drivers/usb/gadget/Kconfig

   1 #
   2 # USB Gadget support on a system involves
   3 #    (a) a peripheral controller, and
   4 #    (b) the gadget driver using it.
   5 #
   6 # NOTE:  Gadget support ** DOES NOT ** depend on host-side CONFIG_USB !!
   7 #
   8 #  - Host systems (like PCs) need CONFIG_USB (with "A" jacks).
   9 #  - Peripherals (like PDAs) need CONFIG_USB_GADGET (with "B" jacks).
  10 #  - Some systems have both kinds of controllers.
  11 #
  12 # With help from a special transceiver and a "Mini-AB" jack, systems with
  13 # both kinds of controller can also support "USB On-the-Go" (CONFIG_USB_OTG).
  14 #
  15
  16 menuconfig USB_GADGET
  17         tristate "USB Gadget Support"
  18         help
  19            USB is a master/slave protocol, organized with one master
  20            host (such as a PC) controlling up to 127 peripheral devices.
  21            The USB hardware is asymmetric, which makes it easier to set up:
  22            you can't connect a "to-the-host" connector to a peripheral.
  23
  24            Linux can run in the host, or in the peripheral.  In both cases
  25            you need a low level bus controller driver, and some software
  26            talking to it.  Peripheral controllers are often discrete silicon,
  27            or are integrated with the CPU in a microcontroller.  The more
  28            familiar host side controllers have names like "EHCI", "OHCI",
  29            or "UHCI", and are usually integrated into southbridges on PC
  30            motherboards.
  31
  32            Enable this configuration option if you want to run Linux inside
  33            a USB peripheral device.  Configure one hardware driver for your
  34            peripheral/device side bus controller, and a "gadget driver" for
  35            your peripheral protocol.  (If you use modular gadget drivers,
  36            you may configure more than one.)
  37
  38            If in doubt, say "N" and don't enable these drivers; most people
  39            don't have this kind of hardware (except maybe inside Linux PDAs).
  40
  41            For more information, see <http://www.linux-usb.org/gadget> and
  42            the kernel DocBook documentation for this API.
  43
  44 if USB_GADGET
  45
  46 config USB_GADGET_DEBUG
  47         boolean "Debugging messages (DEVELOPMENT)"
  48         depends on DEBUG_KERNEL
  49         help
  50            Many controller and gadget drivers will print some debugging
  51            messages if you use this option to ask for those messages.
  52
  53            Avoid enabling these messages, even if you're actively
  54            debugging such a driver.  Many drivers will emit so many
  55            messages that the driver timings are affected, which will
  56            either create new failure modes or remove the one you're
  57            trying to track down.  Never enable these messages for a
  58            production build.
  59
  60 config USB_GADGET_DEBUG_FILES
  61         boolean "Debugging information files (DEVELOPMENT)"
  62         depends on PROC_FS
  63         help
  64            Some of the drivers in the "gadget" framework can expose
  65            debugging information in files such as /proc/driver/udc
  66            (for a peripheral controller).  The information in these
  67            files may help when you're troubleshooting or bringing up a
  68            driver on a new board.   Enable these files by choosing "Y"
  69            here.  If in doubt, or to conserve kernel memory, say "N".
  70
  71 config USB_GADGET_DEBUG_FS
  72         boolean "Debugging information files in debugfs (DEVELOPMENT)"
  73         depends on DEBUG_FS
  74         help
  75            Some of the drivers in the "gadget" framework can expose
  76            debugging information in files under /sys/kernel/debug/.
  77            The information in these files may help when you're
  78            troubleshooting or bringing up a driver on a new board.
  79            Enable these files by choosing "Y" here.  If in doubt, or
  80            to conserve kernel memory, say "N".
  81
  82 config USB_GADGET_VBUS_DRAW
  83         int "Maximum VBUS Power usage (2-500 mA)"
  84         range 2 500
  85         default 2
  86         help
  87            Some devices need to draw power from USB when they are
  88            configured, perhaps to operate circuitry or to recharge
  89            batteries.  This is in addition to any local power supply,
  90            such as an AC adapter or batteries.
  91
  92            Enter the maximum power your device draws through USB, in
  93            milliAmperes.  The permitted range of values is 2 - 500 mA;
  94            0 mA would be legal, but can make some hosts misbehave.
  95
  96            This value will be used except for system-specific gadget
  97            drivers that have more specific information.
  98
  99 config  USB_GADGET_SELECTED
 100         boolean
 101
 102 #
 103 # USB Peripheral Controller Support
 104 #
 105 # The order here is alphabetical, except that integrated controllers go
 106 # before discrete ones so they will be the initial/default value:
 107 #   - integrated/SOC controllers first
 108 #   - licensed IP used in both SOC and discrete versions
 109 #   - discrete ones (including all PCI-only controllers)
 110 #   - debug/dummy gadget+hcd is last.
 111 #
 112 choice
 113         prompt "USB Peripheral Controller"
 114         depends on USB_GADGET
 115         help
 116            A USB device uses a controller to talk to its host.
 117            Systems should have only one such upstream link.
 118            Many controller drivers are platform-specific; these
 119            often need board-specific hooks.
