->port.tty->stopped) {
2460 DFLOW(DEBUG_LOG(info->line, "tx_int: stopped %i\n",
2461 info->port.tty->stopped));
2462 e100_disable_serial_tx_ready_irq(info);
2463 info->tr_running = 0;
2464 return;
2465 }
2466 DINTR2(DEBUG_LOG(info->line, "tx_int %c\n", info->xmit.buf[info->xmit.tail]));
2467 /* Send a byte, rs485 timing is critical so turn of ints */
2468 local_irq_save(flags);
2469 info->ioport[REG_TR_DATA] = info->xmit.buf[info->xmit.tail];
2470 info->xmit.tail = (info->xmit.tail + 1) & (SERIAL_XMIT_SIZE-1);
2471 info->icount.tx++;
2472 if (info->xmit.head == info->xmit.tail) {
2473 #if defined(CONFIG_ETRAX_RS485) && defined(CONFIG_ETRAX_FAST_TIMER)
2474 if (info->rs485.flags & SER_RS485_ENABLED) {
2475 /* Set a short timer to toggle RTS */
2476 start_one_shot_timer(&fast_timers_rs485[info->line],
2477 rs485_toggle_rts_timer_function,
2478 (unsigned long)info,
2479 info->char_time_usec*2,
2480 "RS-485");
2481 }
2482 #endif /* RS485 */
2483 info->last_tx_active_usec = GET_JIFFIES_USEC();
2484 info->last_tx_active = jiffies;
2485 e100_disable_serial_tx_ready_irq(info);
2486 info->tr_running = 0;
2487 DFLOW(DEBUG_LOG(info->line, "tx_int: stop2\n", 0));
2488 } else {
2489 /* We must enable since it is disabled in ser_interrupt */
2490 e100_enable_serial_tx_ready_irq(info);
2491 }
2492 local_irq_restore(flags);
2493
2494 if (CIRC_CNT(info->xmit.head,
2495 info->xmit.tail,
2496 SERIAL_XMIT_SIZE) < WAKEUP_CHARS)
2497 rs_sched_event(info, RS_EVENT_WRITE_WAKEUP);
2498
2499 } /* handle_ser_tx_interrupt */
2500
2501 /* result of time measurements:
2502 * RX duration 54-60 us when doing something, otherwise 6-9 us
2503 * ser_int duration: just sending: 8-15 us normally, up to 73 us
2504 */
2505 static irqreturn_t
2506 ser_interrupt(int irq, void *dev_id)
2507 {
2508 static volatile int tx_started = 0;
2509 struct e100_serial *info;
2510 int i;
2511 unsigned long flags;
2512 unsigned long irq_mask1_rd;
2513 unsigned long data_mask = (1 << (8+2*0)); /* ser0 data_avail */
2514 int handled = 0;
2515 static volatile unsigned long reentered_ready_mask = 0;
2516
2517 local_irq_save(flags);
2518 irq_mask1_rd = *R_IRQ_MASK1_RD;
2519 /* First handle all rx interrupts with ints disabled */
2520 info = rs_table;
2521 irq_mask1_rd &= e100_ser_int_mask;
2522 for (i = 0; i < NR_PORTS; i++) {
2523 /* Which line caused the data irq? */
2524 if (irq_mask1_rd & data_mask) {
2525 handled = 1;
2526 handle_ser_rx_interrupt(info);
2527 }
2528 info += 1;
2529 data_mask <<= 2;
2530 }
2531 /* Handle tx interrupts with interrupts enabled so we
2532 * can take care of new data interrupts while transmitting
2533 * We protect the tx part with the tx_started flag.
2534 * We disable the tr_ready interrupts we are about to handle and
2535 * unblock the serial interrupt so new serial interrupts may come.
2536 *
2537 * If we get a new interrupt:
2538 * - it migth be due to synchronous serial ports.
2539 * - serial irq will be blocked by general irq handler.
2540 * - async data will be handled above (sync will be ignored).
2541 * - tx_started flag will prevent us from trying to send again and
2542 * we will exit fast - no need to unblock serial irq.
2543 * - Next (sync) serial interrupt handler will be runned with
2544 * disabled interrupt due to restore_flags() at end of function,
2545 * so sync handler will not be preempted or reentered.
2546 */
2547 if (!tx_started) {
2548 unsigned long ready_mask;
2549 unsigned long
2550 tx_started = 1;
2551 /* Only the tr_ready interrupts left */
2552 irq_mask1_rd &= (IO_MASK(R_IRQ_MASK1_RD, ser0_ready) |
2553 IO_MASK(R_IRQ_MASK1_RD, ser1_ready) |
2554 IO_MASK(R_IRQ_MASK1_RD, ser2_ready) |
2555 IO_MASK(R_IRQ_MASK1_RD, ser3_ready));
2556 while (irq_mask1_rd) {
2557 /* Disable those we are about to handle */
2558 *R_IRQ_MASK1_CLR = irq_mask1_rd;
2559 /* Unblock the serial interrupt */
2560 *R_VECT_MASK_SET = IO_STATE(R_VECT_MASK_SET, serial, set);
2561
2562 local_irq_enable();
2563 ready_mask = (1 << (8+1+2*0)); /* ser0 tr_ready */
2564 info = rs_table;
2565 for (i = 0; i < NR_PORTS; i++) {
2566 /* Which line caused the ready irq? */
2567 if (irq_mask1_rd & ready_mask) {
2568 handled = 1;
2569 handle_ser_tx_interrupt(info);
2570 }
2571 info += 1;
2572 ready_mask <<= 2;
2573 }
2574 /* handle_ser_tx_interrupt enables tr_ready interrupts */
2575 local_irq_disable();
2576 /* Handle reentered TX interrupt */
2577 irq_mask1_rd = reentered_ready_mask;
2578 }
2579 local_irq_disable();
2580 tx_started = 0;
2581 } else {
2582 unsigned long ready_mask;
2583 ready_mask = irq_mask1_rd & (IO_MASK(R_IRQ_MASK1_RD, ser0_ready) |
2584 IO_MASK(R_IRQ_MASK1_RD, ser1_ready) |
2585 IO_MASK(R_IRQ_MASK1_RD, ser2_ready) |
2586 IO_MASK(R_IRQ_MASK1_RD, ser3_ready));
2587 if (ready_mask) {
2588 reentered_ready_mask |= ready_mask;
2589 /* Disable those we are about to handle */
2590 *R_IRQ_MASK1_CLR = ready_mask;
2591 DFLOW(DEBUG_LOG(SERIAL_DEBUG_LINE, "ser_int reentered with TX %X\n", ready_mask));
2592 }
2593 }
2594
2595 local_irq_restore(flags);
2596 return IRQ_RETVAL(handled);
2597 } /* ser_interrupt */
2598 #endif
2599
2600 /*
2601 * -------------------------------------------------------------------
2602 * Here ends the serial interrupt routines.
2603 * -------------------------------------------------------------------
2604 */
2605
2606 /*
2607 * This routine is used to handle the "bottom half" processing for the
2608 * serial driver, known also the "software interrupt" processing.
2609 * This processing is done at the kernel interrupt level, after the
2610 * rs_interrupt() has returned, BUT WITH INTERRUPTS TURNED ON. This
2611 * is where time-consuming activities which can not be done in the
2612 * interrupt driver proper are done; the interrupt driver schedules
2613 * them using rs_sched_event(), and they get done here.
