#include "iwl-io.h"
#include "iwl-power.h"
#include "iwl-sta.h"
+#include "iwl-agn.h"
#include "iwl-helpers.h"
+#include "iwl-shared.h"
#include "iwl-agn.h"
-
-
-/*
- * set bt_coex_active to true, uCode will do kill/defer
- * every time the priority line is asserted (BT is sending signals on the
- * priority line in the PCIx).
- * set bt_coex_active to false, uCode will ignore the BT activity and
- * perform the normal operation
- *
- * User might experience transmit issue on some platform due to WiFi/BT
- * co-exist problem. The possible behaviors are:
- * Able to scan and finding all the available AP
- * Not able to associate with any AP
- * On those platforms, WiFi communication can be restored by set
- * "bt_coex_active" module parameter to "false"
- *
- * default: bt_coex_active = true (BT_COEX_ENABLE)
- */
-bool bt_coex_active = true;
-module_param(bt_coex_active, bool, S_IRUGO);
-MODULE_PARM_DESC(bt_coex_active, "enable wifi/bluetooth co-exist");
-
-u32 iwl_debug_level;
+#include "iwl-trans.h"
const u8 iwl_bcast_addr[ETH_ALEN] = { 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF };
#define MAX_BIT_RATE_40_MHZ 150 /* Mbps */
#define MAX_BIT_RATE_20_MHZ 72 /* Mbps */
-static void iwlcore_init_ht_hw_capab(const struct iwl_priv *priv,
+static void iwl_init_ht_hw_capab(const struct iwl_priv *priv,
struct ieee80211_sta_ht_cap *ht_info,
enum ieee80211_band band)
{
u16 max_bit_rate = 0;
- u8 rx_chains_num = priv->hw_params.rx_chains_num;
- u8 tx_chains_num = priv->hw_params.tx_chains_num;
+ u8 rx_chains_num = hw_params(priv).rx_chains_num;
+ u8 tx_chains_num = hw_params(priv).tx_chains_num;
ht_info->cap = 0;
memset(&ht_info->mcs, 0, sizeof(ht_info->mcs));
ht_info->cap |= IEEE80211_HT_CAP_GRN_FLD;
ht_info->cap |= IEEE80211_HT_CAP_SGI_20;
max_bit_rate = MAX_BIT_RATE_20_MHZ;
- if (priv->hw_params.ht40_channel & BIT(band)) {
+ if (hw_params(priv).ht40_channel & BIT(band)) {
ht_info->cap |= IEEE80211_HT_CAP_SUP_WIDTH_20_40;
ht_info->cap |= IEEE80211_HT_CAP_SGI_40;
ht_info->mcs.rx_mask[4] = 0x01;
}
/**
- * iwlcore_init_geos - Initialize mac80211's geo/channel info based from eeprom
+ * iwl_init_geos - Initialize mac80211's geo/channel info based from eeprom
*/
-int iwlcore_init_geos(struct iwl_priv *priv)
+int iwl_init_geos(struct iwl_priv *priv)
{
struct iwl_channel_info *ch;
struct ieee80211_supported_band *sband;
if (priv->bands[IEEE80211_BAND_2GHZ].n_bitrates ||
priv->bands[IEEE80211_BAND_5GHZ].n_bitrates) {
IWL_DEBUG_INFO(priv, "Geography modes already initialized.\n");
- set_bit(STATUS_GEO_CONFIGURED, &priv->status);
+ set_bit(STATUS_GEO_CONFIGURED, &priv->shrd->status);
return 0;
}
sband->bitrates = &rates[IWL_FIRST_OFDM_RATE];
sband->n_bitrates = IWL_RATE_COUNT_LEGACY - IWL_FIRST_OFDM_RATE;
- if (priv->cfg->sku & IWL_SKU_N)
- iwlcore_init_ht_hw_capab(priv, &sband->ht_cap,
+ if (priv->cfg->sku & EEPROM_SKU_CAP_11N_ENABLE)
