1 @c Copyright 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2 @c 2006, 2007, 2008, 2009, 2010, 2011 Free Software Foundation, Inc.
3 @c This is part of the GAS manual.
4 @c For copying conditions, see the file as.texinfo.
9 @chapter ARM Dependent Features
13 @node Machine Dependencies
14 @chapter ARM Dependent Features
20 * ARM Options:: Options
22 * ARM Floating Point:: Floating Point
23 * ARM Directives:: ARM Machine Directives
24 * ARM Opcodes:: Opcodes
25 * ARM Mapping Symbols:: Mapping Symbols
26 * ARM Unwinding Tutorial:: Unwinding
31 @cindex ARM options (none)
32 @cindex options for ARM (none)
36 @cindex @code{-mcpu=} command line option, ARM
37 @item -mcpu=@var{processor}[+@var{extension}@dots{}]
38 This option specifies the target processor. The assembler will issue an
39 error message if an attempt is made to assemble an instruction which
40 will not execute on the target processor. The following processor names are
85 @code{fa526} (Faraday FA526 processor),
86 @code{fa626} (Faraday FA626 processor),
105 @code{fa606te} (Faraday FA606TE processor),
106 @code{fa616te} (Faraday FA616TE processor),
107 @code{fa626te} (Faraday FA626TE processor),
108 @code{fmp626} (Faraday FMP626 processor),
109 @code{fa726te} (Faraday FA726TE processor),
129 @code{cortex-m0plus},
130 @code{ep9312} (ARM920 with Cirrus Maverick coprocessor),
131 @code{i80200} (Intel XScale processor)
132 @code{iwmmxt} (Intel(r) XScale processor with Wireless MMX(tm) technology coprocessor)
135 The special name @code{all} may be used to allow the
136 assembler to accept instructions valid for any ARM processor.
138 In addition to the basic instruction set, the assembler can be told to
139 accept various extension mnemonics that extend the processor using the
140 co-processor instruction space. For example, @code{-mcpu=arm920+maverick}
141 is equivalent to specifying @code{-mcpu=ep9312}.
143 Multiple extensions may be specified, separated by a @code{+}. The
144 extensions should be specified in ascending alphabetical order.
146 Some extensions may be restricted to particular architectures; this is
147 documented in the list of extensions below.
149 Extension mnemonics may also be removed from those the assembler accepts.
150 This is done be prepending @code{no} to the option that adds the extension.
151 Extensions that are removed should be listed after all extensions which have
152 been added, again in ascending alphabetical order. For example,
153 @code{-mcpu=ep9312+nomaverick} is equivalent to specifying @code{-mcpu=arm920}.
156 The following extensions are currently supported:
157 @code{crypto} (Cryptography Extensions for v8-A architecture, implies @code{fp+simd}),
158 @code{fp} (Floating Point Extensions for v8-A architecture),
159 @code{idiv} (Integer Divide Extensions for v7-A and v7-R architectures),
163 @code{mp} (Multiprocessing Extensions for v7-A and v7-R architectures),
164 @code{os} (Operating System for v6M architecture),
165 @code{sec} (Security Extensions for v6K and v7-A architectures),
166 @code{simd} (Advanced SIMD Extensions for v8-A architecture, implies @code{fp}),
167 @code{virt} (Virtualization Extensions for v7-A architecture, implies
172 @cindex @code{-march=} command line option, ARM
173 @item -march=@var{architecture}[+@var{extension}@dots{}]
174 This option specifies the target architecture. The assembler will issue
175 an error message if an attempt is made to assemble an instruction which
176 will not execute on the target architecture. The following architecture
177 names are recognized:
209 If both @code{-mcpu} and
210 @code{-march} are specified, the assembler will use
211 the setting for @code{-mcpu}.
213 The architecture option can be extended with the same instruction set
214 extension options as the @code{-mcpu} option.
216 @cindex @code{-mfpu=} command line option, ARM
217 @item -mfpu=@var{floating-point-format}
219 This option specifies the floating point format to assemble for. The
220 assembler will issue an error message if an attempt is made to assemble
221 an instruction which will not execute on the target floating point unit.
222 The following format options are recognized:
242 @code{vfpv3-d16-fp16},
255 @code{neon-fp-armv8},
257 @code{crypto-neon-fp-armv8}.
259 In addition to determining which instructions are assembled, this option
260 also affects the way in which the @code{.double} assembler directive behaves
261 when assembling little-endian code.
263 The default is dependent on the processor selected. For Architecture 5 or
264 later, the default is to assembler for VFP instructions; for earlier
265 architectures the default is to assemble for FPA instructions.