2614 */
2615 static void
2616 do_softint(struct work_struct *work)
2617 {
2618 struct e100_serial *info;
2619 struct tty_struct *tty;
2620
2621 info = container_of(work, struct e100_serial, work);
2622
2623 tty = info->port.tty;
2624 if (!tty)
2625 return;
2626
2627 if (test_and_clear_bit(RS_EVENT_WRITE_WAKEUP, &info->event))
2628 tty_wakeup(tty);
2629 }
2630
2631 static int
2632 startup(struct e100_serial * info)
2633 {
2634 unsigned long flags;
2635 unsigned long xmit_page;
2636 int i;
2637
2638 xmit_page = get_zeroed_page(GFP_KERNEL);
2639 if (!xmit_page)
2640 return -ENOMEM;
2641
2642 local_irq_save(flags);
2643
2644 /* if it was already initialized, skip this */
2645
2646 if (info->port.flags & ASYNC_INITIALIZED) {
2647 local_irq_restore(flags);
2648 free_page(xmit_page);
2649 return 0;
2650 }
2651
2652 if (info->xmit.buf)
2653 free_page(xmit_page);
2654 else
2655 info->xmit.buf = (unsigned char *) xmit_page;
2656
2657 #ifdef SERIAL_DEBUG_OPEN
2658 printk("starting up ttyS%d (xmit_buf 0x%p)...\n", info->line, info->xmit.buf);
2659 #endif
2660
2661 /*
2662 * Clear the FIFO buffers and disable them
2663 * (they will be reenabled in change_speed())
2664 */
2665
2666 /*
2667 * Reset the DMA channels and make sure their interrupts are cleared
2668 */
2669
2670 if (info->dma_in_enabled) {
2671 info->uses_dma_in = 1;
2672 e100_enable_rxdma_channel(info);
2673
2674 *info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, reset);
2675
2676 /* Wait until reset cycle is complete */
2677 while (IO_EXTRACT(R_DMA_CH6_CMD, cmd, *info->icmdadr) ==
2678 IO_STATE_VALUE(R_DMA_CH6_CMD, cmd, reset));
2679
2680 /* Make sure the irqs are cleared */
2681 *info->iclrintradr =
2682 IO_STATE(R_DMA_CH6_CLR_INTR, clr_descr, do) |
2683 IO_STATE(R_DMA_CH6_CLR_INTR, clr_eop, do);
2684 } else {
2685 e100_disable_rxdma_channel(info);
2686 }
2687
2688 if (info->dma_out_enabled) {
2689 info->uses_dma_out = 1;
2690 e100_enable_txdma_channel(info);
2691 *info->ocmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, reset);
2692
2693 while (IO_EXTRACT(R_DMA_CH6_CMD, cmd, *info->ocmdadr) ==
2694 IO_STATE_VALUE(R_DMA_CH6_CMD, cmd, reset));
2695
2696 /* Make sure the irqs are cleared */
2697 *info->oclrintradr =
2698 IO_STATE(R_DMA_CH6_CLR_INTR, clr_descr, do) |
2699 IO_STATE(R_DMA_CH6_CLR_INTR, clr_eop, do);
2700 } else {
2701 e100_disable_txdma_channel(info);
2702 }
2703
2704 if (info->port.tty)
2705 clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
2706
2707 info->xmit.head = info->xmit.tail = 0;
2708 info->first_recv_buffer = info->last_recv_buffer = NULL;
2709 info->recv_cnt = info->max_recv_cnt = 0;
2710
2711 for (i = 0; i < SERIAL_RECV_DESCRIPTORS; i++)
2712 info->rec_descr[i].buf = 0;
2713
2714 /*
2715 * and set the speed and other flags of the serial port
2716 * this will start the rx/tx as well
2717 */
2718 #ifdef SERIAL_HANDLE_EARLY_ERRORS
2719 e100_enable_serial_data_irq(info);
2720 #endif
2721 change_speed(info);
2722
2723 /* dummy read to reset any serial errors */
2724
2725 (void)info->ioport[REG_DATA];
2726
2727 /* enable the interrupts */
2728 if (info->uses_dma_out)
2729 e100_enable_txdma_irq(info);
2730
2731 e100_enable_rx_irq(info);
2732
2733 info->tr_running = 0; /* to be sure we don't lock up the transmitter */
2734
2735 /* setup the dma input descriptor and start dma */
2736
2737 start_receive(info);
2738
2739 /* for safety, make sure the descriptors last result is 0 bytes written */
2740
2741 info->tr_descr.sw_len = 0;
2742 info->tr_descr.hw_len = 0;
2743 info->tr_descr.status = 0;
2744
2745 /* enable RTS/DTR last */
2746
2747 e100_rts(info, 1);
2748 e100_dtr(info, 1);
2749
2750 info->port.flags |= ASYNC_INITIALIZED;
2751
2752 local_irq_restore(flags);
2753 return 0;
2754 }
2755
2756 /*
2757 * This routine will shutdown a serial port; interrupts are disabled, and
2758 * DTR is dropped if the hangup on close termio flag is on.
2759 */
2760 static void
2761 shutdown(struct e100_serial * info)
2762 {
2763 unsigned long flags;
2764 struct etrax_dma_descr *descr = info->rec_descr;
2765 struct etrax_recv_buffer *buffer;
2766 int i;
2767
2768 /* shut down the transmitter and receiver */
2769 DFLOW(DEBUG_LOG(info->line, "shutdown %i\n", info->line));
2770 e100_disable_rx(info);
2771 info->ioport[REG_TR_CTRL] = (info->tx_ctrl &= ~0x40);
2772
2773 /* disable interrupts, reset dma channels */
2774 if (info->uses_dma_in) {
2775 e100_disable_rxdma_irq(info);
2776 *info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, reset);
2777 info->uses_dma_in = 0;
2778 } else {
2779 e100_disable_serial_data_irq(info);
2780 }
2781
2782 if (info->uses_dma_out) {
2783 e100_disable_txdma_irq(info);
2784 info->tr_running = 0;
2785 *info->ocmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, reset);
2786 info->uses_dma_out = 0;
2787 } else {
2788 e100_disable_serial_tx_ready_irq(info);
2789 info->tr_running = 0;
2790 }
2791
2792 if (!(info->port.flags & ASYNC_INITIALIZED))
2793 return;
2794
2795 #ifdef SERIAL_DEBUG_OPEN
2796 printk("Shutting down serial port %d (irq %d)....\n", info->line,
2797 info->irq);
2798 #endif
2799
2800 local_irq_save(flags);
2801
2802 if (info->xmit.buf) {
2803 free_page((unsigned long)info->xmit.buf);
2804 info->xmit.buf = NULL;
2805 }
2806
2807 for (i = 0; i < SERIAL_RECV_DESCRIPTORS; i++)
2808 if (descr[i].buf) {
2809 buffer = phys_to_virt(descr[i].buf) - sizeof *buffer;
2810 kfree(buffer);
2811 descr[i].buf = 0;
2812 }
2813
2814 if (!info->port.tty || (info->port.tty->termios.c_cflag & HUPCL)) {
2815 /* hang up DTR and RTS if HUPCL is enabled */
2816 e100_dtr(info, 0);
2817 e100_rts(info, 0); /* could check CRTSCTS before doing this */
2818 }
2819
2820 if (info->port.tty)
2821 set_bit(TTY_IO_ERROR, &info->port.tty->flags);
2822
2823 info->port.flags &= ~ASYNC_INITIALIZED;
2824 local_irq_restore(flags);
2825 }
2826
2827
2828 /* change baud rate and other assorted parameters */
2829
2830 static void
2831 change_speed(struct e100_serial *info)
2832 {
2833 unsigned int cflag;
2834 unsigned long xoff;
2835 unsigned long flags;
2836 /* first some safety checks */
2837
2838 if (!info->port.tty)
2839 return;
2840 if (!info->ioport)
2841 return;
2842
2843 cflag = info->port.tty->termios.c_cflag;
2844
2845 /* possibly, the tx/rx should be disabled first to do this safely */
2846
2847 /* change baud-rate and write it to the hardware */
2848 if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST) {
2849 /* Special baudrate */
2850 u32 mask = 0xFF << (info->line*8); /* Each port has 8 bits */
2851 unsigned long alt_source =
2852 IO_STATE(R_ALT_SER_BAUDRATE, ser0_rec, normal) |
2853 IO_STATE(R_ALT_SER_BAUDRATE, ser0_tr, normal);
2854 /* R_ALT_SER_BAUDRATE selects the source */
2855 DBAUD(printk("Custom baudrate: baud_base/divisor %lu/%i\n",
2856 (unsigned long)info->baud_base, info->custom_divisor));
2857 if (info->baud_base == SERIAL_PRESCALE_BASE) {
2858 /* 0, 2-65535 (0=65536) */
2859 u16 divisor = info->custom_divisor;
2860 /* R_SERIAL_PRESCALE (upper 16 bits of R_CLOCK_PRESCALE) */
2861 /* baudrate is 3.125MHz/custom_divisor */
2862 alt_source =
2863 IO_STATE(R_ALT_SER_BAUDRATE, ser0_rec, prescale) |
2864 IO_STATE(R_ALT_SER_BAUDRATE, ser0_tr, prescale);
2865 alt_source = 0x11;
2866 DBAUD(printk("Writing SERIAL_PRESCALE: divisor %i\n", divisor));
2867 *R_SERIAL_PRESCALE = divisor;
2868 info->baud = SERIAL_PRESCALE_BASE/divisor;
2869 }
2870 else
2871 {
2872 /* Bad baudbase, we don't support using timer0
2873 * for baudrate.
