* handshake done). There are two failure modes: "usec" have passed (major
* hardware flakeout), or the register reads as all-ones (hardware removed).
*/
-static int handshake(struct xhci_hcd *xhci, void __iomem *ptr,
+int handshake(struct xhci_hcd *xhci, void __iomem *ptr,
u32 mask, u32 done, int usec)
{
u32 result;
ret = handshake(xhci, &xhci->op_regs->status,
STS_HALT, STS_HALT, XHCI_MAX_HALT_USEC);
- if (!ret)
+ if (!ret) {
xhci->xhc_state |= XHCI_STATE_HALTED;
- else
+ xhci->cmd_ring_state = CMD_RING_STATE_STOPPED;
+ } else
xhci_warn(xhci, "Host not halted after %u microseconds.\n",
XHCI_MAX_HALT_USEC);
return ret;
return -ENODEV;
}
xhci->shared_hcd->state = HC_STATE_RUNNING;
+ xhci->cmd_ring_state = CMD_RING_STATE_RUNNING;
if (xhci->quirks & XHCI_NEC_HOST)
xhci_ring_cmd_db(xhci);
struct completion *cmd_completion;
u32 *cmd_status;
struct xhci_virt_device *virt_dev;
+ union xhci_trb *cmd_trb;
spin_lock_irqsave(&xhci->lock, flags);
virt_dev = xhci->devs[udev->slot_id];
}
init_completion(cmd_completion);
+ cmd_trb = xhci->cmd_ring->dequeue;
if (!ctx_change)
ret = xhci_queue_configure_endpoint(xhci, in_ctx->dma,
udev->slot_id, must_succeed);
/* Wait for the configure endpoint command to complete */
timeleft = wait_for_completion_interruptible_timeout(
cmd_completion,
- USB_CTRL_SET_TIMEOUT);
+ XHCI_CMD_DEFAULT_TIMEOUT);
if (timeleft <= 0) {
xhci_warn(xhci, "%s while waiting for %s command\n",
timeleft == 0 ? "Timeout" : "Signal",
ctx_change == 0 ?
"configure endpoint" :
"evaluate context");
- /* FIXME cancel the configure endpoint command */
+ /* cancel the configure endpoint command */
+ ret = xhci_cancel_cmd(xhci, command, cmd_trb);
+ if (ret < 0)
+ return ret;
return -ETIME;
}
unsigned long flags;
int timeleft;
int ret;
+ union xhci_trb *cmd_trb;
spin_lock_irqsave(&xhci->lock, flags);
+ cmd_trb = xhci->cmd_ring->dequeue;
ret = xhci_queue_slot_control(xhci, TRB_ENABLE_SLOT, 0);
if (ret) {
spin_unlock_irqrestore(&xhci->lock, flags);
/* XXX: how much time for xHC slot assignment? */
timeleft = wait_for_completion_interruptible_timeout(&xhci->addr_dev,
- USB_CTRL_SET_TIMEOUT);
+ XHCI_CMD_DEFAULT_TIMEOUT);
if (timeleft <= 0) {
xhci_warn(xhci, "%s while waiting for a slot\n",
timeleft == 0 ? "Timeout" : "Signal");
- /* FIXME cancel the enable slot request */
- return 0;
+ /* cancel the enable slot request */
+ return xhci_cancel_cmd(xhci, NULL, cmd_trb);
}
if (!xhci->slot_id) {
struct xhci_slot_ctx *slot_ctx;
struct xhci_input_control_ctx *ctrl_ctx;
u64 temp_64;
+ union xhci_trb *cmd_trb;
if (!udev->slot_id) {
xhci_dbg(xhci, "Bad Slot ID %d\n", udev->slot_id);
xhci_dbg_ctx(xhci, virt_dev->in_ctx, 2);
spin_lock_irqsave(&xhci->lock, flags);
+ cmd_trb = xhci->cmd_ring->dequeue;
ret = xhci_queue_address_device(xhci, virt_dev->in_ctx->dma,
udev->slot_id);
if (ret) {
/* ctrl tx can take up to 5 sec; XXX: need more time for xHC? */
timeleft = wait_for_completion_interruptible_timeout(&xhci->addr_dev,
- USB_CTRL_SET_TIMEOUT);
+ XHCI_CMD_DEFAULT_TIMEOUT);
/* FIXME: From section 4.3.4: "Software shall be responsible for timing
* the SetAddress() "recovery interval" required by USB and aborting the
* command on a timeout.
if (timeleft <= 0) {
xhci_warn(xhci, "%s while waiting for address device command\n",
timeleft == 0 ? "Timeout" : "Signal");
- /* FIXME cancel the address device command */
+ /* cancel the address device command */
+ ret = xhci_cancel_cmd(xhci, NULL, cmd_trb);
+ if (ret < 0)
+ return ret;
return -ETIME;
}