267 @cindex @code{-mthumb} command line option, ARM
269 This option specifies that the assembler should start assembling Thumb
270 instructions; that is, it should behave as though the file starts with a
271 @code{.code 16} directive.
273 @cindex @code{-mthumb-interwork} command line option, ARM
274 @item -mthumb-interwork
275 This option specifies that the output generated by the assembler should
276 be marked as supporting interworking.
278 @cindex @code{-mimplicit-it} command line option, ARM
279 @item -mimplicit-it=never
280 @itemx -mimplicit-it=always
281 @itemx -mimplicit-it=arm
282 @itemx -mimplicit-it=thumb
283 The @code{-mimplicit-it} option controls the behavior of the assembler when
284 conditional instructions are not enclosed in IT blocks.
285 There are four possible behaviors.
286 If @code{never} is specified, such constructs cause a warning in ARM
287 code and an error in Thumb-2 code.
288 If @code{always} is specified, such constructs are accepted in both
289 ARM and Thumb-2 code, where the IT instruction is added implicitly.
290 If @code{arm} is specified, such constructs are accepted in ARM code
291 and cause an error in Thumb-2 code.
292 If @code{thumb} is specified, such constructs cause a warning in ARM
293 code and are accepted in Thumb-2 code. If you omit this option, the
294 behavior is equivalent to @code{-mimplicit-it=arm}.
296 @cindex @code{-mapcs-26} command line option, ARM
297 @cindex @code{-mapcs-32} command line option, ARM
300 These options specify that the output generated by the assembler should
301 be marked as supporting the indicated version of the Arm Procedure.
304 @cindex @code{-matpcs} command line option, ARM
306 This option specifies that the output generated by the assembler should
307 be marked as supporting the Arm/Thumb Procedure Calling Standard. If
308 enabled this option will cause the assembler to create an empty
309 debugging section in the object file called .arm.atpcs. Debuggers can
310 use this to determine the ABI being used by.
312 @cindex @code{-mapcs-float} command line option, ARM
314 This indicates the floating point variant of the APCS should be
315 used. In this variant floating point arguments are passed in FP
316 registers rather than integer registers.
318 @cindex @code{-mapcs-reentrant} command line option, ARM
319 @item -mapcs-reentrant
320 This indicates that the reentrant variant of the APCS should be used.
321 This variant supports position independent code.
323 @cindex @code{-mfloat-abi=} command line option, ARM
324 @item -mfloat-abi=@var{abi}
325 This option specifies that the output generated by the assembler should be
326 marked as using specified floating point ABI.
327 The following values are recognized:
333 @cindex @code{-eabi=} command line option, ARM
334 @item -meabi=@var{ver}
335 This option specifies which EABI version the produced object files should
337 The following values are recognized:
343 @cindex @code{-EB} command line option, ARM
345 This option specifies that the output generated by the assembler should
346 be marked as being encoded for a big-endian processor.
348 @cindex @code{-EL} command line option, ARM
350 This option specifies that the output generated by the assembler should
351 be marked as being encoded for a little-endian processor.
353 @cindex @code{-k} command line option, ARM
354 @cindex PIC code generation for ARM
356 This option specifies that the output of the assembler should be marked
357 as position-independent code (PIC).
359 @cindex @code{--fix-v4bx} command line option, ARM
361 Allow @code{BX} instructions in ARMv4 code. This is intended for use with
362 the linker option of the same name.
364 @cindex @code{-mwarn-deprecated} command line option, ARM
365 @item -mwarn-deprecated
366 @itemx -mno-warn-deprecated
367 Enable or disable warnings about using deprecated options or
368 features. The default is to warn.
376 * ARM-Instruction-Set:: Instruction Set
377 * ARM-Chars:: Special Characters
378 * ARM-Regs:: Register Names
379 * ARM-Relocations:: Relocations
380 * ARM-Neon-Alignment:: NEON Alignment Specifiers
383 @node ARM-Instruction-Set
384 @subsection Instruction Set Syntax
385 Two slightly different syntaxes are support for ARM and THUMB
386 instructions. The default, @code{divided}, uses the old style where
387 ARM and THUMB instructions had their own, separate syntaxes. The new,
388 @code{unified} syntax, which can be selected via the @code{.syntax}
389 directive, and has the following main features:
393 Immediate operands do not require a @code{#} prefix.
396 The @code{IT} instruction may appear, and if it does it is validated
397 against subsequent conditional affixes. In ARM mode it does not
398 generate machine code, in THUMB mode it does.
