{USB_DEVICE(0x0846, 0x6a00)},
/* HP */
{USB_DEVICE(0x03f0, 0xca02)},
+ /* Sitecom */
+ {USB_DEVICE(0x0df6, 0x000d)},
{}
};
struct rtl8187_tx_hdr *hdr;
struct rtl8187_tx_info *info;
struct urb *urb;
- u32 tmp;
+ __le16 rts_dur = 0;
+ u32 flags;
urb = usb_alloc_urb(0, GFP_ATOMIC);
if (!urb) {
return 0;
}
- hdr = (struct rtl8187_tx_hdr *)skb_push(skb, sizeof(*hdr));
- tmp = skb->len - sizeof(*hdr);
- tmp |= RTL8187_TX_FLAG_NO_ENCRYPT;
- tmp |= control->rts_cts_rate << 19;
- tmp |= control->tx_rate << 24;
- if (ieee80211_get_morefrag((struct ieee80211_hdr *)skb))
- tmp |= RTL8187_TX_FLAG_MORE_FRAG;
+ flags = skb->len;
+ flags |= RTL8187_TX_FLAG_NO_ENCRYPT;
+ flags |= control->rts_cts_rate << 19;
+ flags |= control->tx_rate << 24;
+ if (ieee80211_get_morefrag((struct ieee80211_hdr *)skb->data))
+ flags |= RTL8187_TX_FLAG_MORE_FRAG;
if (control->flags & IEEE80211_TXCTL_USE_RTS_CTS) {
- tmp |= RTL8187_TX_FLAG_RTS;
- hdr->rts_duration =
- ieee80211_rts_duration(dev, priv->if_id, skb->len, control);
+ flags |= RTL8187_TX_FLAG_RTS;
+ rts_dur = ieee80211_rts_duration(dev, priv->vif,
+ skb->len, control);
}
if (control->flags & IEEE80211_TXCTL_USE_CTS_PROTECT)
- tmp |= RTL8187_TX_FLAG_CTS;
- hdr->flags = cpu_to_le32(tmp);
+ flags |= RTL8187_TX_FLAG_CTS;
+
+ hdr = (struct rtl8187_tx_hdr *)skb_push(skb, sizeof(*hdr));
+ hdr->flags = cpu_to_le32(flags);
hdr->len = 0;
- tmp = control->retry_limit << 8;
- hdr->retry = cpu_to_le32(tmp);
+ hdr->rts_duration = rts_dur;
+ hdr->retry = cpu_to_le32(control->retry_limit << 8);
info = (struct rtl8187_tx_info *)skb->cb;
info->control = kmemdup(control, sizeof(*control), GFP_ATOMIC);
rx_status.channel = dev->conf.channel;
rx_status.phymode = dev->conf.phymode;
rx_status.mactime = le64_to_cpu(hdr->mac_time);
+ rx_status.flag |= RX_FLAG_TSFT;
if (flags & (1 << 13))
rx_status.flag |= RX_FLAG_FAILED_FCS_CRC;
ieee80211_rx_irqsafe(dev, skb, &rx_status);
rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FF7);
msleep(100);
- priv->rf_init(dev);
+ priv->rf->init(dev);
rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3);
- reg = rtl818x_ioread16(priv, &priv->map->PGSELECT) & 0xfffe;
- rtl818x_iowrite16(priv, &priv->map->PGSELECT, reg | 0x1);
+ reg = rtl818x_ioread8(priv, &priv->map->PGSELECT) & ~1;
+ rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg | 1);
rtl818x_iowrite16(priv, (__le16 *)0xFFFE, 0x10);
rtl818x_iowrite8(priv, &priv->map->TALLY_SEL, 0x80);
rtl818x_iowrite8(priv, (u8 *)0xFFFF, 0x60);
- rtl818x_iowrite16(priv, &priv->map->PGSELECT, reg);
+ rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg);
return 0;
}
-static void rtl8187_set_channel(struct ieee80211_hw *dev, int channel)
-{
- u32 reg;
- struct rtl8187_priv *priv = dev->priv;
-
- reg = rtl818x_ioread32(priv, &priv->map->TX_CONF);
- /* Enable TX loopback on MAC level to avoid TX during channel
- * changes, as this has be seen to causes problems and the
- * card will stop work until next reset
- */
- rtl818x_iowrite32(priv, &priv->map->TX_CONF,
- reg | RTL818X_TX_CONF_LOOPBACK_MAC);
- msleep(10);
- rtl8225_rf_set_channel(dev, channel);
- msleep(10);
- rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg);
-}
-
static int rtl8187_start(struct ieee80211_hw *dev)
{
struct rtl8187_priv *priv = dev->priv;
rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF);
+ rtl818x_iowrite32(priv, &priv->map->MAR[0], ~0);
+ rtl818x_iowrite32(priv, &priv->map->MAR[1], ~0);
+
rtl8187_init_urbs(dev);
reg = RTL818X_RX_CONF_ONLYERLPKT |
reg &= ~RTL818X_CMD_RX_ENABLE;
rtl818x_iowrite8(priv, &priv->map->CMD, reg);
- rtl8225_rf_stop(dev);
+ priv->rf->stop(dev);
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
