static s32 igb_reset_hw_82575(struct e1000_hw *);
static s32 igb_set_d0_lplu_state_82575(struct e1000_hw *, bool);
static s32 igb_setup_copper_link_82575(struct e1000_hw *);
-static s32 igb_setup_fiber_serdes_link_82575(struct e1000_hw *);
+static s32 igb_setup_serdes_link_82575(struct e1000_hw *);
static s32 igb_write_phy_reg_sgmii_82575(struct e1000_hw *, u32, u16);
static void igb_clear_hw_cntrs_82575(struct e1000_hw *);
static s32 igb_acquire_swfw_sync_82575(struct e1000_hw *, u16);
-static void igb_configure_pcs_link_82575(struct e1000_hw *);
static s32 igb_get_pcs_speed_and_duplex_82575(struct e1000_hw *, u16 *,
u16 *);
static s32 igb_get_phy_id_82575(struct e1000_hw *);
dev_spec->sgmii_active = false;
ctrl_ext = rd32(E1000_CTRL_EXT);
- if ((ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) ==
- E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES) {
- hw->phy.media_type = e1000_media_type_internal_serdes;
- ctrl_ext |= E1000_CTRL_I2C_ENA;
- } else if (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_SGMII) {
+ switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) {
+ case E1000_CTRL_EXT_LINK_MODE_SGMII:
dev_spec->sgmii_active = true;
ctrl_ext |= E1000_CTRL_I2C_ENA;
- } else {
+ break;
+ case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES:
+ hw->phy.media_type = e1000_media_type_internal_serdes;
+ ctrl_ext |= E1000_CTRL_I2C_ENA;
+ break;
+ default:
ctrl_ext &= ~E1000_CTRL_I2C_ENA;
+ break;
}
+
wr32(E1000_CTRL_EXT, ctrl_ext);
/* Set mta register count */
mac->ops.setup_physical_interface =
(hw->phy.media_type == e1000_media_type_copper)
? igb_setup_copper_link_82575
- : igb_setup_fiber_serdes_link_82575;
+ : igb_setup_serdes_link_82575;
/* NVM initialization */
eecd = rd32(E1000_EECD);
**/
static s32 igb_acquire_phy_82575(struct e1000_hw *hw)
{
- u16 mask;
+ u16 mask = E1000_SWFW_PHY0_SM;
- mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM;
+ if (hw->bus.func == E1000_FUNC_1)
+ mask = E1000_SWFW_PHY1_SM;
return igb_acquire_swfw_sync_82575(hw, mask);
}
**/
static void igb_release_phy_82575(struct e1000_hw *hw)
{
- u16 mask;
+ u16 mask = E1000_SWFW_PHY0_SM;
+
+ if (hw->bus.func == E1000_FUNC_1)
+ mask = E1000_SWFW_PHY1_SM;
- mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM;
igb_release_swfw_sync_82575(hw, mask);
}
static s32 igb_read_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset,
u16 *data)
{
- struct e1000_phy_info *phy = &hw->phy;
- u32 i, i2ccmd = 0;
+ s32 ret_val = -E1000_ERR_PARAM;
if (offset > E1000_MAX_SGMII_PHY_REG_ADDR) {
hw_dbg("PHY Address %u is out of range\n", offset);
- return -E1000_ERR_PARAM;
+ goto out;
}
- /*
- * Set up Op-code, Phy Address, and register address in the I2CCMD
- * register. The MAC will take care of interfacing with the
- * PHY to retrieve the desired data.
