#include <linux/mmc/card.h>
#include <linux/semaphore.h>
#include <linux/firmware.h>
+#include <linux/module.h>
#include <asm/unaligned.h>
#include <defs.h>
#include <brcmu_wifi.h>
#include <brcm_hw_ids.h>
#include <soc.h>
#include "sdio_host.h"
+#include "sdio_chip.h"
#define DCMD_RESP_TIMEOUT 2000 /* In milli second */
/* Force no backplane reset */
#define SBSDIO_DEVCTL_RST_NOBPRESET 0x20
-/* SBSDIO_FUNC1_CHIPCLKCSR */
-
-/* Force ALP request to backplane */
-#define SBSDIO_FORCE_ALP 0x01
-/* Force HT request to backplane */
-#define SBSDIO_FORCE_HT 0x02
-/* Force ILP request to backplane */
-#define SBSDIO_FORCE_ILP 0x04
-/* Make ALP ready (power up xtal) */
-#define SBSDIO_ALP_AVAIL_REQ 0x08
-/* Make HT ready (power up PLL) */
-#define SBSDIO_HT_AVAIL_REQ 0x10
-/* Squelch clock requests from HW */
-#define SBSDIO_FORCE_HW_CLKREQ_OFF 0x20
-/* Status: ALP is ready */
-#define SBSDIO_ALP_AVAIL 0x40
-/* Status: HT is ready */
-#define SBSDIO_HT_AVAIL 0x80
-
-#define SBSDIO_AVBITS (SBSDIO_HT_AVAIL | SBSDIO_ALP_AVAIL)
-#define SBSDIO_ALPAV(regval) ((regval) & SBSDIO_AVBITS)
-#define SBSDIO_HTAV(regval) (((regval) & SBSDIO_AVBITS) == SBSDIO_AVBITS)
-#define SBSDIO_ALPONLY(regval) (SBSDIO_ALPAV(regval) && !SBSDIO_HTAV(regval))
-
-#define SBSDIO_CLKAV(regval, alponly) \
- (SBSDIO_ALPAV(regval) && (alponly ? 1 : SBSDIO_HTAV(regval)))
-
/* direct(mapped) cis space */
/* MAPPED common CIS address */
/* Flags for SDH calls */
#define F2SYNC (SDIO_REQ_4BYTE | SDIO_REQ_FIXED)
-/* sbimstate */
-#define SBIM_IBE 0x20000 /* inbanderror */
-#define SBIM_TO 0x40000 /* timeout */
-#define SBIM_BY 0x01800000 /* busy (sonics >= 2.3) */
-#define SBIM_RJ 0x02000000 /* reject (sonics >= 2.3) */
-
-/* sbtmstatelow */
-
-/* reset */
-#define SBTML_RESET 0x0001
-/* reject field */
-#define SBTML_REJ_MASK 0x0006
-/* reject */
-#define SBTML_REJ 0x0002
-/* temporary reject, for error recovery */
-#define SBTML_TMPREJ 0x0004
-
-/* Shift to locate the SI control flags in sbtml */
-#define SBTML_SICF_SHIFT 16
-
-/* sbtmstatehigh */
-#define SBTMH_SERR 0x0001 /* serror */
-#define SBTMH_INT 0x0002 /* interrupt */
-#define SBTMH_BUSY 0x0004 /* busy */
-#define SBTMH_TO 0x0020 /* timeout (sonics >= 2.3) */
-
-/* Shift to locate the SI status flags in sbtmh */
-#define SBTMH_SISF_SHIFT 16
-
-/* sbidlow */
-#define SBIDL_INIT 0x80 /* initiator */
-
-/* sbidhigh */
-#define SBIDH_RC_MASK 0x000f /* revision code */
-#define SBIDH_RCE_MASK 0x7000 /* revision code extension field */
-#define SBIDH_RCE_SHIFT 8
-#define SBCOREREV(sbidh) \
- ((((sbidh) & SBIDH_RCE_MASK) >> SBIDH_RCE_SHIFT) | \
- ((sbidh) & SBIDH_RC_MASK))
-#define SBIDH_CC_MASK 0x8ff0 /* core code */
-#define SBIDH_CC_SHIFT 4
-#define SBIDH_VC_MASK 0xffff0000 /* vendor code */
-#define SBIDH_VC_SHIFT 16
-
/*
* Conversion of 802.1D priority to precedence level
*/
(prio^2) : prio;
}
-/*
- * Core reg address translation.
