1 2009-11-24 Joel Brobecker <brobecker@adacore.com>
3 * common/aclocal.m4: Add include of ../../config/zlib.m4.
4 * common/common.m4: Use AM_ZLIB to check for zlib support.
5 * ppc/configure.ac: Likewise.
6 * arm/configure, avr/configure, common/configure, cr16/configure,
7 cris/configure, d10v/configure, erc32/configure, frv/configure,
8 h8300/configure, iq2000/configure, lm32/configure, m32c/configure,
9 m32r/configure, m68hc11/configure, mcore/configure,
10 microblaze/configure, mips/configure, mn10300/configure,
11 moxie/configure, ppc/configure, sh/configure, sh64/configure,
12 v850/configure: Regenerate.
14 2009-11-24 DJ Delorie <dj@redhat.com>
17 * configure.ac: Add entry for Renesas RX.
18 * configure: Regenerate.
20 2009-11-22 Doug Evans <dje@sebabeach.org>
22 * cris/cpuall.h: Regenerate.
23 * cris/cpuv10.h: Regenerate.
24 * cris/cpuv32.h: Regenerate.
25 * cris/decodev10.c: Regenerate.
26 * cris/decodev10.h: Regenerate.
27 * cris/decodev32.c: Regenerate.
28 * cris/decodev32.h: Regenerate.
30 2009-11-12 Tristan Gingold <gingold@adacore.com>
32 * avr/interp.c (sim_write): Allow byte access.
35 2009-11-12 Tristan Gingold <gingold@adacore.com>
37 * avr/interp.c (sim_load): Clear memory before loading.
39 2009-11-09 Tristan Gingold <gingold@adacore.com>
41 * avr/interp.c (sim_resume): Fix typo for OP_ret.
43 2009-10-23 Doug Evans <dje@sebabeach.org>
45 * cris/arch.c: Regenerate.
46 * cris/arch.h: Regenerate.
47 * cris/cpuall.h: Regenerate.
48 * cris/cpuv10.c: Regenerate.
49 * cris/cpuv10.h: Regenerate.
50 * cris/cpuv32.c: Regenerate.
51 * cris/cpuv32.h: Regenerate.
52 * cris/cris-desc.c: Regenerate.
53 * cris/cris-desc.h: Regenerate.
54 * cris/cris-opc.h: Regenerate.
55 * cris/decodev10.c: Regenerate.
56 * cris/decodev10.h: Regenerate.
57 * cris/decodev32.c: Regenerate.
58 * cris/decodev32.h: Regenerate.
59 * cris/modelv10.c: Regenerate.
60 * cris/modelv32.c: Regenerate.
61 * cris/semcrisv10f-switch.c: Regenerate.
62 * cris/semcrisv32f-switch.c: Regenerate.
64 2009-10-22 Tristan Gingold <gingold@adacore.com>
66 * avr/interp.c (sim_stop): Return 1.
68 2009-10-16 Doug Evans <dje@sebabeach.org>
70 * MAINTAINERS: Add myself as m32r maintainer.
72 2009-10-15 Michael Egaer <eager@eagercon.com>
74 * MAINTAINERS: Add self as MicroBlaze maintainer.
76 2009-10-14 Ben Elliston <bje@gnu.org>
78 * MAINTAINERS (common): Move myself to "past maintainers" section.
80 2009-10-06 Michael Eager <eager@eagercon.com>
82 * microblaze/interp.c: Add include microblaze-dis.h.
84 2009-09-23 Michael Eager <eager@eagercon.com>
86 * configure: Add microblaze-*.* (not regenerated).
87 * configure.ac: Likewise.
88 * microblaze/config.in: New.
89 * microblaze/configure: Generate.
90 * microblaze/configure.ac: New.
91 * microblaze/interp.c: New.
92 * microblaze/Makefile.in: New.
93 * microblaze/microblaze.h: New.
94 * microblaze/microblaze.isa: New.
95 * microblaze/sim-main.h: New.
96 * microblaze/sysdep.h: New.
98 2009-08-22 Ralf Wildenhues <Ralf.Wildenhues@gmx.de>
100 * avr/config.in: Regenerate.
101 * avr/configure: Likewise.
102 * configure: Likewise.
103 * cris/config.in: Likewise.
104 * cris/configure: Likewise.
106 * configure.ac: m4_include toplevel config/override.m4.
107 * configure: Regenerate.
108 * avr/configure: Regenerate.
109 * cris/configure: Regenerate.
111 2009-07-30 Ralf Wildenhues <Ralf.Wildenhues@gmx.de>
113 * Makefile.in (datarootdir): New variable.
115 2009-05-18 Jon Beniston <jon@beniston.com>
117 * MAINTAINERS: Add Jon Beniston as maintainer of lm32 sim.
118 * configure.ac: Add lm32 target.
119 * lm32: New directory.
121 2009-05-11 Andrew Cagney <cagney@gnu.org>
123 * MAINTAINERS: Orphan ppc.
125 2009-05-08 Kevin Buettner <kevinb@redhat.com>
127 * m32c/gdb-if.c (m32c_signal_to_host): Rename to
128 m32c_signal_to_target. Change signal return values from SIGILL,
129 SIGTRAP, SIGSEGV, etc. to TARGET_SIGNAL_ILL, TARGET_SIGNAL_TRAP,
130 TARGET_SIGNAL_SEGV, etc. Fix all callers.
132 2009-04-30 Anthony Green <green@moxielogic.com>
134 * MAINTAINERS: Add myself for the moxie port.
135 * moxie: New directory.
136 * configure.ac: Add entry for moxie.
137 * configure: Regenerate.
139 2009-04-27 Tristan Gingold <gingold@adacore.com>
141 * avr: New directory.
142 * avr/interp.c, avr/Makefile.in, avr/configure.ac: New files.
143 * avr/config.in: New file, generated by autoheader.
144 * avr/configure: New file generated by autoconf.
145 * configure.ac: Add avr.
146 * configure: Regenerated.
148 2009-04-17 Carlos O'Donell <carlos@codesourcery.com>
150 * Makefile.in: Add dummy install-pdf, html, and
151 install-html targets.
153 2009-01-18 Hans-Peter Nilsson <hp@axis.com>
155 * cris/sim-if.c: Include errno.h.
156 (cris_start_address, cris_program_offset): New variables.
157 (OPTION_CRIS_PROGRAM_OFFSET, OPTION_CRIS_STARTADDR): New option
159 (cris_options): New options --cris-program-offset and
160 --cris-start-address.
161 (cris_option_handler): Handle new options.
162 (cris_program_offset_write, cris_set_section_offset_iterator)
163 (cris_offset_sections, cris_offset_sections): New functions.
164 (sim_load): Use cris_program_offset_write as function argument to
165 cris_load_elf_file, not sim_write.
166 (struct offsetinfo): New struct.
167 (cris_handle_interpreter): Fix typo in comment.
