# Get 'install' or 'install-sh' and its variants.
AC_PROG_INSTALL
+AC_PROG_LN_S
sinclude(config/acx.m4)
# these libraries are used by various programs built for the host environment
#
-host_libs="intl mmalloc libiberty opcodes bfd readline tcl tk itcl tix libgui zlib"
+host_libs="intl mmalloc libiberty opcodes bfd readline tcl tk itcl tix libgui zlib libbanshee libcpp"
# these tools are built for the host environment
# Note, the powerpc-eabi build depends on sim occurring before gdb in order to
target-libgloss \
target-newlib \
target-libstdc++-v3 \
- target-libf2c \
+ target-libmudflap \
+ target-libgfortran \
${libgcj} \
target-libobjc \
target-libada"
;;
esac
+AC_ARG_WITH(libbanshee,
+[ --without-libbanshee Don't build with libbanshee])
+case ${with_libbanshee} in
+ no)
+ noconfigdirs="$noconfigdirs libbanshee" ;;
+ yes|"")
+ with_libbanshee=yes
+ ;;
+ *)
+ AC_MSG_ERROR([--with-libbanshee can only be empty, "yes" or "no" (empty defaults to "yes".])
+esac
+
AC_ARG_ENABLE(libada,
[ --enable-libada Builds libada directory],
ENABLE_LIBADA=$enableval,
;;
esac
+
+# Allow --disable-libmudflap to exclude target-libmudflap
+case $enable_libmudflap in
+yes | "")
+ # By default it's enabled
+ ;;
+no)
+ noconfigdirs="$noconfigdirs target-libmudflap"
+ ;;
+esac
+
+
case "${target}" in
*-*-chorusos)
noconfigdirs="$noconfigdirs target-newlib target-libgloss ${libgcj}"
*-*-freebsd[[12]] | *-*-freebsd[[12]].* | *-*-freebsd*aout*)
noconfigdirs="$noconfigdirs target-newlib target-libgloss ${libgcj}"
;;
+ *-*-freebsd* | *-*-kfreebsd*-gnu)
+ noconfigdirs="$noconfigdirs target-newlib target-libgloss"
+ if test "x$with_gmp" = x && test "x$with_gmp_dir" = x \
+ && test -f /usr/local/include/gmp.h; then
+ with_gmp=/usr/local
+ fi
+
+ # Skip some stuff that's unsupported on some FreeBSD configurations.
+ case "${target}" in
+ i*86-*-*) ;;
+ alpha*-*-*) ;;
+ *)
+ noconfigdirs="$noconfigdirs ${libgcj}"
+ ;;
+ esac
+ ;;
*-*-kaos*)
# Remove unsupported stuff on all kaOS configurations.
- skipdirs="target-libiberty ${libgcj} target-libstdc++-v3 target-libf2c target-librx"
+ skipdirs="target-libiberty ${libgcj} target-libstdc++-v3 target-librx"
skipdirs="$skipdirs target-libobjc target-examples target-groff target-gperf"
skipdirs="$skipdirs zlib fastjar target-libjava target-boehm-gc target-zlib"
noconfigdirs="$noconfigdirs target-libgloss"
;;
*-*-rtems*)
noconfigdirs="$noconfigdirs target-libgloss ${libgcj}"
- case ${target} in
- h8300*-*-* | h8500-*-*)
- noconfigdirs="$noconfigdirs target-libf2c"
- ;;
- *) ;;
- esac
;;
*-*-uclinux*)
noconfigdirs="$noconfigdirs target-newlib target-libgloss target-rda ${libgcj}"
# newlib is not 64 bit ready
noconfigdirs="$noconfigdirs target-newlib target-libgloss"
;;
- alpha*-*-freebsd* | alpha*-*-kfreebsd*-gnu)
- noconfigdirs="$noconfigdirs target-newlib target-libgloss"
- ;;
alpha*-*-*)
# newlib is not 64 bit ready
noconfigdirs="$noconfigdirs target-newlib target-libgloss ${libgcj}"
noconfigdirs="$noconfigdirs ${libgcj}"
;;
h8300*-*-*)
- noconfigdirs="$noconfigdirs target-libgloss ${libgcj} target-libf2c"
+ noconfigdirs="$noconfigdirs target-libgloss ${libgcj}"
;;
h8500-*-*)
- noconfigdirs="$noconfigdirs target-libstdc++-v3 target-libgloss ${libgcj} target-libf2c"
+ noconfigdirs="$noconfigdirs target-libstdc++-v3 target-libgloss ${libgcj}"
;;
hppa*64*-*-linux* | parisc*64*-*-linux*)
# In this case, it's because the hppa64-linux target is for
i[[3456789]]86-*-coff | i[[3456789]]86-*-elf)
noconfigdirs="$noconfigdirs ${libgcj}"
;;
- i[[3456789]]86-*-freebsd* | i[[3456789]]86-*-kfreebsd*-gnu)
- noconfigdirs="$noconfigdirs target-newlib target-libgloss"
- ;;
i[[3456789]]86-*-linux*)
