include/linux/brcmphy.h

   1 #ifndef _LINUX_BRCMPHY_H
   2 #define _LINUX_BRCMPHY_H
   3
   4 #define PHY_ID_BCM50610                 0x0143bd60
   5 #define PHY_ID_BCM50610M                0x0143bd70
   6 #define PHY_ID_BCM5241                  0x0143bc30
   7 #define PHY_ID_BCMAC131                 0x0143bc70
   8 #define PHY_ID_BCM5481                  0x0143bca0
   9 #define PHY_ID_BCM5482                  0x0143bcb0
  10 #define PHY_ID_BCM5411                  0x00206070
  11 #define PHY_ID_BCM5421                  0x002060e0
  12 #define PHY_ID_BCM5464                  0x002060b0
  13 #define PHY_ID_BCM5461                  0x002060c0
  14 #define PHY_ID_BCM57780                 0x03625d90
  15
  16 #define PHY_ID_BCM7366                  0x600d8490
  17 #define PHY_ID_BCM7439                  0x600d8480
  18 #define PHY_ID_BCM7445                  0x600d8510
  19
  20 #define PHY_BCM_OUI_MASK                0xfffffc00
  21 #define PHY_BCM_OUI_1                   0x00206000
  22 #define PHY_BCM_OUI_2                   0x0143bc00
  23 #define PHY_BCM_OUI_3                   0x03625c00
  24 #define PHY_BCM_OUI_4                   0x600d8400
  25 #define PHY_BCM_OUI_5                   0x03625e00
  26 #define PHY_BCM_OUI_6                   0xae025000
  27
  28 #define PHY_BCM_FLAGS_MODE_COPPER       0x00000001
  29 #define PHY_BCM_FLAGS_MODE_1000BX       0x00000002
  30 #define PHY_BCM_FLAGS_INTF_SGMII        0x00000010
  31 #define PHY_BCM_FLAGS_INTF_XAUI         0x00000020
  32 #define PHY_BRCM_WIRESPEED_ENABLE       0x00000100
  33 #define PHY_BRCM_AUTO_PWRDWN_ENABLE     0x00000200
  34 #define PHY_BRCM_RX_REFCLK_UNUSED       0x00000400
  35 #define PHY_BRCM_STD_IBND_DISABLE       0x00000800
  36 #define PHY_BRCM_EXT_IBND_RX_ENABLE     0x00001000
  37 #define PHY_BRCM_EXT_IBND_TX_ENABLE     0x00002000
  38 #define PHY_BRCM_CLEAR_RGMII_MODE       0x00004000
  39 #define PHY_BRCM_DIS_TXCRXC_NOENRGY     0x00008000
  40 /* Broadcom BCM7xxx specific workarounds */
  41 #define PHY_BRCM_100MBPS_WAR            0x00010000
  42 #define PHY_BCM_FLAGS_VALID             0x80000000
  43
  44 /* Broadcom BCM54XX register definitions, common to most Broadcom PHYs */
  45 #define MII_BCM54XX_ECR         0x10    /* BCM54xx extended control register */
  46 #define MII_BCM54XX_ECR_IM      0x1000  /* Interrupt mask */
  47 #define MII_BCM54XX_ECR_IF      0x0800  /* Interrupt force */
  48
  49 #define MII_BCM54XX_ESR         0x11    /* BCM54xx extended status register */
  50 #define MII_BCM54XX_ESR_IS      0x1000  /* Interrupt status */
  51
  52 #define MII_BCM54XX_EXP_DATA    0x15    /* Expansion register data */
  53 #define MII_BCM54XX_EXP_SEL     0x17    /* Expansion register select */
  54 #define MII_BCM54XX_EXP_SEL_SSD 0x0e00  /* Secondary SerDes select */
  55 #define MII_BCM54XX_EXP_SEL_ER  0x0f00  /* Expansion register select */
  56
  57 #define MII_BCM54XX_AUX_CTL     0x18    /* Auxiliary control register */
  58 #define MII_BCM54XX_ISR         0x1a    /* BCM54xx interrupt status register */
  59 #define MII_BCM54XX_IMR         0x1b    /* BCM54xx interrupt mask register */
  60 #define MII_BCM54XX_INT_CRCERR  0x0001  /* CRC error */
  61 #define MII_BCM54XX_INT_LINK    0x0002  /* Link status changed */
  62 #define MII_BCM54XX_INT_SPEED   0x0004  /* Link speed change */
  63 #define MII_BCM54XX_INT_DUPLEX  0x0008  /* Duplex mode changed */
  64 #define MII_BCM54XX_INT_LRS     0x0010  /* Local receiver status changed */
  65 #define MII_BCM54XX_INT_RRS     0x0020  /* Remote receiver status changed */
  66 #define MII_BCM54XX_INT_SSERR   0x0040  /* Scrambler synchronization error */
