}
}
+ if (rdev->constraints->ramp_delay && ops->set_ramp_delay) {
+ ret = ops->set_ramp_delay(rdev, rdev->constraints->ramp_delay);
+ if (ret < 0) {
+ rdev_err(rdev, "failed to set ramp_delay\n");
+ goto out;
+ }
+ }
+
print_constraints(rdev);
return 0;
out:
{
int rc;
- rc = devres_destroy(regulator->dev, devm_regulator_release,
+ rc = devres_release(regulator->dev, devm_regulator_release,
devm_regulator_match, regulator);
if (rc == 0)
regulator_put(regulator);
}
EXPORT_SYMBOL_GPL(regulator_list_voltage_linear);
+/**
+ * regulator_list_voltage_table - List voltages with table based mapping
+ *
+ * @rdev: Regulator device
+ * @selector: Selector to convert into a voltage
+ *
+ * Regulators with table based mapping between voltages and
+ * selectors can set volt_table in the regulator descriptor
+ * and then use this function as their list_voltage() operation.
+ */
+int regulator_list_voltage_table(struct regulator_dev *rdev,
+ unsigned int selector)
+{
+ if (!rdev->desc->volt_table) {
+ BUG_ON(!rdev->desc->volt_table);
+ return -EINVAL;
+ }
+
+ if (selector >= rdev->desc->n_voltages)
+ return -EINVAL;
+
+ return rdev->desc->volt_table[selector];
+}
+EXPORT_SYMBOL_GPL(regulator_list_voltage_table);
+
/**
* regulator_list_voltage - enumerate supported voltages
* @regulator: regulator source
{
int ret, voltage;
+ /* Allow uV_step to be 0 for fixed voltage */
+ if (rdev->desc->n_voltages == 1 && rdev->desc->uV_step == 0) {
+ if (min_uV <= rdev->desc->min_uV && rdev->desc->min_uV <= max_uV)
+ return 0;
+ else
+ return -EINVAL;
+ }
+
if (!rdev->desc->uV_step) {
BUG_ON(!rdev->desc->uV_step);
return -EINVAL;
* If we can't obtain the old selector there is not enough
* info to call set_voltage_time_sel().
*/
- if (rdev->desc->ops->set_voltage_time_sel &&
+ if (_regulator_is_enabled(rdev) &&
+ rdev->desc->ops->set_voltage_time_sel &&
rdev->desc->ops->get_voltage_sel) {
old_selector = rdev->desc->ops->get_voltage_sel(rdev);
if (old_selector < 0)
best_val = -1;
/* Call set_voltage_time_sel if successfully obtained old_selector */
- if (ret == 0 && old_selector >= 0 &&
+ if (_regulator_is_enabled(rdev) && ret == 0 && old_selector >= 0 &&
rdev->desc->ops->set_voltage_time_sel) {
delay = rdev->desc->ops->set_voltage_time_sel(rdev,
}
EXPORT_SYMBOL_GPL(regulator_set_voltage_time);
+/**
+ *regulator_set_voltage_time_sel - get raise/fall time
+ * @regulator: regulator source
+ * @old_selector: selector for starting voltage
+ * @new_selector: selector for target voltage
+ *
+ * Provided with the starting and target voltage selectors, this function
+ * returns time in microseconds required to rise or fall to this new voltage
+ *
+ * Drivers providing ramp_delay in regulation_constraints can use this as their
+ * set_voltage_time_sel() operation.
+ */
+int regulator_set_voltage_time_sel(struct regulator_dev *rdev,
+ unsigned int old_selector,
+ unsigned int new_selector)
+{
+ unsigned int ramp_delay = 0;
+ int old_volt, new_volt;
+
+ if (rdev->constraints->ramp_delay)
+ ramp_delay = rdev->constraints->ramp_delay;
+ else if (rdev->desc->ramp_delay)
+ ramp_delay = rdev->desc->ramp_delay;
+
+ if (ramp_delay == 0) {
+ rdev_warn(rdev, "ramp_delay not set\n");
+ return 0;
+ }
+
+ /* sanity check */
+ if (!rdev->desc->ops->list_voltage)
+ return -EINVAL;
+
+ old_volt = rdev->desc->ops->list_voltage(rdev, old_selector);
+ new_volt = rdev->desc->ops->list_voltage(rdev, new_selector);
+
+ return DIV_ROUND_UP(abs(new_volt - old_volt), ramp_delay);
+}
+EXPORT_SYMBOL_GPL(regulator_set_voltage_time_sel);
+
/**
* regulator_sync_voltage - re-apply last regulator output voltage
* @regulator: regulator source
rdev->reg_data = config->driver_data;
rdev->owner = regulator_desc->owner;
rdev->desc = regulator_desc;
- rdev->regmap = config->regmap;
+ if (config->regmap)
+ rdev->regmap = config->regmap;
+ else
+ rdev->regmap = dev_get_regmap(dev, NULL);
INIT_LIST_HEAD(&rdev->consumer_list);
INIT_LIST_HEAD(&rdev->list);
BLOCKING_INIT_NOTIFIER_HEAD(&rdev->notifier);