- * Both macro's returns a 32 bits byte address on the backplane bus.
- */
-#define CORE_CC_REG(base, field) \
- (base + offsetof(struct chipcregs, field))
-#define CORE_BUS_REG(base, field) \
- (base + offsetof(struct sdpcmd_regs, field))
-#define CORE_SB(base, field) \
- (base + SBCONFIGOFF + offsetof(struct sbconfig, field))
-
/* core registers */
struct sdpcmd_regs {
u32 corecontrol; /* 0x00, rev8 */
/* misc chip info needed by some of the routines */
-struct chip_info {
- u32 chip;
- u32 chiprev;
- u32 cccorebase;
- u32 ccrev;
- u32 cccaps;
- u32 buscorebase; /* 32 bits backplane bus address */
- u32 buscorerev;
- u32 buscoretype;
- u32 ramcorebase;
- u32 armcorebase;
- u32 pmurev;
- u32 ramsize;
-};
-
/* Private data for SDIO bus interaction */
struct brcmf_bus {
struct brcmf_pub *drvr;
uint txminmax;
struct sk_buff *glomd; /* Packet containing glomming descriptor */
- struct sk_buff *glom; /* Packet chain for glommed superframe */
+ struct sk_buff_head glom; /* Packet list for glommed superframe */
uint glomerr; /* Glom packet read errors */
u8 *rxbuf; /* Buffer for receiving control packets */
u32 fw_ptr;
};
-struct sbconfig {
- u32 PAD[2];
- u32 sbipsflag; /* initiator port ocp slave flag */
- u32 PAD[3];
- u32 sbtpsflag; /* target port ocp slave flag */
- u32 PAD[11];
- u32 sbtmerrloga; /* (sonics >= 2.3) */
- u32 PAD;
- u32 sbtmerrlog; /* (sonics >= 2.3) */
- u32 PAD[3];
- u32 sbadmatch3; /* address match3 */
- u32 PAD;
- u32 sbadmatch2; /* address match2 */
- u32 PAD;
- u32 sbadmatch1; /* address match1 */
- u32 PAD[7];
- u32 sbimstate; /* initiator agent state */
- u32 sbintvec; /* interrupt mask */
- u32 sbtmstatelow; /* target state */
- u32 sbtmstatehigh; /* target state */
- u32 sbbwa0; /* bandwidth allocation table0 */
- u32 PAD;
- u32 sbimconfiglow; /* initiator configuration */
- u32 sbimconfighigh; /* initiator configuration */
- u32 sbadmatch0; /* address match0 */
- u32 PAD;
- u32 sbtmconfiglow; /* target configuration */
- u32 sbtmconfighigh; /* target configuration */
- u32 sbbconfig; /* broadcast configuration */
- u32 PAD;
- u32 sbbstate; /* broadcast state */
- u32 PAD[3];
- u32 sbactcnfg; /* activate configuration */
- u32 PAD[3];
- u32 sbflagst; /* current sbflags */
- u32 PAD[3];
- u32 sbidlow; /* identification */
- u32 sbidhigh; /* identification */
-};
-
/* clkstate */
#define CLK_NONE 0
#define CLK_SDONLY 1
clkreq =
bus->alp_only ? SBSDIO_ALP_AVAIL_REQ : SBSDIO_HT_AVAIL_REQ;
- if ((bus->ci->chip == BCM4329_CHIP_ID)
- && (bus->ci->chiprev == 0))
- clkreq |= SBSDIO_FORCE_ALP;
-
brcmf_sdcard_cfg_write(bus->sdiodev, SDIO_FUNC_1,
SBSDIO_FUNC1_CHIPCLKCSR, clkreq, &err);
if (err) {
SBSDIO_FORCE_HW_CLKREQ_OFF, NULL);
/* Isolate the bus */
- if (bus->ci->chip != BCM4329_CHIP_ID) {
- brcmf_sdcard_cfg_write(bus->sdiodev, SDIO_FUNC_1,
- SBSDIO_DEVICE_CTL,
- SBSDIO_DEVCTL_PADS_ISO, NULL);
- }
+ brcmf_sdcard_cfg_write(bus->sdiodev, SDIO_FUNC_1,
+ SBSDIO_DEVICE_CTL,
+ SBSDIO_DEVCTL_PADS_ISO, NULL);