168 (sim_open): Call cris_offset_sections as soon as the bfd of the
169 infile is available. Gate bfd validity checks on abfd non-NULL.
170 (sim_create_inferior): Let cris_start_address when != -1 override
171 other start-address choices.
173 2009-01-06 Hans-Peter Nilsson <hp@axis.com>
175 * cris/traps.c (abort): Define to call sim_io_error.
176 (create_map): Make -1 imply a non-fixed address, not 0. All
177 callers changed. Only prefer the next higher unmapped address if
178 the last mapped address is no less than 0x40000000. Check that
179 the address to be mapped is not already mapped. Update head
181 (unmap_pages): Don't call abort when recursive call fails, just
182 note and return an error if a page in the range couldn't be unmapped.
183 (cris_bmod_handler, h_supr_set_handler, h_supr_get_handler)
184 (schedule, make_first_thread, cris_pipe_empty): New local variable sd.
185 (cris_break_13_handler) <case TARGET_SYS_mmap2>: Handle
186 non-MAP_FIXED argument overlapping existing map. For MAP_FIXED,
187 don't abort on page not being mapped. Handle non-anon filemap
188 with length padded to pagesize.
190 2009-01-03 Hans-Peter Nilsson <hp@axis.com>
192 * cris/sim-if.c (TARGET_AT_NULL, TARGET_AT_PHDR, TARGET_AT_PHENT)
193 (TARGET_AT_PHNUM, TARGET_AT_PAGESZ, TARGET_AT_BASE)
194 (TARGET_AT_FLAGS, TARGET_AT_ENTRY, TARGET_AT_UID, TARGET_AT_EUID)
195 (TARGET_AT_GID, TARGET_AT_EGID, TARGET_AT_HWCAP)
196 (TARGET_AT_CLKTCK): Remove redundant macros.
197 (AUX_ENT): Adjust to use standard ELF AT_* macros.
198 (AUX_ENTF): Ditto. Remove always-0 middle argument. Update all
200 (sim_open): Also pass AT_SECURE.
202 * cris/sim-main.h (struct _sim_cpu): New member
203 set_target_thread_data.
204 * cris/crisv32f.c (CRIS_TLS_REGISTER): Define.
205 * cris/crisv10f.c: Ditto.
206 * cris/cris-tmpl.c (MY (set_target_thread_data)): New function.
207 (MY (f_specific_init)): Set new _sim_cpu member to new function.
208 * cris/traps.c (TARGET_SYS_set_thread_area): Define.
209 (cris_break_13_handler) <case TARGET_SYS_set_thread_area>: New
212 * cris/traps.c (TARGET_SYS_exit_group): Define.
213 (cris_break_13_handler): Handle it like the exit for the last
216 * cris/traps.c (TARGET_UTSNAME): Update to 2009-01-01.
217 (TARGET_EPOCH): Update to match TARGET_UTSNAME. Correct comment.
218 (cris_break_13_handler) <case TARGET_SYS_uname>: Update to
219 2.6.27. Set machine field to the BFD printable name of the
222 * cris/traps.c (TARGET_MAP_DENYWRITE): Define.
223 (cris_break_13_handler) <case TARGET_SYS_mmap2>: Handle
224 TARGET_MAP_DENYWRITE.
226 * cris/traps.c (TARGET_SYS_access, TARGET_R_OK, TARGET_W_OK)
227 (TARGET_X_OK, TARGET_F_OK): Define.
228 (cris_break_13_handler) <case TARGET_SYS_access>: New case.
230 * cris/semcrisv32f-switch.c: Regenerate.
232 2008-12-30 Hans-Peter Nilsson <hp@axis.com>
234 * cris/sim-if.c (sim_open): If sim_analyze_program fails, emit
235 just a short CRIS-specific notice. Tweak the wording for a
236 failing architecture test.
238 * cris/traps.c (TARGET_SYS_writev): New macro.
239 (is_mapped_only, cris_dump_map): New functions.
240 (cris_break_13_handler) <case TARGET_SYS_mmap2>: Handle more flags
241 and prot combinations and a non-zero page-offset. If
242 TARGET_MAP_FIXED, unmap pages before mapping them.
243 <case TARGET_SYS_mprotect>: When checking, allow any length
244 argument. Don't actually do anything.
245 <case TARGET_SYS_writev>: New case.
247 * cris/Makefile.in (SIM_OBJS): Remove sim-hload.o.
248 * cris/sim-if.c: Include elf-bfd.h.
249 (struct progbounds): New members end_loadmem, start_nonloadmem.
250 (xprintf, eprintf): New functions, copied from common/sim-load.c.
251 (cris_load_elf_file, sim_load, cris_get_progbounds): New functions.
252 (get_progbounds_iterator): Renamed from get_progbounds. Make
253 static. Update head comment. Set new struct progbounds members.
254 (exec_load_addr, interp_load_addr, interp_start_addr): New static
256 (aux_ent_phdr, aux_ent_phent, aux_ent_phnum, aux_ent_base)
257 (aux_ent_entry, cris_write_interp, cris_handle_interpreter): New
259 (sim_open): New constant array auxv_entries. Rewrite AUX_ENT
260 handling to use auxv_entries. Improve error message and checking
261 for invalid programs. Use new variable abfd for the program
262 instead of for each access reaching into sd to get it.
263 (sim_create_inferior): If non-zero, use interp_start_addr instead
264 of the program start address.
265 (cris_disassemble_insn): Remove incorrect and unclear, supposedly
266 stale comment. Always specify little-endian.
268 2008-07-29 Nick Clifton <nickc@redhat.com>
270 * common/genmloop.sh: Add new parameter: -shell to specify the
271 command interpreter to use to run the input file. This is
272 necessary because otherwise SHELL is taken from the user's
273 environment, and not from the makefile that invoked this script
274 and the user might not be running an sh-like shell.
275 * cris/Makefile.in: Pass -shell parameter to genmloop.sh.
276 * fr30/Makefile.in: Likewise.
277 * frv/Makefile.in: Likewise.
278 * i960/Makefile.in: Likewise.
279 * iq2000/Makefile.in: Likewise.
280 * m32r/Makefile.in: Likewise.
282 * frv/mloop.in: Add missing start of line comment marker.
284 2008-07-11 Hans-Peter Nilsson <hp@axis.com>
286 * cris/configure: Regenerate to track ../common/common.m4 changes.
287 * cris/config.in: Ditto.
289 2008-06-06 Vladimir Prus <vladimir@codesourcery.com>
290 Daniel Jacobowitz <dan@codesourcery.com>
291 Joseph Myers <joseph@codesourcery.com>
293 * cris/configure: Regenerate.
295 2008-05-09 Olivier Hainque <hainque@adacore.com>
297 * ppc/altivec.igen (vperm): Latch inputs into temporaries.
299 2008-03-25 M R Swami Reddy <MR.Swami.Reddy@nsc.com>
301 * MAINTAINERS: Add myself as maintainer of cr16 port.