 120
 121 #
 122 # Integrated controllers
 123 #
 124
 125 config USB_GADGET_AT91
 126         boolean "Atmel AT91 USB Device Port"
 127         depends on ARCH_AT91 && !ARCH_AT91SAM9RL && !ARCH_AT91CAP9 && !ARCH_AT91SAM9G45
 128         select USB_GADGET_SELECTED
 129         help
 130            Many Atmel AT91 processors (such as the AT91RM2000) have a
 131            full speed USB Device Port with support for five configurable
 132            endpoints (plus endpoint zero).
 133
 134            Say "y" to link the driver statically, or "m" to build a
 135            dynamically linked module called "at91_udc" and force all
 136            gadget drivers to also be dynamically linked.
 137
 138 config USB_AT91
 139         tristate
 140         depends on USB_GADGET_AT91
 141         default USB_GADGET
 142
 143 config USB_GADGET_ATMEL_USBA
 144         boolean "Atmel USBA"
 145         select USB_GADGET_DUALSPEED
 146         depends on AVR32 || ARCH_AT91CAP9 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G45
 147         help
 148           USBA is the integrated high-speed USB Device controller on
 149           the AT32AP700x, some AT91SAM9 and AT91CAP9 processors from Atmel.
 150
 151 config USB_ATMEL_USBA
 152         tristate
 153         depends on USB_GADGET_ATMEL_USBA
 154         default USB_GADGET
 155         select USB_GADGET_SELECTED
 156
 157 config USB_GADGET_FSL_USB2
 158         boolean "Freescale Highspeed USB DR Peripheral Controller"
 159         depends on FSL_SOC || ARCH_MXC
 160         select USB_GADGET_DUALSPEED
 161         select USB_FSL_MPH_DR_OF
 162         help
 163            Some of Freescale PowerPC processors have a High Speed
 164            Dual-Role(DR) USB controller, which supports device mode.
 165
 166            The number of programmable endpoints is different through
 167            SOC revisions.
 168
 169            Say "y" to link the driver statically, or "m" to build a
 170            dynamically linked module called "fsl_usb2_udc" and force
 171            all gadget drivers to also be dynamically linked.
 172
 173 config USB_FSL_USB2
 174         tristate
 175         depends on USB_GADGET_FSL_USB2
 176         default USB_GADGET
 177         select USB_GADGET_SELECTED
 178
 179 config USB_GADGET_LH7A40X
 180         boolean "LH7A40X"
 181         depends on ARCH_LH7A40X
 182         help
 183            This driver provides USB Device Controller driver for LH7A40x
 184
 185 config USB_LH7A40X
 186         tristate
 187         depends on USB_GADGET_LH7A40X
 188         default USB_GADGET
 189         select USB_GADGET_SELECTED
 190
 191 config USB_GADGET_OMAP
 192         boolean "OMAP USB Device Controller"
 193         depends on ARCH_OMAP
 194         select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_OMAP_H4_OTG
 195         select USB_OTG_UTILS if ARCH_OMAP
 196         help
 197            Many Texas Instruments OMAP processors have flexible full
 198            speed USB device controllers, with support for up to 30
 199            endpoints (plus endpoint zero).  This driver supports the
 200            controller in the OMAP 1611, and should work with controllers
 201            in other OMAP processors too, given minor tweaks.
 202
 203            Say "y" to link the driver statically, or "m" to build a
 204            dynamically linked module called "omap_udc" and force all
 205            gadget drivers to also be dynamically linked.
 206
 207 config USB_OMAP
 208         tristate
 209         depends on USB_GADGET_OMAP
 210         default USB_GADGET
 211         select USB_GADGET_SELECTED
 212
 213 config USB_GADGET_PXA25X
 214         boolean "PXA 25x or IXP 4xx"
 215         depends on (ARCH_PXA && PXA25x) || ARCH_IXP4XX
 216         select USB_OTG_UTILS
 217         help
 218            Intel's PXA 25x series XScale ARM-5TE processors include
 219            an integrated full speed USB 1.1 device controller.  The
 220            controller in the IXP 4xx series is register-compatible.
 221
 222            It has fifteen fixed-function endpoints, as well as endpoint
 223            zero (for control transfers).
 224
 225            Say "y" to link the driver statically, or "m" to build a
 226            dynamically linked module called "pxa25x_udc" and force all
 227            gadget drivers to also be dynamically linked.
 228
 229 config USB_PXA25X
 230         tristate
 231         depends on USB_GADGET_PXA25X
 232         default USB_GADGET
 233         select USB_GADGET_SELECTED
 234
 235 # if there's only one gadget driver, using only two bulk endpoints,
 236 # don't waste memory for the other endpoints
 237 config USB_PXA25X_SMALL
 238         depends on USB_GADGET_PXA25X
 239         bool
 240         default n if USB_ETH_RNDIS
 241         default y if USB_ZERO
 242         default y if USB_ETH
 243         default y if USB_G_SERIAL
 244
 245 config USB_GADGET_R8A66597
 246         boolean "Renesas R8A66597 USB Peripheral Controller"
 247         select USB_GADGET_DUALSPEED
 248         help
 249            R8A66597 is a discrete USB host and peripheral controller chip that
 250            supports both full and high speed USB 2.0 data transfers.
