drivers/usb/serial/ftdi_sio.h

   1 /*
   2  * Definitions for the FTDI USB Single Port Serial Converter -
   3  * known as FTDI_SIO (Serial Input/Output application of the chipset)
   4  *
   5  * The example I have is known as the USC-1000 which is available from
   6  * http://www.dse.co.nz - cat no XH4214 It looks similar to this:
   7  * http://www.dansdata.com/usbser.htm but I can't be sure There are other
   8  * USC-1000s which don't look like my device though so beware!
   9  *
  10  * The device is based on the FTDI FT8U100AX chip. It has a DB25 on one side,
  11  * USB on the other.
  12  *
  13  * Thanx to FTDI (http://www.ftdi.co.uk) for so kindly providing details
  14  * of the protocol required to talk to the device and ongoing assistence
  15  * during development.
  16  *
  17  * Bill Ryder - bryder@sgi.com formerly of Silicon Graphics, Inc.- wrote the
  18  * FTDI_SIO implementation.
  19  *
  20  * Philipp Gühring - pg@futureware.at - added the Device ID of the USB relais
  21  * from Rudolf Gugler
  22  *
  23  */
  24
  25 #define FTDI_VID        0x0403  /* Vendor Id */
  26 #define FTDI_SIO_PID    0x8372  /* Product Id SIO application of 8U100AX  */
  27 #define FTDI_8U232AM_PID 0x6001 /* Similar device to SIO above */
  28 #define FTDI_8U232AM_ALT_PID 0x6006 /* FTDI's alternate PID for above */
  29 #define FTDI_8U2232C_PID 0x6010 /* Dual channel device */
  30 #define FTDI_RELAIS_PID 0xFA10  /* Relais device from Rudolf Gugler */
  31 #define FTDI_NF_RIC_VID 0x0DCD  /* Vendor Id */
  32 #define FTDI_NF_RIC_PID 0x0001  /* Product Id */
  33
  34 /* www.irtrans.de device */
  35 #define FTDI_IRTRANS_PID 0xFC60 /* Product Id */
  36
  37 /* www.crystalfontz.com devices - thanx for providing free devices for evaluation ! */
  38 /* they use the ftdi chipset for the USB interface and the vendor id is the same */
  39 #define FTDI_XF_632_PID 0xFC08  /* 632: 16x2 Character Display */
  40 #define FTDI_XF_634_PID 0xFC09  /* 634: 20x4 Character Display */
  41 #define FTDI_XF_547_PID 0xFC0A  /* 547: Two line Display */
  42 #define FTDI_XF_633_PID 0xFC0B  /* 633: 16x2 Character Display with Keys */
  43 #define FTDI_XF_631_PID 0xFC0C  /* 631: 20x2 Character Display */
  44 #define FTDI_XF_635_PID 0xFC0D  /* 635: 20x4 Character Display */
  45 #define FTDI_XF_640_PID 0xFC0E  /* 640: Two line Display */
  46 #define FTDI_XF_642_PID 0xFC0F  /* 642: Two line Display */
  47
  48 /* Video Networks Limited / Homechoice in the UK use an ftdi-based device for their 1Mb */
  49 /* broadband internet service.  The following PID is exhibited by the usb device supplied */
  50 /* (the VID is the standard ftdi vid (FTDI_VID) */
  51 #define FTDI_VNHCPCUSB_D_PID 0xfe38 /* Product Id */
  52
  53 /*
  54  * The following are the values for the Matrix Orbital LCD displays,
  55  * which are the FT232BM ( similar to the 8U232AM )
  56  */
  57 #define FTDI_MTXORB_0_PID      0xFA00  /* Matrix Orbital Product Id */
  58 #define FTDI_MTXORB_1_PID      0xFA01  /* Matrix Orbital Product Id */
  59 #define FTDI_MTXORB_2_PID      0xFA02  /* Matrix Orbital Product Id */
  60 #define FTDI_MTXORB_3_PID      0xFA03  /* Matrix Orbital Product Id */
  61 #define FTDI_MTXORB_4_PID      0xFA04  /* Matrix Orbital Product Id */
  62 #define FTDI_MTXORB_5_PID      0xFA05  /* Matrix Orbital Product Id */
  63 #define FTDI_MTXORB_6_PID      0xFA06  /* Matrix Orbital Product Id */
  64
  65 /* Interbiometrics USB I/O Board */
  66 /* Developed for Interbiometrics by Rudolf Gugler */
  67 #define INTERBIOMETRICS_VID              0x1209
  68 #define INTERBIOMETRICS_IOBOARD_PID      0x1002
  69 #define INTERBIOMETRICS_MINI_IOBOARD_PID 0x1006
  70
  71 /*
  72  * The following are the values for the Perle Systems
  73  * UltraPort USB serial converters
  74  */
  75 #define FTDI_PERLE_ULTRAPORT_PID 0xF0C0 /* Perle UltraPort Product Id */
  76
  77 /*
  78  * The following are the values for the Sealevel SeaLINK+ adapters.
  79  * (Original list sent by Tuan Hoang.  Ian Abbott renamed the macros and
  80  * removed some PIDs that don't seem to match any existing products.)