  67 #define MII_BCM54XX_INT_UHCD    0x0080  /* Unsupported HCD negotiated */
  68 #define MII_BCM54XX_INT_NHCD    0x0100  /* No HCD */
  69 #define MII_BCM54XX_INT_NHCDL   0x0200  /* No HCD link */
  70 #define MII_BCM54XX_INT_ANPR    0x0400  /* Auto-negotiation page received */
  71 #define MII_BCM54XX_INT_LC      0x0800  /* All counters below 128 */
  72 #define MII_BCM54XX_INT_HC      0x1000  /* Counter above 32768 */
  73 #define MII_BCM54XX_INT_MDIX    0x2000  /* MDIX status change */
  74 #define MII_BCM54XX_INT_PSERR   0x4000  /* Pair swap error */
  75
  76 #define MII_BCM54XX_SHD         0x1c    /* 0x1c shadow registers */
  77 #define MII_BCM54XX_SHD_WRITE   0x8000
  78 #define MII_BCM54XX_SHD_VAL(x)  ((x & 0x1f) << 10)
  79 #define MII_BCM54XX_SHD_DATA(x) ((x & 0x3ff) << 0)
  80
  81 /*
  82  * AUXILIARY CONTROL SHADOW ACCESS REGISTERS.  (PHY REG 0x18)
  83  */
  84 #define MII_BCM54XX_AUXCTL_SHDWSEL_AUXCTL       0x0000
  85 #define MII_BCM54XX_AUXCTL_ACTL_TX_6DB          0x0400
  86 #define MII_BCM54XX_AUXCTL_ACTL_SMDSP_ENA       0x0800
  87
  88 #define MII_BCM54XX_AUXCTL_MISC_WREN    0x8000
  89 #define MII_BCM54XX_AUXCTL_MISC_FORCE_AMDIX     0x0200
  90 #define MII_BCM54XX_AUXCTL_MISC_RDSEL_MISC      0x7000
  91 #define MII_BCM54XX_AUXCTL_SHDWSEL_MISC 0x0007
  92
  93 #define MII_BCM54XX_AUXCTL_SHDWSEL_AUXCTL       0x0000
  94
  95 /*
  96  * Broadcom LED source encodings.  These are used in BCM5461, BCM5481,
  97  * BCM5482, and possibly some others.
  98  */
  99 #define BCM_LED_SRC_LINKSPD1    0x0
 100 #define BCM_LED_SRC_LINKSPD2    0x1
 101 #define BCM_LED_SRC_XMITLED     0x2
 102 #define BCM_LED_SRC_ACTIVITYLED 0x3
 103 #define BCM_LED_SRC_FDXLED      0x4
 104 #define BCM_LED_SRC_SLAVE       0x5
 105 #define BCM_LED_SRC_INTR        0x6
 106 #define BCM_LED_SRC_QUALITY     0x7
 107 #define BCM_LED_SRC_RCVLED      0x8
 108 #define BCM_LED_SRC_MULTICOLOR1 0xa
 109 #define BCM_LED_SRC_OPENSHORT   0xb
 110 #define BCM_LED_SRC_OFF         0xe     /* Tied high */
 111 #define BCM_LED_SRC_ON          0xf     /* Tied low */
 112
 113
 114 /*
 115  * BCM5482: Shadow registers
 116  * Shadow values go into bits [14:10] of register 0x1c to select a shadow
 117  * register to access.
 118  */
 119 /* 00101: Spare Control Register 3 */
 120 #define BCM54XX_SHD_SCR3                0x05
 121 #define  BCM54XX_SHD_SCR3_DEF_CLK125    0x0001
 122 #define  BCM54XX_SHD_SCR3_DLLAPD_DIS    0x0002
 123 #define  BCM54XX_SHD_SCR3_TRDDAPD       0x0004
 124
 125 /* 01010: Auto Power-Down */
 126 #define BCM54XX_SHD_APD                 0x0a
 127 #define  BCM54XX_SHD_APD_EN             0x0020
 128
 129 #define BCM5482_SHD_LEDS1       0x0d    /* 01101: LED Selector 1 */
 130                                         /* LED3 / ~LINKSPD[2] selector */
 131 #define BCM5482_SHD_LEDS1_LED3(src)     ((src & 0xf) << 4)
 132                                         /* LED1 / ~LINKSPD[1] selector */
 133 #define BCM5482_SHD_LEDS1_LED1(src)     ((src & 0xf) << 0)
 134 #define BCM54XX_SHD_RGMII_MODE  0x0b    /* 01011: RGMII Mode Selector */
 135 #define BCM5482_SHD_SSD         0x14    /* 10100: Secondary SerDes control */
 136 #define BCM5482_SHD_SSD_LEDM    0x0008  /* SSD LED Mode enable */
 137 #define BCM5482_SHD_SSD_EN      0x0001  /* SSD enable */
 138 #define BCM5482_SHD_MODE        0x1f    /* 11111: Mode Control Register */
 139 #define BCM5482_SHD_MODE_1000BX 0x0001  /* Enable 1000BASE-X registers */
 140
 141
 142 /*
 143  * EXPANSION SHADOW ACCESS REGISTERS.  (PHY REG 0x15, 0x16, and 0x17)
 144  */
 145 #define MII_BCM54XX_EXP_AADJ1CH0                0x001f
 146 #define  MII_BCM54XX_EXP_AADJ1CH0_SWP_ABCD_OEN  0x0200
