sound/pci/echoaudio/echoaudio_dsp.c

   1 /****************************************************************************
   2
   3    Copyright Echo Digital Audio Corporation (c) 1998 - 2004
   4    All rights reserved
   5    www.echoaudio.com
   6
   7    This file is part of Echo Digital Audio's generic driver library.
   8
   9    Echo Digital Audio's generic driver library is free software;
  10    you can redistribute it and/or modify it under the terms of
  11    the GNU General Public License as published by the Free Software
  12    Foundation.
  13
  14    This program is distributed in the hope that it will be useful,
  15    but WITHOUT ANY WARRANTY; without even the implied warranty of
  16    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  17    GNU General Public License for more details.
  18
  19    You should have received a copy of the GNU General Public License
  20    along with this program; if not, write to the Free Software
  21    Foundation, Inc., 59 Temple Place - Suite 330, Boston,
  22    MA  02111-1307, USA.
  23
  24    *************************************************************************
  25
  26  Translation from C++ and adaptation for use in ALSA-Driver
  27  were made by Giuliano Pochini <pochini@shiny.it>
  28
  29 ****************************************************************************/
  30
  31 #if PAGE_SIZE < 4096
  32 #error PAGE_SIZE is < 4k
  33 #endif
  34
  35 static int restore_dsp_rettings(struct echoaudio *chip);
  36
  37
  38 /* Some vector commands involve the DSP reading or writing data to and from the
  39 comm page; if you send one of these commands to the DSP, it will complete the
  40 command and then write a non-zero value to the Handshake field in the
  41 comm page.  This function waits for the handshake to show up. */
  42 static int wait_handshake(struct echoaudio *chip)
  43 {
  44         int i;
  45
  46         /* Wait up to 20ms for the handshake from the DSP */
  47         for (i = 0; i < HANDSHAKE_TIMEOUT; i++) {
  48                 /* Look for the handshake value */
  49                 barrier();
  50                 if (chip->comm_page->handshake) {
  51                         return 0;
  52                 }
  53                 udelay(1);
  54         }
  55
  56         dev_err(chip->card->dev, "wait_handshake(): Timeout waiting for DSP\n");
  57         return -EBUSY;
  58 }
  59
  60
  61
  62 /* Much of the interaction between the DSP and the driver is done via vector
  63 commands; send_vector writes a vector command to the DSP.  Typically, this
  64 causes the DSP to read or write fields in the comm page.
  65 PCI posting is not required thanks to the handshake logic. */
  66 static int send_vector(struct echoaudio *chip, u32 command)
  67 {
  68         int i;
  69
  70         wmb();  /* Flush all pending writes before sending the command */
  71
  72         /* Wait up to 100ms for the "vector busy" bit to be off */
  73         for (i = 0; i < VECTOR_BUSY_TIMEOUT; i++) {
  74                 if (!(get_dsp_register(chip, CHI32_VECTOR_REG) &
  75                       CHI32_VECTOR_BUSY)) {
  76                         set_dsp_register(chip, CHI32_VECTOR_REG, command);
  77                         /*if (i)  DE_ACT(("send_vector time: %d\n", i));*/
  78                         return 0;
  79                 }
  80                 udelay(1);
  81         }
  82
  83         dev_err(chip->card->dev, "timeout on send_vector\n");
  84         return -EBUSY;
  85 }
  86
  87
  88
  89 /* write_dsp writes a 32-bit value to the DSP; this is used almost
  90 exclusively for loading the DSP. */
  91 static int write_dsp(struct echoaudio *chip, u32 data)
  92 {
  93         u32 status, i;
  94
  95         for (i = 0; i < 10000000; i++) {        /* timeout = 10s */
  96                 status = get_dsp_register(chip, CHI32_STATUS_REG);
  97                 if ((status & CHI32_STATUS_HOST_WRITE_EMPTY) != 0) {
  98                         set_dsp_register(chip, CHI32_DATA_REG, data);
  99                         wmb();                  /* write it immediately */
 100                         return 0;
 101                 }
 102                 udelay(1);
 103                 cond_resched();
 104         }
 105
 106         chip->bad_board = true;         /* Set true until DSP re-loaded */
 107         dev_dbg(chip->card->dev, "write_dsp: Set bad_board to true\n");
 108         return -EIO;
 109 }
 110
 111
 112
 113 /* read_dsp reads a 32-bit value from the DSP; this is used almost
 114 exclusively for loading the DSP and checking the status of the ASIC. */
 115 static int read_dsp(struct echoaudio *chip, u32 *data)
 116 {
 117         u32 status, i;
 118
 119         for (i = 0; i < READ_DSP_TIMEOUT; i++) {
 120                 status = get_dsp_register(chip, CHI32_STATUS_REG);
 121                 if ((status & CHI32_STATUS_HOST_READ_FULL) != 0) {
 122                         *data = get_dsp_register(chip, CHI32_DATA_REG);
 123                         return 0;
 124                 }
 125                 udelay(1);
 126                 cond_resched();
 127         }
 128
 129         chip->bad_board = true;         /* Set true until DSP re-loaded */
 130         dev_err(chip->card->dev, "read_dsp: Set bad_board to true\n");
 131         return -EIO;
 132 }
 133
 134
 135
 136 /****************************************************************************
 137         Firmware loading functions
 138  ****************************************************************************/
 139
 140 /* This function is used to read back the serial number from the DSP;
 141 this is triggered by the SET_COMMPAGE_ADDR command.