401 For ARM instructions the conditional affixes always appear at the end
402 of the instruction. For THUMB instructions conditional affixes can be
403 used, but only inside the scope of an @code{IT} instruction.
406 All of the instructions new to the V6T2 architecture (and later) are
407 available. (Only a few such instructions can be written in the
408 @code{divided} syntax).
411 The @code{.N} and @code{.W} suffixes are recognized and honored.
414 All instructions set the flags if and only if they have an @code{s}
419 @subsection Special Characters
421 @cindex line comment character, ARM
422 @cindex ARM line comment character
423 The presence of a @samp{@@} anywhere on a line indicates the start of
424 a comment that extends to the end of that line.
426 If a @samp{#} appears as the first character of a line then the whole
427 line is treated as a comment, but in this case the line could also be
428 a logical line number directive (@pxref{Comments}) or a preprocessor
429 control command (@pxref{Preprocessing}).
431 @cindex line separator, ARM
432 @cindex statement separator, ARM
433 @cindex ARM line separator
434 The @samp{;} character can be used instead of a newline to separate
437 @cindex immediate character, ARM
438 @cindex ARM immediate character
439 Either @samp{#} or @samp{$} can be used to indicate immediate operands.
441 @cindex identifiers, ARM
442 @cindex ARM identifiers
443 *TODO* Explain about /data modifier on symbols.
446 @subsection Register Names
448 @cindex ARM register names
449 @cindex register names, ARM
450 *TODO* Explain about ARM register naming, and the predefined names.
452 @node ARM-Neon-Alignment
453 @subsection NEON Alignment Specifiers
455 @cindex alignment for NEON instructions
456 Some NEON load/store instructions allow an optional address
458 The ARM documentation specifies that this is indicated by
459 @samp{@@ @var{align}}. However GAS already interprets
460 the @samp{@@} character as a "line comment" start,
461 so @samp{: @var{align}} is used instead. For example:
464 vld1.8 @{q0@}, [r0, :128]
467 @node ARM Floating Point
468 @section Floating Point
470 @cindex floating point, ARM (@sc{ieee})
471 @cindex ARM floating point (@sc{ieee})
472 The ARM family uses @sc{ieee} floating-point numbers.
474 @node ARM-Relocations
475 @subsection ARM relocation generation
477 @cindex data relocations, ARM
478 @cindex ARM data relocations
479 Specific data relocations can be generated by putting the relocation name
480 in parentheses after the symbol name. For example:
486 This will generate an @samp{R_ARM_TARGET1} relocation against the symbol
488 The following relocations are supported:
504 For compatibility with older toolchains the assembler also accepts
505 @code{(PLT)} after branch targets. On legacy targets this will
506 generate the deprecated @samp{R_ARM_PLT32} relocation. On EABI
507 targets it will encode either the @samp{R_ARM_CALL} or
508 @samp{R_ARM_JUMP24} relocation, as appropriate.
510 @cindex MOVW and MOVT relocations, ARM
511 Relocations for @samp{MOVW} and @samp{MOVT} instructions can be generated
512 by prefixing the value with @samp{#:lower16:} and @samp{#:upper16}
513 respectively. For example to load the 32-bit address of foo into r0:
516 MOVW r0, #:lower16:foo
517 MOVT r0, #:upper16:foo
521 @section ARM Machine Directives
523 @cindex machine directives, ARM
524 @cindex ARM machine directives
527 @c AAAAAAAAAAAAAAAAAAAAAAAAA
529 @cindex @code{.2byte} directive, ARM
530 @cindex @code{.4byte} directive, ARM
531 @cindex @code{.8byte} directive, ARM
532 @item .2byte @var{expression} [, @var{expression}]*
533 @itemx .4byte @var{expression} [, @var{expression}]*
534 @itemx .8byte @var{expression} [, @var{expression}]*
535 These directives write 2, 4 or 8 byte values to the output section.
537 @cindex @code{.align} directive, ARM
538 @item .align @var{expression} [, @var{expression}]
539 This is the generic @var{.align} directive. For the ARM however if the
540 first argument is zero (ie no alignment is needed) the assembler will
541 behave as if the argument had been 2 (ie pad to the next four byte
542 boundary). This is for compatibility with ARM's own assembler.
544 @cindex @code{.arch} directive, ARM
545 @item .arch @var{name}
546 Select the target architecture. Valid values for @var{name} are the same as
547 for the @option{-march} commandline option.
549 Specifying @code{.arch} clears any previously selected architecture
552 @cindex @code{.arch_extension} directive, ARM
553 @item .arch_extension @var{name}
554 Add or remove an architecture extension to the target architecture. Valid
555 values for @var{name} are the same as those accepted as architectural
556 extensions by the @option{-mcpu} commandline option.