 251            It has nine configurable endpoints, and endpoint zero.
 252
 253            Say "y" to link the driver statically, or "m" to build a
 254            dynamically linked module called "r8a66597_udc" and force all
 255            gadget drivers to also be dynamically linked.
 256
 257 config USB_R8A66597
 258         tristate
 259         depends on USB_GADGET_R8A66597
 260         default USB_GADGET
 261         select USB_GADGET_SELECTED
 262
 263 config USB_GADGET_PXA27X
 264         boolean "PXA 27x"
 265         depends on ARCH_PXA && (PXA27x || PXA3xx)
 266         select USB_OTG_UTILS
 267         help
 268            Intel's PXA 27x series XScale ARM v5TE processors include
 269            an integrated full speed USB 1.1 device controller.
 270
 271            It has up to 23 endpoints, as well as endpoint zero (for
 272            control transfers).
 273
 274            Say "y" to link the driver statically, or "m" to build a
 275            dynamically linked module called "pxa27x_udc" and force all
 276            gadget drivers to also be dynamically linked.
 277
 278 config USB_PXA27X
 279         tristate
 280         depends on USB_GADGET_PXA27X
 281         default USB_GADGET
 282         select USB_GADGET_SELECTED
 283
 284 config USB_GADGET_S3C_HSOTG
 285         boolean "S3C HS/OtG USB Device controller"
 286         depends on S3C_DEV_USB_HSOTG
 287         select USB_GADGET_S3C_HSOTG_PIO
 288         select USB_GADGET_DUALSPEED
 289         help
 290           The Samsung S3C64XX USB2.0 high-speed gadget controller
 291           integrated into the S3C64XX series SoC.
 292
 293 config USB_S3C_HSOTG
 294         tristate
 295         depends on USB_GADGET_S3C_HSOTG
 296         default USB_GADGET
 297         select USB_GADGET_SELECTED
 298
 299 config USB_GADGET_IMX
 300         boolean "Freescale IMX USB Peripheral Controller"
 301         depends on ARCH_MX1
 302         help
 303            Freescale's IMX series include an integrated full speed
 304            USB 1.1 device controller.  The controller in the IMX series
 305            is register-compatible.
 306
 307            It has Six fixed-function endpoints, as well as endpoint
 308            zero (for control transfers).
 309
 310            Say "y" to link the driver statically, or "m" to build a
 311            dynamically linked module called "imx_udc" and force all
 312            gadget drivers to also be dynamically linked.
 313
 314 config USB_IMX
 315         tristate
 316         depends on USB_GADGET_IMX
 317         default USB_GADGET
 318         select USB_GADGET_SELECTED
 319
 320 config USB_GADGET_S3C2410
 321         boolean "S3C2410 USB Device Controller"
 322         depends on ARCH_S3C2410
 323         help
 324           Samsung's S3C2410 is an ARM-4 processor with an integrated
 325           full speed USB 1.1 device controller.  It has 4 configurable
 326           endpoints, as well as endpoint zero (for control transfers).
 327
 328           This driver has been tested on the S3C2410, S3C2412, and
 329           S3C2440 processors.
 330
 331 config USB_S3C2410
 332         tristate
 333         depends on USB_GADGET_S3C2410
 334         default USB_GADGET
 335         select USB_GADGET_SELECTED
 336
 337 config USB_S3C2410_DEBUG
 338         boolean "S3C2410 udc debug messages"
 339         depends on USB_GADGET_S3C2410
 340
 341 config USB_GADGET_PXA_U2O
 342         boolean "PXA9xx Processor USB2.0 controller"
 343         select USB_GADGET_DUALSPEED
 344         help
 345           PXA9xx Processor series include a high speed USB2.0 device
 346           controller, which support high speed and full speed USB peripheral.
 347
 348 config USB_PXA_U2O
 349         tristate
 350         depends on USB_GADGET_PXA_U2O
 351         default USB_GADGET
 352         select USB_GADGET_SELECTED
 353
 354 #
 355 # Controllers available in both integrated and discrete versions
 356 #
 357
 358 # musb builds in ../musb along with host support
 359 config USB_GADGET_MUSB_HDRC
 360         boolean "Inventra HDRC USB Peripheral (TI, ADI, ...)"
 361         depends on USB_MUSB_HDRC && (USB_MUSB_PERIPHERAL || USB_MUSB_OTG)
 362         select USB_GADGET_DUALSPEED
 363         select USB_GADGET_SELECTED
 364         help
 365           This OTG-capable silicon IP is used in dual designs including
 366           the TI DaVinci, OMAP 243x, OMAP 343x, TUSB 6010, and ADI Blackfin
 367
 368 config USB_GADGET_M66592
 369         boolean "Renesas M66592 USB Peripheral Controller"
 370         select USB_GADGET_DUALSPEED
 371         help
 372            M66592 is a discrete USB peripheral controller chip that
 373            supports both full and high speed USB 2.0 data transfers.