+ iwl_init_ht_hw_capab(priv, &sband->ht_cap,
IEEE80211_BAND_5GHZ);
sband = &priv->bands[IEEE80211_BAND_2GHZ];
sband->bitrates = rates;
sband->n_bitrates = IWL_RATE_COUNT_LEGACY;
- if (priv->cfg->sku & IWL_SKU_N)
- iwlcore_init_ht_hw_capab(priv, &sband->ht_cap,
+ if (priv->cfg->sku & EEPROM_SKU_CAP_11N_ENABLE)
+ iwl_init_ht_hw_capab(priv, &sband->ht_cap,
IEEE80211_BAND_2GHZ);
priv->ieee_channels = channels;
priv->tx_power_next = max_tx_power;
if ((priv->bands[IEEE80211_BAND_5GHZ].n_channels == 0) &&
- priv->cfg->sku & IWL_SKU_A) {
+ priv->cfg->sku & EEPROM_SKU_CAP_BAND_52GHZ) {
+ char buf[32];
+ bus_get_hw_id(priv->bus, buf, sizeof(buf));
IWL_INFO(priv, "Incorrectly detected BG card as ABG. "
- "Please send your PCI ID 0x%04X:0x%04X to maintainer.\n",
- priv->pci_dev->device,
- priv->pci_dev->subsystem_device);
- priv->cfg->sku &= ~IWL_SKU_A;
+ "Please send your %s to maintainer.\n", buf);
+ priv->cfg->sku &= ~EEPROM_SKU_CAP_BAND_52GHZ;
}
IWL_INFO(priv, "Tunable channels: %d 802.11bg, %d 802.11a channels\n",
priv->bands[IEEE80211_BAND_2GHZ].n_channels,
priv->bands[IEEE80211_BAND_5GHZ].n_channels);
- set_bit(STATUS_GEO_CONFIGURED, &priv->status);
+ set_bit(STATUS_GEO_CONFIGURED, &priv->shrd->status);
return 0;
}
/*
- * iwlcore_free_geos - undo allocations in iwlcore_init_geos
+ * iwl_free_geos - undo allocations in iwl_init_geos
*/
-void iwlcore_free_geos(struct iwl_priv *priv)
+void iwl_free_geos(struct iwl_priv *priv)
{
kfree(priv->ieee_channels);
kfree(priv->ieee_rates);
- clear_bit(STATUS_GEO_CONFIGURED, &priv->status);
+ clear_bit(STATUS_GEO_CONFIGURED, &priv->shrd->status);
}
static bool iwl_is_channel_extension(struct iwl_priv *priv,
conf = ieee80211_get_hw_conf(priv->hw);
- lockdep_assert_held(&priv->mutex);
+ lockdep_assert_held(&priv->shrd->mutex);
memset(&ctx->timing, 0, sizeof(struct iwl_rxon_time_cmd));
beacon_int = le16_to_cpu(ctx->timing.beacon_interval);
} else {
beacon_int = iwl_adjust_beacon_interval(beacon_int,
- priv->hw_params.max_beacon_itrvl * TIME_UNIT);
+ IWL_MAX_UCODE_BEACON_INTERVAL * TIME_UNIT);
ctx->timing.beacon_interval = cpu_to_le16(beacon_int);
}
+ ctx->beacon_int = beacon_int;
+
tsf = priv->timestamp; /* tsf is modifed by do_div: copy it */
interval_tm = beacon_int * TIME_UNIT;
rem = do_div(tsf, interval_tm);
le32_to_cpu(ctx->timing.beacon_init_val),
le16_to_cpu(ctx->timing.atim_window));
- return iwl_send_cmd_pdu(priv, ctx->rxon_timing_cmd,
- sizeof(ctx->timing), &ctx->timing);
+ return iwl_trans_send_cmd_pdu(trans(priv), ctx->rxon_timing_cmd,
+ CMD_SYNC, sizeof(ctx->timing), &ctx->timing);
}
void iwl_set_rxon_hwcrypto(struct iwl_priv *priv, struct iwl_rxon_context *ctx,
return 0;
}
-u8 iwl_rate_get_lowest_plcp(struct iwl_priv *priv,
- struct iwl_rxon_context *ctx)
-{
- /*
- * Assign the lowest rate -- should really get this from
- * the beacon skb from mac80211.
