drivers/usb/host/ohci-omap.c

   1 /*
   2  * OHCI HCD (Host Controller Driver) for USB.
   3  *
   4  * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
   5  * (C) Copyright 2000-2005 David Brownell
   6  * (C) Copyright 2002 Hewlett-Packard Company
   7  *
   8  * OMAP Bus Glue
   9  *
  10  * Modified for OMAP by Tony Lindgren <tony@atomide.com>
  11  * Based on the 2.4 OMAP OHCI driver originally done by MontaVista Software Inc.
  12  * and on ohci-sa1111.c by Christopher Hoover <ch@hpl.hp.com>
  13  *
  14  * This file is licenced under the GPL.
  15  */
  16
  17 #include <linux/signal.h>       /* SA_INTERRUPT */
  18 #include <linux/jiffies.h>
  19
  20 #include <asm/hardware.h>
  21 #include <asm/io.h>
  22 #include <asm/mach-types.h>
  23
  24 #include <asm/arch/mux.h>
  25 #include <asm/arch/irqs.h>
  26 #include <asm/arch/gpio.h>
  27 #include <asm/arch/fpga.h>
  28 #include <asm/arch/usb.h>
  29 #include <asm/hardware/clock.h>
  30
  31
  32 /* OMAP-1510 OHCI has its own MMU for DMA */
  33 #define OMAP1510_LB_MEMSIZE     32      /* Should be same as SDRAM size */
  34 #define OMAP1510_LB_CLOCK_DIV   0xfffec10c
  35 #define OMAP1510_LB_MMU_CTL     0xfffec208
  36 #define OMAP1510_LB_MMU_LCK     0xfffec224
  37 #define OMAP1510_LB_MMU_LD_TLB  0xfffec228
  38 #define OMAP1510_LB_MMU_CAM_H   0xfffec22c
  39 #define OMAP1510_LB_MMU_CAM_L   0xfffec230
  40 #define OMAP1510_LB_MMU_RAM_H   0xfffec234
  41 #define OMAP1510_LB_MMU_RAM_L   0xfffec238
  42
  43
  44 #ifndef CONFIG_ARCH_OMAP
  45 #error "This file is OMAP bus glue.  CONFIG_OMAP must be defined."
  46 #endif
  47
  48 #ifdef CONFIG_TPS65010
  49 #include <asm/arch/tps65010.h>
  50 #else
  51
  52 #define LOW     0
  53 #define HIGH    1
  54
  55 #define GPIO1   1
  56
  57 static inline int tps65010_set_gpio_out_value(unsigned gpio, unsigned value)
  58 {
  59         return 0;
  60 }
  61
  62 #endif
  63
  64 extern int usb_disabled(void);
  65 extern int ocpi_enable(void);
  66
  67 static struct clk *usb_host_ck;
  68
  69 static void omap_ohci_clock_power(int on)
  70 {
  71         if (on) {
  72                 clk_enable(usb_host_ck);
  73                 /* guesstimate for T5 == 1x 32K clock + APLL lock time */
  74                 udelay(100);
  75         } else {
  76                 clk_disable(usb_host_ck);
  77         }
  78 }
  79
  80 /*
  81  * Board specific gang-switched transceiver power on/off.
  82  * NOTE:  OSK supplies power from DC, not battery.
  83  */
  84 static int omap_ohci_transceiver_power(int on)
  85 {
  86         if (on) {
  87                 if (machine_is_omap_innovator() && cpu_is_omap1510())
  88                         fpga_write(fpga_read(INNOVATOR_FPGA_CAM_USB_CONTROL)
  89                                 | ((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
  90                                INNOVATOR_FPGA_CAM_USB_CONTROL);
  91                 else if (machine_is_omap_osk())
  92                         tps65010_set_gpio_out_value(GPIO1, LOW);
  93         } else {
  94                 if (machine_is_omap_innovator() && cpu_is_omap1510())
  95                         fpga_write(fpga_read(INNOVATOR_FPGA_CAM_USB_CONTROL)
  96                                 & ~((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
  97                                INNOVATOR_FPGA_CAM_USB_CONTROL);
  98                 else if (machine_is_omap_osk())
  99                         tps65010_set_gpio_out_value(GPIO1, HIGH);
 100         }
 101
 102         return 0;
 103 }
 104
 105 /*
 106  * OMAP-1510 specific Local Bus clock on/off
 107  */
 108 static int omap_1510_local_bus_power(int on)
 109 {
 110         if (on) {
 111                 omap_writel((1 << 1) | (1 << 0), OMAP1510_LB_MMU_CTL);
 112                 udelay(200);
 113         } else {
 114                 omap_writel(0, OMAP1510_LB_MMU_CTL);
 115         }
 116
 117         return 0;
 118 }
 119
 120 /*
 121  * OMAP-1510 specific Local Bus initialization
 122  * NOTE: This assumes 32MB memory size in OMAP1510LB_MEMSIZE.