  81  */
  82 #define SEALEVEL_VID            0x0c52  /* Sealevel Vendor ID */
  83 #define SEALEVEL_2101_PID       0x2101  /* SeaLINK+232 (2101/2105) */
  84 #define SEALEVEL_2102_PID       0x2102  /* SeaLINK+485 (2102) */
  85 #define SEALEVEL_2103_PID       0x2103  /* SeaLINK+232I (2103) */
  86 #define SEALEVEL_2104_PID       0x2104  /* SeaLINK+485I (2104) */
  87 #define SEALEVEL_2201_1_PID     0x2211  /* SeaPORT+2/232 (2201) Port 1 */
  88 #define SEALEVEL_2201_2_PID     0x2221  /* SeaPORT+2/232 (2201) Port 2 */
  89 #define SEALEVEL_2202_1_PID     0x2212  /* SeaPORT+2/485 (2202) Port 1 */
  90 #define SEALEVEL_2202_2_PID     0x2222  /* SeaPORT+2/485 (2202) Port 2 */
  91 #define SEALEVEL_2203_1_PID     0x2213  /* SeaPORT+2 (2203) Port 1 */
  92 #define SEALEVEL_2203_2_PID     0x2223  /* SeaPORT+2 (2203) Port 2 */
  93 #define SEALEVEL_2401_1_PID     0x2411  /* SeaPORT+4/232 (2401) Port 1 */
  94 #define SEALEVEL_2401_2_PID     0x2421  /* SeaPORT+4/232 (2401) Port 2 */
  95 #define SEALEVEL_2401_3_PID     0x2431  /* SeaPORT+4/232 (2401) Port 3 */
  96 #define SEALEVEL_2401_4_PID     0x2441  /* SeaPORT+4/232 (2401) Port 4 */
  97 #define SEALEVEL_2402_1_PID     0x2412  /* SeaPORT+4/485 (2402) Port 1 */
  98 #define SEALEVEL_2402_2_PID     0x2422  /* SeaPORT+4/485 (2402) Port 2 */
  99 #define SEALEVEL_2402_3_PID     0x2432  /* SeaPORT+4/485 (2402) Port 3 */
 100 #define SEALEVEL_2402_4_PID     0x2442  /* SeaPORT+4/485 (2402) Port 4 */
 101 #define SEALEVEL_2403_1_PID     0x2413  /* SeaPORT+4 (2403) Port 1 */
 102 #define SEALEVEL_2403_2_PID     0x2423  /* SeaPORT+4 (2403) Port 2 */
 103 #define SEALEVEL_2403_3_PID     0x2433  /* SeaPORT+4 (2403) Port 3 */
 104 #define SEALEVEL_2403_4_PID     0x2443  /* SeaPORT+4 (2403) Port 4 */
 105 #define SEALEVEL_2801_1_PID     0X2811  /* SeaLINK+8/232 (2801) Port 1 */
 106 #define SEALEVEL_2801_2_PID     0X2821  /* SeaLINK+8/232 (2801) Port 2 */
 107 #define SEALEVEL_2801_3_PID     0X2831  /* SeaLINK+8/232 (2801) Port 3 */
 108 #define SEALEVEL_2801_4_PID     0X2841  /* SeaLINK+8/232 (2801) Port 4 */
 109 #define SEALEVEL_2801_5_PID     0X2851  /* SeaLINK+8/232 (2801) Port 5 */
 110 #define SEALEVEL_2801_6_PID     0X2861  /* SeaLINK+8/232 (2801) Port 6 */
 111 #define SEALEVEL_2801_7_PID     0X2871  /* SeaLINK+8/232 (2801) Port 7 */
 112 #define SEALEVEL_2801_8_PID     0X2881  /* SeaLINK+8/232 (2801) Port 8 */
 113 #define SEALEVEL_2802_1_PID     0X2812  /* SeaLINK+8/485 (2802) Port 1 */
 114 #define SEALEVEL_2802_2_PID     0X2822  /* SeaLINK+8/485 (2802) Port 2 */
 115 #define SEALEVEL_2802_3_PID     0X2832  /* SeaLINK+8/485 (2802) Port 3 */
 116 #define SEALEVEL_2802_4_PID     0X2842  /* SeaLINK+8/485 (2802) Port 4 */
 117 #define SEALEVEL_2802_5_PID     0X2852  /* SeaLINK+8/485 (2802) Port 5 */
 118 #define SEALEVEL_2802_6_PID     0X2862  /* SeaLINK+8/485 (2802) Port 6 */
 119 #define SEALEVEL_2802_7_PID     0X2872  /* SeaLINK+8/485 (2802) Port 7 */
 120 #define SEALEVEL_2802_8_PID     0X2882  /* SeaLINK+8/485 (2802) Port 8 */
 121 #define SEALEVEL_2803_1_PID     0X2813  /* SeaLINK+8 (2803) Port 1 */
 122 #define SEALEVEL_2803_2_PID     0X2823  /* SeaLINK+8 (2803) Port 2 */
 123 #define SEALEVEL_2803_3_PID     0X2833  /* SeaLINK+8 (2803) Port 3 */
 124 #define SEALEVEL_2803_4_PID     0X2843  /* SeaLINK+8 (2803) Port 4 */
 125 #define SEALEVEL_2803_5_PID     0X2853  /* SeaLINK+8 (2803) Port 5 */
 126 #define SEALEVEL_2803_6_PID     0X2863  /* SeaLINK+8 (2803) Port 6 */
 127 #define SEALEVEL_2803_7_PID     0X2873  /* SeaLINK+8 (2803) Port 7 */
 128 #define SEALEVEL_2803_8_PID     0X2883  /* SeaLINK+8 (2803) Port 8 */
 129
 130 /*
 131  * DSS-20 Sync Station for Sony Ericsson P800
 132  */
 133
 134 #define FTDI_DSS20_PID          0xFC82
 135
 136 /*
 137  * Home Electronics (www.home-electro.com) USB gadgets