 374            It has seven configurable endpoints, and endpoint zero.
 375
 376            Say "y" to link the driver statically, or "m" to build a
 377            dynamically linked module called "m66592_udc" and force all
 378            gadget drivers to also be dynamically linked.
 379
 380 config USB_M66592
 381         tristate
 382         depends on USB_GADGET_M66592
 383         default USB_GADGET
 384         select USB_GADGET_SELECTED
 385
 386 #
 387 # Controllers available only in discrete form (and all PCI controllers)
 388 #
 389
 390 config USB_GADGET_AMD5536UDC
 391         boolean "AMD5536 UDC"
 392         depends on PCI
 393         select USB_GADGET_DUALSPEED
 394         help
 395            The AMD5536 UDC is part of the AMD Geode CS5536, an x86 southbridge.
 396            It is a USB Highspeed DMA capable USB device controller. Beside ep0
 397            it provides 4 IN and 4 OUT endpoints (bulk or interrupt type).
 398            The UDC port supports OTG operation, and may be used as a host port
 399            if it's not being used to implement peripheral or OTG roles.
 400
 401            Say "y" to link the driver statically, or "m" to build a
 402            dynamically linked module called "amd5536udc" and force all
 403            gadget drivers to also be dynamically linked.
 404
 405 config USB_AMD5536UDC
 406         tristate
 407         depends on USB_GADGET_AMD5536UDC
 408         default USB_GADGET
 409         select USB_GADGET_SELECTED
 410
 411 config USB_GADGET_FSL_QE
 412         boolean "Freescale QE/CPM USB Device Controller"
 413         depends on FSL_SOC && (QUICC_ENGINE || CPM)
 414         help
 415            Some of Freescale PowerPC processors have a Full Speed
 416            QE/CPM2 USB controller, which support device mode with 4
 417            programmable endpoints. This driver supports the
 418            controller in the MPC8360 and MPC8272, and should work with
 419            controllers having QE or CPM2, given minor tweaks.
 420
 421            Set CONFIG_USB_GADGET to "m" to build this driver as a
 422            dynamically linked module called "fsl_qe_udc".
 423
 424 config USB_FSL_QE
 425         tristate
 426         depends on USB_GADGET_FSL_QE
 427         default USB_GADGET
 428         select USB_GADGET_SELECTED
 429
 430 config USB_GADGET_CI13XXX_PCI
 431         boolean "MIPS USB CI13xxx PCI UDC"
 432         depends on PCI
 433         select USB_GADGET_DUALSPEED
 434         help
 435           MIPS USB IP core family device controller
 436           Currently it only supports IP part number CI13412
 437
 438           Say "y" to link the driver statically, or "m" to build a
 439           dynamically linked module called "ci13xxx_udc" and force all
 440           gadget drivers to also be dynamically linked.
 441
 442 config USB_CI13XXX_PCI
 443         tristate
 444         depends on USB_GADGET_CI13XXX_PCI
 445         default USB_GADGET
 446         select USB_GADGET_SELECTED
 447
 448 config USB_GADGET_NET2280
 449         boolean "NetChip 228x"
 450         depends on PCI
 451         select USB_GADGET_DUALSPEED
 452         help
 453            NetChip 2280 / 2282 is a PCI based USB peripheral controller which
 454            supports both full and high speed USB 2.0 data transfers.
 455
 456            It has six configurable endpoints, as well as endpoint zero
 457            (for control transfers) and several endpoints with dedicated
 458            functions.
 459
 460            Say "y" to link the driver statically, or "m" to build a
 461            dynamically linked module called "net2280" and force all
 462            gadget drivers to also be dynamically linked.
 463
 464 config USB_NET2280
 465         tristate
 466         depends on USB_GADGET_NET2280
 467         default USB_GADGET
 468         select USB_GADGET_SELECTED
 469
 470 config USB_GADGET_GOKU
 471         boolean "Toshiba TC86C001 'Goku-S'"
 472         depends on PCI
 473         help
 474            The Toshiba TC86C001 is a PCI device which includes controllers
 475            for full speed USB devices, IDE, I2C, SIO, plus a USB host (OHCI).
 476
 477            The device controller has three configurable (bulk or interrupt)
 478            endpoints, plus endpoint zero (for control transfers).
 479
 480            Say "y" to link the driver statically, or "m" to build a
 481            dynamically linked module called "goku_udc" and to force all
 482            gadget drivers to also be dynamically linked.
 483
 484 config USB_GOKU
 485         tristate
 486         depends on USB_GADGET_GOKU
 487         default USB_GADGET
 488         select USB_GADGET_SELECTED
 489
 490 config USB_GADGET_LANGWELL
 491         boolean "Intel Langwell USB Device Controller"
 492         depends on PCI
 493         select USB_GADGET_DUALSPEED
 494         help
 495            Intel Langwell USB Device Controller is a High-Speed USB
 496            On-The-Go device controller.
 497
 498            The number of programmable endpoints is different through
 499            controller revision.
 500
 501            Say "y" to link the driver statically, or "m" to build a
 502            dynamically linked module called "langwell_udc" and force all
 503            gadget drivers to also be dynamically linked.