- */
- if (ctx->staging.flags & RXON_FLG_BAND_24G_MSK)
- return IWL_RATE_1M_PLCP;
- else
- return IWL_RATE_6M_PLCP;
-}
-
static void _iwl_set_rxon_ht(struct iwl_priv *priv,
struct iwl_ht_config *ht_conf,
struct iwl_rxon_context *ctx)
rxon->flags |= RXON_FLG_CHANNEL_MODE_LEGACY;
}
- if (priv->cfg->ops->hcmd->set_rxon_chain)
- priv->cfg->ops->hcmd->set_rxon_chain(priv, ctx);
+ iwlagn_set_rxon_chain(priv, ctx);
IWL_DEBUG_ASSOC(priv, "rxon flags 0x%X operation mode :0x%X "
"extension channel offset 0x%x\n",
*/
struct iwl_rxon_context *ctx = &priv->contexts[IWL_RXON_CTX_BSS];
- if (test_bit(STATUS_EXIT_PENDING, &priv->status))
+ if (test_bit(STATUS_EXIT_PENDING, &priv->shrd->status))
return;
- if (test_and_clear_bit(STATUS_CHANNEL_SWITCH_PENDING, &priv->status))
+ if (test_and_clear_bit(STATUS_CHANNEL_SWITCH_PENDING,
+ &priv->shrd->status))
ieee80211_chswitch_done(ctx->vif, is_success);
}
unsigned long flags;
struct iwl_notification_wait *wait_entry;
- spin_lock_irqsave(&priv->_agn.notif_wait_lock, flags);
- list_for_each_entry(wait_entry, &priv->_agn.notif_waits, list)
+ spin_lock_irqsave(&priv->notif_wait_lock, flags);
+ list_for_each_entry(wait_entry, &priv->notif_waits, list)
wait_entry->aborted = true;
- spin_unlock_irqrestore(&priv->_agn.notif_wait_lock, flags);
+ spin_unlock_irqrestore(&priv->notif_wait_lock, flags);
- wake_up_all(&priv->_agn.notif_waitq);
+ wake_up_all(&priv->notif_waitq);
}
void iwlagn_fw_error(struct iwl_priv *priv, bool ondemand)
unsigned long reload_jiffies;
/* Set the FW error flag -- cleared on iwl_down */
- set_bit(STATUS_FW_ERROR, &priv->status);
+ set_bit(STATUS_FW_ERROR, &priv->shrd->status);
/* Cancel currently queued command. */
- clear_bit(STATUS_HCMD_ACTIVE, &priv->status);
+ clear_bit(STATUS_HCMD_ACTIVE, &priv->shrd->status);
iwlagn_abort_notification_waits(priv);
/* Keep the restart process from trying to send host
* commands by clearing the ready bit */
- clear_bit(STATUS_READY, &priv->status);
+ clear_bit(STATUS_READY, &priv->shrd->status);
- wake_up_interruptible(&priv->wait_command_queue);
+ wake_up_interruptible(&priv->shrd->wait_command_queue);
if (!ondemand) {
/*
priv->reload_count = 0;
}
- if (!test_bit(STATUS_EXIT_PENDING, &priv->status)) {
+ if (!test_bit(STATUS_EXIT_PENDING, &priv->shrd->status)) {
if (iwlagn_mod_params.restart_fw) {
- IWL_DEBUG(priv, IWL_DL_FW_ERRORS,
+ IWL_DEBUG_FW_ERRORS(priv,
"Restarting adapter due to uCode error.\n");
- queue_work(priv->workqueue, &priv->restart);
+ queue_work(priv->shrd->workqueue, &priv->restart);
} else
- IWL_DEBUG(priv, IWL_DL_FW_ERRORS,
+ IWL_DEBUG_FW_ERRORS(priv,
"Detected FW error, but not restarting\n");
}
}
-/**
- * iwl_irq_handle_error - called for HW or SW error interrupt from card
- */
-void iwl_irq_handle_error(struct iwl_priv *priv)
-{
- /* W/A for WiFi/WiMAX coex and WiMAX own the RF */
- if (priv->cfg->internal_wimax_coex &&
- (!(iwl_read_prph(priv, APMG_CLK_CTRL_REG) &
- APMS_CLK_VAL_MRB_FUNC_MODE) ||
- (iwl_read_prph(priv, APMG_PS_CTRL_REG) &
- APMG_PS_CTRL_VAL_RESET_REQ))) {
- /*
- * Keep the restart process from trying to send host
- * commands by clearing the ready bit.
- */
- clear_bit(STATUS_READY, &priv->status);
- clear_bit(STATUS_HCMD_ACTIVE, &priv->status);
- wake_up_interruptible(&priv->wait_command_queue);
- IWL_ERR(priv, "RF is used by WiMAX\n");
- return;
- }
-
- IWL_ERR(priv, "Loaded firmware version: %s\n",
- priv->hw->wiphy->fw_version);
-
- iwl_dump_nic_error_log(priv);
- iwl_dump_csr(priv);
- iwl_dump_fh(priv, NULL, false);
- iwl_dump_nic_event_log(priv, false, NULL, false);
-#ifdef CONFIG_IWLWIFI_DEBUG
- if (iwl_get_debug_level(priv) & IWL_DL_FW_ERRORS)
- iwl_print_rx_config_cmd(priv,
- &priv->contexts[IWL_RXON_CTX_BSS]);
-#endif
-
- iwlagn_fw_error(priv, false);
-}
-
static int iwl_apm_stop_master(struct iwl_priv *priv)
{
int ret = 0;
/* stop device's busmaster DMA activity */
- iwl_set_bit(priv, CSR_RESET, CSR_RESET_REG_FLAG_STOP_MASTER);
+ iwl_set_bit(bus(priv), CSR_RESET, CSR_RESET_REG_FLAG_STOP_MASTER);
- ret = iwl_poll_bit(priv, CSR_RESET, CSR_RESET_REG_FLAG_MASTER_DISABLED,
+ ret = iwl_poll_bit(bus(priv), CSR_RESET,
+ CSR_RESET_REG_FLAG_MASTER_DISABLED,
CSR_RESET_REG_FLAG_MASTER_DISABLED, 100);
if (ret)
IWL_WARN(priv, "Master Disable Timed Out, 100 usec\n");
{
IWL_DEBUG_INFO(priv, "Stop card, put in low power state\n");
- clear_bit(STATUS_DEVICE_ENABLED, &priv->status);
+ clear_bit(STATUS_DEVICE_ENABLED, &priv->shrd->status);
/* Stop device's DMA activity */
iwl_apm_stop_master(priv);
/* Reset the entire device */
- iwl_set_bit(priv, CSR_RESET, CSR_RESET_REG_FLAG_SW_RESET);
+ iwl_set_bit(bus(priv), CSR_RESET, CSR_RESET_REG_FLAG_SW_RESET);
udelay(10);
* Clear "initialization complete" bit to move adapter from
* D0A* (powered-up Active) --> D0U* (Uninitialized) state.
