drivers/video/Kconfig

   1 #
   2 # Video configuration
   3 #
   4
   5 menu "Graphics support"
   6         depends on HAS_IOMEM
   7
   8 config HAVE_FB_ATMEL
   9         bool
  10
  11 config HAVE_FB_IMX
  12         bool
  13
  14 source "drivers/char/agp/Kconfig"
  15
  16 source "drivers/gpu/vga/Kconfig"
  17
  18 source "drivers/gpu/drm/Kconfig"
  19
  20 config VGASTATE
  21        tristate
  22        default n
  23
  24 config VIDEO_OUTPUT_CONTROL
  25         tristate "Lowlevel video output switch controls"
  26         help
  27           This framework adds support for low-level control of the video
  28           output switch.
  29
  30 menuconfig FB
  31         tristate "Support for frame buffer devices"
  32         ---help---
  33           The frame buffer device provides an abstraction for the graphics
  34           hardware. It represents the frame buffer of some video hardware and
  35           allows application software to access the graphics hardware through
  36           a well-defined interface, so the software doesn't need to know
  37           anything about the low-level (hardware register) stuff.
  38
  39           Frame buffer devices work identically across the different
  40           architectures supported by Linux and make the implementation of
  41           application programs easier and more portable; at this point, an X
  42           server exists which uses the frame buffer device exclusively.
  43           On several non-X86 architectures, the frame buffer device is the
  44           only way to use the graphics hardware.
  45
  46           The device is accessed through special device nodes, usually located
  47           in the /dev directory, i.e. /dev/fb*.
  48
  49           You need an utility program called fbset to make full use of frame
  50           buffer devices. Please read <file:Documentation/fb/framebuffer.txt>
  51           and the Framebuffer-HOWTO at
  52           <http://www.munted.org.uk/programming/Framebuffer-HOWTO-1.2.html> for more
  53           information.
  54
  55           Say Y here and to the driver for your graphics board below if you
  56           are compiling a kernel for a non-x86 architecture.
  57
  58           If you are compiling for the x86 architecture, you can say Y if you
  59           want to play with it, but it is not essential. Please note that
  60           running graphical applications that directly touch the hardware
  61           (e.g. an accelerated X server) and that are not frame buffer
  62           device-aware may cause unexpected results. If unsure, say N.
  63
  64 config FIRMWARE_EDID
  65        bool "Enable firmware EDID"
  66        depends on FB
  67        default n
  68        ---help---
  69          This enables access to the EDID transferred from the firmware.
  70          On the i386, this is from the Video BIOS. Enable this if DDC/I2C
  71          transfers do not work for your driver and if you are using
  72          nvidiafb, i810fb or savagefb.
  73
  74          In general, choosing Y for this option is safe.  If you
  75          experience extremely long delays while booting before you get
  76          something on your display, try setting this to N.  Matrox cards in
  77          combination with certain motherboards and monitors are known to
  78          suffer from this problem.
  79
  80 config FB_DDC
  81        tristate
  82        depends on FB
  83        select I2C_ALGOBIT
  84        select I2C
  85        default n
  86
  87 config FB_BOOT_VESA_SUPPORT
  88         bool
  89         depends on FB
  90         default n
  91         ---help---
  92           If true, at least one selected framebuffer driver can take advantage
  93           of VESA video modes set at an early boot stage via the vga= parameter.
  94
  95 config FB_CFB_FILLRECT
  96         tristate
  97         depends on FB
  98         default n
  99         ---help---
 100           Include the cfb_fillrect function for generic software rectangle
 101           filling. This is used by drivers that don't provide their own
 102           (accelerated) version.
 103
 104 config FB_CFB_COPYAREA
 105         tristate
 106         depends on FB
 107         default n
 108         ---help---
 109           Include the cfb_copyarea function for generic software area copying.
 110           This is used by drivers that don't provide their own (accelerated)
 111           version.
 112
 113 config FB_CFB_IMAGEBLIT
 114         tristate
 115         depends on FB
 116         default n
 117         ---help---
 118           Include the cfb_imageblit function for generic software image
 119           blitting. This is used by drivers that don't provide their own
 120           (accelerated) version.
 121
 122 config FB_CFB_REV_PIXELS_IN_BYTE
 123         bool
 124         depends on FB
 125         default n
 126         ---help---
 127           Allow generic frame-buffer functions to work on displays with 1, 2
 128           and 4 bits per pixel depths which has opposite order of pixels in
 129           byte order to bytes in long order.
 130
 131 config FB_SYS_FILLRECT
 132         tristate
 133         depends on FB
 134         default n
 135         ---help---
 136           Include the sys_fillrect function for generic software rectangle
 137           filling. This is used by drivers that don't provide their own
 138           (accelerated) version and the framebuffer is in system RAM.
 139
 140 config FB_SYS_COPYAREA
 141         tristate
 142         depends on FB
 143         default n
 144         ---help---
 145           Include the sys_copyarea function for generic software area copying.
 146           This is used by drivers that don't provide their own (accelerated)
 147           version and the framebuffer is in system RAM.
 148
 149 config FB_SYS_IMAGEBLIT
 150         tristate
 151         depends on FB
 152         default n
 153         ---help---
 154           Include the sys_imageblit function for generic software image
 155           blitting. This is used by drivers that don't provide their own
 156           (accelerated) version and the framebuffer is in system RAM.
 157
 158 menuconfig FB_FOREIGN_ENDIAN
 159         bool "Framebuffer foreign endianness support"
 160         depends on FB
 161         ---help---
 162           This menu will let you enable support for the framebuffers with
 163           non-native endianness (e.g. Little-Endian framebuffer on a
 164           Big-Endian machine). Most probably you don't have such hardware,
 165           so it's safe to say "n" here.
 166
 167 choice
 168         prompt "Choice endianness support"
 169         depends on FB_FOREIGN_ENDIAN
 170
 171 config FB_BOTH_ENDIAN
 172         bool "Support for Big- and Little-Endian framebuffers"
 173
 174 config FB_BIG_ENDIAN
 175         bool "Support for Big-Endian framebuffers only"
 176
 177 config FB_LITTLE_ENDIAN
 178         bool "Support for Little-Endian framebuffers only"
 179
 180 endchoice
 181
 182 config FB_SYS_FOPS
 183        tristate
 184        depends on FB
 185        default n
 186
 187 config FB_DEFERRED_IO
 188         bool
 189         depends on FB
 190
 191 config FB_HECUBA
 192         tristate
 193         depends on FB
 194         depends on FB_DEFERRED_IO
 195
 196 config FB_SVGALIB
 197         tristate
 198         depends on FB
 199         default n
 200         ---help---
 201           Common utility functions useful to fbdev drivers of VGA-based
 202           cards.
 203
 204 config FB_MACMODES
 205        tristate
 206        depends on FB
 207        default n
 208
 209 config FB_BACKLIGHT
 210         bool
 211         depends on FB
 212         select BACKLIGHT_LCD_SUPPORT
 213         select BACKLIGHT_CLASS_DEVICE
 214         default n
 215
 216 config FB_MODE_HELPERS
 217         bool "Enable Video Mode Handling Helpers"
 218         depends on FB
 219         default n
 220         ---help---
 221           This enables functions for handling video modes using the
 222           Generalized Timing Formula and the EDID parser. A few drivers rely
 223           on this feature such as the radeonfb, rivafb, and the i810fb. If
 224           your driver does not take advantage of this feature, choosing Y will
 225           just increase the kernel size by about 5K.
 226
 227 config FB_TILEBLITTING
 228        bool "Enable Tile Blitting Support"
 229        depends on FB
 230        default n
 231        ---help---
 232          This enables tile blitting.  Tile blitting is a drawing technique
 233          where the screen is divided into rectangular sections (tiles), whereas
 234          the standard blitting divides the screen into pixels. Because the
 235          default drawing element is a tile, drawing functions will be passed
 236          parameters in terms of number of tiles instead of number of pixels.
 237          For example, to draw a single character, instead of using bitmaps,
 238          an index to an array of bitmaps will be used.  To clear or move a
 239          rectangular section of a screen, the rectangle will be described in
 240          terms of number of tiles in the x- and y-axis.
 241
 242          This is particularly important to one driver, matroxfb.  If
 243          unsure, say N.
 244
 245 comment "Frame buffer hardware drivers"
 246         depends on FB
 247
 248 config FB_CIRRUS
 249         tristate "Cirrus Logic support"
 250         depends on FB && (ZORRO || PCI)
 251         select FB_CFB_FILLRECT
 252         select FB_CFB_COPYAREA
 253         select FB_CFB_IMAGEBLIT
 254         ---help---
 255           This enables support for Cirrus Logic GD542x/543x based boards on
 256           Amiga: SD64, Piccolo, Picasso II/II+, Picasso IV, or EGS Spectrum.
 257
 258           If you have a PCI-based system, this enables support for these
 259           chips: GD-543x, GD-544x, GD-5480.
 260
 261           Please read the file <file:Documentation/fb/cirrusfb.txt>.
 262
 263           Say N unless you have such a graphics board or plan to get one
 264           before you next recompile the kernel.
 265
 266 config FB_PM2
 267         tristate "Permedia2 support"
 268         depends on FB && ((AMIGA && BROKEN) || PCI)
 269         select FB_CFB_FILLRECT
 270         select FB_CFB_COPYAREA
 271         select FB_CFB_IMAGEBLIT
 272         help
 273           This is the frame buffer device driver for cards based on
 274           the 3D Labs Permedia, Permedia 2 and Permedia 2V chips.
 275           The driver was tested on the following cards:
 276                 Diamond FireGL 1000 PRO AGP
 277                 ELSA Gloria Synergy PCI
 278                 Appian Jeronimo PRO (both heads) PCI
 279                 3DLabs Oxygen ACX aka EONtronics Picasso P2 PCI
 280                 Techsource Raptor GFX-8P (aka Sun PGX-32) on SPARC
 281                 ASK Graphic Blaster Exxtreme AGP
 282
 283           To compile this driver as a module, choose M here: the
 284           module will be called pm2fb.
 285
 286 config FB_PM2_FIFO_DISCONNECT
 287         bool "enable FIFO disconnect feature"
 288         depends on FB_PM2 && PCI
 289         help
 290           Support the Permedia2 FIFO disconnect feature.
 291
 292 config FB_ARMCLCD
 293         tristate "ARM PrimeCell PL110 support"
 294         depends on FB && ARM && ARM_AMBA
 295         select FB_CFB_FILLRECT
 296         select FB_CFB_COPYAREA
 297         select FB_CFB_IMAGEBLIT
 298         help
 299           This framebuffer device driver is for the ARM PrimeCell PL110
 300           Colour LCD controller.  ARM PrimeCells provide the building
 301           blocks for System on a Chip devices.
 302
 303           If you want to compile this as a module (=code which can be
 304           inserted into and removed from the running kernel), say M
 305           here and read <file:Documentation/kbuild/modules.txt>.  The module
 306           will be called amba-clcd.
 307
 308 choice
 309
 310         depends on FB_ARMCLCD && (ARCH_LH7A40X || ARCH_LH7952X)
 311         prompt "LCD Panel"
 312         default FB_ARMCLCD_SHARP_LQ035Q7DB02
 313
 314 config FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT
 315         bool "LogicPD LCD 3.5\" QVGA w/HRTFT IC"
 316         help
 317           This is an implementation of the Sharp LQ035Q7DB02, a 3.5"
 318           color QVGA, HRTFT panel.  The LogicPD device includes
 319           an integrated HRTFT controller IC.