/* Change state */
bus->sleeping = true;
bus->drvr->busstate = BRCMF_BUS_DOWN;
}
+/* copy a buffer into a pkt buffer chain */
+static uint brcmf_sdbrcm_glom_from_buf(struct brcmf_bus *bus, uint len)
+{
+ uint n, ret = 0;
+ struct sk_buff *p;
+ u8 *buf;
+
+ buf = bus->dataptr;
+
+ /* copy the data */
+ skb_queue_walk(&bus->glom, p) {
+ n = min_t(uint, p->len, len);
+ memcpy(p->data, buf, n);
+ buf += n;
+ len -= n;
+ ret += n;
+ if (!len)
+ break;
+ }
+
+ return ret;
+}
+
static u8 brcmf_sdbrcm_rxglom(struct brcmf_bus *bus, u8 rxseq)
{
u16 dlen, totlen;
/* If packets, issue read(s) and send up packet chain */
/* Return sequence numbers consumed? */
- brcmf_dbg(TRACE, "start: glomd %p glom %p\n", bus->glomd, bus->glom);
+ brcmf_dbg(TRACE, "start: glomd %p glom %p\n",
+ bus->glomd, skb_peek(&bus->glom));
/* If there's a descriptor, generate the packet chain */
if (bus->glomd) {
num, sublen);
break;
}
- if (!pfirst) {
- pfirst = plast = pnext;
- } else {
- plast->next = pnext;
- plast = pnext;
- }
+ skb_queue_tail(&bus->glom, pnext);
/* Adhere to start alignment requirements */
pkt_align(pnext, sublen, BRCMF_SDALIGN);
brcmf_dbg(GLOM, "glomdesc mismatch: nextlen %d glomdesc %d rxseq %d\n",
bus->nextlen, totlen, rxseq);
}
- bus->glom = pfirst;
pfirst = pnext = NULL;
} else {
- if (pfirst)
- brcmu_pkt_buf_free_skb(pfirst);
- bus->glom = NULL;
+ if (!skb_queue_empty(&bus->glom))
+ skb_queue_walk_safe(&bus->glom, pfirst, pnext) {
+ skb_unlink(pfirst, &bus->glom);
+ brcmu_pkt_buf_free_skb(pfirst);
+ }
num = 0;
}
/* Ok -- either we just generated a packet chain,
or had one from before */
- if (bus->glom) {
+ if (!skb_queue_empty(&bus->glom)) {
if (BRCMF_GLOM_ON()) {
brcmf_dbg(GLOM, "try superframe read, packet chain:\n");
- for (pnext = bus->glom; pnext; pnext = pnext->next) {
+ skb_queue_walk(&bus->glom, pnext) {
brcmf_dbg(GLOM, " %p: %p len 0x%04x (%d)\n",
pnext, (u8 *) (pnext->data),
pnext->len, pnext->len);
}
}
- pfirst = bus->glom;
+ pfirst = skb_peek(&bus->glom);
dlen = (u16) brcmu_pkttotlen(pfirst);
/* Do an SDIO read for the superframe. Configurable iovar to
SDIO_FUNC_2,
F2SYNC, bus->dataptr, dlen,
NULL);
- sublen = (u16) brcmu_pktfrombuf(pfirst, 0, dlen,
- bus->dataptr);
+ sublen = (u16) brcmf_sdbrcm_glom_from_buf(bus, dlen);
if (sublen != dlen) {
brcmf_dbg(ERROR, "FAILED TO COPY, dlen %d sublen %d\n",
dlen, sublen);
} else {
bus->glomerr = 0;
brcmf_sdbrcm_rxfail(bus, true, false);
- brcmu_pkt_buf_free_skb(bus->glom);
bus->rxglomfail++;
- bus->glom = NULL;
+ skb_queue_walk_safe(&bus->glom, pfirst, pnext) {
+ skb_unlink(pfirst, &bus->glom);
+ brcmu_pkt_buf_free_skb(pfirst);
+ }
}
return 0;
}
} else {
bus->glomerr = 0;
brcmf_sdbrcm_rxfail(bus, true, false);
- brcmu_pkt_buf_free_skb(bus->glom);
bus->rxglomfail++;
- bus->glom = NULL;
+ skb_queue_walk_safe(&bus->glom, pfirst, pnext) {
+ skb_unlink(pfirst, &bus->glom);
+ brcmu_pkt_buf_free_skb(pfirst);
+ }
}
bus->nextlen = 0;
return 0;
/* Basic SD framing looks ok - process each packet (header) */