 504
 505 config USB_LANGWELL
 506         tristate
 507         depends on USB_GADGET_LANGWELL
 508         default USB_GADGET
 509         select USB_GADGET_SELECTED
 510
 511 config USB_GADGET_EG20T
 512         boolean "Intel EG20T(Topcliff) USB Device controller"
 513         depends on PCI
 514         select USB_GADGET_DUALSPEED
 515         help
 516           This is a USB device driver for EG20T PCH.
 517           EG20T PCH is the platform controller hub that is used in Intel's
 518           general embedded platform. EG20T PCH has USB device interface.
 519           Using this interface, it is able to access system devices connected
 520           to USB device.
 521           This driver enables USB device function.
 522           USB device is a USB peripheral controller which
 523           supports both full and high speed USB 2.0 data transfers.
 524           This driver supports both control transfer and bulk transfer modes.
 525           This driver dose not support interrupt transfer or isochronous
 526           transfer modes.
 527
 528 config USB_EG20T
 529         tristate
 530         depends on USB_GADGET_EG20T
 531         default USB_GADGET
 532         select USB_GADGET_SELECTED
 533
 534 config USB_GADGET_CI13XXX_MSM
 535         boolean "MIPS USB CI13xxx for MSM"
 536         depends on ARCH_MSM
 537         select USB_GADGET_DUALSPEED
 538         select USB_MSM_OTG_72K
 539         help
 540           MSM SoC has chipidea USB controller.  This driver uses
 541           ci13xxx_udc core.
 542           This driver depends on OTG driver for PHY initialization,
 543           clock management, powering up VBUS, and power management.
 544
 545           Say "y" to link the driver statically, or "m" to build a
 546           dynamically linked module called "ci13xxx_msm" and force all
 547           gadget drivers to also be dynamically linked.
 548
 549 config USB_CI13XXX_MSM
 550         tristate
 551         depends on USB_GADGET_CI13XXX_MSM
 552         default USB_GADGET
 553         select USB_GADGET_SELECTED
 554
 555 #
 556 # LAST -- dummy/emulated controller
 557 #
 558
 559 config USB_GADGET_DUMMY_HCD
 560         boolean "Dummy HCD (DEVELOPMENT)"
 561         depends on USB=y || (USB=m && USB_GADGET=m)
 562         select USB_GADGET_DUALSPEED
 563         help
 564           This host controller driver emulates USB, looping all data transfer
 565           requests back to a USB "gadget driver" in the same host.  The host
 566           side is the master; the gadget side is the slave.  Gadget drivers
 567           can be high, full, or low speed; and they have access to endpoints
 568           like those from NET2280, PXA2xx, or SA1100 hardware.
 569
 570           This may help in some stages of creating a driver to embed in a
 571           Linux device, since it lets you debug several parts of the gadget
 572           driver without its hardware or drivers being involved.
 573
 574           Since such a gadget side driver needs to interoperate with a host
 575           side Linux-USB device driver, this may help to debug both sides
 576           of a USB protocol stack.
 577
 578           Say "y" to link the driver statically, or "m" to build a
 579           dynamically linked module called "dummy_hcd" and force all
 580           gadget drivers to also be dynamically linked.
 581
 582 config USB_DUMMY_HCD
 583         tristate
 584         depends on USB_GADGET_DUMMY_HCD
 585         default USB_GADGET
 586         select USB_GADGET_SELECTED
 587
 588 # NOTE:  Please keep dummy_hcd LAST so that "real hardware" appears
 589 # first and will be selected by default.
 590
 591 endchoice
 592
 593 config USB_GADGET_DUALSPEED
 594         bool
 595         depends on USB_GADGET
 596         default n
 597         help
 598           Means that gadget drivers should include extra descriptors
 599           and code to handle dual-speed controllers.
 600
 601 #
 602 # USB Gadget Drivers
 603 #
 604 choice
 605         tristate "USB Gadget Drivers"
 606         depends on USB_GADGET && USB_GADGET_SELECTED
 607         default USB_ETH
 608         help
 609           A Linux "Gadget Driver" talks to the USB Peripheral Controller
 610           driver through the abstract "gadget" API.  Some other operating
 611           systems call these "client" drivers, of which "class drivers"
 612           are a subset (implementing a USB device class specification).
 613           A gadget driver implements one or more USB functions using
 614           the peripheral hardware.
 615
 616           Gadget drivers are hardware-neutral, or "platform independent",
 617           except that they sometimes must understand quirks or limitations
 618           of the particular controllers they work with.  For example, when
 619           a controller doesn't support alternate configurations or provide
 620           enough of the right types of endpoints, the gadget driver might
 621           not be able work with that controller, or might need to implement
 622           a less common variant of a device class protocol.
 623
 624 # this first set of drivers all depend on bulk-capable hardware.
 625
 626 config USB_ZERO
 627         tristate "Gadget Zero (DEVELOPMENT)"
 628         help
 629           Gadget Zero is a two-configuration device.  It either sinks and
 630           sources bulk data; or it loops back a configurable number of
 631           transfers.  It also implements control requests, for "chapter 9"
 632           conformance.  The driver needs only two bulk-capable endpoints, so
 633           it can work on top of most device-side usb controllers.  It's
 634           useful for testing, and is also a working example showing how
 635           USB "gadget drivers" can be written.
 636
 637           Make this be the first driver you try using on top of any new
 638           USB peripheral controller driver.  Then you can use host-side
 639           test software, like the "usbtest" driver, to put your hardware
 640           and its driver through a basic set of functional tests.