 138  */
 139 #define FTDI_HE_TIRA1_PID       0xFA78  /* Tira-1 IR tranceiver */
 140
 141 /* USB-UIRT - An infrared receiver and transmitter using the 8U232AM chip */
 142 /* http://home.earthlink.net/~jrhees/USBUIRT/index.htm */
 143 #define FTDI_USB_UIRT_PID       0xF850  /* Product Id */
 144
 145 /* ELV USB Module UO100 (PID sent by Stefan Frings) */
 146 #define FTDI_ELV_UO100_PID      0xFB58  /* Product Id */
 147
 148 /*
 149  * Definitions for ID TECH (www.idt-net.com) devices
 150  */
 151 #define IDTECH_VID              0x0ACD  /* ID TECH Vendor ID */
 152 #define IDTECH_IDT1221U_PID     0x0300  /* IDT1221U USB to RS-232 adapter */
 153
 154 /*
 155  * Definitions for Omnidirectional Control Technology, Inc. devices
 156  */
 157 #define OCT_VID                 0x0B39  /* OCT vendor ID */
 158 /* Note: OCT US101 is also rebadged as Dick Smith Electronics (NZ) XH6381 */
 159 /* Also rebadged as Dick Smith Electronics (Aus) XH6451 */
 160 /* Also rebadged as SIIG Inc. model US2308 hardware version 1 */
 161 #define OCT_US101_PID           0x0421  /* OCT US101 USB to RS-232 */
 162
 163 /* an infrared receiver for user access control with IR tags */
 164 #define FTDI_PIEGROUP_PID       0xF208  /* Product Id */
 165
 166 /*
 167  * Protego product ids
 168  */
 169 #define PROTEGO_SPECIAL_1       0xFC70  /* special/unknown device */
 170 #define PROTEGO_R2X0            0xFC71  /* R200-USB TRNG unit (R210, R220, and R230) */
 171 #define PROTEGO_SPECIAL_3       0xFC72  /* special/unknown device */
 172 #define PROTEGO_SPECIAL_4       0xFC73  /* special/unknown device */
 173
 174 /*
 175  * Gude Analog- und Digitalsysteme GmbH
 176  */
 177 #define FTDI_GUDEADS_E808_PID    0xE808
 178 #define FTDI_GUDEADS_E809_PID    0xE809
 179 #define FTDI_GUDEADS_E80A_PID    0xE80A
 180 #define FTDI_GUDEADS_E80B_PID    0xE80B
 181 #define FTDI_GUDEADS_E80C_PID    0xE80C
 182 #define FTDI_GUDEADS_E80D_PID    0xE80D
 183 #define FTDI_GUDEADS_E80E_PID    0xE80E
 184 #define FTDI_GUDEADS_E80F_PID    0xE80F
 185 #define FTDI_GUDEADS_E888_PID    0xE888  /* Expert ISDN Control USB */
 186 #define FTDI_GUDEADS_E889_PID    0xE889  /* USB RS-232 OptoBridge */
 187 #define FTDI_GUDEADS_E88A_PID    0xE88A
 188 #define FTDI_GUDEADS_E88B_PID    0xE88B
 189 #define FTDI_GUDEADS_E88C_PID    0xE88C
 190 #define FTDI_GUDEADS_E88D_PID    0xE88D
 191 #define FTDI_GUDEADS_E88E_PID    0xE88E
 192 #define FTDI_GUDEADS_E88F_PID    0xE88F
 193
 194 /*
 195  * Linx Technologies product ids
 196  */
 197 #define LINX_SDMUSBQSS_PID      0xF448  /* Linx SDM-USB-QS-S */
 198 #define LINX_MASTERDEVEL2_PID   0xF449   /* Linx Master Development 2.0 */
 199 #define LINX_FUTURE_0_PID   0xF44A   /* Linx future device */
 200 #define LINX_FUTURE_1_PID   0xF44B   /* Linx future device */
 201 #define LINX_FUTURE_2_PID   0xF44C   /* Linx future device */
 202
 203 /* CCS Inc. ICDU/ICDU40 product ID - the FT232BM is used in an in-circuit-debugger */
 204 /* unit for PIC16's/PIC18's */
 205 #define FTDI_CCSICDU20_0_PID    0xF9D0
 206 #define FTDI_CCSICDU40_1_PID    0xF9D1
 207
 208 /* Inside Accesso contactless reader (http://www.insidefr.com) */
 209 #define INSIDE_ACCESSO          0xFAD0
 210
 211 /*
 212  * Intrepid Control Systems (http://www.intrepidcs.com/) ValueCAN and NeoVI
 213  */
 214 #define INTREPID_VID            0x093C
 215 #define INTREPID_VALUECAN_PID   0x0601
 216 #define INTREPID_NEOVI_PID      0x0701
 217
 218 /*
 219  * Falcom Wireless Communications GmbH
 220  */
 221 #define FALCOM_VID              0x0F94  /* Vendor Id */
 222 #define FALCOM_TWIST_PID        0x0001  /* Falcom Twist USB GPRS modem */
 223
 224 /*
 225  * SUUNTO product ids
 226  */
 227 #define FTDI_SUUNTO_SPORTS_PID  0xF680  /* Suunto Sports instrument */
 228
 229 /*
 230  * Definitions for B&B Electronics products.