2874 */
2875 printk(KERN_WARNING "Bad baud_base/custom_divisor: %lu/%i\n",
2876 (unsigned long)info->baud_base, info->custom_divisor);
2877 }
2878 r_alt_ser_baudrate_shadow &= ~mask;
2879 r_alt_ser_baudrate_shadow |= (alt_source << (info->line*8));
2880 *R_ALT_SER_BAUDRATE = r_alt_ser_baudrate_shadow;
2881 } else {
2882 /* Normal baudrate */
2883 /* Make sure we use normal baudrate */
2884 u32 mask = 0xFF << (info->line*8); /* Each port has 8 bits */
2885 unsigned long alt_source =
2886 IO_STATE(R_ALT_SER_BAUDRATE, ser0_rec, normal) |
2887 IO_STATE(R_ALT_SER_BAUDRATE, ser0_tr, normal);
2888 r_alt_ser_baudrate_shadow &= ~mask;
2889 r_alt_ser_baudrate_shadow |= (alt_source << (info->line*8));
2890 *R_ALT_SER_BAUDRATE = r_alt_ser_baudrate_shadow;
2891
2892 info->baud = cflag_to_baud(cflag);
2893 info->ioport[REG_BAUD] = cflag_to_etrax_baud(cflag);
2894 }
2895
2896 /* start with default settings and then fill in changes */
2897 local_irq_save(flags);
2898 /* 8 bit, no/even parity */
2899 info->rx_ctrl &= ~(IO_MASK(R_SERIAL0_REC_CTRL, rec_bitnr) |
2900 IO_MASK(R_SERIAL0_REC_CTRL, rec_par_en) |
2901 IO_MASK(R_SERIAL0_REC_CTRL, rec_par));
2902
2903 /* 8 bit, no/even parity, 1 stop bit, no cts */
2904 info->tx_ctrl &= ~(IO_MASK(R_SERIAL0_TR_CTRL, tr_bitnr) |
2905 IO_MASK(R_SERIAL0_TR_CTRL, tr_par_en) |
2906 IO_MASK(R_SERIAL0_TR_CTRL, tr_par) |
2907 IO_MASK(R_SERIAL0_TR_CTRL, stop_bits) |
2908 IO_MASK(R_SERIAL0_TR_CTRL, auto_cts));
2909
2910 if ((cflag & CSIZE) == CS7) {
2911 /* set 7 bit mode */
2912 info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, tr_bitnr, tr_7bit);
2913 info->rx_ctrl |= IO_STATE(R_SERIAL0_REC_CTRL, rec_bitnr, rec_7bit);
2914 }
2915
2916 if (cflag & CSTOPB) {
2917 /* set 2 stop bit mode */
2918 info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, stop_bits, two_bits);
2919 }
2920
2921 if (cflag & PARENB) {
2922 /* enable parity */
2923 info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, tr_par_en, enable);
2924 info->rx_ctrl |= IO_STATE(R_SERIAL0_REC_CTRL, rec_par_en, enable);
2925 }
2926
2927 if (cflag & CMSPAR) {
2928 /* enable stick parity, PARODD mean Mark which matches ETRAX */
2929 info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, tr_stick_par, stick);
2930 info->rx_ctrl |= IO_STATE(R_SERIAL0_REC_CTRL, rec_stick_par, stick);
2931 }
2932 if (cflag & PARODD) {
2933 /* set odd parity (or Mark if CMSPAR) */
2934 info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, tr_par, odd);
2935 info->rx_ctrl |= IO_STATE(R_SERIAL0_REC_CTRL, rec_par, odd);
2936 }
2937
2938 if (cflag & CRTSCTS) {
2939 /* enable automatic CTS handling */
2940 DFLOW(DEBUG_LOG(info->line, "FLOW auto_cts enabled\n", 0));
2941 info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, auto_cts, active);
2942 }
2943
2944 /* make sure the tx and rx are enabled */
2945
2946 info->tx_ctrl |= IO_STATE(R_SERIAL0_TR_CTRL, tr_enable, enable);
2947 info->rx_ctrl |= IO_STATE(R_SERIAL0_REC_CTRL, rec_enable, enable);
2948
2949 /* actually write the control regs to the hardware */
2950
2951 info->ioport[REG_TR_CTRL] = info->tx_ctrl;
2952 info->ioport[REG_REC_CTRL] = info->rx_ctrl;
2953 xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char, STOP_CHAR(info->port.tty));
2954 xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, enable);
2955 if (info->port.tty->termios.c_iflag & IXON ) {
2956 DFLOW(DEBUG_LOG(info->line, "FLOW XOFF enabled 0x%02X\n",
2957 STOP_CHAR(info->port.tty)));
2958 xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable);
2959 }
2960
2961 *((unsigned long *)&info->ioport[REG_XOFF]) = xoff;
2962 local_irq_restore(flags);
2963
2964 update_char_time(info);
2965
2966 } /* change_speed */
2967
2968 /* start transmitting chars NOW */
2969
2970 static void
2971 rs_flush_chars(struct tty_struct *tty)
2972 {
2973 struct e100_serial *info = (struct e100_serial *)tty->driver_data;
2974 unsigned long flags;
2975
2976 if (info->tr_running ||
2977 info->xmit.head == info->xmit.tail ||
2978 tty->stopped ||
2979 !info->xmit.buf)
2980 return;
2981
2982 #ifdef SERIAL_DEBUG_FLOW
2983 printk("rs_flush_chars\n");
2984 #endif
2985
2986 /* this protection might not exactly be necessary here */
2987
2988 local_irq_save(flags);
2989 start_transmit(info);
2990 local_irq_restore(flags);
2991 }
2992
2993 static int rs_raw_write(struct tty_struct *tty,
2994 const unsigned char *buf, int count)
2995 {
2996 int c, ret = 0;
2997 struct e100_serial *info = (struct e100_serial *)tty->driver_data;
2998 unsigned long flags;
2999
3000 /* first some sanity checks */
3001
3002 if (!info->xmit.buf)
3003 return 0;
3004
3005 #ifdef SERIAL_DEBUG_DATA
3006 if (info->line == SERIAL_DEBUG_LINE)
3007 printk("rs_raw_write (%d), status %d\n",
3008 count, info->ioport[REG_STATUS]);
3009 #endif
3010
3011 local_save_flags(flags);
3012 DFLOW(DEBUG_LOG(info->line, "write count %i ", count));
3013 DFLOW(DEBUG_LOG(info->line, "ldisc %i\n", tty->ldisc.chars_in_buffer(tty)));
3014
3015
3016 /* The local_irq_disable/restore_flags pairs below are needed
3017 * because the DMA interrupt handler moves the info->xmit values.
3018 * the memcpy needs to be in the critical region unfortunately,
3019 * because we need to read xmit values, memcpy, write xmit values
3020 * in one atomic operation... this could perhaps be avoided by
3021 * more clever design.
3022 */
3023 local_irq_disable();
3024 while (count) {
3025 c = CIRC_SPACE_TO_END(info->xmit.head,
3026 info->xmit.tail,
3027 SERIAL_XMIT_SIZE);
3028
3029 if (count < c)
3030 c = count;
3031 if (c <= 0)
3032 break;
3033
3034 memcpy(info->xmit.buf + info->xmit.head, buf, c);
3035 info->xmit.head = (info->xmit.head + c) &
3036 (SERIAL_XMIT_SIZE-1);
3037 buf += c;
3038 count -= c;
3039 ret += c;
3040 }
3041 local_irq_restore(flags);
3042
3043 /* enable transmitter if not running, unless the tty is stopped
3044 * this does not need IRQ protection since if tr_running == 0
3045 * the IRQ's are not running anyway for this port.
3046 */
3047 DFLOW(DEBUG_LOG(info->line, "write ret %i\n", ret));
3048
3049 if (info->xmit.head != info->xmit.tail &&
3050 !tty->stopped &&
3051 !info->tr_running) {
3052 start_transmit(info);
3053 }
3054
3055 return ret;
3056 } /* raw_raw_write() */
3057
3058 static int
3059 rs_write(struct tty_struct *tty,
3060 const unsigned char *buf, int count)
3061 {
3062 #if defined(CONFIG_ETRAX_RS485)
3063 struct e100_serial *info = (struct e100_serial *)tty->driver_data;
3064
3065 if (info->rs485.flags & SER_RS485_ENABLED)
3066 {
3067 /* If we are in RS-485 mode, we need to toggle RTS and disable
3068 * the receiver before initiating a DMA transfer
3069 */
3070 #ifdef CONFIG_ETRAX_FAST_TIMER
3071 /* Abort any started timer */
3072 fast_timers_rs485[info->line].function = NULL;
3073 del_fast_timer(&fast_timers_rs485[info->line]);
3074 #endif
3075 e100_rts(info, (info->rs485.flags & SER_RS485_RTS_ON_SEND));
3076 #if defined(CONFIG_ETRAX_RS485_DISABLE_RECEIVER)
3077 e100_disable_rx(info);
3078 e100_enable_rx_irq(info);
3079 #endif
3080 if (info->rs485.delay_rts_before_send > 0)
3081 msleep(info->rs485.delay_rts_before_send);
3082 }
3083 #endif /* CONFIG_ETRAX_RS485 */
3084
3085 count = rs_raw_write(tty, buf, count);
3086
3087 #if defined(CONFIG_ETRAX_RS485)
3088 if (info->rs485.flags & SER_RS485_ENABLED)
3089 {
3090 unsigned int val;
3091 /* If we are in RS-485 mode the following has to be done:
3092 * wait until DMA is ready
3093 * wait on transmit shift register
3094 * toggle RTS
3095 * enable the receiver
3096 */
3097
3098 /* Sleep until all sent */
3099 tty_wait_until_sent(tty, 0);
3100 #ifdef CONFIG_ETRAX_FAST_TIMER
3101 /* Now sleep a little more so that shift register is empty */
3102 schedule_usleep(info->char_time_usec * 2);
3103 #endif
3104 /* wait on transmit shift register */
3105 do{
3106 get_lsr_info(info, &val);
3107 }while (!(val & TIOCSER_TEMT));
3108
3109 e100_rts(info, (info->rs485.flags & SER_RS485_RTS_AFTER_SEND));
3110
3111 #if defined(CONFIG_ETRAX_RS485_DISABLE_RECEIVER)
3112 e100_enable_rx(info);
3113 e100_enable_rxdma_irq(info);
3114 #endif
3115 }
3116 #endif /* CONFIG_ETRAX_RS485 */
3117
3118 return count;
3119 } /* rs_write */
3120
3121
3122 /* how much space is available in the xmit buffer? */
3123
3124 static int
3125 rs_write_room(struct tty_struct *tty)
3126 {
3127 struct e100_serial *info = (struct e100_serial *)tty->driver_data;
3128
3129 return CIRC_SPACE(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE);
3130 }
3131
3132 /* How many chars are in the xmit buffer?