303 2008-02-12 M Ranga Swami Reddy <MR.Swami.Reddy@nsc.com>
305 Add simulator for National cr16 processor.
306 * cr16: New directory.
307 * configure.ac: Add entry for National cr16.
308 * configure: Regenerate.
310 2008-02-05 DJ Delorie <dj@redhat.com>
312 * configure.ac (v850): V850 now has a testsuite.
313 * configure (v850): Likewise.
315 2008-01-01 Daniel Jacobowitz <dan@codesourcery.com>
317 Updated copyright notices for most files.
319 2007-12-19 DJ Delorie <dj@redhat.com>
321 * frv/frv.c (frvbf_cut): Only look at the six LSBs of
324 2007-10-22 Hans-Peter Nilsson <hp@axis.com>
326 * cris/arch.c, cris/arch.h, cris/cpuall.h, cris/cpuv10.c,
327 cris/cpuv10.h, cris/cpuv32.c, cris/cpuv32.h, cris/cris-desc.c,
328 cris/cris-desc.h, cris/cris-opc.h, cris/decodev10.c,
329 cris/decodev10.h, cris/decodev32.c, cris/decodev32.h,
330 cris/modelv10.c, cris/modelv32.c, cris/semcrisv10f-switch.c,
331 cris/semcrisv32f-switch.c: Regenerate.
333 2007-08-24 Joel Brobecker <brobecker@adacore.com>
335 Switch the license of all files explicitly copyright the FSF
338 2007-03-27 Brooks Moses <brooks.moses@codesourcery.com>
340 * Makefile.in: Add dummy "pdf" target.
342 2007-02-20 Hans-Peter Nilsson <hp@axis.com>
344 * cris/traps.c (dump_statistics): Change format for cycle numbers
345 to %llu and cast parameters to unsigned long long.
347 2007-02-16 Thiemo Seufer <ths@mips.com>
349 * Makefile.in (FLAGS_TO_PASS, TARGET_FLAGS_TO_PASS): Add RUNTEST.
351 2007-01-28 Manuel Lauss <slauss@resi.at>
353 * configure.ac (sh64-*-*): Change to sh64*-*-*.
354 (sh-*-*): Change to sh*-*-*.
355 * configure: Regenerated.
357 2007-01-09 Daniel Jacobowitz <dan@codesourcery.com>
359 Updated copyright notices for most files.
361 2006-12-20 Hans-Peter Nilsson <hp@axis.com>
363 * Makefile.in (autoconf-common autoheader-common): Only run
364 autoheader on subdirs with a file config.in.
366 * configure.ac (common): Make the default "yes" for all targets
368 * configure: Regenerate.
370 * Makefile.in (autoconf-common autoheader-common): In documented
371 usage, say SHELL=/bin/sh.
372 (.PHONY): Add autoheader-common.
374 * MAINTAINERS: Add self as authorized committer for *.
376 2006-10-02 Edgar E. Iglesias <edgar@axis.com>
377 Hans-Peter Nilsson <hp@axis.com>
379 * cris/cris-sim.h (enum cris_unknown_syscall_action_type)
380 (cris_unknown_syscall_action): Declare.
381 * cris/sim-if.c (cris_unknown_syscall_action): Define.
382 (cris_options): Add cris-unknown-syscall option.
383 (cris_option_handler): Correct comment about and error message for
384 invalid --cris-cycles argument. Handle --cris-unknown-syscall.
385 * cris/traps.c: Include stdarg.h
386 (cris_unknown_syscall): New function.
387 (cris_break_13_handler): Instead of sim_io_eprintf and
388 sim_engine_halt, call cris_unknown_syscall to handle more or less
389 unknown syscalls. Adjust code as necessary to handle return
392 2006-09-30 Daniel Jacobowitz <dan@codesourcery.com>
394 * MAINTAINERS: Add Dave Brolley for sh64.
396 2006-09-30 Hans-Peter Nilsson <hp@axis.com>
398 * cris/traps.c (TARGET_PIPE_BUF): New macro.
399 (cris_pipe_empty): Correct initialization of "remaining". Only
400 adjust the "write" return value if more than TARGET_PIPE_BUF bytes
403 2006-09-29 Hans-Peter Nilsson <hp@axis.com>
405 * cris/configure.ac: Check for limits.h and sys/param.h.
406 * cris/configure, cris/config.in: Rebuild.
407 * cris/traps.c (SIM_PATHMAX): New macro.
408 (cris_break_13_handler): Use SIM_PATHMAX, not MAXPATHLEN.
410 2006-08-08 Joel Sherrill <joel.sherrill@oarcorp.com>
412 * configure.ac (sparc-*-rtems*|sparc-*-elf*): Enable erc32 simulator.
413 * Makefile.in (FLAGS_TO_PASS): Include libdir.
414 * configure: Regenerated.
416 2006-06-05 Daniel Jacobowitz <dan@codesourcery.com>
418 * cris/configure: Regenerated.
420 2006-05-31 Daniel Jacobowitz <dan@codesourcery.com>
422 * cris/configure: Regenerated.
424 2006-05-05 Andreas Schwab <schwab@suse.de>
426 * configure.ac (CFLAGS_FOR_BUILD): Set and substitute.
427 * configure: Regenerate.
429 * Makefile.in (CFLAGS_FOR_BUILD): Define.
430 (CC_FOR_BUILD): Don't override.
431 (FLAGS_TO_PASS): Pass CFLAGS_FOR_BUILD.
433 2006-05-04 Daniel Jacobowitz <dan@codesourcery.com>
435 * MAINTAINERS: Add an "Authorized committers" section, and list
438 2006-04-08 Hans-Peter Nilsson <hp@axis.com>
440 * cris/crisv32f.c (MY (deliver_interrupt)): Set CCS to new_ccs.
442 2006-04-03 Hans-Peter Nilsson <hp@axis.com>
444 * cris/dv-cris.c, cris/dv-rv.c, cris/rvdummy.c: New files.
445 * cris/Makefile.in (CONFIG_DEVICES): Remove redundant setting.
446 (dv-cris.o, dv-rv.o rvdummy$(EXEEXT), rvdummy.o): New rules.
447 (all): Depend on rvdummy$(EXEEXT).
448 * cris/configure.ac: Call SIM_AC_OPTION_WARNINGS. Check for
449 sys/socket.h and sys/select.h. Call SIM_AC_OPTION_HARDWARE,
451 * cris/configure: Regenerate.
452 * cris/cris-sim.h (cris_have_900000xxif): Declare here.
453 (enum cris_interrupt_type, crisv10deliver_interrupt)
454 (crisv32deliver_interrupt: New declarations.
455 * cris/cris-tmpl.c [WITH_HW] (MY (f_model_insn_after)): Call
456 sim_events_tickn and set state-events member work_pending when it's
457 time for the next event.
458 [WITH_HW] (MY (f_specific_init)): Set CPU-model-specific
459 interrupt-delivery function.