 320           The native resolution is 240x320.
 321
 322 config FB_ARMCLCD_SHARP_LQ057Q3DC02
 323         bool "LogicPD LCD 5.7\" QVGA"
 324         help
 325           This is an implementation of the Sharp LQ057Q3DC02, a 5.7"
 326           color QVGA, TFT panel.  The LogicPD device includes an
 327           The native resolution is 320x240.
 328
 329 config FB_ARMCLCD_SHARP_LQ64D343
 330         bool "LogicPD LCD 6.4\" VGA"
 331         help
 332           This is an implementation of the Sharp LQ64D343, a 6.4"
 333           color VGA, TFT panel.  The LogicPD device includes an
 334           The native resolution is 640x480.
 335
 336 config FB_ARMCLCD_SHARP_LQ10D368
 337         bool "LogicPD LCD 10.4\" VGA"
 338         help
 339           This is an implementation of the Sharp LQ10D368, a 10.4"
 340           color VGA, TFT panel.  The LogicPD device includes an
 341           The native resolution is 640x480.
 342
 343
 344 config FB_ARMCLCD_SHARP_LQ121S1DG41
 345         bool "LogicPD LCD 12.1\" SVGA"
 346         help
 347           This is an implementation of the Sharp LQ121S1DG41, a 12.1"
 348           color SVGA, TFT panel.  The LogicPD device includes an
 349           The native resolution is 800x600.
 350
 351           This panel requires a clock rate may be an integer fraction
 352           of the base LCDCLK frequency.  The driver will select the
 353           highest frequency available that is lower than the maximum
 354           allowed.  The panel may flicker if the clock rate is
 355           slower than the recommended minimum.
 356
 357 config FB_ARMCLCD_AUO_A070VW01_WIDE
 358         bool "AU Optronics A070VW01 LCD 7.0\" WIDE"
 359         help
 360           This is an implementation of the AU Optronics, a 7.0"
 361           WIDE Color.  The native resolution is 234x480.
 362
 363 config FB_ARMCLCD_HITACHI
 364         bool "Hitachi Wide Screen 800x480"
 365         help
 366           This is an implementation of the Hitachi 800x480.
 367
 368 endchoice
 369
 370
 371 config FB_ACORN
 372         bool "Acorn VIDC support"
 373         depends on (FB = y) && ARM && ARCH_ACORN
 374         select FB_CFB_FILLRECT
 375         select FB_CFB_COPYAREA
 376         select FB_CFB_IMAGEBLIT
 377         help
 378           This is the frame buffer device driver for the Acorn VIDC graphics
 379           hardware found in Acorn RISC PCs and other ARM-based machines.  If
 380           unsure, say N.
 381
 382 config FB_CLPS711X
 383         bool "CLPS711X LCD support"
 384         depends on (FB = y) && ARM && ARCH_CLPS711X
 385         select FB_CFB_FILLRECT
 386         select FB_CFB_COPYAREA
 387         select FB_CFB_IMAGEBLIT
 388         help
 389           Say Y to enable the Framebuffer driver for the CLPS7111 and
 390           EP7212 processors.
 391
 392 config FB_SA1100
 393         bool "SA-1100 LCD support"
 394         depends on (FB = y) && ARM && ARCH_SA1100
 395         select FB_CFB_FILLRECT
 396         select FB_CFB_COPYAREA
 397         select FB_CFB_IMAGEBLIT
 398         help
 399           This is a framebuffer device for the SA-1100 LCD Controller.
 400           See <http://www.linux-fbdev.org/> for information on framebuffer
 401           devices.
 402
 403           If you plan to use the LCD display with your SA-1100 system, say
 404           Y here.
 405
 406 config FB_IMX
 407         tristate "Motorola i.MX LCD support"
 408         depends on FB && (HAVE_FB_IMX || ARCH_MX1 || ARCH_MX2)
 409         select FB_CFB_FILLRECT
 410         select FB_CFB_COPYAREA
 411         select FB_CFB_IMAGEBLIT
 412
 413 config FB_CYBER2000
 414         tristate "CyberPro 2000/2010/5000 support"
 415         depends on FB && PCI && (BROKEN || !SPARC64)
 416         select FB_CFB_FILLRECT
 417         select FB_CFB_COPYAREA
 418         select FB_CFB_IMAGEBLIT
 419         help
 420           This enables support for the Integraphics CyberPro 20x0 and 5000
 421           VGA chips used in the Rebel.com Netwinder and other machines.
 422           Say Y if you have a NetWinder or a graphics card containing this
 423           device, otherwise say N.
 424
 425 config FB_APOLLO
 426         bool
 427         depends on (FB = y) && APOLLO
 428         default y
 429         select FB_CFB_FILLRECT
 430         select FB_CFB_IMAGEBLIT
 431
 432 config FB_Q40
 433         bool
 434         depends on (FB = y) && Q40
 435         default y
 436         select FB_CFB_FILLRECT
 437         select FB_CFB_COPYAREA
 438         select FB_CFB_IMAGEBLIT
 439
 440 config FB_AMIGA
 441         tristate "Amiga native chipset support"
 442         depends on FB && AMIGA
 443         help
 444           This is the frame buffer device driver for the builtin graphics
 445           chipset found in Amigas.
 446
 447           To compile this driver as a module, choose M here: the
 448           module will be called amifb.
 449
 450 config FB_AMIGA_OCS
 451         bool "Amiga OCS chipset support"
 452         depends on FB_AMIGA
 453         help
 454           This enables support for the original Agnus and Denise video chips,
 455           found in the Amiga 1000 and most A500's and A2000's. If you intend
 456           to run Linux on any of these systems, say Y; otherwise say N.
 457
 458 config FB_AMIGA_ECS
 459         bool "Amiga ECS chipset support"
 460         depends on FB_AMIGA
 461         help
 462           This enables support for the Enhanced Chip Set, found in later
 463           A500's, later A2000's, the A600, the A3000, the A3000T and CDTV. If
 464           you intend to run Linux on any of these systems, say Y; otherwise
 465           say N.
 466
 467 config FB_AMIGA_AGA
 468         bool "Amiga AGA chipset support"
 469         depends on FB_AMIGA
 470         help
 471           This enables support for the Advanced Graphics Architecture (also
 472           known as the AGA or AA) Chip Set, found in the A1200, A4000, A4000T
 473           and CD32. If you intend to run Linux on any of these systems, say Y;
 474           otherwise say N.
 475
 476 config FB_FM2
 477         bool "Amiga FrameMaster II/Rainbow II support"
 478         depends on (FB = y) && ZORRO
 479         select FB_CFB_FILLRECT
 480         select FB_CFB_COPYAREA
 481         select FB_CFB_IMAGEBLIT
 482         help
 483           This is the frame buffer device driver for the Amiga FrameMaster
 484           card from BSC (exhibited 1992 but not shipped as a CBM product).
 485
 486 config FB_ARC
 487         tristate "Arc Monochrome LCD board support"
 488         depends on FB && X86
 489         select FB_SYS_FILLRECT
 490         select FB_SYS_COPYAREA
 491         select FB_SYS_IMAGEBLIT
 492         select FB_SYS_FOPS
 493         help
 494           This enables support for the Arc Monochrome LCD board. The board
 495           is based on the KS-108 lcd controller and is typically a matrix
 496           of 2*n chips. This driver was tested with a 128x64 panel. This
 497           driver supports it for use with x86 SBCs through a 16 bit GPIO
 498           interface (8 bit data, 8 bit control). If you anticipate using
 499           this driver, say Y or M; otherwise say N. You must specify the
 500           GPIO IO address to be used for setting control and data.
 501
 502 config FB_ATARI
 503         bool "Atari native chipset support"
 504         depends on (FB = y) && ATARI
 505         select FB_CFB_FILLRECT
 506         select FB_CFB_COPYAREA
 507         select FB_CFB_IMAGEBLIT
 508         help
 509           This is the frame buffer device driver for the builtin graphics
 510           chipset found in Ataris.
 511
 512 config FB_OF
 513         bool "Open Firmware frame buffer device support"
 514         depends on (FB = y) && (PPC64 || PPC_OF) && (!PPC_PSERIES || PCI)
 515         select FB_CFB_FILLRECT
 516         select FB_CFB_COPYAREA
 517         select FB_CFB_IMAGEBLIT
 518         select FB_MACMODES
 519         help
 520           Say Y if you want support with Open Firmware for your graphics
 521           board.
 522
 523 config FB_CONTROL
 524         bool "Apple \"control\" display support"
 525         depends on (FB = y) && PPC_PMAC && PPC32
 526         select FB_CFB_FILLRECT
 527         select FB_CFB_COPYAREA
 528         select FB_CFB_IMAGEBLIT
 529         select FB_MACMODES
 530         help
 531           This driver supports a frame buffer for the graphics adapter in the
 532           Power Macintosh 7300 and others.
 533
 534 config FB_PLATINUM
 535         bool "Apple \"platinum\" display support"
 536         depends on (FB = y) && PPC_PMAC && PPC32
 537         select FB_CFB_FILLRECT
 538         select FB_CFB_COPYAREA
 539         select FB_CFB_IMAGEBLIT
 540         select FB_MACMODES
 541         help
 542           This driver supports a frame buffer for the "platinum" graphics
 543           adapter in some Power Macintoshes.
 544
 545 config FB_VALKYRIE
 546         bool "Apple \"valkyrie\" display support"
 547         depends on (FB = y) && (MAC || (PPC_PMAC && PPC32))
 548         select FB_CFB_FILLRECT
 549         select FB_CFB_COPYAREA
 550         select FB_CFB_IMAGEBLIT
 551         select FB_MACMODES
 552         help
 553           This driver supports a frame buffer for the "valkyrie" graphics
 554           adapter in some Power Macintoshes.
 555
 556 config FB_CT65550
 557         bool "Chips 65550 display support"
 558         depends on (FB = y) && PPC32 && PCI
 559         select FB_CFB_FILLRECT
 560         select FB_CFB_COPYAREA
 561         select FB_CFB_IMAGEBLIT
 562         help
 563           This is the frame buffer device driver for the Chips & Technologies
 564           65550 graphics chip in PowerBooks.
 565
 566 config FB_ASILIANT
 567         bool "Asiliant (Chips) 69000 display support"
 568         depends on (FB = y) && PCI
 569         select FB_CFB_FILLRECT
 570         select FB_CFB_COPYAREA
 571         select FB_CFB_IMAGEBLIT
 572         help
 573           This is the frame buffer device driver for the Asiliant 69030 chipset
 574
 575 config FB_IMSTT
 576         bool "IMS Twin Turbo display support"
 577         depends on (FB = y) && PCI
 578         select FB_CFB_IMAGEBLIT
 579         select FB_MACMODES if PPC
 580         help
 581           The IMS Twin Turbo is a PCI-based frame buffer card bundled with
 582           many Macintosh and compatible computers.
 583
 584 config FB_VGA16
 585         tristate "VGA 16-color graphics support"
 586         depends on FB && (X86 || PPC)
 587         select FB_CFB_FILLRECT
 588         select FB_CFB_COPYAREA
 589         select FB_CFB_IMAGEBLIT
 590         select VGASTATE
 591         select FONT_8x16 if FRAMEBUFFER_CONSOLE
 592         help
 593           This is the frame buffer device driver for VGA 16 color graphic
 594           cards. Say Y if you have such a card.
 595
 596           To compile this driver as a module, choose M here: the
 597           module will be called vga16fb.
