1 /* sh-stub.c -- debugging stub for the Renesas-SH.
3 NOTE!! This code has to be compiled with optimization, otherwise the
4 function inlining which generates the exception handlers won't work.
8 /* This is originally based on an m68k software stub written by Glenn
9 Engel at HP, but has changed quite a bit.
11 Modifications for the SH by Ben Lee and Steve Chamberlain
15 /****************************************************************************
17 THIS SOFTWARE IS NOT COPYRIGHTED
19 HP offers the following for use in the public domain. HP makes no
20 warranty with regard to the software or it's performance and the
21 user accepts the software "AS IS" with all faults.
23 HP DISCLAIMS ANY WARRANTIES, EXPRESS OR IMPLIED, WITH REGARD
24 TO THIS SOFTWARE INCLUDING BUT NOT LIMITED TO THE WARRANTIES
25 OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
27 ****************************************************************************/
30 /* Remote communication protocol.
32 A debug packet whose contents are <data>
33 is encapsulated for transmission in the form:
35 $ <data> # CSUM1 CSUM2
37 <data> must be ASCII alphanumeric and cannot include characters
38 '$' or '#'. If <data> starts with two characters followed by
39 ':', then the existing stubs interpret this as a sequence number.
41 CSUM1 and CSUM2 are ascii hex representation of an 8-bit
42 checksum of <data>, the most significant nibble is sent first.
43 the hex digits 0-9,a-f are used.
45 Receiver responds with:
47 + - if CSUM is correct and ready for next packet
48 - - if CSUM is incorrect
51 All values are encoded in ascii hex digits.
56 reply XX....X Each byte of register data
57 is described by two hex digits.
58 Registers are in the internal order
59 for GDB, and the bytes in a register
60 are in the same order the machine uses.
63 write regs GXX..XX Each byte of register data
64 is described by two hex digits.
68 write reg Pn...=r... Write register n... with value r...,
69 which contains two hex digits for each
70 byte in the register (target byte
74 (not supported by all stubs).
76 read mem mAA..AA,LLLL AA..AA is address, LLLL is length.
77 reply XX..XX XX..XX is mem contents
78 Can be fewer bytes than requested
79 if able to read only part of the data.
82 write mem MAA..AA,LLLL:XX..XX
84 LLLL is number of bytes,
87 ENN for an error (this includes the case
88 where only part of the data was
91 cont cAA..AA AA..AA is address to resume
93 resume at same address.
95 step sAA..AA AA..AA is address to resume
97 resume at same address.
99 last signal ? Reply the current reason for stopping.
100 This is the same reply as is generated
101 for step or cont : SAA where AA is the
104 There is no immediate reply to step or cont.
105 The reply comes when the machine stops.
106 It is SAA AA is the "signal number"
108 or... TAAn...:r...;n:r...;n...:r...;
110 n... = register number
111 r... = register contents
112 or... WAA The process exited, and AA is
113 the exit status. This is only
114 applicable for certains sorts of
118 toggle debug d toggle debug flag (see 386 & 68k stubs)
119 reset r reset -- see sparc stub.
120 reserved <other> On other requests, the stub should
121 ignore the request and send an empty
122 response ($#<checksum>). This way
123 we can extend the protocol and GDB
124 can tell whether the stub it is
125 talking to uses the old or the new.
126 search tAA:PP,MM Search backwards starting at address
127 AA for a match with pattern PP and
128 mask MM. PP and MM are 4 bytes.
129 Not supported by all stubs.
131 general query qXXXX Request info about XXXX.
132 general set QXXXX=yyyy Set value of XXXX to yyyy.
133 query sect offs qOffsets Get section offsets. Reply is
134 Text=xxx;Data=yyy;Bss=zzz
135 console output Otext Send text to stdout. Only comes from
138 Responses can be run-length encoded to save space. A '*' means that
139 the next character is an ASCII encoding giving a repeat count which
140 stands for that many repititions of the character preceding the '*'.
141 The encoding is n+29, yielding a printable character where n >=3
142 (which is where rle starts to win). Don't use an n > 126.
145 "0* " means the same as "0000". */
150 /* Renesas SH architecture instruction encoding masks */
152 #define COND_BR_MASK 0xff00
153 #define UCOND_DBR_MASK 0xe000
154 #define UCOND_RBR_MASK 0xf0df
155 #define TRAPA_MASK 0xff00
157 #define COND_DISP 0x00ff
158 #define UCOND_DISP 0x0fff
159 #define UCOND_REG 0x0f00
161 /* Renesas SH instruction opcodes */
163 #define BF_INSTR 0x8b00
164 #define BT_INSTR 0x8900
165 #define BRA_INSTR 0xa000
166 #define BSR_INSTR 0xb000
167 #define JMP_INSTR 0x402b
168 #define JSR_INSTR 0x400b
169 #define RTS_INSTR 0x000b
170 #define RTE_INSTR 0x002b
171 #define TRAPA_INSTR 0xc300
172 #define SSTEP_INSTR 0xc3ff
174 /* Renesas SH processor register masks */
176 #define T_BIT_MASK 0x0001
179 * BUFMAX defines the maximum number of characters in inbound/outbound
180 * buffers. At least NUMREGBYTES*2 are needed for register packets.