460 * cris/crisv10f.c (MY (deliver_interrupt)): New function.
461 * cris/crisv32f.c (MY (deliver_interrupt)): New function.
462 * cris/devices.c: Include hw-device.h.
463 (device_io_read_buffer) [WITH_HW]: Call hw_io_read_buffer.
464 (device_io_write_buffer): Only perform 0x900000xx-functions if
465 cris_have_900000xxif is nonzero. Else if WITH_HW defined,
466 call hw_io_write_buffer. Add return 0 last in function.
467 * cris/sim-if.c (cris_have_900000xxif): Now global.
468 (sim_open) [WITH_HW]: Clear deliver_interrupt cpu member.
469 Force "-model" option, effectively.
470 * cris/sim-main.h (cris_interrupt_delivery_fn): New type.
471 (struct _sim_cpu) [WITH_HW]: New member deliver_interrupt.
473 2006-04-02 Hans-Peter Nilsson <hp@axis.com>
475 * cris/Makefile.in (CRISV10F_OBJS): Remove semcrisv10f-switch.o.
476 (CRISV32F_OBJS): Remove semcrisv32f-switch.o.
477 (semcrisv10f-switch.o, semcrisv32f-switch.o: Remove dependency rules.
479 2006-03-13 DJ Delorie <dj@redhat.com>
481 * MAINTAINERS: Add self as m32c sim maintainer.
483 2006-02-23 Hans-Peter Nilsson <hp@axis.com>
485 * cris/traps.c (syscall_map): Remove CB_SYS_time / TARGET_SYS_time
487 (cris_break_13_handler) <case TARGET_SYS_time>: New case.
489 2006-01-23 Jim Blandy <jimb@redhat.com>
491 Add simulator for Renesas M32C and M16C.
493 * m32c: New directory.
494 * configure.ac: Add entry for Renesas M32C.
495 * configure: Regenerate.
497 2006-01-10 Hans-Peter Nilsson <hp@axis.com>
499 * cris/cris-tmpl.c (MY (f_model_insn_before)): Only display basic
500 cycle count for the current insn.
502 2005-12-06 Hans-Peter Nilsson <hp@axis.com>
504 * cris/cpuv10.h, cris/cpuv32.h, cris/cris-desc.c, cris/cris-opc.h,
505 cris/decodev10.c, cris/decodev10.h, cris/decodev32.c,
506 cris/decodev32.h, cris/modelv10.c, cris/modelv32.c,
507 cris/semcrisv10f-switch.c, cris/semcrisv32f-switch.c: Regenerate.
509 2005-12-05 Hans-Peter Nilsson <hp@axis.com>
511 * cris/arch.c, cris/arch.h, cris/cpuall.h, cris/cpuv10.c,
512 cris/cpuv10.h, cris/cpuv32.c, cris/cpuv32.h, cris/cris-desc.c,
513 cris/cris-desc.h, cris/cris-opc.h, cris/decodev10.c,
514 cris/decodev10.h, cris/decodev32.c, cris/decodev32.h,
515 cris/modelv10.c, cris/modelv32.c, cris/semcrisv10f-switch.c,
516 cris/semcrisv32f-switch.c: Regenerate.
518 2005-11-20 Hans-Peter Nilsson <hp@axis.com>
520 * cris/traps.c (TARGET_O_RDONLY, TARGET_O_WRONLY): Define.
521 (open_map): Use TARGET_O_ACCMODE, TARGET_O_RDONLY and
523 (cris_break_13_handler) <case TARGET_SYS_fcntl>: Add support for
524 F_GETFL on fd 0, 1 and 2.
526 2005-11-17 Hans-Peter Nilsson <hp@axis.com>
528 * cris/sim-main.h (struct _sim_cpu): New members last_syscall,
529 last_open_fd, last_open_flags.
530 * cris/traps.c: Don't include targ-vals.h.
531 (TARGET_O_ACCMODE): Define.
532 (cris_break_13_handler): Set new _sim_cpu members.
533 <case TARGET_SYS_fcntl>: Support special case of F_GETFL.
534 Rearrange code as switch. Emit "unimplemented" abort for
535 unimplemented fcntl calls.
537 * cris/traps.c (TARGET_SYS_stat): Define.
538 (syscall_stat32_map): Add entry for TARGET_SYS_stat.
539 (cris_break_13_handler) <case TARGET_SYS_stat>: New case.
541 2005-11-16 Hans-Peter Nilsson <hp@axis.com>
543 * cris/cris-tmpl.c (MY (f_model_insn_before)): Make sure only the
544 low 32 bits are used after an unsigned long cast.
546 2005-05-28 Hans-Peter Nilsson <hp@axis.com>
548 * cris/Makefile.in (stamp-v32fmloop): Depend on stamp-v10fmloop.
550 2005-05-26 Chris Demetriou <cgd@netbsd.org>
552 * MAINTAINERS: Update my mail address, move myself to the
553 "Past maintainers" section.
555 2005-05-17 Corinna Vinschen <vinschen@redhat.com>
557 * configure.ac: Add igen to v850 build.
558 * configure: Regenerate.
560 2005-04-29 Paul Brook <paul@codesourcery.com>
562 * common/callback.c (PIPE_BUF): Provide default definition.
563 (os_lstat): Use stat if lstat is not available on the host.
564 (os_ftruncate): Return EINVAL if not available on the host.
565 (os_truncate): Ditto.
566 * common/configure.ac: Check for lstat, truncate and ftruncate.
567 * common/configure: Regenerate.
568 * common/config.in: Regenerate.
570 2005-04-27 Paul Brook <paul@codesourcery.com>
572 * common/Make-common.in: Add $(EXEEXT) to "run".
574 2005-04-18 Hans-Peter Nilsson <hp@axis.com>
576 * cris/traps.c (cris_break_13_handler) <case TARGET_SYS_mmap2>:
577 For ((len & 8191) != 0 && fd == (USI) -1), don't say this isn't
578 implemented. In call to create_map, pad length argument to 8k.
580 2005-04-15 Corinna Vinschen <vinschen@redhat.com>
582 * configure.ac: Add explicit sh64 case.
583 * configure: Regenerate.
585 2005-03-30 Paul Brook <paul@codesourcery.com>
587 * arm/wrapper.c: Provide SIGTRAP and SIGBUS.
589 2005-03-24 Hans-Peter Nilsson <hp@axis.com>
591 * cris/Makefile.in (stamp-v10fcpu, stamp-v32fcpu): Add kludge to
592 include cgen-ops.h in decodev10.c and decodev32.c.
593 * cris/sim-main.h: Don't include cgen-ops.h here.
