depends on PLAT_SAMSUNG
select DEBUG_EXYNOS_UART if ARCH_EXYNOS
select DEBUG_S3C24XX_UART if ARCH_S3C24XX
- bool "Use S3C UART 0 for low-level debug"
+ select DEBUG_S5PV210_UART if ARCH_S5PV210
+ bool "Use Samsung S3C UART 0 for low-level debug"
help
Say Y here if you want the debug print routines to direct
their output to UART 0. The port must have been initialised
by the boot-loader before use.
- The uncompressor code port configuration is now handled
- by CONFIG_S3C_LOWLEVEL_UART_PORT.
-
config DEBUG_S3C_UART1
depends on PLAT_SAMSUNG
select DEBUG_EXYNOS_UART if ARCH_EXYNOS
select DEBUG_S3C24XX_UART if ARCH_S3C24XX
- bool "Use S3C UART 1 for low-level debug"
+ select DEBUG_S5PV210_UART if ARCH_S5PV210
+ bool "Use Samsung S3C UART 1 for low-level debug"
help
Say Y here if you want the debug print routines to direct
their output to UART 1. The port must have been initialised
by the boot-loader before use.
- The uncompressor code port configuration is now handled
- by CONFIG_S3C_LOWLEVEL_UART_PORT.
-
config DEBUG_S3C_UART2
depends on PLAT_SAMSUNG
select DEBUG_EXYNOS_UART if ARCH_EXYNOS
select DEBUG_S3C24XX_UART if ARCH_S3C24XX
- bool "Use S3C UART 2 for low-level debug"
+ select DEBUG_S5PV210_UART if ARCH_S5PV210
+ bool "Use Samsung S3C UART 2 for low-level debug"
help
Say Y here if you want the debug print routines to direct
their output to UART 2. The port must have been initialised
by the boot-loader before use.
- The uncompressor code port configuration is now handled
- by CONFIG_S3C_LOWLEVEL_UART_PORT.
-
config DEBUG_S3C_UART3
- depends on PLAT_SAMSUNG && ARCH_EXYNOS
- select DEBUG_EXYNOS_UART
- bool "Use S3C UART 3 for low-level debug"
+ depends on PLAT_SAMSUNG && (ARCH_EXYNOS || ARCH_S5PV210)
+ select DEBUG_EXYNOS_UART if ARCH_EXYNOS
+ select DEBUG_S5PV210_UART if ARCH_S5PV210
+ bool "Use Samsung S3C UART 3 for low-level debug"
help
Say Y here if you want the debug print routines to direct
their output to UART 3. The port must have been initialised
by the boot-loader before use.
- The uncompressor code port configuration is now handled
- by CONFIG_S3C_LOWLEVEL_UART_PORT.
-
config DEBUG_S3C2410_UART0
depends on ARCH_S3C24XX
select DEBUG_S3C2410_UART
config DEBUG_S3C24XX_UART
bool
+config DEBUG_S5PV210_UART
+ bool
+
config DEBUG_OMAP2PLUS_UART
bool
depends on ARCH_OMAP2PLUS
default "debug/msm.S" if DEBUG_MSM_UART || DEBUG_QCOM_UARTDM
default "debug/omap2plus.S" if DEBUG_OMAP2PLUS_UART
default "debug/s3c24xx.S" if DEBUG_S3C24XX_UART
+ default "debug/s5pv210.S" if DEBUG_S5PV210_UART
default "debug/sirf.S" if DEBUG_SIRFPRIMA2_UART1 || DEBUG_SIRFMARCO_UART1
default "debug/sti.S" if DEBUG_STI_UART
default "debug/tegra.S" if DEBUG_TEGRA_UART