u32 rmcs_reg;
u32 reg;
+#ifdef CONFIG_DCB
+ if (hw->fc.requested_mode == ixgbe_fc_pfc)
+ goto out;
+
+#endif /* CONFIG_DCB */
+ /* Negotiate the fc mode to use */
+ ret_val = ixgbe_fc_autoneg(hw);
+ if (ret_val)
+ goto out;
+
+ /* Disable any previous flow control settings */
fctrl_reg = IXGBE_READ_REG(hw, IXGBE_FCTRL);
fctrl_reg &= ~(IXGBE_FCTRL_RFCE | IXGBE_FCTRL_RPFCE);
* 0: Flow control is completely disabled
* 1: Rx flow control is enabled (we can receive pause frames,
* but not send pause frames).
- * 2: Tx flow control is enabled (we can send pause frames but
+ * 2: Tx flow control is enabled (we can send pause frames but
* we do not support receiving pause frames).
* 3: Both Rx and Tx flow control (symmetric) are enabled.
* other: Invalid.
+#ifdef CONFIG_DCB
+ * 4: Priority Flow Control is enabled.
+#endif
*/
switch (hw->fc.current_mode) {
case ixgbe_fc_none:
- /* Flow control completely disabled by software override. */
+ /*
+ * Flow control is disabled by software override or autoneg.
+ * The code below will actually disable it in the HW.
+ */
break;
case ixgbe_fc_rx_pause:
/*
fctrl_reg |= IXGBE_FCTRL_RFCE;
rmcs_reg |= IXGBE_RMCS_TFCE_802_3X;
break;
+#ifdef CONFIG_DCB
+ case ixgbe_fc_pfc:
+ goto out;
+ break;
+#endif /* CONFIG_DCB */
default:
hw_dbg(hw, "Flow control param set incorrectly\n");
ret_val = -IXGBE_ERR_CONFIG;
break;
}
- /* Enable 802.3x based flow control settings. */
+ /* Set 802.3x based flow control settings. */
fctrl_reg |= IXGBE_FCTRL_DPF;
IXGBE_WRITE_REG(hw, IXGBE_FCTRL, fctrl_reg);
IXGBE_WRITE_REG(hw, IXGBE_RMCS, rmcs_reg);
return ret_val;
}
-/**
- * ixgbe_setup_fc_82598 - Configure flow control settings
- * @hw: pointer to hardware structure
- * @packetbuf_num: packet buffer number (0-7)
- *
- * Configures the flow control settings based on SW configuration. This
- * function is used for 802.3x flow control configuration only.
- **/
-static s32 ixgbe_setup_fc_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
-{
- s32 ret_val = 0;
- ixgbe_link_speed speed;
- bool link_up;
-
- /* Validate the packetbuf configuration */
- if (packetbuf_num < 0 || packetbuf_num > 7) {
- hw_dbg(hw, "Invalid packet buffer number [%d], expected range is"
- " 0-7\n", packetbuf_num);
- ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
- goto out;
- }
-
- /*
- * Validate the water mark configuration. Zero water marks are invalid
- * because it causes the controller to just blast out fc packets.
- */
- if (!hw->fc.low_water || !hw->fc.high_water || !hw->fc.pause_time) {
- if (hw->fc.requested_mode != ixgbe_fc_none) {
- hw_dbg(hw, "Invalid water mark configuration\n");
- ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
- goto out;
- }
- }
-
- /*
- * Validate the requested mode. Strict IEEE mode does not allow
- * ixgbe_fc_rx_pause because it will cause testing anomalies.
- */
- if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
- hw_dbg(hw, "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
- ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
- goto out;
- }
-
- /*
- * 10gig parts do not have a word in the EEPROM to determine the
- * default flow control setting, so we explicitly set it to full.
- */
- if (hw->fc.requested_mode == ixgbe_fc_default)
- hw->fc.requested_mode = ixgbe_fc_full;
-
- /*
- * Save off the requested flow control mode for use later. Depending
- * on the link partner's capabilities, we may or may not use this mode.
- */
-
- hw->fc.current_mode = hw->fc.requested_mode;
-
- /* Decide whether to use autoneg or not. */
- hw->mac.ops.check_link(hw, &speed, &link_up, false);
- if (!hw->fc.disable_fc_autoneg && hw->phy.multispeed_fiber &&
- (speed == IXGBE_LINK_SPEED_1GB_FULL))
- ret_val = ixgbe_fc_autoneg(hw);
-
- if (ret_val)
- goto out;
-
- ret_val = ixgbe_fc_enable_82598(hw, packetbuf_num);
-
-out:
- return ret_val;
-}
-
/**
* ixgbe_setup_mac_link_82598 - Configures MAC link settings
* @hw: pointer to hardware structure
}
}
- /*
- * We want to save off the original Flow Control configuration just in
- * case we get disconnected and then reconnected into a different hub
- * or switch with different Flow Control capabilities.
- */
- ixgbe_setup_fc_82598(hw, 0);
-
/* Add delay to filter out noises during initial link setup */
msleep(50);
else
*speed = IXGBE_LINK_SPEED_1GB_FULL;
+ /* if link is down, zero out the current_mode */
+ if (*link_up == false) {
+ hw->fc.current_mode = ixgbe_fc_none;
+ hw->fc.fc_was_autonegged = false;
+ }
out:
return 0;
}
.disable_mc = &ixgbe_disable_mc_generic,
.clear_vfta = &ixgbe_clear_vfta_82598,
.set_vfta = &ixgbe_set_vfta_82598,
- .setup_fc = &ixgbe_setup_fc_82598,
+ .fc_enable = &ixgbe_fc_enable_82598,
};
static struct ixgbe_eeprom_operations eeprom_ops_82598 = {
projects / deliverable / linux.git / blobdiff