 142 Only some early Echogals products have serial numbers in the ROM;
 143 the serial number is not used, but you still need to do this as
 144 part of the DSP load process. */
 145 static int read_sn(struct echoaudio *chip)
 146 {
 147         int i;
 148         u32 sn[6];
 149
 150         for (i = 0; i < 5; i++) {
 151                 if (read_dsp(chip, &sn[i])) {
 152                         dev_err(chip->card->dev,
 153                                 "Failed to read serial number\n");
 154                         return -EIO;
 155                 }
 156         }
 157         dev_dbg(chip->card->dev,
 158                 "Read serial number %08x %08x %08x %08x %08x\n",
 159                  sn[0], sn[1], sn[2], sn[3], sn[4]);
 160         return 0;
 161 }
 162
 163
 164
 165 #ifndef ECHOCARD_HAS_ASIC
 166 /* This card has no ASIC, just return ok */
 167 static inline int check_asic_status(struct echoaudio *chip)
 168 {
 169         chip->asic_loaded = true;
 170         return 0;
 171 }
 172
 173 #endif /* !ECHOCARD_HAS_ASIC */
 174
 175
 176
 177 #ifdef ECHOCARD_HAS_ASIC
 178
 179 /* Load ASIC code - done after the DSP is loaded */
 180 static int load_asic_generic(struct echoaudio *chip, u32 cmd, short asic)
 181 {
 182         const struct firmware *fw;
 183         int err;
 184         u32 i, size;
 185         u8 *code;
 186
 187         err = get_firmware(&fw, chip, asic);
 188         if (err < 0) {
 189                 dev_warn(chip->card->dev, "Firmware not found !\n");
 190                 return err;
 191         }
 192
 193         code = (u8 *)fw->data;
 194         size = fw->size;
 195
 196         /* Send the "Here comes the ASIC" command */
 197         if (write_dsp(chip, cmd) < 0)
 198                 goto la_error;
 199
 200         /* Write length of ASIC file in bytes */
 201         if (write_dsp(chip, size) < 0)
 202                 goto la_error;
 203
 204         for (i = 0; i < size; i++) {
 205                 if (write_dsp(chip, code[i]) < 0)
 206                         goto la_error;
 207         }
 208
 209         free_firmware(fw, chip);
 210         return 0;
 211
 212 la_error:
 213         dev_err(chip->card->dev, "failed on write_dsp\n");
 214         free_firmware(fw, chip);
 215         return -EIO;
 216 }
 217
 218 #endif /* ECHOCARD_HAS_ASIC */
 219
 220
 221
 222 #ifdef DSP_56361
 223
 224 /* Install the resident loader for 56361 DSPs;  The resident loader is on
 225 the EPROM on the board for 56301 DSP. The resident loader is a tiny little
 226 program that is used to load the real DSP code. */
 227 static int install_resident_loader(struct echoaudio *chip)
 228 {
 229         u32 address;
 230         int index, words, i;
 231         u16 *code;
 232         u32 status;
 233         const struct firmware *fw;
 234
 235         /* 56361 cards only!  This check is required by the old 56301-based
 236         Mona and Gina24 */
 237         if (chip->device_id != DEVICE_ID_56361)
 238                 return 0;
 239
 240         /* Look to see if the resident loader is present.  If the resident
 241         loader is already installed, host flag 5 will be on. */
 242         status = get_dsp_register(chip, CHI32_STATUS_REG);
 243         if (status & CHI32_STATUS_REG_HF5) {
 244                 dev_dbg(chip->card->dev,
 245                         "Resident loader already installed; status is 0x%x\n",
 246                          status);
 247                 return 0;
 248         }
 249
 250         i = get_firmware(&fw, chip, FW_361_LOADER);
 251         if (i < 0) {
 252                 dev_warn(chip->card->dev, "Firmware not found !\n");
 253                 return i;
 254         }
 255
 256         /* The DSP code is an array of 16 bit words.  The array is divided up
 257         into sections.  The first word of each section is the size in words,
 258         followed by the section type.
 259         Since DSP addresses and data are 24 bits wide, they each take up two
 260         16 bit words in the array.