3133 * This does not include any chars in the transmitter FIFO.
3134 * Use wait_until_sent for waiting for FIFO drain.
3135 */
3136
3137 static int
3138 rs_chars_in_buffer(struct tty_struct *tty)
3139 {
3140 struct e100_serial *info = (struct e100_serial *)tty->driver_data;
3141
3142 return CIRC_CNT(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE);
3143 }
3144
3145 /* discard everything in the xmit buffer */
3146
3147 static void
3148 rs_flush_buffer(struct tty_struct *tty)
3149 {
3150 struct e100_serial *info = (struct e100_serial *)tty->driver_data;
3151 unsigned long flags;
3152
3153 local_irq_save(flags);
3154 info->xmit.head = info->xmit.tail = 0;
3155 local_irq_restore(flags);
3156
3157 tty_wakeup(tty);
3158 }
3159
3160 /*
3161 * This function is used to send a high-priority XON/XOFF character to
3162 * the device
3163 *
3164 * Since we use DMA we don't check for info->x_char in transmit_chars_dma(),
3165 * but we do it in handle_ser_tx_interrupt().
3166 * We disable DMA channel and enable tx ready interrupt and write the
3167 * character when possible.
3168 */
3169 static void rs_send_xchar(struct tty_struct *tty, char ch)
3170 {
3171 struct e100_serial *info = (struct e100_serial *)tty->driver_data;
3172 unsigned long flags;
3173 local_irq_save(flags);
3174 if (info->uses_dma_out) {
3175 /* Put the DMA on hold and disable the channel */
3176 *info->ocmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, hold);
3177 while (IO_EXTRACT(R_DMA_CH6_CMD, cmd, *info->ocmdadr) !=
3178 IO_STATE_VALUE(R_DMA_CH6_CMD, cmd, hold));
3179 e100_disable_txdma_channel(info);
3180 }
3181
3182 /* Must make sure transmitter is not stopped before we can transmit */
3183 if (tty->stopped)
3184 rs_start(tty);
3185
3186 /* Enable manual transmit interrupt and send from there */
3187 DFLOW(DEBUG_LOG(info->line, "rs_send_xchar 0x%02X\n", ch));
3188 info->x_char = ch;
3189 e100_enable_serial_tx_ready_irq(info);
3190 local_irq_restore(flags);
3191 }
3192
3193 /*
3194 * ------------------------------------------------------------
3195 * rs_throttle()
3196 *
3197 * This routine is called by the upper-layer tty layer to signal that
3198 * incoming characters should be throttled.
3199 * ------------------------------------------------------------
3200 */
3201 static void
3202 rs_throttle(struct tty_struct * tty)
3203 {
3204 struct e100_serial *info = (struct e100_serial *)tty->driver_data;
3205 #ifdef SERIAL_DEBUG_THROTTLE
3206 printk("throttle %s: %lu....\n", tty_name(tty),
3207 (unsigned long)tty->ldisc.chars_in_buffer(tty));
3208 #endif
3209 DFLOW(DEBUG_LOG(info->line,"rs_throttle %lu\n", tty->ldisc.chars_in_buffer(tty)));
3210
3211 /* Do RTS before XOFF since XOFF might take some time */
3212 if (tty->termios.c_cflag & CRTSCTS) {
3213 /* Turn off RTS line */
3214 e100_rts(info, 0);
3215 }
3216 if (I_IXOFF(tty))
3217 rs_send_xchar(tty, STOP_CHAR(tty));
3218
3219 }
3220
3221 static void
3222 rs_unthrottle(struct tty_struct * tty)
3223 {
3224 struct e100_serial *info = (struct e100_serial *)tty->driver_data;
3225 #ifdef SERIAL_DEBUG_THROTTLE
3226 printk("unthrottle %s: %lu....\n", tty_name(tty),
3227 (unsigned long)tty->ldisc.chars_in_buffer(tty));
3228 #endif
3229 DFLOW(DEBUG_LOG(info->line,"rs_unthrottle ldisc %d\n", tty->ldisc.chars_in_buffer(tty)));
3230 DFLOW(DEBUG_LOG(info->line,"rs_unthrottle flip.count: %i\n", tty->flip.count));
3231 /* Do RTS before XOFF since XOFF might take some time */
3232 if (tty->termios.c_cflag & CRTSCTS) {
3233 /* Assert RTS line */
3234 e100_rts(info, 1);
3235 }
3236
3237 if (I_IXOFF(tty)) {
3238 if (info->x_char)
3239 info->x_char = 0;
3240 else
3241 rs_send_xchar(tty, START_CHAR(tty));
3242 }
3243
3244 }
3245
3246 /*
3247 * ------------------------------------------------------------
3248 * rs_ioctl() and friends
3249 * ------------------------------------------------------------
3250 */
3251
3252 static int
3253 get_serial_info(struct e100_serial * info,
3254 struct serial_struct * retinfo)
3255 {
3256 struct serial_struct tmp;
3257
3258 /* this is all probably wrong, there are a lot of fields
3259 * here that we don't have in e100_serial and maybe we
3260 * should set them to something else than 0.
3261 */
3262
3263 if (!retinfo)
3264 return -EFAULT;
3265 memset(&tmp, 0, sizeof(tmp));
3266 tmp.type = info->type;
3267 tmp.line = info->line;
3268 tmp.port = (int)info->ioport;
3269 tmp.irq = info->irq;
3270 tmp.flags = info->port.flags;
3271 tmp.baud_base = info->baud_base;
3272 tmp.close_delay = info->port.close_delay;
3273 tmp.closing_wait = info->port.closing_wait;
3274 tmp.custom_divisor = info->custom_divisor;
3275 if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
3276 return -EFAULT;
3277 return 0;
3278 }
3279
3280 static int
3281 set_serial_info(struct e100_serial *info,
3282 struct serial_struct *new_info)
3283 {
3284 struct serial_struct new_serial;
3285 struct e100_serial old_info;
3286 int retval = 0;
3287
3288 if (copy_from_user(&new_serial, new_info, sizeof(new_serial)))
3289 return -EFAULT;
3290
3291 old_info = *info;
3292
3293 if (!capable(CAP_SYS_ADMIN)) {
3294 if ((new_serial.type != info->type) ||
3295 (new_serial.close_delay != info->port.close_delay) ||
3296 ((new_serial.flags & ~ASYNC_USR_MASK) !=
3297 (info->port.flags & ~ASYNC_USR_MASK)))
3298 return -EPERM;
3299 info->port.flags = ((info->port.flags & ~ASYNC_USR_MASK) |
3300 (new_serial.flags & ASYNC_USR_MASK));
3301 goto check_and_exit;
3302 }
3303
3304 if (info->port.count > 1)
3305 return -EBUSY;
3306
3307 /*
3308 * OK, past this point, all the error checking has been done.
3309 * At this point, we start making changes.....
3310 */
3311
3312 info->baud_base = new_serial.baud_base;
3313 info->port.flags = ((info->port.flags & ~ASYNC_FLAGS) |
3314 (new_serial.flags & ASYNC_FLAGS));
3315 info->custom_divisor = new_serial.custom_divisor;
3316 info->type = new_serial.type;
3317 info->port.close_delay = new_serial.close_delay;
3318 info->port.closing_wait = new_serial.closing_wait;
3319 info->port.low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
3320
3321 check_and_exit:
3322 if (info->port.flags & ASYNC_INITIALIZED) {
3323 change_speed(info);
3324 } else
3325 retval = startup(info);
3326 return retval;
3327 }
3328
3329 /*
3330 * get_lsr_info - get line status register info
3331 *
3332 * Purpose: Let user call ioctl() to get info when the UART physically
3333 * is emptied. On bus types like RS485, the transmitter must
3334 * release the bus after transmitting. This must be done when
3335 * the transmit shift register is empty, not be done when the
3336 * transmit holding register is empty. This functionality
3337 * allows an RS485 driver to be written in user space.