save_pfirst = pfirst;
- bus->glom = NULL;
plast = NULL;
for (num = 0; pfirst; rxseq++, pfirst = pnext) {
rxseq++, rxleft--) {
/* Handle glomming separately */
- if (bus->glom || bus->glomd) {
+ if (bus->glomd || !skb_queue_empty(&bus->glom)) {
u8 cnt;
brcmf_dbg(GLOM, "calling rxglom: glomd %p, glom %p\n",
- bus->glomd, bus->glom);
+ bus->glomd, skb_peek(&bus->glom));
cnt = brcmf_sdbrcm_rxglom(bus, rxseq);
brcmf_dbg(GLOM, "rxglom returned %d\n", cnt);
rxseq += cnt - 1;
return bcmerror;
}
-static void
-brcmf_sdbrcm_chip_disablecore(struct brcmf_sdio_dev *sdiodev, u32 corebase)
-{
- u32 regdata;
-
- regdata = brcmf_sdcard_reg_read(sdiodev,
- CORE_SB(corebase, sbtmstatelow), 4);
- if (regdata & SBTML_RESET)
- return;
-
- regdata = brcmf_sdcard_reg_read(sdiodev,
- CORE_SB(corebase, sbtmstatelow), 4);
- if ((regdata & (SICF_CLOCK_EN << SBTML_SICF_SHIFT)) != 0) {
- /*
- * set target reject and spin until busy is clear
- * (preserve core-specific bits)
- */
- regdata = brcmf_sdcard_reg_read(sdiodev,
- CORE_SB(corebase, sbtmstatelow), 4);
- brcmf_sdcard_reg_write(sdiodev, CORE_SB(corebase, sbtmstatelow),
- 4, regdata | SBTML_REJ);
-
- regdata = brcmf_sdcard_reg_read(sdiodev,
- CORE_SB(corebase, sbtmstatelow), 4);
- udelay(1);
- SPINWAIT((brcmf_sdcard_reg_read(sdiodev,
- CORE_SB(corebase, sbtmstatehigh), 4) &
- SBTMH_BUSY), 100000);
-
- regdata = brcmf_sdcard_reg_read(sdiodev,
- CORE_SB(corebase, sbtmstatehigh), 4);
- if (regdata & SBTMH_BUSY)
- brcmf_dbg(ERROR, "ARM core still busy\n");
-
- regdata = brcmf_sdcard_reg_read(sdiodev,
- CORE_SB(corebase, sbidlow), 4);
- if (regdata & SBIDL_INIT) {
- regdata = brcmf_sdcard_reg_read(sdiodev,
- CORE_SB(corebase, sbimstate), 4) |
- SBIM_RJ;
- brcmf_sdcard_reg_write(sdiodev,
- CORE_SB(corebase, sbimstate), 4,
- regdata);
- regdata = brcmf_sdcard_reg_read(sdiodev,
- CORE_SB(corebase, sbimstate), 4);
- udelay(1);
- SPINWAIT((brcmf_sdcard_reg_read(sdiodev,
- CORE_SB(corebase, sbimstate), 4) &
- SBIM_BY), 100000);
- }
-
- /* set reset and reject while enabling the clocks */
- brcmf_sdcard_reg_write(sdiodev,
- CORE_SB(corebase, sbtmstatelow), 4,
- (((SICF_FGC | SICF_CLOCK_EN) << SBTML_SICF_SHIFT) |
- SBTML_REJ | SBTML_RESET));
- regdata = brcmf_sdcard_reg_read(sdiodev,
- CORE_SB(corebase, sbtmstatelow), 4);
- udelay(10);
-
- /* clear the initiator reject bit */
- regdata = brcmf_sdcard_reg_read(sdiodev,
- CORE_SB(corebase, sbidlow), 4);
- if (regdata & SBIDL_INIT) {
- regdata = brcmf_sdcard_reg_read(sdiodev,
- CORE_SB(corebase, sbimstate), 4) &
- ~SBIM_RJ;
- brcmf_sdcard_reg_write(sdiodev,
- CORE_SB(corebase, sbimstate), 4,
- regdata);
- }
- }
-
- /* leave reset and reject asserted */
- brcmf_sdcard_reg_write(sdiodev, CORE_SB(corebase, sbtmstatelow), 4,
- (SBTML_REJ | SBTML_RESET));
- udelay(1);
-}
-
static void
brcmf_sdbrcm_chip_resetcore(struct brcmf_sdio_dev *sdiodev, u32 corebase)
{
* Must do the disable sequence first to work for
* arbitrary current core state.