594 * cris/arch.c, cris/arch.h, cris/cpuall.h, cris/cpuv10.c,
595 cris/cpuv10.h, cris/cpuv32.c, cris/cpuv32.h, cris/cris-desc.c,
596 cris/cris-desc.h, cris/cris-opc.h, cris/decodev10.c,
597 cris/decodev10.h, cris/decodev32.c, cris/decodev32.h,
598 cris/modelv10.c, cris/modelv32.c, cris/semcrisv10f-switch.c,
599 cris/semcrisv32f-switch.c: Regenerate.
601 * cris/traps.c (cris_break_13_handler) <case
602 TARGET_SYS_rt_sigaction>: Rename sa_handler, sa_flags,
603 sa_restorer, sa_mask_low, sa_mask_high to target_sa_handler etc.
605 2005-03-23 Mark Kettenis <kettenis@gnu.org>
607 * cris/configure: Regenerate.
609 2005-02-28 Jim Blandy <jimb@redhat.com>
611 * d10v/configure.ac, igen/configure.ac, m68hc11/configure.ac,
612 mips/configure.ac, mn10300/configure.ac, v850/configure.ac:
613 Regenerated, after change to common/aclocal.m4.
615 2005-02-18 Corinna Vinschen <vinschen@redhat.com>
617 * iq2000: New target subdirectory.
618 * configure.ac: Add iq2000 target.
619 * configure: Regenerate.
621 2005-01-29 Hans-Peter Nilsson <hp@axis.com>
623 * Makefile.in (all, clean mostlyclean, distclean maintainer-clean)
624 (realclean, install): Fail if subdir make failed.
626 2005-01-28 Hans-Peter Nilsson <hp@axis.com>
628 * cris: New directory, simulator for Axis Communications CRIS
629 including CRIS v32, CGEN-based.
630 * configure.ac: Add corresponding configury.
631 * configure: Regenerate.
633 2005-01-17 Andrew Cagney <cagney@gnu.org>
635 * configure.ac: For mips*-*-* and mn10300*-*-* configure the
636 common directory. Remove sparc*-*-* from list.
638 2005-01-11 Andrew Cagney <cagney@gnu.org>
640 * Makefile.in (autoconf-common autoheader-common): Add --force to
641 autoconf and autoheader.
642 (autoconf-common autoheader-common)
643 (autoconf-install autoheader-install): Check for configure.ac, not
645 * configure.ac: Delete AC_CONFIG_AUX_DIR.
646 * configure: Re-generate.
648 2005-01-07 Andrew Cagney <cagney@gnu.org>
650 * configure.ac: Replace configure.in. Requires autoconf 2.59 and
651 correctly calls AC_CONFIG_SUBDIRS.
652 * configure: Re-generate.
654 2004-12-01 Andrew Cagney <cagney@gnu.org>
656 * i960, h8500: Delete directory.
658 2004-11-12 Andrew Cagney <cagney@gnu.org>
660 * d30v, fr30, mn10200, z8k: Delete directory.
662 2004-03-10 Ben Elliston <bje@gnu.org>
664 * MAINTAINERS: Update my mail address.
666 2004-01-26 Chris Demetriou <cgd@broadcom.com>
668 * configure.in (mips*-*-*): Configure in testsuite.
669 * configure: Regenerate.
671 2003-10-08 Dave Brolley <brolley@redhat.com>
673 * configure.in: Move frv handling to alphabetically correct placement.
675 2003-09-03 Andreas Schwab <schwab@suse.de>
677 * Makefile.in (FLAGS_TO_PASS): Pass down $(bindir) and $(mandir).
679 2003-08-29 Dave Brolley <brolley@redhat.com>
681 * MAINTAINERS: Add myself as maintainer of the FRV port.
683 2003-08-20 Michael Snyder <msnyder@redhat.com>
684 Dave Brolley <brolley@redhat.com>
686 * frv/: New directory, simulator for the Fujitsu FRV.
687 * configure.in: Add frv configury.
688 * configure: Regenerate.
690 2003-08-10 Ben Elliston <bje@wasabisystems.com>
692 * MAINTAINERS: Update my mail address.
694 2003-08-09 Andrew Cagney <cagney@redhat.com>
696 * MAINTAINERS: Andrew Cagney (mips) and Geoff Keating (ppc) drop
697 maintenance. List igen and sh maintainers. Mention that target
698 and global maintainers pick up the slack.
700 2003-07-09 Michael Snyder <msnyder@redhat.com>
702 * configure.in: Add testsuite to extra_subdirs for sh.
703 * configure: Regenerate.
705 2003-01-23 Nick Clifton <nickc@redhat.com>
709 2002-04-02 Alexandre Oliva <aoliva@redhat.com>
711 * sh/gencode.c: Replace sh3e with sh2e except in fsqrt.
713 2002-08-24 Geoffrey Keating <geoffk@redhat.com>
715 * MAINTAINERS: Update my email address.
717 2002-07-17 Andrew Cagney <ac131313@redhat.com>
719 * w65/: Delete directory.
721 2002-07-16 Andrew Cagney <ac131313@redhat.com>
723 * configure.in (extra_subdirs): Mark fr30-*-* as obsolete.
724 * configure: Re-generate.
726 2002-07-13 Andrew Cagney <ac131313@redhat.com>
728 * configure.in (extra_subdirs): Mark d30v-*-* as obsolete.
729 * configure: Re-generate.
731 2002-06-16 Andrew Cagney <ac131313@redhat.com>
733 * Makefile.in (autoconf-changelog autoheader-changelog): Let name,
734 id, date and host to be overriden by NAME, ID, DATE and HOST
735 respectfully. Use ISO dates.
737 Thu Jun 6 12:34:13 2002 Andrew Cagney <cagney@redhat.com>
739 * Makefile.in (ChangeLog): New makefile variable.
740 * README-HACKING: Mention the ChangeLog makefile variable.
742 2002-06-01 Andrew Cagney <ac131313@redhat.com>
744 * tic80/: Delete directory.
746 2002-05-16 Stephane Carrez <stcarrez@nerim.fr>
748 * MAINTAINERS: Update my email address.
750 2002-03-06 Stephane Carrez <Stephane.Carrez@worldnet.fr>
752 * MAINTAINERS: Record self as maintainer of m68hc11 simulator.
754 2002-03-01 Frank Ch. Eigler <fche@redhat.com>
756 * MAINTAINERS: Record self as a co-maintainer of just common/.
758 2002-02-07 Nick Clifton <nickc@cambridge.redhat.com>
760 * MAINTAINERS: Point to GDB files describing overall maintaince
761 and check-in procedures.
763 2002-01-10 Nick Clifton <nickc@cambridge.redhat.com>
765 * MAINTAINERS: Add myself for ARM portions.
767 2001-10-19 Andrew Cagney <ac131313@redhat.com>
769 * configure.in: When Linux or NetBSD, enable PowerPC simulator.
770 * configure: Re-generate.
772 2001-02-16 Ben Elliston <bje@redhat.com>
774 * MAINTAINERS: Add myself for common portions.
776 2001-01-15 Chris Demetriou <cgd@broadcom.com>
778 * MAINTAINERS: Added self and Andrew for the mips sim.