558 @code{.arch_extension} may be used multiple times to add or remove extensions
559 incrementally to the architecture being compiled for.
561 @cindex @code{.arm} directive, ARM
563 This performs the same action as @var{.code 32}.
566 @cindex @code{.pad} directive, ARM
567 @item .pad #@var{count}
568 Generate unwinder annotations for a stack adjustment of @var{count} bytes.
569 A positive value indicates the function prologue allocated stack space by
570 decrementing the stack pointer.
572 @c BBBBBBBBBBBBBBBBBBBBBBBBBB
574 @cindex @code{.bss} directive, ARM
576 This directive switches to the @code{.bss} section.
578 @c CCCCCCCCCCCCCCCCCCCCCCCCCC
580 @cindex @code{.cantunwind} directive, ARM
582 Prevents unwinding through the current function. No personality routine
583 or exception table data is required or permitted.
585 @cindex @code{.code} directive, ARM
586 @item .code @code{[16|32]}
587 This directive selects the instruction set being generated. The value 16
588 selects Thumb, with the value 32 selecting ARM.
590 @cindex @code{.cpu} directive, ARM
591 @item .cpu @var{name}
592 Select the target processor. Valid values for @var{name} are the same as
593 for the @option{-mcpu} commandline option.
595 Specifying @code{.cpu} clears any previously selected architecture
598 @c DDDDDDDDDDDDDDDDDDDDDDDDDD
600 @cindex @code{.dn} and @code{.qn} directives, ARM
601 @item @var{name} .dn @var{register name} [@var{.type}] [[@var{index}]]
602 @itemx @var{name} .qn @var{register name} [@var{.type}] [[@var{index}]]
604 The @code{dn} and @code{qn} directives are used to create typed
605 and/or indexed register aliases for use in Advanced SIMD Extension
606 (Neon) instructions. The former should be used to create aliases
607 of double-precision registers, and the latter to create aliases of
608 quad-precision registers.
610 If these directives are used to create typed aliases, those aliases can
611 be used in Neon instructions instead of writing types after the mnemonic
612 or after each operand. For example:
621 This is equivalent to writing the following:
627 Aliases created using @code{dn} or @code{qn} can be destroyed using
630 @c EEEEEEEEEEEEEEEEEEEEEEEEEE
632 @cindex @code{.eabi_attribute} directive, ARM
633 @item .eabi_attribute @var{tag}, @var{value}
634 Set the EABI object attribute @var{tag} to @var{value}.
636 The @var{tag} is either an attribute number, or one of the following:
637 @code{Tag_CPU_raw_name}, @code{Tag_CPU_name}, @code{Tag_CPU_arch},
638 @code{Tag_CPU_arch_profile}, @code{Tag_ARM_ISA_use},
639 @code{Tag_THUMB_ISA_use}, @code{Tag_FP_arch}, @code{Tag_WMMX_arch},
640 @code{Tag_Advanced_SIMD_arch}, @code{Tag_PCS_config},
641 @code{Tag_ABI_PCS_R9_use}, @code{Tag_ABI_PCS_RW_data},
642 @code{Tag_ABI_PCS_RO_data}, @code{Tag_ABI_PCS_GOT_use},
643 @code{Tag_ABI_PCS_wchar_t}, @code{Tag_ABI_FP_rounding},
644 @code{Tag_ABI_FP_denormal}, @code{Tag_ABI_FP_exceptions},
645 @code{Tag_ABI_FP_user_exceptions}, @code{Tag_ABI_FP_number_model},
646 @code{Tag_ABI_align_needed}, @code{Tag_ABI_align_preserved},
647 @code{Tag_ABI_enum_size}, @code{Tag_ABI_HardFP_use},
648 @code{Tag_ABI_VFP_args}, @code{Tag_ABI_WMMX_args},
649 @code{Tag_ABI_optimization_goals}, @code{Tag_ABI_FP_optimization_goals},
650 @code{Tag_compatibility}, @code{Tag_CPU_unaligned_access},
651 @code{Tag_FP_HP_extension}, @code{Tag_ABI_FP_16bit_format},
652 @code{Tag_MPextension_use}, @code{Tag_DIV_use},
653 @code{Tag_nodefaults}, @code{Tag_also_compatible_with},
654 @code{Tag_conformance}, @code{Tag_T2EE_use},
655 @code{Tag_Virtualization_use}
657 The @var{value} is either a @code{number}, @code{"string"}, or
658 @code{number, "string"} depending on the tag.
