drivers/video/Kconfig

   1 #
   2 # Video configuration
   3 #
   4
   5 menu "Graphics support"
   6         depends on HAS_IOMEM
   7
   8 source "drivers/char/agp/Kconfig"
   9
  10 source "drivers/gpu/drm/Kconfig"
  11
  12 config VGASTATE
  13        tristate
  14        default n
  15
  16 config VIDEO_OUTPUT_CONTROL
  17         tristate "Lowlevel video output switch controls"
  18         help
  19           This framework adds support for low-level control of the video
  20           output switch.
  21
  22 menuconfig FB
  23         tristate "Support for frame buffer devices"
  24         ---help---
  25           The frame buffer device provides an abstraction for the graphics
  26           hardware. It represents the frame buffer of some video hardware and
  27           allows application software to access the graphics hardware through
  28           a well-defined interface, so the software doesn't need to know
  29           anything about the low-level (hardware register) stuff.
  30
  31           Frame buffer devices work identically across the different
  32           architectures supported by Linux and make the implementation of
  33           application programs easier and more portable; at this point, an X
  34           server exists which uses the frame buffer device exclusively.
  35           On several non-X86 architectures, the frame buffer device is the
  36           only way to use the graphics hardware.
  37
  38           The device is accessed through special device nodes, usually located
  39           in the /dev directory, i.e. /dev/fb*.
  40
  41           You need an utility program called fbset to make full use of frame
  42           buffer devices. Please read <file:Documentation/fb/framebuffer.txt>
  43           and the Framebuffer-HOWTO at
  44           <http://www.munted.org.uk/programming/Framebuffer-HOWTO-1.2.html> for more
  45           information.
  46
  47           Say Y here and to the driver for your graphics board below if you
  48           are compiling a kernel for a non-x86 architecture.
  49
  50           If you are compiling for the x86 architecture, you can say Y if you
  51           want to play with it, but it is not essential. Please note that
  52           running graphical applications that directly touch the hardware
  53           (e.g. an accelerated X server) and that are not frame buffer
  54           device-aware may cause unexpected results. If unsure, say N.
  55
  56 config FIRMWARE_EDID
  57        bool "Enable firmware EDID"
  58        depends on FB
  59        default n
  60        ---help---
  61          This enables access to the EDID transferred from the firmware.
  62          On the i386, this is from the Video BIOS. Enable this if DDC/I2C
  63          transfers do not work for your driver and if you are using
  64          nvidiafb, i810fb or savagefb.
  65
  66          In general, choosing Y for this option is safe.  If you
  67          experience extremely long delays while booting before you get
  68          something on your display, try setting this to N.  Matrox cards in
  69          combination with certain motherboards and monitors are known to
  70          suffer from this problem.
  71
  72 config FB_DDC
  73        tristate
  74        depends on FB
  75        select I2C_ALGOBIT
  76        select I2C
  77        default n
  78
  79 config FB_BOOT_VESA_SUPPORT
  80         bool
  81         depends on FB
  82         default n
  83         ---help---
  84           If true, at least one selected framebuffer driver can take advantage
  85           of VESA video modes set at an early boot stage via the vga= parameter.
  86
  87 config FB_CFB_FILLRECT
  88         tristate
  89         depends on FB
  90         default n
  91         ---help---
  92           Include the cfb_fillrect function for generic software rectangle
  93           filling. This is used by drivers that don't provide their own
  94           (accelerated) version.
  95
  96 config FB_CFB_COPYAREA
  97         tristate
  98         depends on FB
  99         default n
 100         ---help---
 101           Include the cfb_copyarea function for generic software area copying.
 102           This is used by drivers that don't provide their own (accelerated)
 103           version.
 104
 105 config FB_CFB_IMAGEBLIT
 106         tristate
 107         depends on FB
 108         default n
 109         ---help---
 110           Include the cfb_imageblit function for generic software image
 111           blitting. This is used by drivers that don't provide their own
 112           (accelerated) version.
 113
 114 config FB_CFB_REV_PIXELS_IN_BYTE
 115         bool
 116         depends on FB
 117         default n
 118         ---help---
 119           Allow generic frame-buffer functions to work on displays with 1, 2
 120           and 4 bits per pixel depths which has opposite order of pixels in
 121           byte order to bytes in long order.
 122
 123 config FB_SYS_FILLRECT
 124         tristate
 125         depends on FB
 126         default n
 127         ---help---
 128           Include the sys_fillrect function for generic software rectangle
 129           filling. This is used by drivers that don't provide their own
 130           (accelerated) version and the framebuffer is in system RAM.
 131
 132 config FB_SYS_COPYAREA
 133         tristate
 134         depends on FB
 135         default n
 136         ---help---
 137           Include the sys_copyarea function for generic software area copying.
 138           This is used by drivers that don't provide their own (accelerated)
 139           version and the framebuffer is in system RAM.
 140
 141 config FB_SYS_IMAGEBLIT
 142         tristate
 143         depends on FB
 144         default n
 145         ---help---
 146           Include the sys_imageblit function for generic software image
 147           blitting. This is used by drivers that don't provide their own
 148           (accelerated) version and the framebuffer is in system RAM.
 149
 150 menuconfig FB_FOREIGN_ENDIAN
 151         bool "Framebuffer foreign endianness support"
 152         depends on FB
 153         ---help---
 154           This menu will let you enable support for the framebuffers with
 155           non-native endianness (e.g. Little-Endian framebuffer on a
 156           Big-Endian machine). Most probably you don't have such hardware,
 157           so it's safe to say "n" here.
 158
 159 choice
 160         prompt "Choice endianness support"
 161         depends on FB_FOREIGN_ENDIAN
 162
 163 config FB_BOTH_ENDIAN
 164         bool "Support for Big- and Little-Endian framebuffers"
 165
 166 config FB_BIG_ENDIAN
 167         bool "Support for Big-Endian framebuffers only"
 168
 169 config FB_LITTLE_ENDIAN
 170         bool "Support for Little-Endian framebuffers only"
 171
 172 endchoice
 173
 174 config FB_SYS_FOPS
 175        tristate
 176        depends on FB
 177        default n
 178
 179 config FB_DEFERRED_IO
 180         bool
 181         depends on FB
 182
 183 config FB_HECUBA
 184         tristate
 185         depends on FB
 186         depends on FB_DEFERRED_IO
 187
 188 config FB_SVGALIB
 189         tristate
 190         depends on FB
 191         default n
 192         ---help---
 193           Common utility functions useful to fbdev drivers of VGA-based
 194           cards.
 195
 196 config FB_MACMODES
 197        tristate
 198        depends on FB
 199        default n
 200
 201 config FB_BACKLIGHT
 202         bool
 203         depends on FB
 204         select BACKLIGHT_LCD_SUPPORT
 205         select BACKLIGHT_CLASS_DEVICE
 206         default n
 207
 208 config FB_MODE_HELPERS
 209         bool "Enable Video Mode Handling Helpers"
 210         depends on FB
 211         default n
 212         ---help---
 213           This enables functions for handling video modes using the
 214           Generalized Timing Formula and the EDID parser. A few drivers rely
 215           on this feature such as the radeonfb, rivafb, and the i810fb. If
 216           your driver does not take advantage of this feature, choosing Y will
 217           just increase the kernel size by about 5K.
 218
 219 config FB_TILEBLITTING
 220        bool "Enable Tile Blitting Support"
 221        depends on FB
 222        default n
 223        ---help---
 224          This enables tile blitting.  Tile blitting is a drawing technique
 225          where the screen is divided into rectangular sections (tiles), whereas
 226          the standard blitting divides the screen into pixels. Because the
 227          default drawing element is a tile, drawing functions will be passed
 228          parameters in terms of number of tiles instead of number of pixels.
 229          For example, to draw a single character, instead of using bitmaps,
 230          an index to an array of bitmaps will be used.  To clear or move a
 231          rectangular section of a screen, the rectangle will be described in
 232          terms of number of tiles in the x- and y-axis.
 233
 234          This is particularly important to one driver, matroxfb.  If
 235          unsure, say N.
 236
 237 comment "Frame buffer hardware drivers"
 238         depends on FB
 239
 240 config FB_CIRRUS
 241         tristate "Cirrus Logic support"
 242         depends on FB && (ZORRO || PCI)
 243         select FB_CFB_FILLRECT
 244         select FB_CFB_COPYAREA
 245         select FB_CFB_IMAGEBLIT
 246         ---help---
 247           This enables support for Cirrus Logic GD542x/543x based boards on
 248           Amiga: SD64, Piccolo, Picasso II/II+, Picasso IV, or EGS Spectrum.
 249
 250           If you have a PCI-based system, this enables support for these
 251           chips: GD-543x, GD-544x, GD-5480.
 252
 253           Please read the file <file:Documentation/fb/cirrusfb.txt>.
 254
 255           Say N unless you have such a graphics board or plan to get one
 256           before you next recompile the kernel.
 257
 258 config FB_PM2
 259         tristate "Permedia2 support"
 260         depends on FB && ((AMIGA && BROKEN) || PCI)
 261         select FB_CFB_FILLRECT
 262         select FB_CFB_COPYAREA
 263         select FB_CFB_IMAGEBLIT
 264         help
 265           This is the frame buffer device driver for cards based on
 266           the 3D Labs Permedia, Permedia 2 and Permedia 2V chips.
 267           The driver was tested on the following cards:
 268                 Diamond FireGL 1000 PRO AGP
 269                 ELSA Gloria Synergy PCI
 270                 Appian Jeronimo PRO (both heads) PCI
 271                 3DLabs Oxygen ACX aka EONtronics Picasso P2 PCI
 272                 Techsource Raptor GFX-8P (aka Sun PGX-32) on SPARC
 273                 ASK Graphic Blaster Exxtreme AGP
 274
 275           To compile this driver as a module, choose M here: the
 276           module will be called pm2fb.
 277
 278 config FB_PM2_FIFO_DISCONNECT
 279         bool "enable FIFO disconnect feature"
 280         depends on FB_PM2 && PCI
 281         help
 282           Support the Permedia2 FIFO disconnect feature.
 283
 284 config FB_ARMCLCD
 285         tristate "ARM PrimeCell PL110 support"
 286         depends on FB && ARM && ARM_AMBA
 287         select FB_CFB_FILLRECT
 288         select FB_CFB_COPYAREA
 289         select FB_CFB_IMAGEBLIT
 290         help
 291           This framebuffer device driver is for the ARM PrimeCell PL110
 292           Colour LCD controller.  ARM PrimeCells provide the building
 293           blocks for System on a Chip devices.
 294
 295           If you want to compile this as a module (=code which can be
 296           inserted into and removed from the running kernel), say M
 297           here and read <file:Documentation/kbuild/modules.txt>.  The module
 298           will be called amba-clcd.
