drivers/w1/slaves/Kconfig

   1 #
   2 # 1-wire slaves configuration
   3 #
   4
   5 menu "1-wire Slaves"
   6
   7 config W1_SLAVE_THERM
   8         tristate "Thermal family implementation"
   9         help
  10           Say Y here if you want to connect 1-wire thermal sensors to your
  11           wire.
  12
  13 config W1_SLAVE_SMEM
  14         tristate "Simple 64bit memory family implementation"
  15         help
  16           Say Y here if you want to connect 1-wire
  17           simple 64bit memory rom(ds2401/ds2411/ds1990*) to your wire.
  18
  19 config W1_SLAVE_DS2408
  20         tristate "8-Channel Addressable Switch (IO Expander) 0x29 family support (DS2408)"
  21         help
  22           Say Y here if you want to use a 1-wire
  23           DS2408 8-Channel Addressable Switch device support
  24
  25 config W1_SLAVE_DS2408_READBACK
  26         bool "Read-back values written to DS2408's output register"
  27         depends on W1_SLAVE_DS2408
  28         default y
  29         help
  30           Enabling this will cause the driver to read back the values written
  31           to the chip's output register in order to detect errors.
  32
  33           This is slower but useful when debugging chips and/or busses.
  34
  35 config W1_SLAVE_DS2413
  36         tristate "Dual Channel Addressable Switch 0x3a family support (DS2413)"
  37         help
  38           Say Y here if you want to use a 1-wire
  39           DS2413 Dual Channel Addressable Switch device support
  40
  41 config W1_SLAVE_DS2406
  42         tristate "Dual Channel Addressable Switch 0x12 family support (DS2406)"
  43         select CRC16
  44         help
  45           Say Y or M here if you want to use a 1-wire
  46           DS2406 Dual Channel Addressable Switch.  EPROM read/write
  47           support for these devices is not implemented.
  48
  49 config W1_SLAVE_DS2423
  50         tristate "Counter 1-wire device (DS2423)"
  51         select CRC16
  52         help
  53           If you enable this you can read the counter values available
  54           in the DS2423 chipset from the w1_slave file under the
  55           sys file system.
  56
  57           Say Y here if you want to use a 1-wire
  58           counter family device (DS2423).
  59
  60 config W1_SLAVE_DS2431
  61         tristate "1kb EEPROM family support (DS2431)"
  62         help
  63           Say Y here if you want to use a 1-wire
  64           1kb EEPROM family device (DS2431)
  65
  66 config W1_SLAVE_DS2433
  67         tristate "4kb EEPROM family support (DS2433)"
  68         help
  69           Say Y here if you want to use a 1-wire
  70           4kb EEPROM family device (DS2433).
  71
  72 config W1_SLAVE_DS2433_CRC
  73         bool "Protect DS2433 data with a CRC16"
  74         depends on W1_SLAVE_DS2433
  75         select CRC16
  76         help
  77           Say Y here to protect DS2433 data with a CRC16.
  78           Each block has 30 bytes of data and a two byte CRC16.
  79           Full block writes are only allowed if the CRC is valid.
  80
  81 config W1_SLAVE_DS2760
  82         tristate "Dallas 2760 battery monitor chip (HP iPAQ & others)"
  83         help
  84           If you enable this you will have the DS2760 battery monitor
  85           chip support.
  86
  87           The battery monitor chip is used in many batteries/devices
  88           as the one who is responsible for charging/discharging/monitoring
  89           Li+ batteries.
  90
  91           If you are unsure, say N.
  92
  93 config W1_SLAVE_DS2780
  94         tristate "Dallas 2780 battery monitor chip"
  95         help
  96           If you enable this you will have the DS2780 battery monitor
  97           chip support.
  98
  99           The battery monitor chip is used in many batteries/devices
 100           as the one who is responsible for charging/discharging/monitoring
 101           Li+ batteries.
 102
 103           If you are unsure, say N.
 104
 105 config W1_SLAVE_DS2781
 106         tristate "Dallas 2781 battery monitor chip"
 107         help
 108           If you enable this you will have the DS2781 battery monitor
 109           chip support.
 110
 111           The battery monitor chip is used in many batteries/devices
 112           as the one who is responsible for charging/discharging/monitoring
 113           Li+ batteries.
 114
 115           If you are unsure, say N.
 116
 117 config W1_SLAVE_DS28E04
 118         tristate "4096-Bit Addressable 1-Wire EEPROM with PIO (DS28E04-100)"
 119         select CRC16
 120         help
 121           If you enable this you will have the DS28E04-100
 122           chip support.
 123
 124           Say Y here if you want to use a 1-wire
 125           4kb EEPROM with PIO family device (DS28E04).
 126
 127           If you are unsure, say N.
 128
 129 config W1_SLAVE_BQ27000
 130         tristate "BQ27000 slave support"
 131         help
 132           Say Y here if you want to use a hdq
 133           bq27000 slave support.
 134
 135 endmenu