- */
- i2ccmd = ((offset << E1000_I2CCMD_REG_ADDR_SHIFT) |
- (phy->addr << E1000_I2CCMD_PHY_ADDR_SHIFT) |
- (E1000_I2CCMD_OPCODE_READ));
-
- wr32(E1000_I2CCMD, i2ccmd);
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
- /* Poll the ready bit to see if the I2C read completed */
- for (i = 0; i < E1000_I2CCMD_PHY_TIMEOUT; i++) {
- udelay(50);
- i2ccmd = rd32(E1000_I2CCMD);
- if (i2ccmd & E1000_I2CCMD_READY)
- break;
- }
- if (!(i2ccmd & E1000_I2CCMD_READY)) {
- hw_dbg("I2CCMD Read did not complete\n");
- return -E1000_ERR_PHY;
- }
- if (i2ccmd & E1000_I2CCMD_ERROR) {
- hw_dbg("I2CCMD Error bit set\n");
- return -E1000_ERR_PHY;
- }
+ ret_val = igb_read_phy_reg_i2c(hw, offset, data);
- /* Need to byte-swap the 16-bit value. */
- *data = ((i2ccmd >> 8) & 0x00FF) | ((i2ccmd << 8) & 0xFF00);
+ hw->phy.ops.release(hw);
- return 0;
+out:
+ return ret_val;
}
/**
static s32 igb_write_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset,
u16 data)
{
- struct e1000_phy_info *phy = &hw->phy;
- u32 i, i2ccmd = 0;
- u16 phy_data_swapped;
+ s32 ret_val = -E1000_ERR_PARAM;
+
if (offset > E1000_MAX_SGMII_PHY_REG_ADDR) {
hw_dbg("PHY Address %d is out of range\n", offset);
- return -E1000_ERR_PARAM;
+ goto out;
}
- /* Swap the data bytes for the I2C interface */
- phy_data_swapped = ((data >> 8) & 0x00FF) | ((data << 8) & 0xFF00);
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
- /*
- * Set up Op-code, Phy Address, and register address in the I2CCMD
- * register. The MAC will take care of interfacing with the
- * PHY to retrieve the desired data.
- */
- i2ccmd = ((offset << E1000_I2CCMD_REG_ADDR_SHIFT) |
- (phy->addr << E1000_I2CCMD_PHY_ADDR_SHIFT) |
- E1000_I2CCMD_OPCODE_WRITE |
- phy_data_swapped);
-
- wr32(E1000_I2CCMD, i2ccmd);
-
- /* Poll the ready bit to see if the I2C read completed */
- for (i = 0; i < E1000_I2CCMD_PHY_TIMEOUT; i++) {
- udelay(50);
- i2ccmd = rd32(E1000_I2CCMD);
- if (i2ccmd & E1000_I2CCMD_READY)
- break;
- }
- if (!(i2ccmd & E1000_I2CCMD_READY)) {
- hw_dbg("I2CCMD Write did not complete\n");
- return -E1000_ERR_PHY;
- }
- if (i2ccmd & E1000_I2CCMD_ERROR) {
- hw_dbg("I2CCMD Error bit set\n");
- return -E1000_ERR_PHY;
- }
+ ret_val = igb_write_phy_reg_i2c(hw, offset, data);
- return 0;
+ hw->phy.ops.release(hw);
+
+out:
+ return ret_val;
}
/**
struct e1000_phy_info *phy = &hw->phy;
s32 ret_val = 0;
u16 phy_id;
+ u32 ctrl_ext;
/*
* For SGMII PHYs, we try the list of possible addresses until
goto out;
}
+ /* Power on sgmii phy if it is disabled */
+ ctrl_ext = rd32(E1000_CTRL_EXT);
+ wr32(E1000_CTRL_EXT, ctrl_ext & ~E1000_CTRL_EXT_SDP3_DATA);
+ wrfl();
+ msleep(300);
+
/*
* The address field in the I2CCMD register is 3 bits and 0 is invalid.
* Therefore, we need to test 1-7
phy->addr = 0;
ret_val = -E1000_ERR_PHY;
goto out;
+ } else {
+ ret_val = igb_get_phy_id(hw);
}
- ret_val = igb_get_phy_id(hw);
+ /* restore previous sfp cage power state */
+ wr32(E1000_CTRL_EXT, ctrl_ext);
out:
return ret_val;
s32 ret_val;
u16 speed, duplex;
- /* SGMII link check is done through the PCS register. */
- if ((hw->phy.media_type != e1000_media_type_copper) ||
- (igb_sgmii_active_82575(hw))) {
+ if (hw->phy.media_type != e1000_media_type_copper) {
ret_val = igb_get_pcs_speed_and_duplex_82575(hw, &speed,
&duplex);
/*
return ret_val;
}
+
/**
* igb_get_pcs_speed_and_duplex_82575 - Retrieve current speed/duplex
* @hw: pointer to the HW structure
}
/**
- * igb_shutdown_fiber_serdes_link_82575 - Remove link during power down
+ * igb_shutdown_serdes_link_82575 - Remove link during power down
* @hw: pointer to the HW structure
*
* In the case of fiber serdes, shut down optics and PCS on driver unload
* when management pass thru is not enabled.