185 * Number of bytes for registers
187 #define NUMREGBYTES 112 /* 92 */
192 typedef void (*Function
) ();
195 * Forward declarations
198 static int hex (char);
199 static char *mem2hex (char *, char *, int);
200 static char *hex2mem (char *, char *, int);
201 static int hexToInt (char **, int *);
202 static unsigned char *getpacket (void);
203 static void putpacket (char *);
204 static void handle_buserror (void);
205 static int computeSignal (int exceptionVector
);
206 static void handle_exception (int exceptionVector
);
209 void putDebugChar (char);
210 char getDebugChar (void);
212 /* These are in the file but in asm statements so the compiler can't see them */
213 void catch_exception_4 (void);
214 void catch_exception_6 (void);
215 void catch_exception_9 (void);
216 void catch_exception_10 (void);
217 void catch_exception_11 (void);
218 void catch_exception_32 (void);
219 void catch_exception_33 (void);
220 void catch_exception_255 (void);
224 #define catch_exception_random catch_exception_255 /* Treat all odd ones like 255 */
226 void breakpoint (void);
229 #define init_stack_size 8*1024 /* if you change this you should also modify BINIT */
230 #define stub_stack_size 8*1024
232 int init_stack
[init_stack_size
] __attribute__ ((section ("stack"))) = {0};
233 int stub_stack
[stub_stack_size
] __attribute__ ((section ("stack"))) = {0};
239 #define CPU_BUS_ERROR_VEC 9
240 #define DMA_BUS_ERROR_VEC 10
242 #define INVALID_INSN_VEC 4
243 #define INVALID_SLOT_VEC 6
250 char in_nmi
; /* Set when handling an NMI, so we don't reenter */
251 int dofault
; /* Non zero, bus errors will raise exception */
255 /* debug > 0 prints ill-formed commands in valid packets & checksum errors */
258 /* jump buffer used for setjmp/longjmp */
263 R0
, R1
, R2
, R3
, R4
, R5
, R6
, R7
,
264 R8
, R9
, R10
, R11
, R12
, R13
, R14
,
265 R15
, PC
, PR
, GBR
, VBR
, MACH
, MACL
, SR
,
266 TICKS
, STALLS
, CYCLES
, INSTS
, PLR
276 int registers
[NUMREGBYTES
/ 4];
277 stepData instrBuffer
;
279 static const char hexchars
[] = "0123456789abcdef";
280 static char remcomInBuffer
[BUFMAX
];
281 static char remcomOutBuffer
[BUFMAX
];
285 return hexchars
[(x
>> 4) & 0xf];
290 return hexchars
[x
& 0xf];
297 #define BREAKPOINT() asm("trapa #0x20"::);
301 * Routines to handle hex data
307 if ((ch
>= 'a') && (ch
<= 'f'))
308 return (ch
- 'a' + 10);
309 if ((ch
>= '0') && (ch
<= '9'))
311 if ((ch
>= 'A') && (ch
<= 'F'))
312 return (ch
- 'A' + 10);
316 /* convert the memory, pointed to by mem into hex, placing result in buf */
317 /* return a pointer to the last char put in buf (null) */
319 mem2hex (char *mem
, char *buf
, int count
)
323 for (i
= 0; i
< count
; i
++)
326 *buf
++ = highhex (ch
);
327 *buf
++ = lowhex (ch
);
333 /* convert the hex array pointed to by buf into binary, to be placed in mem */
334 /* return a pointer to the character after the last byte written */
337 hex2mem (char *buf
, char *mem
, int count
)
341 for (i
= 0; i
< count
; i
++)
343 ch
= hex (*buf
++) << 4;
344 ch
= ch
+ hex (*buf
++);
350 /**********************************************/
351 /* WHILE WE FIND NICE HEX CHARS, BUILD AN INT */
352 /* RETURN NUMBER OF CHARS PROCESSED */
353 /**********************************************/
355 hexToInt (char **ptr
, int *intValue
)
364 hexValue
= hex (**ptr
);
367 *intValue
= (*intValue
<< 4) | hexValue
;
380 * Routines to get and put packets
383 /* scan for the sequence $<data>#<checksum> */
388 unsigned char *buffer
= &remcomInBuffer
[0];
389 unsigned char checksum
;
390 unsigned char xmitcsum
;
396 /* wait around for the start character, ignore all other characters */
397 while ((ch
= getDebugChar ()) != '$')
405 /* now, read until a # or end of buffer is found */
406 while (count
< BUFMAX
- 1)
408 ch
= getDebugChar ();
413 checksum
= checksum
+ ch
;
421 ch
= getDebugChar ();
422 xmitcsum
= hex (ch
) << 4;
423 ch
= getDebugChar ();
424 xmitcsum
+= hex (ch
);
426 if (checksum
!= xmitcsum
)
428 putDebugChar ('-'); /* failed checksum */
432 putDebugChar ('+'); /* successful transfer */
434 /* if a sequence char is present, reply the sequence ID */
435 if (buffer
[2] == ':')
437 putDebugChar (buffer
[0]);
438 putDebugChar (buffer
[1]);
450 /* send the packet in buffer. */
453 putpacket (char *buffer
)
458 /* $<packet info>#<checksum>. */
469 /* Do run length encoding */
470 for (runlen
= 0; runlen
< 100; runlen
++)
472 if (src
[0] != src
[runlen
])
477 /* Got a useful amount */
482 checksum
+= (encode
= runlen
+ ' ' - 4);
483 putDebugChar (encode
);
499 putDebugChar (highhex(checksum
));
500 putDebugChar (lowhex(checksum
));
502 while (getDebugChar() != '+');
506 /* a bus error has occurred, perform a longjmp
507 to return execution and allow handling of the error */
510 handle_buserror (void)
512 longjmp (remcomEnv
, 1);
516 * this function takes the SH-1 exception number and attempts to
517 * translate this number into a unix compatible signal value
520 computeSignal (int exceptionVector
)
523 switch (exceptionVector
)
525 case INVALID_INSN_VEC
:
528 case INVALID_SLOT_VEC
:
531 case CPU_BUS_ERROR_VEC
:
534 case DMA_BUS_ERROR_VEC
:
547 sigval
= 7; /* "software generated"*/
559 unsigned short opcode
;
561 instrMem
= (short *) registers
[PC
];
566 if ((opcode
& COND_BR_MASK
) == BT_INSTR
)
568 if (registers
[SR
] & T_BIT_MASK
)
570 displacement
= (opcode
& COND_DISP
) << 1;
571 if (displacement
& 0x80)
572 displacement
|= 0xffffff00;
574 * Remember PC points to second instr.