 299
 300 choice
 301
 302         depends on FB_ARMCLCD && (ARCH_LH7A40X || ARCH_LH7952X)
 303         prompt "LCD Panel"
 304         default FB_ARMCLCD_SHARP_LQ035Q7DB02
 305
 306 config FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT
 307         bool "LogicPD LCD 3.5\" QVGA w/HRTFT IC"
 308         help
 309           This is an implementation of the Sharp LQ035Q7DB02, a 3.5"
 310           color QVGA, HRTFT panel.  The LogicPD device includes
 311           an integrated HRTFT controller IC.
 312           The native resolution is 240x320.
 313
 314 config FB_ARMCLCD_SHARP_LQ057Q3DC02
 315         bool "LogicPD LCD 5.7\" QVGA"
 316         help
 317           This is an implementation of the Sharp LQ057Q3DC02, a 5.7"
 318           color QVGA, TFT panel.  The LogicPD device includes an
 319           The native resolution is 320x240.
 320
 321 config FB_ARMCLCD_SHARP_LQ64D343
 322         bool "LogicPD LCD 6.4\" VGA"
 323         help
 324           This is an implementation of the Sharp LQ64D343, a 6.4"
 325           color VGA, TFT panel.  The LogicPD device includes an
 326           The native resolution is 640x480.
 327
 328 config FB_ARMCLCD_SHARP_LQ10D368
 329         bool "LogicPD LCD 10.4\" VGA"
 330         help
 331           This is an implementation of the Sharp LQ10D368, a 10.4"
 332           color VGA, TFT panel.  The LogicPD device includes an
 333           The native resolution is 640x480.
 334
 335
 336 config FB_ARMCLCD_SHARP_LQ121S1DG41
 337         bool "LogicPD LCD 12.1\" SVGA"
 338         help
 339           This is an implementation of the Sharp LQ121S1DG41, a 12.1"
 340           color SVGA, TFT panel.  The LogicPD device includes an
 341           The native resolution is 800x600.
 342
 343           This panel requires a clock rate may be an integer fraction
 344           of the base LCDCLK frequency.  The driver will select the
 345           highest frequency available that is lower than the maximum
 346           allowed.  The panel may flicker if the clock rate is
 347           slower than the recommended minimum.
 348
 349 config FB_ARMCLCD_AUO_A070VW01_WIDE
 350         bool "AU Optronics A070VW01 LCD 7.0\" WIDE"
 351         help
 352           This is an implementation of the AU Optronics, a 7.0"
 353           WIDE Color.  The native resolution is 234x480.
 354
 355 config FB_ARMCLCD_HITACHI
 356         bool "Hitachi Wide Screen 800x480"
 357         help
 358           This is an implementation of the Hitachi 800x480.
 359
 360 endchoice
 361
 362
 363 config FB_ACORN
 364         bool "Acorn VIDC support"
 365         depends on (FB = y) && ARM && ARCH_ACORN
 366         select FB_CFB_FILLRECT
 367         select FB_CFB_COPYAREA
 368         select FB_CFB_IMAGEBLIT
 369         help
 370           This is the frame buffer device driver for the Acorn VIDC graphics
 371           hardware found in Acorn RISC PCs and other ARM-based machines.  If
 372           unsure, say N.
 373
 374 config FB_CLPS711X
 375         bool "CLPS711X LCD support"
 376         depends on (FB = y) && ARM && ARCH_CLPS711X
 377         select FB_CFB_FILLRECT
 378         select FB_CFB_COPYAREA
 379         select FB_CFB_IMAGEBLIT
 380         help
 381           Say Y to enable the Framebuffer driver for the CLPS7111 and
 382           EP7212 processors.
 383
 384 config FB_SA1100
 385         bool "SA-1100 LCD support"
 386         depends on (FB = y) && ARM && ARCH_SA1100
 387         select FB_CFB_FILLRECT
 388         select FB_CFB_COPYAREA
 389         select FB_CFB_IMAGEBLIT
 390         help
 391           This is a framebuffer device for the SA-1100 LCD Controller.
 392           See <http://www.linux-fbdev.org/> for information on framebuffer
 393           devices.
 394
 395           If you plan to use the LCD display with your SA-1100 system, say
 396           Y here.
 397
 398 config FB_IMX
 399         tristate "Motorola i.MX LCD support"
 400         depends on FB && (ARCH_MX1 || ARCH_MX2)
 401         select FB_CFB_FILLRECT
 402         select FB_CFB_COPYAREA
 403         select FB_CFB_IMAGEBLIT
 404
 405 config FB_CYBER2000
 406         tristate "CyberPro 2000/2010/5000 support"
 407         depends on FB && PCI && (BROKEN || !SPARC64)
 408         select FB_CFB_FILLRECT
 409         select FB_CFB_COPYAREA
 410         select FB_CFB_IMAGEBLIT
 411         help
 412           This enables support for the Integraphics CyberPro 20x0 and 5000
 413           VGA chips used in the Rebel.com Netwinder and other machines.
 414           Say Y if you have a NetWinder or a graphics card containing this
 415           device, otherwise say N.
 416
 417 config FB_APOLLO
 418         bool
 419         depends on (FB = y) && APOLLO
 420         default y
 421         select FB_CFB_FILLRECT
 422         select FB_CFB_IMAGEBLIT
 423
 424 config FB_Q40
 425         bool
 426         depends on (FB = y) && Q40
 427         default y
 428         select FB_CFB_FILLRECT
 429         select FB_CFB_COPYAREA
 430         select FB_CFB_IMAGEBLIT
 431
 432 config FB_AMIGA
 433         tristate "Amiga native chipset support"
 434         depends on FB && AMIGA
 435         help
 436           This is the frame buffer device driver for the builtin graphics
 437           chipset found in Amigas.
 438
 439           To compile this driver as a module, choose M here: the
 440           module will be called amifb.
 441
 442 config FB_AMIGA_OCS
 443         bool "Amiga OCS chipset support"
 444         depends on FB_AMIGA
 445         help
 446           This enables support for the original Agnus and Denise video chips,
 447           found in the Amiga 1000 and most A500's and A2000's. If you intend
 448           to run Linux on any of these systems, say Y; otherwise say N.
 449
 450 config FB_AMIGA_ECS
 451         bool "Amiga ECS chipset support"
 452         depends on FB_AMIGA
 453         help
 454           This enables support for the Enhanced Chip Set, found in later
 455           A500's, later A2000's, the A600, the A3000, the A3000T and CDTV. If
 456           you intend to run Linux on any of these systems, say Y; otherwise
 457           say N.
 458
 459 config FB_AMIGA_AGA
 460         bool "Amiga AGA chipset support"
 461         depends on FB_AMIGA
 462         help
 463           This enables support for the Advanced Graphics Architecture (also
 464           known as the AGA or AA) Chip Set, found in the A1200, A4000, A4000T
 465           and CD32. If you intend to run Linux on any of these systems, say Y;
 466           otherwise say N.
 467
 468 config FB_FM2
 469         bool "Amiga FrameMaster II/Rainbow II support"
 470         depends on (FB = y) && ZORRO
 471         select FB_CFB_FILLRECT
 472         select FB_CFB_COPYAREA
 473         select FB_CFB_IMAGEBLIT
 474         help
 475           This is the frame buffer device driver for the Amiga FrameMaster
 476           card from BSC (exhibited 1992 but not shipped as a CBM product).
 477
 478 config FB_ARC
 479         tristate "Arc Monochrome LCD board support"
 480         depends on FB && X86
 481         select FB_SYS_FILLRECT
 482         select FB_SYS_COPYAREA
 483         select FB_SYS_IMAGEBLIT
 484         select FB_SYS_FOPS
 485         help
 486           This enables support for the Arc Monochrome LCD board. The board
 487           is based on the KS-108 lcd controller and is typically a matrix
 488           of 2*n chips. This driver was tested with a 128x64 panel. This
 489           driver supports it for use with x86 SBCs through a 16 bit GPIO
 490           interface (8 bit data, 8 bit control). If you anticipate using
 491           this driver, say Y or M; otherwise say N. You must specify the
 492           GPIO IO address to be used for setting control and data.
 493
 494 config FB_ATARI
 495         bool "Atari native chipset support"
 496         depends on (FB = y) && ATARI
 497         select FB_CFB_FILLRECT
 498         select FB_CFB_COPYAREA
 499         select FB_CFB_IMAGEBLIT
 500         help
 501           This is the frame buffer device driver for the builtin graphics
 502           chipset found in Ataris.
 503
 504 config FB_OF
 505         bool "Open Firmware frame buffer device support"
 506         depends on (FB = y) && (PPC64 || PPC_OF) && (!PPC_PSERIES || PCI)
 507         select FB_CFB_FILLRECT
 508         select FB_CFB_COPYAREA
 509         select FB_CFB_IMAGEBLIT
 510         select FB_MACMODES
 511         help
 512           Say Y if you want support with Open Firmware for your graphics
 513           board.
 514
 515 config FB_CONTROL
 516         bool "Apple \"control\" display support"
 517         depends on (FB = y) && PPC_PMAC && PPC32
 518         select FB_CFB_FILLRECT
 519         select FB_CFB_COPYAREA
 520         select FB_CFB_IMAGEBLIT
 521         select FB_MACMODES
 522         help
 523           This driver supports a frame buffer for the graphics adapter in the
 524           Power Macintosh 7300 and others.
 525
 526 config FB_PLATINUM
 527         bool "Apple \"platinum\" display support"
 528         depends on (FB = y) && PPC_PMAC && PPC32
 529         select FB_CFB_FILLRECT
 530         select FB_CFB_COPYAREA
 531         select FB_CFB_IMAGEBLIT
 532         select FB_MACMODES
 533         help
 534           This driver supports a frame buffer for the "platinum" graphics
 535           adapter in some Power Macintoshes.
 536
 537 config FB_VALKYRIE
 538         bool "Apple \"valkyrie\" display support"
 539         depends on (FB = y) && (MAC || (PPC_PMAC && PPC32))
 540         select FB_CFB_FILLRECT
 541         select FB_CFB_COPYAREA
 542         select FB_CFB_IMAGEBLIT
 543         select FB_MACMODES
 544         help
 545           This driver supports a frame buffer for the "valkyrie" graphics
 546           adapter in some Power Macintoshes.
 547
 548 config FB_CT65550
 549         bool "Chips 65550 display support"
 550         depends on (FB = y) && PPC32 && PCI
 551         select FB_CFB_FILLRECT
 552         select FB_CFB_COPYAREA
 553         select FB_CFB_IMAGEBLIT
 554         help
 555           This is the frame buffer device driver for the Chips & Technologies
 556           65550 graphics chip in PowerBooks.
 557
 558 config FB_ASILIANT
 559         bool "Asiliant (Chips) 69000 display support"
 560         depends on (FB = y) && PCI
 561         select FB_CFB_FILLRECT
 562         select FB_CFB_COPYAREA
 563         select FB_CFB_IMAGEBLIT
 564         help
 565           This is the frame buffer device driver for the Asiliant 69030 chipset
 566
 567 config FB_IMSTT
 568         bool "IMS Twin Turbo display support"
 569         depends on (FB = y) && PCI
 570         select FB_CFB_IMAGEBLIT
 571         select FB_MACMODES if PPC
 572         help
 573           The IMS Twin Turbo is a PCI-based frame buffer card bundled with
 574           many Macintosh and compatible computers.