3338 */
3339 static int
3340 get_lsr_info(struct e100_serial * info, unsigned int *value)
3341 {
3342 unsigned int result = TIOCSER_TEMT;
3343 unsigned long curr_time = jiffies;
3344 unsigned long curr_time_usec = GET_JIFFIES_USEC();
3345 unsigned long elapsed_usec =
3346 (curr_time - info->last_tx_active) * 1000000/HZ +
3347 curr_time_usec - info->last_tx_active_usec;
3348
3349 if (info->xmit.head != info->xmit.tail ||
3350 elapsed_usec < 2*info->char_time_usec) {
3351 result = 0;
3352 }
3353
3354 if (copy_to_user(value, &result, sizeof(int)))
3355 return -EFAULT;
3356 return 0;
3357 }
3358
3359 #ifdef SERIAL_DEBUG_IO
3360 struct state_str
3361 {
3362 int state;
3363 const char *str;
3364 };
3365
3366 const struct state_str control_state_str[] = {
3367 {TIOCM_DTR, "DTR" },
3368 {TIOCM_RTS, "RTS"},
3369 {TIOCM_ST, "ST?" },
3370 {TIOCM_SR, "SR?" },
3371 {TIOCM_CTS, "CTS" },
3372 {TIOCM_CD, "CD" },
3373 {TIOCM_RI, "RI" },
3374 {TIOCM_DSR, "DSR" },
3375 {0, NULL }
3376 };
3377
3378 char *get_control_state_str(int MLines, char *s)
3379 {
3380 int i = 0;
3381
3382 s[0]='\0';
3383 while (control_state_str[i].str != NULL) {
3384 if (MLines & control_state_str[i].state) {
3385 if (s[0] != '\0') {
3386 strcat(s, ", ");
3387 }
3388 strcat(s, control_state_str[i].str);
3389 }
3390 i++;
3391 }
3392 return s;
3393 }
3394 #endif
3395
3396 static int
3397 rs_break(struct tty_struct *tty, int break_state)
3398 {
3399 struct e100_serial *info = (struct e100_serial *)tty->driver_data;
3400 unsigned long flags;
3401
3402 if (!info->ioport)
3403 return -EIO;
3404
3405 local_irq_save(flags);
3406 if (break_state == -1) {
3407 /* Go to manual mode and set the txd pin to 0 */
3408 /* Clear bit 7 (txd) and 6 (tr_enable) */
3409 info->tx_ctrl &= 0x3F;
3410 } else {
3411 /* Set bit 7 (txd) and 6 (tr_enable) */
3412 info->tx_ctrl |= (0x80 | 0x40);
3413 }
3414 info->ioport[REG_TR_CTRL] = info->tx_ctrl;
3415 local_irq_restore(flags);
3416 return 0;
3417 }
3418
3419 static int
3420 rs_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear)
3421 {
3422 struct e100_serial *info = (struct e100_serial *)tty->driver_data;
3423 unsigned long flags;
3424
3425 local_irq_save(flags);
3426
3427 if (clear & TIOCM_RTS)
3428 e100_rts(info, 0);
3429 if (clear & TIOCM_DTR)
3430 e100_dtr(info, 0);
3431 /* Handle FEMALE behaviour */
3432 if (clear & TIOCM_RI)
3433 e100_ri_out(info, 0);
3434 if (clear & TIOCM_CD)
3435 e100_cd_out(info, 0);
3436
3437 if (set & TIOCM_RTS)
3438 e100_rts(info, 1);
3439 if (set & TIOCM_DTR)
3440 e100_dtr(info, 1);
3441 /* Handle FEMALE behaviour */
3442 if (set & TIOCM_RI)
3443 e100_ri_out(info, 1);
3444 if (set & TIOCM_CD)
3445 e100_cd_out(info, 1);
3446
3447 local_irq_restore(flags);
3448 return 0;
3449 }
3450
3451 static int
3452 rs_tiocmget(struct tty_struct *tty)
3453 {
3454 struct e100_serial *info = (struct e100_serial *)tty->driver_data;
3455 unsigned int result;
3456 unsigned long flags;
3457
3458 local_irq_save(flags);
3459
3460 result =
3461 (!E100_RTS_GET(info) ? TIOCM_RTS : 0)
3462 | (!E100_DTR_GET(info) ? TIOCM_DTR : 0)
3463 | (!E100_RI_GET(info) ? TIOCM_RNG : 0)
3464 | (!E100_DSR_GET(info) ? TIOCM_DSR : 0)
3465 | (!E100_CD_GET(info) ? TIOCM_CAR : 0)
3466 | (!E100_CTS_GET(info) ? TIOCM_CTS : 0);
3467
3468 local_irq_restore(flags);
3469
3470 #ifdef SERIAL_DEBUG_IO
3471 printk(KERN_DEBUG "ser%i: modem state: %i 0x%08X\n",
3472 info->line, result, result);
3473 {
3474 char s[100];
3475
3476 get_control_state_str(result, s);
3477 printk(KERN_DEBUG "state: %s\n", s);
3478 }
3479 #endif
3480 return result;
3481
3482 }
3483
3484
3485 static int
3486 rs_ioctl(struct tty_struct *tty,
3487 unsigned int cmd, unsigned long arg)
3488 {
3489 struct e100_serial * info = (struct e100_serial *)tty->driver_data;
3490
3491 if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
3492 (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGWILD) &&
3493 (cmd != TIOCSERSWILD) && (cmd != TIOCSERGSTRUCT)) {
3494 if (tty->flags & (1 << TTY_IO_ERROR))
3495 return -EIO;
3496 }
3497
3498 switch (cmd) {
3499 case TIOCGSERIAL:
3500 return get_serial_info(info,
3501 (struct serial_struct *) arg);
3502 case TIOCSSERIAL:
3503 return set_serial_info(info,
3504 (struct serial_struct *) arg);
3505 case TIOCSERGETLSR: /* Get line status register */
3506 return get_lsr_info(info, (unsigned int *) arg);
3507
3508 case TIOCSERGSTRUCT:
3509 if (copy_to_user((struct e100_serial *) arg,
3510 info, sizeof(struct e100_serial)))
3511 return -EFAULT;
3512 return 0;
3513
3514 #if defined(CONFIG_ETRAX_RS485)
3515 case TIOCSERSETRS485:
3516 {
3517 /* In this ioctl we still use the old structure
3518 * rs485_control for backward compatibility
3519 * (if we use serial_rs485, then old user-level code
3520 * wouldn't work anymore...).
3521 * The use of this ioctl is deprecated: use TIOCSRS485
3522 * instead.*/
3523 struct rs485_control rs485ctrl;
3524 struct serial_rs485 rs485data;
3525 printk(KERN_DEBUG "The use of this ioctl is deprecated. Use TIOCSRS485 instead\n");
3526 if (copy_from_user(&rs485ctrl, (struct rs485_control *)arg,
3527 sizeof(rs485ctrl)))
3528 return -EFAULT;
3529
3530 rs485data.delay_rts_before_send = rs485ctrl.delay_rts_before_send;
3531 rs485data.flags = 0;
3532
3533 if (rs485ctrl.enabled)
3534 rs485data.flags |= SER_RS485_ENABLED;
3535 else
3536 rs485data.flags &= ~(SER_RS485_ENABLED);
3537
3538 if (rs485ctrl.rts_on_send)
3539 rs485data.flags |= SER_RS485_RTS_ON_SEND;
3540 else
3541 rs485data.flags &= ~(SER_RS485_RTS_ON_SEND);
3542
3543 if (rs485ctrl.rts_after_sent)
3544 rs485data.flags |= SER_RS485_RTS_AFTER_SEND;
3545 else
3546 rs485data.flags &= ~(SER_RS485_RTS_AFTER_SEND);
3547
3548 return e100_enable_rs485(tty, &rs485data);
3549 }
3550
3551 case TIOCSRS485:
3552 {
3553 /* This is the new version of TIOCSRS485, with new
3554 * data structure serial_rs485 */
3555 struct serial_rs485 rs485data;
3556 if (copy_from_user(&rs485data, (struct rs485_control *)arg,
3557 sizeof(rs485data)))
3558 return -EFAULT;
3559
3560 return e100_enable_rs485(tty, &rs485data);
3561 }
3562
3563 case TIOCGRS485:
3564 {
3565 struct serial_rs485 *rs485data =
3566 &(((struct e100_serial *)tty->driver_data)->rs485);
3567 /* This is the ioctl to get RS485 data from user-space */
3568 if (copy_to_user((struct serial_rs485 *) arg,
3569 rs485data,
3570 sizeof(struct serial_rs485)))
3571 return -EFAULT;
3572 break;
3573 }
3574
3575 case TIOCSERWRRS485:
3576 {
3577 struct rs485_write rs485wr;
3578 if (copy_from_user(&rs485wr, (struct rs485_write *)arg,
3579 sizeof(rs485wr)))
3580 return -EFAULT;
3581
3582 return e100_write_rs485(tty, rs485wr.outc, rs485wr.outc_size);
3583 }
3584 #endif
3585
3586 default:
3587 return -ENOIOCTLCMD;
3588 }
3589 return 0;
3590 }
3591
3592 static void
3593 rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
3594 {
3595 struct e100_serial *info = (struct e100_serial *)tty->driver_data;
3596
3597 change_speed(info);
3598
3599 /* Handle turning off CRTSCTS */
3600 if ((old_termios->c_cflag & CRTSCTS) &&
3601 !(tty->termios.c_cflag & CRTSCTS))
3602 rs_start(tty);
3603
3604 }
3605
3606 /*
3607 * ------------------------------------------------------------
3608 * rs_close()
3609 *
3610 * This routine is called when the serial port gets closed. First, we
3611 * wait for the last remaining data to be sent. Then, we unlink its
3612 * S structure from the interrupt chain if necessary, and we free
3613 * that IRQ if nothing is left in the chain.
3614 * ------------------------------------------------------------
3615 */
3616 static void
3617 rs_close(struct tty_struct *tty, struct file * filp)
3618 {
3619 struct e100_serial * info = (struct e100_serial *)tty->driver_data;
3620 unsigned long flags;
3621
3622 if (!info)
3623 return;
3624
3625 /* interrupts are disabled for this entire function */
3626
3627 local_irq_save(flags);
3628
3629 if (tty_hung_up_p(filp)) {
3630 local_irq_restore(flags);
3631 return;
3632 }
3633
3634 #ifdef SERIAL_DEBUG_OPEN
3635 printk("[%d] rs_close ttyS%d, count = %d\n", current->pid,
3636 info->line, info->count);
3637 #endif
3638 if ((tty->count == 1) && (info->port.count != 1)) {
3639 /*
3640 * Uh, oh. tty->count is 1, which means that the tty
3641 * structure will be freed. Info->count should always
3642 * be one in these conditions. If it's greater than
3643 * one, we've got real problems, since it means the
3644 * serial port won't be shutdown.