660 Note - the following legacy values are also accepted by @var{tag}:
661 @code{Tag_VFP_arch}, @code{Tag_ABI_align8_needed},
662 @code{Tag_ABI_align8_preserved}, @code{Tag_VFP_HP_extension},
664 @cindex @code{.even} directive, ARM
666 This directive aligns to an even-numbered address.
668 @cindex @code{.extend} directive, ARM
669 @cindex @code{.ldouble} directive, ARM
670 @item .extend @var{expression} [, @var{expression}]*
671 @itemx .ldouble @var{expression} [, @var{expression}]*
672 These directives write 12byte long double floating-point values to the
673 output section. These are not compatible with current ARM processors
676 @c FFFFFFFFFFFFFFFFFFFFFFFFFF
679 @cindex @code{.fnend} directive, ARM
681 Marks the end of a function with an unwind table entry. The unwind index
682 table entry is created when this directive is processed.
684 If no personality routine has been specified then standard personality
685 routine 0 or 1 will be used, depending on the number of unwind opcodes
689 @cindex @code{.fnstart} directive, ARM
691 Marks the start of a function with an unwind table entry.
693 @cindex @code{.force_thumb} directive, ARM
695 This directive forces the selection of Thumb instructions, even if the
696 target processor does not support those instructions
698 @cindex @code{.fpu} directive, ARM
699 @item .fpu @var{name}
700 Select the floating-point unit to assemble for. Valid values for @var{name}
701 are the same as for the @option{-mfpu} commandline option.
703 @c GGGGGGGGGGGGGGGGGGGGGGGGGG
704 @c HHHHHHHHHHHHHHHHHHHHHHHHHH
706 @cindex @code{.handlerdata} directive, ARM
708 Marks the end of the current function, and the start of the exception table
709 entry for that function. Anything between this directive and the
710 @code{.fnend} directive will be added to the exception table entry.
712 Must be preceded by a @code{.personality} or @code{.personalityindex}
715 @c IIIIIIIIIIIIIIIIIIIIIIIIII
717 @cindex @code{.inst} directive, ARM
718 @item .inst @var{opcode} [ , @dots{} ]
719 @itemx .inst.n @var{opcode} [ , @dots{} ]
720 @itemx .inst.w @var{opcode} [ , @dots{} ]
721 Generates the instruction corresponding to the numerical value @var{opcode}.
722 @code{.inst.n} and @code{.inst.w} allow the Thumb instruction size to be
723 specified explicitly, overriding the normal encoding rules.
725 @c JJJJJJJJJJJJJJJJJJJJJJJJJJ
726 @c KKKKKKKKKKKKKKKKKKKKKKKKKK
727 @c LLLLLLLLLLLLLLLLLLLLLLLLLL
729 @item .ldouble @var{expression} [, @var{expression}]*
732 @cindex @code{.ltorg} directive, ARM
734 This directive causes the current contents of the literal pool to be
735 dumped into the current section (which is assumed to be the .text
736 section) at the current location (aligned to a word boundary).
737 @code{GAS} maintains a separate literal pool for each section and each
738 sub-section. The @code{.ltorg} directive will only affect the literal
739 pool of the current section and sub-section. At the end of assembly
740 all remaining, un-empty literal pools will automatically be dumped.
742 Note - older versions of @code{GAS} would dump the current literal
743 pool any time a section change occurred. This is no longer done, since
744 it prevents accurate control of the placement of literal pools.
746 @c MMMMMMMMMMMMMMMMMMMMMMMMMM
748 @cindex @code{.movsp} directive, ARM
749 @item .movsp @var{reg} [, #@var{offset}]
750 Tell the unwinder that @var{reg} contains an offset from the current
751 stack pointer. If @var{offset} is not specified then it is assumed to be
754 @c NNNNNNNNNNNNNNNNNNNNNNNNNN
755 @c OOOOOOOOOOOOOOOOOOOOOOOOOO
757 @cindex @code{.object_arch} directive, ARM
758 @item .object_arch @var{name}
759 Override the architecture recorded in the EABI object attribute section.
760 Valid values for @var{name} are the same as for the @code{.arch} directive.
761 Typically this is useful when code uses runtime detection of CPU features.
763 @c PPPPPPPPPPPPPPPPPPPPPPPPPP
765 @cindex @code{.packed} directive, ARM
766 @item .packed @var{expression} [, @var{expression}]*
767 This directive writes 12-byte packed floating-point values to the
768 output section. These are not compatible with current ARM processors
771 @cindex @code{.pad} directive, ARM
772 @item .pad #@var{count}
773 Generate unwinder annotations for a stack adjustment of @var{count} bytes.
774 A positive value indicates the function prologue allocated stack space by
775 decrementing the stack pointer.