 261         This is a lot like the other loader loop, but it's not a loop, you
 262         don't write the memory type, and you don't write a zero at the end. */
 263
 264         /* Set DSP format bits for 24 bit mode */
 265         set_dsp_register(chip, CHI32_CONTROL_REG,
 266                          get_dsp_register(chip, CHI32_CONTROL_REG) | 0x900);
 267
 268         code = (u16 *)fw->data;
 269
 270         /* Skip the header section; the first word in the array is the size
 271         of the first section, so the first real section of code is pointed
 272         to by Code[0]. */
 273         index = code[0];
 274
 275         /* Skip the section size, LRS block type, and DSP memory type */
 276         index += 3;
 277
 278         /* Get the number of DSP words to write */
 279         words = code[index++];
 280
 281         /* Get the DSP address for this block; 24 bits, so build from two words */
 282         address = ((u32)code[index] << 16) + code[index + 1];
 283         index += 2;
 284
 285         /* Write the count to the DSP */
 286         if (write_dsp(chip, words)) {
 287                 dev_err(chip->card->dev,
 288                         "install_resident_loader: Failed to write word count!\n");
 289                 goto irl_error;
 290         }
 291         /* Write the DSP address */
 292         if (write_dsp(chip, address)) {
 293                 dev_err(chip->card->dev,
 294                         "install_resident_loader: Failed to write DSP address!\n");
 295                 goto irl_error;
 296         }
 297         /* Write out this block of code to the DSP */
 298         for (i = 0; i < words; i++) {
 299                 u32 data;
 300
 301                 data = ((u32)code[index] << 16) + code[index + 1];
 302                 if (write_dsp(chip, data)) {
 303                         dev_err(chip->card->dev,
 304                                 "install_resident_loader: Failed to write DSP code\n");
 305                         goto irl_error;
 306                 }
 307                 index += 2;
 308         }
 309
 310         /* Wait for flag 5 to come up */
 311         for (i = 0; i < 200; i++) {     /* Timeout is 50us * 200 = 10ms */
 312                 udelay(50);
 313                 status = get_dsp_register(chip, CHI32_STATUS_REG);
 314                 if (status & CHI32_STATUS_REG_HF5)
 315                         break;
 316         }
 317
 318         if (i == 200) {
 319                 dev_err(chip->card->dev, "Resident loader failed to set HF5\n");
 320                 goto irl_error;
 321         }
 322
 323         dev_dbg(chip->card->dev, "Resident loader successfully installed\n");
 324         free_firmware(fw, chip);
 325         return 0;
 326
 327 irl_error:
 328         free_firmware(fw, chip);
 329         return -EIO;
 330 }
 331
 332 #endif /* DSP_56361 */
 333
 334
 335 static int load_dsp(struct echoaudio *chip, u16 *code)
 336 {
 337         u32 address, data;
 338         int index, words, i;
 339
 340         if (chip->dsp_code == code) {
 341                 dev_warn(chip->card->dev, "DSP is already loaded!\n");
 342                 return 0;
 343         }
 344         chip->bad_board = true;         /* Set true until DSP loaded */
 345         chip->dsp_code = NULL;          /* Current DSP code not loaded */
 346         chip->asic_loaded = false;      /* Loading the DSP code will reset the ASIC */
 347
 348         dev_dbg(chip->card->dev, "load_dsp: Set bad_board to true\n");
 349
 350         /* If this board requires a resident loader, install it. */
 351 #ifdef DSP_56361
 352         if ((i = install_resident_loader(chip)) < 0)
 353                 return i;
 354 #endif
 355
 356         /* Send software reset command */
 357         if (send_vector(chip, DSP_VC_RESET) < 0) {
 358                 dev_err(chip->card->dev,
 359                         "LoadDsp: send_vector DSP_VC_RESET failed, Critical Failure\n");
 360                 return -EIO;
 361         }
 362         /* Delay 10us */
 363         udelay(10);
 364
 365         /* Wait 10ms for HF3 to indicate that software reset is complete */
 366         for (i = 0; i < 1000; i++) {    /* Timeout is 10us * 1000 = 10ms */
 367                 if (get_dsp_register(chip, CHI32_STATUS_REG) &
 368                     CHI32_STATUS_REG_HF3)
 369                         break;
 370                 udelay(10);
 371         }
 372
 373         if (i == 1000) {
 374                 dev_err(chip->card->dev,
 375                         "load_dsp: Timeout waiting for CHI32_STATUS_REG_HF3\n");
 376                 return -EIO;
 377         }
 378
 379         /* Set DSP format bits for 24 bit mode now that soft reset is done */
 380         set_dsp_register(chip, CHI32_CONTROL_REG,
 381                          get_dsp_register(chip, CHI32_CONTROL_REG) | 0x900);
 382
 383         /* Main loader loop */
 384
 385         index = code[0];
 386         for (;;) {
 387                 int block_type, mem_type;
 388
 389                 /* Total Block Size */
 390                 index++;
 391
 392                 /* Block Type */
 393                 block_type = code[index];
 394                 if (block_type == 4)    /* We're finished */
 395                         break;
 396
 397                 index++;
 398
 399                 /* Memory Type  P=0,X=1,Y=2 */
 400                 mem_type = code[index++];
 401
 402                 /* Block Code Size */
 403                 words = code[index++];
 404                 if (words == 0)         /* We're finished */
 405                         break;
 406
 407                 /* Start Address */
 408                 address = ((u32)code[index] << 16) + code[index + 1];
 409                 index += 2;
 410
 411                 if (write_dsp(chip, words) < 0) {
 412                         dev_err(chip->card->dev,
 413                                 "load_dsp: failed to write number of DSP words\n");
 414                         return -EIO;
 415                 }
 416                 if (write_dsp(chip, address) < 0) {
 417                         dev_err(chip->card->dev,
 418                                 "load_dsp: failed to write DSP address\n");
 419                         return -EIO;
 420                 }
 421                 if (write_dsp(chip, mem_type) < 0) {
 422                         dev_err(chip->card->dev,
 423                                 "load_dsp: failed to write DSP memory type\n");
 424                         return -EIO;
 425                 }
 426                 /* Code */
 427                 for (i = 0; i < words; i++, index+=2) {
 428                         data = ((u32)code[index] << 16) + code[index + 1];
 429                         if (write_dsp(chip, data) < 0) {
 430                                 dev_err(chip->card->dev,
 431                                         "load_dsp: failed to write DSP data\n");
 432                                 return -EIO;
 433                         }
 434                 }
 435         }
 436
 437         if (write_dsp(chip, 0) < 0) {   /* We're done!!! */
 438                 dev_err(chip->card->dev,
 439                         "load_dsp: Failed to write final zero\n");
 440                 return -EIO;
 441         }
 442         udelay(10);
 443
 444         for (i = 0; i < 5000; i++) {    /* Timeout is 100us * 5000 = 500ms */
 445                 /* Wait for flag 4 - indicates that the DSP loaded OK */
 446                 if (get_dsp_register(chip, CHI32_STATUS_REG) &
 447                     CHI32_STATUS_REG_HF4) {
 448                         set_dsp_register(chip, CHI32_CONTROL_REG,
 449                                          get_dsp_register(chip, CHI32_CONTROL_REG) & ~0x1b00);
 450
 451                         if (write_dsp(chip, DSP_FNC_SET_COMMPAGE_ADDR) < 0) {
 452                                 dev_err(chip->card->dev,
 453                                         "load_dsp: Failed to write DSP_FNC_SET_COMMPAGE_ADDR\n");
 454                                 return -EIO;
 455                         }
 456
 457                         if (write_dsp(chip, chip->comm_page_phys) < 0) {
 458                                 dev_err(chip->card->dev,
 459                                         "load_dsp: Failed to write comm page address\n");
 460                                 return -EIO;
 461                         }
 462
 463                         /* Get the serial number via slave mode.