3645 */
3646 printk(KERN_ERR
3647 "rs_close: bad serial port count; tty->count is 1, "
3648 "info->count is %d\n", info->port.count);
3649 info->port.count = 1;
3650 }
3651 if (--info->port.count < 0) {
3652 printk(KERN_ERR "rs_close: bad serial port count for ttyS%d: %d\n",
3653 info->line, info->port.count);
3654 info->port.count = 0;
3655 }
3656 if (info->port.count) {
3657 local_irq_restore(flags);
3658 return;
3659 }
3660 info->port.flags |= ASYNC_CLOSING;
3661 /*
3662 * Now we wait for the transmit buffer to clear; and we notify
3663 * the line discipline to only process XON/XOFF characters.
3664 */
3665 tty->closing = 1;
3666 if (info->port.closing_wait != ASYNC_CLOSING_WAIT_NONE)
3667 tty_wait_until_sent(tty, info->port.closing_wait);
3668 /*
3669 * At this point we stop accepting input. To do this, we
3670 * disable the serial receiver and the DMA receive interrupt.
3671 */
3672 #ifdef SERIAL_HANDLE_EARLY_ERRORS
3673 e100_disable_serial_data_irq(info);
3674 #endif
3675
3676 e100_disable_rx(info);
3677 e100_disable_rx_irq(info);
3678
3679 if (info->port.flags & ASYNC_INITIALIZED) {
3680 /*
3681 * Before we drop DTR, make sure the UART transmitter
3682 * has completely drained; this is especially
3683 * important as we have a transmit FIFO!
3684 */
3685 rs_wait_until_sent(tty, HZ);
3686 }
3687
3688 shutdown(info);
3689 rs_flush_buffer(tty);
3690 tty_ldisc_flush(tty);
3691 tty->closing = 0;
3692 info->event = 0;
3693 info->port.tty = NULL;
3694 if (info->port.blocked_open) {
3695 if (info->port.close_delay)
3696 schedule_timeout_interruptible(info->port.close_delay);
3697 wake_up_interruptible(&info->port.open_wait);
3698 }
3699 info->port.flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
3700 wake_up_interruptible(&info->port.close_wait);
3701 local_irq_restore(flags);
3702
3703 /* port closed */
3704
3705 #if defined(CONFIG_ETRAX_RS485)
3706 if (info->rs485.flags & SER_RS485_ENABLED) {
3707 info->rs485.flags &= ~(SER_RS485_ENABLED);
3708 #if defined(CONFIG_ETRAX_RS485_ON_PA)
3709 *R_PORT_PA_DATA = port_pa_data_shadow &= ~(1 << rs485_pa_bit);
3710 #endif
3711 #if defined(CONFIG_ETRAX_RS485_ON_PORT_G)
3712 REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
3713 rs485_port_g_bit, 0);
3714 #endif
3715 #if defined(CONFIG_ETRAX_RS485_LTC1387)
3716 REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
3717 CONFIG_ETRAX_RS485_LTC1387_DXEN_PORT_G_BIT, 0);
3718 REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
3719 CONFIG_ETRAX_RS485_LTC1387_RXEN_PORT_G_BIT, 0);
3720 #endif
3721 }
3722 #endif
3723
3724 /*
3725 * Release any allocated DMA irq's.
3726 */
3727 if (info->dma_in_enabled) {
3728 free_irq(info->dma_in_irq_nbr, info);
3729 cris_free_dma(info->dma_in_nbr, info->dma_in_irq_description);
3730 info->uses_dma_in = 0;
3731 #ifdef SERIAL_DEBUG_OPEN
3732 printk(KERN_DEBUG "DMA irq '%s' freed\n",
3733 info->dma_in_irq_description);
3734 #endif
3735 }
3736 if (info->dma_out_enabled) {
3737 free_irq(info->dma_out_irq_nbr, info);
3738 cris_free_dma(info->dma_out_nbr, info->dma_out_irq_description);
3739 info->uses_dma_out = 0;
3740 #ifdef SERIAL_DEBUG_OPEN
3741 printk(KERN_DEBUG "DMA irq '%s' freed\n",
3742 info->dma_out_irq_description);
3743 #endif
3744 }
3745 }
3746
3747 /*
3748 * rs_wait_until_sent() --- wait until the transmitter is empty
3749 */
3750 static void rs_wait_until_sent(struct tty_struct *tty, int timeout)
3751 {
3752 unsigned long orig_jiffies;
3753 struct e100_serial *info = (struct e100_serial *)tty->driver_data;
3754 unsigned long curr_time = jiffies;
3755 unsigned long curr_time_usec = GET_JIFFIES_USEC();
3756 long elapsed_usec =
3757 (curr_time - info->last_tx_active) * (1000000/HZ) +
3758 curr_time_usec - info->last_tx_active_usec;
3759
3760 /*
3761 * Check R_DMA_CHx_STATUS bit 0-6=number of available bytes in FIFO
3762 * R_DMA_CHx_HWSW bit 31-16=nbr of bytes left in DMA buffer (0=64k)
3763 */
3764 orig_jiffies = jiffies;
3765 while (info->xmit.head != info->xmit.tail || /* More in send queue */
3766 (*info->ostatusadr & 0x007f) || /* more in FIFO */
3767 (elapsed_usec < 2*info->char_time_usec)) {
3768 schedule_timeout_interruptible(1);
3769 if (signal_pending(current))
3770 break;
3771 if (timeout && time_after(jiffies, orig_jiffies + timeout))
3772 break;
3773 curr_time = jiffies;
3774 curr_time_usec = GET_JIFFIES_USEC();
3775 elapsed_usec =
3776 (curr_time - info->last_tx_active) * (1000000/HZ) +
3777 curr_time_usec - info->last_tx_active_usec;
3778 }
3779 set_current_state(TASK_RUNNING);
3780 }
3781
3782 /*
3783 * rs_hangup() --- called by tty_hangup() when a hangup is signaled.
3784 */
3785 void
3786 rs_hangup(struct tty_struct *tty)
3787 {
3788 struct e100_serial * info = (struct e100_serial *)tty->driver_data;
3789
3790 rs_flush_buffer(tty);
3791 shutdown(info);
3792 info->event = 0;
3793 info->port.count = 0;
3794 info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
3795 info->port.tty = NULL;
3796 wake_up_interruptible(&info->port.open_wait);
3797 }
3798
3799 /*
3800 * ------------------------------------------------------------
3801 * rs_open() and friends
3802 * ------------------------------------------------------------
3803 */
3804 static int
3805 block_til_ready(struct tty_struct *tty, struct file * filp,
3806 struct e100_serial *info)
3807 {
3808 DECLARE_WAITQUEUE(wait, current);
3809 unsigned long flags;
3810 int retval;
3811 int do_clocal = 0;
3812
3813 /*
3814 * If the device is in the middle of being closed, then block
3815 * until it's done, and then try again.
3816 */
3817 if (info->port.flags & ASYNC_CLOSING) {
3818 wait_event_interruptible_tty(tty, info->port.close_wait,
3819 !(info->port.flags & ASYNC_CLOSING));
3820 #ifdef SERIAL_DO_RESTART
3821 if (info->port.flags & ASYNC_HUP_NOTIFY)
3822 return -EAGAIN;
3823 else
3824 return -ERESTARTSYS;
3825 #else
3826 return -EAGAIN;
3827 #endif
3828 }
3829
3830 /*
3831 * If non-blocking mode is set, or the port is not enabled,
3832 * then make the check up front and then exit.
3833 */
3834 if ((filp->f_flags & O_NONBLOCK) ||
3835 (tty->flags & (1 << TTY_IO_ERROR))) {
3836 info->port.flags |= ASYNC_NORMAL_ACTIVE;
3837 return 0;
3838 }
3839
3840 if (tty->termios.c_cflag & CLOCAL) {
3841 do_clocal = 1;
3842 }
3843
3844 /*
3845 * Block waiting for the carrier detect and the line to become
3846 * free (i.e., not in use by the callout). While we are in
3847 * this loop, info->port.count is dropped by one, so that
3848 * rs_close() knows when to free things. We restore it upon
3849 * exit, either normal or abnormal.