# The GCC port for glibc1 has no MD_FALLBACK_FRAME_STATE_FOR, so let's
# not build java stuff by default.
ACX_PROG_GNAT
ACX_PROG_CMP_IGNORE_INITIAL
+# Check for GMP
+gmplibs=
+gmpinc=
+have_gmp=yes
+# Specify a location for gmp
+AC_ARG_WITH(gmp-dir, [ --with-gmp-dir=PATH Specify source directory for GMP library])
+
+if test "x$with_gmp_dir" != x && test -f "$with_gmp_dir/gmp.h"; then
+ gmpinc="-I$with_gmp_dir"
+ if test -f "$with_gmp_dir/.libs/libgmp.a"; then
+ gmplibs="$with_gmp_dir/.libs/libgmp.a"
+ elif test -f "$with_gmp_dir/_libs/libgmp.a"; then
+ gmplibs="$with_gmp_dir/_libs/libgmp.a"
+ fi
+ # One of the later tests will catch the error if neither library is present.
+fi
+
+AC_ARG_WITH(gmp, [ --with-gmp=PATH Specify directory for installed GMP library])
+
+if test "x$with_gmp" != x && test -d "$with_gmp"; then
+ gmplibs="-L$with_gmp/lib -lgmp"
+ gmpinc="-I$with_gmp/include"
+fi
+
+# Use system gmp if nothing else specified
+if test "x$gmplibs" = x; then
+ gmplibs="-lgmp"
+fi
+
+saved_CFLAGS="$CFLAGS"
+CFLAGS="$CFLAGS $gmpinc"
+# Check GMP actually works
+AC_MSG_CHECKING([for correct version of gmp.h])
+AC_TRY_COMPILE([#include "gmp.h"],[
+#if __GNU_MP_VERSION < 3
+choke me
+#endif
+], [AC_MSG_RESULT([yes])],
+ [AC_MSG_RESULT([no]); have_gmp=no])
+
+if test x"$have_gmp" = xyes; then
+ AC_MSG_CHECKING([for mpf_init in -lgmp])
+
+ saved_LIBS="$LIBS"
+ LIBS="$LIBS $gmplibs"
+ AC_TRY_LINK([#include <gmp.h>], [mpf_t n; mpf_init(n);],
+ [AC_MSG_RESULT([yes])], [AC_MSG_RESULT([no]); have_gmp=no])
+ LIBS="$saved_LIBS"
+ CFLAGS="$saved_CFLAGS"
+fi
+
+AC_SUBST(gmplibs)
+AC_SUBST(gmpinc)
+
# By default, C is the only stage 1 language.
stage1_languages=c
AC_SUBST(stage1_languages)
lang_dirs=
boot_language=
build_by_default=
+ need_gmp=
. ${lang_frag}
# This is quite sensitive to the ordering of the case statement arms.
case ,${enable_languages},:${language}:${have_gnat}:${build_by_default} in
add_this_lang=no
;;
esac
- case $add_this_lang in
+
+ # Disable language that need GMP if it isn't available.