 231  */
 232 #define BANDB_VID               0x0856  /* B&B Electronics Vendor ID */
 233 #define BANDB_USOTL4_PID        0xAC01  /* USOTL4 Isolated RS-485 Converter */
 234 #define BANDB_USTL4_PID         0xAC02  /* USTL4 RS-485 Converter */
 235 #define BANDB_USO9ML2_PID       0xAC03  /* USO9ML2 Isolated RS-232 Converter */
 236
 237 /*
 238  * RM Michaelides CANview USB (http://www.rmcan.com)
 239  * CAN fieldbus interface adapter, added by port GmbH www.port.de)
 240  * Ian Abbott changed the macro names for consistency.
 241  */
 242 #define FTDI_RM_CANVIEW_PID     0xfd60  /* Product Id */
 243
 244 /*
 245  * EVER Eco Pro UPS (http://www.ever.com.pl/)
 246  */
 247
 248 #define EVER_ECO_PRO_CDS        0xe520  /* RS-232 converter */
 249
 250 /*
 251  * 4N-GALAXY.DE PIDs for CAN-USB, USB-RS232, USB-RS422, USB-RS485,
 252  * USB-TTY activ, USB-TTY passiv.  Some PIDs are used by several devices
 253  * and I'm not entirely sure which are used by which.
 254  */
 255 #define FTDI_4N_GALAXY_DE_0_PID 0x8372
 256 #define FTDI_4N_GALAXY_DE_1_PID 0xF3C0
 257 #define FTDI_4N_GALAXY_DE_2_PID 0xF3C1
 258
 259 /*
 260  * Mobility Electronics products.
 261  */
 262 #define MOBILITY_VID                    0x1342
 263 #define MOBILITY_USB_SERIAL_PID         0x0202  /* EasiDock USB 200 serial */
 264
 265 /*
 266  * Active Robots product ids.
 267  */
 268 #define FTDI_ACTIVE_ROBOTS_PID  0xE548  /* USB comms board */
 269
 270 /* Commands */
 271 #define FTDI_SIO_RESET          0 /* Reset the port */
 272 #define FTDI_SIO_MODEM_CTRL     1 /* Set the modem control register */
 273 #define FTDI_SIO_SET_FLOW_CTRL  2 /* Set flow control register */
 274 #define FTDI_SIO_SET_BAUD_RATE  3 /* Set baud rate */
 275 #define FTDI_SIO_SET_DATA       4 /* Set the data characteristics of the port */
 276 #define FTDI_SIO_GET_MODEM_STATUS       5 /* Retrieve current value of modern status register */
 277 #define FTDI_SIO_SET_EVENT_CHAR 6 /* Set the event character */
 278 #define FTDI_SIO_SET_ERROR_CHAR 7 /* Set the error character */
 279 #define FTDI_SIO_SET_LATENCY_TIMER      9 /* Set the latency timer */
 280 #define FTDI_SIO_GET_LATENCY_TIMER      10 /* Get the latency timer */
 281
 282
 283 /*
 284  *   BmRequestType:  1100 0000b
 285  *   bRequest:       FTDI_E2_READ
 286  *   wValue:         0
 287  *   wIndex:         Address of word to read
 288  *   wLength:        2
 289  *   Data:           Will return a word of data from E2Address
 290  *
 291  */
 292
 293 /* Port Identifier Table */
 294 #define PIT_DEFAULT             0 /* SIOA */
 295 #define PIT_SIOA                1 /* SIOA */
 296 /* The device this driver is tested with one has only one port */
 297 #define PIT_SIOB                2 /* SIOB */
 298 #define PIT_PARALLEL            3 /* Parallel */
 299
 300 /* FTDI_SIO_RESET */
 301 #define FTDI_SIO_RESET_REQUEST FTDI_SIO_RESET
 302 #define FTDI_SIO_RESET_REQUEST_TYPE 0x40
 303 #define FTDI_SIO_RESET_SIO 0
 304 #define FTDI_SIO_RESET_PURGE_RX 1
 305 #define FTDI_SIO_RESET_PURGE_TX 2
 306
 307 /*
 308  * BmRequestType:  0100 0000B
 309  * bRequest:       FTDI_SIO_RESET
 310  * wValue:         Control Value
 311  *                   0 = Reset SIO
 312  *                   1 = Purge RX buffer
 313  *                   2 = Purge TX buffer
 314  * wIndex:         Port
 315  * wLength:        0
 316  * Data:           None
 317  *
 318  * The Reset SIO command has this effect:
 319  *
 320  *    Sets flow control set to 'none'
 321  *    Event char = $0D
 322  *    Event trigger = disabled
 323  *    Purge RX buffer
 324  *    Purge TX buffer
 325  *    Clear DTR
 326  *    Clear RTS
 327  *    baud and data format not reset
 328  *
 329  * The Purge RX and TX buffer commands affect nothing except the buffers
 330  *
 331    */
 332
 333 /* FTDI_SIO_SET_BAUDRATE */
 334 #define FTDI_SIO_SET_BAUDRATE_REQUEST_TYPE 0x40
 335 #define FTDI_SIO_SET_BAUDRATE_REQUEST 3
 336
 337 /*
 338  * BmRequestType:  0100 0000B
 339  * bRequest:       FTDI_SIO_SET_BAUDRATE
 340  * wValue:         BaudDivisor value - see below
 341  * wIndex:         Port
 342  * wLength:        0
 343  * Data:           None
 344  * The BaudDivisor values are calculated as follows:
 345  * - BaseClock is either 12000000 or 48000000 depending on the device. FIXME: I wish
 346  *   I knew how to detect old chips to select proper base clock!