575 * after PC of branch ... so add 4
577 instrMem
= (short *) (registers
[PC
] + displacement
+ 4);
582 else if ((opcode
& COND_BR_MASK
) == BF_INSTR
)
584 if (registers
[SR
] & T_BIT_MASK
)
588 displacement
= (opcode
& COND_DISP
) << 1;
589 if (displacement
& 0x80)
590 displacement
|= 0xffffff00;
592 * Remember PC points to second instr.
593 * after PC of branch ... so add 4
595 instrMem
= (short *) (registers
[PC
] + displacement
+ 4);
598 else if ((opcode
& UCOND_DBR_MASK
) == BRA_INSTR
)
600 displacement
= (opcode
& UCOND_DISP
) << 1;
601 if (displacement
& 0x0800)
602 displacement
|= 0xfffff000;
605 * Remember PC points to second instr.
606 * after PC of branch ... so add 4
608 instrMem
= (short *) (registers
[PC
] + displacement
+ 4);
610 else if ((opcode
& UCOND_RBR_MASK
) == JSR_INSTR
)
612 reg
= (char) ((opcode
& UCOND_REG
) >> 8);
614 instrMem
= (short *) registers
[reg
];
616 else if (opcode
== RTS_INSTR
)
617 instrMem
= (short *) registers
[PR
];
618 else if (opcode
== RTE_INSTR
)
619 instrMem
= (short *) registers
[15];
620 else if ((opcode
& TRAPA_MASK
) == TRAPA_INSTR
)
621 instrMem
= (short *) ((opcode
& ~TRAPA_MASK
) << 2);
625 instrBuffer
.memAddr
= instrMem
;
626 instrBuffer
.oldInstr
= *instrMem
;
627 *instrMem
= SSTEP_INSTR
;
631 /* Undo the effect of a previous doSStep. If we single stepped,
632 restore the old instruction. */
639 instrMem
= instrBuffer
.memAddr
;
640 *instrMem
= instrBuffer
.oldInstr
;
646 This function does all exception handling. It only does two things -
647 it figures out why it was called and tells gdb, and then it reacts
650 When in the monitor mode we talk a human on the serial line rather than gdb.
656 gdb_handle_exception (int exceptionVector
)
658 int sigval
, stepping
;
662 /* reply to host that an exception has occurred */
663 sigval
= computeSignal (exceptionVector
);
664 remcomOutBuffer
[0] = 'S';
665 remcomOutBuffer
[1] = highhex(sigval
);
666 remcomOutBuffer
[2] = lowhex (sigval
);
667 remcomOutBuffer
[3] = 0;
669 putpacket (remcomOutBuffer
);
672 * exception 255 indicates a software trap
673 * inserted in place of code ... so back up
674 * PC by one instruction, since this instruction
675 * will later be replaced by its original one!
677 if (exceptionVector
== 0xff
678 || exceptionVector
== 0x20)
682 * Do the thangs needed to undo
683 * any stepping we may have done!
691 remcomOutBuffer
[0] = 0;
697 remcomOutBuffer
[0] = 'S';
698 remcomOutBuffer
[1] = highhex (sigval
);
699 remcomOutBuffer
[2] = lowhex (sigval
);
700 remcomOutBuffer
[3] = 0;
703 remote_debug
= !(remote_debug
); /* toggle debug flag */
705 case 'g': /* return the value of the CPU registers */
706 mem2hex ((char *) registers
, remcomOutBuffer
, NUMREGBYTES
);
708 case 'G': /* set the value of the CPU registers - return OK */
709 hex2mem (ptr
, (char *) registers
, NUMREGBYTES
);
710 strcpy (remcomOutBuffer
, "OK");
713 /* mAA..AA,LLLL Read LLLL bytes at address AA..AA */
715 if (setjmp (remcomEnv
) == 0)
718 /* TRY, TO READ %x,%x. IF SUCCEED, SET PTR = 0 */
719 if (hexToInt (&ptr
, &addr
))
721 if (hexToInt (&ptr
, &length
))
724 mem2hex ((char *) addr
, remcomOutBuffer
, length
);
727 strcpy (remcomOutBuffer
, "E01");
730 strcpy (remcomOutBuffer
, "E03");
732 /* restore handler for bus error */
736 /* MAA..AA,LLLL: Write LLLL bytes at address AA.AA return OK */
738 if (setjmp (remcomEnv
) == 0)
742 /* TRY, TO READ '%x,%x:'. IF SUCCEED, SET PTR = 0 */
743 if (hexToInt (&ptr
, &addr
))
745 if (hexToInt (&ptr
, &length
))
748 hex2mem (ptr
, (char *) addr
, length
);
750 strcpy (remcomOutBuffer
, "OK");
753 strcpy (remcomOutBuffer
, "E02");
756 strcpy (remcomOutBuffer
, "E03");
758 /* restore handler for bus error */
762 /* cAA..AA Continue at address AA..AA(optional) */
763 /* sAA..AA Step one instruction from AA..AA(optional) */
768 /* tRY, to read optional parameter, pc unchanged if no parm */
769 if (hexToInt (&ptr
, &addr
))
770 registers
[PC
] = addr
;
778 /* kill the program */
779 case 'k': /* do nothing */
783 /* reply to the request */
784 putpacket (remcomOutBuffer
);
789 #define GDBCOOKIE 0x5ac
790 static int ingdbmode
;
791 /* We've had an exception - choose to go into the monitor or
793 void handle_exception(int exceptionVector
)
796 if (ingdbmode
!= GDBCOOKIE
)
797 monitor_handle_exception (exceptionVector
);
800 gdb_handle_exception (exceptionVector
);
807 ingdbmode
= GDBCOOKIE
;