+ if test x"$need_gmp" = xyes && test x"$have_gmp" = xno; then
+ add_this_lang=no
+ fi
+
+ case $add_this_lang in
no)
# Remove language-dependent dirs.
eval noconfigdirs='"$noconfigdirs "'\"$target_libs $lang_dirs\"
extra_host_args="$extra_host_args --with-newlib"
fi
+if test x${with_libbanshee} = xyes && echo " ${configdirs} " | grep " libbanshee " >/dev/null 2>&1; then
+ extra_host_args="$extra_host_args --with-libbanshee"
+fi
# Default to using --with-stabs for certain targets.
if test x${with_stabs} = x ; then
;;
esac
-# Create the 'maybe dependencies'. This uses a temporary file.
+# Strip out unwanted targets.
# While at that, we remove Makefiles if we were started for recursive
# configuration, so that the top-level Makefile reconfigures them,
# like we used to do when configure itself was recursive.
-rm -f maybedep.tmp
-echo '# maybedep.tmp' > maybedep.tmp
-# Make-targets which may need maybe dependencies.
-mts="configure all install check clean distclean dvi info install-info"
-mts="${mts} installcheck mostlyclean maintainer-clean TAGS"
+# Loop over modules. $extrasub must be used with care, limiting as
+# much as possible the usage of range addresses. That's because autoconf
+# splits the sed script to overcome limits in the number of commands,
+# and relying on carefully-timed sed passes may turn out to be very hard
+# to maintain later. In this particular case, you just have to be careful
+# not to nest @if/@endif pairs, because configure will not warn you at all.
-# Loop over modules and make-targets.
for module in ${build_modules} ; do
if test -z "${no_recursion}" \
&& test -f ${build_subdir}/${module}/Makefile; then
echo 1>&2 "*** removing ${build_subdir}/${module}/Makefile to force reconfigure"
rm -f ${build_subdir}/${module}/Makefile
fi
- for mt in ${mts} ; do
- case ${mt} in
- install) ;; # No installing build modules.
- *) echo "maybe-${mt}-build-${module}: ${mt}-build-${module}" >> maybedep.tmp ;;
- esac
- done
+ extrasub="$extrasub
+/^@if build-$module\$/d
+/^@endif build-$module\$/d"
done
for module in ${configdirs} ; do
if test -z "${no_recursion}" \
echo 1>&2 "*** removing ${module}/Makefile to force reconfigure"
rm -f ${module}/Makefile
fi
- for mt in ${mts} ; do
- echo "maybe-${mt}-${module}: ${mt}-${module}" >> maybedep.tmp
- done
+ extrasub="$extrasub
+/^@if $module\$/d
+/^@endif $module\$/d"
done
for module in ${target_configdirs} ; do
if test -z "${no_recursion}" \
echo 1>&2 "*** removing ${target_subdir}/${module}/Makefile to force reconfigure"
rm -f ${target_subdir}/${module}/Makefile
fi
- for mt in ${mts} ; do
- echo "maybe-${mt}-target-${module}: ${mt}-target-${module}" >> maybedep.tmp
- done
+ extrasub="$extrasub
+/^@if target-$module\$/d
+/^@endif target-$module\$/d"
done
-maybe_dependencies=maybedep.tmp
-AC_SUBST_FILE(maybe_dependencies)
+extrasub="$extrasub
+/^@if /,/^@endif /d"
# Create the serialization dependencies. This uses a temporary file.
fi
GCJ_FOR_TARGET=$GCJ_FOR_TARGET' $(FLAGS_FOR_TARGET)'
+if test "x${GFORTRAN_FOR_TARGET+set}" = xset; then
+ :
+elif test -d ${srcdir}/gcc; then
+ GFORTRAN_FOR_TARGET='$$r/gcc/gfortran -B$$r/gcc/'
+elif test "$host" = "$target"; then
+ GFORTRAN_FOR_TARGET='gfortran'
+else
+ GFORTRAN_FOR_TARGET=`echo gfortran | sed -e 's/x/x/' ${program_transform_name}`
+fi
+case $GFORTRAN_FOR_TARGET in
+*' $(FLAGS_FOR_TARGET)') ;;
+*) GFORTRAN_FOR_TARGET=$GFORTRAN_FOR_TARGET' $(FLAGS_FOR_TARGET)' ;;
