+ The `configure' script accompanying GAS does not provide any query
+facility to list all supported host and target names or aliases.
+`configure' calls the Bourne shell script `config.sub' to map
+abbreviations to full names; you can read the script, if you wish, or
+you can use it to test your guesses on abbreviations--for example:
+
+ % sh config.sub sun4
+ sparc-sun-sunos411
+ % sh config.sub sun3
+ m68k-sun-sunos411
+ % sh config.sub decstation
+ mips-dec-ultrix42
+ % sh config.sub hp300bsd
+ m68k-hp-bsd
+ % sh config.sub i386v
+ i386-unknown-sysv
+ % sh config.sub i786v
+ Invalid configuration `i786v': machine `i786v' not recognized
+
+
+`configure' options
+===================
+
+ Here is a summary of the `configure' options and arguments that are
+most often useful for building GAS. `configure' also has several other
+options not listed here.
+
+ configure [--help]
+ [--prefix=DIR]
+ [--srcdir=PATH]
+ [--host=HOST]
+ [--target=TARGET]
+ [--with-OPTION]
+ [--enable-OPTION]
+
+You may introduce options with a single `-' rather than `--' if you
+prefer; but you may abbreviate option names if you use `--'.
+
+`--help'
+ Print a summary of the options to `configure', and exit.
+
+`-prefix=DIR'
+ Configure the source to install programs and files under directory
+ `DIR'.
+
+`--srcdir=PATH'
+ Look for the package's source code in directory DIR. Usually
+ `configure' can determine that directory automatically.
+
+`--host=HOST'
+ Configure GAS to run on the specified HOST. Normally the
+ configure script can figure this out automatically.
+
+ There is no convenient way to generate a list of all available
+ hosts.
+
+`--target=TARGET'
+ Configure GAS for cross-assembling programs for the specified
+ TARGET. Without this option, GAS is configured to assemble .o files
+ that run on the same machine (HOST) as GAS itself.
+
+ There is no convenient way to generate a list of all available
+ targets.
+
+`--enable-OPTION'
+ These flags tell the program or library being configured to
+ configure itself differently from the default for the specified
+ host/target combination. See below for a list of `--enable'
+ options recognized in the gas distribution.
+
+`configure' accepts other options, for compatibility with configuring
+other GNU tools recursively; but these are the only options that affect
+GAS or its supporting libraries.
+
+The `--enable' options recognized by software in the gas distribution are:
+
+`--enable-targets=...'
+ This causes one or more specified configurations to be added to those for
+ which BFD support is compiled. Currently gas cannot use any format other
+ than its compiled-in default, so this option is not very useful.
+
+`--enable-bfd-assembler'
+ This causes the assembler to use the new code being merged into it to use
+ BFD data structures internally, and use BFD for writing object files.
+ For most targets, this isn't supported yet. For most targets where it has
+ been done, it's already the default. So generally you won't need to use
+ this option.
+
+Supported platforms
+===================
+
+At this point I believe gas to be ANSI only code for most target cpu's. That
+is, there should be relatively few, if any host system dependencies. So
+porting (as a cross-assembler) to hosts not yet supported should be fairly
+easy. Porting to a new target shouldn't be too tough if it's a variant of one
+already supported.
+
+Native assembling should work on:
+
+ sun3
+ sun4
+ 386bsd
+ bsd/386
+ delta (m68k-sysv from Motorola)
+ delta88 (m88k-sysv from Motorola)
+ GNU/linux
+ m68k hpux 8.0 (hpux 7.0 may be a problem)
+ vax bsd, ultrix, vms
+ hp9000s300
+ decstation
+ irix 4
+ irix 5
+ miniframe (m68k-sysv from Convergent Technologies)
+ i386-aix (ps/2)
+ hppa (hpux 4.3bsd, osf1)
+ AIX
+ unixware
+ sco 3.2v4.2
+ sco openserver 5.0 (a.k.a. 3.2v5.0 )
+ sparc solaris
+ ns32k (netbsd, lites)
+
+I believe that gas as a cross-assembler can currently be targeted for
+most of the above hosts, plus
+
+ arm
+ decstation-bsd (a.out format, to be used in BSD 4.4)
+ ebmon29k
+ go32 (DOS on i386, with DJGPP -- old a.out version)
+ H8/300, H8/500 (Hitachi)
+ i386-aix (ps/2)
+ i960-coff
+ mips ecoff (decstation-ultrix, iris, mips magnum, mips-idt-ecoff)
+ Mitsubishi d10v and d30v
+ nindy960
+ powerpc EABI
+ SH (Hitachi)
+ sco386
+ TI tic30 and tic80
+ vax bsd or ultrix?
+ vms
+ vxworks68k
+ vxworks960
+ z8000 (Zilog)
+
+MIPS ECOFF support has been added, but GAS will not run a C-style
+preprocessor. If you want that, rename your file to have a ".S" suffix, and
+run gcc on it. Or run "gcc -xassembler-with-cpp foo.s".
+
+Support for ELF should work now for sparc, hppa, i386, alpha, m68k,
+MIPS, powerpc.
+
+Support for sequent (ns32k), tahoe, i860 may be suffering from bitrot.
+
+If you try out gas on some host or target not listed above, please let me know
+the results, so I can update the list.
+
+Compiler Support Hacks
+======================
+
+On a few targets, the assembler has been modified to support a feature
+that is potentially useful when assembling compiler output, but which
+may confuse assembly language programmers. If assembler encounters a
+.word pseudo-op of the form symbol1-symbol2 (the difference of two
+symbols), and the difference of those two symbols will not fit in 16
+bits, the assembler will create a branch around a long jump to
+symbol1, and insert this into the output directly before the next
+label: The .word will (instead of containing garbage, or giving an
+error message) contain (the address of the long jump)-symbol2. This
+allows the assembler to assemble jump tables that jump to locations
+very far away into code that works properly. If the next label is
+more than 32K away from the .word, you lose (silently); RMS claims
+this will never happen. If the -K option is given, you will get a
+warning message when this happens.