/*******************************************************************************
Intel(R) Gigabit Ethernet Linux driver
- Copyright(c) 2007 - 2008 Intel Corporation.
+ Copyright(c) 2007-2009 Intel Corporation.
This program is free software; you can redistribute it and/or modify it
under the terms and conditions of the GNU General Public License,
#define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */
#define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */
#define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */
-#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */
-#define E1000_WUFC_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Enable */
-#define E1000_WUFC_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Enable */
-#define E1000_WUFC_FLX0 0x00010000 /* Flexible Filter 0 Enable */
-#define E1000_WUFC_FLX1 0x00020000 /* Flexible Filter 1 Enable */
-#define E1000_WUFC_FLX2 0x00040000 /* Flexible Filter 2 Enable */
-#define E1000_WUFC_FLX3 0x00080000 /* Flexible Filter 3 Enable */
-#define E1000_WUFC_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */
-
-/* Wake Up Status */
-
-/* Wake Up Packet Length */
-
-/* Four Flexible Filters are supported */
-#define E1000_FLEXIBLE_FILTER_COUNT_MAX 4
-
-/* Each Flexible Filter is at most 128 (0x80) bytes in length */
-#define E1000_FLEXIBLE_FILTER_SIZE_MAX 128
-
/* Extended Device Control */
-#define E1000_CTRL_EXT_GPI1_EN 0x00000002 /* Maps SDP5 to GPI1 */
-#define E1000_CTRL_EXT_SDP4_DATA 0x00000010 /* Value of SW Defineable Pin 4 */
-#define E1000_CTRL_EXT_SDP5_DATA 0x00000020 /* Value of SW Defineable Pin 5 */
#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Defineable Pin 7 */
-#define E1000_CTRL_EXT_SDP4_DIR 0x00000100 /* Direction of SDP4 0=in 1=out */
-#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
+/* Physical Func Reset Done Indication */
+#define E1000_CTRL_EXT_PFRSTD 0x00004000
#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
#define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES 0x00C00000
#define E1000_CTRL_EXT_LINK_MODE_SGMII 0x00800000
#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */
#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */
#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */
-#define E1000_RXD_STAT_DYNINT 0x800 /* Pkt caused INT via DYNINT */
-#define E1000_RXD_ERR_CE 0x01 /* CRC Error */
-#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */
-#define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */
-#define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */
-#define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */
-#define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */
+#define E1000_RXD_STAT_TS 0x10000 /* Pkt was time stamped */
#define E1000_RXDEXT_STATERR_CE 0x01000000
#define E1000_RXDEXT_STATERR_SE 0x02000000
#define E1000_RXDEXT_STATERR_IPE 0x40000000
#define E1000_RXDEXT_STATERR_RXE 0x80000000
-/* mask to determine if packets should be dropped due to frame errors */
-#define E1000_RXD_ERR_FRAME_ERR_MASK ( \
- E1000_RXD_ERR_CE | \
- E1000_RXD_ERR_SE | \
- E1000_RXD_ERR_SEQ | \
- E1000_RXD_ERR_CXE | \
- E1000_RXD_ERR_RXE)
-
/* Same mask, but for extended and packet split descriptors */
#define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \
E1000_RXDEXT_STATERR_CE | \
/* Management Control */
#define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */
#define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */
-#define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */
/* Enable Neighbor Discovery Filtering */
#define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */
#define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */
/* Enable MAC address filtering */
#define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000
-/* Enable MNG packets to host memory */
-#define E1000_MANC_EN_MNG2HOST 0x00200000
-/* Enable IP address filtering */
-
/* Receive Control */
#define E1000_RCTL_EN 0x00000002 /* enable */
#define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */
#define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */
#define E1000_RCTL_LPE 0x00000020 /* long packet enable */
-#define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */
#define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */
#define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */
#define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min threshold size */
#define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */
#define E1000_RCTL_BAM 0x00008000 /* broadcast enable */
-#define E1000_RCTL_SZ_2048 0x00000000 /* rx buffer size 2048 */
-#define E1000_RCTL_SZ_1024 0x00010000 /* rx buffer size 1024 */
#define E1000_RCTL_SZ_512 0x00020000 /* rx buffer size 512 */
#define E1000_RCTL_SZ_256 0x00030000 /* rx buffer size 256 */
#define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */
/* enable link status from external LINK_0 and LINK_1 pins */