 598
 599 config FB_BF54X_LQ043
 600         tristate "SHARP LQ043 TFT LCD (BF548 EZKIT)"
 601         depends on FB && (BF54x) && !BF542
 602         select FB_CFB_FILLRECT
 603         select FB_CFB_COPYAREA
 604         select FB_CFB_IMAGEBLIT
 605         help
 606          This is the framebuffer device driver for a SHARP LQ043T1DG01 TFT LCD
 607
 608 config FB_BFIN_T350MCQB
 609         tristate "Varitronix COG-T350MCQB TFT LCD display (BF527 EZKIT)"
 610         depends on FB && BLACKFIN
 611         select BFIN_GPTIMERS
 612         select FB_CFB_FILLRECT
 613         select FB_CFB_COPYAREA
 614         select FB_CFB_IMAGEBLIT
 615         help
 616          This is the framebuffer device driver for a Varitronix VL-PS-COG-T350MCQB-01 display TFT LCD
 617          This display is a QVGA 320x240 24-bit RGB display interfaced by an 8-bit wide PPI
 618          It uses PPI[0..7] PPI_FS1, PPI_FS2 and PPI_CLK.
 619
 620 config FB_BFIN_LQ035Q1
 621         tristate "SHARP LQ035Q1DH02 TFT LCD"
 622         depends on FB && BLACKFIN && SPI
 623         select FB_CFB_FILLRECT
 624         select FB_CFB_COPYAREA
 625         select FB_CFB_IMAGEBLIT
 626         select BFIN_GPTIMERS
 627         help
 628           This is the framebuffer device driver for a SHARP LQ035Q1DH02 TFT display found on
 629           the Blackfin Landscape LCD EZ-Extender Card.
 630           This display is a QVGA 320x240 18-bit RGB display interfaced by an 16-bit wide PPI
 631           It uses PPI[0..15] PPI_FS1, PPI_FS2 and PPI_CLK.
 632
 633           To compile this driver as a module, choose M here: the
 634           module will be called bfin-lq035q1-fb.
 635
 636 config FB_STI
 637         tristate "HP STI frame buffer device support"
 638         depends on FB && PARISC
 639         select FB_CFB_FILLRECT
 640         select FB_CFB_COPYAREA
 641         select FB_CFB_IMAGEBLIT
 642         select STI_CONSOLE
 643         select VT
 644         default y
 645         ---help---
 646           STI refers to the HP "Standard Text Interface" which is a set of
 647           BIOS routines contained in a ROM chip in HP PA-RISC based machines.
 648           Enabling this option will implement the linux framebuffer device
 649           using calls to the STI BIOS routines for initialisation.
 650
 651           If you enable this option, you will get a planar framebuffer device
 652           /dev/fb which will work on the most common HP graphic cards of the
 653           NGLE family, including the artist chips (in the 7xx and Bxxx series),
 654           HCRX, HCRX24, CRX, CRX24 and VisEG series.
 655
 656           It is safe to enable this option, so you should probably say "Y".
 657
 658 config FB_MAC
 659         bool "Generic Macintosh display support"
 660         depends on (FB = y) && MAC
 661         select FB_CFB_FILLRECT
 662         select FB_CFB_COPYAREA
 663         select FB_CFB_IMAGEBLIT
 664         select FB_MACMODES
 665
 666 config FB_HP300
 667         bool
 668         depends on (FB = y) && DIO
 669         select FB_CFB_IMAGEBLIT
 670         default y
 671
 672 config FB_TGA
 673         tristate "TGA/SFB+ framebuffer support"
 674         depends on FB && (ALPHA || TC)
 675         select FB_CFB_FILLRECT
 676         select FB_CFB_COPYAREA
 677         select FB_CFB_IMAGEBLIT
 678         select BITREVERSE
 679         ---help---
 680           This is the frame buffer device driver for generic TGA and SFB+
 681           graphic cards.  These include DEC ZLXp-E1, -E2 and -E3 PCI cards,
 682           also known as PBXGA-A, -B and -C, and DEC ZLX-E1, -E2 and -E3
 683           TURBOchannel cards, also known as PMAGD-A, -B and -C.
 684
 685           Due to hardware limitations ZLX-E2 and E3 cards are not supported
 686           for DECstation 5000/200 systems.  Additionally due to firmware
 687           limitations these cards may cause troubles with booting DECstation
 688           5000/240 and /260 systems, but are fully supported under Linux if
 689           you manage to get it going. ;-)
 690
 691           Say Y if you have one of those.
 692
 693 config FB_UVESA
 694         tristate "Userspace VESA VGA graphics support"
 695         depends on FB && CONNECTOR
 696         select FB_CFB_FILLRECT
 697         select FB_CFB_COPYAREA
 698         select FB_CFB_IMAGEBLIT
 699         select FB_MODE_HELPERS
 700         help
 701           This is the frame buffer driver for generic VBE 2.0 compliant
 702           graphic cards. It can also take advantage of VBE 3.0 features,
 703           such as refresh rate adjustment.
 704
 705           This driver generally provides more features than vesafb but
 706           requires a userspace helper application called 'v86d'. See
 707           <file:Documentation/fb/uvesafb.txt> for more information.
 708
 709           If unsure, say N.
 710
 711 config FB_VESA
 712         bool "VESA VGA graphics support"
 713         depends on (FB = y) && X86
 714         select FB_CFB_FILLRECT
 715         select FB_CFB_COPYAREA
 716         select FB_CFB_IMAGEBLIT
 717         select FB_BOOT_VESA_SUPPORT
 718         help
 719           This is the frame buffer device driver for generic VESA 2.0
 720           compliant graphic cards. The older VESA 1.2 cards are not supported.
 721           You will get a boot time penguin logo at no additional cost. Please
 722           read <file:Documentation/fb/vesafb.txt>. If unsure, say Y.
 723
 724 config FB_EFI
 725         bool "EFI-based Framebuffer Support"
 726         depends on (FB = y) && X86 && EFI
 727         select FB_CFB_FILLRECT
 728         select FB_CFB_COPYAREA
 729         select FB_CFB_IMAGEBLIT
 730         help
 731           This is the EFI frame buffer device driver. If the firmware on
 732           your platform is EFI 1.10 or UEFI 2.0, select Y to add support for
 733           using the EFI framebuffer as your console.
 734
 735 config FB_N411
 736        tristate "N411 Apollo/Hecuba devkit support"
 737        depends on FB && X86 && MMU
 738        select FB_SYS_FILLRECT
 739        select FB_SYS_COPYAREA
 740        select FB_SYS_IMAGEBLIT
 741        select FB_SYS_FOPS
 742        select FB_DEFERRED_IO
 743        select FB_HECUBA
 744        help
 745          This enables support for the Apollo display controller in its
 746          Hecuba form using the n411 devkit.
 747
 748 config FB_HGA
 749         tristate "Hercules mono graphics support"
 750         depends on FB && X86
 751         select FB_CFB_FILLRECT
 752         select FB_CFB_COPYAREA
 753         select FB_CFB_IMAGEBLIT
 754         help
 755           Say Y here if you have a Hercules mono graphics card.
 756
 757           To compile this driver as a module, choose M here: the
 758           module will be called hgafb.
 759
 760           As this card technology is 15 years old, most people will answer N
 761           here.
 762
 763 config FB_HGA_ACCEL
 764         bool "Hercules mono Acceleration functions (EXPERIMENTAL)"
 765         depends on FB_HGA && EXPERIMENTAL
 766         ---help---
 767         This will compile the Hercules mono graphics with
 768         acceleration functions.
 769
 770 config FB_SGIVW
 771         tristate "SGI Visual Workstation framebuffer support"
 772         depends on FB && X86_VISWS
 773         select FB_CFB_FILLRECT
 774         select FB_CFB_COPYAREA
 775         select FB_CFB_IMAGEBLIT
 776         help
 777           SGI Visual Workstation support for framebuffer graphics.
 778
 779 config FB_GBE
 780         bool "SGI Graphics Backend frame buffer support"
 781         depends on (FB = y) && (SGI_IP32 || X86_VISWS)
 782         select FB_CFB_FILLRECT
 783         select FB_CFB_COPYAREA
 784         select FB_CFB_IMAGEBLIT
 785         help
 786           This is the frame buffer device driver for SGI Graphics Backend.
 787           This chip is used in SGI O2 and Visual Workstation 320/540.
 788
 789 config FB_GBE_MEM
 790         int "Video memory size in MB"
 791         depends on FB_GBE
 792         default 4
 793         help
 794           This is the amount of memory reserved for the framebuffer,
 795           which can be any value between 1MB and 8MB.
 796
 797 config FB_SBUS
 798         bool "SBUS and UPA framebuffers"
 799         depends on (FB = y) && SPARC
 800         help
 801           Say Y if you want support for SBUS or UPA based frame buffer device.
 802
 803 config FB_BW2
 804         bool "BWtwo support"
 805         depends on (FB = y) && (SPARC && FB_SBUS)
 806         select FB_CFB_FILLRECT
 807         select FB_CFB_COPYAREA
 808         select FB_CFB_IMAGEBLIT
 809         help
 810           This is the frame buffer device driver for the BWtwo frame buffer.
 811
 812 config FB_CG3
 813         bool "CGthree support"
 814         depends on (FB = y) && (SPARC && FB_SBUS)
 815         select FB_CFB_FILLRECT
 816         select FB_CFB_COPYAREA
 817         select FB_CFB_IMAGEBLIT
 818         help
 819           This is the frame buffer device driver for the CGthree frame buffer.
 820
 821 config FB_CG6
 822         bool "CGsix (GX,TurboGX) support"
 823         depends on (FB = y) && (SPARC && FB_SBUS)
 824         select FB_CFB_COPYAREA
 825         select FB_CFB_IMAGEBLIT
 826         help
 827           This is the frame buffer device driver for the CGsix (GX, TurboGX)
 828           frame buffer.
 829
 830 config FB_FFB
 831         bool "Creator/Creator3D/Elite3D support"
 832         depends on FB_SBUS && SPARC64
 833         select FB_CFB_COPYAREA
 834         select FB_CFB_IMAGEBLIT
 835         help
 836           This is the frame buffer device driver for the Creator, Creator3D,
 837           and Elite3D graphics boards.
 838
 839 config FB_TCX
 840         bool "TCX (SS4/SS5 only) support"
 841         depends on FB_SBUS
 842         select FB_CFB_FILLRECT
 843         select FB_CFB_COPYAREA
 844         select FB_CFB_IMAGEBLIT
 845         help
 846           This is the frame buffer device driver for the TCX 24/8bit frame
 847           buffer.
 848
 849 config FB_CG14
 850         bool "CGfourteen (SX) support"
 851         depends on FB_SBUS
 852         select FB_CFB_FILLRECT
 853         select FB_CFB_COPYAREA
 854         select FB_CFB_IMAGEBLIT
 855         help
 856           This is the frame buffer device driver for the CGfourteen frame
 857           buffer on Desktop SPARCsystems with the SX graphics option.
 858
 859 config FB_P9100
 860         bool "P9100 (Sparcbook 3 only) support"
 861         depends on FB_SBUS
 862         select FB_CFB_FILLRECT
 863         select FB_CFB_COPYAREA
 864         select FB_CFB_IMAGEBLIT
 865         help
 866           This is the frame buffer device driver for the P9100 card
 867           supported on Sparcbook 3 machines.