777 @cindex @code{.personality} directive, ARM
778 @item .personality @var{name}
779 Sets the personality routine for the current function to @var{name}.
781 @cindex @code{.personalityindex} directive, ARM
782 @item .personalityindex @var{index}
783 Sets the personality routine for the current function to the EABI standard
784 routine number @var{index}
786 @cindex @code{.pool} directive, ARM
788 This is a synonym for .ltorg.
790 @c QQQQQQQQQQQQQQQQQQQQQQQQQQ
791 @c RRRRRRRRRRRRRRRRRRRRRRRRRR
793 @cindex @code{.req} directive, ARM
794 @item @var{name} .req @var{register name}
795 This creates an alias for @var{register name} called @var{name}. For
802 @c SSSSSSSSSSSSSSSSSSSSSSSSSS
805 @cindex @code{.save} directive, ARM
806 @item .save @var{reglist}
807 Generate unwinder annotations to restore the registers in @var{reglist}.
808 The format of @var{reglist} is the same as the corresponding store-multiple
812 @exdent @emph{core registers}
813 .save @{r4, r5, r6, lr@}
814 stmfd sp!, @{r4, r5, r6, lr@}
815 @exdent @emph{FPA registers}
818 @exdent @emph{VFP registers}
819 .save @{d8, d9, d10@}
820 fstmdx sp!, @{d8, d9, d10@}
821 @exdent @emph{iWMMXt registers}
823 wstrd wr11, [sp, #-8]!
824 wstrd wr10, [sp, #-8]!
827 wstrd wr11, [sp, #-8]!
829 wstrd wr10, [sp, #-8]!
833 @cindex @code{.setfp} directive, ARM
834 @item .setfp @var{fpreg}, @var{spreg} [, #@var{offset}]
835 Make all unwinder annotations relative to a frame pointer. Without this
836 the unwinder will use offsets from the stack pointer.
838 The syntax of this directive is the same as the @code{add} or @code{mov}
839 instruction used to set the frame pointer. @var{spreg} must be either
840 @code{sp} or mentioned in a previous @code{.movsp} directive.
850 @cindex @code{.secrel32} directive, ARM
851 @item .secrel32 @var{expression} [, @var{expression}]*
852 This directive emits relocations that evaluate to the section-relative
853 offset of each expression's symbol. This directive is only supported
856 @cindex @code{.syntax} directive, ARM
857 @item .syntax [@code{unified} | @code{divided}]
858 This directive sets the Instruction Set Syntax as described in the
859 @ref{ARM-Instruction-Set} section.
861 @c TTTTTTTTTTTTTTTTTTTTTTTTTT
863 @cindex @code{.thumb} directive, ARM
865 This performs the same action as @var{.code 16}.
867 @cindex @code{.thumb_func} directive, ARM
869 This directive specifies that the following symbol is the name of a
870 Thumb encoded function. This information is necessary in order to allow
871 the assembler and linker to generate correct code for interworking
872 between Arm and Thumb instructions and should be used even if
873 interworking is not going to be performed. The presence of this
874 directive also implies @code{.thumb}
876 This directive is not neccessary when generating EABI objects. On these
877 targets the encoding is implicit when generating Thumb code.
879 @cindex @code{.thumb_set} directive, ARM
881 This performs the equivalent of a @code{.set} directive in that it
882 creates a symbol which is an alias for another symbol (possibly not yet
883 defined). This directive also has the added property in that it marks
884 the aliased symbol as being a thumb function entry point, in the same
885 way that the @code{.thumb_func} directive does.
887 @cindex @code{.tlsdescseq} directive, ARM
888 @item .tlsdescseq @var{tls-variable}
889 This directive is used to annotate parts of an inlined TLS descriptor
890 trampoline. Normally the trampoline is provided by the linker, and
891 this directive is not needed.
893 @c UUUUUUUUUUUUUUUUUUUUUUUUUU
895 @cindex @code{.unreq} directive, ARM
896 @item .unreq @var{alias-name}
897 This undefines a register alias which was previously defined using the
898 @code{req}, @code{dn} or @code{qn} directives. For example:
905 An error occurs if the name is undefined. Note - this pseudo op can
906 be used to delete builtin in register name aliases (eg 'r0'). This
907 should only be done if it is really necessary.
909 @cindex @code{.unwind_raw} directive, ARM
910 @item .unwind_raw @var{offset}, @var{byte1}, @dots{}
911 Insert one of more arbitary unwind opcode bytes, which are known to adjust
912 the stack pointer by @var{offset} bytes.