810 /* This function will generate a breakpoint exception. It is used at the
811 beginning of a program to sync up with a debugger and can be used
812 otherwise as a quick means to stop program execution and "break" into
821 /**** Processor-specific routines start here ****/
822 /**** Processor-specific routines start here ****/
823 /**** Processor-specific routines start here ****/
827 The Renesas SH family uses two exception architectures:
831 These processors utilize an exception vector table.
832 Exceptions are vectored to the address stored at VBR + (exception_num * 4)
836 These processors have fixed entry points relative to the VBR for
837 various exception classes.
840 #if defined(__sh1__) || defined(__sh2__)
842 /* SH1/SH2 exception vector table format */
846 void (*func_cold
) ();
848 void (*func_warm
) ();
850 void (*(handler
[256 - 4])) ();
854 /* vectable is the SH1/SH2 vector table. It must be at address 0
855 or wherever your vbr points. */
857 const vec_type vectable
=
859 &BINIT
, /* 0: Power-on reset PC */
860 init_stack
+ init_stack_size
, /* 1: Power-on reset SP */
861 &BINIT
, /* 2: Manual reset PC */
862 init_stack
+ init_stack_size
, /* 3: Manual reset SP */
864 &catch_exception_4
, /* 4: General invalid instruction */
865 &catch_exception_random
, /* 5: Reserved for system */
866 &catch_exception_6
, /* 6: Invalid slot instruction */
867 &catch_exception_random
, /* 7: Reserved for system */
868 &catch_exception_random
, /* 8: Reserved for system */
869 &catch_exception_9
, /* 9: CPU bus error */
870 &catch_exception_10
, /* 10: DMA bus error */
871 &catch_exception_11
, /* 11: NMI */
872 &catch_exception_random
, /* 12: User break */
873 &catch_exception_random
, /* 13: Reserved for system */
874 &catch_exception_random
, /* 14: Reserved for system */
875 &catch_exception_random
, /* 15: Reserved for system */
876 &catch_exception_random
, /* 16: Reserved for system */
877 &catch_exception_random
, /* 17: Reserved for system */
878 &catch_exception_random
, /* 18: Reserved for system */
879 &catch_exception_random
, /* 19: Reserved for system */
880 &catch_exception_random
, /* 20: Reserved for system */
881 &catch_exception_random
, /* 21: Reserved for system */
882 &catch_exception_random
, /* 22: Reserved for system */
883 &catch_exception_random
, /* 23: Reserved for system */
884 &catch_exception_random
, /* 24: Reserved for system */
885 &catch_exception_random
, /* 25: Reserved for system */
886 &catch_exception_random
, /* 26: Reserved for system */
887 &catch_exception_random
, /* 27: Reserved for system */
888 &catch_exception_random
, /* 28: Reserved for system */
889 &catch_exception_random
, /* 29: Reserved for system */
890 &catch_exception_random
, /* 30: Reserved for system */
891 &catch_exception_random
, /* 31: Reserved for system */
892 &catch_exception_32
, /* 32: Trap instr (user vectors) */
893 &catch_exception_33
, /* 33: Trap instr (user vectors) */
894 &catch_exception_random
, /* 34: Trap instr (user vectors) */
895 &catch_exception_random
, /* 35: Trap instr (user vectors) */
896 &catch_exception_random
, /* 36: Trap instr (user vectors) */
897 &catch_exception_random
, /* 37: Trap instr (user vectors) */
898 &catch_exception_random
, /* 38: Trap instr (user vectors) */
899 &catch_exception_random
, /* 39: Trap instr (user vectors) */
900 &catch_exception_random
, /* 40: Trap instr (user vectors) */
901 &catch_exception_random
, /* 41: Trap instr (user vectors) */
902 &catch_exception_random
, /* 42: Trap instr (user vectors) */
903 &catch_exception_random
, /* 43: Trap instr (user vectors) */
904 &catch_exception_random
, /* 44: Trap instr (user vectors) */
905 &catch_exception_random
, /* 45: Trap instr (user vectors) */
906 &catch_exception_random
, /* 46: Trap instr (user vectors) */
907 &catch_exception_random
, /* 47: Trap instr (user vectors) */
908 &catch_exception_random
, /* 48: Trap instr (user vectors) */
909 &catch_exception_random
, /* 49: Trap instr (user vectors) */
910 &catch_exception_random
, /* 50: Trap instr (user vectors) */
911 &catch_exception_random
, /* 51: Trap instr (user vectors) */
912 &catch_exception_random
, /* 52: Trap instr (user vectors) */
913 &catch_exception_random
, /* 53: Trap instr (user vectors) */
914 &catch_exception_random
, /* 54: Trap instr (user vectors) */
915 &catch_exception_random
, /* 55: Trap instr (user vectors) */
916 &catch_exception_random
, /* 56: Trap instr (user vectors) */
917 &catch_exception_random
, /* 57: Trap instr (user vectors) */
918 &catch_exception_random
, /* 58: Trap instr (user vectors) */
919 &catch_exception_random
, /* 59: Trap instr (user vectors) */
920 &catch_exception_random
, /* 60: Trap instr (user vectors) */
921 &catch_exception_random
, /* 61: Trap instr (user vectors) */
922 &catch_exception_random
, /* 62: Trap instr (user vectors) */