 868
 869 config FB_LEO
 870         bool "Leo (ZX) support"
 871         depends on FB_SBUS
 872         select FB_CFB_FILLRECT
 873         select FB_CFB_COPYAREA
 874         select FB_CFB_IMAGEBLIT
 875         help
 876           This is the frame buffer device driver for the SBUS-based Sun ZX
 877           (leo) frame buffer cards.
 878
 879 config FB_IGA
 880         bool "IGA 168x display support"
 881         depends on (FB = y) && SPARC32
 882         select FB_CFB_FILLRECT
 883         select FB_CFB_COPYAREA
 884         select FB_CFB_IMAGEBLIT
 885         help
 886           This is the framebuffer device for the INTERGRAPHICS 1680 and
 887           successor frame buffer cards.
 888
 889 config FB_XVR500
 890         bool "Sun XVR-500 3DLABS Wildcat support"
 891         depends on (FB = y) && PCI && SPARC64
 892         select FB_CFB_FILLRECT
 893         select FB_CFB_COPYAREA
 894         select FB_CFB_IMAGEBLIT
 895         help
 896           This is the framebuffer device for the Sun XVR-500 and similar
 897           graphics cards based upon the 3DLABS Wildcat chipset.  The driver
 898           only works on sparc64 systems where the system firmware has
 899           mostly initialized the card already.  It is treated as a
 900           completely dumb framebuffer device.
 901
 902 config FB_XVR2500
 903         bool "Sun XVR-2500 3DLABS Wildcat support"
 904         depends on (FB = y) && PCI && SPARC64
 905         select FB_CFB_FILLRECT
 906         select FB_CFB_COPYAREA
 907         select FB_CFB_IMAGEBLIT
 908         help
 909           This is the framebuffer device for the Sun XVR-2500 and similar
 910           graphics cards based upon the 3DLABS Wildcat chipset.  The driver
 911           only works on sparc64 systems where the system firmware has
 912           mostly initialized the card already.  It is treated as a
 913           completely dumb framebuffer device.
 914
 915 config FB_XVR1000
 916         bool "Sun XVR-1000 support"
 917         depends on (FB = y) && SPARC64
 918         select FB_CFB_FILLRECT
 919         select FB_CFB_COPYAREA
 920         select FB_CFB_IMAGEBLIT
 921         help
 922           This is the framebuffer device for the Sun XVR-1000 and similar
 923           graphics cards.  The driver only works on sparc64 systems where
 924           the system firmware has mostly initialized the card already.  It
 925           is treated as a completely dumb framebuffer device.
 926
 927 config FB_PVR2
 928         tristate "NEC PowerVR 2 display support"
 929         depends on FB && SH_DREAMCAST
 930         select FB_CFB_FILLRECT
 931         select FB_CFB_COPYAREA
 932         select FB_CFB_IMAGEBLIT
 933         ---help---
 934           Say Y here if you have a PowerVR 2 card in your box.  If you plan to
 935           run linux on your Dreamcast, you will have to say Y here.
 936           This driver may or may not work on other PowerVR 2 cards, but is
 937           totally untested.  Use at your own risk.  If unsure, say N.
 938
 939           To compile this driver as a module, choose M here: the
 940           module will be called pvr2fb.
 941
 942           You can pass several parameters to the driver at boot time or at
 943           module load time.  The parameters look like "video=pvr2:XXX", where
 944           the meaning of XXX can be found at the end of the main source file
 945           (<file:drivers/video/pvr2fb.c>). Please see the file
 946           <file:Documentation/fb/pvr2fb.txt>.
 947
 948 config FB_EPSON1355
 949         bool "Epson 1355 framebuffer support"
 950         depends on (FB = y) && ARCH_CEIVA
 951         select FB_CFB_FILLRECT
 952         select FB_CFB_COPYAREA
 953         select FB_CFB_IMAGEBLIT
 954         help
 955           Build in support for the SED1355 Epson Research Embedded RAMDAC
 956           LCD/CRT Controller (since redesignated as the S1D13505) as a
 957           framebuffer.  Product specs at
 958           <http://www.erd.epson.com/vdc/html/products.htm>.
 959
 960 config FB_S1D13XXX
 961         tristate "Epson S1D13XXX framebuffer support"
 962         depends on FB
 963         select FB_CFB_FILLRECT
 964         select FB_CFB_COPYAREA
 965         select FB_CFB_IMAGEBLIT
 966         help
 967           Support for S1D13XXX framebuffer device family (currently only
 968           working with S1D13806). Product specs at
 969           <http://www.erd.epson.com/vdc/html/legacy_13xxx.htm>
 970
 971 config FB_ATMEL
 972         tristate "AT91/AT32 LCD Controller support"
 973         depends on FB && HAVE_FB_ATMEL
 974         select FB_CFB_FILLRECT
 975         select FB_CFB_COPYAREA
 976         select FB_CFB_IMAGEBLIT
 977         help
 978           This enables support for the AT91/AT32 LCD Controller.
 979
 980 config FB_INTSRAM
 981         bool "Frame Buffer in internal SRAM"
 982         depends on FB_ATMEL && ARCH_AT91SAM9261
 983         help
 984           Say Y if you want to map Frame Buffer in internal SRAM. Say N if you want
 985           to let frame buffer in external SDRAM.
 986
 987 config FB_ATMEL_STN
 988         bool "Use a STN display with AT91/AT32 LCD Controller"
 989         depends on FB_ATMEL && (MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK)
 990         default n
 991         help
 992           Say Y if you want to connect a STN LCD display to the AT91/AT32 LCD
 993           Controller. Say N if you want to connect a TFT.
 994
 995           If unsure, say N.
 996
 997 config FB_NVIDIA
 998         tristate "nVidia Framebuffer Support"
 999         depends on FB && PCI
1000         select FB_BACKLIGHT if FB_NVIDIA_BACKLIGHT
1001         select FB_MODE_HELPERS
1002         select FB_CFB_FILLRECT
1003         select FB_CFB_COPYAREA
1004         select FB_CFB_IMAGEBLIT
1005         select BITREVERSE
1006         select VGASTATE
1007         help
1008           This driver supports graphics boards with the nVidia chips, TNT
1009           and newer. For very old chipsets, such as the RIVA128, then use
1010           the rivafb.
1011           Say Y if you have such a graphics board.
1012
1013           To compile this driver as a module, choose M here: the
1014           module will be called nvidiafb.
1015
1016 config FB_NVIDIA_I2C
1017        bool "Enable DDC Support"
1018        depends on FB_NVIDIA
1019        select FB_DDC
1020        help
1021           This enables I2C support for nVidia Chipsets.  This is used
1022           only for getting EDID information from the attached display
1023           allowing for robust video mode handling and switching.
1024
1025           Because fbdev-2.6 requires that drivers must be able to
1026           independently validate video mode parameters, you should say Y
1027           here.
1028
1029 config FB_NVIDIA_DEBUG
1030         bool "Lots of debug output"
1031         depends on FB_NVIDIA
1032         default n
1033         help
1034           Say Y here if you want the nVidia driver to output all sorts
1035           of debugging information to provide to the maintainer when
1036           something goes wrong.
1037
1038 config FB_NVIDIA_BACKLIGHT
1039         bool "Support for backlight control"
1040         depends on FB_NVIDIA
1041         default y
1042         help
1043           Say Y here if you want to control the backlight of your display.
1044
1045 config FB_RIVA
1046         tristate "nVidia Riva support"
1047         depends on FB && PCI
1048         select FB_BACKLIGHT if FB_RIVA_BACKLIGHT
1049         select FB_MODE_HELPERS
1050         select FB_CFB_FILLRECT
1051         select FB_CFB_COPYAREA
1052         select FB_CFB_IMAGEBLIT
1053         select BITREVERSE
1054         select VGASTATE
1055         help
1056           This driver supports graphics boards with the nVidia Riva/Geforce
1057           chips.
1058           Say Y if you have such a graphics board.
1059
1060           To compile this driver as a module, choose M here: the
1061           module will be called rivafb.
1062
1063 config FB_RIVA_I2C
1064        bool "Enable DDC Support"
1065        depends on FB_RIVA
1066        select FB_DDC
1067        help
1068           This enables I2C support for nVidia Chipsets.  This is used
1069           only for getting EDID information from the attached display
1070           allowing for robust video mode handling and switching.
1071
1072           Because fbdev-2.6 requires that drivers must be able to
1073           independently validate video mode parameters, you should say Y
1074           here.
1075
1076 config FB_RIVA_DEBUG
1077         bool "Lots of debug output"
1078         depends on FB_RIVA
1079         default n
1080         help
1081           Say Y here if you want the Riva driver to output all sorts
1082           of debugging information to provide to the maintainer when
1083           something goes wrong.
1084
1085 config FB_RIVA_BACKLIGHT
1086         bool "Support for backlight control"
1087         depends on FB_RIVA
1088         default y
1089         help
1090           Say Y here if you want to control the backlight of your display.
1091
1092 config FB_I810
1093         tristate "Intel 810/815 support (EXPERIMENTAL)"
1094         depends on EXPERIMENTAL && FB && PCI && X86_32 && AGP_INTEL
1095         select FB_MODE_HELPERS
1096         select FB_CFB_FILLRECT
1097         select FB_CFB_COPYAREA
1098         select FB_CFB_IMAGEBLIT
1099         select VGASTATE
1100         help
1101           This driver supports the on-board graphics built in to the Intel 810
1102           and 815 chipsets.  Say Y if you have and plan to use such a board.
1103
1104           To compile this driver as a module, choose M here: the
1105           module will be called i810fb.
1106
1107           For more information, please read
1108           <file:Documentation/fb/intel810.txt>
1109
1110 config FB_I810_GTF
1111         bool "use VESA Generalized Timing Formula"
1112         depends on FB_I810
1113         help
1114           If you say Y, then the VESA standard, Generalized Timing Formula
1115           or GTF, will be used to calculate the required video timing values
1116           per video mode.  Since the GTF allows nondiscrete timings
1117           (nondiscrete being a range of values as opposed to discrete being a
1118           set of values), you'll be able to use any combination of horizontal
1119           and vertical resolutions, and vertical refresh rates without having
1120           to specify your own timing parameters.  This is especially useful
1121           to maximize the performance of an aging display, or if you just
1122           have a display with nonstandard dimensions. A VESA compliant
1123           monitor is recommended, but can still work with non-compliant ones.
1124           If you need or want this, then select this option. The timings may
1125           not be compliant with Intel's recommended values. Use at your own
1126           risk.
1127
1128           If you say N, the driver will revert to discrete video timings
1129           using a set recommended by Intel in their documentation.
1130
1131           If unsure, say N.
1132
1133 config FB_I810_I2C
1134         bool "Enable DDC Support"
1135         depends on FB_I810 && FB_I810_GTF
1136         select FB_DDC
1137         help
1138
1139 config FB_LE80578
1140         tristate "Intel LE80578 (Vermilion) support"
1141         depends on FB && PCI && X86
1142         select FB_MODE_HELPERS
1143         select FB_CFB_FILLRECT
1144         select FB_CFB_COPYAREA
1145         select FB_CFB_IMAGEBLIT
1146         help
1147           This driver supports the LE80578 (Vermilion Range) chipset
1148
1149 config FB_CARILLO_RANCH
1150         tristate "Intel Carillo Ranch support"
1151         depends on FB_LE80578 && FB && PCI && X86
1152         help
1153           This driver supports the LE80578 (Carillo Ranch) board
1154
1155 config FB_INTEL
1156         tristate "Intel 830M/845G/852GM/855GM/865G/915G/945G/945GM/965G/965GM support (EXPERIMENTAL)"
1157         depends on EXPERIMENTAL && FB && PCI && X86 && AGP_INTEL && EMBEDDED
1158         select FB_MODE_HELPERS
1159         select FB_CFB_FILLRECT
1160         select FB_CFB_COPYAREA
1161         select FB_CFB_IMAGEBLIT
1162         select FB_BOOT_VESA_SUPPORT if FB_INTEL = y
1163         depends on !DRM_I915
1164         help
1165           This driver supports the on-board graphics built in to the Intel
1166           830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/965G/965GM chipsets.