 641
 642           Gadget Zero also works with the host-side "usb-skeleton" driver,
 643           and with many kinds of host-side test software.  You may need
 644           to tweak product and vendor IDs before host software knows about
 645           this device, and arrange to select an appropriate configuration.
 646
 647           Say "y" to link the driver statically, or "m" to build a
 648           dynamically linked module called "g_zero".
 649
 650 config USB_ZERO_HNPTEST
 651         boolean "HNP Test Device"
 652         depends on USB_ZERO && USB_OTG
 653         help
 654           You can configure this device to enumerate using the device
 655           identifiers of the USB-OTG test device.  That means that when
 656           this gadget connects to another OTG device, with this one using
 657           the "B-Peripheral" role, that device will use HNP to let this
 658           one serve as the USB host instead (in the "B-Host" role).
 659
 660 config USB_AUDIO
 661         tristate "Audio Gadget (EXPERIMENTAL)"
 662         depends on SND
 663         select SND_PCM
 664         help
 665           Gadget Audio is compatible with USB Audio Class specification 1.0.
 666           It will include at least one AudioControl interface, zero or more
 667           AudioStream interface and zero or more MIDIStream interface.
 668
 669           Gadget Audio will use on-board ALSA (CONFIG_SND) audio card to
 670           playback or capture audio stream.
 671
 672           Say "y" to link the driver statically, or "m" to build a
 673           dynamically linked module called "g_audio".
 674
 675 config USB_ETH
 676         tristate "Ethernet Gadget (with CDC Ethernet support)"
 677         depends on NET
 678         select CRC32
 679         help
 680           This driver implements Ethernet style communication, in one of
 681           several ways:
 682
 683            - The "Communication Device Class" (CDC) Ethernet Control Model.
 684              That protocol is often avoided with pure Ethernet adapters, in
 685              favor of simpler vendor-specific hardware, but is widely
 686              supported by firmware for smart network devices.
 687
 688            - On hardware can't implement that protocol, a simple CDC subset
 689              is used, placing fewer demands on USB.
 690
 691            - CDC Ethernet Emulation Model (EEM) is a newer standard that has
 692              a simpler interface that can be used by more USB hardware.
 693
 694           RNDIS support is an additional option, more demanding than than
 695           subset.
 696
 697           Within the USB device, this gadget driver exposes a network device
 698           "usbX", where X depends on what other networking devices you have.
 699           Treat it like a two-node Ethernet link:  host, and gadget.
 700
 701           The Linux-USB host-side "usbnet" driver interoperates with this
 702           driver, so that deep I/O queues can be supported.  On 2.4 kernels,
 703           use "CDCEther" instead, if you're using the CDC option. That CDC
 704           mode should also interoperate with standard CDC Ethernet class
 705           drivers on other host operating systems.
 706
 707           Say "y" to link the driver statically, or "m" to build a
 708           dynamically linked module called "g_ether".
 709
 710 config USB_ETH_RNDIS
 711         bool "RNDIS support"
 712         depends on USB_ETH
 713         default y
 714         help
 715            Microsoft Windows XP bundles the "Remote NDIS" (RNDIS) protocol,
 716            and Microsoft provides redistributable binary RNDIS drivers for
 717            older versions of Windows.
 718
 719            If you say "y" here, the Ethernet gadget driver will try to provide
 720            a second device configuration, supporting RNDIS to talk to such
 721            Microsoft USB hosts.
 722
 723            To make MS-Windows work with this, use Documentation/usb/linux.inf
 724            as the "driver info file".  For versions of MS-Windows older than
 725            XP, you'll need to download drivers from Microsoft's website; a URL
 726            is given in comments found in that info file.
 727
 728 config USB_ETH_EEM
 729        bool "Ethernet Emulation Model (EEM) support"
 730        depends on USB_ETH
 731        default n
 732        help
 733          CDC EEM is a newer USB standard that is somewhat simpler than CDC ECM
 734          and therefore can be supported by more hardware.  Technically ECM and
 735          EEM are designed for different applications.  The ECM model extends
 736          the network interface to the target (e.g. a USB cable modem), and the
 737          EEM model is for mobile devices to communicate with hosts using
 738          ethernet over USB.  For Linux gadgets, however, the interface with
 739          the host is the same (a usbX device), so the differences are minimal.
 740
 741          If you say "y" here, the Ethernet gadget driver will use the EEM
 742          protocol rather than ECM.  If unsure, say "n".
 743
 744 config USB_GADGETFS
 745         tristate "Gadget Filesystem (EXPERIMENTAL)"
 746         depends on EXPERIMENTAL
 747         help
 748           This driver provides a filesystem based API that lets user mode
 749           programs implement a single-configuration USB device, including
 750           endpoint I/O and control requests that don't relate to enumeration.
 751           All endpoints, transfer speeds, and transfer types supported by
 752           the hardware are available, through read() and write() calls.