#define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */
#define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */
-#define E1000_CTRL_SWDPIN2 0x00100000 /* SWDPIN 2 value */
-#define E1000_CTRL_SWDPIN3 0x00200000 /* SWDPIN 3 value */
#define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */
-#define E1000_CTRL_SWDPIO2 0x01000000 /* SWDPIN 2 input or output */
-#define E1000_CTRL_SWDPIO3 0x02000000 /* SWDPIN 3 input or output */
#define E1000_CTRL_RST 0x04000000 /* Global reset */
#define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */
#define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */
#define AUTONEG_ADVERTISE_SPEED_DEFAULT E1000_ALL_SPEED_DUPLEX
/* LED Control */
-#define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F
#define E1000_LEDCTL_LED0_MODE_SHIFT 0
-#define E1000_LEDCTL_LED0_IVRT 0x00000040
#define E1000_LEDCTL_LED0_BLINK 0x00000080
#define E1000_LEDCTL_MODE_LED_ON 0xE
#define E1000_SCTL_DISABLE_SERDES_LOOPBACK 0x0400
/* Receive Checksum Control */
+#define E1000_RXCSUM_IPOFL 0x00000100 /* IPv4 checksum offload */
#define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */
-#define E1000_RXCSUM_IPPCSE 0x00001000 /* IP payload checksum enable */
#define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */
/* Header split receive */
#define MAX_JUMBO_FRAME_SIZE 0x3F00
-/* Extended Configuration Control and Size */
-#define E1000_PHY_CTRL_GBE_DISABLE 0x00000040
-
/* PBA constants */
-#define E1000_PBA_16K 0x0010 /* 16KB, default TX allocation */
-#define E1000_PBA_24K 0x0018
#define E1000_PBA_34K 0x0022
#define E1000_PBA_64K 0x0040 /* 64KB */
/* Interrupt Cause Read */
#define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */
-#define E1000_ICR_TXQE 0x00000002 /* Transmit Queue empty */
#define E1000_ICR_LSC 0x00000004 /* Link Status Change */
#define E1000_ICR_RXSEQ 0x00000008 /* rx sequence error */
#define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */
-#define E1000_ICR_RXO 0x00000040 /* rx overrun */
#define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */
-#define E1000_ICR_MDAC 0x00000200 /* MDIO access complete */
-#define E1000_ICR_RXCFG 0x00000400 /* Rx /c/ ordered set */
-#define E1000_ICR_GPI_EN0 0x00000800 /* GP Int 0 */
-#define E1000_ICR_GPI_EN1 0x00001000 /* GP Int 1 */
-#define E1000_ICR_GPI_EN2 0x00002000 /* GP Int 2 */
-#define E1000_ICR_GPI_EN3 0x00004000 /* GP Int 3 */
-#define E1000_ICR_TXD_LOW 0x00008000
-#define E1000_ICR_SRPD 0x00010000
-#define E1000_ICR_ACK 0x00020000 /* Receive Ack frame */
-#define E1000_ICR_MNG 0x00040000 /* Manageability event */
-#define E1000_ICR_DOCK 0x00080000 /* Dock/Undock */
+#define E1000_ICR_VMMB 0x00000100 /* VM MB event */
/* If this bit asserted, the driver should claim the interrupt */
#define E1000_ICR_INT_ASSERTED 0x80000000
-/* queue 0 Rx descriptor FIFO parity error */
-#define E1000_ICR_RXD_FIFO_PAR0 0x00100000
-/* queue 0 Tx descriptor FIFO parity error */
-#define E1000_ICR_TXD_FIFO_PAR0 0x00200000
-/* host arb read buffer parity error */
-#define E1000_ICR_HOST_ARB_PAR 0x00400000
-#define E1000_ICR_PB_PAR 0x00800000 /* packet buffer parity error */
-/* queue 1 Rx descriptor FIFO parity error */
-#define E1000_ICR_RXD_FIFO_PAR1 0x01000000
-/* queue 1 Tx descriptor FIFO parity error */
-#define E1000_ICR_TXD_FIFO_PAR1 0x02000000
-/* FW changed the status of DISSW bit in the FWSM */
-#define E1000_ICR_DSW 0x00000020
/* LAN connected device generates an interrupt */
-#define E1000_ICR_PHYINT 0x00001000
-#define E1000_ICR_EPRST 0x00100000 /* ME handware reset occurs */
+#define E1000_ICR_DOUTSYNC 0x10000000 /* NIC DMA out of sync */
/* Extended Interrupt Cause Read */
#define E1000_EICR_RX_QUEUE0 0x00000001 /* Rx Queue 0 Interrupt */
#define E1000_EICR_TX_QUEUE1 0x00000200 /* Tx Queue 1 Interrupt */
#define E1000_EICR_TX_QUEUE2 0x00000400 /* Tx Queue 2 Interrupt */
#define E1000_EICR_TX_QUEUE3 0x00000800 /* Tx Queue 3 Interrupt */
-#define E1000_EICR_TCP_TIMER 0x40000000 /* TCP Timer */
#define E1000_EICR_OTHER 0x80000000 /* Interrupt Cause Active */
/* TCP Timer */
E1000_IMS_TXDW | \
E1000_IMS_RXDMT0 | \
E1000_IMS_RXSEQ | \
- E1000_IMS_LSC)
+ E1000_IMS_LSC | \
+ E1000_IMS_DOUTSYNC)
/* Interrupt Mask Set */
#define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
#define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */
+#define E1000_IMS_VMMB E1000_ICR_VMMB /* Mail box activity */
#define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
#define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
#define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
+#define E1000_IMS_DOUTSYNC E1000_ICR_DOUTSYNC /* NIC DMA out of sync */
/* Extended Interrupt Mask Set */
-#define E1000_EIMS_TCP_TIMER E1000_EICR_TCP_TIMER /* TCP Timer */
#define E1000_EIMS_OTHER E1000_EICR_OTHER /* Interrupt Cause Active */
/* Interrupt Cause Set */
* manageability enabled, allowing us room for 15 multicast addresses.
