include/asm-powerpc/smu.h

   1 #ifndef _SMU_H
   2 #define _SMU_H
   3
   4 /*
   5  * Definitions for talking to the SMU chip in newer G5 PowerMacs
   6  */
   7
   8 #include <linux/config.h>
   9 #include <linux/list.h>
  10
  11 /*
  12  * Known SMU commands
  13  *
  14  * Most of what is below comes from looking at the Open Firmware driver,
  15  * though this is still incomplete and could use better documentation here
  16  * or there...
  17  */
  18
  19
  20 /*
  21  * Partition info commands
  22  *
  23  * I do not know what those are for at this point
  24  */
  25 #define SMU_CMD_PARTITION_COMMAND               0x3e
  26
  27
  28 /*
  29  * Fan control
  30  *
  31  * This is a "mux" for fan control commands, first byte is the
  32  * "sub" command.
  33  */
  34 #define SMU_CMD_FAN_COMMAND                     0x4a
  35
  36
  37 /*
  38  * Battery access
  39  *
  40  * Same command number as the PMU, could it be same syntax ?
  41  */
  42 #define SMU_CMD_BATTERY_COMMAND                 0x6f
  43 #define   SMU_CMD_GET_BATTERY_INFO              0x00
  44
  45 /*
  46  * Real time clock control
  47  *
  48  * This is a "mux", first data byte contains the "sub" command.
  49  * The "RTC" part of the SMU controls the date, time, powerup
  50  * timer, but also a PRAM
  51  *
  52  * Dates are in BCD format on 7 bytes:
  53  * [sec] [min] [hour] [weekday] [month day] [month] [year]
  54  * with month being 1 based and year minus 100
  55  */
  56 #define SMU_CMD_RTC_COMMAND                     0x8e
  57 #define   SMU_CMD_RTC_SET_PWRUP_TIMER           0x00 /* i: 7 bytes date */
  58 #define   SMU_CMD_RTC_GET_PWRUP_TIMER           0x01 /* o: 7 bytes date */
  59 #define   SMU_CMD_RTC_STOP_PWRUP_TIMER          0x02
  60 #define   SMU_CMD_RTC_SET_PRAM_BYTE_ACC         0x20 /* i: 1 byte (address?) */
  61 #define   SMU_CMD_RTC_SET_PRAM_AUTOINC          0x21 /* i: 1 byte (data?) */
  62 #define   SMU_CMD_RTC_SET_PRAM_LO_BYTES         0x22 /* i: 10 bytes */
  63 #define   SMU_CMD_RTC_SET_PRAM_HI_BYTES         0x23 /* i: 10 bytes */
  64 #define   SMU_CMD_RTC_GET_PRAM_BYTE             0x28 /* i: 1 bytes (address?) */
  65 #define   SMU_CMD_RTC_GET_PRAM_LO_BYTES         0x29 /* o: 10 bytes */
  66 #define   SMU_CMD_RTC_GET_PRAM_HI_BYTES         0x2a /* o: 10 bytes */
  67 #define   SMU_CMD_RTC_SET_DATETIME              0x80 /* i: 7 bytes date */
  68 #define   SMU_CMD_RTC_GET_DATETIME              0x81 /* o: 7 bytes date */
  69
  70  /*
  71   * i2c commands
  72   *
  73   * To issue an i2c command, first is to send a parameter block to the
  74   * the SMU. This is a command of type 0x9a with 9 bytes of header
  75   * eventually followed by data for a write:
  76   *
  77   * 0: bus number (from device-tree usually, SMU has lots of busses !)