914 For example @code{.unwind_raw 4, 0xb1, 0x01} is equivalent to
917 @c VVVVVVVVVVVVVVVVVVVVVVVVVV
919 @cindex @code{.vsave} directive, ARM
920 @item .vsave @var{vfp-reglist}
921 Generate unwinder annotations to restore the VFP registers in @var{vfp-reglist}
922 using FLDMD. Also works for VFPv3 registers
923 that are to be restored using VLDM.
924 The format of @var{vfp-reglist} is the same as the corresponding store-multiple
928 @exdent @emph{VFP registers}
929 .vsave @{d8, d9, d10@}
930 fstmdd sp!, @{d8, d9, d10@}
931 @exdent @emph{VFPv3 registers}
932 .vsave @{d15, d16, d17@}
933 vstm sp!, @{d15, d16, d17@}
936 Since FLDMX and FSTMX are now deprecated, this directive should be
937 used in favour of @code{.save} for saving VFP registers for ARMv6 and above.
939 @c WWWWWWWWWWWWWWWWWWWWWWWWWW
940 @c XXXXXXXXXXXXXXXXXXXXXXXXXX
941 @c YYYYYYYYYYYYYYYYYYYYYYYYYY
942 @c ZZZZZZZZZZZZZZZZZZZZZZZZZZ
950 @cindex opcodes for ARM
951 @code{@value{AS}} implements all the standard ARM opcodes. It also
952 implements several pseudo opcodes, including several synthetic load
957 @cindex @code{NOP} pseudo op, ARM
963 This pseudo op will always evaluate to a legal ARM instruction that does
964 nothing. Currently it will evaluate to MOV r0, r0.
966 @cindex @code{LDR reg,=<label>} pseudo op, ARM
969 ldr <register> , = <expression>
972 If expression evaluates to a numeric constant then a MOV or MVN
973 instruction will be used in place of the LDR instruction, if the
974 constant can be generated by either of these instructions. Otherwise
975 the constant will be placed into the nearest literal pool (if it not
976 already there) and a PC relative LDR instruction will be generated.
978 @cindex @code{ADR reg,<label>} pseudo op, ARM
981 adr <register> <label>
984 This instruction will load the address of @var{label} into the indicated
985 register. The instruction will evaluate to a PC relative ADD or SUB
986 instruction depending upon where the label is located. If the label is
987 out of range, or if it is not defined in the same file (and section) as
988 the ADR instruction, then an error will be generated. This instruction
989 will not make use of the literal pool.
991 @cindex @code{ADRL reg,<label>} pseudo op, ARM
994 adrl <register> <label>
997 This instruction will load the address of @var{label} into the indicated
998 register. The instruction will evaluate to one or two PC relative ADD
999 or SUB instructions depending upon where the label is located. If a
1000 second instruction is not needed a NOP instruction will be generated in
1001 its place, so that this instruction is always 8 bytes long.
1003 If the label is out of range, or if it is not defined in the same file
1004 (and section) as the ADRL instruction, then an error will be generated.
1005 This instruction will not make use of the literal pool.
1009 For information on the ARM or Thumb instruction sets, see @cite{ARM
1010 Software Development Toolkit Reference Manual}, Advanced RISC Machines
1013 @node ARM Mapping Symbols
1014 @section Mapping Symbols
1016 The ARM ELF specification requires that special symbols be inserted
1017 into object files to mark certain features:
1023 At the start of a region of code containing ARM instructions.
1027 At the start of a region of code containing THUMB instructions.
1031 At the start of a region of data.
1035 The assembler will automatically insert these symbols for you - there
1036 is no need to code them yourself. Support for tagging symbols ($b,
1037 $f, $p and $m) which is also mentioned in the current ARM ELF
1038 specification is not implemented. This is because they have been
1039 dropped from the new EABI and so tools cannot rely upon their
1042 @node ARM Unwinding Tutorial
1045 The ABI for the ARM Architecture specifies a standard format for
1046 exception unwind information. This information is used when an
1047 exception is thrown to determine where control should be transferred.
1048 In particular, the unwind information is used to determine which
1049 function called the function that threw the exception, and which
1050 function called that one, and so forth. This information is also used
1051 to restore the values of callee-saved registers in the function
1052 catching the exception.