923 &catch_exception_random
, /* 63: Trap instr (user vectors) */
924 &catch_exception_random
, /* 64: IRQ0 */
925 &catch_exception_random
, /* 65: IRQ1 */
926 &catch_exception_random
, /* 66: IRQ2 */
927 &catch_exception_random
, /* 67: IRQ3 */
928 &catch_exception_random
, /* 68: IRQ4 */
929 &catch_exception_random
, /* 69: IRQ5 */
930 &catch_exception_random
, /* 70: IRQ6 */
931 &catch_exception_random
, /* 71: IRQ7 */
932 &catch_exception_random
,
933 &catch_exception_random
,
934 &catch_exception_random
,
935 &catch_exception_random
,
936 &catch_exception_random
,
937 &catch_exception_random
,
938 &catch_exception_random
,
939 &catch_exception_random
,
940 &catch_exception_random
,
941 &catch_exception_random
,
942 &catch_exception_random
,
943 &catch_exception_random
,
944 &catch_exception_random
,
945 &catch_exception_random
,
946 &catch_exception_random
,
947 &catch_exception_random
,
948 &catch_exception_random
,
949 &catch_exception_random
,
950 &catch_exception_random
,
951 &catch_exception_random
,
952 &catch_exception_random
,
953 &catch_exception_random
,
954 &catch_exception_random
,
955 &catch_exception_random
,
956 &catch_exception_random
,
957 &catch_exception_random
,
958 &catch_exception_random
,
959 &catch_exception_random
,
960 &catch_exception_random
,
961 &catch_exception_random
,
962 &catch_exception_random
,
963 &catch_exception_random
,
964 &catch_exception_random
,
965 &catch_exception_random
,
966 &catch_exception_random
,
967 &catch_exception_random
,
968 &catch_exception_random
,
969 &catch_exception_random
,
970 &catch_exception_random
,
971 &catch_exception_random
,
972 &catch_exception_random
,
973 &catch_exception_random
,
974 &catch_exception_random
,
975 &catch_exception_random
,
976 &catch_exception_random
,
977 &catch_exception_random
,
978 &catch_exception_random
,
979 &catch_exception_random
,
980 &catch_exception_random
,
981 &catch_exception_random
,
982 &catch_exception_random
,
983 &catch_exception_random
,
984 &catch_exception_random
,
985 &catch_exception_random
,
986 &catch_exception_random
,
987 &catch_exception_random
,
988 &catch_exception_random
,
989 &catch_exception_random
,
990 &catch_exception_random
,
991 &catch_exception_random
,
992 &catch_exception_random
,
993 &catch_exception_random
,
994 &catch_exception_random
,
995 &catch_exception_random
,
996 &catch_exception_random
,
997 &catch_exception_random
,
998 &catch_exception_random
,
999 &catch_exception_random
,
1000 &catch_exception_random
,
1001 &catch_exception_random
,
1002 &catch_exception_random
,
1003 &catch_exception_random
,
1004 &catch_exception_random
,
1005 &catch_exception_random
,
1006 &catch_exception_random
,
1007 &catch_exception_random
,
1008 &catch_exception_random
,
1009 &catch_exception_random
,
1010 &catch_exception_random
,
1011 &catch_exception_random
,
1012 &catch_exception_random
,
1013 &catch_exception_random
,
1014 &catch_exception_random
,
1015 &catch_exception_random
,
1016 &catch_exception_random
,
1017 &catch_exception_random
,
1018 &catch_exception_random
,
1019 &catch_exception_random
,
1020 &catch_exception_random
,
1021 &catch_exception_random
,
1022 &catch_exception_random
,
1023 &catch_exception_random
,
1024 &catch_exception_random
,
1025 &catch_exception_random
,
1026 &catch_exception_random
,
1027 &catch_exception_random
,
1028 &catch_exception_random
,
1029 &catch_exception_random
,
1030 &catch_exception_random
,
1031 &catch_exception_random
,
1032 &catch_exception_random
,
1033 &catch_exception_random
,
1034 &catch_exception_random
,
1035 &catch_exception_random
,
1036 &catch_exception_random
,
1037 &catch_exception_random
,
1038 &catch_exception_random
,
1039 &catch_exception_random
,
1040 &catch_exception_random
,
1041 &catch_exception_random
,
1042 &catch_exception_random
,
1043 &catch_exception_random
,
1044 &catch_exception_random
,
1045 &catch_exception_random
,
1046 &catch_exception_random
,
1047 &catch_exception_random
,
1048 &catch_exception_random
,
1049 &catch_exception_random
,
1050 &catch_exception_random
,
1051 &catch_exception_random
,
1052 &catch_exception_random
,
1053 &catch_exception_random
,
1054 &catch_exception_random
,
1055 &catch_exception_random
,
1056 &catch_exception_random
,
1057 &catch_exception_random
,
1058 &catch_exception_random
,
1059 &catch_exception_random
,
1060 &catch_exception_random
,
1061 &catch_exception_random
,
1062 &catch_exception_random
,
1063 &catch_exception_random
,
1064 &catch_exception_random
,
1065 &catch_exception_random
,
1066 &catch_exception_random
,
1067 &catch_exception_random
,
1068 &catch_exception_random
,
1069 &catch_exception_random
,
1070 &catch_exception_random
,
1071 &catch_exception_random
,
1072 &catch_exception_random
,
1073 &catch_exception_random
,
1074 &catch_exception_random
,
1075 &catch_exception_random
,
1076 &catch_exception_random