*/
- brcmf_sdbrcm_chip_disablecore(sdiodev, corebase);
+ brcmf_sdio_chip_coredisable(sdiodev, corebase);
/*
* Now do the initialization sequence.
if (enter) {
bus->alp_only = true;
- brcmf_sdbrcm_chip_disablecore(bus->sdiodev,
+ brcmf_sdio_chip_coredisable(bus->sdiodev,
bus->ci->armcorebase);
brcmf_sdbrcm_chip_resetcore(bus->sdiodev, bus->ci->ramcorebase);
u8 saveclk;
uint retries;
int err;
+ struct sk_buff *cur;
+ struct sk_buff *next;
brcmf_dbg(TRACE, "Enter\n");
/* Clear any held glomming stuff */
if (bus->glomd)
brcmu_pkt_buf_free_skb(bus->glomd);
-
- if (bus->glom)
- brcmu_pkt_buf_free_skb(bus->glom);
-
- bus->glom = bus->glomd = NULL;
+ if (!skb_queue_empty(&bus->glom))
+ skb_queue_walk_safe(&bus->glom, cur, next) {
+ skb_unlink(cur, &bus->glom);
+ brcmu_pkt_buf_free_skb(cur);
+ }
/* Clear rx control and wake any waiters */
bus->rxlen = 0;
#define SDIOD_DRVSTR_KEY(chip, pmu) (((chip) << 16) | (pmu))
+static char *brcmf_chipname(uint chipid, char *buf, uint len)
+{
+ const char *fmt;
+
+ fmt = ((chipid > 0xa000) || (chipid < 0x4000)) ? "%d" : "%x";
+ snprintf(buf, len, fmt, chipid);
+ return buf;
+}
+
static void brcmf_sdbrcm_sdiod_drive_strength_init(struct brcmf_bus *bus,
u32 drivestrength) {
struct sdiod_drive_str *str_tab = NULL;
break;
default:
brcmf_dbg(ERROR, "No SDIO Drive strength init done for chip %s rev %d pmurev %d\n",
- brcmu_chipname(bus->ci->chip, chn, 8),
+ brcmf_chipname(bus->ci->chip, chn, 8),
bus->ci->chiprev, bus->ci->pmurev);
break;
}
}
}
-static int
-brcmf_sdbrcm_chip_recognition(struct brcmf_sdio_dev *sdiodev,
- struct chip_info *ci, u32 regs)
-{
- u32 regdata;
-
- /*
- * Get CC core rev
- * Chipid is assume to be at offset 0 from regs arg
- * For different chiptypes or old sdio hosts w/o chipcommon,
- * other ways of recognition should be added here.
