* @pwrreg_clkgate: MMCIPOWER register must be used to gate the clock
* @busy_detect: true if busy detection on dat0 is supported
* @pwrreg_nopower: bits in MMCIPOWER don't controls ext. power supply
+ * @explicit_mclk_control: enable explicit mclk control in driver.
+ * @qcom_fifo: enables qcom specific fifo pio read logic.
*/
struct variant_data {
unsigned int clkreg;
bool pwrreg_clkgate;
bool busy_detect;
bool pwrreg_nopower;
+ bool explicit_mclk_control;
+ bool qcom_fifo;
};
static struct variant_data variant_arm = {
.pwrreg_nopower = true,
};
+static struct variant_data variant_qcom = {
+ .fifosize = 16 * 4,
+ .fifohalfsize = 8 * 4,
+ .clkreg = MCI_CLK_ENABLE,
+ .clkreg_enable = MCI_QCOM_CLK_FLOWENA |
+ MCI_QCOM_CLK_SELECT_IN_FBCLK,
+ .clkreg_8bit_bus_enable = MCI_QCOM_CLK_WIDEBUS_8,
+ .datactrl_mask_ddrmode = MCI_QCOM_CLK_SELECT_IN_DDR_MODE,
+ .data_cmd_enable = MCI_QCOM_CSPM_DATCMD,
+ .blksz_datactrl4 = true,
+ .datalength_bits = 24,
+ .pwrreg_powerup = MCI_PWR_UP,
+ .f_max = 208000000,
+ .explicit_mclk_control = true,
+ .qcom_fifo = true,
+};
+
static int mmci_card_busy(struct mmc_host *mmc)
{
struct mmci_host *host = mmc_priv(mmc);
host->cclk = 0;
if (desired) {
- if (desired >= host->mclk) {
+ if (variant->explicit_mclk_control) {
+ host->cclk = host->mclk;
+ } else if (desired >= host->mclk) {
clk = MCI_CLK_BYPASS;
if (variant->st_clkdiv)
clk |= MCI_ST_UX500_NEG_EDGE;
}
}
+static int mmci_get_rx_fifocnt(struct mmci_host *host, u32 status, int remain)
+{
+ return remain - (readl(host->base + MMCIFIFOCNT) << 2);
+}
+
+static int mmci_qcom_get_rx_fifocnt(struct mmci_host *host, u32 status, int r)
+{
+ /*
+ * on qcom SDCC4 only 8 words are used in each burst so only 8 addresses
+ * from the fifo range should be used
+ */
+ if (status & MCI_RXFIFOHALFFULL)
+ return host->variant->fifohalfsize;
+ else if (status & MCI_RXDATAAVLBL)
+ return 4;
+
+ return 0;
+}
+
static int mmci_pio_read(struct mmci_host *host, char *buffer, unsigned int remain)
{
void __iomem *base = host->base;
char *ptr = buffer;
- u32 status;
+ u32 status = readl(host->base + MMCISTATUS);
int host_remain = host->size;
do {
- int count = host_remain - (readl(base + MMCIFIFOCNT) << 2);
+ int count = host->get_rx_fifocnt(host, status, host_remain);
if (count > remain)
count = remain;
if (!ios->clock && variant->pwrreg_clkgate)
pwr &= ~MCI_PWR_ON;
+ if (host->variant->explicit_mclk_control &&
+ ios->clock != host->clock_cache) {
+ ret = clk_set_rate(host->clk, ios->clock);
+ if (ret < 0)
+ dev_err(mmc_dev(host->mmc),
+ "Error setting clock rate (%d)\n", ret);
+ else
+ host->mclk = clk_get_rate(host->clk);
+ }
+ host->clock_cache = ios->clock;
+
spin_lock_irqsave(&host->lock, flags);
mmci_set_clkreg(host, ios->clock);
if (ret)
goto host_free;
+ if (variant->qcom_fifo)
+ host->get_rx_fifocnt = mmci_qcom_get_rx_fifocnt;
+ else
+ host->get_rx_fifocnt = mmci_get_rx_fifocnt;
+
host->plat = plat;
host->variant = variant;
host->mclk = clk_get_rate(host->clk);
* The ARM and ST versions of the block have slightly different
* clock divider equations which means that the minimum divider
* differs too.
+ * on Qualcomm like controllers get the nearest minimum clock to 100Khz
*/
if (variant->st_clkdiv)
mmc->f_min = DIV_ROUND_UP(host->mclk, 257);
+ else if (variant->explicit_mclk_control)
+ mmc->f_min = clk_round_rate(host->clk, 100000);
else
mmc->f_min = DIV_ROUND_UP(host->mclk, 512);
/*
* the block, of course.
*/
if (mmc->f_max)
- mmc->f_max = min(host->mclk, mmc->f_max);
+ mmc->f_max = variant->explicit_mclk_control ?
+ min(variant->f_max, mmc->f_max) :
+ min(host->mclk, mmc->f_max);
else
- mmc->f_max = min(host->mclk, fmax);
+ mmc->f_max = variant->explicit_mclk_control ?
+ fmax : min(host->mclk, fmax);
+
+
dev_dbg(mmc_dev(mmc), "clocking block at %u Hz\n", mmc->f_max);
/* Get regulators and the supported OCR mask */
.mask = 0xf0ffffff,
.data = &variant_ux500v2,
},
+ /* Qualcomm variants */
+ {
+ .id = 0x00051180,
+ .mask = 0x000fffff,
+ .data = &variant_qcom,
+ },
{ 0, 0 },
};