reg = rtl818x_ioread8(priv, &priv->map->CONFIG4);
static int rtl8187_config(struct ieee80211_hw *dev, struct ieee80211_conf *conf)
{
struct rtl8187_priv *priv = dev->priv;
- rtl8187_set_channel(dev, conf->channel);
+ u32 reg;
+
+ reg = rtl818x_ioread32(priv, &priv->map->TX_CONF);
+ /* Enable TX loopback on MAC level to avoid TX during channel
+ * changes, as this has be seen to causes problems and the
+ * card will stop work until next reset
+ */
+ rtl818x_iowrite32(priv, &priv->map->TX_CONF,
+ reg | RTL818X_TX_CONF_LOOPBACK_MAC);
+ msleep(10);
+ priv->rf->set_chan(dev, conf);
+ msleep(10);
+ rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg);
rtl818x_iowrite8(priv, &priv->map->SIFS, 0x22);
return 0;
}
-static int rtl8187_config_interface(struct ieee80211_hw *dev, int if_id,
+static int rtl8187_config_interface(struct ieee80211_hw *dev,
+ struct ieee80211_vif *vif,
struct ieee80211_if_conf *conf)
{
struct rtl8187_priv *priv = dev->priv;
int i;
- priv->if_id = if_id;
-
for (i = 0; i < ETH_ALEN; i++)
rtl818x_iowrite8(priv, &priv->map->BSSID[i], conf->bssid[i]);
static void rtl8187_configure_filter(struct ieee80211_hw *dev,
unsigned int changed_flags,
unsigned int *total_flags,
- int mc_count, struct dev_addr_list *mc_list)
+ int mc_count, struct dev_addr_list *mclist)
{
struct rtl8187_priv *priv = dev->priv;
- *total_flags = 0;
-
- if (changed_flags & FIF_PROMISC_IN_BSS)
- priv->rx_conf ^= RTL818X_RX_CONF_NICMAC;
- if (changed_flags & FIF_ALLMULTI)
- priv->rx_conf ^= RTL818X_RX_CONF_MULTICAST;
if (changed_flags & FIF_FCSFAIL)
priv->rx_conf ^= RTL818X_RX_CONF_FCS;
if (changed_flags & FIF_CONTROL)
priv->rx_conf ^= RTL818X_RX_CONF_CTRL;
if (changed_flags & FIF_OTHER_BSS)
priv->rx_conf ^= RTL818X_RX_CONF_MONITOR;
-
- if (mc_count > 0)
+ if (*total_flags & FIF_ALLMULTI || mc_count > 0)
priv->rx_conf |= RTL818X_RX_CONF_MULTICAST;
+ else
+ priv->rx_conf &= ~RTL818X_RX_CONF_MULTICAST;
+
+ *total_flags = 0;
- if (priv->rx_conf & RTL818X_RX_CONF_NICMAC)
- *total_flags |= FIF_PROMISC_IN_BSS;
- if (priv->rx_conf & RTL818X_RX_CONF_MULTICAST)
- *total_flags |= FIF_ALLMULTI;
if (priv->rx_conf & RTL818X_RX_CONF_FCS)
*total_flags |= FIF_FCSFAIL;
if (priv->rx_conf & RTL818X_RX_CONF_CTRL)
*total_flags |= FIF_CONTROL;
if (priv->rx_conf & RTL818X_RX_CONF_MONITOR)
*total_flags |= FIF_OTHER_BSS;
+ if (priv->rx_conf & RTL818X_RX_CONF_MULTICAST)
+ *total_flags |= FIF_ALLMULTI;
rtl818x_iowrite32_async(priv, &priv->map->RX_CONF, priv->rx_conf);
}
eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_BASE,
&priv->txpwr_base);
- reg = rtl818x_ioread16(priv, &priv->map->PGSELECT) & ~1;
- rtl818x_iowrite16(priv, &priv->map->PGSELECT, reg | 1);
+ reg = rtl818x_ioread8(priv, &priv->map->PGSELECT) & ~1;
+ rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg | 1);
/* 0 means asic B-cut, we should use SW 3 wire
* bit-by-bit banging for radio. 1 means we can use
* USB specific request to write radio registers */
priv->asic_rev = rtl818x_ioread8(priv, (u8 *)0xFFFE) & 0x3;
- rtl818x_iowrite16(priv, &priv->map->PGSELECT, reg);
+ rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg);
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
- rtl8225_write(dev, 0, 0x1B7);
-
- if (rtl8225_read(dev, 8) != 0x588 || rtl8225_read(dev, 9) != 0x700)
- priv->rf_init = rtl8225_rf_init;
- else
- priv->rf_init = rtl8225z2_rf_init;
-
- rtl8225_write(dev, 0, 0x0B7);
+ priv->rf = rtl8187_detect_rf(dev);
err = ieee80211_register_hw(dev);
if (err) {
printk(KERN_INFO "%s: hwaddr %s, rtl8187 V%d + %s\n",
wiphy_name(dev->wiphy), print_mac(mac, dev->wiphy->perm_addr),
- priv->asic_rev, priv->rf_init == rtl8225_rf_init ?
- "rtl8225" : "rtl8225z2");
+ priv->asic_rev, priv->rf->name);
return 0;