 575
 576 config FB_VGA16
 577         tristate "VGA 16-color graphics support"
 578         depends on FB && (X86 || PPC)
 579         select FB_CFB_FILLRECT
 580         select FB_CFB_COPYAREA
 581         select FB_CFB_IMAGEBLIT
 582         select VGASTATE
 583         select FONT_8x16 if FRAMEBUFFER_CONSOLE
 584         help
 585           This is the frame buffer device driver for VGA 16 color graphic
 586           cards. Say Y if you have such a card.
 587
 588           To compile this driver as a module, choose M here: the
 589           module will be called vga16fb.
 590
 591 config FB_BF54X_LQ043
 592         tristate "SHARP LQ043 TFT LCD (BF548 EZKIT)"
 593         depends on FB && (BF54x) && !BF542
 594         select FB_CFB_FILLRECT
 595         select FB_CFB_COPYAREA
 596         select FB_CFB_IMAGEBLIT
 597         help
 598          This is the framebuffer device driver for a SHARP LQ043T1DG01 TFT LCD
 599
 600 config FB_BFIN_T350MCQB
 601         tristate "Varitronix COG-T350MCQB TFT LCD display (BF527 EZKIT)"
 602         depends on FB && BLACKFIN
 603         select BFIN_GPTIMERS
 604         select FB_CFB_FILLRECT
 605         select FB_CFB_COPYAREA
 606         select FB_CFB_IMAGEBLIT
 607         help
 608          This is the framebuffer device driver for a Varitronix VL-PS-COG-T350MCQB-01 display TFT LCD
 609          This display is a QVGA 320x240 24-bit RGB display interfaced by an 8-bit wide PPI
 610          It uses PPI[0..7] PPI_FS1, PPI_FS2 and PPI_CLK.
 611
 612
 613 config FB_STI
 614         tristate "HP STI frame buffer device support"
 615         depends on FB && PARISC
 616         select FB_CFB_FILLRECT
 617         select FB_CFB_COPYAREA
 618         select FB_CFB_IMAGEBLIT
 619         default y
 620         ---help---
 621           STI refers to the HP "Standard Text Interface" which is a set of
 622           BIOS routines contained in a ROM chip in HP PA-RISC based machines.
 623           Enabling this option will implement the linux framebuffer device
 624           using calls to the STI BIOS routines for initialisation.
 625
 626           If you enable this option, you will get a planar framebuffer device
 627           /dev/fb which will work on the most common HP graphic cards of the
 628           NGLE family, including the artist chips (in the 7xx and Bxxx series),
 629           HCRX, HCRX24, CRX, CRX24 and VisEG series.
 630
 631           It is safe to enable this option, so you should probably say "Y".
 632
 633 config FB_MAC
 634         bool "Generic Macintosh display support"
 635         depends on (FB = y) && MAC
 636         select FB_CFB_FILLRECT
 637         select FB_CFB_COPYAREA
 638         select FB_CFB_IMAGEBLIT
 639         select FB_MACMODES
 640
 641 config FB_HP300
 642         bool
 643         depends on (FB = y) && DIO
 644         select FB_CFB_IMAGEBLIT
 645         default y
 646
 647 config FB_TGA
 648         tristate "TGA/SFB+ framebuffer support"
 649         depends on FB && (ALPHA || TC)
 650         select FB_CFB_FILLRECT
 651         select FB_CFB_COPYAREA
 652         select FB_CFB_IMAGEBLIT
 653         select BITREVERSE
 654         ---help---
 655           This is the frame buffer device driver for generic TGA and SFB+
 656           graphic cards.  These include DEC ZLXp-E1, -E2 and -E3 PCI cards,
 657           also known as PBXGA-A, -B and -C, and DEC ZLX-E1, -E2 and -E3
 658           TURBOchannel cards, also known as PMAGD-A, -B and -C.
 659
 660           Due to hardware limitations ZLX-E2 and E3 cards are not supported
 661           for DECstation 5000/200 systems.  Additionally due to firmware
 662           limitations these cards may cause troubles with booting DECstation
 663           5000/240 and /260 systems, but are fully supported under Linux if
 664           you manage to get it going. ;-)
 665
 666           Say Y if you have one of those.
 667
 668 config FB_UVESA
 669         tristate "Userspace VESA VGA graphics support"
 670         depends on FB && CONNECTOR
 671         select FB_CFB_FILLRECT
 672         select FB_CFB_COPYAREA
 673         select FB_CFB_IMAGEBLIT
 674         select FB_MODE_HELPERS
 675         help
 676           This is the frame buffer driver for generic VBE 2.0 compliant
 677           graphic cards. It can also take advantage of VBE 3.0 features,
 678           such as refresh rate adjustment.
 679
 680           This driver generally provides more features than vesafb but
 681           requires a userspace helper application called 'v86d'. See
 682           <file:Documentation/fb/uvesafb.txt> for more information.
 683
 684           If unsure, say N.
 685
 686 config FB_VESA
 687         bool "VESA VGA graphics support"
 688         depends on (FB = y) && X86
 689         select FB_CFB_FILLRECT
 690         select FB_CFB_COPYAREA
 691         select FB_CFB_IMAGEBLIT
 692         select FB_BOOT_VESA_SUPPORT
 693         help
 694           This is the frame buffer device driver for generic VESA 2.0
 695           compliant graphic cards. The older VESA 1.2 cards are not supported.
 696           You will get a boot time penguin logo at no additional cost. Please
 697           read <file:Documentation/fb/vesafb.txt>. If unsure, say Y.
 698
 699 config FB_EFI
 700         bool "EFI-based Framebuffer Support"
 701         depends on (FB = y) && X86 && EFI
 702         select FB_CFB_FILLRECT
 703         select FB_CFB_COPYAREA
 704         select FB_CFB_IMAGEBLIT
 705         help
 706           This is the EFI frame buffer device driver. If the firmware on
 707           your platform is EFI 1.10 or UEFI 2.0, select Y to add support for
 708           using the EFI framebuffer as your console.
 709
 710 config FB_N411
 711        tristate "N411 Apollo/Hecuba devkit support"
 712        depends on FB && X86 && MMU
 713        select FB_SYS_FILLRECT
 714        select FB_SYS_COPYAREA
 715        select FB_SYS_IMAGEBLIT
 716        select FB_SYS_FOPS
 717        select FB_DEFERRED_IO
 718        select FB_HECUBA
 719        help
 720          This enables support for the Apollo display controller in its
 721          Hecuba form using the n411 devkit.
 722
 723 config FB_HGA
 724         tristate "Hercules mono graphics support"
 725         depends on FB && X86
 726         select FB_CFB_FILLRECT
 727         select FB_CFB_COPYAREA
 728         select FB_CFB_IMAGEBLIT
 729         help
 730           Say Y here if you have a Hercules mono graphics card.
 731
 732           To compile this driver as a module, choose M here: the
 733           module will be called hgafb.
 734
 735           As this card technology is 15 years old, most people will answer N
 736           here.
 737
 738 config FB_HGA_ACCEL
 739         bool "Hercules mono Acceleration functions (EXPERIMENTAL)"
 740         depends on FB_HGA && EXPERIMENTAL
 741         ---help---
 742         This will compile the Hercules mono graphics with
 743         acceleration functions.
 744
 745 config FB_SGIVW
 746         tristate "SGI Visual Workstation framebuffer support"
 747         depends on FB && X86_VISWS
 748         select FB_CFB_FILLRECT
 749         select FB_CFB_COPYAREA
 750         select FB_CFB_IMAGEBLIT
 751         help
 752           SGI Visual Workstation support for framebuffer graphics.
 753
 754 config FB_GBE
 755         bool "SGI Graphics Backend frame buffer support"
 756         depends on (FB = y) && (SGI_IP32 || X86_VISWS)
 757         select FB_CFB_FILLRECT
 758         select FB_CFB_COPYAREA
 759         select FB_CFB_IMAGEBLIT
 760         help
 761           This is the frame buffer device driver for SGI Graphics Backend.
 762           This chip is used in SGI O2 and Visual Workstation 320/540.
 763
 764 config FB_GBE_MEM
 765         int "Video memory size in MB"
 766         depends on FB_GBE
 767         default 4
 768         help
 769           This is the amount of memory reserved for the framebuffer,
 770           which can be any value between 1MB and 8MB.
 771
 772 config FB_SBUS
 773         bool "SBUS and UPA framebuffers"
 774         depends on (FB = y) && SPARC
 775         help
 776           Say Y if you want support for SBUS or UPA based frame buffer device.
 777
 778 config FB_BW2
 779         bool "BWtwo support"
 780         depends on (FB = y) && (SPARC && FB_SBUS)
 781         select FB_CFB_FILLRECT
 782         select FB_CFB_COPYAREA
 783         select FB_CFB_IMAGEBLIT
 784         help
 785           This is the frame buffer device driver for the BWtwo frame buffer.
 786
 787 config FB_CG3
 788         bool "CGthree support"
 789         depends on (FB = y) && (SPARC && FB_SBUS)
 790         select FB_CFB_FILLRECT
 791         select FB_CFB_COPYAREA
 792         select FB_CFB_IMAGEBLIT
 793         help
 794           This is the frame buffer device driver for the CGthree frame buffer.
 795
 796 config FB_CG6
 797         bool "CGsix (GX,TurboGX) support"
 798         depends on (FB = y) && (SPARC && FB_SBUS)
 799         select FB_CFB_COPYAREA
 800         select FB_CFB_IMAGEBLIT
 801         help
 802           This is the frame buffer device driver for the CGsix (GX, TurboGX)
 803           frame buffer.
 804
 805 config FB_FFB
 806         bool "Creator/Creator3D/Elite3D support"
 807         depends on FB_SBUS && SPARC64
 808         select FB_CFB_COPYAREA
 809         select FB_CFB_IMAGEBLIT
 810         help
 811           This is the frame buffer device driver for the Creator, Creator3D,
 812           and Elite3D graphics boards.
 813
 814 config FB_TCX
 815         bool "TCX (SS4/SS5 only) support"
 816         depends on FB_SBUS
 817         select FB_CFB_FILLRECT
 818         select FB_CFB_COPYAREA
 819         select FB_CFB_IMAGEBLIT
 820         help
 821           This is the frame buffer device driver for the TCX 24/8bit frame
 822           buffer.
 823
 824 config FB_CG14
 825         bool "CGfourteen (SX) support"
 826         depends on FB_SBUS
 827         select FB_CFB_FILLRECT
 828         select FB_CFB_COPYAREA
 829         select FB_CFB_IMAGEBLIT
 830         help
 831           This is the frame buffer device driver for the CGfourteen frame
 832           buffer on Desktop SPARCsystems with the SX graphics option.