1167           Say Y if you have and plan to use such a board.
1168
1169           To make FB_INTELFB=Y work you need to say AGP_INTEL=y too.
1170
1171           To compile this driver as a module, choose M here: the
1172           module will be called intelfb.
1173
1174           For more information, please read <file:Documentation/fb/intelfb.txt>
1175
1176 config FB_INTEL_DEBUG
1177         bool "Intel driver Debug Messages"
1178         depends on FB_INTEL
1179         ---help---
1180           Say Y here if you want the Intel driver to output all sorts
1181           of debugging information to provide to the maintainer when
1182           something goes wrong.
1183
1184 config FB_INTEL_I2C
1185         bool "DDC/I2C for Intel framebuffer support"
1186         depends on FB_INTEL
1187         select FB_DDC
1188         default y
1189         help
1190           Say Y here if you want DDC/I2C support for your on-board Intel graphics.
1191
1192 config FB_MATROX
1193         tristate "Matrox acceleration"
1194         depends on FB && PCI
1195         select FB_CFB_FILLRECT
1196         select FB_CFB_COPYAREA
1197         select FB_CFB_IMAGEBLIT
1198         select FB_TILEBLITTING
1199         select FB_MACMODES if PPC_PMAC
1200         ---help---
1201           Say Y here if you have a Matrox Millennium, Matrox Millennium II,
1202           Matrox Mystique, Matrox Mystique 220, Matrox Productiva G100, Matrox
1203           Mystique G200, Matrox Millennium G200, Matrox Marvel G200 video,
1204           Matrox G400, G450 or G550 card in your box.
1205
1206           To compile this driver as a module, choose M here: the
1207           module will be called matroxfb.
1208
1209           You can pass several parameters to the driver at boot time or at
1210           module load time. The parameters look like "video=matrox:XXX", and
1211           are described in <file:Documentation/fb/matroxfb.txt>.
1212
1213 config FB_MATROX_MILLENIUM
1214         bool "Millennium I/II support"
1215         depends on FB_MATROX
1216         help
1217           Say Y here if you have a Matrox Millennium or Matrox Millennium II
1218           video card. If you select "Advanced lowlevel driver options" below,
1219           you should check 4 bpp packed pixel, 8 bpp packed pixel, 16 bpp
1220           packed pixel, 24 bpp packed pixel and 32 bpp packed pixel. You can
1221           also use font widths different from 8.
1222
1223 config FB_MATROX_MYSTIQUE
1224         bool "Mystique support"
1225         depends on FB_MATROX
1226         help
1227           Say Y here if you have a Matrox Mystique or Matrox Mystique 220
1228           video card. If you select "Advanced lowlevel driver options" below,
1229           you should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp
1230           packed pixel and 32 bpp packed pixel. You can also use font widths
1231           different from 8.
1232
1233 config FB_MATROX_G
1234         bool "G100/G200/G400/G450/G550 support"
1235         depends on FB_MATROX
1236         ---help---
1237           Say Y here if you have a Matrox G100, G200, G400, G450 or G550 based
1238           video card. If you select "Advanced lowlevel driver options", you
1239           should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp packed
1240           pixel and 32 bpp packed pixel. You can also use font widths
1241           different from 8.
1242
1243           If you need support for G400 secondary head, you must say Y to
1244           "Matrox I2C support" and "G400 second head support" right below.
1245           G450/G550 secondary head and digital output are supported without
1246           additional modules.
1247
1248           The driver starts in monitor mode. You must use the matroxset tool
1249           (available at <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to
1250           swap primary and secondary head outputs, or to change output mode.
1251           Secondary head driver always start in 640x480 resolution and you
1252           must use fbset to change it.
1253
1254           Do not forget that second head supports only 16 and 32 bpp
1255           packed pixels, so it is a good idea to compile them into the kernel
1256           too. You can use only some font widths, as the driver uses generic
1257           painting procedures (the secondary head does not use acceleration
1258           engine).
1259
1260           G450/G550 hardware can display TV picture only from secondary CRTC,
1261           and it performs no scaling, so picture must have 525 or 625 lines.
1262
1263 config FB_MATROX_I2C
1264         tristate "Matrox I2C support"
1265         depends on FB_MATROX
1266         select FB_DDC
1267         ---help---
1268           This drivers creates I2C buses which are needed for accessing the
1269           DDC (I2C) bus present on all Matroxes, an I2C bus which
1270           interconnects Matrox optional devices, like MGA-TVO on G200 and
1271           G400, and the secondary head DDC bus, present on G400 only.
1272
1273           You can say Y or M here if you want to experiment with monitor
1274           detection code. You must say Y or M here if you want to use either
1275           second head of G400 or MGA-TVO on G200 or G400.
1276
1277           If you compile it as module, it will create a module named
1278           i2c-matroxfb.
1279
1280 config FB_MATROX_MAVEN
1281         tristate "G400 second head support"
1282         depends on FB_MATROX_G && FB_MATROX_I2C
1283         ---help---
1284           WARNING !!! This support does not work with G450 !!!
1285
1286           Say Y or M here if you want to use a secondary head (meaning two
1287           monitors in parallel) on G400 or MGA-TVO add-on on G200. Secondary
1288           head is not compatible with accelerated XFree 3.3.x SVGA servers -
1289           secondary head output is blanked while you are in X. With XFree
1290           3.9.17 preview you can use both heads if you use SVGA over fbdev or
1291           the fbdev driver on first head and the fbdev driver on second head.
1292
1293           If you compile it as module, two modules are created,
1294           matroxfb_crtc2 and matroxfb_maven. Matroxfb_maven is needed for
1295           both G200 and G400, matroxfb_crtc2 is needed only by G400. You must
1296           also load i2c-matroxfb to get it to run.
1297
1298           The driver starts in monitor mode and you must use the matroxset
1299           tool (available at
1300           <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to switch it to
1301           PAL or NTSC or to swap primary and secondary head outputs.
1302           Secondary head driver also always start in 640x480 resolution, you
1303           must use fbset to change it.
1304
1305           Also do not forget that second head supports only 16 and 32 bpp
1306           packed pixels, so it is a good idea to compile them into the kernel
1307           too.  You can use only some font widths, as the driver uses generic
1308           painting procedures (the secondary head does not use acceleration
1309           engine).
1310
1311 config FB_RADEON
1312         tristate "ATI Radeon display support"
1313         depends on FB && PCI
1314         select FB_BACKLIGHT if FB_RADEON_BACKLIGHT
1315         select FB_MODE_HELPERS
1316         select FB_CFB_FILLRECT
1317         select FB_CFB_COPYAREA
1318         select FB_CFB_IMAGEBLIT
1319         select FB_MACMODES if PPC_OF
1320         help
1321           Choose this option if you want to use an ATI Radeon graphics card as
1322           a framebuffer device.  There are both PCI and AGP versions.  You
1323           don't need to choose this to run the Radeon in plain VGA mode.
1324
1325           There is a product page at
1326           http://apps.ati.com/ATIcompare/
1327
1328 config FB_RADEON_I2C
1329         bool "DDC/I2C for ATI Radeon support"
1330         depends on FB_RADEON
1331         select FB_DDC
1332         default y
1333         help
1334           Say Y here if you want DDC/I2C support for your Radeon board.
1335
1336 config FB_RADEON_BACKLIGHT
1337         bool "Support for backlight control"
1338         depends on FB_RADEON
1339         default y
1340         help
1341           Say Y here if you want to control the backlight of your display.
1342
1343 config FB_RADEON_DEBUG
1344         bool "Lots of debug output from Radeon driver"
1345         depends on FB_RADEON
1346         default n
1347         help
1348           Say Y here if you want the Radeon driver to output all sorts
1349           of debugging information to provide to the maintainer when
1350           something goes wrong.
1351
1352 config FB_ATY128
1353         tristate "ATI Rage128 display support"
1354         depends on FB && PCI
1355         select FB_CFB_FILLRECT
1356         select FB_CFB_COPYAREA
1357         select FB_CFB_IMAGEBLIT
1358         select FB_BACKLIGHT if FB_ATY128_BACKLIGHT
1359         select FB_MACMODES if PPC_PMAC
1360         help
1361           This driver supports graphics boards with the ATI Rage128 chips.
1362           Say Y if you have such a graphics board and read
1363           <file:Documentation/fb/aty128fb.txt>.
1364
1365           To compile this driver as a module, choose M here: the
1366           module will be called aty128fb.
1367
1368 config FB_ATY128_BACKLIGHT
1369         bool "Support for backlight control"
1370         depends on FB_ATY128
1371         default y
1372         help
1373           Say Y here if you want to control the backlight of your display.
1374
1375 config FB_ATY
1376         tristate "ATI Mach64 display support" if PCI || ATARI
1377         depends on FB && !SPARC32
1378         select FB_CFB_FILLRECT
1379         select FB_CFB_COPYAREA
1380         select FB_CFB_IMAGEBLIT
1381         select FB_BACKLIGHT if FB_ATY_BACKLIGHT
1382         select FB_MACMODES if PPC
1383         help
1384           This driver supports graphics boards with the ATI Mach64 chips.
1385           Say Y if you have such a graphics board.
1386
1387           To compile this driver as a module, choose M here: the
1388           module will be called atyfb.
1389
1390 config FB_ATY_CT
1391         bool "Mach64 CT/VT/GT/LT (incl. 3D RAGE) support"
1392         depends on PCI && FB_ATY
1393         default y if SPARC64 && PCI
1394         help
1395           Say Y here to support use of ATI's 64-bit Rage boards (or other
1396           boards based on the Mach64 CT, VT, GT, and LT chipsets) as a
1397           framebuffer device.  The ATI product support page for these boards
1398           is at <http://support.ati.com/products/pc/mach64/>.
1399
1400 config FB_ATY_GENERIC_LCD
1401         bool "Mach64 generic LCD support (EXPERIMENTAL)"
1402         depends on FB_ATY_CT
1403         help
1404           Say Y if you have a laptop with an ATI Rage LT PRO, Rage Mobility,
1405           Rage XC, or Rage XL chipset.
1406
1407 config FB_ATY_GX
1408         bool "Mach64 GX support" if PCI
1409         depends on FB_ATY
1410         default y if ATARI
1411         help
1412           Say Y here to support use of the ATI Mach64 Graphics Expression
1413           board (or other boards based on the Mach64 GX chipset) as a
1414           framebuffer device.  The ATI product support page for these boards
1415           is at
1416           <http://support.ati.com/products/pc/mach64/graphics_xpression.html>.
