/* Dynamic architecture support for GDB, the GNU debugger.
- Copyright 1998, 1999, 2000, 2001 Free Software Foundation, Inc.
+
+ Copyright 1998, 1999, 2000, 2001, 2002 Free Software Foundation,
+ Inc.
This file is part of GDB.
and optionally adjust the pc to point to the correct memory location
for inserting the breakpoint. */
-unsigned char *
+const unsigned char *
legacy_breakpoint_from_pc (CORE_ADDR * pcptr, int *lenptr)
{
/* {BIG_,LITTLE_}BREAKPOINT is the sequence of bytes we insert for a
int
generic_prologue_frameless_p (CORE_ADDR ip)
{
-#ifdef SKIP_PROLOGUE_FRAMELESS_P
- return ip == SKIP_PROLOGUE_FRAMELESS_P (ip);
-#else
return ip == SKIP_PROLOGUE (ip);
-#endif
}
/* New/multi-arched targets should use the correct gdbarch field
}
}
+void
+default_print_float_info (void)
+{
+#ifdef FLOAT_INFO
+#if GDB_MULTI_ARCH > GDB_MULTI_ARCH_PARTIAL
+#error "FLOAT_INFO defined in multi-arch"
+#endif
+ FLOAT_INFO;
+#else
+ printf_filtered ("No floating point info available for this processor.\n");
+#endif
+}
+
/* Misc helper functions for targets. */
int
flush_cached_frames ();
registers_changed ();
stop_pc = wait_pc;
- select_frame (get_current_frame (), 0);
+ select_frame (get_current_frame ());
}
/* We return 1 to indicate that there is a breakpoint here,
so we need to step over it before continuing to avoid
prev->pc = read_pc ();
}
+void
+default_elf_make_msymbol_special (asymbol *sym, struct minimal_symbol *msym)
+{
+ return;
+}
+
+void
+default_coff_make_msymbol_special (int val, struct minimal_symbol *msym)
+{
+ return;
+}
+
int
cannot_register_not (int regnum)
{
*frame_offset = 0;
}
-/* Assume the world is flat. Every register is large enough to fit a
- target integer. */
+/* Assume the world is sane, every register's virtual and real size
+ is identical. */
int
-generic_register_raw_size (int regnum)
+generic_register_size (int regnum)
{
gdb_assert (regnum >= 0 && regnum < NUM_REGS + NUM_PSEUDO_REGS);
- return TARGET_INT_BIT / HOST_CHAR_BIT;
+ return TYPE_LENGTH (REGISTER_VIRTUAL_TYPE (regnum));
}
-/* Assume the virtual size corresponds to the virtual type. */
+#if !defined (IN_SIGTRAMP)
+#if defined (SIGTRAMP_START)
+#define IN_SIGTRAMP(pc, name) \
+ ((pc) >= SIGTRAMP_START(pc) \
+ && (pc) < SIGTRAMP_END(pc) \
+ )
+#else
+#define IN_SIGTRAMP(pc, name) \
+ (name && STREQ ("_sigtramp", name))
+#endif
+#endif
+\f
+int
+legacy_pc_in_sigtramp (CORE_ADDR pc, char *name)
+{
+ return IN_SIGTRAMP(pc, name);
+}
int
-generic_register_virtual_size (int regnum)
+legacy_convert_register_p (int regnum)
{
- return TYPE_LENGTH (REGISTER_VIRTUAL_TYPE (regnum));
+ return REGISTER_CONVERTIBLE (regnum);
+}
+
+void
+legacy_register_to_value (int regnum, struct type *type,
+ char *from, char *to)
+{
+ REGISTER_CONVERT_TO_VIRTUAL (regnum, type, from, to);
+}
+
+void
+legacy_value_to_register (struct type *type, int regnum,
+ char *from, char *to)
+{
+ REGISTER_CONVERT_TO_RAW (type, regnum, from, to);
}
\f
/* Functions to manipulate the endianness of the target. */
-#ifndef TARGET_BYTE_ORDER_DEFAULT
-#define TARGET_BYTE_ORDER_DEFAULT BFD_ENDIAN_BIG /* arbitrary */
-#endif
/* ``target_byte_order'' is only used when non- multi-arch.
- Multi-arch targets obtain the current byte order using
- TARGET_BYTE_ORDER which is controlled by gdbarch.*. */
-int target_byte_order = TARGET_BYTE_ORDER_DEFAULT;
+ Multi-arch targets obtain the current byte order using the
+ TARGET_BYTE_ORDER gdbarch method.
+
+ The choice of initial value is entirely arbitrary. During startup,
+ the function initialize_current_architecture() updates this value
+ based on default byte-order information extracted from BFD. */
+int target_byte_order = BFD_ENDIAN_BIG;
int target_byte_order_auto = 1;
static const char endian_big[] = "big";
"initialize_current_architecture: Arch not found");
}
- /* take several guesses at a byte order. */
- /* NB: can't use TARGET_BYTE_ORDER_DEFAULT as its definition is
- forced above. */
+ /* Take several guesses at a byte order. */
if (info.byte_order == BFD_ENDIAN_UNKNOWN
&& default_bfd_vec != NULL)
{
}
}
else
- initialize_non_multiarch ();
+ {
+ /* If the multi-arch logic comes up with a byte-order (from BFD)
+ use it for the non-multi-arch case. */
+ if (info.byte_order != BFD_ENDIAN_UNKNOWN)
+ target_byte_order = info.byte_order;
+ initialize_non_multiarch ();
+ }
/* Create the ``set architecture'' command appending ``auto'' to the
list of architectures. */
arches, &set_architecture_string,
"Set architecture of target.",
&setlist);
- c->function.sfunc = set_architecture;
+ set_cmd_sfunc (c, set_architecture);
add_alias_cmd ("processor", "architecture", class_support, 1, &setlist);
/* Don't use set_from_show - need to print both auto/manual and
current setting. */
endian_enum, &set_endian_string,
"Set endianness of target.",
&setlist);
- c->function.sfunc = set_endian;
+ set_cmd_sfunc (c, set_endian);
/* Don't use set_from_show - need to print both auto/manual and
current setting. */
add_cmd ("endian", class_support, show_endian,
projects / deliverable / binutils-gdb.git / blobdiff