 833
 834 config FB_P9100
 835         bool "P9100 (Sparcbook 3 only) support"
 836         depends on FB_SBUS
 837         select FB_CFB_FILLRECT
 838         select FB_CFB_COPYAREA
 839         select FB_CFB_IMAGEBLIT
 840         help
 841           This is the frame buffer device driver for the P9100 card
 842           supported on Sparcbook 3 machines.
 843
 844 config FB_LEO
 845         bool "Leo (ZX) support"
 846         depends on FB_SBUS
 847         select FB_CFB_FILLRECT
 848         select FB_CFB_COPYAREA
 849         select FB_CFB_IMAGEBLIT
 850         help
 851           This is the frame buffer device driver for the SBUS-based Sun ZX
 852           (leo) frame buffer cards.
 853
 854 config FB_IGA
 855         bool "IGA 168x display support"
 856         depends on (FB = y) && SPARC32
 857         select FB_CFB_FILLRECT
 858         select FB_CFB_COPYAREA
 859         select FB_CFB_IMAGEBLIT
 860         help
 861           This is the framebuffer device for the INTERGRAPHICS 1680 and
 862           successor frame buffer cards.
 863
 864 config FB_XVR500
 865         bool "Sun XVR-500 3DLABS Wildcat support"
 866         depends on (FB = y) && PCI && SPARC64
 867         select FB_CFB_FILLRECT
 868         select FB_CFB_COPYAREA
 869         select FB_CFB_IMAGEBLIT
 870         help
 871           This is the framebuffer device for the Sun XVR-500 and similar
 872           graphics cards based upon the 3DLABS Wildcat chipset.  The driver
 873           only works on sparc64 systems where the system firmware has
 874           mostly initialized the card already.  It is treated as a
 875           completely dumb framebuffer device.
 876
 877 config FB_XVR2500
 878         bool "Sun XVR-2500 3DLABS Wildcat support"
 879         depends on (FB = y) && PCI && SPARC64
 880         select FB_CFB_FILLRECT
 881         select FB_CFB_COPYAREA
 882         select FB_CFB_IMAGEBLIT
 883         help
 884           This is the framebuffer device for the Sun XVR-2500 and similar
 885           graphics cards based upon the 3DLABS Wildcat chipset.  The driver
 886           only works on sparc64 systems where the system firmware has
 887           mostly initialized the card already.  It is treated as a
 888           completely dumb framebuffer device.
 889
 890 config FB_PVR2
 891         tristate "NEC PowerVR 2 display support"
 892         depends on FB && SH_DREAMCAST
 893         select FB_CFB_FILLRECT
 894         select FB_CFB_COPYAREA
 895         select FB_CFB_IMAGEBLIT
 896         ---help---
 897           Say Y here if you have a PowerVR 2 card in your box.  If you plan to
 898           run linux on your Dreamcast, you will have to say Y here.
 899           This driver may or may not work on other PowerVR 2 cards, but is
 900           totally untested.  Use at your own risk.  If unsure, say N.
 901
 902           To compile this driver as a module, choose M here: the
 903           module will be called pvr2fb.
 904
 905           You can pass several parameters to the driver at boot time or at
 906           module load time.  The parameters look like "video=pvr2:XXX", where
 907           the meaning of XXX can be found at the end of the main source file
 908           (<file:drivers/video/pvr2fb.c>). Please see the file
 909           <file:Documentation/fb/pvr2fb.txt>.
 910
 911 config FB_EPSON1355
 912         bool "Epson 1355 framebuffer support"
 913         depends on (FB = y) && ARCH_CEIVA
 914         select FB_CFB_FILLRECT
 915         select FB_CFB_COPYAREA
 916         select FB_CFB_IMAGEBLIT
 917         help
 918           Build in support for the SED1355 Epson Research Embedded RAMDAC
 919           LCD/CRT Controller (since redesignated as the S1D13505) as a
 920           framebuffer.  Product specs at
 921           <http://www.erd.epson.com/vdc/html/products.htm>.
 922
 923 config FB_S1D13XXX
 924         tristate "Epson S1D13XXX framebuffer support"
 925         depends on FB
 926         select FB_CFB_FILLRECT
 927         select FB_CFB_COPYAREA
 928         select FB_CFB_IMAGEBLIT
 929         help
 930           Support for S1D13XXX framebuffer device family (currently only
 931           working with S1D13806). Product specs at
 932           <http://www.erd.epson.com/vdc/html/legacy_13xxx.htm>
 933
 934 config FB_ATMEL
 935         tristate "AT91/AT32 LCD Controller support"
 936         depends on FB && (ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9 || AVR32)
 937         select FB_CFB_FILLRECT
 938         select FB_CFB_COPYAREA
 939         select FB_CFB_IMAGEBLIT
 940         help
 941           This enables support for the AT91/AT32 LCD Controller.
 942
 943 config FB_INTSRAM
 944         bool "Frame Buffer in internal SRAM"
 945         depends on FB_ATMEL && ARCH_AT91SAM9261
 946         help
 947           Say Y if you want to map Frame Buffer in internal SRAM. Say N if you want
 948           to let frame buffer in external SDRAM.
 949
 950 config FB_ATMEL_STN
 951         bool "Use a STN display with AT91/AT32 LCD Controller"
 952         depends on FB_ATMEL && MACH_AT91SAM9261EK
 953         default n
 954         help
 955           Say Y if you want to connect a STN LCD display to the AT91/AT32 LCD
 956           Controller. Say N if you want to connect a TFT.
 957
 958           If unsure, say N.
 959
 960 config FB_NVIDIA
 961         tristate "nVidia Framebuffer Support"
 962         depends on FB && PCI
 963         select FB_BACKLIGHT if FB_NVIDIA_BACKLIGHT
 964         select FB_MODE_HELPERS
 965         select FB_CFB_FILLRECT
 966         select FB_CFB_COPYAREA
 967         select FB_CFB_IMAGEBLIT
 968         select BITREVERSE
 969         select VGASTATE
 970         help
 971           This driver supports graphics boards with the nVidia chips, TNT
 972           and newer. For very old chipsets, such as the RIVA128, then use
 973           the rivafb.
 974           Say Y if you have such a graphics board.
 975
 976           To compile this driver as a module, choose M here: the
 977           module will be called nvidiafb.
 978
 979 config FB_NVIDIA_I2C
 980        bool "Enable DDC Support"
 981        depends on FB_NVIDIA
 982        select FB_DDC
 983        help
 984           This enables I2C support for nVidia Chipsets.  This is used
 985           only for getting EDID information from the attached display
 986           allowing for robust video mode handling and switching.
 987
 988           Because fbdev-2.6 requires that drivers must be able to
 989           independently validate video mode parameters, you should say Y
 990           here.
 991
 992 config FB_NVIDIA_DEBUG
 993         bool "Lots of debug output"
 994         depends on FB_NVIDIA
 995         default n
 996         help
 997           Say Y here if you want the nVidia driver to output all sorts
 998           of debugging information to provide to the maintainer when
 999           something goes wrong.
1000
1001 config FB_NVIDIA_BACKLIGHT
1002         bool "Support for backlight control"
1003         depends on FB_NVIDIA
1004         default y
1005         help
1006           Say Y here if you want to control the backlight of your display.
1007
1008 config FB_RIVA
1009         tristate "nVidia Riva support"
1010         depends on FB && PCI
1011         select FB_BACKLIGHT if FB_RIVA_BACKLIGHT
1012         select FB_MODE_HELPERS
1013         select FB_CFB_FILLRECT
1014         select FB_CFB_COPYAREA
1015         select FB_CFB_IMAGEBLIT
1016         select BITREVERSE
1017         select VGASTATE
1018         help
1019           This driver supports graphics boards with the nVidia Riva/Geforce
1020           chips.
1021           Say Y if you have such a graphics board.
1022
1023           To compile this driver as a module, choose M here: the
1024           module will be called rivafb.
1025
1026 config FB_RIVA_I2C
1027        bool "Enable DDC Support"
1028        depends on FB_RIVA
1029        select FB_DDC
1030        help
1031           This enables I2C support for nVidia Chipsets.  This is used
1032           only for getting EDID information from the attached display
1033           allowing for robust video mode handling and switching.
1034
1035           Because fbdev-2.6 requires that drivers must be able to
1036           independently validate video mode parameters, you should say Y
1037           here.
1038
1039 config FB_RIVA_DEBUG
1040         bool "Lots of debug output"
1041         depends on FB_RIVA
1042         default n
1043         help
1044           Say Y here if you want the Riva driver to output all sorts
1045           of debugging information to provide to the maintainer when
1046           something goes wrong.
1047
1048 config FB_RIVA_BACKLIGHT
1049         bool "Support for backlight control"
1050         depends on FB_RIVA
1051         default y
1052         help
1053           Say Y here if you want to control the backlight of your display.
1054
1055 config FB_I810
1056         tristate "Intel 810/815 support (EXPERIMENTAL)"
1057         depends on EXPERIMENTAL && FB && PCI && X86_32 && AGP_INTEL
1058         select FB_MODE_HELPERS
1059         select FB_CFB_FILLRECT
1060         select FB_CFB_COPYAREA
1061         select FB_CFB_IMAGEBLIT
1062         select VGASTATE
1063         help
1064           This driver supports the on-board graphics built in to the Intel 810
1065           and 815 chipsets.  Say Y if you have and plan to use such a board.
1066
1067           To compile this driver as a module, choose M here: the
1068           module will be called i810fb.
1069
1070           For more information, please read
1071           <file:Documentation/fb/intel810.txt>
1072
1073 config FB_I810_GTF
1074         bool "use VESA Generalized Timing Formula"
1075         depends on FB_I810
1076         help
1077           If you say Y, then the VESA standard, Generalized Timing Formula
1078           or GTF, will be used to calculate the required video timing values
1079           per video mode.  Since the GTF allows nondiscrete timings
1080           (nondiscrete being a range of values as opposed to discrete being a
1081           set of values), you'll be able to use any combination of horizontal
1082           and vertical resolutions, and vertical refresh rates without having
1083           to specify your own timing parameters.  This is especially useful
1084           to maximize the performance of an aging display, or if you just
1085           have a display with nonstandard dimensions. A VESA compliant
1086           monitor is recommended, but can still work with non-compliant ones.
1087           If you need or want this, then select this option. The timings may
1088           not be compliant with Intel's recommended values. Use at your own
1089           risk.
1090
1091           If you say N, the driver will revert to discrete video timings
1092           using a set recommended by Intel in their documentation.