**/
-void igb_shutdown_fiber_serdes_link_82575(struct e1000_hw *hw)
+void igb_shutdown_serdes_link_82575(struct e1000_hw *hw)
{
u32 reg;
+ u16 eeprom_data = 0;
- if (hw->phy.media_type != e1000_media_type_internal_serdes)
+ if (hw->phy.media_type != e1000_media_type_internal_serdes ||
+ igb_sgmii_active_82575(hw))
return;
- /* if the management interface is not enabled, then power down */
- if (!igb_enable_mng_pass_thru(hw)) {
+ if (hw->bus.func == E1000_FUNC_0)
+ hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A, 1, &eeprom_data);
+ else if (hw->bus.func == E1000_FUNC_1)
+ hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_B, 1, &eeprom_data);
+
+ /*
+ * If APM is not enabled in the EEPROM and management interface is
+ * not enabled, then power down.
+ */
+ if (!(eeprom_data & E1000_NVM_APME_82575) &&
+ !igb_enable_mng_pass_thru(hw)) {
/* Disable PCS to turn off link */
reg = rd32(E1000_PCS_CFG0);
reg &= ~E1000_PCS_CFG_PCS_EN;
/* shutdown the laser */
reg = rd32(E1000_CTRL_EXT);
- reg |= E1000_CTRL_EXT_SDP7_DATA;
+ reg |= E1000_CTRL_EXT_SDP3_DATA;
wr32(E1000_CTRL_EXT, reg);
/* flush the write to verify completion */
for (i = 0; i < mac->mta_reg_count; i++)
array_wr32(E1000_MTA, i, 0);
+ /* Zero out the Unicast HASH table */
+ hw_dbg("Zeroing the UTA\n");
+ for (i = 0; i < mac->uta_reg_count; i++)
+ array_wr32(E1000_UTA, i, 0);
+
/* Setup link and flow control */
ret_val = igb_setup_link(hw);
ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
wr32(E1000_CTRL, ctrl);
+ ret_val = igb_setup_serdes_link_82575(hw);
+ if (ret_val)
+ goto out;
+
+ if (igb_sgmii_active_82575(hw) && !hw->phy.reset_disable) {
+ ret_val = hw->phy.ops.reset(hw);
+ if (ret_val) {
+ hw_dbg("Error resetting the PHY.\n");
+ goto out;
+ }
+ }
switch (hw->phy.type) {
case e1000_phy_m88:
ret_val = igb_copper_link_setup_m88(hw);
}
}
- igb_configure_pcs_link_82575(hw);
-
/*
* Check link status. Wait up to 100 microseconds for link to become
* valid.
}
/**
- * igb_setup_fiber_serdes_link_82575 - Setup link for fiber/serdes
+ * igb_setup_serdes_link_82575 - Setup link for serdes
* @hw: pointer to the HW structure
*
- * Configures speed and duplex for fiber and serdes links.
+ * Configure the physical coding sub-layer (PCS) link. The PCS link is
+ * used on copper connections where the serialized gigabit media independent
+ * interface (sgmii), or serdes fiber is being used. Configures the link
+ * for auto-negotiation or forces speed/duplex.
