What has changed in GDB?
(Organized release by release)
-*** Changes since GDB 7.7
+*** Changes since GDB 7.8
+
+*** Changes in GDB 7.8
+
+* New command line options
+
+-D data-directory
+ This is an alias for the --data-directory option.
+
+* GDB supports printing and modifying of variable length automatic arrays
+ as specified in ISO C99.
+
+* The ARM simulator now supports instruction level tracing
+ with or without disassembly.
+
+* Guile scripting
+
+ GDB now has support for scripting using Guile. Whether this is
+ available is determined at configure time.
+ Guile version 2.0 or greater is required.
+ Guile version 2.0.9 is well tested, earlier 2.0 versions are not.
+
+* New commands (for set/show, see "New options" below)
+
+guile [code]
+gu [code]
+ Invoke CODE by passing it to the Guile interpreter.
+
+guile-repl
+gr
+ Start a Guile interactive prompt (or "repl" for "read-eval-print loop").
+
+info auto-load guile-scripts [regexp]
+ Print the list of automatically loaded Guile scripts.
+
+* The source command is now capable of sourcing Guile scripts.
+ This feature is dependent on the debugger being built with Guile support.
+
+* New options
+
+set print symbol-loading (off|brief|full)
+show print symbol-loading
+ Control whether to print informational messages when loading symbol
+ information for a file. The default is "full", but when debugging
+ programs with large numbers of shared libraries the amount of output
+ becomes less useful.
+
+set guile print-stack (none|message|full)
+show guile print-stack
+ Show a stack trace when an error is encountered in a Guile script.
+
+set auto-load guile-scripts (on|off)
+show auto-load guile-scripts
+ Control auto-loading of Guile script files.
+
+maint ada set ignore-descriptive-types (on|off)
+maint ada show ignore-descriptive-types
+ Control whether the debugger should ignore descriptive types in Ada
+ programs. The default is not to ignore the descriptive types. See
+ the user manual for more details on descriptive types and the intended
+ usage of this option.
+
+set auto-connect-native-target
+
+ Control whether GDB is allowed to automatically connect to the
+ native target for the run, attach, etc. commands when not connected
+ to any target yet. See also "target native" below.
+
+set record btrace replay-memory-access (read-only|read-write)
+show record btrace replay-memory-access
+ Control what memory accesses are allowed during replay.
+
+maint set target-async (on|off)
+maint show target-async
+ This controls whether GDB targets operate in syncronous or
+ asyncronous mode. Normally the default is asyncronous, if it is
+ available; but this can be changed to more easily debug problems
+ occurring only in syncronous mode.
+
+set mi-async (on|off)
+show mi-async
+ Control whether MI asynchronous mode is preferred. This supersedes
+ "set target-async" of previous GDB versions.
+
+* "set target-async" is deprecated as a CLI option and is now an alias
+ for "set mi-async" (only puts MI into async mode).
+
+* Background execution commands (e.g., "c&", "s&", etc.) are now
+ possible ``out of the box'' if the target supports them. Previously
+ the user would need to explicitly enable the possibility with the
+ "set target-async on" command.
+
+* New features in the GDB remote stub, GDBserver
+
+ ** New option --debug-format=option1[,option2,...] allows one to add
+ additional text to each output. At present only timestamps
+ are supported: --debug-format=timestamps.
+ Timestamps can also be turned on with the
+ "monitor set debug-format timestamps" command from GDB.
* The 'record instruction-history' command now starts counting instructions
at one. This also affects the instruction ranges reported by the
For locations inside the execution trace, the back trace is computed
based on the information stored in the execution trace.
+* The btrace record target supports limited reverse execution and replay.
+ The target does not record data and therefore does not allow reading
+ memory or registers.
+
+* The "catch syscall" command now works on s390*-linux* targets.
+
+* The "compare-sections" command is no longer specific to target
+ remote. It now works with all targets.
+
+* All native targets are now consistently called "native".
+ Consequently, the "target child", "target GNU", "target djgpp",
+ "target procfs" (Solaris/Irix/OSF/AIX) and "target darwin-child"
+ commands have been replaced with "target native". The QNX/NTO port
+ leaves the "procfs" target in place and adds a "native" target for
+ consistency with other ports. The impact on users should be minimal
+ as these commands previously either throwed an error, or were
+ no-ops. The target's name is visible in the output of the following
+ commands: "help target", "info target", "info files", "maint print
+ target-stack".
+
+* The "target native" command now connects to the native target. This
+ can be used to launch native programs even when "set
+ auto-connect-native-target" is set to off.
+
* New remote packets
qXfer:btrace:read's annex
The qXfer:btrace:read packet supports a new annex 'delta' to read
branch trace incrementally.
+* Python Scripting
+
+ ** Valid Python operations on gdb.Value objects representing
+ structs/classes invoke the corresponding overloaded operators if
+ available.
+ ** New `Xmethods' feature in the Python API. Xmethods are
+ additional methods or replacements for existing methods of a C++
+ class. This feature is useful for those cases where a method
+ defined in C++ source code could be inlined or optimized out by
+ the compiler, making it unavailable to GDB.
+
+* New targets
+PowerPC64 GNU/Linux little-endian powerpc64le-*-linux*
+
+* The "dll-symbols" command, and its two aliases ("add-shared-symbol-files"
+ and "assf"), have been deprecated. Use the "sharedlibrary" command, or
+ its alias "share", instead.
+
+* The commands "set remotebaud" and "show remotebaud" are no longer
+ supported. Use "set serial baud" and "show serial baud" (respectively)
+ instead.
+
+* MI changes
+
+ ** A new option "-gdb-set mi-async" replaces "-gdb-set
+ target-async". The latter is left as a deprecated alias of the
+ former for backward compatibility. If the target supports it,
+ CLI background execution commands are now always possible by
+ default, independently of whether the frontend stated a
+ preference for asynchronous execution with "-gdb-set mi-async".
+ Previously "-gdb-set target-async off" affected both MI execution
+ commands and CLI execution commands.
+
*** Changes in GDB 7.7
* Improved support for process record-replay and reverse debugging on
where the program that you are debugging will run.
* GDB now supports access to Intel(R) MPX registers on GNU/Linux.
+
+ * Support for Intel(R) AVX-512 registers on GNU/Linux.
+
+Support displaying and modifying Intel(R) AVX-512 registers $zmm0 - $zmm31 and
+$k0 - $k7 on GNU/Linux.
projects / deliverable / binutils-gdb.git / blobdiff