1054 If you are writing functions in assembly code, and those functions
1055 call other functions that throw exceptions, you must use assembly
1056 pseudo ops to ensure that appropriate exception unwind information is
1057 generated. Otherwise, if one of the functions called by your assembly
1058 code throws an exception, the run-time library will be unable to
1059 unwind the stack through your assembly code and your program will not
1062 To illustrate the use of these pseudo ops, we will examine the code
1063 that G++ generates for the following C++ input:
1066 void callee (int *);
1077 This example does not show how to throw or catch an exception from
1078 assembly code. That is a much more complex operation and should
1079 always be done in a high-level language, such as C++, that directly
1080 supports exceptions.
1082 The code generated by one particular version of G++ when compiling the
1089 @ Function supports interworking.
1090 @ args = 0, pretend = 0, frame = 8
1091 @ frame_needed = 1, uses_anonymous_args = 0
1113 Of course, the sequence of instructions varies based on the options
1114 you pass to GCC and on the version of GCC in use. The exact
1115 instructions are not important since we are focusing on the pseudo ops
1116 that are used to generate unwind information.
1118 An important assumption made by the unwinder is that the stack frame
1119 does not change during the body of the function. In particular, since
1120 we assume that the assembly code does not itself throw an exception,
1121 the only point where an exception can be thrown is from a call, such
1122 as the @code{bl} instruction above. At each call site, the same saved
1123 registers (including @code{lr}, which indicates the return address)
1124 must be located in the same locations relative to the frame pointer.
1126 The @code{.fnstart} (@pxref{arm_fnstart,,.fnstart pseudo op}) pseudo
1127 op appears immediately before the first instruction of the function
1128 while the @code{.fnend} (@pxref{arm_fnend,,.fnend pseudo op}) pseudo
1129 op appears immediately after the last instruction of the function.
1130 These pseudo ops specify the range of the function.
1132 Only the order of the other pseudos ops (e.g., @code{.setfp} or
1133 @code{.pad}) matters; their exact locations are irrelevant. In the
1134 example above, the compiler emits the pseudo ops with particular
1135 instructions. That makes it easier to understand the code, but it is
1136 not required for correctness. It would work just as well to emit all
1137 of the pseudo ops other than @code{.fnend} in the same order, but
1138 immediately after @code{.fnstart}.
1140 The @code{.save} (@pxref{arm_save,,.save pseudo op}) pseudo op
1141 indicates registers that have been saved to the stack so that they can
1142 be restored before the function returns. The argument to the
1143 @code{.save} pseudo op is a list of registers to save. If a register
1144 is ``callee-saved'' (as specified by the ABI) and is modified by the
1145 function you are writing, then your code must save the value before it
1146 is modified and restore the original value before the function
1147 returns. If an exception is thrown, the run-time library restores the
1148 values of these registers from their locations on the stack before
1149 returning control to the exception handler. (Of course, if an
1150 exception is not thrown, the function that contains the @code{.save}
1151 pseudo op restores these registers in the function epilogue, as is
1152 done with the @code{ldmfd} instruction above.)
1154 You do not have to save callee-saved registers at the very beginning
1155 of the function and you do not need to use the @code{.save} pseudo op
1156 immediately following the point at which the registers are saved.
1157 However, if you modify a callee-saved register, you must save it on
1158 the stack before modifying it and before calling any functions which
1159 might throw an exception. And, you must use the @code{.save} pseudo
1160 op to indicate that you have done so.
1162 The @code{.pad} (@pxref{arm_pad,,.pad}) pseudo op indicates a
1163 modification of the stack pointer that does not save any registers.
1164 The argument is the number of bytes (in decimal) that are subtracted
1165 from the stack pointer. (On ARM CPUs, the stack grows downwards, so
1166 subtracting from the stack pointer increases the size of the stack.)
1168 The @code{.setfp} (@pxref{arm_setfp,,.setfp pseudo op}) pseudo op
1169 indicates the register that contains the frame pointer. The first
1170 argument is the register that is set, which is typically @code{fp}.
1171 The second argument indicates the register from which the frame
1172 pointer takes its value. The third argument, if present, is the value
1173 (in decimal) added to the register specified by the second argument to
1174 compute the value of the frame pointer. You should not modify the
1175 frame pointer in the body of the function.
1177 If you do not use a frame pointer, then you should not use the
1178 @code{.setfp} pseudo op. If you do not use a frame pointer, then you
1179 should avoid modifying the stack pointer outside of the function
1180 prologue. Otherwise, the run-time library will be unable to find
1181 saved registers when it is unwinding the stack.
1183 The pseudo ops described above are sufficient for writing assembly
1184 code that calls functions which may throw exceptions. If you need to
1185 know more about the object-file format used to represent unwind
1186 information, you may consult the @cite{Exception Handling ABI for the
1187 ARM Architecture} available from @uref{http://infocenter.arm.com}.