 753
 754           Currently, this option is still labelled as EXPERIMENTAL because
 755           of existing race conditions in the underlying in-kernel AIO core.
 756
 757           Say "y" to link the driver statically, or "m" to build a
 758           dynamically linked module called "gadgetfs".
 759
 760 config USB_FUNCTIONFS
 761         tristate "Function Filesystem (EXPERIMENTAL)"
 762         depends on EXPERIMENTAL
 763         select USB_FUNCTIONFS_GENERIC if !(USB_FUNCTIONFS_ETH || USB_FUNCTIONFS_RNDIS)
 764         help
 765           The Function Filesystem (FunctionFS) lets one create USB
 766           composite functions in user space in the same way GadgetFS
 767           lets one create USB gadgets in user space.  This allows creation
 768           of composite gadgets such that some of the functions are
 769           implemented in kernel space (for instance Ethernet, serial or
 770           mass storage) and other are implemented in user space.
 771
 772           If you say "y" or "m" here you will be able what kind of
 773           configurations the gadget will provide.
 774
 775           Say "y" to link the driver statically, or "m" to build
 776           a dynamically linked module called "g_ffs".
 777
 778 config USB_FUNCTIONFS_ETH
 779         bool "Include configuration with CDC ECM (Ethernet)"
 780         depends on USB_FUNCTIONFS && NET
 781         help
 782           Include a configuration with CDC ECM function (Ethernet) and the
 783           Function Filesystem.
 784
 785 config USB_FUNCTIONFS_RNDIS
 786         bool "Include configuration with RNDIS (Ethernet)"
 787         depends on USB_FUNCTIONFS && NET
 788         help
 789           Include a configuration with RNDIS function (Ethernet) and the Filesystem.
 790
 791 config USB_FUNCTIONFS_GENERIC
 792         bool "Include 'pure' configuration"
 793         depends on USB_FUNCTIONFS
 794         help
 795           Include a configuration with the Function Filesystem alone with
 796           no Ethernet interface.
 797
 798 config USB_FILE_STORAGE
 799         tristate "File-backed Storage Gadget"
 800         depends on BLOCK
 801         help
 802           The File-backed Storage Gadget acts as a USB Mass Storage
 803           disk drive.  As its storage repository it can use a regular
 804           file or a block device (in much the same way as the "loop"
 805           device driver), specified as a module parameter.
 806
 807           Say "y" to link the driver statically, or "m" to build a
 808           dynamically linked module called "g_file_storage".
 809
 810 config USB_FILE_STORAGE_TEST
 811         bool "File-backed Storage Gadget testing version"
 812         depends on USB_FILE_STORAGE
 813         default n
 814         help
 815           Say "y" to generate the larger testing version of the
 816           File-backed Storage Gadget, useful for probing the
 817           behavior of USB Mass Storage hosts.  Not needed for
 818           normal operation.
 819
 820 config USB_MASS_STORAGE
 821         tristate "Mass Storage Gadget"
 822         depends on BLOCK
 823         help
 824           The Mass Storage Gadget acts as a USB Mass Storage disk drive.
 825           As its storage repository it can use a regular file or a block
 826           device (in much the same way as the "loop" device driver),
 827           specified as a module parameter or sysfs option.
 828
 829           This is heavily based on File-backed Storage Gadget and in most
 830           cases you will want to use FSG instead.  This gadget is mostly
 831           here to test the functionality of the Mass Storage Function
 832           which may be used with composite framework.
 833
 834           Say "y" to link the driver statically, or "m" to build
 835           a dynamically linked module called "g_mass_storage".  If unsure,
 836           consider File-backed Storage Gadget.
 837
 838 config USB_G_SERIAL
 839         tristate "Serial Gadget (with CDC ACM and CDC OBEX support)"
 840         help
 841           The Serial Gadget talks to the Linux-USB generic serial driver.
 842           This driver supports a CDC-ACM module option, which can be used
 843           to interoperate with MS-Windows hosts or with the Linux-USB
 844           "cdc-acm" driver.
 845
 846           This driver also supports a CDC-OBEX option.  You will need a
 847           user space OBEX server talking to /dev/ttyGS*, since the kernel
 848           itself doesn't implement the OBEX protocol.
 849
 850           Say "y" to link the driver statically, or "m" to build a
 851           dynamically linked module called "g_serial".
 852
 853           For more information, see Documentation/usb/gadget_serial.txt
 854           which includes instructions and a "driver info file" needed to
 855           make MS-Windows work with CDC ACM.
 856
 857 config USB_MIDI_GADGET
 858         tristate "MIDI Gadget (EXPERIMENTAL)"
 859         depends on SND && EXPERIMENTAL
 860         select SND_RAWMIDI
 861         help
 862           The MIDI Gadget acts as a USB Audio device, with one MIDI
 863           input and one MIDI output. These MIDI jacks appear as
 864           a sound "card" in the ALSA sound system. Other MIDI
 865           connections can then be made on the gadget system, using
 866           ALSA's aconnect utility etc.
 867
 868           Say "y" to link the driver statically, or "m" to build a
 869           dynamically linked module called "g_midi".