 123  *       See also arch/mach-omap/memory.h for __virt_to_dma() and
 124  *       __dma_to_virt() which need to match with the physical
 125  *       Local Bus address below.
 126  */
 127 static int omap_1510_local_bus_init(void)
 128 {
 129         unsigned int tlb;
 130         unsigned long lbaddr, physaddr;
 131
 132         omap_writel((omap_readl(OMAP1510_LB_CLOCK_DIV) & 0xfffffff8) | 0x4,
 133                OMAP1510_LB_CLOCK_DIV);
 134
 135         /* Configure the Local Bus MMU table */
 136         for (tlb = 0; tlb < OMAP1510_LB_MEMSIZE; tlb++) {
 137                 lbaddr = tlb * 0x00100000 + OMAP1510_LB_OFFSET;
 138                 physaddr = tlb * 0x00100000 + PHYS_OFFSET;
 139                 omap_writel((lbaddr & 0x0fffffff) >> 22, OMAP1510_LB_MMU_CAM_H);
 140                 omap_writel(((lbaddr & 0x003ffc00) >> 6) | 0xc,
 141                        OMAP1510_LB_MMU_CAM_L);
 142                 omap_writel(physaddr >> 16, OMAP1510_LB_MMU_RAM_H);
 143                 omap_writel((physaddr & 0x0000fc00) | 0x300, OMAP1510_LB_MMU_RAM_L);
 144                 omap_writel(tlb << 4, OMAP1510_LB_MMU_LCK);
 145                 omap_writel(0x1, OMAP1510_LB_MMU_LD_TLB);
 146         }
 147
 148         /* Enable the walking table */
 149         omap_writel(omap_readl(OMAP1510_LB_MMU_CTL) | (1 << 3), OMAP1510_LB_MMU_CTL);
 150         udelay(200);
 151
 152         return 0;
 153 }
 154
 155 #ifdef  CONFIG_USB_OTG
 156
 157 static void start_hnp(struct ohci_hcd *ohci)
 158 {
 159         const unsigned  port = ohci_to_hcd(ohci)->self.otg_port - 1;
 160         unsigned long   flags;
 161
 162         otg_start_hnp(ohci->transceiver);
 163
 164         local_irq_save(flags);
 165         ohci->transceiver->state = OTG_STATE_A_SUSPEND;
 166         writel (RH_PS_PSS, &ohci->regs->roothub.portstatus [port]);
 167         OTG_CTRL_REG &= ~OTG_A_BUSREQ;
 168         local_irq_restore(flags);
 169 }
 170
 171 #endif
 172
 173 /*-------------------------------------------------------------------------*/
 174
 175 static int omap_start_hc(struct ohci_hcd *ohci, struct platform_device *pdev)
 176 {
 177         struct omap_usb_config  *config = pdev->dev.platform_data;
 178         int                     need_transceiver = (config->otg != 0);
 179         int                     ret;
 180
 181         dev_dbg(&pdev->dev, "starting USB Controller\n");
 182
 183         if (config->otg) {
 184                 ohci_to_hcd(ohci)->self.otg_port = config->otg;
 185                 /* default/minimum OTG power budget:  8 mA */
 186                 ohci_to_hcd(ohci)->power_budget = 8;
 187         }
 188
 189         /* boards can use OTG transceivers in non-OTG modes */
 190         need_transceiver = need_transceiver
 191                         || machine_is_omap_h2() || machine_is_omap_h3();
 192
 193         if (cpu_is_omap16xx())
 194                 ocpi_enable();
 195
 196 #ifdef  CONFIG_ARCH_OMAP_OTG
 197         if (need_transceiver) {
 198                 ohci->transceiver = otg_get_transceiver();
 199                 if (ohci->transceiver) {
 200                         int     status = otg_set_host(ohci->transceiver,
 201                                                 &ohci_to_hcd(ohci)->self);