  78   * 1: transfer type/format (see below)
  79   * 2: device address. For combined and combined4 type transfers, this
  80   *    is the "write" version of the address (bit 0x01 cleared)
  81   * 3: subaddress length (0..3)
  82   * 4: subaddress byte 0 (or only byte for subaddress length 1)
  83   * 5: subaddress byte 1
  84   * 6: subaddress byte 2
  85   * 7: combined address (device address for combined mode data phase)
  86   * 8: data length
  87   *
  88   * The transfer types are the same good old Apple ones it seems,
  89   * that is:
  90   *   - 0x00: Simple transfer
  91   *   - 0x01: Subaddress transfer (addr write + data tx, no restart)
  92   *   - 0x02: Combined transfer (addr write + restart + data tx)
  93   *
  94   * This is then followed by actual data for a write.
  95   *
  96   * At this point, the OF driver seems to have a limitation on transfer
  97   * sizes of 0xd bytes on reads and 0x5 bytes on writes. I do not know
  98   * wether this is just an OF limit due to some temporary buffer size
  99   * or if this is an SMU imposed limit. This driver has the same limitation
 100   * for now as I use a 0x10 bytes temporary buffer as well
 101   *
 102   * Once that is completed, a response is expected from the SMU. This is
 103   * obtained via a command of type 0x9a with a length of 1 byte containing
 104   * 0 as the data byte. OF also fills the rest of the data buffer with 0xff's
 105   * though I can't tell yet if this is actually necessary. Once this command
 106   * is complete, at this point, all I can tell is what OF does. OF tests
 107   * byte 0 of the reply:
 108   *   - on read, 0xfe or 0xfc : bus is busy, wait (see below) or nak ?
 109   *   - on read, 0x00 or 0x01 : reply is in buffer (after the byte 0)
 110   *   - on write, < 0 -> failure (immediate exit)
 111   *   - else, OF just exists (without error, weird)
 112   *
 113   * So on read, there is this wait-for-busy thing when getting a 0xfc or
 114   * 0xfe result. OF does a loop of up to 64 retries, waiting 20ms and
 115   * doing the above again until either the retries expire or the result
 116   * is no longer 0xfe or 0xfc
 117   *
 118   * The Darwin I2C driver is less subtle though. On any non-success status
 119   * from the response command, it waits 5ms and tries again up to 20 times,
 120   * it doesn't differenciate between fatal errors or "busy" status.
 121   *
 122   * This driver provides an asynchronous paramblock based i2c command
 123   * interface to be used either directly by low level code or by a higher
 124   * level driver interfacing to the linux i2c layer. The current
 125   * implementation of this relies on working timers & timer interrupts
 126   * though, so be careful of calling context for now. This may be "fixed"
 127   * in the future by adding a polling facility.
 128   */
 129 #define SMU_CMD_I2C_COMMAND                     0x9a
 130           /* transfer types */
 131 #define   SMU_I2C_TRANSFER_SIMPLE       0x00
 132 #define   SMU_I2C_TRANSFER_STDSUB       0x01
 133 #define   SMU_I2C_TRANSFER_COMBINED     0x02
 134
 135 /*
 136  * Power supply control
 137  *
 138  * The "sub" command is an ASCII string in the data, the
 139  * data lenght is that of the string.
 140  *
 141  * The VSLEW command can be used to get or set the voltage slewing.
 142  *  - lenght 5 (only "VSLEW") : it returns "DONE" and 3 bytes of
 143  *    reply at data offset 6, 7 and 8.
 144  *  - lenght 8 ("VSLEWxyz") has 3 additional bytes appended, and is
 145  *    used to set the voltage slewing point. The SMU replies with "DONE"
 146  * I yet have to figure out their exact meaning of those 3 bytes in
 147  * both cases.
