#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/clk.h>
+#include <linux/err.h>
#include <mach/hardware.h>
#include <mach/irqs.h>
#include <plat/control.h>
#include <plat/tc.h>
#include <plat/board.h>
-#include <plat/mux.h>
#include <mach/gpio.h>
#include <plat/mmc.h>
#include <plat/dma.h>
+#include <plat/omap_hwmod.h>
+#include <plat/omap_device.h>
#include "mux.h"
{
.start = INT_24XX_MAIL_U0_MPU,
.flags = IORESOURCE_IRQ,
+ .name = "dsp",
},
{
.start = INT_24XX_MAIL_U3_MPU,
.flags = IORESOURCE_IRQ,
+ .name = "iva",
},
};
static int omap2_mbox_resources_sz = ARRAY_SIZE(omap2_mbox_resources);
{
.start = INT_24XX_MAIL_U0_MPU,
.flags = IORESOURCE_IRQ,
+ .name = "dsp",
},
};
static int omap3_mbox_resources_sz = ARRAY_SIZE(omap3_mbox_resources);
{
.start = OMAP44XX_IRQ_MAIL_U0,
.flags = IORESOURCE_IRQ,
+ .name = "mbox",
},
};
static int omap4_mbox_resources_sz = ARRAY_SIZE(omap4_mbox_resources);
#endif
static struct platform_device mbox_device = {
- .name = "omap2-mailbox",
+ .name = "omap-mailbox",
.id = -1,
};
static inline void omap_init_mbox(void) { }
#endif /* CONFIG_OMAP_MBOX_FWK */
-#if defined(CONFIG_OMAP_STI)
-
-#if defined(CONFIG_ARCH_OMAP2)
-
-#define OMAP2_STI_BASE 0x48068000
-#define OMAP2_STI_CHANNEL_BASE 0x54000000
-#define OMAP2_STI_IRQ 4
-
-static struct resource sti_resources[] = {
- {
- .start = OMAP2_STI_BASE,
- .end = OMAP2_STI_BASE + 0x7ff,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = OMAP2_STI_CHANNEL_BASE,
- .end = OMAP2_STI_CHANNEL_BASE + SZ_64K - 1,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = OMAP2_STI_IRQ,
- .flags = IORESOURCE_IRQ,
- }
-};
-#elif defined(CONFIG_ARCH_OMAP3)
-
-#define OMAP3_SDTI_BASE 0x54500000
-#define OMAP3_SDTI_CHANNEL_BASE 0x54600000
-
-static struct resource sti_resources[] = {
- {
- .start = OMAP3_SDTI_BASE,
- .end = OMAP3_SDTI_BASE + 0xFFF,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = OMAP3_SDTI_CHANNEL_BASE,
- .end = OMAP3_SDTI_CHANNEL_BASE + SZ_1M - 1,
- .flags = IORESOURCE_MEM,
- }
-};
-
-#endif
-
-static struct platform_device sti_device = {
- .name = "sti",
- .id = -1,
- .num_resources = ARRAY_SIZE(sti_resources),
- .resource = sti_resources,
-};
-
-static inline void omap_init_sti(void)
-{
- platform_device_register(&sti_device);
-}
-#else
static inline void omap_init_sti(void) {}
-#endif
#if defined(CONFIG_SPI_OMAP24XX) || defined(CONFIG_SPI_OMAP24XX_MODULE)
static inline void omap_init_sham(void) { }
#endif
+#if defined(CONFIG_CRYPTO_DEV_OMAP_AES) || defined(CONFIG_CRYPTO_DEV_OMAP_AES_MODULE)
+
+#ifdef CONFIG_ARCH_OMAP2
+static struct resource omap2_aes_resources[] = {
+ {
+ .start = OMAP24XX_SEC_AES_BASE,
+ .end = OMAP24XX_SEC_AES_BASE + 0x4C,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = OMAP24XX_DMA_AES_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ {
+ .start = OMAP24XX_DMA_AES_RX,
+ .flags = IORESOURCE_DMA,
+ }
+};
+static int omap2_aes_resources_sz = ARRAY_SIZE(omap2_aes_resources);
+#else
+#define omap2_aes_resources NULL
+#define omap2_aes_resources_sz 0
+#endif
+
+#ifdef CONFIG_ARCH_OMAP3
+static struct resource omap3_aes_resources[] = {
+ {
+ .start = OMAP34XX_SEC_AES_BASE,
+ .end = OMAP34XX_SEC_AES_BASE + 0x4C,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = OMAP34XX_DMA_AES2_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ {
+ .start = OMAP34XX_DMA_AES2_RX,
+ .flags = IORESOURCE_DMA,
+ }
+};
+static int omap3_aes_resources_sz = ARRAY_SIZE(omap3_aes_resources);
+#else
+#define omap3_aes_resources NULL
+#define omap3_aes_resources_sz 0
+#endif
+
+static struct platform_device aes_device = {
+ .name = "omap-aes",
+ .id = -1,
+};
+
+static void omap_init_aes(void)
+{
+ if (cpu_is_omap24xx()) {
+ aes_device.resource = omap2_aes_resources;
+ aes_device.num_resources = omap2_aes_resources_sz;
+ } else if (cpu_is_omap34xx()) {