*/
#define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */
+#define E1000_RAL_MAC_ADDR_LEN 4
+#define E1000_RAH_MAC_ADDR_LEN 2
+#define E1000_RAH_POOL_MASK 0x03FC0000
+#define E1000_RAH_POOL_1 0x00040000
/* Error Codes */
#define E1000_ERR_NVM 1
#define E1000_ERR_MAC_INIT 5
#define E1000_ERR_RESET 9
#define E1000_ERR_MASTER_REQUESTS_PENDING 10
-#define E1000_ERR_HOST_INTERFACE_COMMAND 11
#define E1000_BLK_PHY_RESET 12
#define E1000_ERR_SWFW_SYNC 13
#define E1000_NOT_IMPLEMENTED 14
+#define E1000_ERR_MBX 15
/* Loop limit on how long we wait for auto-negotiation to complete */
#define COPPER_LINK_UP_LIMIT 10
/* Flow Control */
#define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */
-/* Transmit Configuration Word */
-#define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */
-
-/* Receive Configuration Word */
-
-/* PCI Express Control */
-#define E1000_GCR_RXD_NO_SNOOP 0x00000001
-#define E1000_GCR_RXDSCW_NO_SNOOP 0x00000002
-#define E1000_GCR_RXDSCR_NO_SNOOP 0x00000004
-#define E1000_GCR_TXD_NO_SNOOP 0x00000008
-#define E1000_GCR_TXDSCW_NO_SNOOP 0x00000010
-#define E1000_GCR_TXDSCR_NO_SNOOP 0x00000020
-
-#define PCIE_NO_SNOOP_ALL (E1000_GCR_RXD_NO_SNOOP | \
- E1000_GCR_RXDSCW_NO_SNOOP | \
- E1000_GCR_RXDSCR_NO_SNOOP | \
- E1000_GCR_TXD_NO_SNOOP | \
- E1000_GCR_TXDSCW_NO_SNOOP | \
- E1000_GCR_TXDSCR_NO_SNOOP)
-
/* PHY Control Register */
#define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */
#define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */
-#define MII_CR_POWER_DOWN 0x0800 /* Power down */
#define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */
#define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */
#define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */
#define NVM_ID_LED_SETTINGS 0x0004
/* For SERDES output amplitude adjustment. */
#define NVM_INIT_CONTROL2_REG 0x000F
+#define NVM_INIT_CONTROL3_PORT_B 0x0014
#define NVM_INIT_CONTROL3_PORT_A 0x0024
#define NVM_ALT_MAC_ADDR_PTR 0x0037
#define NVM_CHECKSUM_REG 0x003F
#define IGP_LED3_MODE 0x07000000
/* PCI/PCI-X/PCI-EX Config space */
-#define PCI_HEADER_TYPE_REGISTER 0x0E
#define PCIE_LINK_STATUS 0x12
-#define PCI_HEADER_TYPE_MULTIFUNC 0x80
#define PCIE_LINK_WIDTH_MASK 0x3F0
#define PCIE_LINK_WIDTH_SHIFT 4
#define E1000_GEN_CTL_ADDRESS_SHIFT 8
#define E1000_GEN_POLL_TIMEOUT 640
+#define E1000_VFTA_ENTRY_SHIFT 5
+#define E1000_VFTA_ENTRY_MASK 0x7F
+#define E1000_VFTA_ENTRY_BIT_SHIFT_MASK 0x1F
+
#endif
projects / deliverable / linux.git / blobdiff