drivers/usb/phy/Kconfig

   1 #
   2 # Physical Layer USB driver configuration
   3 #
   4 menu "USB Physical Layer drivers"
   5
   6 config USB_PHY
   7         def_bool n
   8
   9 config USB_OTG_FSM
  10         tristate "USB 2.0 OTG FSM implementation"
  11         depends on USB
  12         select USB_OTG
  13         select USB_PHY
  14         help
  15           Implements OTG Final State Machine as specified in On-The-Go
  16           and Embedded Host Supplement to the USB Revision 2.0 Specification.
  17
  18 #
  19 # USB Transceiver Drivers
  20 #
  21 config AB8500_USB
  22         tristate "AB8500 USB Transceiver Driver"
  23         depends on AB8500_CORE
  24         select USB_PHY
  25         help
  26           Enable this to support the USB OTG transceiver in AB8500 chip.
  27           This transceiver supports high and full speed devices plus,
  28           in host mode, low speed.
  29
  30 config FSL_USB2_OTG
  31         bool "Freescale USB OTG Transceiver Driver"
  32         depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM_RUNTIME
  33         select USB_OTG
  34         select USB_PHY
  35         help
  36           Enable this to support Freescale USB OTG transceiver.
  37
  38 config ISP1301_OMAP
  39         tristate "Philips ISP1301 with OMAP OTG"
  40         depends on I2C && ARCH_OMAP_OTG
  41         depends on USB
  42         select USB_PHY
  43         help
  44           If you say yes here you get support for the Philips ISP1301
  45           USB-On-The-Go transceiver working with the OMAP OTG controller.
  46           The ISP1301 is a full speed USB  transceiver which is used in
  47           products including H2, H3, and H4 development boards for Texas
  48           Instruments OMAP processors.
  49
  50           This driver can also be built as a module.  If so, the module
  51           will be called phy-isp1301-omap.
  52
  53 config KEYSTONE_USB_PHY
  54         tristate "Keystone USB PHY Driver"
  55         depends on ARCH_KEYSTONE || COMPILE_TEST
  56         select NOP_USB_XCEIV
  57         help
  58           Enable this to support Keystone USB phy. This driver provides
  59           interface to interact with USB 2.0 and USB 3.0 PHY that is part
  60           of the Keystone SOC.
  61
  62 config MV_U3D_PHY
  63         bool "Marvell USB 3.0 PHY controller Driver"
  64         depends on CPU_MMP3
  65         select USB_PHY
  66         help
  67           Enable this to support Marvell USB 3.0 phy controller for Marvell
  68           SoC.
  69
  70 config NOP_USB_XCEIV
  71         tristate "NOP USB Transceiver Driver"
  72         select USB_PHY
  73         help
  74           This driver is to be used by all the usb transceiver which are either
  75           built-in with usb ip or which are autonomous and doesn't require any
  76           phy programming such as ISP1x04 etc.
  77
  78 config OMAP_CONTROL_USB
  79         tristate "OMAP CONTROL USB Driver"
  80         depends on ARCH_OMAP2PLUS || COMPILE_TEST
  81         help
  82           Enable this to add support for the USB part present in the control
  83           module. This driver has API to power on the USB2 PHY and to write to
  84           the mailbox. The mailbox is present only in omap4 and the register to
  85           power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an
  86           additional register to power on USB3 PHY.
  87
  88 config AM335X_CONTROL_USB
  89         tristate
  90
  91 config AM335X_PHY_USB
  92         tristate "AM335x USB PHY Driver"
  93         depends on ARM || COMPILE_TEST
  94         select USB_PHY
  95         select AM335X_CONTROL_USB
  96         select NOP_USB_XCEIV
  97         help
  98           This driver provides PHY support for that phy which part for the
  99           AM335x SoC.
 100
 101 config SAMSUNG_USBPHY
 102         tristate
 103         help
 104           Enable this to support Samsung USB phy helper driver for Samsung SoCs.
 105           This driver provides common interface to interact, for Samsung USB 2.0 PHY
 106           driver and later for Samsung USB 3.0 PHY driver.
 107
 108 config SAMSUNG_USB2PHY
 109         tristate "Samsung USB 2.0 PHY controller Driver"
 110         select SAMSUNG_USBPHY
 111         select USB_PHY
 112         help
 113           Enable this to support Samsung USB 2.0 (High Speed) PHY controller
 114           driver for Samsung SoCs.
 115
 116 config SAMSUNG_USB3PHY
 117         tristate "Samsung USB 3.0 PHY controller Driver"
 118         select SAMSUNG_USBPHY
 119         select USB_PHY
 120         help
 121           Enable this to support Samsung USB 3.0 (Super Speed) phy controller
 122           for samsung SoCs.
 123
 124 config TWL6030_USB
 125         tristate "TWL6030 USB Transceiver Driver"
 126         depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
 127         help
 128           Enable this to support the USB OTG transceiver on TWL6030
 129           family chips. This TWL6030 transceiver has the VBUS and ID GND
 130           and OTG SRP events capabilities. For all other transceiver functionality
 131           UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
 132           are hooked to this driver through platform_data structure.