*/
- iwl_clear_bit(priv, CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_INIT_DONE);
+ iwl_clear_bit(bus(priv), CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_INIT_DONE);
}
int iwl_apm_init(struct iwl_priv *priv)
{
int ret = 0;
- u16 lctl;
-
IWL_DEBUG_INFO(priv, "Init card's basic functions\n");
/*
*/
/* Disable L0S exit timer (platform NMI Work/Around) */
- iwl_set_bit(priv, CSR_GIO_CHICKEN_BITS,
+ iwl_set_bit(bus(priv), CSR_GIO_CHICKEN_BITS,
CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER);
/*
* Disable L0s without affecting L1;
* don't wait for ICH L0s (ICH bug W/A)
*/
- iwl_set_bit(priv, CSR_GIO_CHICKEN_BITS,
+ iwl_set_bit(bus(priv), CSR_GIO_CHICKEN_BITS,
CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX);
/* Set FH wait threshold to maximum (HW error during stress W/A) */
- iwl_set_bit(priv, CSR_DBG_HPET_MEM_REG, CSR_DBG_HPET_MEM_REG_VAL);
+ iwl_set_bit(bus(priv), CSR_DBG_HPET_MEM_REG, CSR_DBG_HPET_MEM_REG_VAL);
/*
* Enable HAP INTA (interrupt from management bus) to
* wake device's PCI Express link L1a -> L0s
*/
- iwl_set_bit(priv, CSR_HW_IF_CONFIG_REG,
+ iwl_set_bit(bus(priv), CSR_HW_IF_CONFIG_REG,
CSR_HW_IF_CONFIG_REG_BIT_HAP_WAKE_L1A);
- /*
- * HW bug W/A for instability in PCIe bus L0->L0S->L1 transition.
- * Check if BIOS (or OS) enabled L1-ASPM on this device.
- * If so (likely), disable L0S, so device moves directly L0->L1;
- * costs negligible amount of power savings.
- * If not (unlikely), enable L0S, so there is at least some
- * power savings, even without L1.
- */
- lctl = iwl_pcie_link_ctl(priv);
- if ((lctl & PCI_CFG_LINK_CTRL_VAL_L1_EN) ==
- PCI_CFG_LINK_CTRL_VAL_L1_EN) {
- /* L1-ASPM enabled; disable(!) L0S */
- iwl_set_bit(priv, CSR_GIO_REG,
- CSR_GIO_REG_VAL_L0S_ENABLED);
- IWL_DEBUG_POWER(priv, "L1 Enabled; Disabling L0S\n");
- } else {
- /* L1-ASPM disabled; enable(!) L0S */
- iwl_clear_bit(priv, CSR_GIO_REG,
- CSR_GIO_REG_VAL_L0S_ENABLED);
- IWL_DEBUG_POWER(priv, "L1 Disabled; Enabling L0S\n");
- }
+ bus_apm_config(priv->bus);
/* Configure analog phase-lock-loop before activating to D0A */
if (priv->cfg->base_params->pll_cfg_val)
- iwl_set_bit(priv, CSR_ANA_PLL_CFG,
+ iwl_set_bit(bus(priv), CSR_ANA_PLL_CFG,
priv->cfg->base_params->pll_cfg_val);
/*
* Set "initialization complete" bit to move adapter from
* D0U* --> D0A* (powered-up active) state.