,
1077 &catch_exception_random
,
1078 &catch_exception_random
,
1079 &catch_exception_random
,
1080 &catch_exception_random
,
1081 &catch_exception_random
,
1082 &catch_exception_random
,
1083 &catch_exception_random
,
1084 &catch_exception_random
,
1085 &catch_exception_random
,
1086 &catch_exception_random
,
1087 &catch_exception_random
,
1088 &catch_exception_random
,
1089 &catch_exception_random
,
1090 &catch_exception_random
,
1091 &catch_exception_random
,
1092 &catch_exception_random
,
1093 &catch_exception_random
,
1094 &catch_exception_random
,
1095 &catch_exception_random
,
1096 &catch_exception_random
,
1097 &catch_exception_random
,
1098 &catch_exception_random
,
1099 &catch_exception_random
,
1100 &catch_exception_random
,
1101 &catch_exception_random
,
1102 &catch_exception_random
,
1103 &catch_exception_random
,
1104 &catch_exception_random
,
1105 &catch_exception_random
,
1106 &catch_exception_random
,
1107 &catch_exception_random
,
1108 &catch_exception_random
,
1109 &catch_exception_random
,
1110 &catch_exception_random
,
1111 &catch_exception_random
,
1112 &catch_exception_random
,
1113 &catch_exception_random
,
1114 &catch_exception_random
,
1115 &catch_exception_255
}};
1117 #define BCR (*(volatile short *)(0x05FFFFA0)) /* Bus control register */
1118 #define BAS (0x800) /* Byte access select */
1119 #define WCR1 (*(volatile short *)(0x05ffffA2)) /* Wait state control register */
1121 asm ("_BINIT: mov.l L1,r15");
1124 asm ("L1: .long _init_stack + 8*1024*4");
1128 /* First turn on the ram */
1129 WCR1
= 0; /* Never sample wait */
1130 BCR
= BAS
; /* use lowbyte/high byte */
1143 stub_sp
= stub_stack
+ stub_stack_size
;
1155 /* Calling Reset does the same as pressing the button */
1156 asm (".global _Reset
1164 L_sp: .long _init_stack + 8000");
1167 mov.l @(L_reg, pc), r0
1168 mov.l @r15+, r1 ! pop R0
1169 mov.l r2, @(0x08, r0) ! save R2
1170 mov.l r1, @r0 ! save R0
1171 mov.l @r15+, r1 ! pop R1
1172 mov.l r3, @(0x0c, r0) ! save R3
1173 mov.l r1, @(0x04, r0) ! save R1
1174 mov.l r4, @(0x10, r0) ! save R4
1175 mov.l r5, @(0x14, r0) ! save R5
1176 mov.l r6, @(0x18, r0) ! save R6
1177 mov.l r7, @(0x1c, r0) ! save R7
1178 mov.l r8, @(0x20, r0) ! save R8
1179 mov.l r9, @(0x24, r0) ! save R9
1180 mov.l r10, @(0x28, r0) ! save R10
1181 mov.l r11, @(0x2c, r0) ! save R11
1182 mov.l r12, @(0x30, r0) ! save R12
1183 mov.l r13, @(0x34, r0) ! save R13
1184 mov.l r14, @(0x38, r0) ! save R14
1185 mov.l @r15+, r4 ! save arg to handleException
1186 add #8, r15 ! hide PC/SR values on stack
1187 mov.l r15, @(0x3c, r0) ! save R15
1188 add #-8, r15 ! save still needs old SP value
1189 add #92, r0 ! readjust register pointer
1192 mov.l @r2, r2 ! R2 has SR
1193 mov.l @r15, r1 ! R1 has PC
1194 mov.l r2, @-r0 ! save SR
1195 sts.l macl, @-r0 ! save MACL
1196 sts.l mach, @-r0 ! save MACH
1197 stc.l vbr, @-r0 ! save VBR
1198 stc.l gbr, @-r0 ! save GBR
1199 sts.l pr, @-r0 ! save PR
1200 mov.l @(L_stubstack, pc), r2
1201 mov.l @(L_hdl_except, pc), r3
1204 mov.l r1, @-r0 ! save PC
1205 mov.l @(L_stubstack, pc), r0
1206 mov.l @(L_reg, pc), r1
1207 bra restoreRegisters
1208 mov.l r15, @r0 ! save __stub_stack
1216 .long _handle_exception");
1228 add #8, r1 ! skip to R2
1229 mov.l @r1+, r2 ! restore R2
1230 mov.l @r1+, r3 ! restore R3
1231 mov.l @r1+, r4 ! restore R4
1232 mov.l @r1+, r5 ! restore R5
1233 mov.l @r1+, r6 ! restore R6
1234 mov.l @r1+, r7 ! restore R7
1235 mov.l @r1+, r8 ! restore R8
1236 mov.l @r1+, r9 ! restore R9
1237 mov.l @r1+, r10 ! restore R10
1238 mov.l @r1+, r11 ! restore R11
1239 mov.l @r1+, r12 ! restore R12
1240 mov.l @r1+, r13 ! restore R13
1241 mov.l @r1+, r14 ! restore R14
1242 mov.l @r1+, r15 ! restore programs stack
1244 add #-8, r15 ! uncover PC/SR on stack
1245 mov.l r0, @r15 ! restore PC onto stack
1246 lds.l @r1+, pr ! restore PR
1247 ldc.l @r1+, gbr ! restore GBR
1248 ldc.l @r1+, vbr ! restore VBR
1249 lds.l @r1+, mach ! restore MACH
1250 lds.l @r1+, macl ! restore MACL
1252 add #-88, r1 ! readjust reg pointer to R1
1253 mov.l r0, @(4, r15) ! restore SR onto stack+4
1259 mov.l @r1+, r0 ! restore R0
1261 mov.l @r1, r1 ! restore R1
1267 static __inline__
void code_for_catch_exception(int n
)
1269 asm(" .globl _catch_exception_%O0" : : "i" (n
) );
1270 asm(" _catch_exception_%O0:" :: "i" (n
) );
1272 asm(" add #-4, r15 ! reserve spot on stack ");
1273 asm(" mov.l r1, @-r15 ! push R1 ");
1277 /* Special case for NMI - make sure that they don't nest */
1278 asm(" mov.l r0, @-r15 ! push R0");
1279 asm(" mov.l L_in_nmi, r0");
1280 asm(" tas.b @r0 ! Fend off against addtnl NMIs");
1282 asm(" mov.l @r15+, r0");
1283 asm(" mov.l @r15+, r1");
1284 asm(" add #4, r15");
1288 asm("L_in_nmi: .long _in_nmi");
1294 if (n
== CPU_BUS_ERROR_VEC
)
1296 /* Exception 9 (bus errors) are disasbleable - so that you
1297 can probe memory and get zero instead of a fault.