 147 #define  MII_BCM54XX_EXP_AADJ1CH0_SWSEL_THPF    0x0100
 148 #define MII_BCM54XX_EXP_AADJ1CH3                0x601f
 149 #define  MII_BCM54XX_EXP_AADJ1CH3_ADCCKADJ      0x0002
 150 #define MII_BCM54XX_EXP_EXP08                   0x0F08
 151 #define  MII_BCM54XX_EXP_EXP08_RJCT_2MHZ        0x0001
 152 #define  MII_BCM54XX_EXP_EXP08_EARLY_DAC_WAKE   0x0200
 153 #define MII_BCM54XX_EXP_EXP75                   0x0f75
 154 #define  MII_BCM54XX_EXP_EXP75_VDACCTRL         0x003c
 155 #define  MII_BCM54XX_EXP_EXP75_CM_OSC           0x0001
 156 #define MII_BCM54XX_EXP_EXP96                   0x0f96
 157 #define  MII_BCM54XX_EXP_EXP96_MYST             0x0010
 158 #define MII_BCM54XX_EXP_EXP97                   0x0f97
 159 #define  MII_BCM54XX_EXP_EXP97_MYST             0x0c0c
 160
 161 /*
 162  * BCM5482: Secondary SerDes registers
 163  */
 164 #define BCM5482_SSD_1000BX_CTL          0x00    /* 1000BASE-X Control */
 165 #define BCM5482_SSD_1000BX_CTL_PWRDOWN  0x0800  /* Power-down SSD */
 166 #define BCM5482_SSD_SGMII_SLAVE         0x15    /* SGMII Slave Register */
 167 #define BCM5482_SSD_SGMII_SLAVE_EN      0x0002  /* Slave mode enable */
 168 #define BCM5482_SSD_SGMII_SLAVE_AD      0x0001  /* Slave auto-detection */
 169
 170
 171 /*****************************************************************************/
 172 /* Fast Ethernet Transceiver definitions. */
 173 /*****************************************************************************/
 174
 175 #define MII_BRCM_FET_INTREG             0x1a    /* Interrupt register */
 176 #define MII_BRCM_FET_IR_MASK            0x0100  /* Mask all interrupts */
 177 #define MII_BRCM_FET_IR_LINK_EN         0x0200  /* Link status change enable */
 178 #define MII_BRCM_FET_IR_SPEED_EN        0x0400  /* Link speed change enable */
 179 #define MII_BRCM_FET_IR_DUPLEX_EN       0x0800  /* Duplex mode change enable */
 180 #define MII_BRCM_FET_IR_ENABLE          0x4000  /* Interrupt enable */
 181
 182 #define MII_BRCM_FET_BRCMTEST           0x1f    /* Brcm test register */
 183 #define MII_BRCM_FET_BT_SRE             0x0080  /* Shadow register enable */
 184
 185
 186 /*** Shadow register definitions ***/
 187
 188 #define MII_BRCM_FET_SHDW_MISCCTRL      0x10    /* Shadow misc ctrl */
 189 #define MII_BRCM_FET_SHDW_MC_FAME       0x4000  /* Force Auto MDIX enable */
 190
 191 #define MII_BRCM_FET_SHDW_AUXMODE4      0x1a    /* Auxiliary mode 4 */
 192 #define MII_BRCM_FET_SHDW_AM4_LED_MASK  0x0003
 193 #define MII_BRCM_FET_SHDW_AM4_LED_MODE1 0x0001
 194
 195 #define MII_BRCM_FET_SHDW_AUXSTAT2      0x1b    /* Auxiliary status 2 */
 196 #define MII_BRCM_FET_SHDW_AS2_APDE      0x0020  /* Auto power down enable */
 197
 198 /*
 199  * Indirect register access functions for the 1000BASE-T/100BASE-TX/10BASE-T
 200  * 0x1c shadow registers.
 201  */
 202 static inline int bcm54xx_shadow_read(struct phy_device *phydev, u16 shadow)
 203 {
 204         phy_write(phydev, MII_BCM54XX_SHD, MII_BCM54XX_SHD_VAL(shadow));
 205         return MII_BCM54XX_SHD_DATA(phy_read(phydev, MII_BCM54XX_SHD));
 206 }
 207
 208 static inline int bcm54xx_shadow_write(struct phy_device *phydev, u16 shadow,
 209                                        u16 val)
 210 {
 211         return phy_write(phydev, MII_BCM54XX_SHD,
 212                          MII_BCM54XX_SHD_WRITE |
 213                          MII_BCM54XX_SHD_VAL(shadow) |
 214                          MII_BCM54XX_SHD_DATA(val));
 215 }
 216
 217 #define BRCM_CL45VEN_EEE_CONTROL        0x803d
 218 #define LPI_FEATURE_EN                  0x8000
 219 #define LPI_FEATURE_EN_DIG1000X         0x4000
 220
 221 #endif /* _LINUX_BRCMPHY_H */