 464                         This is triggered by the SET_COMMPAGE_ADDR command.
 465                         We don't actually use the serial number but we have to
 466                         get it as part of the DSP init voodoo. */
 467                         if (read_sn(chip) < 0) {
 468                                 dev_err(chip->card->dev,
 469                                         "load_dsp: Failed to read serial number\n");
 470                                 return -EIO;
 471                         }
 472
 473                         chip->dsp_code = code;          /* Show which DSP code loaded */
 474                         chip->bad_board = false;        /* DSP OK */
 475                         return 0;
 476                 }
 477                 udelay(100);
 478         }
 479
 480         dev_err(chip->card->dev,
 481                 "load_dsp: DSP load timed out waiting for HF4\n");
 482         return -EIO;
 483 }
 484
 485
 486
 487 /* load_firmware takes care of loading the DSP and any ASIC code. */
 488 static int load_firmware(struct echoaudio *chip)
 489 {
 490         const struct firmware *fw;
 491         int box_type, err;
 492
 493         if (snd_BUG_ON(!chip->comm_page))
 494                 return -EPERM;
 495
 496         /* See if the ASIC is present and working - only if the DSP is already loaded */
 497         if (chip->dsp_code) {
 498                 if ((box_type = check_asic_status(chip)) >= 0)
 499                         return box_type;
 500                 /* ASIC check failed; force the DSP to reload */
 501                 chip->dsp_code = NULL;
 502         }
 503
 504         err = get_firmware(&fw, chip, chip->dsp_code_to_load);
 505         if (err < 0)
 506                 return err;
 507         err = load_dsp(chip, (u16 *)fw->data);
 508         free_firmware(fw, chip);
 509         if (err < 0)
 510                 return err;
 511
 512         if ((box_type = load_asic(chip)) < 0)
 513                 return box_type;        /* error */
 514
 515         return box_type;
 516 }
 517
 518
 519
 520 /****************************************************************************
 521         Mixer functions
 522  ****************************************************************************/
 523
 524 #if defined(ECHOCARD_HAS_INPUT_NOMINAL_LEVEL) || \
 525         defined(ECHOCARD_HAS_OUTPUT_NOMINAL_LEVEL)
 526
 527 /* Set the nominal level for an input or output bus (true = -10dBV, false = +4dBu) */
 528 static int set_nominal_level(struct echoaudio *chip, u16 index, char consumer)
 529 {
 530         if (snd_BUG_ON(index >= num_busses_out(chip) + num_busses_in(chip)))
 531                 return -EINVAL;
 532
 533         /* Wait for the handshake (OK even if ASIC is not loaded) */
 534         if (wait_handshake(chip))
 535                 return -EIO;
 536
 537         chip->nominal_level[index] = consumer;
 538
 539         if (consumer)
 540                 chip->comm_page->nominal_level_mask |= cpu_to_le32(1 << index);
 541         else
 542                 chip->comm_page->nominal_level_mask &= ~cpu_to_le32(1 << index);
 543
 544         return 0;
 545 }
 546
 547 #endif /* ECHOCARD_HAS_*_NOMINAL_LEVEL */
 548
 549
 550
 551 /* Set the gain for a single physical output channel (dB). */
 552 static int set_output_gain(struct echoaudio *chip, u16 channel, s8 gain)
 553 {
 554         if (snd_BUG_ON(channel >= num_busses_out(chip)))
 555                 return -EINVAL;
 556
 557         if (wait_handshake(chip))
 558                 return -EIO;
 559
 560         /* Save the new value */
 561         chip->output_gain[channel] = gain;
 562         chip->comm_page->line_out_level[channel] = gain;
 563         return 0;
 564 }
 565
 566
 567
 568 #ifdef ECHOCARD_HAS_MONITOR
 569 /* Set the monitor level from an input bus to an output bus. */
 570 static int set_monitor_gain(struct echoaudio *chip, u16 output, u16 input,
 571                             s8 gain)
 572 {
 573         if (snd_BUG_ON(output >= num_busses_out(chip) ||
 574                     input >= num_busses_in(chip)))
 575                 return -EINVAL;
 576
 577         if (wait_handshake(chip))
 578                 return -EIO;
 579
 580         chip->monitor_gain[output][input] = gain;
 581         chip->comm_page->monitors[monitor_index(chip, output, input)] = gain;
 582         return 0;
 583 }
 584 #endif /* ECHOCARD_HAS_MONITOR */
 585
 586
 587 /* Tell the DSP to read and update output, nominal & monitor levels in comm page. */
 588 static int update_output_line_level(struct echoaudio *chip)
 589 {
 590         if (wait_handshake(chip))
 591                 return -EIO;
 592         clear_handshake(chip);
 593         return send_vector(chip, DSP_VC_UPDATE_OUTVOL);
 594 }
 595
 596
 597
 598 /* Tell the DSP to read and update input levels in comm page */
 599 static int update_input_line_level(struct echoaudio *chip)
 600 {
 601         if (wait_handshake(chip))
 602                 return -EIO;
 603         clear_handshake(chip);
 604         return send_vector(chip, DSP_VC_UPDATE_INGAIN);
 605 }
 606
 607
 608
 609 /* set_meters_on turns the meters on or off.  If meters are turned on, the DSP
 610 will write the meter and clock detect values to the comm page at about 30Hz */
 611 static void set_meters_on(struct echoaudio *chip, char on)
 612 {
 613         if (on && !chip->meters_enabled) {
 614                 send_vector(chip, DSP_VC_METERS_ON);
 615                 chip->meters_enabled = 1;
 616         } else if (!on && chip->meters_enabled) {
 617                 send_vector(chip, DSP_VC_METERS_OFF);
 618                 chip->meters_enabled = 0;
 619                 memset((s8 *)chip->comm_page->vu_meter, ECHOGAIN_MUTED,
 620                        DSP_MAXPIPES);
 621                 memset((s8 *)chip->comm_page->peak_meter, ECHOGAIN_MUTED,
 622                        DSP_MAXPIPES);
 623         }
 624 }
 625
 626
 627
 628 /* Fill out an the given array using the current values in the comm page.