780 2000-10-25 Geoff Keating <geoffk@cygnus.com>
782 * MAINTAINERS: Added self and Andrew for the ppc sim.
784 Thu Jul 27 21:26:26 2000 Andrew Cagney <cagney@b1.cygnus.com>
786 From Stephane Carrez <Stephane.Carrez@worldnet.fr>:
787 * m68hc11: New directory.
789 * configure: Regenerate.
791 Tue Jul 4 13:43:54 2000 Andrew Cagney <cagney@b1.cygnus.com>
793 * tic80: New directory.
794 * configure.in: Add configury.
795 * configure: Regenerate.
797 2000-04-20 Nick Clifton <nickc@cygnus.com>
799 * configure.in (extra_subdirs): Add testsuite to strongarm
801 * configure: Regenerate.
803 Sat Mar 4 16:48:54 2000 Andrew Cagney <cagney@b1.cygnus.com>
805 * MAINTAINERS: New file. Blank.
807 1999-11-18 Ben Elliston <bje@cygnus.com>
809 * configure.in: Require autoconf 2.13 and remove obsolete
810 invocation of AC_C_CROSS.
811 * configure: Regenerate.
813 1999-09-29 Doug Evans <devans@casey.cygnus.com>
815 * configure.in: Configure the testsuite directory for thumb.
816 * configure: Regenerate.
818 1999-07-16 Ben Elliston <bje@cygnus.com>
820 * configure.in: Configure the testsuite directory for arm.
821 * configure: Regenerate.
823 1999-04-08 Nick Clifton <nickc@cygnus.com>
825 * configure.in: Add support for MCore target.
826 * configure: Regenerate.
828 1999-03-14 Stan Shebs <shebs@andros.cygnus.com>
830 * Makefile.in (FLAGS_TO_PASS, TARGET_FLAGS_TO_PASS): Remove
831 RUNTEST instead of commenting out, fixes portability problem.
833 1999-02-08 Nick Clifton <nickc@cygnus.com>
835 * configure.in: Add support for StrongARM target.
836 * configure: Regenerate.
838 1999-01-04 Jason Molenda (jsm@bugshack.cygnus.com)
840 * configure.in: Require autoconf 2.12.1 or higher.
842 1998-12-08 James E Wilson <wilson@wilson-pc.cygnus.com>
844 * configure.in (i960-*-*): Add.
845 * configure: Rebuild.
847 Wed Nov 4 19:11:43 1998 Dave Brolley <brolley@cygnus.com>
849 * configure.in: Added case for fr30-*-*.
850 * configure: Regenerated.
852 Fri Sep 25 10:12:19 1998 Christopher Faylor <cgf@cygnus.com>
854 * ppc/Makefile.in: Add EXEEXT to installed powerpc-eabi-run program
855 to allow successful operation on Windows.
857 Thu May 28 14:59:46 1998 Jillian Ye <jillian@cygnus.com>
859 * Makefile.in: Take RUNTEST out of FLAGS_TO_PASS so that make
860 check can be invoked recursively.
862 Wed Apr 29 12:38:53 1998 Mark Alexander <marka@cygnus.com>
864 * configure.in: Build simulator on sparclite and sparc86x targets.
865 * configure: Regenerate.
867 Sun Apr 26 15:21:01 1998 Tom Tromey <tromey@cygnus.com>
869 * Makefile.in (autoconf-common autoheader-common): Don't pass -l
870 to autoconf and autoheader.
872 Fri Apr 24 11:14:13 1998 Tom Tromey <tromey@cygnus.com>
874 * Makefile.in (autoconf-common autoheader-common): Pass `-l
875 ../common' to autoconf and autoheader. Unconditionally run
876 autoconf in every subdir.
877 (autoconf-changelog autoheader-changelog): Unconditionally run
878 commands in every subdir.
879 (autoconf-install autoheader-install): Likewise.
881 Tue Mar 24 17:12:43 1998 Stu Grossman <grossman@bhuna.cygnus.co.uk>
883 * Makefile.in: Get SHELL from configure.
884 * (FLAGS_TO_PASS): Pass down SHELL.
885 * configure: Regenerate with autoconf 2.12.1 to fix shell issues for
888 Tue Mar 24 11::18:00 1998 Joyce Janczyn <janczyn@cygnus.com>
890 * configure.in (extra_subdirs): Enable igen for mn10300.
891 * configure: Re-generate.
893 Tue Dec 2 10:10:42 1997 Nick Clifton <nickc@cygnus.com>
895 * configure.in (extra_subdirs): Add support for thumb target.
897 * configure (extra_subdirs): Add support for thumb target.
899 Wed Oct 8 12:38:48 1997 Andrew Cagney <cagney@b1.cygnus.com>
901 * configure.in (extra_subdirs): Add IGEN directory when MIPS
903 * configure: Regenerate.
905 Fri Sep 12 13:10:31 1997 Andrew Cagney <cagney@b1.cygnus.com>
907 * configure.in (extra_subdirs): v850ea needs igen.
908 * configure: Re-generate.
910 Mon Sep 1 16:48:23 1997 Andrew Cagney <cagney@b1.cygnus.com>
912 * configure.in (testdir): When a testsuite directory, add that to
913 the list of confdirs.
915 Tue Aug 19 11:17:46 1997 Andrew Cagney <cagney@b1.cygnus.com>
917 * configure.in (extra_subdirs): Enable igen ready for V850.
919 Tue Aug 26 15:14:48 1997 Andrew Cagney <cagney@b1.cygnus.com>
921 * configure.in (w65-*-*, only_if_enabled): Set.
922 * configure: Re-generate.
924 Mon Aug 25 16:26:53 1997 Andrew Cagney <cagney@b1.cygnus.com>
926 * configure.in (sparc*-*-*, only_if_enabled): Set
927 only_if_enabled=yes. Check only_if_enabled before enabling a
929 * configure: Regenerate.
931 Mon Aug 18 10:56:59 1997 Nick Clifton <nickc@cygnus.com>
933 * configure.in (extra_subdirs): Add v850e target.
935 Mon Aug 18 10:56:59 1997 Nick Clifton <nickc@cygnus.com>
937 * configure.in (extra_subdirs): Add v850ea target.
939 Fri Jul 25 11:40:47 1997 Doug Evans <dje@canuck.cygnus.com>
941 * configure.in (sparc*-*-*): Don't build erc32.
942 * configure: Regenerate.
944 Thu Apr 24 00:47:20 1997 Doug Evans <dje@canuck.cygnus.com>
946 * configure.in (m32r-*-*): New target.
947 * configure: Regenerate.
949 * Makefile.in (autoconf-common, autoconf-changelog): Change $* to $@.
951 Mon Apr 21 22:57:55 1997 Andrew Cagney <cagney@b1.cygnus.com>
953 * Makefile.in (.NOEXPORT, MAKEOVERRIDES): Moved to end, BSD make
954 thought that .NOEXPORT was the default target.