1093
1094           If unsure, say N.
1095
1096 config FB_I810_I2C
1097         bool "Enable DDC Support"
1098         depends on FB_I810 && FB_I810_GTF
1099         select FB_DDC
1100         help
1101
1102 config FB_LE80578
1103         tristate "Intel LE80578 (Vermilion) support"
1104         depends on FB && PCI && X86
1105         select FB_MODE_HELPERS
1106         select FB_CFB_FILLRECT
1107         select FB_CFB_COPYAREA
1108         select FB_CFB_IMAGEBLIT
1109         help
1110           This driver supports the LE80578 (Vermilion Range) chipset
1111
1112 config FB_CARILLO_RANCH
1113         tristate "Intel Carillo Ranch support"
1114         depends on FB_LE80578 && FB && PCI && X86
1115         help
1116           This driver supports the LE80578 (Carillo Ranch) board
1117
1118 config FB_INTEL
1119         tristate "Intel 830M/845G/852GM/855GM/865G/915G/945G/945GM/965G/965GM support (EXPERIMENTAL)"
1120         depends on EXPERIMENTAL && FB && PCI && X86 && AGP_INTEL
1121         select FB_MODE_HELPERS
1122         select FB_CFB_FILLRECT
1123         select FB_CFB_COPYAREA
1124         select FB_CFB_IMAGEBLIT
1125         select FB_BOOT_VESA_SUPPORT if FB_INTEL = y
1126         help
1127           This driver supports the on-board graphics built in to the Intel
1128           830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/965G/965GM chipsets.
1129           Say Y if you have and plan to use such a board.
1130
1131           To make FB_INTELFB=Y work you need to say AGP_INTEL=y too.
1132
1133           To compile this driver as a module, choose M here: the
1134           module will be called intelfb.
1135
1136           For more information, please read <file:Documentation/fb/intelfb.txt>
1137
1138 config FB_INTEL_DEBUG
1139         bool "Intel driver Debug Messages"
1140         depends on FB_INTEL
1141         ---help---
1142           Say Y here if you want the Intel driver to output all sorts
1143           of debugging information to provide to the maintainer when
1144           something goes wrong.
1145
1146 config FB_INTEL_I2C
1147         bool "DDC/I2C for Intel framebuffer support"
1148         depends on FB_INTEL
1149         select FB_DDC
1150         default y
1151         help
1152           Say Y here if you want DDC/I2C support for your on-board Intel graphics.
1153
1154 config FB_MATROX
1155         tristate "Matrox acceleration"
1156         depends on FB && PCI
1157         select FB_CFB_FILLRECT
1158         select FB_CFB_COPYAREA
1159         select FB_CFB_IMAGEBLIT
1160         select FB_TILEBLITTING
1161         select FB_MACMODES if PPC_PMAC
1162         ---help---
1163           Say Y here if you have a Matrox Millennium, Matrox Millennium II,
1164           Matrox Mystique, Matrox Mystique 220, Matrox Productiva G100, Matrox
1165           Mystique G200, Matrox Millennium G200, Matrox Marvel G200 video,
1166           Matrox G400, G450 or G550 card in your box.
1167
1168           To compile this driver as a module, choose M here: the
1169           module will be called matroxfb.
1170
1171           You can pass several parameters to the driver at boot time or at
1172           module load time. The parameters look like "video=matrox:XXX", and
1173           are described in <file:Documentation/fb/matroxfb.txt>.
1174
1175 config FB_MATROX_MILLENIUM
1176         bool "Millennium I/II support"
1177         depends on FB_MATROX
1178         help
1179           Say Y here if you have a Matrox Millennium or Matrox Millennium II
1180           video card. If you select "Advanced lowlevel driver options" below,
1181           you should check 4 bpp packed pixel, 8 bpp packed pixel, 16 bpp
1182           packed pixel, 24 bpp packed pixel and 32 bpp packed pixel. You can
1183           also use font widths different from 8.
1184
1185 config FB_MATROX_MYSTIQUE
1186         bool "Mystique support"
1187         depends on FB_MATROX
1188         help
1189           Say Y here if you have a Matrox Mystique or Matrox Mystique 220
1190           video card. If you select "Advanced lowlevel driver options" below,
1191           you should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp
1192           packed pixel and 32 bpp packed pixel. You can also use font widths
1193           different from 8.
1194
1195 config FB_MATROX_G
1196         bool "G100/G200/G400/G450/G550 support"
1197         depends on FB_MATROX
1198         ---help---
1199           Say Y here if you have a Matrox G100, G200, G400, G450 or G550 based
1200           video card. If you select "Advanced lowlevel driver options", you
1201           should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp packed
1202           pixel and 32 bpp packed pixel. You can also use font widths
1203           different from 8.
1204
1205           If you need support for G400 secondary head, you must say Y to
1206           "Matrox I2C support" and "G400 second head support" right below.
1207           G450/G550 secondary head and digital output are supported without
1208           additional modules.
1209
1210           The driver starts in monitor mode. You must use the matroxset tool
1211           (available at <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to
1212           swap primary and secondary head outputs, or to change output mode.
1213           Secondary head driver always start in 640x480 resolution and you
1214           must use fbset to change it.
1215
1216           Do not forget that second head supports only 16 and 32 bpp
1217           packed pixels, so it is a good idea to compile them into the kernel
1218           too. You can use only some font widths, as the driver uses generic
1219           painting procedures (the secondary head does not use acceleration
1220           engine).
1221
1222           G450/G550 hardware can display TV picture only from secondary CRTC,
1223           and it performs no scaling, so picture must have 525 or 625 lines.
1224
1225 config FB_MATROX_I2C
1226         tristate "Matrox I2C support"
1227         depends on FB_MATROX
1228         select FB_DDC
1229         ---help---
1230           This drivers creates I2C buses which are needed for accessing the
1231           DDC (I2C) bus present on all Matroxes, an I2C bus which
1232           interconnects Matrox optional devices, like MGA-TVO on G200 and
1233           G400, and the secondary head DDC bus, present on G400 only.
1234
1235           You can say Y or M here if you want to experiment with monitor
1236           detection code. You must say Y or M here if you want to use either
1237           second head of G400 or MGA-TVO on G200 or G400.
1238
1239           If you compile it as module, it will create a module named
1240           i2c-matroxfb.
1241
1242 config FB_MATROX_MAVEN
1243         tristate "G400 second head support"
1244         depends on FB_MATROX_G && FB_MATROX_I2C
1245         ---help---
1246           WARNING !!! This support does not work with G450 !!!
1247
1248           Say Y or M here if you want to use a secondary head (meaning two
1249           monitors in parallel) on G400 or MGA-TVO add-on on G200. Secondary
1250           head is not compatible with accelerated XFree 3.3.x SVGA servers -
1251           secondary head output is blanked while you are in X. With XFree
1252           3.9.17 preview you can use both heads if you use SVGA over fbdev or
1253           the fbdev driver on first head and the fbdev driver on second head.
1254
1255           If you compile it as module, two modules are created,
1256           matroxfb_crtc2 and matroxfb_maven. Matroxfb_maven is needed for
1257           both G200 and G400, matroxfb_crtc2 is needed only by G400. You must
1258           also load i2c-matroxfb to get it to run.
1259
1260           The driver starts in monitor mode and you must use the matroxset
1261           tool (available at
1262           <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to switch it to
1263           PAL or NTSC or to swap primary and secondary head outputs.
1264           Secondary head driver also always start in 640x480 resolution, you
1265           must use fbset to change it.
1266
1267           Also do not forget that second head supports only 16 and 32 bpp
1268           packed pixels, so it is a good idea to compile them into the kernel
1269           too.  You can use only some font widths, as the driver uses generic
1270           painting procedures (the secondary head does not use acceleration
1271           engine).
1272
1273 config FB_MATROX_MULTIHEAD
1274         bool "Multihead support"
1275         depends on FB_MATROX
1276         ---help---
1277           Say Y here if you have more than one (supported) Matrox device in
1278           your computer and you want to use all of them for different monitors
1279           ("multihead"). If you have only one device, you should say N because
1280           the driver compiled with Y is larger and a bit slower, especially on
1281           ia32 (ix86).
1282
1283           If you said M to "Matrox unified accelerated driver" and N here, you
1284           will still be able to use several Matrox devices simultaneously:
1285           insert several instances of the module matroxfb into the kernel
1286           with insmod, supplying the parameter "dev=N" where N is 0, 1, etc.
1287           for the different Matrox devices. This method is slightly faster but
1288           uses 40 KB of kernel memory per Matrox card.
1289
1290           There is no need for enabling 'Matrox multihead support' if you have
1291           only one Matrox card in the box.
1292
1293 config FB_RADEON
1294         tristate "ATI Radeon display support"
1295         depends on FB && PCI
1296         select FB_BACKLIGHT if FB_RADEON_BACKLIGHT
1297         select FB_MODE_HELPERS
1298         select FB_CFB_FILLRECT
1299         select FB_CFB_COPYAREA
1300         select FB_CFB_IMAGEBLIT
1301         select FB_MACMODES if PPC_OF
1302         help
1303           Choose this option if you want to use an ATI Radeon graphics card as
1304           a framebuffer device.  There are both PCI and AGP versions.  You
1305           don't need to choose this to run the Radeon in plain VGA mode.
1306
1307           There is a product page at
1308           http://apps.ati.com/ATIcompare/
1309
1310 config FB_RADEON_I2C
1311         bool "DDC/I2C for ATI Radeon support"
1312         depends on FB_RADEON
1313         select FB_DDC
1314         default y
1315         help
1316           Say Y here if you want DDC/I2C support for your Radeon board.
1317
1318 config FB_RADEON_BACKLIGHT
1319         bool "Support for backlight control"
1320         depends on FB_RADEON
1321         default y
1322         help
1323           Say Y here if you want to control the backlight of your display.
1324
1325 config FB_RADEON_DEBUG
1326         bool "Lots of debug output from Radeon driver"
1327         depends on FB_RADEON
1328         default n
1329         help
1330           Say Y here if you want the Radeon driver to output all sorts
1331           of debugging information to provide to the maintainer when
1332           something goes wrong.
1333
1334 config FB_ATY128
1335         tristate "ATI Rage128 display support"
1336         depends on FB && PCI
1337         select FB_CFB_FILLRECT
1338         select FB_CFB_COPYAREA
1339         select FB_CFB_IMAGEBLIT
1340         select FB_BACKLIGHT if FB_ATY128_BACKLIGHT
1341         select FB_MACMODES if PPC_PMAC
1342         help
1343           This driver supports graphics boards with the ATI Rage128 chips.
1344           Say Y if you have such a graphics board and read
1345           <file:Documentation/fb/aty128fb.txt>.
1346
1347           To compile this driver as a module, choose M here: the
1348           module will be called aty128fb.
1349
1350 config FB_ATY128_BACKLIGHT
1351         bool "Support for backlight control"
1352         depends on FB_ATY128
1353         default y
1354         help
1355           Say Y here if you want to control the backlight of your display.
1356
1357 config FB_ATY
1358         tristate "ATI Mach64 display support" if PCI || ATARI
1359         depends on FB && !SPARC32
1360         select FB_CFB_FILLRECT
1361         select FB_CFB_COPYAREA
1362         select FB_CFB_IMAGEBLIT
1363         select FB_BACKLIGHT if FB_ATY_BACKLIGHT
1364         select FB_MACMODES if PPC
1365         help
1366           This driver supports graphics boards with the ATI Mach64 chips.
1367           Say Y if you have such a graphics board.
1368
1369           To compile this driver as a module, choose M here: the
1370           module will be called atyfb.