- */
- ci->cccorebase = regs;
- regdata = brcmf_sdcard_reg_read(sdiodev,
- CORE_CC_REG(ci->cccorebase, chipid), 4);
- ci->chip = regdata & CID_ID_MASK;
- ci->chiprev = (regdata & CID_REV_MASK) >> CID_REV_SHIFT;
-
- brcmf_dbg(INFO, "chipid=0x%x chiprev=%d\n", ci->chip, ci->chiprev);
-
- /* Address of cores for new chips should be added here */
- switch (ci->chip) {
- case BCM4329_CHIP_ID:
- ci->buscorebase = BCM4329_CORE_BUS_BASE;
- ci->ramcorebase = BCM4329_CORE_SOCRAM_BASE;
- ci->armcorebase = BCM4329_CORE_ARM_BASE;
- ci->ramsize = BCM4329_RAMSIZE;
- break;
- default:
- brcmf_dbg(ERROR, "chipid 0x%x is not supported\n", ci->chip);
- return -ENODEV;
- }
-
- regdata = brcmf_sdcard_reg_read(sdiodev,
- CORE_SB(ci->cccorebase, sbidhigh), 4);
- ci->ccrev = SBCOREREV(regdata);
-
- regdata = brcmf_sdcard_reg_read(sdiodev,
- CORE_CC_REG(ci->cccorebase, pmucapabilities), 4);
- ci->pmurev = regdata & PCAP_REV_MASK;
-
- regdata = brcmf_sdcard_reg_read(sdiodev,
- CORE_SB(ci->buscorebase, sbidhigh), 4);
- ci->buscorerev = SBCOREREV(regdata);
- ci->buscoretype = (regdata & SBIDH_CC_MASK) >> SBIDH_CC_SHIFT;
-
- brcmf_dbg(INFO, "ccrev=%d, pmurev=%d, buscore rev/type=%d/0x%x\n",
- ci->ccrev, ci->pmurev, ci->buscorerev, ci->buscoretype);
-
- /* get chipcommon capabilites */
- ci->cccaps = brcmf_sdcard_reg_read(sdiodev,
- CORE_CC_REG(ci->cccorebase, capabilities), 4);
-
- return 0;
-}
-
-static int
-brcmf_sdbrcm_chip_attach(struct brcmf_bus *bus, u32 regs)
-{
- struct chip_info *ci;
- int err;
- u8 clkval, clkset;
-
- brcmf_dbg(TRACE, "Enter\n");
-
- /* alloc chip_info_t */
- ci = kzalloc(sizeof(struct chip_info), GFP_ATOMIC);
- if (NULL == ci)
- return -ENOMEM;
-
- /* bus/core/clk setup for register access */
- /* Try forcing SDIO core to do ALPAvail request only */
- clkset = SBSDIO_FORCE_HW_CLKREQ_OFF | SBSDIO_ALP_AVAIL_REQ;
- brcmf_sdcard_cfg_write(bus->sdiodev, SDIO_FUNC_1,
- SBSDIO_FUNC1_CHIPCLKCSR, clkset, &err);
- if (err) {
- brcmf_dbg(ERROR, "error writing for HT off\n");
- goto fail;
- }
-
- /* If register supported, wait for ALPAvail and then force ALP */
- /* This may take up to 15 milliseconds */
- clkval = brcmf_sdcard_cfg_read(bus->sdiodev, SDIO_FUNC_1,
- SBSDIO_FUNC1_CHIPCLKCSR, NULL);
- if ((clkval & ~SBSDIO_AVBITS) == clkset) {
- SPINWAIT(((clkval =
- brcmf_sdcard_cfg_read(bus->sdiodev, SDIO_FUNC_1,
- SBSDIO_FUNC1_CHIPCLKCSR,
- NULL)),
- !SBSDIO_ALPAV(clkval)),
- PMU_MAX_TRANSITION_DLY);
- if (!SBSDIO_ALPAV(clkval)) {
- brcmf_dbg(ERROR, "timeout on ALPAV wait, clkval 0x%02x\n",
- clkval);
- err = -EBUSY;
- goto fail;
- }
- clkset = SBSDIO_FORCE_HW_CLKREQ_OFF |
- SBSDIO_FORCE_ALP;
- brcmf_sdcard_cfg_write(bus->sdiodev, SDIO_FUNC_1,
- SBSDIO_FUNC1_CHIPCLKCSR,
- clkset, &err);
- udelay(65);
- } else {
- brcmf_dbg(ERROR, "ChipClkCSR access: wrote 0x%02x read 0x%02x\n",
- clkset, clkval);
- err = -EACCES;
- goto fail;
- }
-
- /* Also, disable the extra SDIO pull-ups */
- brcmf_sdcard_cfg_write(bus->sdiodev, SDIO_FUNC_1,
- SBSDIO_FUNC1_SDIOPULLUP, 0, NULL);
-
- err = brcmf_sdbrcm_chip_recognition(bus->sdiodev, ci, regs);
- if (err)
- goto fail;
-
- /*
- * Make sure any on-chip ARM is off (in case strapping is wrong),
- * or downloaded code was already running.
