drivers/w1/slaves/Kconfig

   1 #
   2 # 1-wire slaves configuration
   3 #
   4
   5 menu "1-wire Slaves"
   6
   7 config W1_SLAVE_THERM
   8         tristate "Thermal family implementation"
   9         help
  10           Say Y here if you want to connect 1-wire thermal sensors to your
  11           wire.
  12
  13 config W1_SLAVE_SMEM
  14         tristate "Simple 64bit memory family implementation"
  15         help
  16           Say Y here if you want to connect 1-wire
  17           simple 64bit memory rom(ds2401/ds2411/ds1990*) to your wire.
  18
  19 config W1_SLAVE_DS2408
  20         tristate "8-Channel Addressable Switch (IO Expander) 0x29 family support (DS2408)"
  21         help
  22           Say Y here if you want to use a 1-wire
  23
  24                   DS2408 8-Channel Addressable Switch device support
  25
  26 config W1_SLAVE_DS2423
  27         tristate "Counter 1-wire device (DS2423)"
  28         select CRC16
  29         help
  30           If you enable this you can read the counter values available
  31           in the DS2423 chipset from the w1_slave file under the
  32           sys file system.
  33
  34           Say Y here if you want to use a 1-wire
  35           counter family device (DS2423).
  36
  37 config W1_SLAVE_DS2431
  38         tristate "1kb EEPROM family support (DS2431)"
  39         help
  40           Say Y here if you want to use a 1-wire
  41           1kb EEPROM family device (DS2431)
  42
  43 config W1_SLAVE_DS2433
  44         tristate "4kb EEPROM family support (DS2433)"
  45         help
  46           Say Y here if you want to use a 1-wire
  47           4kb EEPROM family device (DS2433).
  48
  49 config W1_SLAVE_DS2433_CRC
  50         bool "Protect DS2433 data with a CRC16"
  51         depends on W1_SLAVE_DS2433
  52         select CRC16
  53         help
  54           Say Y here to protect DS2433 data with a CRC16.
  55           Each block has 30 bytes of data and a two byte CRC16.
  56           Full block writes are only allowed if the CRC is valid.
  57
  58 config W1_SLAVE_DS2760
  59         tristate "Dallas 2760 battery monitor chip (HP iPAQ & others)"
  60         depends on W1
  61         help
  62           If you enable this you will have the DS2760 battery monitor
  63           chip support.
  64
  65           The battery monitor chip is used in many batteries/devices
  66           as the one who is responsible for charging/discharging/monitoring
  67           Li+ batteries.
  68
  69           If you are unsure, say N.
  70
  71 config W1_SLAVE_DS2780
  72         tristate "Dallas 2780 battery monitor chip"
  73         depends on W1
  74         help
  75           If you enable this you will have the DS2780 battery monitor
  76           chip support.
  77
  78           The battery monitor chip is used in many batteries/devices
  79           as the one who is responsible for charging/discharging/monitoring
  80           Li+ batteries.
  81
  82           If you are unsure, say N.
  83
  84 config W1_SLAVE_BQ27000
  85         tristate "BQ27000 slave support"
  86         depends on W1
  87         help
  88           Say Y here if you want to use a hdq
  89           bq27000 slave support.
  90
  91 endmenu