*/
- iwl_set_bit(priv, CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_INIT_DONE);
+ iwl_set_bit(bus(priv), CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_INIT_DONE);
/*
* Wait for clock stabilization; once stabilized, access to
* device-internal resources is supported, e.g. iwl_write_prph()
* and accesses to uCode SRAM.
*/
- ret = iwl_poll_bit(priv, CSR_GP_CNTRL,
+ ret = iwl_poll_bit(bus(priv), CSR_GP_CNTRL,
CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY,
CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY, 25000);
if (ret < 0) {
* do not disable clocks. This preserves any hardware bits already
* set by default in "CLK_CTRL_REG" after reset.
*/
- iwl_write_prph(priv, APMG_CLK_EN_REG, APMG_CLK_VAL_DMA_CLK_RQT);
+ iwl_write_prph(bus(priv), APMG_CLK_EN_REG, APMG_CLK_VAL_DMA_CLK_RQT);
udelay(20);
/* Disable L1-Active */
- iwl_set_bits_prph(priv, APMG_PCIDEV_STT_REG,
+ iwl_set_bits_prph(bus(priv), APMG_PCIDEV_STT_REG,
APMG_PCIDEV_STT_VAL_L1_ACT_DIS);
- set_bit(STATUS_DEVICE_ENABLED, &priv->status);
+ set_bit(STATUS_DEVICE_ENABLED, &priv->shrd->status);
out:
return ret;
bool defer;
struct iwl_rxon_context *ctx = &priv->contexts[IWL_RXON_CTX_BSS];
- lockdep_assert_held(&priv->mutex);
+ lockdep_assert_held(&priv->shrd->mutex);
if (priv->tx_power_user_lmt == tx_power && !force)
return 0;
- if (!priv->cfg->ops->lib->send_tx_power)
- return -EOPNOTSUPP;
-
if (tx_power < IWLAGN_TX_POWER_TARGET_POWER_MIN) {
IWL_WARN(priv,
"Requested user TXPOWER %d below lower limit %d.\n",
return -EINVAL;
}
- if (!iwl_is_ready_rf(priv))
+ if (!iwl_is_ready_rf(priv->shrd))
return -EIO;
/* scan complete and commit_rxon use tx_power_next value,
priv->tx_power_next = tx_power;
/* do not set tx power when scanning or channel changing */
- defer = test_bit(STATUS_SCANNING, &priv->status) ||
+ defer = test_bit(STATUS_SCANNING, &priv->shrd->status) ||
memcmp(&ctx->active, &ctx->staging, sizeof(ctx->staging));
if (defer && !force) {
IWL_DEBUG_INFO(priv, "Deferring tx power set\n");
prev_tx_power = priv->tx_power_user_lmt;
priv->tx_power_user_lmt = tx_power;
- ret = priv->cfg->ops->lib->send_tx_power(priv);
+ ret = iwlagn_send_tx_power(priv);
/* if fail to set tx_power, restore the orig. tx power */
if (ret) {
.kill_cts_mask = 0,
};
- if (!bt_coex_active)
+ if (!iwlagn_mod_params.bt_coex_active)
bt_cmd.flags = BT_COEX_DISABLE;
else
bt_cmd.flags = BT_COEX_ENABLE;
IWL_DEBUG_INFO(priv, "BT coex %s\n",
(bt_cmd.flags == BT_COEX_DISABLE) ? "disable" : "active");
- if (iwl_send_cmd_pdu(priv, REPLY_BT_CONFIG,
- sizeof(struct iwl_bt_cmd), &bt_cmd))
+ if (iwl_trans_send_cmd_pdu(trans(priv), REPLY_BT_CONFIG,
+ CMD_SYNC, sizeof(struct iwl_bt_cmd), &bt_cmd))
IWL_ERR(priv, "failed to send BT Coex Config\n");
}
};
if (flags & CMD_ASYNC)
- return iwl_send_cmd_pdu_async(priv, REPLY_STATISTICS_CMD,
+ return iwl_trans_send_cmd_pdu(trans(priv), REPLY_STATISTICS_CMD,
+ CMD_ASYNC,
sizeof(struct iwl_statistics_cmd),
- &statistics_cmd, NULL);
+ &statistics_cmd);
else
- return iwl_send_cmd_pdu(priv, REPLY_STATISTICS_CMD,
+ return iwl_trans_send_cmd_pdu(trans(priv), REPLY_STATISTICS_CMD,
+ CMD_SYNC,
sizeof(struct iwl_statistics_cmd),
&statistics_cmd);
}
-void iwl_clear_isr_stats(struct iwl_priv *priv)
-{
- memset(&priv->isr_stats, 0, sizeof(priv->isr_stats));
-}
-