 629 Meters are written in the comm page by the DSP in this order:
 630  Output busses
 631  Input busses
 632  Output pipes (vmixer cards only)
 633
 634 This function assumes there are no more than 16 in/out busses or pipes
 635 Meters is an array [3][16][2] of long. */
 636 static void get_audio_meters(struct echoaudio *chip, long *meters)
 637 {
 638         int i, m, n;
 639
 640         m = 0;
 641         n = 0;
 642         for (i = 0; i < num_busses_out(chip); i++, m++) {
 643                 meters[n++] = chip->comm_page->vu_meter[m];
 644                 meters[n++] = chip->comm_page->peak_meter[m];
 645         }
 646         for (; n < 32; n++)
 647                 meters[n] = 0;
 648
 649 #ifdef ECHOCARD_ECHO3G
 650         m = E3G_MAX_OUTPUTS;    /* Skip unused meters */
 651 #endif
 652
 653         for (i = 0; i < num_busses_in(chip); i++, m++) {
 654                 meters[n++] = chip->comm_page->vu_meter[m];
 655                 meters[n++] = chip->comm_page->peak_meter[m];
 656         }
 657         for (; n < 64; n++)
 658                 meters[n] = 0;
 659
 660 #ifdef ECHOCARD_HAS_VMIXER
 661         for (i = 0; i < num_pipes_out(chip); i++, m++) {
 662                 meters[n++] = chip->comm_page->vu_meter[m];
 663                 meters[n++] = chip->comm_page->peak_meter[m];
 664         }
 665 #endif
 666         for (; n < 96; n++)
 667                 meters[n] = 0;
 668 }
 669
 670
 671
 672 static int restore_dsp_rettings(struct echoaudio *chip)
 673 {
 674         int i, o, err;
 675
 676         if ((err = check_asic_status(chip)) < 0)
 677                 return err;
 678
 679         /* Gina20/Darla20 only. Should be harmless for other cards. */
 680         chip->comm_page->gd_clock_state = GD_CLOCK_UNDEF;
 681         chip->comm_page->gd_spdif_status = GD_SPDIF_STATUS_UNDEF;
 682         chip->comm_page->handshake = 0xffffffff;
 683
 684         /* Restore output busses */
 685         for (i = 0; i < num_busses_out(chip); i++) {
 686                 err = set_output_gain(chip, i, chip->output_gain[i]);
 687                 if (err < 0)
 688                         return err;
 689         }
 690
 691 #ifdef ECHOCARD_HAS_VMIXER
 692         for (i = 0; i < num_pipes_out(chip); i++)
 693                 for (o = 0; o < num_busses_out(chip); o++) {
 694                         err = set_vmixer_gain(chip, o, i,
 695                                                 chip->vmixer_gain[o][i]);
 696                         if (err < 0)
 697                                 return err;
 698                 }
 699         if (update_vmixer_level(chip) < 0)
 700                 return -EIO;
 701 #endif /* ECHOCARD_HAS_VMIXER */
 702
 703 #ifdef ECHOCARD_HAS_MONITOR
 704         for (o = 0; o < num_busses_out(chip); o++)
 705                 for (i = 0; i < num_busses_in(chip); i++) {
 706                         err = set_monitor_gain(chip, o, i,
 707                                                 chip->monitor_gain[o][i]);
 708                         if (err < 0)
 709                                 return err;
 710                 }
 711 #endif /* ECHOCARD_HAS_MONITOR */
 712
 713 #ifdef ECHOCARD_HAS_INPUT_GAIN
 714         for (i = 0; i < num_busses_in(chip); i++) {
 715                 err = set_input_gain(chip, i, chip->input_gain[i]);
 716                 if (err < 0)
 717                         return err;
 718         }
 719 #endif /* ECHOCARD_HAS_INPUT_GAIN */
 720
 721         err = update_output_line_level(chip);
 722         if (err < 0)
 723                 return err;
 724
 725         err = update_input_line_level(chip);
 726         if (err < 0)
 727                 return err;
 728
 729         err = set_sample_rate(chip, chip->sample_rate);
 730         if (err < 0)
 731                 return err;
 732
 733         if (chip->meters_enabled) {
 734                 err = send_vector(chip, DSP_VC_METERS_ON);
 735                 if (err < 0)
 736                         return err;
 737         }
 738
 739 #ifdef ECHOCARD_HAS_DIGITAL_MODE_SWITCH
 740         if (set_digital_mode(chip, chip->digital_mode) < 0)
 741                 return -EIO;
 742 #endif
 743
 744 #ifdef ECHOCARD_HAS_DIGITAL_IO
 745         if (set_professional_spdif(chip, chip->professional_spdif) < 0)
 746                 return -EIO;
 747 #endif
 748
 749 #ifdef ECHOCARD_HAS_PHANTOM_POWER
 750         if (set_phantom_power(chip, chip->phantom_power) < 0)
 751                 return -EIO;
 752 #endif
 753
 754 #ifdef ECHOCARD_HAS_EXTERNAL_CLOCK