 870
 871 config USB_G_PRINTER
 872         tristate "Printer Gadget"
 873         help
 874           The Printer Gadget channels data between the USB host and a
 875           userspace program driving the print engine. The user space
 876           program reads and writes the device file /dev/g_printer to
 877           receive or send printer data. It can use ioctl calls to
 878           the device file to get or set printer status.
 879
 880           Say "y" to link the driver statically, or "m" to build a
 881           dynamically linked module called "g_printer".
 882
 883           For more information, see Documentation/usb/gadget_printer.txt
 884           which includes sample code for accessing the device file.
 885
 886 config USB_CDC_COMPOSITE
 887         tristate "CDC Composite Device (Ethernet and ACM)"
 888         depends on NET
 889         help
 890           This driver provides two functions in one configuration:
 891           a CDC Ethernet (ECM) link, and a CDC ACM (serial port) link.
 892
 893           This driver requires four bulk and two interrupt endpoints,
 894           plus the ability to handle altsettings.  Not all peripheral
 895           controllers are that capable.
 896
 897           Say "y" to link the driver statically, or "m" to build a
 898           dynamically linked module.
 899
 900 config USB_G_NOKIA
 901         tristate "Nokia composite gadget"
 902         depends on PHONET
 903         help
 904           The Nokia composite gadget provides support for acm, obex
 905           and phonet in only one composite gadget driver.
 906
 907           It's only really useful for N900 hardware. If you're building
 908           a kernel for N900, say Y or M here. If unsure, say N.
 909
 910 config USB_G_MULTI
 911         tristate "Multifunction Composite Gadget (EXPERIMENTAL)"
 912         depends on BLOCK && NET
 913         select USB_G_MULTI_CDC if !USB_G_MULTI_RNDIS
 914         help
 915           The Multifunction Composite Gadget provides Ethernet (RNDIS
 916           and/or CDC Ethernet), mass storage and ACM serial link
 917           interfaces.
 918
 919           You will be asked to choose which of the two configurations is
 920           to be available in the gadget.  At least one configuration must
 921           be chosen to make the gadget usable.  Selecting more than one
 922           configuration will prevent Windows from automatically detecting
 923           the gadget as a composite gadget, so an INF file will be needed to
 924           use the gadget.
 925
 926           Say "y" to link the driver statically, or "m" to build a
 927           dynamically linked module called "g_multi".
 928
 929 config USB_G_MULTI_RNDIS
 930         bool "RNDIS + CDC Serial + Storage configuration"
 931         depends on USB_G_MULTI
 932         default y
 933         help
 934           This option enables a configuration with RNDIS, CDC Serial and
 935           Mass Storage functions available in the Multifunction Composite
 936           Gadget.  This is the configuration dedicated for Windows since RNDIS
 937           is Microsoft's protocol.
 938
 939           If unsure, say "y".
 940
 941 config USB_G_MULTI_CDC
 942         bool "CDC Ethernet + CDC Serial + Storage configuration"
 943         depends on USB_G_MULTI
 944         default n
 945         help
 946           This option enables a configuration with CDC Ethernet (ECM), CDC
 947           Serial and Mass Storage functions available in the Multifunction
 948           Composite Gadget.
 949
 950           If unsure, say "y".
 951
 952 config USB_G_HID
 953         tristate "HID Gadget"
 954         help
 955           The HID gadget driver provides generic emulation of USB
 956           Human Interface Devices (HID).
 957
 958           For more information, see Documentation/usb/gadget_hid.txt which
 959           includes sample code for accessing the device files.
 960
 961           Say "y" to link the driver statically, or "m" to build a
 962           dynamically linked module called "g_hid".
 963
 964 config USB_G_DBGP
 965         tristate "EHCI Debug Device Gadget"
 966         help
 967           This gadget emulates an EHCI Debug device. This is useful when you want
 968           to interact with an EHCI Debug Port.
 969
 970           Say "y" to link the driver statically, or "m" to build a
 971           dynamically linked module called "g_dbgp".
 972
 973 if USB_G_DBGP
 974 choice
 975         prompt "EHCI Debug Device mode"
 976         default USB_G_DBGP_SERIAL
 977
 978 config USB_G_DBGP_PRINTK
 979         depends on USB_G_DBGP
 980         bool "printk"
 981         help
 982           Directly printk() received data. No interaction.
 983
 984 config USB_G_DBGP_SERIAL
 985         depends on USB_G_DBGP
 986         bool "serial"
 987         help
 988           Userland can interact using /dev/ttyGSxxx.
 989 endchoice
 990 endif
 991
 992 # put drivers that need isochronous transfer support (for audio
 993 # or video class gadget drivers), or specific hardware, here.
 994 config USB_G_WEBCAM
 995         tristate "USB Webcam Gadget"
 996         depends on VIDEO_DEV
 997         help
 998           The Webcam Gadget acts as a composite USB Audio and Video Class
 999           device. It provides a userspace API to process UVC control requests
1000           and stream video data to the host.
1001
1002           Say "y" to link the driver statically, or "m" to build a
1003           dynamically linked module called "g_webcam".
1004
1005 endchoice
1006
1007 endif # USB_GADGET