 347  * - BaudDivisor is a fixed point number encoded in a funny way.
 348  *   (--WRONG WAY OF THINKING--)
 349  *   BaudDivisor is a fixed point number encoded with following bit weighs:
 350  *   (-2)(-1)(13..0). It is a radical with a denominator of 4, so values
 351  *   end with 0.0 (00...), 0.25 (10...), 0.5 (01...), and 0.75 (11...).
 352  *   (--THE REALITY--)
 353  *   The both-bits-set has quite different meaning from 0.75 - the chip designers
 354  *   have decided it to mean 0.125 instead of 0.75.
 355  *   This info looked up in FTDI application note "FT8U232 DEVICES \ Data Rates
 356  *   and Flow Control Consideration for USB to RS232".
 357  * - BaudDivisor = (BaseClock / 16) / BaudRate, where the (=) operation should
 358  *   automagically re-encode the resulting value to take fractions into consideration.
 359  * As all values are integers, some bit twiddling is in order:
 360  *   BaudDivisor = (BaseClock / 16 / BaudRate) |
 361  *   (((BaseClock / 2 / BaudRate) & 4) ? 0x4000    // 0.5
 362  *    : ((BaseClock / 2 / BaudRate) & 2) ? 0x8000  // 0.25
 363  *    : ((BaseClock / 2 / BaudRate) & 1) ? 0xc000  // 0.125
 364  *    : 0)
 365  *
 366  * For the FT232BM, a 17th divisor bit was introduced to encode the multiples
 367  * of 0.125 missing from the FT8U232AM.  Bits 16 to 14 are coded as follows
 368  * (the first four codes are the same as for the FT8U232AM, where bit 16 is
 369  * always 0):
 370  *   000 - add .000 to divisor
 371  *   001 - add .500 to divisor
 372  *   010 - add .250 to divisor
 373  *   011 - add .125 to divisor
 374  *   100 - add .375 to divisor
 375  *   101 - add .625 to divisor
 376  *   110 - add .750 to divisor
 377  *   111 - add .875 to divisor
 378  * Bits 15 to 0 of the 17-bit divisor are placed in the urb value.  Bit 16 is
 379  * placed in bit 0 of the urb index.
 380  *
 381  * Note that there are a couple of special cases to support the highest baud
 382  * rates.  If the calculated divisor value is 1, this needs to be replaced with
 383  * 0.  Additionally for the FT232BM, if the calculated divisor value is 0x4001
 384  * (1.5), this needs to be replaced with 0x0001 (1) (but this divisor value is
 385  * not supported by the FT8U232AM).
 386  */
 387
 388 typedef enum {
 389         SIO = 1,
 390         FT8U232AM = 2,
 391         FT232BM = 3,
 392         FT2232C = 4,
 393 } ftdi_chip_type_t;
 394
 395 typedef enum {
 396  ftdi_sio_b300 = 0,
 397  ftdi_sio_b600 = 1,
 398  ftdi_sio_b1200 = 2,
 399  ftdi_sio_b2400 = 3,
 400  ftdi_sio_b4800 = 4,
 401  ftdi_sio_b9600 = 5,
 402  ftdi_sio_b19200 = 6,
 403  ftdi_sio_b38400 = 7,
 404  ftdi_sio_b57600 = 8,
 405  ftdi_sio_b115200 = 9
 406 } FTDI_SIO_baudrate_t ;
 407
 408 /*
 409  * The ftdi_8U232AM_xxMHz_byyy constants have been removed. The encoded divisor values
 410  * are calculated internally.
