[MTD] [NAND] fix possible Ooops in rfc_from4
[deliverable/linux.git] / drivers / mtd / nand / rtc_from4.c
index 4a83a7dd58da222d22008e2fdbad0258d9dc8889..26f88215bc47d48c12ff9768da72829366d4ac76 100644 (file)
@@ -357,7 +357,7 @@ static int rtc_from4_correct_data(struct mtd_info *mtd, const u_char *buf, u_cha
        /* Read the syndrom pattern from the FPGA and correct the bitorder */
        rs_ecc = (volatile unsigned short *)(rtc_from4_fio_base + RTC_FROM4_RS_ECC);
        for (i = 0; i < 8; i++) {
-               ecc[i] = byte_rev_table[(*rs_ecc) & 0xFF];
+               ecc[i] = bitrev8(*rs_ecc);
                rs_ecc++;
        }
 
@@ -456,11 +456,11 @@ static int rtc_from4_errstat(struct mtd_info *mtd, struct nand_chip *this,
                rtn = nand_do_read(mtd, page, len, &retlen, buf);
 
                /* if read failed or > 1-bit error corrected */
-               if (rtn || (mtd->ecc_stats.corrected - corrected) > 1) {
+               if (rtn || (mtd->ecc_stats.corrected - corrected) > 1)
                        er_stat |= 1 << 1;
                kfree(buf);
        }
-
+out:
        rtn = status;
        if (er_stat == 0) {     /* if ECC is available   */
                rtn = (status & ~NAND_STATUS_FAIL);     /*   clear the error bit */
@@ -478,6 +478,7 @@ static int __init rtc_from4_init(void)
        struct nand_chip *this;
        unsigned short bcr1, bcr2, wcr2;
        int i;
+       int ret;
 
        /* Allocate memory for MTD device structure and private data */
        rtc_from4_mtd = kmalloc(sizeof(struct mtd_info) + sizeof(struct nand_chip), GFP_KERNEL);
@@ -537,6 +538,22 @@ static int __init rtc_from4_init(void)
        this->ecc.hwctl = rtc_from4_enable_hwecc;
        this->ecc.calculate = rtc_from4_calculate_ecc;
        this->ecc.correct = rtc_from4_correct_data;
+
+       /* We could create the decoder on demand, if memory is a concern.
+        * This way we have it handy, if an error happens
+        *
+        * Symbolsize is 10 (bits)
+        * Primitve polynomial is x^10+x^3+1
+        * first consecutive root is 0
+        * primitve element to generate roots = 1
+        * generator polinomial degree = 6
+        */
+       rs_decoder = init_rs(10, 0x409, 0, 1, 6);
+       if (!rs_decoder) {
+               printk(KERN_ERR "Could not create a RS decoder\n");
+               ret = -ENOMEM;
+               goto err_1;
+       }
 #else
        printk(KERN_INFO "rtc_from4_init: using software ECC detection.\n");
 
@@ -549,8 +566,8 @@ static int __init rtc_from4_init(void)
 
        /* Scan to find existence of the device */
        if (nand_scan(rtc_from4_mtd, RTC_FROM4_MAX_CHIPS)) {
-               kfree(rtc_from4_mtd);
-               return -ENXIO;
+               ret = -ENXIO;
+               goto err_2;
        }
 
        /* Perform 'device recovery' for each chip in case there was a power loss. */
@@ -566,28 +583,19 @@ static int __init rtc_from4_init(void)
 #endif
 
        /* Register the partitions */
-       add_mtd_partitions(rtc_from4_mtd, partition_info, NUM_PARTITIONS);
+       ret = add_mtd_partitions(rtc_from4_mtd, partition_info, NUM_PARTITIONS);
+       if (ret)
+               goto err_3;
 
-#ifdef RTC_FROM4_HWECC
-       /* We could create the decoder on demand, if memory is a concern.
-        * This way we have it handy, if an error happens
-        *
-        * Symbolsize is 10 (bits)
-        * Primitve polynomial is x^10+x^3+1
-        * first consecutive root is 0
-        * primitve element to generate roots = 1
-        * generator polinomial degree = 6
-        */
-       rs_decoder = init_rs(10, 0x409, 0, 1, 6);
-       if (!rs_decoder) {
-               printk(KERN_ERR "Could not create a RS decoder\n");
-               nand_release(rtc_from4_mtd);
-               kfree(rtc_from4_mtd);
-               return -ENOMEM;
-       }
-#endif
        /* Return happy */
        return 0;
+err_3:
+       nand_release(rtc_from4_mtd);
+err_2:
+       free_rs(rs_decoder);
+err_1:
+       kfree(rtc_from4_mtd);
+       return ret;
 }
 
 module_init(rtc_from4_init);
This page took 0.029222 seconds and 5 git commands to generate.