956 Fri Apr 11 17:18:07 1997 Ian Lance Taylor <ian@cygnus.com>
958 * Makefile.in (clean mostlyclean): Restore targets accidentally
959 deleted in earlier change.
961 Thu Apr 3 12:20:32 1997 Andrew Cagney <cagney@kremvax.cygnus.com>
963 * Makefile.in (autoheader-common, autoheader-changelog,
964 autoheader-install): Perform autoheader in addition to autoconf.
966 Wed Apr 2 15:09:05 1997 Doug Evans <dje@canuck.cygnus.com>
968 * Makefile.in (autoconf-install): New target.
969 (autoconf-changelog): Try different way to obtain user name.
971 Wed Apr 2 14:25:52 1997 Andrew Cagney <cagney@kremvax.cygnus.com>
973 * Makefile.in (autoconf-changelog): New target, update
974 ChangeLog for all subdirectories - normally used after
975 autoconf-common target.
977 Wed Mar 19 14:26:21 1997 Andrew Cagney <cagney@kremvax.cygnus.com>
979 * configure.in (extra_subdirs): Include testsuite for d30v.
980 * configure: Regenerate.
982 * Makefile.in (RUNTEST, RUNTESTFLAGS): Borrow test rules from
984 (check): New rules - drive the testsuite.
986 Mon Mar 3 13:01:00 1997 Jeffrey A Law (law@cygnus.com)
988 * configure.in: Add mn10200 configure lines accidentally
990 * configure: Regenerated.
992 Wed Feb 19 10:34:20 1997 Andrew Cagney <cagney@critters.cygnus.com>
994 * configure.in (extra_subdirs): Generalize common sub directory
996 (extra_subdirs): For d30v add igen to the list to be built.
998 Sun Feb 16 16:37:47 1997 Andrew Cagney <cagney@critters.cygnus.com>
1000 * configure.in (d30v): New target.
1001 * configure: Regenerated.
1003 Wed Feb 19 23:17:13 1997 Jeffrey A Law (law@cygnus.com)
1005 * configure.in: Don't require GCC to build the mn10200
1007 * configure: Rebuilt.
1009 Wed Feb 5 13:28:13 1997 Doug Evans <dje@canuck.cygnus.com>
1011 * configure.in: Don't configure any subdirs if no simulator
1012 is being built. Don't use erc32 for sparc64.
1013 * configure: Regenerated.
1015 Tue Feb 4 13:19:39 1997 Doug Evans <dje@canuck.cygnus.com>
1017 * Makefile.in (autoconf-common): New target.
1018 * configure.in: Do configure common.
1019 * configure: Regenerated.
1021 Thu Jan 23 13:59:52 1997 Stu Grossman (grossman@critters.cygnus.com)
1023 * configure configure.in: Don't configure common anymore. Files
1024 from common are now built in the individual simualtor directories.
1025 This fixes problems with the WinGDB build procedure.
1027 Mon Jan 13 13:16:42 1997 Jeffrey A Law (law@cygnus.com)
1029 * configure: Enable the mn10200 simulator.
1031 Wed Nov 20 01:00:36 1996 Doug Evans <dje@canuck.cygnus.com>
1033 * configure.in (configdirs): Add common.
1034 * configure: Regenerated.
1036 Fri Nov 1 08:03:30 1996 Michael Meissner <meissner@tiktok.cygnus.com>
1038 * configure.in (powerpc*-*-linux*): Treat like the other powerpc
1039 system V based targets.
1040 * configure: Regenerate.
1042 Thu Oct 17 12:50:08 1996 Doug Evans <dje@canuck.cygnus.com>
1044 * configure.in (--enable-sim-powerpc): Delete.
1045 (--enable-sim): Add.
1046 * configure: Regenerated.
1048 Fri Oct 11 21:13:43 1996 Jeffrey A Law (law@cygnus.com)
1050 * configure.in: Only build the V850 simulator if
1052 * configure: Rebuild.
1054 Sun Sep 8 17:22:50 1996 Ian Lance Taylor <ian@cygnus.com>
1056 * configure.in: Do build erc32 for DOS and Windows hosts.
1057 * configure: Rebuild.
1059 Wed Sep 4 18:11:27 1996 Stu Grossman (grossman@critters.cygnus.com)
1061 * Makefile.in erc32/Makefile.in: Don't set srcroot. This should
1062 be inherited from the parent. Remove INSTALL_XFORM and
1063 INSTALL_XFORM1. Make INSTALL be set from configure.
1065 Wed Sep 4 15:49:16 1996 Ian Lance Taylor <ian@cygnus.com>
1067 * configure.in: Only build the MIPS simulator if we are using
1069 * configure: Rebuild.
1071 Wed Aug 28 19:05:23 1996 Jeffrey A Law (law@cygnus.com)
1073 * configure.in (v850-*-*): Added V850 simulator.
1075 Thu Aug 1 17:08:41 1996 Martin M. Hunt <hunt@pizza.cygnus.com>
1077 * configure.in (d10v-*-*): Added D10V simulator.
1079 Wed Jun 26 12:33:57 1996 Jason Molenda (crash@godzilla.cygnus.co.jp)
1081 * Makefile.in (bindir, libdir, datadir, mandir, infodir, includedir,
1082 INSTALL_PROGRAM, INSTALL_DATA): Use autoconf-set values.
1084 * configure.in (AC_PREREQ): autoconf 2.5 or higher.
1085 (AC_PROG_INSTALL): Added.
1086 * configure: Rebuilt.
1088 Mon Jun 24 14:18:26 1996 Ian Lance Taylor <ian@cygnus.com>
1090 * configure.in: Only configure erc32 if using gcc.
1091 * configure: Rebuild.
1093 Tue Jun 4 09:24:21 1996 Michael Meissner <meissner@tiktok.cygnus.com>
1095 * configure.in (sim_target): Build PowerPC simulator for powerpc
1096 System V.4, Solaris, and Elf targets.
1097 * configure: Regenerate with autoconf 2.10.
1099 Wed May 22 12:10:49 1996 Rob Savoye <rob@chinadoll>
1101 * configure.in: Only built erc32 simulator on Unix hosts as it
1103 * configure: Regenerated with autoconf 2.8.
1105 Sun May 19 20:20:40 1996 Rob Savoye <rob@chinadoll.cygnus.com>
1107 * erc32: Sparc simulator from the ESA.
1109 Sun Apr 7 21:00:09 1996 Fred Fish <fnf@cygnus.com>
1111 From: Miles Bader <miles@gnu.ai.mit.edu>
1112 * configure.in: Use AC_CHECK_TOOL to find AR & RANLIB.
1113 * configure: Regenerate using autoconf.
1115 Thu Feb 22 11:31:50 1996 Michael Meissner <meissner@tiktok.cygnus.com>
1117 * Makefile.in (install): Fix typo.
