drivers/usb/otg/Kconfig

   1 #
   2 # USB OTG infrastructure may be needed for peripheral-only, host-only,
   3 # or OTG-capable configurations when OTG transceivers or controllers
   4 # are used.
   5 #
   6
   7 comment "OTG and related infrastructure"
   8
   9 config USB_OTG_UTILS
  10         bool
  11         help
  12           Select this to make sure the build includes objects from
  13           the OTG infrastructure directory.
  14
  15 if USB || USB_GADGET
  16
  17 #
  18 # USB Transceiver Drivers
  19 #
  20 config USB_GPIO_VBUS
  21         tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
  22         depends on GENERIC_GPIO
  23         select USB_OTG_UTILS
  24         help
  25           Provides simple GPIO VBUS sensing for controllers with an
  26           internal transceiver via the usb_phy interface, and
  27           optionally control of a D+ pullup GPIO as well as a VBUS
  28           current limit regulator.
  29
  30 config ISP1301_OMAP
  31         tristate "Philips ISP1301 with OMAP OTG"
  32         depends on I2C && ARCH_OMAP_OTG
  33         select USB_OTG_UTILS
  34         help
  35           If you say yes here you get support for the Philips ISP1301
  36           USB-On-The-Go transceiver working with the OMAP OTG controller.
  37           The ISP1301 is a full speed USB  transceiver which is used in
  38           products including H2, H3, and H4 development boards for Texas
  39           Instruments OMAP processors.
  40
  41           This driver can also be built as a module.  If so, the module
  42           will be called isp1301_omap.
  43
  44 config USB_ULPI
  45         bool "Generic ULPI Transceiver Driver"
  46         depends on ARM
  47         select USB_OTG_UTILS
  48         help
  49           Enable this to support ULPI connected USB OTG transceivers which
  50           are likely found on embedded boards.
  51
  52 config USB_ULPI_VIEWPORT
  53         bool
  54         depends on USB_ULPI
  55         help
  56           Provides read/write operations to the ULPI phy register set for
  57           controllers with a viewport register (e.g. Chipidea/ARC controllers).
  58
  59 config TWL4030_USB
  60         tristate "TWL4030 USB Transceiver Driver"
  61         depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
  62         select USB_OTG_UTILS
  63         help
  64           Enable this to support the USB OTG transceiver on TWL4030
  65           family chips (including the TWL5030 and TPS659x0 devices).
  66           This transceiver supports high and full speed devices plus,
  67           in host mode, low speed.
  68
  69 config TWL6030_USB
  70         tristate "TWL6030 USB Transceiver Driver"
  71         depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
  72         select USB_OTG_UTILS
  73         help
  74           Enable this to support the USB OTG transceiver on TWL6030
  75           family chips. This TWL6030 transceiver has the VBUS and ID GND
  76           and OTG SRP events capabilities. For all other transceiver functionality
  77           UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
  78           are hooked to this driver through platform_data structure.
  79           The definition of internal PHY APIs are in the mach-omap2 layer.
  80
  81 config NOP_USB_XCEIV
  82         tristate "NOP USB Transceiver Driver"
  83         select USB_OTG_UTILS
  84         help
  85           This driver is to be used by all the usb transceiver which are either
  86           built-in with usb ip or which are autonomous and doesn't require any
  87           phy programming such as ISP1x04 etc.
  88
  89 config USB_MSM_OTG
  90         tristate "OTG support for Qualcomm on-chip USB controller"
  91         depends on (USB || USB_GADGET) && ARCH_MSM
  92         select USB_OTG_UTILS
  93         help
  94           Enable this to support the USB OTG transceiver on MSM chips. It
  95           handles PHY initialization, clock management, and workarounds
  96           required after resetting the hardware and power management.
  97           This driver is required even for peripheral only or host only
  98           mode configurations.
  99           This driver is not supported on boards like trout which
 100           has an external PHY.
 101
 102 config AB8500_USB
 103         tristate "AB8500 USB Transceiver Driver"
 104         depends on AB8500_CORE
 105         select USB_OTG_UTILS
 106         help
 107           Enable this to support the USB OTG transceiver in AB8500 chip.
 108           This transceiver supports high and full speed devices plus,
 109           in host mode, low speed.
 110
 111 config FSL_USB2_OTG
 112         bool "Freescale USB OTG Transceiver Driver"
 113         depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_SUSPEND
 114         select USB_OTG
 115         select USB_OTG_UTILS
 116         help
 117           Enable this to support Freescale USB OTG transceiver.
 118
 119 config USB_MXS_PHY
 120         tristate "Freescale MXS USB PHY support"
 121         depends on ARCH_MXC || ARCH_MXS
 122         select STMP_DEVICE
 123         select USB_OTG_UTILS
 124         help
 125           Enable this to support the Freescale MXS USB PHY.
 126
 127           MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
 128
 129 config USB_MV_OTG
 130         tristate "Marvell USB OTG support"
 131         depends on USB_EHCI_MV && USB_MV_UDC && USB_SUSPEND
 132         select USB_OTG
 133         select USB_OTG_UTILS
 134         help
 135           Say Y here if you want to build Marvell USB OTG transciever
 136           driver in kernel (including PXA and MMP series). This driver
 137           implements role switch between EHCI host driver and gadget driver.
 138
 139           To compile this driver as a module, choose M here.
 140
 141 endif # USB || OTG