 202                         dev_dbg(&pdev->dev, "init %s transceiver, status %d\n",
 203                                         ohci->transceiver->label, status);
 204                         if (status) {
 205                                 if (ohci->transceiver)
 206                                         put_device(ohci->transceiver->dev);
 207                                 return status;
 208                         }
 209                 } else {
 210                         dev_err(&pdev->dev, "can't find transceiver\n");
 211                         return -ENODEV;
 212                 }
 213         }
 214 #endif
 215
 216         omap_ohci_clock_power(1);
 217
 218         if (cpu_is_omap1510()) {
 219                 omap_1510_local_bus_power(1);
 220                 omap_1510_local_bus_init();
 221         }
 222
 223         if ((ret = ohci_init(ohci)) < 0)
 224                 return ret;
 225
 226         /* board-specific power switching and overcurrent support */
 227         if (machine_is_omap_osk() || machine_is_omap_innovator()) {
 228                 u32     rh = roothub_a (ohci);
 229
 230                 /* power switching (ganged by default) */
 231                 rh &= ~RH_A_NPS;
 232
 233                 /* TPS2045 switch for internal transceiver (port 1) */
 234                 if (machine_is_omap_osk()) {
 235                         ohci_to_hcd(ohci)->power_budget = 250;
 236
 237                         rh &= ~RH_A_NOCP;
 238
 239                         /* gpio9 for overcurrent detction */
 240                         omap_cfg_reg(W8_1610_GPIO9);
 241                         omap_request_gpio(9);
 242                         omap_set_gpio_direction(9, 1 /* IN */);
 243
 244                         /* for paranoia's sake:  disable USB.PUEN */
 245                         omap_cfg_reg(W4_USB_HIGHZ);
 246                 }
 247                 ohci_writel(ohci, rh, &ohci->regs->roothub.a);
 248                 distrust_firmware = 0;
 249         }
 250
 251         /* FIXME khubd hub requests should manage power switching */
 252         omap_ohci_transceiver_power(1);
 253
 254         /* board init will have already handled HMC and mux setup.
 255          * any external transceiver should already be initialized
 256          * too, so all configured ports use the right signaling now.
 257          */
 258
 259         return 0;
 260 }
 261
 262 static void omap_stop_hc(struct platform_device *pdev)
 263 {
 264         dev_dbg(&pdev->dev, "stopping USB Controller\n");
 265         omap_ohci_clock_power(0);
 266 }
 267
 268
 269 /*-------------------------------------------------------------------------*/
 270
 271 void usb_hcd_omap_remove (struct usb_hcd *, struct platform_device *);
 272
 273 /* configure so an HC device and id are always provided */
 274 /* always called with process context; sleeping is OK */
 275
 276
 277 /**
 278  * usb_hcd_omap_probe - initialize OMAP-based HCDs
 279  * Context: !in_interrupt()
 280  *
 281  * Allocates basic resources for this USB host controller, and
 282  * then invokes the start() method for the HCD associated with it
 283  * through the hotplug entry's driver_data.