1298 Because the vector table may be in ROM we don't revector
1299 the interrupt like all the other stubs, we check in here
1301 asm("mov.l L_dofault,r1");
1302 asm("mov.l @r1,r1");
1304 asm("bf faultaway");
1305 asm("bsr _handle_buserror");
1307 asm("L_dofault: .long _dofault");
1310 asm(" mov #15<<4, r1 ");
1311 asm(" ldc r1, sr ! disable interrupts ");
1312 asm(" mov.l r0, @-r15 ! push R0 ");
1315 /* Prepare for saving context, we've already pushed r0 and r1, stick exception number
1317 asm(" mov r15, r0 ");
1318 asm(" add #8, r0 ");
1319 asm(" mov %0,r1" :: "i" (n
) );
1320 asm(" extu.b r1,r1 ");
1321 asm(" bra saveRegisters ! save register values ");
1322 asm(" mov.l r1, @r0 ! save exception # ");
1329 code_for_catch_exception (CPU_BUS_ERROR_VEC
);
1330 code_for_catch_exception (DMA_BUS_ERROR_VEC
);
1331 code_for_catch_exception (INVALID_INSN_VEC
);
1332 code_for_catch_exception (INVALID_SLOT_VEC
);
1333 code_for_catch_exception (NMI_VEC
);
1334 code_for_catch_exception (TRAP_VEC
);
1335 code_for_catch_exception (USER_VEC
);
1336 code_for_catch_exception (IO_VEC
);
1344 /* Support for Serial I/O using on chip uart */
1346 #define SMR0 (*(volatile char *)(0x05FFFEC0)) /* Channel 0 serial mode register */
1347 #define BRR0 (*(volatile char *)(0x05FFFEC1)) /* Channel 0 bit rate register */
1348 #define SCR0 (*(volatile char *)(0x05FFFEC2)) /* Channel 0 serial control register */
1349 #define TDR0 (*(volatile char *)(0x05FFFEC3)) /* Channel 0 transmit data register */
1350 #define SSR0 (*(volatile char *)(0x05FFFEC4)) /* Channel 0 serial status register */
1351 #define RDR0 (*(volatile char *)(0x05FFFEC5)) /* Channel 0 receive data register */
1353 #define SMR1 (*(volatile char *)(0x05FFFEC8)) /* Channel 1 serial mode register */
1354 #define BRR1 (*(volatile char *)(0x05FFFEC9)) /* Channel 1 bit rate register */
1355 #define SCR1 (*(volatile char *)(0x05FFFECA)) /* Channel 1 serial control register */
1356 #define TDR1 (*(volatile char *)(0x05FFFECB)) /* Channel 1 transmit data register */
1357 #define SSR1 (*(volatile char *)(0x05FFFECC)) /* Channel 1 serial status register */
1358 #define RDR1 (*(volatile char *)(0x05FFFECD)) /* Channel 1 receive data register */
1361 * Serial mode register bits
1364 #define SYNC_MODE 0x80
1365 #define SEVEN_BIT_DATA 0x40
1366 #define PARITY_ON 0x20
1367 #define ODD_PARITY 0x10
1368 #define STOP_BITS_2 0x08
1369 #define ENABLE_MULTIP 0x04
1375 * Serial control register bits
1377 #define SCI_TIE 0x80 /* Transmit interrupt enable */
1378 #define SCI_RIE 0x40 /* Receive interrupt enable */
1379 #define SCI_TE 0x20 /* Transmit enable */
1380 #define SCI_RE 0x10 /* Receive enable */
1381 #define SCI_MPIE 0x08 /* Multiprocessor interrupt enable */
1382 #define SCI_TEIE 0x04 /* Transmit end interrupt enable */
1383 #define SCI_CKE1 0x02 /* Clock enable 1 */
1384 #define SCI_CKE0 0x01 /* Clock enable 0 */
1387 * Serial status register bits
1389 #define SCI_TDRE 0x80 /* Transmit data register empty */
1390 #define SCI_RDRF 0x40 /* Receive data register full */
1391 #define SCI_ORER 0x20 /* Overrun error */
1392 #define SCI_FER 0x10 /* Framing error */
1393 #define SCI_PER 0x08 /* Parity error */
1394 #define SCI_TEND 0x04 /* Transmit end */
1395 #define SCI_MPB 0x02 /* Multiprocessor bit */
1396 #define SCI_MPBT 0x01 /* Multiprocessor bit transfer */
1400 * Port B IO Register (PBIOR)