1417
1418 config FB_ATY_BACKLIGHT
1419         bool "Support for backlight control"
1420         depends on FB_ATY
1421         default y
1422         help
1423           Say Y here if you want to control the backlight of your display.
1424
1425 config FB_S3
1426         tristate "S3 Trio/Virge support"
1427         depends on FB && PCI
1428         select FB_CFB_FILLRECT
1429         select FB_CFB_COPYAREA
1430         select FB_CFB_IMAGEBLIT
1431         select FB_TILEBLITTING
1432         select FB_SVGALIB
1433         select VGASTATE
1434         select FONT_8x16 if FRAMEBUFFER_CONSOLE
1435         ---help---
1436           Driver for graphics boards with S3 Trio / S3 Virge chip.
1437
1438 config FB_SAVAGE
1439         tristate "S3 Savage support"
1440         depends on FB && PCI && EXPERIMENTAL
1441         select FB_MODE_HELPERS
1442         select FB_CFB_FILLRECT
1443         select FB_CFB_COPYAREA
1444         select FB_CFB_IMAGEBLIT
1445         select VGASTATE
1446         help
1447           This driver supports notebooks and computers with S3 Savage PCI/AGP
1448           chips.
1449
1450           Say Y if you have such a graphics card.
1451
1452           To compile this driver as a module, choose M here; the module
1453           will be called savagefb.
1454
1455 config FB_SAVAGE_I2C
1456        bool "Enable DDC2 Support"
1457        depends on FB_SAVAGE
1458        select FB_DDC
1459        help
1460           This enables I2C support for S3 Savage Chipsets.  This is used
1461           only for getting EDID information from the attached display
1462           allowing for robust video mode handling and switching.
1463
1464           Because fbdev-2.6 requires that drivers must be able to
1465           independently validate video mode parameters, you should say Y
1466           here.
1467
1468 config FB_SAVAGE_ACCEL
1469        bool "Enable Console Acceleration"
1470        depends on FB_SAVAGE
1471        default n
1472        help
1473           This option will compile in console acceleration support. If
1474           the resulting framebuffer console has bothersome glitches, then
1475           choose N here.
1476
1477 config FB_SIS
1478         tristate "SiS/XGI display support"
1479         depends on FB && PCI
1480         select FB_CFB_FILLRECT
1481         select FB_CFB_COPYAREA
1482         select FB_CFB_IMAGEBLIT
1483         select FB_BOOT_VESA_SUPPORT if FB_SIS = y
1484         help
1485           This is the frame buffer device driver for the SiS 300, 315, 330
1486           and 340 series as well as XGI V3XT, V5, V8, Z7 graphics chipsets.
1487           Specs available at <http://www.sis.com> and <http://www.xgitech.com>.
1488
1489           To compile this driver as a module, choose M here; the module
1490           will be called sisfb.
1491
1492 config FB_SIS_300
1493         bool "SiS 300 series support"
1494         depends on FB_SIS
1495         help
1496           Say Y here to support use of the SiS 300/305, 540, 630 and 730.
1497
1498 config FB_SIS_315
1499         bool "SiS 315/330/340 series and XGI support"
1500         depends on FB_SIS
1501         help
1502           Say Y here to support use of the SiS 315, 330 and 340 series
1503           (315/H/PRO, 55x, 650, 651, 740, 330, 661, 741, 760, 761) as well
1504           as XGI V3XT, V5, V8 and Z7.
1505
1506 config FB_VIA
1507        tristate "VIA UniChrome (Pro) and Chrome9 display support"
1508        depends on FB && PCI && X86
1509        select FB_CFB_FILLRECT
1510        select FB_CFB_COPYAREA
1511        select FB_CFB_IMAGEBLIT
1512        select I2C_ALGOBIT
1513        select I2C
1514        select GPIOLIB
1515        help
1516           This is the frame buffer device driver for Graphics chips of VIA
1517           UniChrome (Pro) Family (CLE266,PM800/CN400,P4M800CE/P4M800Pro/
1518           CN700/VN800,CX700/VX700,P4M890) and Chrome9 Family (K8M890,CN896
1519           /P4M900,VX800)
1520           Say Y if you have a VIA UniChrome graphics board.
1521
1522           To compile this driver as a module, choose M here: the
1523           module will be called viafb.
1524
1525 if FB_VIA
1526
1527 config FB_VIA_DIRECT_PROCFS
1528         bool "direct hardware access via procfs (DEPRECATED)(DANGEROUS)"
1529         depends on FB_VIA
1530         default n
1531         help
1532           Allow direct hardware access to some output registers via procfs.
1533           This is dangerous but may provide the only chance to get the
1534           correct output device configuration.
1535           Its use is strongly discouraged.
1536
1537 endif
1538
1539 config FB_NEOMAGIC
1540         tristate "NeoMagic display support"
1541         depends on FB && PCI
1542         select FB_MODE_HELPERS
1543         select FB_CFB_FILLRECT
1544         select FB_CFB_COPYAREA
1545         select FB_CFB_IMAGEBLIT
1546         select VGASTATE
1547         help
1548           This driver supports notebooks with NeoMagic PCI chips.
1549           Say Y if you have such a graphics card.
1550
1551           To compile this driver as a module, choose M here: the
1552           module will be called neofb.
1553
1554 config FB_KYRO
1555         tristate "IMG Kyro support"
1556         depends on FB && PCI
1557         select FB_CFB_FILLRECT
1558         select FB_CFB_COPYAREA
1559         select FB_CFB_IMAGEBLIT
1560         help
1561           Say Y here if you have a STG4000 / Kyro / PowerVR 3 based
1562           graphics board.
1563
1564           To compile this driver as a module, choose M here: the
1565           module will be called kyrofb.
1566
1567 config FB_3DFX
1568         tristate "3Dfx Banshee/Voodoo3/Voodoo5 display support"
1569         depends on FB && PCI
1570         select FB_CFB_IMAGEBLIT
1571         select FB_CFB_FILLRECT
1572         select FB_CFB_COPYAREA
1573         select FB_MODE_HELPERS
1574         help
1575           This driver supports graphics boards with the 3Dfx Banshee,
1576           Voodoo3 or VSA-100 (aka Voodoo4/5) chips. Say Y if you have
1577           such a graphics board.
1578
1579           To compile this driver as a module, choose M here: the
1580           module will be called tdfxfb.
1581
1582 config FB_3DFX_ACCEL
1583         bool "3Dfx Acceleration functions (EXPERIMENTAL)"
1584         depends on FB_3DFX && EXPERIMENTAL
1585         ---help---
1586         This will compile the 3Dfx Banshee/Voodoo3/VSA-100 frame buffer
1587         device driver with acceleration functions.
1588
1589 config FB_3DFX_I2C
1590         bool "Enable DDC/I2C support"
1591         depends on FB_3DFX && EXPERIMENTAL
1592         select FB_DDC
1593         default y
1594         help
1595           Say Y here if you want DDC/I2C support for your 3dfx Voodoo3.
1596
1597 config FB_VOODOO1
1598         tristate "3Dfx Voodoo Graphics (sst1) support"
1599         depends on FB && PCI
1600         select FB_CFB_FILLRECT
1601         select FB_CFB_COPYAREA
1602         select FB_CFB_IMAGEBLIT
1603         ---help---
1604           Say Y here if you have a 3Dfx Voodoo Graphics (Voodoo1/sst1) or
1605           Voodoo2 (cvg) based graphics card.
1606
1607           To compile this driver as a module, choose M here: the
1608           module will be called sstfb.
1609
1610           WARNING: Do not use any application that uses the 3D engine
1611           (namely glide) while using this driver.
1612           Please read the <file:Documentation/fb/sstfb.txt> for supported
1613           options and other important info  support.
1614
1615 config FB_VT8623
1616         tristate "VIA VT8623 support"
1617         depends on FB && PCI
1618         select FB_CFB_FILLRECT
1619         select FB_CFB_COPYAREA
1620         select FB_CFB_IMAGEBLIT
1621         select FB_TILEBLITTING
1622         select FB_SVGALIB
1623         select VGASTATE
1624         select FONT_8x16 if FRAMEBUFFER_CONSOLE
1625         ---help---
1626           Driver for CastleRock integrated graphics core in the
1627           VIA VT8623 [Apollo CLE266] chipset.
1628
1629 config FB_TRIDENT
1630         tristate "Trident/CyberXXX/CyberBlade support"
1631         depends on FB && PCI
1632         select FB_CFB_FILLRECT
1633         select FB_CFB_COPYAREA
1634         select FB_CFB_IMAGEBLIT
1635         ---help---
1636           This is the frame buffer device driver for Trident PCI/AGP chipsets.
1637           Supported chipset families are TGUI 9440/96XX, 3DImage, Blade3D
1638           and Blade XP.
1639           There are also integrated versions of these chips called CyberXXXX,
1640           CyberImage or CyberBlade. These chips are mostly found in laptops
1641           but also on some motherboards including early VIA EPIA motherboards.
1642           For more information, read <file:Documentation/fb/tridentfb.txt>
1643
1644           Say Y if you have such a graphics board.
1645
1646           To compile this driver as a module, choose M here: the
1647           module will be called tridentfb.
1648
1649 config FB_ARK
1650         tristate "ARK 2000PV support"
1651         depends on FB && PCI
1652         select FB_CFB_FILLRECT
1653         select FB_CFB_COPYAREA
1654         select FB_CFB_IMAGEBLIT
1655         select FB_TILEBLITTING
1656         select FB_SVGALIB
1657         select VGASTATE
1658         select FONT_8x16 if FRAMEBUFFER_CONSOLE
1659         ---help---
1660           Driver for PCI graphics boards with ARK 2000PV chip
1661           and ICS 5342 RAMDAC.
1662
1663 config FB_PM3
1664         tristate "Permedia3 support (EXPERIMENTAL)"
1665         depends on FB && PCI && EXPERIMENTAL
1666         select FB_CFB_FILLRECT
1667         select FB_CFB_COPYAREA
1668         select FB_CFB_IMAGEBLIT
1669         help
1670           This is the frame buffer device driver for the 3DLabs Permedia3
1671           chipset, used in Formac ProFormance III, 3DLabs Oxygen VX1 &
1672           similar boards, 3DLabs Permedia3 Create!, Appian Jeronimo 2000
1673           and maybe other boards.
1674
1675 config FB_CARMINE
1676         tristate "Fujitsu carmine frame buffer support"
1677         depends on FB && PCI
1678         select FB_CFB_FILLRECT
1679         select FB_CFB_COPYAREA
1680         select FB_CFB_IMAGEBLIT
1681         help
1682           This is the frame buffer device driver for the Fujitsu Carmine chip.
1683           The driver provides two independent frame buffer devices.
1684
1685 choice
1686         depends on FB_CARMINE
1687         prompt "DRAM timing"
1688         default FB_CARMINE_DRAM_EVAL
1689
1690 config FB_CARMINE_DRAM_EVAL
1691         bool "Eval board timings"
1692         help
1693           Use timings which work on the eval card.
1694
1695 config CARMINE_DRAM_CUSTOM
1696         bool "Custom board timings"
1697         help
1698           Use custom board timings.
1699 endchoice
1700
1701 config FB_AU1100
1702         bool "Au1100 LCD Driver"
1703         depends on (FB = y) && MIPS && SOC_AU1100
1704         select FB_CFB_FILLRECT
1705         select FB_CFB_COPYAREA
1706         select FB_CFB_IMAGEBLIT
1707         help
1708           This is the framebuffer driver for the AMD Au1100 SOC.  It can drive
1709           various panels and CRTs by passing in kernel cmd line option
1710           au1100fb:panel=<name>.