 411  */
 412
 413 #define FTDI_SIO_SET_DATA_REQUEST FTDI_SIO_SET_DATA
 414 #define FTDI_SIO_SET_DATA_REQUEST_TYPE 0x40
 415 #define FTDI_SIO_SET_DATA_PARITY_NONE (0x0 << 8 )
 416 #define FTDI_SIO_SET_DATA_PARITY_ODD (0x1 << 8 )
 417 #define FTDI_SIO_SET_DATA_PARITY_EVEN (0x2 << 8 )
 418 #define FTDI_SIO_SET_DATA_PARITY_MARK (0x3 << 8 )
 419 #define FTDI_SIO_SET_DATA_PARITY_SPACE (0x4 << 8 )
 420 #define FTDI_SIO_SET_DATA_STOP_BITS_1 (0x0 << 11 )
 421 #define FTDI_SIO_SET_DATA_STOP_BITS_15 (0x1 << 11 )
 422 #define FTDI_SIO_SET_DATA_STOP_BITS_2 (0x2 << 11 )
 423 #define FTDI_SIO_SET_BREAK (0x1 << 14)
 424 /* FTDI_SIO_SET_DATA */
 425
 426 /*
 427  * BmRequestType:  0100 0000B
 428  * bRequest:       FTDI_SIO_SET_DATA
 429  * wValue:         Data characteristics (see below)
 430  * wIndex:         Port
 431  * wLength:        0
 432  * Data:           No
 433  *
 434  * Data characteristics
 435  *
 436  *   B0..7   Number of data bits
 437  *   B8..10  Parity
 438  *           0 = None
 439  *           1 = Odd
 440  *           2 = Even
 441  *           3 = Mark
 442  *           4 = Space
 443  *   B11..13 Stop Bits
 444  *           0 = 1
 445  *           1 = 1.5
 446  *           2 = 2
 447  *   B14
 448  *           1 = TX ON (break)
 449  *           0 = TX OFF (normal state)
 450  *   B15 Reserved
 451  *
 452  */
 453
 454
 455
 456 /* FTDI_SIO_MODEM_CTRL */
 457 #define FTDI_SIO_SET_MODEM_CTRL_REQUEST_TYPE 0x40
 458 #define FTDI_SIO_SET_MODEM_CTRL_REQUEST FTDI_SIO_MODEM_CTRL
 459
 460 /*
 461  * BmRequestType:   0100 0000B
 462  * bRequest:        FTDI_SIO_MODEM_CTRL
 463  * wValue:          ControlValue (see below)
 464  * wIndex:          Port
 465  * wLength:         0
 466  * Data:            None
 467  *
 468  * NOTE: If the device is in RTS/CTS flow control, the RTS set by this
 469  * command will be IGNORED without an error being returned
 470  * Also - you can not set DTR and RTS with one control message
 471  */
 472
 473 #define FTDI_SIO_SET_DTR_MASK 0x1
 474 #define FTDI_SIO_SET_DTR_HIGH ( 1 | ( FTDI_SIO_SET_DTR_MASK  << 8))
 475 #define FTDI_SIO_SET_DTR_LOW  ( 0 | ( FTDI_SIO_SET_DTR_MASK  << 8))
 476 #define FTDI_SIO_SET_RTS_MASK 0x2
 477 #define FTDI_SIO_SET_RTS_HIGH ( 2 | ( FTDI_SIO_SET_RTS_MASK << 8 ))
 478 #define FTDI_SIO_SET_RTS_LOW ( 0 | ( FTDI_SIO_SET_RTS_MASK << 8 ))
 479
 480 /*
 481  * ControlValue
 482  * B0    DTR state
 483  *          0 = reset
 484  *          1 = set
 485  * B1    RTS state
 486  *          0 = reset
 487  *          1 = set
 488  * B2..7 Reserved
 489  * B8    DTR state enable
 490  *          0 = ignore
 491  *          1 = use DTR state
 492  * B9    RTS state enable
 493  *          0 = ignore
 494  *          1 = use RTS state
 495  * B10..15 Reserved
 496  */
 497
 498 /* FTDI_SIO_SET_FLOW_CTRL */
 499 #define FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE 0x40
 500 #define FTDI_SIO_SET_FLOW_CTRL_REQUEST FTDI_SIO_SET_FLOW_CTRL
 501 #define FTDI_SIO_DISABLE_FLOW_CTRL 0x0
 502 #define FTDI_SIO_RTS_CTS_HS (0x1 << 8)
 503 #define FTDI_SIO_DTR_DSR_HS (0x2 << 8)
 504 #define FTDI_SIO_XON_XOFF_HS (0x4 << 8)
 505 /*
 506  *   BmRequestType:  0100 0000b
 507  *   bRequest:       FTDI_SIO_SET_FLOW_CTRL
 508  *   wValue:         Xoff/Xon
 509  *   wIndex:         Protocol/Port - hIndex is protocl / lIndex is port
 510  *   wLength:        0
 511  *   Data:           None
 512  *
 513  * hIndex protocol is:
 514  *   B0 Output handshaking using RTS/CTS
 515  *       0 = disabled
 516  *       1 = enabled
 517  *   B1 Output handshaking using DTR/DSR
 518  *       0 = disabled
 519  *       1 = enabled
 520  *   B2 Xon/Xoff handshaking
 521  *       0 = disabled
 522  *       1 = enabled
 523  *
 524  * A value of zero in the hIndex field disables handshaking
 525  *
 526  * If Xon/Xoff handshaking is specified, the hValue field should contain the XOFF character
 527  * and the lValue field contains the XON character.
 528  */
 529
 530 /*
 531  * FTDI_SIO_GET_LATENCY_TIMER
 532  *
 533  * Set the timeout interval. The FTDI collects data from the slave
 534  * device, transmitting it to the host when either A) 62 bytes are
 535  * received, or B) the timeout interval has elapsed and the buffer
 536  * contains at least 1 byte.  Setting this value to a small number
 537  * can dramatically improve performance for applications which send
 538  * small packets, since the default value is 16ms.
 539  */
 540 #define  FTDI_SIO_GET_LATENCY_TIMER_REQUEST FTDI_SIO_GET_LATENCY_TIMER
 541 #define  FTDI_SIO_GET_LATENCY_TIMER_REQUEST_TYPE 0xC0
 542
 543 /*
 544  *  BmRequestType:   1100 0000b
 545  *  bRequest:        FTDI_SIO_GET_LATENCY_TIMER
 546  *  wValue:          0
 547  *  wIndex:          Port
 548  *  wLength:         0
 549  *  Data:            latency (on return)
 550  */
 551
 552 /*
 553  * FTDI_SIO_SET_LATENCY_TIMER
 554  *
 555  * Set the timeout interval. The FTDI collects data from the slave
 556  * device, transmitting it to the host when either A) 62 bytes are
 557  * received, or B) the timeout interval has elapsed and the buffer
 558  * contains at least 1 byte.  Setting this value to a small number
 559  * can dramatically improve performance for applications which send
 560  * small packets, since the default value is 16ms.