1119 Wed Feb 21 11:59:57 1996 Ian Lance Taylor <ian@cygnus.com>
1121 * configure: Regenerate with autoconf 2.7.
1123 * Makefile.in (all): Simplify.
1124 (clean, mostlyclean): SUBDIRS may contain whitespace; fix the loop
1125 as in the all target.
1126 (distclean, maintainer-clean, realclean): Likewise.
1127 (install): Likewise.
1129 Thu Feb 15 18:37:00 1996 Fred Fish <fnf@cygnus.com>
1131 * Makefile.in (all): Remove extra '\' char from shell script.
1133 Wed Feb 14 16:43:59 1996 Mike Meissner <meissner@tiktok.cygnus.com>
1135 * Makefile.in (all): Avoid a for loop with zero elements, even if
1136 the loop will not be executed because of an if statement.
1138 Wed Jan 31 21:48:34 1996 Fred Fish <fnf@cygnus.com>
1140 * Makefile.in (install): Add missing semicolon in "fi \".
1142 Thu Nov 9 16:10:56 1995 Michael Meissner <meissner@tiktok.cygnus.com>
1144 * Makefile.in (AR, CC, CFLAGS, CC_FOR_BUILD, RANLIB): Pick up
1145 defaults from configure.
1147 * configure.in: Pick up AR, CC, CFLAGS, CC_FOR_BUILD, RANLIB using
1149 (powerpc*-*-eabi*): Build simulator for all powerpc eabi targets
1150 if either --enable-sim-powerpc is used, or the host compiler is
1153 Wed Nov 8 15:46:49 1995 James G. Smith <jsmith@pasanda.cygnus.co.uk>
1155 * configure.in (mips*-*-*): Added "mips" simulator target.
1156 * configure: Re-generated.
1158 Tue Oct 10 11:08:20 1995 Fred Fish <fnf@cygnus.com>
1160 * Makefile.in (BISON): Remove macro.
1161 (FLAGS_TO_PASS): Remove BISON.
1163 Sun Oct 8 04:26:27 1995 Peter Schauer (pes@regent.e-technik.tu-muenchen.de)
1165 * configure.in: Explicitly `exit 0' for broken shells.
1166 * configure: Rebuilt.
1168 Fri Oct 6 12:03:27 1995 Jim Wilson <wilson@chestnut.cygnus.com>
1170 * common/run.c (main): Initialize the callbacks.
1172 Wed Sep 20 13:34:50 1995 Ian Lance Taylor <ian@cygnus.com>
1174 * Makefile.in (maintainer-clean): New synonym for realclean.
1176 Fri Aug 25 11:53:43 1995 Michael Meissner <meissner@tiktok.cygnus.com>
1178 * configure.in (powerpc*-*-eabisim*): Only build the simulator if
1179 the target is powerpc*-*-eabisim*, since it requires GCC to build.
1181 Mon Aug 21 17:53:48 1995 Michael Meissner <meissner@tiktok.cygnus.com>
1183 * configure.in (powerpc{,le}-*-*): Add psim from Andrew Cagney
1184 <cagney@highland.com.au>.
1185 * configure: Regnerate from configure.in.
1187 Thu Aug 3 10:45:37 1995 Fred Fish <fnf@cygnus.com>
1189 * Update all FSF addresses except those in COPYING* files.
1191 Thu Jul 20 15:17:29 1995 Fred Fish <fnf@cygnus.com>
1193 * Makefile.in (CC_FOR_BUILD): Define default and arrange to pass
1194 submakes either default or passed in value.
1196 Wed Jul 5 14:32:54 1995 J.T. Conklin <jtc@rtl.cygnus.com>
1198 * Makefile.in (all, clean, distclean, mostlyclean, realclean,
1199 install): Changed targets so that they descend all
1200 subdirectories in $(SUBDIRS).
1201 (*-all, *-clean, *-install): Removed targets.
1203 * configure.in: Don't bother with target makefile fragments, they
1204 are no longer needed.
1205 * configure: regenerated.
1207 * Makefile.in, configure.in: converted to autoconf.
1208 * configure: New file, generated with autconf 2.4.
1210 Wed May 24 14:48:46 1995 Steve Chamberlain <sac@slash.cygnus.com>
1212 * Makefile.in: Support ARM.
1213 * configure.in: Ditto.
1215 Sun Jan 15 16:53:47 1995 Steve Chamberlain <sac@splat>
1217 * Makefile.in: Support W65.
1218 * configure.in: Ditto.
1220 Sun Mar 13 09:27:50 1994 Jim Kingdon (kingdon@lioth.cygnus.com)
1222 * Makefile.in: Add TAGS target.
1224 Mon Sep 13 12:47:15 1993 K. Richard Pixley (rich@sendai.cygnus.com)
1226 * Makefile.in (all-z8k, install-z8k, clean-z8k, all-h8300,
1227 install-h8300, clean-h8300, all-h8500, install-h8500,
1228 clean-h8500, all-sh, install-sh, clean-sh): do not echo
1231 Wed Jun 30 14:12:05 1993 david d `zoo' zuhn (zoo at poseidon.cygnus.com)
1233 * Makefile.in: remove endian.h trace from h8500
1235 Sun Jun 13 13:08:58 1993 Jim Kingdon (kingdon@cygnus.com)
1237 * Makefile.in: Add distclean, realclean, and mostlyclean targets.
1239 Fri May 21 11:21:16 1993 david d `zoo' zuhn (zoo at cirdan.cygnus.com)
1241 * Makefile.in: make all of the all-* target (except all-nothing)
1242 depend on endian.h, so that if we're not building a simulator, we
1245 Fri May 21 10:55:06 1993 Ian Lance Taylor (ian@cygnus.com)
1247 * Makefile.in (check, installcheck): Added dummy targets.
1249 Mon May 3 21:39:43 1993 Fred Fish (fnf@cygnus.com)
1251 * Makefile.in (endian): Find endian.c in $(srcdir), and also
1252 explicitly make it, since some makes apparently don't work with
1253 VPATH and .c to executable rules (SunOS make for example).
1255 Mon May 3 08:29:01 1993 Steve Chamberlain (sac@thepub.cygnus.com)
1257 * Makefile.in (endian): Add explicit rule for broken makes.
1259 Mon Mar 15 15:47:53 1993 Ian Lance Taylor (ian@cygnus.com)
1261 * Makefile.in (info, install-info): New targets.
1262 (DO_INSTALL): Renamed from INSTALL, which is overridden by the top
1265 Wed Feb 10 20:12:27 1993 K. Richard Pixley (rich@ok.cygnus.com)
1267 * Makefile.in (endian.h): build endian.h via a temporary file so
1268 that we don't leave an incomplete file lying around on
1270 (clean): remove endian, e.h, and endian.h.
1272 Mon Feb 8 11:46:06 1993 Steve Chamberlain (sac@thepub.cygnus.com)
1274 * Makefile.in, configure.in: if target isn't supported, build a