1711
1712 config FB_AU1200
1713         bool "Au1200 LCD Driver"
1714         depends on (FB = y) && MIPS && SOC_AU1200
1715         select FB_CFB_FILLRECT
1716         select FB_CFB_COPYAREA
1717         select FB_CFB_IMAGEBLIT
1718         help
1719           This is the framebuffer driver for the AMD Au1200 SOC.  It can drive
1720           various panels and CRTs by passing in kernel cmd line option
1721           au1200fb:panel=<name>.
1722
1723 source "drivers/video/geode/Kconfig"
1724
1725 config FB_HIT
1726         tristate "HD64461 Frame Buffer support"
1727         depends on FB && HD64461
1728         select FB_CFB_FILLRECT
1729         select FB_CFB_COPYAREA
1730         select FB_CFB_IMAGEBLIT
1731         help
1732           This is the frame buffer device driver for the Hitachi HD64461 LCD
1733           frame buffer card.
1734
1735 config FB_PMAG_AA
1736         bool "PMAG-AA TURBOchannel framebuffer support"
1737         depends on (FB = y) && TC
1738         select FB_CFB_FILLRECT
1739         select FB_CFB_COPYAREA
1740         select FB_CFB_IMAGEBLIT
1741         help
1742           Support for the PMAG-AA TURBOchannel framebuffer card (1280x1024x1)
1743           used mainly in the MIPS-based DECstation series.
1744
1745 config FB_PMAG_BA
1746         tristate "PMAG-BA TURBOchannel framebuffer support"
1747         depends on FB && TC
1748         select FB_CFB_FILLRECT
1749         select FB_CFB_COPYAREA
1750         select FB_CFB_IMAGEBLIT
1751         help
1752           Support for the PMAG-BA TURBOchannel framebuffer card (1024x864x8)
1753           used mainly in the MIPS-based DECstation series.
1754
1755 config FB_PMAGB_B
1756         tristate "PMAGB-B TURBOchannel framebuffer support"
1757         depends on FB && TC
1758         select FB_CFB_FILLRECT
1759         select FB_CFB_COPYAREA
1760         select FB_CFB_IMAGEBLIT
1761         help
1762           Support for the PMAGB-B TURBOchannel framebuffer card used mainly
1763           in the MIPS-based DECstation series. The card is currently only
1764           supported in 1280x1024x8 mode.
1765
1766 config FB_MAXINE
1767         bool "Maxine (Personal DECstation) onboard framebuffer support"
1768         depends on (FB = y) && MACH_DECSTATION
1769         select FB_CFB_FILLRECT
1770         select FB_CFB_COPYAREA
1771         select FB_CFB_IMAGEBLIT
1772         help
1773           Support for the onboard framebuffer (1024x768x8) in the Personal
1774           DECstation series (Personal DECstation 5000/20, /25, /33, /50,
1775           Codename "Maxine").
1776
1777 config FB_G364
1778         bool "G364 frame buffer support"
1779         depends on (FB = y) && (MIPS_MAGNUM_4000 || OLIVETTI_M700)
1780         select FB_CFB_FILLRECT
1781         select FB_CFB_COPYAREA
1782         select FB_CFB_IMAGEBLIT
1783         help
1784           The G364 driver is the framebuffer used in MIPS Magnum 4000 and
1785           Olivetti M700-10 systems.
1786
1787 config FB_68328
1788         bool "Motorola 68328 native frame buffer support"
1789         depends on (FB = y) && (M68328 || M68EZ328 || M68VZ328)
1790         select FB_CFB_FILLRECT
1791         select FB_CFB_COPYAREA
1792         select FB_CFB_IMAGEBLIT
1793         help
1794           Say Y here if you want to support the built-in frame buffer of
1795           the Motorola 68328 CPU family.
1796
1797 config FB_PXA168
1798         tristate "PXA168/910 LCD framebuffer support"
1799         depends on FB && (CPU_PXA168 || CPU_PXA910)
1800         select FB_CFB_FILLRECT
1801         select FB_CFB_COPYAREA
1802         select FB_CFB_IMAGEBLIT
1803         ---help---
1804           Frame buffer driver for the built-in LCD controller in the Marvell
1805           MMP processor.
1806
1807 config FB_PXA
1808         tristate "PXA LCD framebuffer support"
1809         depends on FB && ARCH_PXA
1810         select FB_CFB_FILLRECT
1811         select FB_CFB_COPYAREA
1812         select FB_CFB_IMAGEBLIT
1813         ---help---
1814           Frame buffer driver for the built-in LCD controller in the Intel
1815           PXA2x0 processor.
1816
1817           This driver is also available as a module ( = code which can be
1818           inserted and removed from the running kernel whenever you want). The
1819           module will be called pxafb. If you want to compile it as a module,
1820           say M here and read <file:Documentation/kbuild/modules.txt>.
1821
1822           If unsure, say N.
1823
1824 config FB_PXA_OVERLAY
1825         bool "Support PXA27x/PXA3xx Overlay(s) as framebuffer"
1826         default n
1827         depends on FB_PXA && (PXA27x || PXA3xx)
1828
1829 config FB_PXA_SMARTPANEL
1830         bool "PXA Smartpanel LCD support"
1831         default n
1832         depends on FB_PXA
1833
1834 config FB_PXA_PARAMETERS
1835         bool "PXA LCD command line parameters"
1836         default n
1837         depends on FB_PXA
1838         ---help---
1839           Enable the use of kernel command line or module parameters
1840           to configure the physical properties of the LCD panel when
1841           using the PXA LCD driver.
1842
1843           This option allows you to override the panel parameters
1844           supplied by the platform in order to support multiple
1845           different models of flatpanel. If you will only be using a
1846           single model of flatpanel then you can safely leave this
1847           option disabled.
1848
1849           <file:Documentation/fb/pxafb.txt> describes the available parameters.
1850
1851 config FB_MBX
1852         tristate "2700G LCD framebuffer support"
1853         depends on FB && ARCH_PXA
1854         select FB_CFB_FILLRECT
1855         select FB_CFB_COPYAREA
1856         select FB_CFB_IMAGEBLIT
1857         ---help---
1858           Framebuffer driver for the Intel 2700G (Marathon) Graphics
1859           Accelerator
1860
1861 config FB_MBX_DEBUG
1862        bool "Enable debugging info via debugfs"
1863        depends on FB_MBX && DEBUG_FS
1864        default n
1865        ---help---
1866          Enable this if you want debugging information using the debug
1867          filesystem (debugfs)
1868
1869          If unsure, say N.
1870
1871 config FB_FSL_DIU
1872         tristate "Freescale DIU framebuffer support"
1873         depends on FB && FSL_SOC
1874         select FB_MODE_HELPERS
1875         select FB_CFB_FILLRECT
1876         select FB_CFB_COPYAREA
1877         select FB_CFB_IMAGEBLIT
1878         select PPC_LIB_RHEAP
1879         ---help---
1880           Framebuffer driver for the Freescale SoC DIU
1881
1882 config FB_W100
1883         tristate "W100 frame buffer support"
1884         depends on FB && ARCH_PXA
1885         select FB_CFB_FILLRECT
1886         select FB_CFB_COPYAREA
1887         select FB_CFB_IMAGEBLIT
1888         ---help---
1889           Frame buffer driver for the w100 as found on the Sharp SL-Cxx series.
1890           It can also drive the w3220 chip found on iPAQ hx4700.
1891
1892           This driver is also available as a module ( = code which can be
1893           inserted and removed from the running kernel whenever you want). The
1894           module will be called w100fb. If you want to compile it as a module,
1895           say M here and read <file:Documentation/kbuild/modules.txt>.
1896
1897           If unsure, say N.
1898
1899 config SH_MIPI_DSI
1900         tristate
1901         depends on (SUPERH || ARCH_SHMOBILE) && HAVE_CLK
1902
1903 config SH_LCD_MIPI_DSI
1904         bool
1905
1906 config FB_SH_MOBILE_LCDC
1907         tristate "SuperH Mobile LCDC framebuffer support"
1908         depends on FB && (SUPERH || ARCH_SHMOBILE) && HAVE_CLK
1909         select FB_SYS_FILLRECT
1910         select FB_SYS_COPYAREA
1911         select FB_SYS_IMAGEBLIT
1912         select FB_SYS_FOPS
1913         select FB_DEFERRED_IO
1914         select SH_MIPI_DSI if SH_LCD_MIPI_DSI
1915         ---help---
1916           Frame buffer driver for the on-chip SH-Mobile LCD controller.
1917
1918 config FB_SH_MOBILE_HDMI
1919         tristate "SuperH Mobile HDMI controller support"
1920         depends on FB_SH_MOBILE_LCDC
1921         select FB_MODE_HELPERS
1922         ---help---
1923           Driver for the on-chip SH-Mobile HDMI controller.
1924
1925 config FB_TMIO
1926         tristate "Toshiba Mobile IO FrameBuffer support"
1927         depends on FB && MFD_CORE
1928         select FB_CFB_FILLRECT
1929         select FB_CFB_COPYAREA
1930         select FB_CFB_IMAGEBLIT
1931         ---help---
1932           Frame buffer driver for the Toshiba Mobile IO integrated as found
1933           on the Sharp SL-6000 series
1934
1935           This driver is also available as a module ( = code which can be
1936           inserted and removed from the running kernel whenever you want). The
1937           module will be called tmiofb. If you want to compile it as a module,
1938           say M here and read <file:Documentation/kbuild/modules.txt>.
1939
1940           If unsure, say N.
1941
1942 config FB_TMIO_ACCELL
1943         bool "tmiofb acceleration"
1944         depends on FB_TMIO
1945         default y
1946
1947 config FB_S3C
1948         tristate "Samsung S3C framebuffer support"
1949         depends on FB && S3C_DEV_FB
1950         select FB_CFB_FILLRECT
1951         select FB_CFB_COPYAREA
1952         select FB_CFB_IMAGEBLIT
1953         ---help---
1954           Frame buffer driver for the built-in FB controller in the Samsung
1955           SoC line from the S3C2443 onwards, including the S3C2416, S3C2450,
1956           and the S3C64XX series such as the S3C6400 and S3C6410.
1957
1958           These chips all have the same basic framebuffer design with the
1959           actual capabilities depending on the chip. For instance the S3C6400
1960           and S3C6410 support 4 hardware windows whereas the S3C24XX series
1961           currently only have two.
1962
1963           Currently the support is only for the S3C6400 and S3C6410 SoCs.
1964
1965 config FB_S3C_DEBUG_REGWRITE
1966        bool "Debug register writes"
1967        depends on FB_S3C
1968        ---help---
1969          Show all register writes via printk(KERN_DEBUG)
1970
1971 config FB_S3C2410
1972         tristate "S3C2410 LCD framebuffer support"
1973         depends on FB && ARCH_S3C2410
1974         select FB_CFB_FILLRECT
1975         select FB_CFB_COPYAREA
1976         select FB_CFB_IMAGEBLIT
1977         ---help---
1978           Frame buffer driver for the built-in LCD controller in the Samsung
1979           S3C2410 processor.
1980
1981           This driver is also available as a module ( = code which can be
1982           inserted and removed from the running kernel whenever you want). The
1983           module will be called s3c2410fb. If you want to compile it as a module,
1984           say M here and read <file:Documentation/kbuild/modules.txt>.