 561  */
 562 #define  FTDI_SIO_SET_LATENCY_TIMER_REQUEST FTDI_SIO_SET_LATENCY_TIMER
 563 #define  FTDI_SIO_SET_LATENCY_TIMER_REQUEST_TYPE 0x40
 564
 565 /*
 566  *  BmRequestType:   0100 0000b
 567  *  bRequest:        FTDI_SIO_SET_LATENCY_TIMER
 568  *  wValue:          Latency (milliseconds)
 569  *  wIndex:          Port
 570  *  wLength:         0
 571  *  Data:            None
 572  *
 573  * wValue:
 574  *   B0..7   Latency timer
 575  *   B8..15  0
 576  *
 577  */
 578
 579 /*
 580  * FTDI_SIO_SET_EVENT_CHAR
 581  *
 582  * Set the special event character for the specified communications port.
 583  * If the device sees this character it will immediately return the
 584  * data read so far - rather than wait 40ms or until 62 bytes are read
 585  * which is what normally happens.
 586  */
 587
 588
 589 #define  FTDI_SIO_SET_EVENT_CHAR_REQUEST FTDI_SIO_SET_EVENT_CHAR
 590 #define  FTDI_SIO_SET_EVENT_CHAR_REQUEST_TYPE 0x40
 591
 592
 593 /*
 594  *  BmRequestType:   0100 0000b
 595  *  bRequest:        FTDI_SIO_SET_EVENT_CHAR
 596  *  wValue:          EventChar
 597  *  wIndex:          Port
 598  *  wLength:         0
 599  *  Data:            None
 600  *
 601  * wValue:
 602  *   B0..7   Event Character
 603  *   B8      Event Character Processing
 604  *             0 = disabled
 605  *             1 = enabled
 606  *   B9..15  Reserved
 607  *
 608  */
 609
 610 /* FTDI_SIO_SET_ERROR_CHAR */
 611
 612 /* Set the parity error replacement character for the specified communications port */
 613
 614 /*
 615  *  BmRequestType:  0100 0000b
 616  *  bRequest:       FTDI_SIO_SET_EVENT_CHAR
 617  *  wValue:         Error Char
 618  *  wIndex:         Port
 619  *  wLength:        0
 620  *  Data:           None
 621  *
 622  *Error Char
 623  *  B0..7  Error Character
 624  *  B8     Error Character Processing
 625  *           0 = disabled
 626  *           1 = enabled
 627  *  B9..15 Reserved
 628  *
 629  */
 630
 631 /* FTDI_SIO_GET_MODEM_STATUS */
 632 /* Retreive the current value of the modem status register */
 633
 634 #define FTDI_SIO_GET_MODEM_STATUS_REQUEST_TYPE 0xc0
 635 #define FTDI_SIO_GET_MODEM_STATUS_REQUEST FTDI_SIO_GET_MODEM_STATUS
 636 #define FTDI_SIO_CTS_MASK 0x10
 637 #define FTDI_SIO_DSR_MASK 0x20
 638 #define FTDI_SIO_RI_MASK  0x40
 639 #define FTDI_SIO_RLSD_MASK 0x80
 640 /*
 641  *   BmRequestType:   1100 0000b
 642  *   bRequest:        FTDI_SIO_GET_MODEM_STATUS
 643  *   wValue:          zero
 644  *   wIndex:          Port
 645  *   wLength:         1
 646  *   Data:            Status
 647  *
 648  * One byte of data is returned
 649  * B0..3 0
 650  * B4    CTS
 651  *         0 = inactive
 652  *         1 = active
 653  * B5    DSR
 654  *         0 = inactive
 655  *         1 = active
 656  * B6    Ring Indicator (RI)
 657  *         0 = inactive
 658  *         1 = active
 659  * B7    Receive Line Signal Detect (RLSD)
 660  *         0 = inactive
 661  *         1 = active
 662  */
 663
 664
 665
 666 /* Descriptors returned by the device
 667  *
 668  *  Device Descriptor
 669  *
 670  * Offset       Field           Size    Value   Description
 671  * 0    bLength         1       0x12    Size of descriptor in bytes
 672  * 1    bDescriptorType 1       0x01    DEVICE Descriptor Type
 673  * 2    bcdUSB          2       0x0110  USB Spec Release Number
 674  * 4    bDeviceClass    1       0x00    Class Code
 675  * 5    bDeviceSubClass 1       0x00    SubClass Code
 676  * 6    bDeviceProtocol 1       0x00    Protocol Code
 677  * 7    bMaxPacketSize0 1       0x08    Maximum packet size for endpoint 0
 678  * 8    idVendor        2       0x0403  Vendor ID
 679  * 10   idProduct       2       0x8372  Product ID (FTDI_SIO_PID)
 680  * 12   bcdDevice       2       0x0001  Device release number
 681  * 14   iManufacturer   1       0x01    Index of man. string desc
 682  * 15   iProduct        1       0x02    Index of prod string desc
 683  * 16   iSerialNumber   1       0x02    Index of serial nmr string desc
 684  * 17   bNumConfigurations 1    0x01    Number of possible configurations
 685  *
 686  * Configuration Descriptor
 687  *
 688  * Offset       Field                   Size    Value
 689  * 0    bLength                 1       0x09    Size of descriptor in bytes
 690  * 1    bDescriptorType         1       0x02    CONFIGURATION Descriptor Type