+esac
+
# Don't use libstdc++-v3's flags to configure/build itself.
libstdcxx_flags='`test ! -f $$r/$(TARGET_SUBDIR)/libstdc++-v3/scripts/testsuite_flags || $(SHELL) $$r/$(TARGET_SUBDIR)/libstdc++-v3/scripts/testsuite_flags --build-includes` -L$$r/$(TARGET_SUBDIR)/libstdc++-v3/src -L$$r/$(TARGET_SUBDIR)/libstdc++-v3/src/.libs'
raw_libstdcxx_flags='-L$$r/$(TARGET_SUBDIR)/libstdc++-v3/src -L$$r/$(TARGET_SUBDIR)/libstdc++-v3/src/.libs'
# Wrap CC_FOR_TARGET and friends, for certain types of builds.
CC_FOR_TARGET="\$(STAGE_CC_WRAPPER) ${CC_FOR_TARGET}"
GCJ_FOR_TARGET="\$(STAGE_CC_WRAPPER) ${GCJ_FOR_TARGET}"
+GFORTRAN_FOR_TARGET="\$(STAGE_CC_WRAPPER) ${GFORTRAN_FOR_TARGET}"
CXX_FOR_TARGET="\$(STAGE_CC_WRAPPER) ${qCXX_FOR_TARGET}"
RAW_CXX_FOR_TARGET="\$(STAGE_CC_WRAPPER) ${qRAW_CXX_FOR_TARGET}"
CXX_FOR_TARGET_FOR_RECURSIVE_MAKE="\$(STAGE_CC_WRAPPER) ${qqCXX_FOR_TARGET}"
AC_SUBST(FLAGS_FOR_TARGET)
AC_SUBST(CC_FOR_TARGET)
AC_SUBST(GCJ_FOR_TARGET)
+AC_SUBST(GFORTRAN_FOR_TARGET)
AC_SUBST(CXX_FOR_TARGET)
AC_SUBST(RAW_CXX_FOR_TARGET)
AC_SUBST(CXX_FOR_TARGET_FOR_RECURSIVE_MAKE)
esac
AC_SUBST(stage1_cflags)
+# It makes debugging easier if we create as symlinks the stage directories
+# gcc for stageN-gcc and stage-prev for stage(N-1). In case this is not
+# possible, however, we can resort to mv.
+AC_CACHE_CHECK([if symbolic links between directories work],
+[gcc_cv_prog_ln_s_dir],
+[if test "${LN_S}" = "ln -s" \
+ && mkdir confdir.s1 \
+ && ln -s confdir.s1 confdir.s2 \
+ && echo timestamp1 > confdir.s1/conftest.1 \
+ && cmp confdir.s1/conftest.1 confdir.s2/conftest.1 \
+ && echo timestamp2 > confdir.s2/conftest.2 \
+ && cmp confdir.s1/conftest.2 confdir.s1/conftest.2 \
+ && rm -f confdir.s2; then
+ gcc_cv_prog_ln_s_dir=yes
+else
+ gcc_cv_prog_ln_s_dir=yes
+fi
+rm -rf confdir.s1 confdir.s2])
+
+case ${gcc_cv_prog_ln_s_dir} in
+ yes)
+ CREATE_LINK_TO_DIR='ln -s $$1 $$2'
+ UNDO_LINK_TO_DIR='rm -f $$1' ;;
+ *)
+ CREATE_LINK_TO_DIR='mv $$1 $$2'
+ UNDO_LINK_TO_DIR='mv $$1 $$2' ;;
+esac
+AC_SUBST(CREATE_LINK_TO_DIR)
+AC_SUBST(UNDO_LINK_TO_DIR)
+
# Enable -Werror in bootstrap stage2 and later.
# Change the default to "no" on release branches.
AC_ARG_ENABLE(werror,