**/
-static s32 igb_setup_fiber_serdes_link_82575(struct e1000_hw *hw)
+static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
{
- u32 reg;
+ u32 ctrl_reg, reg;
+
+ if ((hw->phy.media_type != e1000_media_type_internal_serdes) &&
+ !igb_sgmii_active_82575(hw))
+ return 0;
/*
* On the 82575, SerDes loopback mode persists until it is
*/
wr32(E1000_SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK);
- /* Force link up, set 1gb, set both sw defined pins */
- reg = rd32(E1000_CTRL);
- reg |= E1000_CTRL_SLU |
- E1000_CTRL_SPD_1000 |
- E1000_CTRL_FRCSPD |
- E1000_CTRL_SWDPIN0 |
- E1000_CTRL_SWDPIN1;
- wr32(E1000_CTRL, reg);
-
- /* Power on phy for 82576 fiber adapters */
- if (hw->mac.type == e1000_82576) {
- reg = rd32(E1000_CTRL_EXT);
- reg &= ~E1000_CTRL_EXT_SDP7_DATA;
- wr32(E1000_CTRL_EXT, reg);
+ /* power on the sfp cage if present */
+ reg = rd32(E1000_CTRL_EXT);
+ reg &= ~E1000_CTRL_EXT_SDP3_DATA;
+ wr32(E1000_CTRL_EXT, reg);
+
+ ctrl_reg = rd32(E1000_CTRL);
+ ctrl_reg |= E1000_CTRL_SLU;
+
+ if (hw->mac.type == e1000_82575 || hw->mac.type == e1000_82576) {
+ /* set both sw defined pins */
+ ctrl_reg |= E1000_CTRL_SWDPIN0 | E1000_CTRL_SWDPIN1;
+
+ /* Set switch control to serdes energy detect */
+ reg = rd32(E1000_CONNSW);
+ reg |= E1000_CONNSW_ENRGSRC;
+ wr32(E1000_CONNSW, reg);
}
- /* Set switch control to serdes energy detect */
- reg = rd32(E1000_CONNSW);
- reg |= E1000_CONNSW_ENRGSRC;
- wr32(E1000_CONNSW, reg);
+ reg = rd32(E1000_PCS_LCTL);
+
+ if (igb_sgmii_active_82575(hw)) {
+ /* allow time for SFP cage to power up phy */
+ msleep(300);
+
+ /* AN time out should be disabled for SGMII mode */
+ reg &= ~(E1000_PCS_LCTL_AN_TIMEOUT);
+ } else {
+ ctrl_reg |= E1000_CTRL_SPD_1000 | E1000_CTRL_FRCSPD |
+ E1000_CTRL_FD | E1000_CTRL_FRCDPX;
+ }
+
+ wr32(E1000_CTRL, ctrl_reg);
/*
* New SerDes mode allows for forcing speed or autonegotiating speed
* mode that will be compatible with older link partners and switches.
* However, both are supported by the hardware and some drivers/tools.
*/
- reg = rd32(E1000_PCS_LCTL);
reg &= ~(E1000_PCS_LCTL_AN_ENABLE | E1000_PCS_LCTL_FLV_LINK_UP |
E1000_PCS_LCTL_FSD | E1000_PCS_LCTL_FORCE_LINK);
- if (hw->mac.autoneg) {
+ /*
+ * We force flow control to prevent the CTRL register values from being
+ * overwritten by the autonegotiated flow control values
+ */
+ reg |= E1000_PCS_LCTL_FORCE_FCTRL;
+
+ /*
+ * we always set sgmii to autoneg since it is the phy that will be
+ * forcing the link and the serdes is just a go-between
+ */
+ if (hw->mac.autoneg || igb_sgmii_active_82575(hw)) {
/* Set PCS register for autoneg */
- reg |= E1000_PCS_LCTL_FSV_1000 | /* Force 1000 */
- E1000_PCS_LCTL_FDV_FULL | /* SerDes Full duplex */
- E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */
- E1000_PCS_LCTL_AN_RESTART; /* Restart autoneg */
+ reg |= E1000_PCS_LCTL_FSV_1000 | /* Force 1000 */
+ E1000_PCS_LCTL_FDV_FULL | /* SerDes Full dplx */
+ E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */
+ E1000_PCS_LCTL_AN_RESTART; /* Restart autoneg */
hw_dbg("Configuring Autoneg; PCS_LCTL = 0x%08X\n", reg);
} else {
- /* Set PCS register for forced speed */
- reg |= E1000_PCS_LCTL_FLV_LINK_UP | /* Force link up */
- E1000_PCS_LCTL_FSV_1000 | /* Force 1000 */
- E1000_PCS_LCTL_FDV_FULL | /* SerDes Full duplex */
- E1000_PCS_LCTL_FSD | /* Force Speed */
- E1000_PCS_LCTL_FORCE_LINK; /* Force Link */
- hw_dbg("Configuring Forced Link; PCS_LCTL = 0x%08X\n", reg);
- }
-
- if (hw->mac.type == e1000_82576) {
- reg |= E1000_PCS_LCTL_FORCE_FCTRL;
- igb_force_mac_fc(hw);
- }
-
- wr32(E1000_PCS_LCTL, reg);
-
- return 0;
-}
-
-/**
- * igb_configure_pcs_link_82575 - Configure PCS link
- * @hw: pointer to the HW structure
- *
- * Configure the physical coding sub-layer (PCS) link. The PCS link is
- * only used on copper connections where the serialized gigabit media
- * independent interface (sgmii) is being used. Configures the link
- * for auto-negotiation or forces speed/duplex.