- */
- brcmf_sdbrcm_chip_disablecore(bus->sdiodev, ci->armcorebase);
-
- brcmf_sdcard_reg_write(bus->sdiodev,
- CORE_CC_REG(ci->cccorebase, gpiopullup), 4, 0);
- brcmf_sdcard_reg_write(bus->sdiodev,
- CORE_CC_REG(ci->cccorebase, gpiopulldown), 4, 0);
-
- /* Disable F2 to clear any intermediate frame state on the dongle */
- brcmf_sdcard_cfg_write(bus->sdiodev, SDIO_FUNC_0, SDIO_CCCR_IOEx,
- SDIO_FUNC_ENABLE_1, NULL);
-
- /* WAR: cmd52 backplane read so core HW will drop ALPReq */
- clkval = brcmf_sdcard_cfg_read(bus->sdiodev, SDIO_FUNC_1,
- 0, NULL);
-
- /* Done with backplane-dependent accesses, can drop clock... */
- brcmf_sdcard_cfg_write(bus->sdiodev, SDIO_FUNC_1,
- SBSDIO_FUNC1_CHIPCLKCSR, 0, NULL);
-
- bus->ci = ci;
- return 0;
-fail:
- bus->ci = NULL;
- kfree(ci);
- return err;
-}
-
static bool
brcmf_sdbrcm_probe_attach(struct brcmf_bus *bus, u32 regsva)
{
#endif /* BCMDBG */
/*
- * Force PLL off until brcmf_sdbrcm_chip_attach()
+ * Force PLL off until brcmf_sdio_chip_attach()
* programs PLL control regs
*/
goto fail;
}
- if (brcmf_sdbrcm_chip_attach(bus, regsva)) {
- brcmf_dbg(ERROR, "brcmf_sdbrcm_chip_attach failed!\n");
+ if (brcmf_sdio_chip_attach(bus->sdiodev, &bus->ci, regsva)) {
+ brcmf_dbg(ERROR, "brcmf_sdio_chip_attach failed!\n");
goto fail;
}
bus->sdiodev = sdiodev;
sdiodev->bus = bus;
+ skb_queue_head_init(&bus->glom);
bus->txbound = BRCMF_TXBOUND;
bus->rxbound = BRCMF_RXBOUND;
bus->txminmax = BRCMF_TXMINMAX;
goto fail;
}
}
- /* Ok, have the per-port tell the stack we're open for business */
- if (brcmf_net_attach(bus->drvr, 0) != 0) {
- brcmf_dbg(ERROR, "Net attach failed!!\n");
+
+ /* add interface and open for business */
+ if (brcmf_add_if((struct brcmf_info *)bus->drvr, 0, "wlan%d", NULL)) {
+ brcmf_dbg(ERROR, "Add primary net device interface failed!!\n");
goto fail;
}
void
brcmf_sdbrcm_wd_timer(struct brcmf_bus *bus, uint wdtick)
{
- /* don't start the wd until fw is loaded */
- if (bus->drvr->busstate == BRCMF_BUS_DOWN)
- return;
-
/* Totally stop the timer */
if (!wdtick && bus->wd_timer_valid == true) {
del_timer_sync(&bus->timer);
return;
}
+ /* don't start the wd until fw is loaded */
+ if (bus->drvr->busstate == BRCMF_BUS_DOWN)
+ return;
+
if (wdtick) {
if (bus->save_ms != BRCMF_WD_POLL_MS) {
if (bus->wd_timer_valid == true)
projects / deliverable / linux.git / blobdiff