int iwl_mac_conf_tx(struct ieee80211_hw *hw, u16 queue,
const struct ieee80211_tx_queue_params *params)
{
IWL_DEBUG_MAC80211(priv, "enter\n");
- if (!iwl_is_ready_rf(priv)) {
+ if (!iwl_is_ready_rf(priv->shrd)) {
IWL_DEBUG_MAC80211(priv, "leave - RF not ready\n");
return -EIO;
}
q = AC_NUM - 1 - queue;
- spin_lock_irqsave(&priv->lock, flags);
+ spin_lock_irqsave(&priv->shrd->lock, flags);
/*
* MULTI-FIXME
ctx->qos_data.def_qos_parm.ac[q].reserved1 = 0;
}
- spin_unlock_irqrestore(&priv->lock, flags);
+ spin_unlock_irqrestore(&priv->shrd->lock, flags);
IWL_DEBUG_MAC80211(priv, "leave\n");
return 0;
{
iwl_connection_init_rx_config(priv, ctx);
- if (priv->cfg->ops->hcmd->set_rxon_chain)
- priv->cfg->ops->hcmd->set_rxon_chain(priv, ctx);
+ iwlagn_set_rxon_chain(priv, ctx);
- return iwlcore_commit_rxon(priv, ctx);
+ return iwlagn_commit_rxon(priv, ctx);
}
static int iwl_setup_interface(struct iwl_priv *priv,
struct ieee80211_vif *vif = ctx->vif;
int err;
- lockdep_assert_held(&priv->mutex);
+ lockdep_assert_held(&priv->shrd->mutex);
/*
* This variable will be correct only when there's just
IWL_DEBUG_MAC80211(priv, "enter: type %d, addr %pM\n",
viftype, vif->addr);
- mutex_lock(&priv->mutex);
+ cancel_delayed_work_sync(&priv->hw_roc_disable_work);
- if (!iwl_is_ready_rf(priv)) {
+ mutex_lock(&priv->shrd->mutex);
+
+ iwlagn_disable_roc(priv);
+
+ if (!iwl_is_ready_rf(priv->shrd)) {
IWL_WARN(priv, "Try to add interface when device not ready\n");
err = -EINVAL;
goto out;
ctx->vif = NULL;
priv->iw_mode = NL80211_IFTYPE_STATION;
out:
- mutex_unlock(&priv->mutex);
+ mutex_unlock(&priv->shrd->mutex);
IWL_DEBUG_MAC80211(priv, "leave\n");
return err;
{
struct iwl_rxon_context *ctx = iwl_rxon_ctx_from_vif(vif);
- lockdep_assert_held(&priv->mutex);
+ lockdep_assert_held(&priv->shrd->mutex);
if (priv->scan_vif == vif) {
iwl_scan_cancel_timeout(priv, 200);
IWL_DEBUG_MAC80211(priv, "enter\n");
- mutex_lock(&priv->mutex);
+ mutex_lock(&priv->shrd->mutex);
WARN_ON(ctx->vif != vif);
ctx->vif = NULL;
iwl_teardown_interface(priv, vif, false);
- mutex_unlock(&priv->mutex);
+ mutex_unlock(&priv->shrd->mutex);
IWL_DEBUG_MAC80211(priv, "leave\n");
}
-int iwl_alloc_txq_mem(struct iwl_priv *priv)
-{
- if (!priv->txq)
- priv->txq = kzalloc(
- sizeof(struct iwl_tx_queue) *
- priv->cfg->base_params->num_of_queues,
- GFP_KERNEL);
- if (!priv->txq) {
- IWL_ERR(priv, "Not enough memory for txq\n");
- return -ENOMEM;
- }
- return 0;
-}
-
-void iwl_free_txq_mem(struct iwl_priv *priv)
-{
- kfree(priv->txq);
- priv->txq = NULL;
-}
-
#ifdef CONFIG_IWLWIFI_DEBUGFS
#define IWL_TRAFFIC_DUMP_SIZE (IWL_TRAFFIC_ENTRY_SIZE * IWL_TRAFFIC_ENTRIES)
{
u32 traffic_size = IWL_TRAFFIC_DUMP_SIZE;
- if (iwl_debug_level & IWL_DL_TX) {
+ if (iwl_get_debug_level(priv->shrd) & IWL_DL_TX) {
if (!priv->tx_traffic) {
priv->tx_traffic =
kzalloc(traffic_size, GFP_KERNEL);
return -ENOMEM;
}
}
- if (iwl_debug_level & IWL_DL_RX) {
+ if (iwl_get_debug_level(priv->shrd) & IWL_DL_RX) {
if (!priv->rx_traffic) {
priv->rx_traffic =
kzalloc(traffic_size, GFP_KERNEL);
__le16 fc;
u16 len;
- if (likely(!(iwl_debug_level & IWL_DL_TX)))
+ if (likely(!(iwl_get_debug_level(priv->shrd) & IWL_DL_TX)))
return;
if (!priv->tx_traffic)
__le16 fc;
u16 len;
- if (likely(!(iwl_debug_level & IWL_DL_RX)))