 133           The definition of internal PHY APIs are in the mach-omap2 layer.
 134
 135 config USB_GPIO_VBUS
 136         tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
 137         depends on GPIOLIB
 138         select USB_PHY
 139         help
 140           Provides simple GPIO VBUS sensing for controllers with an
 141           internal transceiver via the usb_phy interface, and
 142           optionally control of a D+ pullup GPIO as well as a VBUS
 143           current limit regulator.
 144
 145 config OMAP_OTG
 146         tristate "OMAP USB OTG controller driver"
 147         depends on ARCH_OMAP_OTG && EXTCON
 148         help
 149           Enable this to support some transceivers on OMAP1 platforms. OTG
 150           controller is needed to switch between host and peripheral modes.
 151
 152           This driver can also be built as a module. If so, the module
 153           will be called phy-omap-otg.
 154
 155 config TAHVO_USB
 156         tristate "Tahvo USB transceiver driver"
 157         depends on MFD_RETU && EXTCON
 158         select USB_PHY
 159         help
 160           Enable this to support USB transceiver on Tahvo. This is used
 161           at least on Nokia 770.
 162
 163 config TAHVO_USB_HOST_BY_DEFAULT
 164         depends on TAHVO_USB
 165         boolean "Device in USB host mode by default"
 166         help
 167           Say Y here, if you want the device to enter USB host mode
 168           by default on bootup.
 169
 170 config USB_ISP1301
 171         tristate "NXP ISP1301 USB transceiver support"
 172         depends on USB || USB_GADGET
 173         depends on I2C
 174         select USB_PHY
 175         help
 176           Say Y here to add support for the NXP ISP1301 USB transceiver driver.
 177           This chip is typically used as USB transceiver for USB host, gadget
 178           and OTG drivers (to be selected separately).
 179
 180           To compile this driver as a module, choose M here: the
 181           module will be called phy-isp1301.
 182
 183 config USB_MSM_OTG
 184         tristate "OTG support for Qualcomm on-chip USB controller"
 185         depends on (USB || USB_GADGET) && ARCH_MSM
 186         select USB_PHY
 187         help
 188           Enable this to support the USB OTG transceiver on MSM chips. It
 189           handles PHY initialization, clock management, and workarounds
 190           required after resetting the hardware and power management.
 191           This driver is required even for peripheral only or host only
 192           mode configurations.
 193           This driver is not supported on boards like trout which
 194           has an external PHY.
 195
 196 config USB_MV_OTG
 197         tristate "Marvell USB OTG support"
 198         depends on USB_EHCI_MV && USB_MV_UDC && PM_RUNTIME
 199         select USB_OTG
 200         select USB_PHY
 201         help
 202           Say Y here if you want to build Marvell USB OTG transciever
 203           driver in kernel (including PXA and MMP series). This driver
 204           implements role switch between EHCI host driver and gadget driver.
 205
 206           To compile this driver as a module, choose M here.
 207
 208 config USB_MXS_PHY
 209         tristate "Freescale MXS USB PHY support"
 210         depends on ARCH_MXC || ARCH_MXS
 211         select STMP_DEVICE
 212         select USB_PHY
 213         help
 214           Enable this to support the Freescale MXS USB PHY.
 215
 216           MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
 217
 218 config USB_RCAR_PHY
 219         tristate "Renesas R-Car USB PHY support"
 220         depends on USB || USB_GADGET
 221         select USB_PHY
 222         help
 223           Say Y here to add support for the Renesas R-Car USB common PHY driver.
 224           This chip is typically used as USB PHY for USB host, gadget.
 225           This driver supports R8A7778 and R8A7779.
 226
 227           To compile this driver as a module, choose M here: the
 228           module will be called phy-rcar-usb.
 229
 230 config USB_RCAR_GEN2_PHY
 231         tristate "Renesas R-Car Gen2 USB PHY support"
 232         depends on ARCH_R8A7790 || ARCH_R8A7791 || COMPILE_TEST
 233         select USB_PHY
 234         help
 235           Say Y here to add support for the Renesas R-Car Gen2 USB PHY driver.
 236           It is typically used to control internal USB PHY for USBHS,
 237           and to configure shared USB channels 0 and 2.
 238           This driver supports R8A7790 and R8A7791.
 239
 240           To compile this driver as a module, choose M here: the
 241           module will be called phy-rcar-gen2-usb.
 242
 243 config USB_ULPI
 244         bool "Generic ULPI Transceiver Driver"
 245         depends on ARM
 246         help
 247           Enable this to support ULPI connected USB OTG transceivers which
 248           are likely found on embedded boards.
 249
 250 config USB_ULPI_VIEWPORT
 251         bool
 252         depends on USB_ULPI
 253         help
 254           Provides read/write operations to the ULPI phy register set for
 255           controllers with a viewport register (e.g. Chipidea/ARC controllers).
 256
 257 endmenu