enum ieee80211_smps_mode smps_mode;
};
-/**
- * struct iwl_cfg
- * @name: Offical name of the device
- * @fw_name_pre: Firmware filename prefix. The api version and extension
- * (.ucode) will be added to filename before loading from disk. The
- * filename is constructed as fw_name_pre<api>.ucode.
- * @ucode_api_max: Highest version of uCode API supported by driver.
- * @ucode_api_ok: oldest version of the uCode API that is OK to load
- * without a warning, for use in transitions
- * @ucode_api_min: Lowest version of uCode API supported by driver.
- * @valid_tx_ant: valid transmit antenna
- * @valid_rx_ant: valid receive antenna
- * @sku: sku information from EEPROM
- * @eeprom_ver: EEPROM version
- * @eeprom_calib_ver: EEPROM calibration version
- * @lib: pointer to the lib ops
- * @additional_nic_config: additional nic configuration
- * @base_params: pointer to basic parameters
- * @ht_params: point to ht patameters
- * @bt_params: pointer to bt parameters
- * @pa_type: used by 6000 series only to identify the type of Power Amplifier
- * @need_temp_offset_calib: need to perform temperature offset calibration
- * @no_xtal_calib: some devices do not need crystal calibration data,
- * don't send it to those
- * @scan_antennas: available antenna for scan operation
- * @led_mode: 0=blinking, 1=On(RF On)/Off(RF Off)
- * @adv_pm: advance power management
- * @rx_with_siso_diversity: 1x1 device with rx antenna diversity
- * @internal_wimax_coex: internal wifi/wimax combo device
- * @iq_invert: I/Q inversion
- * @temp_offset_v2: support v2 of temperature offset calibration
- *
- * We enable the driver to be backward compatible wrt API version. The
- * driver specifies which APIs it supports (with @ucode_api_max being the
- * highest and @ucode_api_min the lowest). Firmware will only be loaded if
- * it has a supported API version.
- *
- * The ideal usage of this infrastructure is to treat a new ucode API
- * release as a new hardware revision.
- */
-struct iwl_cfg {
- /* params specific to an individual device within a device family */
- const char *name;
- const char *fw_name_pre;
- const unsigned int ucode_api_max;
- const unsigned int ucode_api_ok;
- const unsigned int ucode_api_min;
- u8 valid_tx_ant;
- u8 valid_rx_ant;
- u16 sku;
- u16 eeprom_ver;
- u16 eeprom_calib_ver;
- const struct iwl_lib_ops *lib;
- void (*additional_nic_config)(struct iwl_priv *priv);
- /* params not likely to change within a device family */
- struct iwl_base_params *base_params;
- /* params likely to change within a device family */
- struct iwl_ht_params *ht_params;
- struct iwl_bt_params *bt_params;
- enum iwl_pa_type pa_type; /* if used set to IWL_PA_SYSTEM */
- const bool need_temp_offset_calib; /* if used set to true */
- const bool no_xtal_calib;
- u8 scan_rx_antennas[IEEE80211_NUM_BANDS];
- enum iwl_led_mode led_mode;
- const bool adv_pm;
- const bool rx_with_siso_diversity;
- const bool internal_wimax_coex;
- const bool iq_invert;
- const bool temp_offset_v2;
-};
-
/***************************
* L i b *
***************************/
static inline bool iwl_advanced_bt_coexist(struct iwl_priv *priv)
{
- return priv->cfg->bt_params &&
- priv->cfg->bt_params->advanced_bt_coexist;
+ return cfg(priv)->bt_params &&
+ cfg(priv)->bt_params->advanced_bt_coexist;
}
static inline void iwl_enable_rfkill_int(struct iwl_priv *priv)