 148  *
 149  */
 150 #define SMU_CMD_POWER_COMMAND                   0xaa
 151 #define   SMU_CMD_POWER_RESTART                 "RESTART"
 152 #define   SMU_CMD_POWER_SHUTDOWN                "SHUTDOWN"
 153 #define   SMU_CMD_POWER_VOLTAGE_SLEW            "VSLEW"
 154
 155 /* Misc commands
 156  *
 157  * This command seem to be a grab bag of various things
 158  */
 159 #define SMU_CMD_MISC_df_COMMAND                 0xdf
 160 #define   SMU_CMD_MISC_df_SET_DISPLAY_LIT       0x02 /* i: 1 byte */
 161 #define   SMU_CMD_MISC_df_NMI_OPTION            0x04
 162
 163 /*
 164  * Version info commands
 165  *
 166  * I haven't quite tried to figure out how these work
 167  */
 168 #define SMU_CMD_VERSION_COMMAND                 0xea
 169
 170
 171 /*
 172  * Misc commands
 173  *
 174  * This command seem to be a grab bag of various things
 175  */
 176 #define SMU_CMD_MISC_ee_COMMAND                 0xee
 177 #define   SMU_CMD_MISC_ee_GET_DATABLOCK_REC     0x02
 178 #define   SMU_CMD_MISC_ee_LEDS_CTRL             0x04 /* i: 00 (00,01) [00] */
 179 #define   SMU_CMD_MISC_ee_GET_DATA              0x05 /* i: 00 , o: ?? */
 180
 181
 182
 183 /*
 184  * - Kernel side interface -
 185  */
 186
 187 #ifdef __KERNEL__
 188
 189 /*
 190  * Asynchronous SMU commands
 191  *
 192  * Fill up this structure and submit it via smu_queue_command(),
 193  * and get notified by the optional done() callback, or because
 194  * status becomes != 1
 195  */
 196
 197 struct smu_cmd;
 198
 199 struct smu_cmd
 200 {
 201         /* public */
 202         u8                      cmd;            /* command */
 203         int                     data_len;       /* data len */
 204         int                     reply_len;      /* reply len */
 205         void                    *data_buf;      /* data buffer */
 206         void                    *reply_buf;     /* reply buffer */
 207         int                     status;         /* command status */
 208         void                    (*done)(struct smu_cmd *cmd, void *misc);
 209         void                    *misc;
 210
 211         /* private */
 212         struct list_head        link;
 213 };
 214
 215 /*
 216  * Queues an SMU command, all fields have to be initialized
 217  */
 218 extern int smu_queue_cmd(struct smu_cmd *cmd);
 219
 220 /*
 221  * Simple command wrapper. This structure embeds a small buffer
 222  * to ease sending simple SMU commands from the stack
 223  */
 224 struct smu_simple_cmd
 225 {
 226         struct smu_cmd  cmd;
 227         u8              buffer[16];
 228 };
 229
 230 /*
 231  * Queues a simple command. All fields will be initialized by that
 232  * function
 233  */
 234 extern int smu_queue_simple(struct smu_simple_cmd *scmd, u8 command,
 235                             unsigned int data_len,
 236                             void (*done)(struct smu_cmd *cmd, void *misc),
 237                             void *misc,
 238                             ...);
 239
 240 /*
 241  * Completion helper. Pass it to smu_queue_simple or as 'done'
 242  * member to smu_queue_cmd, it will call complete() on the struct
 243  * completion passed in the "misc" argument
 244  */
 245 extern void smu_done_complete(struct smu_cmd *cmd, void *misc);
 246
 247 /*
 248  * Synchronous helpers. Will spin-wait for completion of a command
 249  */
 250 extern void smu_spinwait_cmd(struct smu_cmd *cmd);
 251
 252 static inline void smu_spinwait_simple(struct smu_simple_cmd *scmd)
 253 {
 254         smu_spinwait_cmd(&scmd->cmd);
 255 }
 256
 257 /*
 258  * Poll routine to call if blocked with irqs off
 259  */
 260 extern void smu_poll(void);
 261
 262
 263 /*
 264  * Init routine, presence check....