- **/
-static void igb_configure_pcs_link_82575(struct e1000_hw *hw)
-{
- struct e1000_mac_info *mac = &hw->mac;
- u32 reg = 0;
-
- if (hw->phy.media_type != e1000_media_type_copper ||
- !(igb_sgmii_active_82575(hw)))
- return;
-
- /* For SGMII, we need to issue a PCS autoneg restart */
- reg = rd32(E1000_PCS_LCTL);
-
- /* AN time out should be disabled for SGMII mode */
- reg &= ~(E1000_PCS_LCTL_AN_TIMEOUT);
-
- if (mac->autoneg) {
- /* Make sure forced speed and force link are not set */
- reg &= ~(E1000_PCS_LCTL_FSD | E1000_PCS_LCTL_FORCE_LINK);
-
- /*
- * The PHY should be setup prior to calling this function.
- * All we need to do is restart autoneg and enable autoneg.
- */
- reg |= E1000_PCS_LCTL_AN_RESTART | E1000_PCS_LCTL_AN_ENABLE;
- } else {
- /* Set PCS register for forced speed */
-
- /* Turn off bits for full duplex, speed, and autoneg */
- reg &= ~(E1000_PCS_LCTL_FSV_1000 |
- E1000_PCS_LCTL_FSV_100 |
- E1000_PCS_LCTL_FDV_FULL |
- E1000_PCS_LCTL_AN_ENABLE);
-
/* Check for duplex first */
- if (mac->forced_speed_duplex & E1000_ALL_FULL_DUPLEX)
+ if (hw->mac.forced_speed_duplex & E1000_ALL_FULL_DUPLEX)
reg |= E1000_PCS_LCTL_FDV_FULL;
+ /* No need to check for 1000/full since the spec states that
+ * it requires autoneg to be enabled */
/* Now set speed */
- if (mac->forced_speed_duplex & E1000_ALL_100_SPEED)
+ if (hw->mac.forced_speed_duplex & E1000_ALL_100_SPEED)
reg |= E1000_PCS_LCTL_FSV_100;
/* Force speed and force link */
E1000_PCS_LCTL_FORCE_LINK |
E1000_PCS_LCTL_FLV_LINK_UP;
- hw_dbg("Wrote 0x%08X to PCS_LCTL to configure forced link\n",
- reg);
+ hw_dbg("Configuring Forced Link; PCS_LCTL = 0x%08X\n", reg);
}
+
wr32(E1000_PCS_LCTL, reg);
+
+ if (!igb_sgmii_active_82575(hw))
+ igb_force_mac_fc(hw);
+
+ return 0;
}
/**
**/
static void igb_clear_hw_cntrs_82575(struct e1000_hw *hw)
{
- u32 temp;
-
igb_clear_hw_cntrs_base(hw);
- temp = rd32(E1000_PRC64);
- temp = rd32(E1000_PRC127);
- temp = rd32(E1000_PRC255);
- temp = rd32(E1000_PRC511);
- temp = rd32(E1000_PRC1023);
- temp = rd32(E1000_PRC1522);
- temp = rd32(E1000_PTC64);
- temp = rd32(E1000_PTC127);
- temp = rd32(E1000_PTC255);
- temp = rd32(E1000_PTC511);