1985
1986           If unsure, say N.
1987 config FB_S3C2410_DEBUG
1988         bool "S3C2410 lcd debug messages"
1989         depends on FB_S3C2410
1990         help
1991           Turn on debugging messages. Note that you can set/unset at run time
1992           through sysfs
1993
1994 config FB_NUC900
1995         bool "NUC900 LCD framebuffer support"
1996         depends on FB && ARCH_W90X900
1997         select FB_CFB_FILLRECT
1998         select FB_CFB_COPYAREA
1999         select FB_CFB_IMAGEBLIT
2000         ---help---
2001           Frame buffer driver for the built-in LCD controller in the Nuvoton
2002           NUC900 processor
2003
2004 config GPM1040A0_320X240
2005         bool "Giantplus Technology GPM1040A0 320x240 Color TFT LCD"
2006         depends on FB_NUC900
2007
2008 config FB_NUC900_DEBUG
2009         bool "NUC900 lcd debug messages"
2010         depends on FB_NUC900
2011         help
2012           Turn on debugging messages. Note that you can set/unset at run time
2013           through sysfs
2014
2015 config FB_SM501
2016         tristate "Silicon Motion SM501 framebuffer support"
2017         depends on FB && MFD_SM501
2018         select FB_CFB_FILLRECT
2019         select FB_CFB_COPYAREA
2020         select FB_CFB_IMAGEBLIT
2021         ---help---
2022           Frame buffer driver for the CRT and LCD controllers in the Silicon
2023           Motion SM501.
2024
2025           This driver is also available as a module ( = code which can be
2026           inserted and removed from the running kernel whenever you want). The
2027           module will be called sm501fb. If you want to compile it as a module,
2028           say M here and read <file:Documentation/kbuild/modules.txt>.
2029
2030           If unsure, say N.
2031
2032
2033 config FB_PNX4008_DUM
2034         tristate "Display Update Module support on Philips PNX4008 board"
2035         depends on FB && ARCH_PNX4008
2036         ---help---
2037           Say Y here to enable support for PNX4008 Display Update Module (DUM)
2038
2039 config FB_PNX4008_DUM_RGB
2040         tristate "RGB Framebuffer support on Philips PNX4008 board"
2041         depends on FB_PNX4008_DUM
2042         select FB_CFB_FILLRECT
2043         select FB_CFB_COPYAREA
2044         select FB_CFB_IMAGEBLIT
2045         ---help---
2046           Say Y here to enable support for PNX4008 RGB Framebuffer
2047
2048 config FB_IBM_GXT4500
2049         tristate "Framebuffer support for IBM GXT4500P adaptor"
2050         depends on FB && PPC
2051         select FB_CFB_FILLRECT
2052         select FB_CFB_COPYAREA
2053         select FB_CFB_IMAGEBLIT
2054         ---help---
2055           Say Y here to enable support for the IBM GXT4500P display
2056           adaptor, found on some IBM System P (pSeries) machines.
2057
2058 config FB_PS3
2059         tristate "PS3 GPU framebuffer driver"
2060         depends on FB && PS3_PS3AV
2061         select FB_SYS_FILLRECT
2062         select FB_SYS_COPYAREA
2063         select FB_SYS_IMAGEBLIT
2064         select FB_SYS_FOPS
2065         select VT_HW_CONSOLE_BINDING if FRAMEBUFFER_CONSOLE
2066         ---help---
2067           Include support for the virtual frame buffer in the PS3 platform.
2068
2069 config FB_PS3_DEFAULT_SIZE_M
2070         int "PS3 default frame buffer size (in MiB)"
2071         depends on FB_PS3
2072         default 9
2073         ---help---
2074           This is the default size (in MiB) of the virtual frame buffer in
2075           the PS3.
2076           The default value can be overridden on the kernel command line
2077           using the "ps3fb" option (e.g. "ps3fb=9M");
2078
2079 config FB_XILINX
2080         tristate "Xilinx frame buffer support"
2081         depends on FB && (XILINX_VIRTEX || MICROBLAZE)
2082         select FB_CFB_FILLRECT
2083         select FB_CFB_COPYAREA
2084         select FB_CFB_IMAGEBLIT
2085         ---help---
2086           Include support for the Xilinx ML300/ML403 reference design
2087           framebuffer. ML300 carries a 640*480 LCD display on the board,
2088           ML403 uses a standard DB15 VGA connector.
2089
2090 config FB_COBALT
2091         tristate "Cobalt server LCD frame buffer support"
2092         depends on FB && MIPS_COBALT
2093
2094 config FB_SH7760
2095         bool "SH7760/SH7763/SH7720/SH7721 LCDC support"
2096         depends on FB && (CPU_SUBTYPE_SH7760 || CPU_SUBTYPE_SH7763 \
2097                 || CPU_SUBTYPE_SH7720 || CPU_SUBTYPE_SH7721)
2098         select FB_CFB_FILLRECT
2099         select FB_CFB_COPYAREA
2100         select FB_CFB_IMAGEBLIT
2101         ---help---
2102           Support for the SH7760/SH7763/SH7720/SH7721 integrated
2103           (D)STN/TFT LCD Controller.
2104           Supports display resolutions up to 1024x1024 pixel, grayscale and
2105           color operation, with depths ranging from 1 bpp to 8 bpp monochrome
2106           and 8, 15 or 16 bpp color; 90 degrees clockwise display rotation for
2107           panels <= 320 pixel horizontal resolution.
2108
2109 config FB_DA8XX
2110         tristate "DA8xx/OMAP-L1xx Framebuffer support"
2111         depends on FB && ARCH_DAVINCI_DA8XX
2112         select FB_CFB_FILLRECT
2113         select FB_CFB_COPYAREA
2114         select FB_CFB_IMAGEBLIT
2115         ---help---
2116           This is the frame buffer device driver for the TI LCD controller
2117           found on DA8xx/OMAP-L1xx SoCs.
2118           If unsure, say N.
2119
2120 config FB_VIRTUAL
2121         tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)"
2122         depends on FB
2123         select FB_SYS_FILLRECT
2124         select FB_SYS_COPYAREA
2125         select FB_SYS_IMAGEBLIT
2126         select FB_SYS_FOPS
2127         ---help---
2128           This is a `virtual' frame buffer device. It operates on a chunk of
2129           unswappable kernel memory instead of on the memory of a graphics
2130           board. This means you cannot see any output sent to this frame
2131           buffer device, while it does consume precious memory. The main use
2132           of this frame buffer device is testing and debugging the frame
2133           buffer subsystem. Do NOT enable it for normal systems! To protect
2134           the innocent, it has to be enabled explicitly at boot time using the
2135           kernel option `video=vfb:'.
2136
2137           To compile this driver as a module, choose M here: the
2138           module will be called vfb. In order to load it, you must use
2139           the vfb_enable=1 option.
2140
2141           If unsure, say N.
2142
2143 config XEN_FBDEV_FRONTEND
2144         tristate "Xen virtual frame buffer support"
2145         depends on FB && XEN
2146         select FB_SYS_FILLRECT
2147         select FB_SYS_COPYAREA
2148         select FB_SYS_IMAGEBLIT
2149         select FB_SYS_FOPS
2150         select FB_DEFERRED_IO
2151         select XEN_XENBUS_FRONTEND
2152         default y
2153         help
2154           This driver implements the front-end of the Xen virtual
2155           frame buffer driver.  It communicates with a back-end
2156           in another domain.
2157
2158 config FB_METRONOME
2159         tristate "E-Ink Metronome/8track controller support"
2160         depends on FB
2161         select FB_SYS_FILLRECT
2162         select FB_SYS_COPYAREA
2163         select FB_SYS_IMAGEBLIT
2164         select FB_SYS_FOPS
2165         select FB_DEFERRED_IO
2166         help
2167           This driver implements support for the E-Ink Metronome
2168           controller. The pre-release name for this device was 8track
2169           and could also have been called by some vendors as PVI-nnnn.
2170
2171 config FB_MB862XX
2172         tristate "Fujitsu MB862xx GDC support"
2173         depends on FB
2174         select FB_CFB_FILLRECT
2175         select FB_CFB_COPYAREA
2176         select FB_CFB_IMAGEBLIT
2177         ---help---
2178           Frame buffer driver for Fujitsu Carmine/Coral-P(A)/Lime controllers.
2179
2180 config FB_MB862XX_PCI_GDC
2181         bool "Carmine/Coral-P(A) GDC"
2182         depends on PCI && FB_MB862XX
2183         ---help---
2184           This enables framebuffer support for Fujitsu Carmine/Coral-P(A)
2185           PCI graphics controller devices.
2186
2187 config FB_MB862XX_LIME
2188         bool "Lime GDC"
2189         depends on FB_MB862XX
2190         depends on OF && !FB_MB862XX_PCI_GDC
2191         depends on PPC
2192         select FB_FOREIGN_ENDIAN
2193         select FB_LITTLE_ENDIAN
2194         ---help---
2195           Framebuffer support for Fujitsu Lime GDC on host CPU bus.
2196
2197 config FB_EP93XX
2198         tristate "EP93XX frame buffer support"
2199         depends on FB && ARCH_EP93XX
2200         select FB_CFB_FILLRECT
2201         select FB_CFB_COPYAREA
2202         select FB_CFB_IMAGEBLIT
2203         ---help---
2204           Framebuffer driver for the Cirrus Logic EP93XX series of processors.
2205           This driver is also available as a module. The module will be called
2206           ep93xx-fb.
2207
2208 config FB_PRE_INIT_FB
2209         bool "Don't reinitialize, use bootloader's GDC/Display configuration"
2210         depends on FB && FB_MB862XX_LIME
2211         ---help---
2212           Select this option if display contents should be inherited as set by
2213           the bootloader.
2214
2215 config FB_MSM
2216         tristate "MSM Framebuffer support"
2217         depends on FB && ARCH_MSM
2218         select FB_CFB_FILLRECT
2219         select FB_CFB_COPYAREA
2220         select FB_CFB_IMAGEBLIT
2221
2222 config FB_MX3
2223         tristate "MX3 Framebuffer support"
2224         depends on FB && MX3_IPU
2225         select FB_CFB_FILLRECT
2226         select FB_CFB_COPYAREA
2227         select FB_CFB_IMAGEBLIT
2228         default y
2229         help
2230           This is a framebuffer device for the i.MX31 LCD Controller. So
2231           far only synchronous displays are supported. If you plan to use
2232           an LCD display with your i.MX31 system, say Y here.
2233
2234 config FB_BROADSHEET
2235         tristate "E-Ink Broadsheet/Epson S1D13521 controller support"
2236         depends on FB
2237         select FB_SYS_FILLRECT
2238         select FB_SYS_COPYAREA
2239         select FB_SYS_IMAGEBLIT
2240         select FB_SYS_FOPS
2241         select FB_DEFERRED_IO
2242         help
2243           This driver implements support for the E-Ink Broadsheet
2244           controller. The release name for this device was Epson S1D13521
2245           and could also have been called by other names when coupled with
2246           a bridge adapter.
2247
2248 config FB_JZ4740
2249         tristate "JZ4740 LCD framebuffer support"
2250         depends on FB && MACH_JZ4740
2251         select FB_SYS_FILLRECT
2252         select FB_SYS_COPYAREA
2253         select FB_SYS_IMAGEBLIT
2254         help
2255           Framebuffer support for the JZ4740 SoC.
2256
2257 source "drivers/video/omap/Kconfig"
2258 source "drivers/video/omap2/Kconfig"
2259
2260 source "drivers/video/backlight/Kconfig"
2261 source "drivers/video/display/Kconfig"
2262
2263 if VT
2264         source "drivers/video/console/Kconfig"
2265 endif
2266
2267 if FB || SGI_NEWPORT_CONSOLE
2268         source "drivers/video/logo/Kconfig"
2269 endif
2270
2271 endmenu