1371
1372 config FB_ATY_CT
1373         bool "Mach64 CT/VT/GT/LT (incl. 3D RAGE) support"
1374         depends on PCI && FB_ATY
1375         default y if SPARC64 && PCI
1376         help
1377           Say Y here to support use of ATI's 64-bit Rage boards (or other
1378           boards based on the Mach64 CT, VT, GT, and LT chipsets) as a
1379           framebuffer device.  The ATI product support page for these boards
1380           is at <http://support.ati.com/products/pc/mach64/>.
1381
1382 config FB_ATY_GENERIC_LCD
1383         bool "Mach64 generic LCD support (EXPERIMENTAL)"
1384         depends on FB_ATY_CT
1385         help
1386           Say Y if you have a laptop with an ATI Rage LT PRO, Rage Mobility,
1387           Rage XC, or Rage XL chipset.
1388
1389 config FB_ATY_GX
1390         bool "Mach64 GX support" if PCI
1391         depends on FB_ATY
1392         default y if ATARI
1393         help
1394           Say Y here to support use of the ATI Mach64 Graphics Expression
1395           board (or other boards based on the Mach64 GX chipset) as a
1396           framebuffer device.  The ATI product support page for these boards
1397           is at
1398           <http://support.ati.com/products/pc/mach64/graphics_xpression.html>.
1399
1400 config FB_ATY_BACKLIGHT
1401         bool "Support for backlight control"
1402         depends on FB_ATY
1403         default y
1404         help
1405           Say Y here if you want to control the backlight of your display.
1406
1407 config FB_S3
1408         tristate "S3 Trio/Virge support"
1409         depends on FB && PCI
1410         select FB_CFB_FILLRECT
1411         select FB_CFB_COPYAREA
1412         select FB_CFB_IMAGEBLIT
1413         select FB_TILEBLITTING
1414         select FB_SVGALIB
1415         select VGASTATE
1416         select FONT_8x16 if FRAMEBUFFER_CONSOLE
1417         ---help---
1418           Driver for graphics boards with S3 Trio / S3 Virge chip.
1419
1420 config FB_SAVAGE
1421         tristate "S3 Savage support"
1422         depends on FB && PCI && EXPERIMENTAL
1423         select FB_MODE_HELPERS
1424         select FB_CFB_FILLRECT
1425         select FB_CFB_COPYAREA
1426         select FB_CFB_IMAGEBLIT
1427         select VGASTATE
1428         help
1429           This driver supports notebooks and computers with S3 Savage PCI/AGP
1430           chips.
1431
1432           Say Y if you have such a graphics card.
1433
1434           To compile this driver as a module, choose M here; the module
1435           will be called savagefb.
1436
1437 config FB_SAVAGE_I2C
1438        bool "Enable DDC2 Support"
1439        depends on FB_SAVAGE
1440        select FB_DDC
1441        help
1442           This enables I2C support for S3 Savage Chipsets.  This is used
1443           only for getting EDID information from the attached display
1444           allowing for robust video mode handling and switching.
1445
1446           Because fbdev-2.6 requires that drivers must be able to
1447           independently validate video mode parameters, you should say Y
1448           here.
1449
1450 config FB_SAVAGE_ACCEL
1451        bool "Enable Console Acceleration"
1452        depends on FB_SAVAGE
1453        default n
1454        help
1455           This option will compile in console acceleration support. If
1456           the resulting framebuffer console has bothersome glitches, then
1457           choose N here.
1458
1459 config FB_SIS
1460         tristate "SiS/XGI display support"
1461         depends on FB && PCI
1462         select FB_CFB_FILLRECT
1463         select FB_CFB_COPYAREA
1464         select FB_CFB_IMAGEBLIT
1465         select FB_BOOT_VESA_SUPPORT if FB_SIS = y
1466         help
1467           This is the frame buffer device driver for the SiS 300, 315, 330
1468           and 340 series as well as XGI V3XT, V5, V8, Z7 graphics chipsets.
1469           Specs available at <http://www.sis.com> and <http://www.xgitech.com>.
1470
1471           To compile this driver as a module, choose M here; the module
1472           will be called sisfb.
1473
1474 config FB_SIS_300
1475         bool "SiS 300 series support"
1476         depends on FB_SIS
1477         help
1478           Say Y here to support use of the SiS 300/305, 540, 630 and 730.
1479
1480 config FB_SIS_315
1481         bool "SiS 315/330/340 series and XGI support"
1482         depends on FB_SIS
1483         help
1484           Say Y here to support use of the SiS 315, 330 and 340 series
1485           (315/H/PRO, 55x, 650, 651, 740, 330, 661, 741, 760, 761) as well
1486           as XGI V3XT, V5, V8 and Z7.
1487
1488 config FB_VIA
1489        tristate "VIA UniChrome (Pro) and Chrome9 display support"
1490        depends on FB && PCI
1491        select FB_CFB_FILLRECT
1492        select FB_CFB_COPYAREA
1493        select FB_CFB_IMAGEBLIT
1494        select FB_SOFT_CURSOR
1495        select I2C_ALGOBIT
1496        select I2C
1497        help
1498           This is the frame buffer device driver for Graphics chips of VIA
1499           UniChrome (Pro) Family (CLE266,PM800/CN400,P4M800CE/P4M800Pro/
1500           CN700/VN800,CX700/VX700,P4M890) and Chrome9 Family (K8M890,CN896
1501           /P4M900,VX800)
1502           Say Y if you have a VIA UniChrome graphics board.
1503
1504           To compile this driver as a module, choose M here: the
1505           module will be called viafb.
1506 config FB_NEOMAGIC
1507         tristate "NeoMagic display support"
1508         depends on FB && PCI
1509         select FB_MODE_HELPERS
1510         select FB_CFB_FILLRECT
1511         select FB_CFB_COPYAREA
1512         select FB_CFB_IMAGEBLIT
1513         select VGASTATE
1514         help
1515           This driver supports notebooks with NeoMagic PCI chips.
1516           Say Y if you have such a graphics card.
1517
1518           To compile this driver as a module, choose M here: the
1519           module will be called neofb.
1520
1521 config FB_KYRO
1522         tristate "IMG Kyro support"
1523         depends on FB && PCI
1524         select FB_CFB_FILLRECT
1525         select FB_CFB_COPYAREA
1526         select FB_CFB_IMAGEBLIT
1527         help
1528           Say Y here if you have a STG4000 / Kyro / PowerVR 3 based
1529           graphics board.
1530
1531           To compile this driver as a module, choose M here: the
1532           module will be called kyrofb.
1533
1534 config FB_3DFX
1535         tristate "3Dfx Banshee/Voodoo3/Voodoo5 display support"
1536         depends on FB && PCI
1537         select FB_CFB_IMAGEBLIT
1538         select FB_CFB_FILLRECT
1539         select FB_CFB_COPYAREA
1540         select FB_MODE_HELPERS
1541         help
1542           This driver supports graphics boards with the 3Dfx Banshee,
1543           Voodoo3 or VSA-100 (aka Voodoo4/5) chips. Say Y if you have
1544           such a graphics board.
1545
1546           To compile this driver as a module, choose M here: the
1547           module will be called tdfxfb.
1548
1549 config FB_3DFX_ACCEL
1550         bool "3Dfx Acceleration functions (EXPERIMENTAL)"
1551         depends on FB_3DFX && EXPERIMENTAL
1552         ---help---
1553         This will compile the 3Dfx Banshee/Voodoo3/VSA-100 frame buffer
1554         device driver with acceleration functions.
1555
1556 config FB_3DFX_I2C
1557         bool "Enable DDC/I2C support"
1558         depends on FB_3DFX && EXPERIMENTAL
1559         select FB_DDC
1560         default y
1561         help
1562           Say Y here if you want DDC/I2C support for your 3dfx Voodoo3.
1563
1564 config FB_VOODOO1
1565         tristate "3Dfx Voodoo Graphics (sst1) support"
1566         depends on FB && PCI
1567         select FB_CFB_FILLRECT
1568         select FB_CFB_COPYAREA
1569         select FB_CFB_IMAGEBLIT
1570         ---help---
1571           Say Y here if you have a 3Dfx Voodoo Graphics (Voodoo1/sst1) or
1572           Voodoo2 (cvg) based graphics card.
1573
1574           To compile this driver as a module, choose M here: the
1575           module will be called sstfb.
1576
1577           WARNING: Do not use any application that uses the 3D engine
1578           (namely glide) while using this driver.
1579           Please read the <file:Documentation/fb/sstfb.txt> for supported
1580           options and other important info  support.
1581
1582 config FB_VT8623
1583         tristate "VIA VT8623 support"
1584         depends on FB && PCI
1585         select FB_CFB_FILLRECT
1586         select FB_CFB_COPYAREA
1587         select FB_CFB_IMAGEBLIT
1588         select FB_TILEBLITTING
1589         select FB_SVGALIB
1590         select VGASTATE
1591         select FONT_8x16 if FRAMEBUFFER_CONSOLE
1592         ---help---
1593           Driver for CastleRock integrated graphics core in the
1594           VIA VT8623 [Apollo CLE266] chipset.
1595
1596 config FB_TRIDENT
1597         tristate "Trident/CyberXXX/CyberBlade support"
1598         depends on FB && PCI
1599         select FB_CFB_FILLRECT
1600         select FB_CFB_COPYAREA
1601         select FB_CFB_IMAGEBLIT
1602         ---help---
1603           This is the frame buffer device driver for Trident PCI/AGP chipsets.
1604           Supported chipset families are TGUI 9440/96XX, 3DImage, Blade3D
1605           and Blade XP.
1606           There are also integrated versions of these chips called CyberXXXX,
1607           CyberImage or CyberBlade. These chips are mostly found in laptops
1608           but also on some motherboards including early VIA EPIA motherboards.
1609           For more information, read <file:Documentation/fb/tridentfb.txt>
1610
1611           Say Y if you have such a graphics board.
1612
1613           To compile this driver as a module, choose M here: the
1614           module will be called tridentfb.
1615
1616 config FB_ARK
1617         tristate "ARK 2000PV support"
1618         depends on FB && PCI
1619         select FB_CFB_FILLRECT
1620         select FB_CFB_COPYAREA
1621         select FB_CFB_IMAGEBLIT
1622         select FB_TILEBLITTING
1623         select FB_SVGALIB
1624         select VGASTATE
1625         select FONT_8x16 if FRAMEBUFFER_CONSOLE
1626         ---help---
1627           Driver for PCI graphics boards with ARK 2000PV chip
1628           and ICS 5342 RAMDAC.