 265  */
 266 extern int smu_init(void);
 267 extern int smu_present(void);
 268 struct of_device;
 269 extern struct of_device *smu_get_ofdev(void);
 270
 271
 272 /*
 273  * Common command wrappers
 274  */
 275 extern void smu_shutdown(void);
 276 extern void smu_restart(void);
 277 struct rtc_time;
 278 extern int smu_get_rtc_time(struct rtc_time *time, int spinwait);
 279 extern int smu_set_rtc_time(struct rtc_time *time, int spinwait);
 280
 281 /*
 282  * SMU command buffer absolute address, exported by pmac_setup,
 283  * this is allocated very early during boot.
 284  */
 285 extern unsigned long smu_cmdbuf_abs;
 286
 287
 288 /*
 289  * Kenrel asynchronous i2c interface
 290  */
 291
 292 /* SMU i2c header, exactly matches i2c header on wire */
 293 struct smu_i2c_param
 294 {
 295         u8      bus;            /* SMU bus ID (from device tree) */
 296         u8      type;           /* i2c transfer type */
 297         u8      devaddr;        /* device address (includes direction) */
 298         u8      sublen;         /* subaddress length */
 299         u8      subaddr[3];     /* subaddress */
 300         u8      caddr;          /* combined address, filled by SMU driver */
 301         u8      datalen;        /* length of transfer */
 302         u8      data[7];        /* data */
 303 };
 304
 305 #define SMU_I2C_READ_MAX        0x0d
 306 #define SMU_I2C_WRITE_MAX       0x05
 307
 308 struct smu_i2c_cmd
 309 {
 310         /* public */
 311         struct smu_i2c_param    info;
 312         void                    (*done)(struct smu_i2c_cmd *cmd, void *misc);
 313         void                    *misc;
 314         int                     status; /* 1 = pending, 0 = ok, <0 = fail */
 315
 316         /* private */
 317         struct smu_cmd          scmd;
 318         int                     read;
 319         int                     stage;
 320         int                     retries;
 321         u8                      pdata[0x10];
 322         struct list_head        link;
 323 };
 324
 325 /*
 326  * Call this to queue an i2c command to the SMU. You must fill info,
 327  * including info.data for a write, done and misc.
 328  * For now, no polling interface is provided so you have to use completion
 329  * callback.
 330  */
 331 extern int smu_queue_i2c(struct smu_i2c_cmd *cmd);
 332
 333
 334 #endif /* __KERNEL__ */
 335
 336 /*
 337  * - Userland interface -
 338  */
 339
 340 /*
 341  * A given instance of the device can be configured for 2 different
 342  * things at the moment:
 343  *
 344  *  - sending SMU commands (default at open() time)
 345  *  - receiving SMU events (not yet implemented)
 346  *
 347  * Commands are written with write() of a command block. They can be
 348  * "driver" commands (for example to switch to event reception mode)
 349  * or real SMU commands. They are made of a header followed by command
 350  * data if any.
 351  *
 352  * For SMU commands (not for driver commands), you can then read() back
 353  * a reply. The reader will be blocked or not depending on how the device
 354  * file is opened. poll() isn't implemented yet. The reply will consist
 355  * of a header as well, followed by the reply data if any. You should
 356  * always provide a buffer large enough for the maximum reply data, I
 357  * recommand one page.
 358  *
 359  * It is illegal to send SMU commands through a file descriptor configured
 360  * for events reception
 361  *
 362  */
 363 struct smu_user_cmd_hdr
 364 {
 365         __u32           cmdtype;
 366 #define SMU_CMDTYPE_SMU                 0       /* SMU command */
 367 #define SMU_CMDTYPE_WANTS_EVENTS        1       /* switch fd to events mode */
 368
 369         __u8            cmd;                    /* SMU command byte */
 370         __u32           data_len;               /* Lenght of data following */
 371 };
 372
 373 struct smu_user_reply_hdr
 374 {
 375         __u32           status;                 /* Command status */
 376         __u32           reply_len;              /* Lenght of data follwing */
 377 };
 378
 379 #endif /*  _SMU_H */