 284  */
 285 int usb_hcd_omap_probe (const struct hc_driver *driver,
 286                           struct platform_device *pdev)
 287 {
 288         int retval;
 289         struct usb_hcd *hcd = 0;
 290         struct ohci_hcd *ohci;
 291
 292         if (pdev->num_resources != 2) {
 293                 printk(KERN_ERR "hcd probe: invalid num_resources: %i\n",
 294                        pdev->num_resources);
 295                 return -ENODEV;
 296         }
 297
 298         if (pdev->resource[0].flags != IORESOURCE_MEM
 299                         || pdev->resource[1].flags != IORESOURCE_IRQ) {
 300                 printk(KERN_ERR "hcd probe: invalid resource type\n");
 301                 return -ENODEV;
 302         }
 303
 304         usb_host_ck = clk_get(0, "usb_hhc_ck");
 305         if (IS_ERR(usb_host_ck))
 306                 return PTR_ERR(usb_host_ck);
 307
 308         hcd = usb_create_hcd (driver, &pdev->dev, pdev->dev.bus_id);
 309         if (!hcd) {
 310                 retval = -ENOMEM;
 311                 goto err0;
 312         }
 313         hcd->rsrc_start = pdev->resource[0].start;
 314         hcd->rsrc_len = pdev->resource[0].end - pdev->resource[0].start + 1;
 315
 316         if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
 317                 dev_dbg(&pdev->dev, "request_mem_region failed\n");
 318                 retval = -EBUSY;
 319                 goto err1;
 320         }
 321
 322         hcd->regs = (void __iomem *) (int) IO_ADDRESS(hcd->rsrc_start);
 323
 324         ohci = hcd_to_ohci(hcd);
 325         ohci_hcd_init(ohci);
 326
 327         retval = omap_start_hc(ohci, pdev);
 328         if (retval < 0)
 329                 goto err2;
 330
 331         retval = usb_add_hcd(hcd, platform_get_irq(pdev, 0), SA_INTERRUPT);
 332         if (retval == 0)
 333                 return retval;
 334
 335         omap_stop_hc(pdev);
 336 err2:
 337         release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
 338 err1:
 339         usb_put_hcd(hcd);
 340 err0:
 341         clk_put(usb_host_ck);
 342         return retval;
 343 }
 344
 345
 346 /* may be called with controller, bus, and devices active */
 347
 348 /**
 349  * usb_hcd_omap_remove - shutdown processing for OMAP-based HCDs
 350  * @dev: USB Host Controller being removed
 351  * Context: !in_interrupt()
 352  *
 353  * Reverses the effect of usb_hcd_omap_probe(), first invoking
 354  * the HCD's stop() method.  It is always called from a thread
 355  * context, normally "rmmod", "apmd", or something similar.
 356  *
 357  */
 358 void usb_hcd_omap_remove (struct usb_hcd *hcd, struct platform_device *pdev)
 359 {
 360         usb_remove_hcd(hcd);
 361         if (machine_is_omap_osk())
 362                 omap_free_gpio(9);
 363         omap_stop_hc(pdev);
 364         release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
 365         usb_put_hcd(hcd);
 366         clk_put(usb_host_ck);
 367 }
 368
 369 /*-------------------------------------------------------------------------*/
 370
 371 static int __devinit
 372 ohci_omap_start (struct usb_hcd *hcd)
 373 {
 374         struct omap_usb_config *config;
 375         struct ohci_hcd *ohci = hcd_to_ohci (hcd);
 376         int             ret;
 377
 378         config = hcd->self.controller->platform_data;
 379         if (config->otg || config->rwc)
 380                 writel(OHCI_CTRL_RWC, &ohci->regs->control);
 381
 382         if ((ret = ohci_run (ohci)) < 0) {
 383                 dev_err(hcd->self.controller, "can't start\n");
 384                 ohci_stop (hcd);
 385                 return ret;
 386         }
 387         return 0;
 388 }
 389
 390 /*-------------------------------------------------------------------------*/
 391
 392 static const struct hc_driver ohci_omap_hc_driver = {
 393         .description =          hcd_name,
 394         .product_desc =         "OMAP OHCI",
 395         .hcd_priv_size =        sizeof(struct ohci_hcd),
 396
 397         /*
 398          * generic hardware linkage
 399          */
 400         .irq =                  ohci_irq,
 401         .flags =                HCD_USB11 | HCD_MEMORY,