+ aes_device.resource = omap3_aes_resources;
+ aes_device.num_resources = omap3_aes_resources_sz;
+ } else {
+ pr_err("%s: platform not supported\n", __func__);
+ return;
+ }
+ platform_device_register(&aes_device);
+}
+
+#else
+static inline void omap_init_aes(void) { }
+#endif
+
/*-------------------------------------------------------------------------*/
#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_ARCH_OMAP4)
OMAP_PIN_INPUT_PULLUP);
if (cpu_is_omap2420() && controller_nr == 0) {
- omap_cfg_reg(H18_24XX_MMC_CMD);
- omap_cfg_reg(H15_24XX_MMC_CLKI);
- omap_cfg_reg(G19_24XX_MMC_CLKO);
- omap_cfg_reg(F20_24XX_MMC_DAT0);
- omap_cfg_reg(F19_24XX_MMC_DAT_DIR0);
- omap_cfg_reg(G18_24XX_MMC_CMD_DIR);
- if (mmc_controller->slots[0].wires == 4) {
- omap_cfg_reg(H14_24XX_MMC_DAT1);
- omap_cfg_reg(E19_24XX_MMC_DAT2);
- omap_cfg_reg(D19_24XX_MMC_DAT3);
- omap_cfg_reg(E20_24XX_MMC_DAT_DIR1);
- omap_cfg_reg(F18_24XX_MMC_DAT_DIR2);
- omap_cfg_reg(E18_24XX_MMC_DAT_DIR3);
+ omap_mux_init_signal("sdmmc_cmd", 0);
+ omap_mux_init_signal("sdmmc_clki", 0);
+ omap_mux_init_signal("sdmmc_clko", 0);
+ omap_mux_init_signal("sdmmc_dat0", 0);
+ omap_mux_init_signal("sdmmc_dat_dir0", 0);
+ omap_mux_init_signal("sdmmc_cmd_dir", 0);
+ if (mmc_controller->slots[0].caps & MMC_CAP_4_BIT_DATA) {
+ omap_mux_init_signal("sdmmc_dat1", 0);
+ omap_mux_init_signal("sdmmc_dat2", 0);
+ omap_mux_init_signal("sdmmc_dat3", 0);
+ omap_mux_init_signal("sdmmc_dat_dir1", 0);
+ omap_mux_init_signal("sdmmc_dat_dir2", 0);
+ omap_mux_init_signal("sdmmc_dat_dir3", 0);
}
/*
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc1_dat0",
OMAP_PIN_INPUT_PULLUP);
- if (mmc_controller->slots[0].wires == 4 ||
- mmc_controller->slots[0].wires == 8) {
+ if (mmc_controller->slots[0].caps &
+ (MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA)) {
omap_mux_init_signal("sdmmc1_dat1",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc1_dat2",
omap_mux_init_signal("sdmmc1_dat3",
OMAP_PIN_INPUT_PULLUP);
}
- if (mmc_controller->slots[0].wires == 8) {
+ if (mmc_controller->slots[0].caps &
+ MMC_CAP_8_BIT_DATA) {
omap_mux_init_signal("sdmmc1_dat4",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc1_dat5",
* For 8 wire configurations, Lines DAT4, 5, 6 and 7 need to be muxed
* in the board-*.c files
*/
- if (mmc_controller->slots[0].wires == 4 ||
- mmc_controller->slots[0].wires == 8) {
+ if (mmc_controller->slots[0].caps &
+ (MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA)) {
omap_mux_init_signal("sdmmc2_dat1",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc2_dat2",
omap_mux_init_signal("sdmmc2_dat3",
OMAP_PIN_INPUT_PULLUP);
}
- if (mmc_controller->slots[0].wires == 8) {
+ if (mmc_controller->slots[0].caps &
+ MMC_CAP_8_BIT_DATA) {
omap_mux_init_signal("sdmmc2_dat4.sdmmc2_dat4",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc2_dat5.sdmmc2_dat5",
case 3:
if (!cpu_is_omap44xx())
return;
- base = OMAP4_MMC4_BASE + OMAP4_MMC_REG_OFFSET;
+ base = OMAP4_MMC4_BASE;
irq = OMAP44XX_IRQ_MMC4;
break;
case 4:
if (!cpu_is_omap44xx())
return;
- base = OMAP4_MMC5_BASE + OMAP4_MMC_REG_OFFSET;
+ base = OMAP4_MMC5_BASE;
irq = OMAP44XX_IRQ_MMC5;
break;
default:
size = OMAP2420_MMC_SIZE;
name = "mmci-omap";
} else if (cpu_is_omap44xx()) {
- if (i < 3) {
- base += OMAP4_MMC_REG_OFFSET;
+ if (i < 3)
irq += OMAP44XX_IRQ_GIC_START;
- }
size = OMAP4_HSMMC_SIZE;
name = "mmci-omap-hs";
} else {
/*-------------------------------------------------------------------------*/
+/*
+ * Inorder to avoid any assumptions from bootloader regarding WDT
+ * settings, WDT module is reset during init. This enables the watchdog
+ * timer. Hence it is required to disable the watchdog after the WDT reset
+ * during init. Otherwise the system would reboot as per the default
+ * watchdog timer registers settings.
