[SCSI] qla2xxx: Add ISP25XX support.

[deliverable/linux.git] / drivers / scsi / qla2xxx / qla_fw.h

diff --git a/drivers/scsi/qla2xxx/qla_fw.h b/drivers/scsi/qla2xxx/qla_fw.h
index 63a11fef5d1bcf8d048bc0f6d6056b9ab9f8fcc9..99fe49618d6134c5342478755e701ac4d6f32b76 100644 (file)
--- a/drivers/scsi/qla2xxx/qla_fw.h
+++ b/drivers/scsi/qla2xxx/qla_fw.h
@@ -8,14 +8,17 @@
 #define __QLA_FW_H
 
 #define MBS_CHECKSUM_ERROR     0x4010
+#define MBS_INVALID_PRODUCT_KEY        0x4020
 
 /*
  * Firmware Options.
  */
 #define FO1_ENABLE_PUREX       BIT_10
 #define FO1_DISABLE_LED_CTRL   BIT_6
+#define FO1_ENABLE_8016                BIT_0
 #define FO2_ENABLE_SEL_CLASS2  BIT_5
 #define FO3_NO_ABTS_ON_LINKDOWN        BIT_14
+#define FO3_HOLD_STS_IOCB      BIT_12
 
 /*
  * Port Database structure definition for ISP 24xx.
@@ -341,7 +344,9 @@ struct init_cb_24xx {
         * BIT 10 = Reserved
         * BIT 11 = Enable FC-SP Security
         * BIT 12 = FC Tape Enable
-        * BIT 13-31 = Reserved
+        * BIT 13 = Reserved
+        * BIT 14 = Enable Target PRLI Control
+        * BIT 15-31 = Reserved
         */
        uint32_t firmware_options_2;
 
@@ -363,7 +368,8 @@ struct init_cb_24xx {
         * BIT 13 = Data Rate bit 0
         * BIT 14 = Data Rate bit 1
         * BIT 15 = Data Rate bit 2
-        * BIT 16-31 = Reserved
+        * BIT 16 = Enable 75 ohm Termination Select
+        * BIT 17-31 = Reserved
         */
        uint32_t firmware_options_3;
 
@@ -435,6 +441,7 @@ struct cmd_type_7 {
 #define TMF_LUN_RESET          BIT_12
 #define TMF_CLEAR_TASK_SET     BIT_10
 #define TMF_ABORT_TASK_SET     BIT_9
+#define TMF_DSD_LIST_ENABLE    BIT_2
 #define TMF_READ_DATA          BIT_1
 #define TMF_WRITE_DATA         BIT_0
 
@@ -589,7 +596,7 @@ struct els_entry_24xx {
 #define EST_SOFI3              (1 << 4)
 #define EST_SOFI2              (3 << 4)
 
-       uint32_t rx_xchg_address[2];    /* Receive exchange address. */
+       uint32_t rx_xchg_address;       /* Receive exchange address. */
        uint16_t rx_dsd_count;
 
        uint8_t opcode;
@@ -650,6 +657,7 @@ struct logio_entry_24xx {
 
        uint16_t control_flags;         /* Control flags. */
                                        /* Modifiers. */
+#define LCF_INCLUDE_SNS                BIT_10  /* Include SNS (FFFFFC) during LOGO. */
 #define LCF_FCP2_OVERRIDE      BIT_9   /* Set/Reset word 3 of PRLI. */
 #define LCF_CLASS_2            BIT_8   /* Enable class 2 during PLOGI. */
 #define LCF_FREE_NPORT         BIT_7   /* Release NPORT handle after LOGO. */
@@ -779,6 +787,15 @@ struct device_reg_24xx {
 #define FA_RISC_CODE_ADDR      0x20000
 #define FA_RISC_CODE_SEGMENTS  2
 
+#define FA_FW_AREA_ADDR                0x40000
+#define FA_VPD_NVRAM_ADDR      0x48000
+#define FA_FEATURE_ADDR                0x4C000
+#define FA_FLASH_DESCR_ADDR    0x50000
+#define FA_HW_EVENT_ADDR       0x54000
+#define FA_BOOT_LOG_ADDR       0x58000
+#define FA_FW_DUMP0_ADDR       0x60000
+#define FA_FW_DUMP1_ADDR       0x70000
+
        uint32_t flash_data;            /* Flash/NVRAM BIOS data. */
 
        uint32_t ctrl_status;           /* Control/Status. */
@@ -859,10 +876,13 @@ struct device_reg_24xx {
 #define HCCRX_CLR_RISC_INT     0xA0000000
 
        uint32_t gpiod;                 /* GPIO Data register. */
+
                                        /* LED update mask. */
 #define GPDX_LED_UPDATE_MASK   (BIT_20|BIT_19|BIT_18)
                                        /* Data update mask. */
 #define GPDX_DATA_UPDATE_MASK  (BIT_17|BIT_16)
+                                       /* Data update mask. */
+#define GPDX_DATA_UPDATE_2_MASK        (BIT_28|BIT_27|BIT_26|BIT_17|BIT_16)
                                        /* LED control mask. */
 #define GPDX_LED_COLOR_MASK    (BIT_4|BIT_3|BIT_2)
                                        /* LED bit values. Color names as
@@ -877,6 +897,8 @@ struct device_reg_24xx {
        uint32_t gpioe;                 /* GPIO Enable register. */
                                        /* Enable update mask. */
 #define GPEX_ENABLE_UPDATE_MASK        (BIT_17|BIT_16)
+                                       /* Enable update mask. */
+#define GPEX_ENABLE_UPDATE_2_MASK (BIT_28|BIT_27|BIT_26|BIT_17|BIT_16)
                                        /* Enable. */
 #define GPEX_ENABLE            (BIT_1|BIT_0)
 
@@ -916,6 +938,14 @@ struct device_reg_24xx {
        uint16_t mailbox29;
        uint16_t mailbox30;
        uint16_t mailbox31;
+
+       uint32_t iobase_window;
+       uint32_t unused_4[8];           /* Gap. */
+       uint32_t iobase_q;
+       uint32_t unused_5[2];           /* Gap. */
+       uint32_t iobase_select;
+       uint32_t unused_6[2];           /* Gap. */
+       uint32_t iobase_sdata;
 };
 
 /* MID Support ***************************************************************/