 755         /* set_input_clock() also restores automute setting */
 756         if (set_input_clock(chip, chip->input_clock) < 0)
 757                 return -EIO;
 758 #endif
 759
 760 #ifdef ECHOCARD_HAS_OUTPUT_CLOCK_SWITCH
 761         if (set_output_clock(chip, chip->output_clock) < 0)
 762                 return -EIO;
 763 #endif
 764
 765         if (wait_handshake(chip) < 0)
 766                 return -EIO;
 767         clear_handshake(chip);
 768         if (send_vector(chip, DSP_VC_UPDATE_FLAGS) < 0)
 769                 return -EIO;
 770
 771         return 0;
 772 }
 773
 774
 775
 776 /****************************************************************************
 777         Transport functions
 778  ****************************************************************************/
 779
 780 /* set_audio_format() sets the format of the audio data in host memory for
 781 this pipe.  Note that _MS_ (mono-to-stereo) playback modes are not used by ALSA
 782 but they are here because they are just mono while capturing */
 783 static void set_audio_format(struct echoaudio *chip, u16 pipe_index,
 784                              const struct audioformat *format)
 785 {
 786         u16 dsp_format;
 787
 788         dsp_format = DSP_AUDIOFORM_SS_16LE;
 789
 790         /* Look for super-interleave (no big-endian and 8 bits) */
 791         if (format->interleave > 2) {
 792                 switch (format->bits_per_sample) {
 793                 case 16:
 794                         dsp_format = DSP_AUDIOFORM_SUPER_INTERLEAVE_16LE;
 795                         break;
 796                 case 24:
 797                         dsp_format = DSP_AUDIOFORM_SUPER_INTERLEAVE_24LE;
 798                         break;
 799                 case 32:
 800                         dsp_format = DSP_AUDIOFORM_SUPER_INTERLEAVE_32LE;
 801                         break;
 802                 }
 803                 dsp_format |= format->interleave;
 804         } else if (format->data_are_bigendian) {
 805                 /* For big-endian data, only 32 bit samples are supported */
 806                 switch (format->interleave) {
 807                 case 1:
 808                         dsp_format = DSP_AUDIOFORM_MM_32BE;
 809                         break;
 810 #ifdef ECHOCARD_HAS_STEREO_BIG_ENDIAN32
 811                 case 2:
 812                         dsp_format = DSP_AUDIOFORM_SS_32BE;
 813                         break;
 814 #endif
 815                 }
 816         } else if (format->interleave == 1 &&
 817                    format->bits_per_sample == 32 && !format->mono_to_stereo) {
 818                 /* 32 bit little-endian mono->mono case */
 819                 dsp_format = DSP_AUDIOFORM_MM_32LE;
 820         } else {
 821                 /* Handle the other little-endian formats */
 822                 switch (format->bits_per_sample) {
 823                 case 8:
 824                         if (format->interleave == 2)
 825                                 dsp_format = DSP_AUDIOFORM_SS_8;
 826                         else
 827                                 dsp_format = DSP_AUDIOFORM_MS_8;
 828                         break;
 829                 default:
 830                 case 16:
 831                         if (format->interleave == 2)
 832                                 dsp_format = DSP_AUDIOFORM_SS_16LE;
 833                         else
 834                                 dsp_format = DSP_AUDIOFORM_MS_16LE;
 835                         break;
 836                 case 24:
 837                         if (format->interleave == 2)
 838                                 dsp_format = DSP_AUDIOFORM_SS_24LE;
 839                         else
 840                                 dsp_format = DSP_AUDIOFORM_MS_24LE;
 841                         break;
 842                 case 32:
 843                         if (format->interleave == 2)
 844                                 dsp_format = DSP_AUDIOFORM_SS_32LE;
 845                         else
 846                                 dsp_format = DSP_AUDIOFORM_MS_32LE;
 847                         break;
 848                 }
 849         }
 850         dev_dbg(chip->card->dev,
 851                  "set_audio_format[%d] = %x\n", pipe_index, dsp_format);
 852         chip->comm_page->audio_format[pipe_index] = cpu_to_le16(dsp_format);
 853 }
 854
 855
 856
 857 /* start_transport starts transport for a set of pipes.
 858 The bits 1 in channel_mask specify what pipes to start. Only the bit of the
 859 first channel must be set, regardless its interleave.