+ */
+#define OMAP_WDT_WPS (0x34)
+#define OMAP_WDT_SPR (0x48)
+
+static int omap2_disable_wdt(struct omap_hwmod *oh, void *unused)
+{
+ void __iomem *base;
+ int ret;
+
+ if (!oh) {
+ pr_err("%s: Could not look up wdtimer_hwmod\n", __func__);
+ return -EINVAL;
+ }
+
+ base = omap_hwmod_get_mpu_rt_va(oh);
+ if (!base) {
+ pr_err("%s: Could not get the base address for %s\n",
+ oh->name, __func__);
+ return -EINVAL;
+ }
+
+ /* Enable the clocks before accessing the WDT registers */
+ ret = omap_hwmod_enable(oh);
+ if (ret) {
+ pr_err("%s: Could not enable clocks for %s\n",
+ oh->name, __func__);
+ return ret;
+ }
+
+ /* sequence required to disable watchdog */
+ __raw_writel(0xAAAA, base + OMAP_WDT_SPR);
+ while (__raw_readl(base + OMAP_WDT_WPS) & 0x10)
+ cpu_relax();
+
+ __raw_writel(0x5555, base + OMAP_WDT_SPR);
+ while (__raw_readl(base + OMAP_WDT_WPS) & 0x10)
+ cpu_relax();
+
+ ret = omap_hwmod_idle(oh);
+ if (ret)
+ pr_err("%s: Could not disable clocks for %s\n",
+ oh->name, __func__);
+
+ return ret;
+}
+
+static void __init omap_disable_wdt(void)
+{
+ if (cpu_class_is_omap2())
+ omap_hwmod_for_each_by_class("wd_timer",
+ omap2_disable_wdt, NULL);
+ return;
+}
+
static int __init omap2_init_devices(void)
{
/* please keep these calls, and their implementations above,
* in alphabetical order so they're easier to sort through.
*/
+ omap_disable_wdt();
omap_hsmmc_reset();
omap_init_camera();
omap_init_mbox();
omap_hdq_init();
omap_init_sti();
omap_init_sham();
+ omap_init_aes();
omap_init_vout();
return 0;
}
arch_initcall(omap2_init_devices);
+
+#if defined(CONFIG_OMAP_WATCHDOG) || defined(CONFIG_OMAP_WATCHDOG_MODULE)
+struct omap_device_pm_latency omap_wdt_latency[] = {
+ [0] = {
+ .deactivate_func = omap_device_idle_hwmods,
+ .activate_func = omap_device_enable_hwmods,
+ .flags = OMAP_DEVICE_LATENCY_AUTO_ADJUST,
+ },
+};
+
+static int __init omap_init_wdt(void)
+{
+ int id = -1;
+ struct omap_device *od;
+ struct omap_hwmod *oh;
+ char *oh_name = "wd_timer2";
+ char *dev_name = "omap_wdt";
+
+ if (!cpu_class_is_omap2())
+ return 0;
+
+ oh = omap_hwmod_lookup(oh_name);
+ if (!oh) {
+ pr_err("Could not look up wd_timer%d hwmod\n", id);
+ return -EINVAL;
+ }
+
+ od = omap_device_build(dev_name, id, oh, NULL, 0,
+ omap_wdt_latency,
+ ARRAY_SIZE(omap_wdt_latency), 0);
+ WARN(IS_ERR(od), "Cant build omap_device for %s:%s.\n",
+ dev_name, oh->name);
+ return 0;
+}
+subsys_initcall(omap_init_wdt);
+#endif