ixgb: fix spelling errors

[deliverable/linux.git] / drivers / net / ixgb / ixgb_hw.c

diff --git a/drivers/net/ixgb/ixgb_hw.c b/drivers/net/ixgb/ixgb_hw.c
index 04d2003e24e12a789ac9805d17c61ae716729ef1..3694e8c7b00517dafd5f6c8b940ba1af14b3891f 100644 (file)
--- a/drivers/net/ixgb/ixgb_hw.c
+++ b/drivers/net/ixgb/ixgb_hw.c
@@ -125,7 +125,7 @@ ixgb_adapter_stop(struct ixgb_hw *hw)
        /* If we are stopped or resetting exit gracefully and wait to be
         * started again before accessing the hardware.
         */
-       if(hw->adapter_stopped) {
+       if (hw->adapter_stopped) {
                DEBUGOUT("Exiting because the adapter is already stopped!!!\n");
                return false;
        }
@@ -371,7 +371,7 @@ ixgb_init_hw(struct ixgb_hw *hw)
  * hw - Struct containing variables accessed by shared code
  *
  * Places the MAC address in receive address register 0 and clears the rest
- * of the receive addresss registers. Clears the multicast table. Assumes
+ * of the receive address registers. Clears the multicast table. Assumes
  * the receiver is in reset when the routine is called.
  *****************************************************************************/
 static void
@@ -482,7 +482,7 @@ ixgb_mc_addr_list_update(struct ixgb_hw *hw,
                /* Place this multicast address in the RAR if there is room, *
                 * else put it in the MTA
                 */
-               if(rar_used_count < IXGB_RAR_ENTRIES) {
+               if (rar_used_count < IXGB_RAR_ENTRIES) {
                        ixgb_rar_set(hw,
                                     mc_addr_list +
                                     (i * (IXGB_ETH_LENGTH_OF_ADDRESS + pad)),
@@ -719,9 +719,8 @@ ixgb_setup_fc(struct ixgb_hw *hw)
        /* Write the new settings */
        IXGB_WRITE_REG(hw, CTRL0, ctrl_reg);
 
-       if (pap_reg != 0) {
+       if (pap_reg != 0)
                IXGB_WRITE_REG(hw, PAP, pap_reg);
-       }
 
        /* Set the flow control receive threshold registers.  Normally,
         * these registers will be set to a default threshold that may be
@@ -729,14 +728,14 @@ ixgb_setup_fc(struct ixgb_hw *hw)
         * ability to transmit pause frames in not enabled, then these
         * registers will be set to 0.
         */
-       if(!(hw->fc.type & ixgb_fc_tx_pause)) {
+       if (!(hw->fc.type & ixgb_fc_tx_pause)) {
                IXGB_WRITE_REG(hw, FCRTL, 0);
                IXGB_WRITE_REG(hw, FCRTH, 0);
        } else {
           /* We need to set up the Receive Threshold high and low water
            * marks as well as (optionally) enabling the transmission of XON
            * frames. */
-               if(hw->fc.send_xon) {
+               if (hw->fc.send_xon) {
                        IXGB_WRITE_REG(hw, FCRTL,
                                (hw->fc.low_water | IXGB_FCRTL_XONE));
                } else {
@@ -965,7 +964,7 @@ ixgb_check_for_link(struct ixgb_hw *hw)
 }
 
 /******************************************************************************
- * Check for a bad link condition that may have occured.
+ * Check for a bad link condition that may have occurred.
  * The indication is that the RFC / LFC registers may be incrementing
  * continually.  A full adapter reset is required to recover.
  *
@@ -1007,7 +1006,7 @@ ixgb_clear_hw_cntrs(struct ixgb_hw *hw)
        DEBUGFUNC("ixgb_clear_hw_cntrs");
 
        /* if we are stopped or resetting exit gracefully */
-       if(hw->adapter_stopped) {
+       if (hw->adapter_stopped) {
                DEBUGOUT("Exiting because the adapter is stopped!!!\n");
                return;
        }