+ if (likely(!(iwl_get_debug_level(priv->shrd) & IWL_DL_RX)))
return;
if (!priv->rx_traffic)
static void iwl_force_rf_reset(struct iwl_priv *priv)
{
- if (test_bit(STATUS_EXIT_PENDING, &priv->status))
+ if (test_bit(STATUS_EXIT_PENDING, &priv->shrd->status))
return;
if (!iwl_is_any_associated(priv)) {
{
struct iwl_force_reset *force_reset;
- if (test_bit(STATUS_EXIT_PENDING, &priv->status))
+ if (test_bit(STATUS_EXIT_PENDING, &priv->shrd->status))
return -EINVAL;
if (mode >= IWL_MAX_FORCE_RESET) {
newtype = ieee80211_iftype_p2p(newtype, newp2p);
- mutex_lock(&priv->mutex);
+ mutex_lock(&priv->shrd->mutex);
- if (!ctx->vif || !iwl_is_ready_rf(priv)) {
+ if (!ctx->vif || !iwl_is_ready_rf(priv->shrd)) {
/*
* Huh? But wait ... this can maybe happen when
* we're in the middle of a firmware restart!
err = 0;
out:
- mutex_unlock(&priv->mutex);
+ mutex_unlock(&priv->shrd->mutex);
return err;
}
-/*
- * On every watchdog tick we check (latest) time stamp. If it does not
- * change during timeout period and queue is not empty we reset firmware.
- */
-static int iwl_check_stuck_queue(struct iwl_priv *priv, int cnt)
+static inline int iwl_check_stuck_queue(struct iwl_priv *priv, int txq)
{
- struct iwl_tx_queue *txq = &priv->txq[cnt];
- struct iwl_queue *q = &txq->q;
- unsigned long timeout;
- int ret;
-
- if (q->read_ptr == q->write_ptr) {
- txq->time_stamp = jiffies;
- return 0;
- }
-
- timeout = txq->time_stamp +
- msecs_to_jiffies(priv->cfg->base_params->wd_timeout);
-
- if (time_after(jiffies, timeout)) {
- IWL_ERR(priv, "Queue %d stuck for %u ms.\n",
- q->id, priv->cfg->base_params->wd_timeout);
- ret = iwl_force_reset(priv, IWL_FW_RESET, false);
+ if (iwl_trans_check_stuck_queue(trans(priv), txq)) {
+ int ret = iwl_force_reset(priv, IWL_FW_RESET, false);
return (ret == -EAGAIN) ? 0 : 1;
}
-
return 0;
}
int cnt;
unsigned long timeout;
- if (test_bit(STATUS_EXIT_PENDING, &priv->status))
+ if (test_bit(STATUS_EXIT_PENDING, &priv->shrd->status))
return;
timeout = priv->cfg->base_params->wd_timeout;
return;
/* monitor and check for stuck cmd queue */
- if (iwl_check_stuck_queue(priv, priv->cmd_queue))
+ if (iwl_check_stuck_queue(priv, priv->shrd->cmd_queue))
return;
/* monitor and check for other stuck queues */
if (iwl_is_any_associated(priv)) {
- for (cnt = 0; cnt < priv->hw_params.max_txq_num; cnt++) {
+ for (cnt = 0; cnt < hw_params(priv).max_txq_num; cnt++) {
/* skip as we already checked the command queue */
- if (cnt == priv->cmd_queue)
+ if (cnt == priv->shrd->cmd_queue)
continue;
if (iwl_check_stuck_queue(priv, cnt))
return;
{
unsigned int timeout = priv->cfg->base_params->wd_timeout;
- if (timeout)
+ if (timeout && !iwlagn_mod_params.wd_disable)
mod_timer(&priv->watchdog,
jiffies + msecs_to_jiffies(IWL_WD_TICK(timeout)));
else
quot = (usec / interval) &
(iwl_beacon_time_mask_high(priv,
- priv->hw_params.beacon_time_tsf_bits) >>
- priv->hw_params.beacon_time_tsf_bits);
+ hw_params(priv).beacon_time_tsf_bits) >>
+ hw_params(priv).beacon_time_tsf_bits);
rem = (usec % interval) & iwl_beacon_time_mask_low(priv,
- priv->hw_params.beacon_time_tsf_bits);
+ hw_params(priv).beacon_time_tsf_bits);
- return (quot << priv->hw_params.beacon_time_tsf_bits) + rem;
+ return (quot << hw_params(priv).beacon_time_tsf_bits) + rem;
}
/* base is usually what we get from ucode with each received frame,