3850 */
3851 retval = 0;
3852 add_wait_queue(&info->port.open_wait, &wait);
3853 #ifdef SERIAL_DEBUG_OPEN
3854 printk("block_til_ready before block: ttyS%d, count = %d\n",
3855 info->line, info->port.count);
3856 #endif
3857 local_irq_save(flags);
3858 info->port.count--;
3859 local_irq_restore(flags);
3860 info->port.blocked_open++;
3861 while (1) {
3862 local_irq_save(flags);
3863 /* assert RTS and DTR */
3864 e100_rts(info, 1);
3865 e100_dtr(info, 1);
3866 local_irq_restore(flags);
3867 set_current_state(TASK_INTERRUPTIBLE);
3868 if (tty_hung_up_p(filp) ||
3869 !(info->port.flags & ASYNC_INITIALIZED)) {
3870 #ifdef SERIAL_DO_RESTART
3871 if (info->port.flags & ASYNC_HUP_NOTIFY)
3872 retval = -EAGAIN;
3873 else
3874 retval = -ERESTARTSYS;
3875 #else
3876 retval = -EAGAIN;
3877 #endif
3878 break;
3879 }
3880 if (!(info->port.flags & ASYNC_CLOSING) && do_clocal)
3881 /* && (do_clocal || DCD_IS_ASSERTED) */
3882 break;
3883 if (signal_pending(current)) {
3884 retval = -ERESTARTSYS;
3885 break;
3886 }
3887 #ifdef SERIAL_DEBUG_OPEN
3888 printk("block_til_ready blocking: ttyS%d, count = %d\n",
3889 info->line, info->port.count);
3890 #endif
3891 tty_unlock(tty);
3892 schedule();
3893 tty_lock(tty);
3894 }
3895 set_current_state(TASK_RUNNING);
3896 remove_wait_queue(&info->port.open_wait, &wait);
3897 if (!tty_hung_up_p(filp))
3898 info->port.count++;
3899 info->port.blocked_open--;
3900 #ifdef SERIAL_DEBUG_OPEN
3901 printk("block_til_ready after blocking: ttyS%d, count = %d\n",
3902 info->line, info->port.count);
3903 #endif
3904 if (retval)
3905 return retval;
3906 info->port.flags |= ASYNC_NORMAL_ACTIVE;
3907 return 0;
3908 }
3909
3910 static void
3911 deinit_port(struct e100_serial *info)
3912 {
3913 if (info->dma_out_enabled) {
3914 cris_free_dma(info->dma_out_nbr, info->dma_out_irq_description);
3915 free_irq(info->dma_out_irq_nbr, info);
3916 }
3917 if (info->dma_in_enabled) {
3918 cris_free_dma(info->dma_in_nbr, info->dma_in_irq_description);
3919 free_irq(info->dma_in_irq_nbr, info);
3920 }
3921 }
3922
3923 /*
3924 * This routine is called whenever a serial port is opened.
3925 * It performs the serial-specific initialization for the tty structure.
3926 */
3927 static int
3928 rs_open(struct tty_struct *tty, struct file * filp)
3929 {
3930 struct e100_serial *info;
3931 int retval;
3932 int allocated_resources = 0;
3933
3934 info = rs_table + tty->index;
3935 if (!info->enabled)
3936 return -ENODEV;
3937
3938 #ifdef SERIAL_DEBUG_OPEN
3939 printk("[%d] rs_open %s, count = %d\n", current->pid, tty->name,
3940 info->port.count);
3941 #endif
3942
3943 info->port.count++;
3944 tty->driver_data = info;
3945 info->port.tty = tty;
3946
3947 info->port.low_latency = !!(info->port.flags & ASYNC_LOW_LATENCY);
3948
3949 /*
3950 * If the port is in the middle of closing, bail out now
3951 */
3952 if (info->port.flags & ASYNC_CLOSING) {
3953 wait_event_interruptible_tty(tty, info->port.close_wait,
3954 !(info->port.flags & ASYNC_CLOSING));
3955 #ifdef SERIAL_DO_RESTART
3956 return ((info->port.flags & ASYNC_HUP_NOTIFY) ?
3957 -EAGAIN : -ERESTARTSYS);
3958 #else
3959 return -EAGAIN;
3960 #endif
3961 }
3962
3963 /*
3964 * If DMA is enabled try to allocate the irq's.
3965 */
3966 if (info->port.count == 1) {
3967 allocated_resources = 1;
3968 if (info->dma_in_enabled) {
3969 if (request_irq(info->dma_in_irq_nbr,
3970 rec_interrupt,
3971 info->dma_in_irq_flags,
3972 info->dma_in_irq_description,
3973 info)) {
3974 printk(KERN_WARNING "DMA irq '%s' busy; "
3975 "falling back to non-DMA mode\n",
3976 info->dma_in_irq_description);
3977 /* Make sure we never try to use DMA in */
3978 /* for the port again. */
3979 info->dma_in_enabled = 0;
3980 } else if (cris_request_dma(info->dma_in_nbr,
3981 info->dma_in_irq_description,
3982 DMA_VERBOSE_ON_ERROR,
3983 info->dma_owner)) {
3984 free_irq(info->dma_in_irq_nbr, info);
3985 printk(KERN_WARNING "DMA '%s' busy; "
3986 "falling back to non-DMA mode\n",
3987 info->dma_in_irq_description);
3988 /* Make sure we never try to use DMA in */
3989 /* for the port again. */
3990 info->dma_in_enabled = 0;
3991 }
3992 #ifdef SERIAL_DEBUG_OPEN
3993 else
3994 printk(KERN_DEBUG "DMA irq '%s' allocated\n",
3995 info->dma_in_irq_description);
3996 #endif
3997 }
3998 if (info->dma_out_enabled) {
3999 if (request_irq(info->dma_out_irq_nbr,
4000 tr_interrupt,
4001 info->dma_out_irq_flags,
4002 info->dma_out_irq_description,
4003 info)) {
4004 printk(KERN_WARNING "DMA irq '%s' busy; "
4005 "falling back to non-DMA mode\n",
4006 info->dma_out_irq_description);
4007 /* Make sure we never try to use DMA out */
4008 /* for the port again. */
4009 info->dma_out_enabled = 0;
4010 } else if (cris_request_dma(info->dma_out_nbr,
4011 info->dma_out_irq_description,
4012 DMA_VERBOSE_ON_ERROR,
4013 info->dma_owner)) {
4014 free_irq(info->dma_out_irq_nbr, info);
4015 printk(KERN_WARNING "DMA '%s' busy; "
4016 "falling back to non-DMA mode\n",
4017 info->dma_out_irq_description);
4018 /* Make sure we never try to use DMA out */
4019 /* for the port again. */
4020 info->dma_out_enabled = 0;
4021 }
4022 #ifdef SERIAL_DEBUG_OPEN
4023 else
4024 printk(KERN_DEBUG "DMA irq '%s' allocated\n",
4025 info->dma_out_irq_description);
4026 #endif
4027 }
4028 }
4029
4030 /*
4031 * Start up the serial port
4032 */
4033
4034 retval = startup(info);
4035 if (retval) {
4036 if (allocated_resources)
4037 deinit_port(info);
4038
4039 /* FIXME Decrease count info->port.count here too? */
4040 return retval;
4041 }
4042
4043
4044 retval = block_til_ready(tty, filp, info);
4045 if (retval) {
4046 #ifdef SERIAL_DEBUG_OPEN
4047 printk("rs_open returning after block_til_ready with %d\n",
4048 retval);
4049 #endif
4050 if (allocated_resources)
4051 deinit_port(info);
4052
4053 return retval;
4054 }
4055
4056 #ifdef SERIAL_DEBUG_OPEN
4057 printk("rs_open ttyS%d successful...\n", info->line);
4058 #endif
4059 DLOG_INT_TRIG( log_int_pos = 0);
4060
4061 DFLIP( if (info->line == SERIAL_DEBUG_LINE) {
4062 info->icount.rx = 0;
4063 } );
4064
4065 return 0;
4066 }
4067
4068 #ifdef CONFIG_PROC_FS
4069 /*
4070 * /proc fs routines....