1629
1630 config FB_PM3
1631         tristate "Permedia3 support (EXPERIMENTAL)"
1632         depends on FB && PCI && EXPERIMENTAL
1633         select FB_CFB_FILLRECT
1634         select FB_CFB_COPYAREA
1635         select FB_CFB_IMAGEBLIT
1636         help
1637           This is the frame buffer device driver for the 3DLabs Permedia3
1638           chipset, used in Formac ProFormance III, 3DLabs Oxygen VX1 &
1639           similar boards, 3DLabs Permedia3 Create!, Appian Jeronimo 2000
1640           and maybe other boards.
1641
1642 config FB_CARMINE
1643         tristate "Fujitsu carmine frame buffer support"
1644         depends on FB && PCI
1645         select FB_CFB_FILLRECT
1646         select FB_CFB_COPYAREA
1647         select FB_CFB_IMAGEBLIT
1648         help
1649           This is the frame buffer device driver for the Fujitsu Carmine chip.
1650           The driver provides two independent frame buffer devices.
1651
1652 choice
1653         depends on FB_CARMINE
1654         prompt "DRAM timing"
1655         default FB_CARMINE_DRAM_EVAL
1656
1657 config FB_CARMINE_DRAM_EVAL
1658         bool "Eval board timings"
1659         help
1660           Use timings which work on the eval card.
1661
1662 config CARMINE_DRAM_CUSTOM
1663         bool "Custom board timings"
1664         help
1665           Use custom board timings.
1666 endchoice
1667
1668 config FB_AU1100
1669         bool "Au1100 LCD Driver"
1670         depends on (FB = y) && MIPS && SOC_AU1100
1671         select FB_CFB_FILLRECT
1672         select FB_CFB_COPYAREA
1673         select FB_CFB_IMAGEBLIT
1674         help
1675           This is the framebuffer driver for the AMD Au1100 SOC.  It can drive
1676           various panels and CRTs by passing in kernel cmd line option
1677           au1100fb:panel=<name>.
1678
1679 config FB_AU1200
1680         bool "Au1200 LCD Driver"
1681         depends on (FB = y) && MIPS && SOC_AU1200
1682         select FB_CFB_FILLRECT
1683         select FB_CFB_COPYAREA
1684         select FB_CFB_IMAGEBLIT
1685         help
1686           This is the framebuffer driver for the AMD Au1200 SOC.  It can drive
1687           various panels and CRTs by passing in kernel cmd line option
1688           au1200fb:panel=<name>.
1689
1690 source "drivers/video/geode/Kconfig"
1691
1692 config FB_HIT
1693         tristate "HD64461 Frame Buffer support"
1694         depends on FB && HD64461
1695         select FB_CFB_FILLRECT
1696         select FB_CFB_COPYAREA
1697         select FB_CFB_IMAGEBLIT
1698         help
1699           This is the frame buffer device driver for the Hitachi HD64461 LCD
1700           frame buffer card.
1701
1702 config FB_PMAG_AA
1703         bool "PMAG-AA TURBOchannel framebuffer support"
1704         depends on (FB = y) && TC
1705         select FB_CFB_FILLRECT
1706         select FB_CFB_COPYAREA
1707         select FB_CFB_IMAGEBLIT
1708         help
1709           Support for the PMAG-AA TURBOchannel framebuffer card (1280x1024x1)
1710           used mainly in the MIPS-based DECstation series.
1711
1712 config FB_PMAG_BA
1713         tristate "PMAG-BA TURBOchannel framebuffer support"
1714         depends on FB && TC
1715         select FB_CFB_FILLRECT
1716         select FB_CFB_COPYAREA
1717         select FB_CFB_IMAGEBLIT
1718         help
1719           Support for the PMAG-BA TURBOchannel framebuffer card (1024x864x8)
1720           used mainly in the MIPS-based DECstation series.
1721
1722 config FB_PMAGB_B
1723         tristate "PMAGB-B TURBOchannel framebuffer support"
1724         depends on FB && TC
1725         select FB_CFB_FILLRECT
1726         select FB_CFB_COPYAREA
1727         select FB_CFB_IMAGEBLIT
1728         help
1729           Support for the PMAGB-B TURBOchannel framebuffer card used mainly
1730           in the MIPS-based DECstation series. The card is currently only
1731           supported in 1280x1024x8 mode.
1732
1733 config FB_MAXINE
1734         bool "Maxine (Personal DECstation) onboard framebuffer support"
1735         depends on (FB = y) && MACH_DECSTATION
1736         select FB_CFB_FILLRECT
1737         select FB_CFB_COPYAREA
1738         select FB_CFB_IMAGEBLIT
1739         help
1740           Support for the onboard framebuffer (1024x768x8) in the Personal
1741           DECstation series (Personal DECstation 5000/20, /25, /33, /50,
1742           Codename "Maxine").
1743
1744 config FB_G364
1745         bool "G364 frame buffer support"
1746         depends on (FB = y) && (MIPS_MAGNUM_4000 || OLIVETTI_M700)
1747         select FB_CFB_FILLRECT
1748         select FB_CFB_COPYAREA
1749         select FB_CFB_IMAGEBLIT
1750         help
1751           The G364 driver is the framebuffer used in MIPS Magnum 4000 and
1752           Olivetti M700-10 systems.
1753
1754 config FB_68328
1755         bool "Motorola 68328 native frame buffer support"
1756         depends on (FB = y) && (M68328 || M68EZ328 || M68VZ328)
1757         select FB_CFB_FILLRECT
1758         select FB_CFB_COPYAREA
1759         select FB_CFB_IMAGEBLIT
1760         help
1761           Say Y here if you want to support the built-in frame buffer of
1762           the Motorola 68328 CPU family.
1763
1764 config FB_PXA168
1765         tristate "PXA168/910 LCD framebuffer support"
1766         depends on FB && (CPU_PXA168 || CPU_PXA910)
1767         select FB_CFB_FILLRECT
1768         select FB_CFB_COPYAREA
1769         select FB_CFB_IMAGEBLIT
1770         ---help---
1771           Frame buffer driver for the built-in LCD controller in the Marvell
1772           MMP processor.
1773
1774 config FB_PXA
1775         tristate "PXA LCD framebuffer support"
1776         depends on FB && ARCH_PXA
1777         select FB_CFB_FILLRECT
1778         select FB_CFB_COPYAREA
1779         select FB_CFB_IMAGEBLIT
1780         ---help---
1781           Frame buffer driver for the built-in LCD controller in the Intel
1782           PXA2x0 processor.
1783
1784           This driver is also available as a module ( = code which can be
1785           inserted and removed from the running kernel whenever you want). The
1786           module will be called pxafb. If you want to compile it as a module,
1787           say M here and read <file:Documentation/kbuild/modules.txt>.
1788
1789           If unsure, say N.
1790
1791 config FB_PXA_OVERLAY
1792         bool "Support PXA27x/PXA3xx Overlay(s) as framebuffer"
1793         default n
1794         depends on FB_PXA && (PXA27x || PXA3xx)
1795
1796 config FB_PXA_SMARTPANEL
1797         bool "PXA Smartpanel LCD support"
1798         default n
1799         depends on FB_PXA
1800
1801 config FB_PXA_PARAMETERS
1802         bool "PXA LCD command line parameters"
1803         default n
1804         depends on FB_PXA
1805         ---help---
1806           Enable the use of kernel command line or module parameters
1807           to configure the physical properties of the LCD panel when
1808           using the PXA LCD driver.
1809
1810           This option allows you to override the panel parameters
1811           supplied by the platform in order to support multiple
1812           different models of flatpanel. If you will only be using a
1813           single model of flatpanel then you can safely leave this
1814           option disabled.
1815
1816           <file:Documentation/fb/pxafb.txt> describes the available parameters.
1817
1818 config FB_MBX
1819         tristate "2700G LCD framebuffer support"
1820         depends on FB && ARCH_PXA
1821         select FB_CFB_FILLRECT
1822         select FB_CFB_COPYAREA
1823         select FB_CFB_IMAGEBLIT
1824         ---help---
1825           Framebuffer driver for the Intel 2700G (Marathon) Graphics
1826           Accelerator
1827
1828 config FB_MBX_DEBUG
1829        bool "Enable debugging info via debugfs"
1830        depends on FB_MBX && DEBUG_FS
1831        default n
1832        ---help---
1833          Enable this if you want debugging information using the debug
1834          filesystem (debugfs)
1835
1836          If unsure, say N.
1837
1838 config FB_FSL_DIU
1839         tristate "Freescale DIU framebuffer support"
1840         depends on FB && FSL_SOC
1841         select FB_CFB_FILLRECT
1842         select FB_CFB_COPYAREA
1843         select FB_CFB_IMAGEBLIT
1844         select PPC_LIB_RHEAP
1845         ---help---
1846           Framebuffer driver for the Freescale SoC DIU
1847
1848 config FB_W100
1849         tristate "W100 frame buffer support"
1850         depends on FB && ARCH_PXA
1851         select FB_CFB_FILLRECT
1852         select FB_CFB_COPYAREA
1853         select FB_CFB_IMAGEBLIT
1854         ---help---
1855           Frame buffer driver for the w100 as found on the Sharp SL-Cxx series.
1856           It can also drive the w3220 chip found on iPAQ hx4700.
1857
1858           This driver is also available as a module ( = code which can be
1859           inserted and removed from the running kernel whenever you want). The
1860           module will be called w100fb. If you want to compile it as a module,
1861           say M here and read <file:Documentation/kbuild/modules.txt>.
1862
1863           If unsure, say N.
1864
1865 config FB_SH_MOBILE_LCDC
1866         tristate "SuperH Mobile LCDC framebuffer support"
1867         depends on FB && SUPERH
1868         select FB_SYS_FILLRECT
1869         select FB_SYS_COPYAREA
1870         select FB_SYS_IMAGEBLIT
1871         select FB_SYS_FOPS
1872         select FB_DEFERRED_IO
1873         ---help---
1874           Frame buffer driver for the on-chip SH-Mobile LCD controller.
1875
1876 config FB_TMIO
1877         tristate "Toshiba Mobile IO FrameBuffer support"
1878         depends on FB && MFD_CORE
1879         select FB_CFB_FILLRECT
1880         select FB_CFB_COPYAREA
1881         select FB_CFB_IMAGEBLIT
1882         ---help---
1883           Frame buffer driver for the Toshiba Mobile IO integrated as found
1884           on the Sharp SL-6000 series
1885
1886           This driver is also available as a module ( = code which can be
1887           inserted and removed from the running kernel whenever you want). The
1888           module will be called tmiofb. If you want to compile it as a module,
1889           say M here and read <file:Documentation/kbuild/modules.txt>.