 860 Same thing for pause_ and stop_ -trasport below. */
 861 static int start_transport(struct echoaudio *chip, u32 channel_mask,
 862                            u32 cyclic_mask)
 863 {
 864
 865         if (wait_handshake(chip))
 866                 return -EIO;
 867
 868         chip->comm_page->cmd_start |= cpu_to_le32(channel_mask);
 869
 870         if (chip->comm_page->cmd_start) {
 871                 clear_handshake(chip);
 872                 send_vector(chip, DSP_VC_START_TRANSFER);
 873                 if (wait_handshake(chip))
 874                         return -EIO;
 875                 /* Keep track of which pipes are transporting */
 876                 chip->active_mask |= channel_mask;
 877                 chip->comm_page->cmd_start = 0;
 878                 return 0;
 879         }
 880
 881         dev_err(chip->card->dev, "start_transport: No pipes to start!\n");
 882         return -EINVAL;
 883 }
 884
 885
 886
 887 static int pause_transport(struct echoaudio *chip, u32 channel_mask)
 888 {
 889
 890         if (wait_handshake(chip))
 891                 return -EIO;
 892
 893         chip->comm_page->cmd_stop |= cpu_to_le32(channel_mask);
 894         chip->comm_page->cmd_reset = 0;
 895         if (chip->comm_page->cmd_stop) {
 896                 clear_handshake(chip);
 897                 send_vector(chip, DSP_VC_STOP_TRANSFER);
 898                 if (wait_handshake(chip))
 899                         return -EIO;
 900                 /* Keep track of which pipes are transporting */
 901                 chip->active_mask &= ~channel_mask;
 902                 chip->comm_page->cmd_stop = 0;
 903                 chip->comm_page->cmd_reset = 0;
 904                 return 0;
 905         }
 906
 907         dev_warn(chip->card->dev, "pause_transport: No pipes to stop!\n");
 908         return 0;
 909 }
 910
 911
 912
 913 static int stop_transport(struct echoaudio *chip, u32 channel_mask)
 914 {
 915
 916         if (wait_handshake(chip))
 917                 return -EIO;
 918
 919         chip->comm_page->cmd_stop |= cpu_to_le32(channel_mask);
 920         chip->comm_page->cmd_reset |= cpu_to_le32(channel_mask);
 921         if (chip->comm_page->cmd_reset) {
 922                 clear_handshake(chip);
 923                 send_vector(chip, DSP_VC_STOP_TRANSFER);
 924                 if (wait_handshake(chip))
 925                         return -EIO;
 926                 /* Keep track of which pipes are transporting */
 927                 chip->active_mask &= ~channel_mask;
 928                 chip->comm_page->cmd_stop = 0;
 929                 chip->comm_page->cmd_reset = 0;
 930                 return 0;
 931         }
 932
 933         dev_warn(chip->card->dev, "stop_transport: No pipes to stop!\n");
 934         return 0;
 935 }
 936
 937
 938
 939 static inline int is_pipe_allocated(struct echoaudio *chip, u16 pipe_index)
 940 {
 941         return (chip->pipe_alloc_mask & (1 << pipe_index));
 942 }
 943
 944
 945
 946 /* Stops everything and turns off the DSP. All pipes should be already
 947 stopped and unallocated. */
 948 static int rest_in_peace(struct echoaudio *chip)
 949 {
 950
 951         /* Stops all active pipes (just to be sure) */
 952         stop_transport(chip, chip->active_mask);
 953
 954         set_meters_on(chip, false);
 955
 956 #ifdef ECHOCARD_HAS_MIDI
 957         enable_midi_input(chip, false);
 958 #endif
 959
 960         /* Go to sleep */
 961         if (chip->dsp_code) {
 962                 /* Make load_firmware do a complete reload */
 963                 chip->dsp_code = NULL;
 964                 /* Put the DSP to sleep */
 965                 return send_vector(chip, DSP_VC_GO_COMATOSE);
 966         }
 967         return 0;
 968 }
 969
 970
 971
 972 /* Fills the comm page with default values */
 973 static int init_dsp_comm_page(struct echoaudio *chip)
 974 {
 975         /* Check if the compiler added extra padding inside the structure */
 976         if (offsetof(struct comm_page, midi_output) != 0xbe0) {
 977                 dev_err(chip->card->dev,
 978                         "init_dsp_comm_page() - Invalid struct comm_page structure\n");
 979                 return -EPERM;
 980         }
 981
 982         /* Init all the basic stuff */
 983         chip->card_name = ECHOCARD_NAME;
 984         chip->bad_board = true; /* Set true until DSP loaded */
 985         chip->dsp_code = NULL;  /* Current DSP code not loaded */
 986         chip->asic_loaded = false;
 987         memset(chip->comm_page, 0, sizeof(struct comm_page));
 988
 989         /* Init the comm page */
 990         chip->comm_page->comm_size =
 991                 cpu_to_le32(sizeof(struct comm_page));
 992         chip->comm_page->handshake = 0xffffffff;
 993         chip->comm_page->midi_out_free_count =
 994                 cpu_to_le32(DSP_MIDI_OUT_FIFO_SIZE);
 995         chip->comm_page->sample_rate = cpu_to_le32(44100);
 996
 997         /* Set line levels so we don't blast any inputs on startup */
 998         memset(chip->comm_page->monitors, ECHOGAIN_MUTED, MONITOR_ARRAY_SIZE);
 999         memset(chip->comm_page->vmixer, ECHOGAIN_MUTED, VMIXER_ARRAY_SIZE);
1000
1001         return 0;
1002 }
1003
1004
1005
1006 /* This function initializes the chip structure with default values, ie. all
1007  * muted and internal clock source. Then it copies the settings to the DSP.
1008  * This MUST be called after the DSP is up and running !
1009  */
1010 static int init_line_levels(struct echoaudio *chip)
1011 {
1012         memset(chip->output_gain, ECHOGAIN_MUTED, sizeof(chip->output_gain));
1013         memset(chip->input_gain, ECHOGAIN_MUTED, sizeof(chip->input_gain));
1014         memset(chip->monitor_gain, ECHOGAIN_MUTED, sizeof(chip->monitor_gain));
1015         memset(chip->vmixer_gain, ECHOGAIN_MUTED, sizeof(chip->vmixer_gain));
1016         chip->input_clock = ECHO_CLOCK_INTERNAL;
1017         chip->output_clock = ECHO_CLOCK_WORD;
1018         chip->sample_rate = 44100;
1019         return restore_dsp_rettings(chip);
1020 }
1021
1022
1023
1024 /* This is low level part of the interrupt handler.