1402 #define PBIOR (*(volatile char *)(0x05FFFFC6))
1403 #define PB15IOR 0x8000
1404 #define PB14IOR 0x4000
1405 #define PB13IOR 0x2000
1406 #define PB12IOR 0x1000
1407 #define PB11IOR 0x0800
1408 #define PB10IOR 0x0400
1409 #define PB9IOR 0x0200
1410 #define PB8IOR 0x0100
1411 #define PB7IOR 0x0080
1412 #define PB6IOR 0x0040
1413 #define PB5IOR 0x0020
1414 #define PB4IOR 0x0010
1415 #define PB3IOR 0x0008
1416 #define PB2IOR 0x0004
1417 #define PB1IOR 0x0002
1418 #define PB0IOR 0x0001
1421 * Port B Control Register (PBCR1)
1423 #define PBCR1 (*(volatile short *)(0x05FFFFCC))
1424 #define PB15MD1 0x8000
1425 #define PB15MD0 0x4000
1426 #define PB14MD1 0x2000
1427 #define PB14MD0 0x1000
1428 #define PB13MD1 0x0800
1429 #define PB13MD0 0x0400
1430 #define PB12MD1 0x0200
1431 #define PB12MD0 0x0100
1432 #define PB11MD1 0x0080
1433 #define PB11MD0 0x0040
1434 #define PB10MD1 0x0020
1435 #define PB10MD0 0x0010
1436 #define PB9MD1 0x0008
1437 #define PB9MD0 0x0004
1438 #define PB8MD1 0x0002
1439 #define PB8MD0 0x0001
1441 #define PB15MD PB15MD1|PB14MD0
1442 #define PB14MD PB14MD1|PB14MD0
1443 #define PB13MD PB13MD1|PB13MD0
1444 #define PB12MD PB12MD1|PB12MD0
1445 #define PB11MD PB11MD1|PB11MD0
1446 #define PB10MD PB10MD1|PB10MD0
1447 #define PB9MD PB9MD1|PB9MD0
1448 #define PB8MD PB8MD1|PB8MD0
1450 #define PB_TXD1 PB11MD1
1451 #define PB_RXD1 PB10MD1
1452 #define PB_TXD0 PB9MD1
1453 #define PB_RXD0 PB8MD1
1456 * Port B Control Register (PBCR2)
1458 #define PBCR2 0x05FFFFCE
1459 #define PB7MD1 0x8000
1460 #define PB7MD0 0x4000
1461 #define PB6MD1 0x2000
1462 #define PB6MD0 0x1000
1463 #define PB5MD1 0x0800
1464 #define PB5MD0 0x0400
1465 #define PB4MD1 0x0200
1466 #define PB4MD0 0x0100
1467 #define PB3MD1 0x0080
1468 #define PB3MD0 0x0040
1469 #define PB2MD1 0x0020
1470 #define PB2MD0 0x0010
1471 #define PB1MD1 0x0008
1472 #define PB1MD0 0x0004
1473 #define PB0MD1 0x0002
1474 #define PB0MD0 0x0001
1476 #define PB7MD PB7MD1|PB7MD0
1477 #define PB6MD PB6MD1|PB6MD0
1478 #define PB5MD PB5MD1|PB5MD0
1479 #define PB4MD PB4MD1|PB4MD0
1480 #define PB3MD PB3MD1|PB3MD0
1481 #define PB2MD PB2MD1|PB2MD0
1482 #define PB1MD PB1MD1|PB1MD0
1483 #define PB0MD PB0MD1|PB0MD0
1487 #define BPS 32 * 9600 * MHZ / ( BAUD * 10)
1489 #define BPS 32 /* 9600 for 10 Mhz */
1492 void handleError (char theSSR
);
1504 /* Clear TE and RE in Channel 1's SCR */
1505 SCR1
&= ~(SCI_TE
| SCI_RE
);
1507 /* Set communication to be async, 8-bit data, no parity, 1 stop bit and use internal clock */
1512 SCR1
&= ~(SCI_CKE1
| SCI_CKE0
);
1514 /* let the hardware settle */
1516 for (i
= 0; i
< 1000; i
++)
1519 /* Turn on in and out */
1520 SCR1
|= SCI_RE
| SCI_TE
;
1522 /* Set the PFC to make RXD1 (pin PB8) an input pin and TXD1 (pin PB9) an output pin */
1523 PBCR1
&= ~(PB_TXD1
| PB_RXD1
);
1524 PBCR1
|= PB_TXD1
| PB_RXD1
;
1529 getDebugCharReady (void)
1532 mySSR
= SSR1
& ( SCI_PER
| SCI_FER
| SCI_ORER
);
1534 handleError ( mySSR
);
1535 return SSR1
& SCI_RDRF
;
1544 while ( ! getDebugCharReady())
1550 mySSR
= SSR1
& (SCI_PER
| SCI_FER
| SCI_ORER
);
1553 handleError (mySSR
);
1559 putDebugCharReady (void)
1561 return (SSR1
& SCI_TDRE
);
1565 putDebugChar (char ch
)
1567 while (!putDebugCharReady())
1571 * Write data into TDR and clear TDRE
1578 handleError (char theSSR
)
1580 SSR1
&= ~(SCI_ORER
| SCI_PER
| SCI_FER
);
This page took 0.060442 seconds and 4 git commands to generate.