 402
 403         /*
 404          * basic lifecycle operations
 405          */
 406         .start =                ohci_omap_start,
 407         .stop =                 ohci_stop,
 408
 409         /*
 410          * managing i/o requests and associated device resources
 411          */
 412         .urb_enqueue =          ohci_urb_enqueue,
 413         .urb_dequeue =          ohci_urb_dequeue,
 414         .endpoint_disable =     ohci_endpoint_disable,
 415
 416         /*
 417          * scheduling support
 418          */
 419         .get_frame_number =     ohci_get_frame,
 420
 421         /*
 422          * root hub support
 423          */
 424         .hub_status_data =      ohci_hub_status_data,
 425         .hub_control =          ohci_hub_control,
 426 #ifdef  CONFIG_PM
 427         .bus_suspend =          ohci_bus_suspend,
 428         .bus_resume =           ohci_bus_resume,
 429 #endif
 430         .start_port_reset =     ohci_start_port_reset,
 431 };
 432
 433 /*-------------------------------------------------------------------------*/
 434
 435 static int ohci_hcd_omap_drv_probe(struct device *dev)
 436 {
 437         return usb_hcd_omap_probe(&ohci_omap_hc_driver,
 438                                 to_platform_device(dev));
 439 }
 440
 441 static int ohci_hcd_omap_drv_remove(struct device *dev)
 442 {
 443         struct platform_device  *pdev = to_platform_device(dev);
 444         struct usb_hcd          *hcd = dev_get_drvdata(dev);
 445         struct ohci_hcd         *ohci = hcd_to_ohci (hcd);
 446
 447         usb_hcd_omap_remove(hcd, pdev);
 448         if (ohci->transceiver) {
 449                 (void) otg_set_host(ohci->transceiver, 0);
 450                 put_device(ohci->transceiver->dev);
 451         }
 452         dev_set_drvdata(dev, NULL);
 453
 454         return 0;
 455 }
 456
 457 /*-------------------------------------------------------------------------*/
 458
 459 #ifdef  CONFIG_PM
 460
 461 static int ohci_omap_suspend(struct device *dev, pm_message_t message)
 462 {
 463         struct ohci_hcd *ohci = hcd_to_ohci(dev_get_drvdata(dev));
 464
 465         if (time_before(jiffies, ohci->next_statechange))
 466                 msleep(5);
 467         ohci->next_statechange = jiffies;
 468
 469         omap_ohci_clock_power(0);
 470         ohci_to_hcd(ohci)->state = HC_STATE_SUSPENDED;
 471         dev->power.power_state = PMSG_SUSPEND;
 472         return 0;
 473 }
 474
 475 static int ohci_omap_resume(struct device *dev)
 476 {
 477         struct ohci_hcd *ohci = hcd_to_ohci(dev_get_drvdata(dev));
 478
 479         if (time_before(jiffies, ohci->next_statechange))
 480                 msleep(5);
 481         ohci->next_statechange = jiffies;
 482
 483         omap_ohci_clock_power(1);
 484         dev->power.power_state = PMSG_ON;
 485         usb_hcd_resume_root_hub(dev_get_drvdata(dev));
 486         return 0;
 487 }
 488
 489 #endif
 490
 491 /*-------------------------------------------------------------------------*/
 492
 493 /*
 494  * Driver definition to register with the OMAP bus
 495  */
 496 static struct device_driver ohci_hcd_omap_driver = {
 497         .name           = "ohci",
 498         .owner          = THIS_MODULE,
 499         .bus            = &platform_bus_type,
 500         .probe          = ohci_hcd_omap_drv_probe,
 501         .remove         = ohci_hcd_omap_drv_remove,
 502 #ifdef  CONFIG_PM
 503         .suspend        = ohci_omap_suspend,
 504         .resume         = ohci_omap_resume,
 505 #endif
 506 };
 507
 508 static int __init ohci_hcd_omap_init (void)
 509 {
 510         printk (KERN_DEBUG "%s: " DRIVER_INFO " (OMAP)\n", hcd_name);
 511         if (usb_disabled())
 512                 return -ENODEV;
 513
 514         pr_debug("%s: block sizes: ed %Zd td %Zd\n", hcd_name,
 515                 sizeof (struct ed), sizeof (struct td));
 516
 517         return driver_register(&ohci_hcd_omap_driver);
 518 }
 519
 520 static void __exit ohci_hcd_omap_cleanup (void)
 521 {
 522         driver_unregister(&ohci_hcd_omap_driver);
 523 }
 524
 525 module_init (ohci_hcd_omap_init);
 526 module_exit (ohci_hcd_omap_cleanup);