1890
1891           If unsure, say N.
1892
1893 config FB_TMIO_ACCELL
1894         bool "tmiofb acceleration"
1895         depends on FB_TMIO
1896         default y
1897
1898 config FB_S3C
1899         tristate "Samsung S3C framebuffer support"
1900         depends on FB && ARCH_S3C64XX
1901         select FB_CFB_FILLRECT
1902         select FB_CFB_COPYAREA
1903         select FB_CFB_IMAGEBLIT
1904         ---help---
1905           Frame buffer driver for the built-in FB controller in the Samsung
1906           SoC line from the S3C2443 onwards, including the S3C2416, S3C2450,
1907           and the S3C64XX series such as the S3C6400 and S3C6410.
1908
1909           These chips all have the same basic framebuffer design with the
1910           actual capabilities depending on the chip. For instance the S3C6400
1911           and S3C6410 support 4 hardware windows whereas the S3C24XX series
1912           currently only have two.
1913
1914           Currently the support is only for the S3C6400 and S3C6410 SoCs.
1915
1916 config FB_S3C_DEBUG_REGWRITE
1917        bool "Debug register writes"
1918        depends on FB_S3C
1919        ---help---
1920          Show all register writes via printk(KERN_DEBUG)
1921
1922 config FB_S3C2410
1923         tristate "S3C2410 LCD framebuffer support"
1924         depends on FB && ARCH_S3C2410
1925         select FB_CFB_FILLRECT
1926         select FB_CFB_COPYAREA
1927         select FB_CFB_IMAGEBLIT
1928         ---help---
1929           Frame buffer driver for the built-in LCD controller in the Samsung
1930           S3C2410 processor.
1931
1932           This driver is also available as a module ( = code which can be
1933           inserted and removed from the running kernel whenever you want). The
1934           module will be called s3c2410fb. If you want to compile it as a module,
1935           say M here and read <file:Documentation/kbuild/modules.txt>.
1936
1937           If unsure, say N.
1938 config FB_S3C2410_DEBUG
1939         bool "S3C2410 lcd debug messages"
1940         depends on FB_S3C2410
1941         help
1942           Turn on debugging messages. Note that you can set/unset at run time
1943           through sysfs
1944
1945 config FB_SM501
1946         tristate "Silicon Motion SM501 framebuffer support"
1947         depends on FB && MFD_SM501
1948         select FB_CFB_FILLRECT
1949         select FB_CFB_COPYAREA
1950         select FB_CFB_IMAGEBLIT
1951         ---help---
1952           Frame buffer driver for the CRT and LCD controllers in the Silicon
1953           Motion SM501.
1954
1955           This driver is also available as a module ( = code which can be
1956           inserted and removed from the running kernel whenever you want). The
1957           module will be called sm501fb. If you want to compile it as a module,
1958           say M here and read <file:Documentation/kbuild/modules.txt>.
1959
1960           If unsure, say N.
1961
1962
1963 config FB_PNX4008_DUM
1964         tristate "Display Update Module support on Philips PNX4008 board"
1965         depends on FB && ARCH_PNX4008
1966         ---help---
1967           Say Y here to enable support for PNX4008 Display Update Module (DUM)
1968
1969 config FB_PNX4008_DUM_RGB
1970         tristate "RGB Framebuffer support on Philips PNX4008 board"
1971         depends on FB_PNX4008_DUM
1972         select FB_CFB_FILLRECT
1973         select FB_CFB_COPYAREA
1974         select FB_CFB_IMAGEBLIT
1975         ---help---
1976           Say Y here to enable support for PNX4008 RGB Framebuffer
1977
1978 config FB_IBM_GXT4500
1979         tristate "Framebuffer support for IBM GXT4500P adaptor"
1980         depends on FB && PPC
1981         select FB_CFB_FILLRECT
1982         select FB_CFB_COPYAREA
1983         select FB_CFB_IMAGEBLIT
1984         ---help---
1985           Say Y here to enable support for the IBM GXT4500P display
1986           adaptor, found on some IBM System P (pSeries) machines.
1987
1988 config FB_PS3
1989         tristate "PS3 GPU framebuffer driver"
1990         depends on FB && PS3_PS3AV
1991         select FB_SYS_FILLRECT
1992         select FB_SYS_COPYAREA
1993         select FB_SYS_IMAGEBLIT
1994         select FB_SYS_FOPS
1995         select VT_HW_CONSOLE_BINDING if FRAMEBUFFER_CONSOLE
1996         ---help---
1997           Include support for the virtual frame buffer in the PS3 platform.
1998
1999 config FB_PS3_DEFAULT_SIZE_M
2000         int "PS3 default frame buffer size (in MiB)"
2001         depends on FB_PS3
2002         default 9
2003         ---help---
2004           This is the default size (in MiB) of the virtual frame buffer in
2005           the PS3.
2006           The default value can be overridden on the kernel command line
2007           using the "ps3fb" option (e.g. "ps3fb=9M");
2008
2009 config FB_XILINX
2010         tristate "Xilinx frame buffer support"
2011         depends on FB && (XILINX_VIRTEX || MICROBLAZE)
2012         select FB_CFB_FILLRECT
2013         select FB_CFB_COPYAREA
2014         select FB_CFB_IMAGEBLIT
2015         ---help---
2016           Include support for the Xilinx ML300/ML403 reference design
2017           framebuffer. ML300 carries a 640*480 LCD display on the board,
2018           ML403 uses a standard DB15 VGA connector.
2019
2020 config FB_COBALT
2021         tristate "Cobalt server LCD frame buffer support"
2022         depends on FB && MIPS_COBALT
2023
2024 config FB_SH7760
2025         bool "SH7760/SH7763/SH7720/SH7721 LCDC support"
2026         depends on FB && (CPU_SUBTYPE_SH7760 || CPU_SUBTYPE_SH7763 \
2027                 || CPU_SUBTYPE_SH7720 || CPU_SUBTYPE_SH7721)
2028         select FB_CFB_FILLRECT
2029         select FB_CFB_COPYAREA
2030         select FB_CFB_IMAGEBLIT
2031         ---help---
2032           Support for the SH7760/SH7763/SH7720/SH7721 integrated
2033           (D)STN/TFT LCD Controller.
2034           Supports display resolutions up to 1024x1024 pixel, grayscale and
2035           color operation, with depths ranging from 1 bpp to 8 bpp monochrome
2036           and 8, 15 or 16 bpp color; 90 degrees clockwise display rotation for
2037           panels <= 320 pixel horizontal resolution.
2038
2039 config FB_VIRTUAL
2040         tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)"
2041         depends on FB
2042         select FB_SYS_FILLRECT
2043         select FB_SYS_COPYAREA
2044         select FB_SYS_IMAGEBLIT
2045         select FB_SYS_FOPS
2046         ---help---
2047           This is a `virtual' frame buffer device. It operates on a chunk of
2048           unswappable kernel memory instead of on the memory of a graphics
2049           board. This means you cannot see any output sent to this frame
2050           buffer device, while it does consume precious memory. The main use
2051           of this frame buffer device is testing and debugging the frame
2052           buffer subsystem. Do NOT enable it for normal systems! To protect
2053           the innocent, it has to be enabled explicitly at boot time using the
2054           kernel option `video=vfb:'.
2055
2056           To compile this driver as a module, choose M here: the
2057           module will be called vfb. In order to load it, you must use
2058           the vfb_enable=1 option.
2059
2060           If unsure, say N.
2061
2062 config XEN_FBDEV_FRONTEND
2063         tristate "Xen virtual frame buffer support"
2064         depends on FB && XEN
2065         select FB_SYS_FILLRECT
2066         select FB_SYS_COPYAREA
2067         select FB_SYS_IMAGEBLIT
2068         select FB_SYS_FOPS
2069         select FB_DEFERRED_IO
2070         default y
2071         help
2072           This driver implements the front-end of the Xen virtual
2073           frame buffer driver.  It communicates with a back-end
2074           in another domain.
2075
2076 config FB_METRONOME
2077         tristate "E-Ink Metronome/8track controller support"
2078         depends on FB
2079         select FB_SYS_FILLRECT
2080         select FB_SYS_COPYAREA
2081         select FB_SYS_IMAGEBLIT
2082         select FB_SYS_FOPS
2083         select FB_DEFERRED_IO
2084         help
2085           This driver implements support for the E-Ink Metronome
2086           controller. The pre-release name for this device was 8track
2087           and could also have been called by some vendors as PVI-nnnn.
2088
2089 config FB_MB862XX
2090         tristate "Fujitsu MB862xx GDC support"
2091         depends on FB
2092         select FB_CFB_FILLRECT
2093         select FB_CFB_COPYAREA
2094         select FB_CFB_IMAGEBLIT
2095         ---help---
2096           Frame buffer driver for Fujitsu Carmine/Coral-P(A)/Lime controllers.
2097
2098 config FB_MB862XX_PCI_GDC
2099         bool "Carmine/Coral-P(A) GDC"
2100         depends on PCI && FB_MB862XX
2101         ---help---
2102           This enables framebuffer support for Fujitsu Carmine/Coral-P(A)
2103           PCI graphics controller devices.
2104
2105 config FB_MB862XX_LIME
2106         bool "Lime GDC"
2107         depends on FB_MB862XX
2108         depends on OF && !FB_MB862XX_PCI_GDC
2109         depends on PPC
2110         select FB_FOREIGN_ENDIAN
2111         select FB_LITTLE_ENDIAN
2112         ---help---
2113           Framebuffer support for Fujitsu Lime GDC on host CPU bus.
2114
2115 config FB_PRE_INIT_FB
2116         bool "Don't reinitialize, use bootloader's GDC/Display configuration"
2117         depends on FB_MB862XX_LIME
2118         ---help---
2119           Select this option if display contents should be inherited as set by
2120           the bootloader.
2121
2122 config FB_MX3
2123         tristate "MX3 Framebuffer support"
2124         depends on FB && MX3_IPU
2125         select FB_CFB_FILLRECT
2126         select FB_CFB_COPYAREA
2127         select FB_CFB_IMAGEBLIT
2128         default y
2129         help
2130           This is a framebuffer device for the i.MX31 LCD Controller. So
2131           far only synchronous displays are supported. If you plan to use
2132           an LCD display with your i.MX31 system, say Y here.
2133
2134 config FB_BROADSHEET
2135         tristate "E-Ink Broadsheet/Epson S1D13521 controller support"
2136         depends on FB
2137         select FB_SYS_FILLRECT
2138         select FB_SYS_COPYAREA
2139         select FB_SYS_IMAGEBLIT
2140         select FB_SYS_FOPS
2141         select FB_DEFERRED_IO
2142         help
2143           This driver implements support for the E-Ink Broadsheet
2144           controller. The release name for this device was Epson S1D13521
2145           and could also have been called by other names when coupled with
2146           a bridge adapter.
2147
2148 source "drivers/video/omap/Kconfig"
2149
2150 source "drivers/video/backlight/Kconfig"
2151 source "drivers/video/display/Kconfig"
2152
2153 if VT
2154         source "drivers/video/console/Kconfig"
2155 endif
2156
2157 if FB || SGI_NEWPORT_CONSOLE
2158         source "drivers/video/logo/Kconfig"
2159 endif
2160
2161 endmenu