1025 It returns -1 if the IRQ is not ours, or N>=0 if it is, where N is the number
1026 of midi data in the input queue. */
1027 static int service_irq(struct echoaudio *chip)
1028 {
1029         int st;
1030
1031         /* Read the DSP status register and see if this DSP generated this interrupt */
1032         if (get_dsp_register(chip, CHI32_STATUS_REG) & CHI32_STATUS_IRQ) {
1033                 st = 0;
1034 #ifdef ECHOCARD_HAS_MIDI
1035                 /* Get and parse midi data if present */
1036                 if (chip->comm_page->midi_input[0])     /* The count is at index 0 */
1037                         st = midi_service_irq(chip);    /* Returns how many midi bytes we received */
1038 #endif
1039                 /* Clear the hardware interrupt */
1040                 chip->comm_page->midi_input[0] = 0;
1041                 send_vector(chip, DSP_VC_ACK_INT);
1042                 return st;
1043         }
1044         return -1;
1045 }
1046
1047
1048
1049
1050 /******************************************************************************
1051         Functions for opening and closing pipes
1052  ******************************************************************************/
1053
1054 /* allocate_pipes is used to reserve audio pipes for your exclusive use.
1055 The call will fail if some pipes are already allocated. */
1056 static int allocate_pipes(struct echoaudio *chip, struct audiopipe *pipe,
1057                           int pipe_index, int interleave)
1058 {
1059         int i;
1060         u32 channel_mask;
1061         char is_cyclic;
1062
1063         dev_dbg(chip->card->dev,
1064                 "allocate_pipes: ch=%d int=%d\n", pipe_index, interleave);
1065
1066         if (chip->bad_board)
1067                 return -EIO;
1068
1069         is_cyclic = 1;  /* This driver uses cyclic buffers only */
1070
1071         for (channel_mask = i = 0; i < interleave; i++)
1072                 channel_mask |= 1 << (pipe_index + i);
1073         if (chip->pipe_alloc_mask & channel_mask) {
1074                 dev_err(chip->card->dev,
1075                         "allocate_pipes: channel already open\n");
1076                 return -EAGAIN;
1077         }
1078
1079         chip->comm_page->position[pipe_index] = 0;
1080         chip->pipe_alloc_mask |= channel_mask;
1081         if (is_cyclic)
1082                 chip->pipe_cyclic_mask |= channel_mask;
1083         pipe->index = pipe_index;
1084         pipe->interleave = interleave;
1085         pipe->state = PIPE_STATE_STOPPED;
1086
1087         /* The counter register is where the DSP writes the 32 bit DMA
1088         position for a pipe.  The DSP is constantly updating this value as
1089         it moves data. The DMA counter is in units of bytes, not samples. */
1090         pipe->dma_counter = &chip->comm_page->position[pipe_index];
1091         *pipe->dma_counter = 0;
1092         return pipe_index;
1093 }
1094
1095
1096
1097 static int free_pipes(struct echoaudio *chip, struct audiopipe *pipe)
1098 {
1099         u32 channel_mask;
1100         int i;
1101
1102         if (snd_BUG_ON(!is_pipe_allocated(chip, pipe->index)))
1103                 return -EINVAL;
1104         if (snd_BUG_ON(pipe->state != PIPE_STATE_STOPPED))
1105                 return -EINVAL;
1106
1107         for (channel_mask = i = 0; i < pipe->interleave; i++)
1108                 channel_mask |= 1 << (pipe->index + i);
1109
1110         chip->pipe_alloc_mask &= ~channel_mask;
1111         chip->pipe_cyclic_mask &= ~channel_mask;
1112         return 0;
1113 }
1114
1115
1116
1117 /******************************************************************************
1118         Functions for managing the scatter-gather list
1119 ******************************************************************************/
1120
1121 static int sglist_init(struct echoaudio *chip, struct audiopipe *pipe)
1122 {
1123         pipe->sglist_head = 0;
1124         memset(pipe->sgpage.area, 0, PAGE_SIZE);
1125         chip->comm_page->sglist_addr[pipe->index].addr =
1126                 cpu_to_le32(pipe->sgpage.addr);
1127         return 0;
1128 }
1129
1130
1131
1132 static int sglist_add_mapping(struct echoaudio *chip, struct audiopipe *pipe,
1133                                 dma_addr_t address, size_t length)
1134 {
1135         int head = pipe->sglist_head;
1136         struct sg_entry *list = (struct sg_entry *)pipe->sgpage.area;
1137
1138         if (head < MAX_SGLIST_ENTRIES - 1) {
1139                 list[head].addr = cpu_to_le32(address);
1140                 list[head].size = cpu_to_le32(length);
1141                 pipe->sglist_head++;
1142         } else {
1143                 dev_err(chip->card->dev, "SGlist: too many fragments\n");
1144                 return -ENOMEM;
1145         }
1146         return 0;
1147 }
1148
1149
1150
1151 static inline int sglist_add_irq(struct echoaudio *chip, struct audiopipe *pipe)
1152 {
1153         return sglist_add_mapping(chip, pipe, 0, 0);
1154 }
1155
1156
1157
1158 static inline int sglist_wrap(struct echoaudio *chip, struct audiopipe *pipe)
1159 {
1160         return sglist_add_mapping(chip, pipe, pipe->sgpage.addr, 0);
1161 }