 691  * 2    wTotalLength            2       0x0020  Total length of data
 692  * 4    bNumInterfaces          1       0x01    Number of interfaces supported
 693  * 5    bConfigurationValue     1       0x01    Argument for SetCOnfiguration() req
 694  * 6    iConfiguration          1       0x02    Index of config string descriptor
 695  * 7    bmAttributes            1       0x20    Config characteristics Remote Wakeup
 696  * 8    MaxPower                1       0x1E    Max power consumption
 697  *
 698  * Interface Descriptor
 699  *
 700  * Offset       Field                   Size    Value
 701  * 0    bLength                 1       0x09    Size of descriptor in bytes
 702  * 1    bDescriptorType         1       0x04    INTERFACE Descriptor Type
 703  * 2    bInterfaceNumber        1       0x00    Number of interface
 704  * 3    bAlternateSetting       1       0x00    Value used to select alternate
 705  * 4    bNumEndpoints           1       0x02    Number of endpoints
 706  * 5    bInterfaceClass         1       0xFF    Class Code
 707  * 6    bInterfaceSubClass      1       0xFF    Subclass Code
 708  * 7    bInterfaceProtocol      1       0xFF    Protocol Code
 709  * 8    iInterface              1       0x02    Index of interface string description
 710  *
 711  * IN Endpoint Descriptor
 712  *
 713  * Offset       Field                   Size    Value
 714  * 0    bLength                 1       0x07    Size of descriptor in bytes
 715  * 1    bDescriptorType         1       0x05    ENDPOINT descriptor type
 716  * 2    bEndpointAddress        1       0x82    Address of endpoint
 717  * 3    bmAttributes            1       0x02    Endpoint attributes - Bulk
 718  * 4    bNumEndpoints           2       0x0040  maximum packet size
 719  * 5    bInterval               1       0x00    Interval for polling endpoint
 720  *
 721  * OUT Endpoint Descriptor
 722  *
 723  * Offset       Field                   Size    Value
 724  * 0    bLength                 1       0x07    Size of descriptor in bytes
 725  * 1    bDescriptorType         1       0x05    ENDPOINT descriptor type
 726  * 2    bEndpointAddress        1       0x02    Address of endpoint
 727  * 3    bmAttributes            1       0x02    Endpoint attributes - Bulk
 728  * 4    bNumEndpoints           2       0x0040  maximum packet size
 729  * 5    bInterval               1       0x00    Interval for polling endpoint
 730  *
 731  * DATA FORMAT
 732  *
 733  * IN Endpoint
 734  *
 735  * The device reserves the first two bytes of data on this endpoint to contain the current
 736  * values of the modem and line status registers. In the absence of data, the device
 737  * generates a message consisting of these two status bytes every 40 ms
 738  *
 739  * Byte 0: Modem Status
 740  *
 741  * Offset       Description
 742  * B0   Reserved - must be 1
 743  * B1   Reserved - must be 0
 744  * B2   Reserved - must be 0
 745  * B3   Reserved - must be 0
 746  * B4   Clear to Send (CTS)
 747  * B5   Data Set Ready (DSR)
 748  * B6   Ring Indicator (RI)
 749  * B7   Receive Line Signal Detect (RLSD)
 750  *
 751  * Byte 1: Line Status
 752  *
 753  * Offset       Description
 754  * B0   Data Ready (DR)
 755  * B1   Overrun Error (OE)
 756  * B2   Parity Error (PE)
 757  * B3   Framing Error (FE)
 758  * B4   Break Interrupt (BI)
 759  * B5   Transmitter Holding Register (THRE)
 760  * B6   Transmitter Empty (TEMT)
 761  * B7   Error in RCVR FIFO
 762  *
 763  */
 764 #define FTDI_RS0_CTS    (1 << 4)
 765 #define FTDI_RS0_DSR    (1 << 5)
 766 #define FTDI_RS0_RI     (1 << 6)
 767 #define FTDI_RS0_RLSD   (1 << 7)
 768
 769 #define FTDI_RS_DR  1
 770 #define FTDI_RS_OE (1<<1)
 771 #define FTDI_RS_PE (1<<2)
 772 #define FTDI_RS_FE (1<<3)
 773 #define FTDI_RS_BI (1<<4)
 774 #define FTDI_RS_THRE (1<<5)
 775 #define FTDI_RS_TEMT (1<<6)
 776 #define FTDI_RS_FIFO  (1<<7)
 777
 778 /*
 779  * OUT Endpoint
 780  *
 781  * This device reserves the first bytes of data on this endpoint contain the length
 782  * and port identifier of the message. For the FTDI USB Serial converter the port
 783  * identifier is always 1.
 784  *
 785  * Byte 0: Line Status
 786  *
 787  * Offset       Description
 788  * B0   Reserved - must be 1
 789  * B1   Reserved - must be 0
 790  * B2..7        Length of message - (not including Byte 0)
 791  *
 792  */
 793