- temp = rd32(E1000_PTC1023);
- temp = rd32(E1000_PTC1522);
-
- temp = rd32(E1000_ALGNERRC);
- temp = rd32(E1000_RXERRC);
- temp = rd32(E1000_TNCRS);
- temp = rd32(E1000_CEXTERR);
- temp = rd32(E1000_TSCTC);
- temp = rd32(E1000_TSCTFC);
-
- temp = rd32(E1000_MGTPRC);
- temp = rd32(E1000_MGTPDC);
- temp = rd32(E1000_MGTPTC);
-
- temp = rd32(E1000_IAC);
- temp = rd32(E1000_ICRXOC);
-
- temp = rd32(E1000_ICRXPTC);
- temp = rd32(E1000_ICRXATC);
- temp = rd32(E1000_ICTXPTC);
- temp = rd32(E1000_ICTXATC);
- temp = rd32(E1000_ICTXQEC);
- temp = rd32(E1000_ICTXQMTC);
- temp = rd32(E1000_ICRXDMTC);
-
- temp = rd32(E1000_CBTMPC);
- temp = rd32(E1000_HTDPMC);
- temp = rd32(E1000_CBRMPC);
- temp = rd32(E1000_RPTHC);
- temp = rd32(E1000_HGPTC);
- temp = rd32(E1000_HTCBDPC);
- temp = rd32(E1000_HGORCL);
- temp = rd32(E1000_HGORCH);
- temp = rd32(E1000_HGOTCL);
- temp = rd32(E1000_HGOTCH);
- temp = rd32(E1000_LENERRS);
+ rd32(E1000_PRC64);
+ rd32(E1000_PRC127);
+ rd32(E1000_PRC255);
+ rd32(E1000_PRC511);
+ rd32(E1000_PRC1023);
+ rd32(E1000_PRC1522);
+ rd32(E1000_PTC64);
+ rd32(E1000_PTC127);
+ rd32(E1000_PTC255);
+ rd32(E1000_PTC511);
+ rd32(E1000_PTC1023);
+ rd32(E1000_PTC1522);
+
+ rd32(E1000_ALGNERRC);
+ rd32(E1000_RXERRC);
+ rd32(E1000_TNCRS);
+ rd32(E1000_CEXTERR);
+ rd32(E1000_TSCTC);
+ rd32(E1000_TSCTFC);
+
+ rd32(E1000_MGTPRC);
+ rd32(E1000_MGTPDC);
+ rd32(E1000_MGTPTC);
+
+ rd32(E1000_IAC);
+ rd32(E1000_ICRXOC);
+
+ rd32(E1000_ICRXPTC);
+ rd32(E1000_ICRXATC);
+ rd32(E1000_ICTXPTC);
+ rd32(E1000_ICTXATC);
+ rd32(E1000_ICTXQEC);
+ rd32(E1000_ICTXQMTC);
+ rd32(E1000_ICRXDMTC);
+
+ rd32(E1000_CBTMPC);
+ rd32(E1000_HTDPMC);
+ rd32(E1000_CBRMPC);
+ rd32(E1000_RPTHC);
+ rd32(E1000_HGPTC);
+ rd32(E1000_HTCBDPC);
+ rd32(E1000_HGORCL);
+ rd32(E1000_HGORCH);
+ rd32(E1000_HGOTCL);
+ rd32(E1000_HGOTCH);
+ rd32(E1000_LENERRS);
/* This register should not be read in copper configurations */
- if (hw->phy.media_type == e1000_media_type_internal_serdes)
- temp = rd32(E1000_SCVPC);
+ if (hw->phy.media_type == e1000_media_type_internal_serdes ||
+ igb_sgmii_active_82575(hw))
+ rd32(E1000_SCVPC);
}
/**
projects / deliverable / linux.git / blobdiff