u32 addon, u32 beacon_interval)
{
u32 base_low = base & iwl_beacon_time_mask_low(priv,
- priv->hw_params.beacon_time_tsf_bits);
+ hw_params(priv).beacon_time_tsf_bits);
u32 addon_low = addon & iwl_beacon_time_mask_low(priv,
- priv->hw_params.beacon_time_tsf_bits);
+ hw_params(priv).beacon_time_tsf_bits);
u32 interval = beacon_interval * TIME_UNIT;
u32 res = (base & iwl_beacon_time_mask_high(priv,
- priv->hw_params.beacon_time_tsf_bits)) +
+ hw_params(priv).beacon_time_tsf_bits)) +
(addon & iwl_beacon_time_mask_high(priv,
- priv->hw_params.beacon_time_tsf_bits));
+ hw_params(priv).beacon_time_tsf_bits));
if (base_low > addon_low)
res += base_low - addon_low;
else if (base_low < addon_low) {
res += interval + base_low - addon_low;
- res += (1 << priv->hw_params.beacon_time_tsf_bits);
+ res += (1 << hw_params(priv).beacon_time_tsf_bits);
} else
- res += (1 << priv->hw_params.beacon_time_tsf_bits);
+ res += (1 << hw_params(priv).beacon_time_tsf_bits);
return cpu_to_le32(res);
}
-#ifdef CONFIG_PM
-
-int iwl_pci_suspend(struct device *device)
+void iwl_start_tx_ba_trans_ready(struct iwl_priv *priv,
+ enum iwl_rxon_context_id ctx,
+ u8 sta_id, u8 tid)
{
- struct pci_dev *pdev = to_pci_dev(device);
- struct iwl_priv *priv = pci_get_drvdata(pdev);
+ struct ieee80211_vif *vif;
+ u8 *addr = priv->stations[sta_id].sta.sta.addr;
- /*
- * This function is called when system goes into suspend state
- * mac80211 will call iwl_mac_stop() from the mac80211 suspend function
- * first but since iwl_mac_stop() has no knowledge of who the caller is,
- * it will not call apm_ops.stop() to stop the DMA operation.
- * Calling apm_ops.stop here to make sure we stop the DMA.
- */
- iwl_apm_stop(priv);
+ if (ctx == NUM_IWL_RXON_CTX)
+ ctx = priv->stations[sta_id].ctxid;
+ vif = priv->contexts[ctx].vif;
- return 0;
+ ieee80211_start_tx_ba_cb_irqsafe(vif, addr, tid);
}
-int iwl_pci_resume(struct device *device)
+void iwl_stop_tx_ba_trans_ready(struct iwl_priv *priv,
+ enum iwl_rxon_context_id ctx,
+ u8 sta_id, u8 tid)
{
- struct pci_dev *pdev = to_pci_dev(device);
- struct iwl_priv *priv = pci_get_drvdata(pdev);
- bool hw_rfkill = false;
-
- /*
- * We disable the RETRY_TIMEOUT register (0x41) to keep
- * PCI Tx retries from interfering with C3 CPU state.
- */
- pci_write_config_byte(pdev, PCI_CFG_RETRY_TIMEOUT, 0x00);
-
- iwl_enable_interrupts(priv);
-
- if (!(iwl_read32(priv, CSR_GP_CNTRL) &
- CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW))
- hw_rfkill = true;
-
- if (hw_rfkill)
- set_bit(STATUS_RF_KILL_HW, &priv->status);
- else
- clear_bit(STATUS_RF_KILL_HW, &priv->status);
+ struct ieee80211_vif *vif;
+ u8 *addr = priv->stations[sta_id].sta.sta.addr;
- wiphy_rfkill_set_hw_state(priv->hw->wiphy, hw_rfkill);
+ if (ctx == NUM_IWL_RXON_CTX)
+ ctx = priv->stations[sta_id].ctxid;
+ vif = priv->contexts[ctx].vif;
- return 0;
+ ieee80211_stop_tx_ba_cb_irqsafe(vif, addr, tid);
}
-const struct dev_pm_ops iwl_pm_ops = {
- .suspend = iwl_pci_suspend,
- .resume = iwl_pci_resume,
- .freeze = iwl_pci_suspend,
- .thaw = iwl_pci_resume,
- .poweroff = iwl_pci_suspend,
- .restore = iwl_pci_resume,
-};
-
-#endif /* CONFIG_PM */
+void iwl_set_hw_rfkill_state(struct iwl_priv *priv, bool state)
+{
+ wiphy_rfkill_set_hw_state(priv->hw->wiphy, state);
+}