4071 */
4072
4073 static void seq_line_info(struct seq_file *m, struct e100_serial *info)
4074 {
4075 unsigned long tmp;
4076
4077 seq_printf(m, "%d: uart:E100 port:%lX irq:%d",
4078 info->line, (unsigned long)info->ioport, info->irq);
4079
4080 if (!info->ioport || (info->type == PORT_UNKNOWN)) {
4081 seq_printf(m, "\n");
4082 return;
4083 }
4084
4085 seq_printf(m, " baud:%d", info->baud);
4086 seq_printf(m, " tx:%lu rx:%lu",
4087 (unsigned long)info->icount.tx,
4088 (unsigned long)info->icount.rx);
4089 tmp = CIRC_CNT(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE);
4090 if (tmp)
4091 seq_printf(m, " tx_pend:%lu/%lu",
4092 (unsigned long)tmp,
4093 (unsigned long)SERIAL_XMIT_SIZE);
4094
4095 seq_printf(m, " rx_pend:%lu/%lu",
4096 (unsigned long)info->recv_cnt,
4097 (unsigned long)info->max_recv_cnt);
4098
4099 #if 1
4100 if (info->port.tty) {
4101 if (info->port.tty->stopped)
4102 seq_printf(m, " stopped:%i",
4103 (int)info->port.tty->stopped);
4104 }
4105
4106 {
4107 unsigned char rstat = info->ioport[REG_STATUS];
4108 if (rstat & IO_MASK(R_SERIAL0_STATUS, xoff_detect))
4109 seq_printf(m, " xoff_detect:1");
4110 }
4111
4112 #endif
4113
4114 if (info->icount.frame)
4115 seq_printf(m, " fe:%lu", (unsigned long)info->icount.frame);
4116
4117 if (info->icount.parity)
4118 seq_printf(m, " pe:%lu", (unsigned long)info->icount.parity);
4119
4120 if (info->icount.brk)
4121 seq_printf(m, " brk:%lu", (unsigned long)info->icount.brk);
4122
4123 if (info->icount.overrun)
4124 seq_printf(m, " oe:%lu", (unsigned long)info->icount.overrun);
4125
4126 /*
4127 * Last thing is the RS-232 status lines
4128 */
4129 if (!E100_RTS_GET(info))
4130 seq_puts(m, "|RTS");
4131 if (!E100_CTS_GET(info))
4132 seq_puts(m, "|CTS");
4133 if (!E100_DTR_GET(info))
4134 seq_puts(m, "|DTR");
4135 if (!E100_DSR_GET(info))
4136 seq_puts(m, "|DSR");
4137 if (!E100_CD_GET(info))
4138 seq_puts(m, "|CD");
4139 if (!E100_RI_GET(info))
4140 seq_puts(m, "|RI");
4141 seq_puts(m, "\n");
4142 }
4143
4144
4145 static int crisv10_proc_show(struct seq_file *m, void *v)
4146 {
4147 int i;
4148
4149 seq_printf(m, "serinfo:1.0 driver:%s\n", serial_version);
4150
4151 for (i = 0; i < NR_PORTS; i++) {
4152 if (!rs_table[i].enabled)
4153 continue;
4154 seq_line_info(m, &rs_table[i]);
4155 }
4156 #ifdef DEBUG_LOG_INCLUDED
4157 for (i = 0; i < debug_log_pos; i++) {
4158 seq_printf(m, "%-4i %lu.%lu ",
4159 i, debug_log[i].time,
4160 timer_data_to_ns(debug_log[i].timer_data));
4161 seq_printf(m, debug_log[i].string, debug_log[i].value);
4162 }
4163 seq_printf(m, "debug_log %i/%i\n", i, DEBUG_LOG_SIZE);
4164 debug_log_pos = 0;
4165 #endif
4166 return 0;
4167 }
4168
4169 static int crisv10_proc_open(struct inode *inode, struct file *file)
4170 {
4171 return single_open(file, crisv10_proc_show, NULL);
4172 }
4173
4174 static const struct file_operations crisv10_proc_fops = {
4175 .owner = THIS_MODULE,
4176 .open = crisv10_proc_open,
4177 .read = seq_read,
4178 .llseek = seq_lseek,
4179 .release = single_release,
4180 };
4181 #endif
4182
4183
4184 /* Finally, routines used to initialize the serial driver. */
4185
4186 static void show_serial_version(void)
4187 {
4188 printk(KERN_INFO
4189 "ETRAX 100LX serial-driver %s, "
4190 "(c) 2000-2004 Axis Communications AB\r\n",
4191 &serial_version[11]); /* "$Revision: x.yy" */
4192 }
4193
4194 /* rs_init inits the driver at boot (using the module_init chain) */
4195
4196 static const struct tty_operations rs_ops = {
4197 .open = rs_open,
4198 .close = rs_close,
4199 .write = rs_write,
4200 .flush_chars = rs_flush_chars,
4201 .write_room = rs_write_room,
4202 .chars_in_buffer = rs_chars_in_buffer,
4203 .flush_buffer = rs_flush_buffer,
4204 .ioctl = rs_ioctl,
4205 .throttle = rs_throttle,
4206 .unthrottle = rs_unthrottle,
4207 .set_termios = rs_set_termios,
4208 .stop = rs_stop,
4209 .start = rs_start,
4210 .hangup = rs_hangup,
4211 .break_ctl = rs_break,
4212 .send_xchar = rs_send_xchar,
4213 .wait_until_sent = rs_wait_until_sent,
4214 .tiocmget = rs_tiocmget,
4215 .tiocmset = rs_tiocmset,
4216 #ifdef CONFIG_PROC_FS
4217 .proc_fops = &crisv10_proc_fops,
4218 #endif
4219 };
4220
4221 static int __init rs_init(void)
4222 {
4223 int i;
4224 struct e100_serial *info;
4225 struct tty_driver *driver = alloc_tty_driver(NR_PORTS);
4226
4227 if (!driver)
4228 return -ENOMEM;
4229
4230 show_serial_version();
4231
4232 /* Setup the timed flush handler system */
4233
4234 #if !defined(CONFIG_ETRAX_SERIAL_FAST_TIMER)
4235 setup_timer(&flush_timer, timed_flush_handler, 0);
4236 mod_timer(&flush_timer, jiffies + 5);
4237 #endif
4238
4239 #if defined(CONFIG_ETRAX_RS485)
4240 #if defined(CONFIG_ETRAX_RS485_ON_PA)
4241 if (cris_io_interface_allocate_pins(if_serial_0, 'a', rs485_pa_bit,
4242 rs485_pa_bit)) {
4243 printk(KERN_ERR "ETRAX100LX serial: Could not allocate "
4244 "RS485 pin\n");
4245 put_tty_driver(driver);
4246 return -EBUSY;
4247 }
4248 #endif
4249 #if defined(CONFIG_ETRAX_RS485_ON_PORT_G)
4250 if (cris_io_interface_allocate_pins(if_serial_0, 'g', rs485_pa_bit,
4251 rs485_port_g_bit)) {
4252 printk(KERN_ERR "ETRAX100LX serial: Could not allocate "
4253 "RS485 pin\n");
4254 put_tty_driver(driver);
4255 return -EBUSY;
4256 }
4257 #endif
4258 #endif
4259
4260 /* Initialize the tty_driver structure */
4261
4262 driver->driver_name = "serial";
4263 driver->name = "ttyS";
4264 driver->major = TTY_MAJOR;
4265 driver->minor_start = 64;
4266 driver->type = TTY_DRIVER_TYPE_SERIAL;
4267 driver->subtype = SERIAL_TYPE_NORMAL;
4268 driver->init_termios = tty_std_termios;
4269 driver->init_termios.c_cflag =
4270 B115200 | CS8 | CREAD | HUPCL | CLOCAL; /* is normally B9600 default... */
4271 driver->init_termios.c_ispeed = 115200;
4272 driver->init_termios.c_ospeed = 115200;
4273 driver->flags = TTY_DRIVER_REAL_RAW;
4274
4275 tty_set_operations(driver, &rs_ops);
4276 serial_driver = driver;
4277
4278 /* do some initializing for the separate ports */
4279 for (i = 0, info = rs_table; i < NR_PORTS; i++,info++) {
4280 if (info->enabled) {
4281 if (cris_request_io_interface(info->io_if,
4282 info->io_if_description)) {
4283 printk(KERN_ERR "ETRAX100LX async serial: "
4284 "Could not allocate IO pins for "
4285 "%s, port %d\n",
4286 info->io_if_description, i);
4287 info->enabled = 0;
4288 }
4289 }
4290 tty_port_init(&info->port);
4291 info->uses_dma_in = 0;
4292 info->uses_dma_out = 0;
4293 info->line = i;
4294 info->port.tty = NULL;
4295 info->type = PORT_ETRAX;
4296 info->tr_running = 0;
4297 info->forced_eop = 0;
4298 info->baud_base = DEF_BAUD_BASE;
4299 info->custom_divisor = 0;
4300 info->x_char = 0;
4301 info->event = 0;
4302 info->xmit.buf = NULL;
4303 info->xmit.tail = info->xmit.head = 0;
4304 info->first_recv_buffer = info->last_recv_buffer = NULL;
4305 info->recv_cnt = info->max_recv_cnt = 0;
4306 info->last_tx_active_usec = 0;
4307 info->last_tx_active = 0;
4308
4309 #if defined(CONFIG_ETRAX_RS485)
4310 /* Set sane defaults */
4311 info->rs485.flags &= ~(SER_RS485_RTS_ON_SEND);
4312 info->rs485.flags |= SER_RS485_RTS_AFTER_SEND;
4313 info->rs485.delay_rts_before_send = 0;
4314 info->rs485.flags &= ~(SER_RS485_ENABLED);
4315 #endif
4316 INIT_WORK(&info->work, do_softint);
4317
4318 if (info->enabled) {
4319 printk(KERN_INFO "%s%d at %p is a builtin UART with DMA\n",
4320 serial_driver->name, info->line, info->ioport);
4321 }
4322 tty_port_link_device(&info->port, driver, i);
4323 }
4324
4325 if (tty_register_driver(driver))
4326 panic("Couldn't register serial driver\n");
4327
4328 #ifdef CONFIG_ETRAX_FAST_TIMER
4329 #ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER
4330 memset(fast_timers, 0, sizeof(fast_timers));
4331 #endif
4332 #ifdef CONFIG_ETRAX_RS485
4333 memset(fast_timers_rs485, 0, sizeof(fast_timers_rs485));
4334 #endif
4335 fast_timer_init();
4336 #endif
4337
4338 #ifndef CONFIG_ETRAX_KGDB
4339 /* Not needed in simulator. May only complicate stuff. */
4340 /* hook the irq's for DMA channel 6 and 7, serial output and input, and some more... */
4341
4342 if (request_irq(SERIAL_IRQ_NBR, ser_interrupt,
4343 IRQF_SHARED, "serial ", driver))
4344 panic("%s: Failed to request irq8", __func__);
4345
4346 #endif
4347
4348 return 0;
4349 }
4350
4351 /* this makes sure that rs_init is called during kernel boot */
4352
4353 module_init(rs_init);
Linux kernel - Deliverables
This page took 0.112136 seconds and 4 git commands to generate.