Software Foundation raise funds for GNU development.''
@end titlepage
-@c TeX can handle the contents at the start but makeinfo 3.12 can not
-@iftex
@contents
-@end iftex
@node Top
@c Perhaps this should be the title of the document (but only for info,
@chapter Host Definition
-@emph{Maintainer's note: In theory, new targets no longer need to use
-the host framework described below. Instead it should be possible to
-handle everything using autoconf. Patches eliminating this framework
-welcome.}
-
With the advent of Autoconf, it's rarely necessary to have host
-definition machinery anymore.
+definition machinery anymore. The following information is provided,
+mainly, as an historical reference.
@section Adding a New Host
@cindex adding a new host
@cindex host, adding
-Most of @value{GDBN}'s host configuration support happens via
-Autoconf. New host-specific definitions should be rarely needed.
-@value{GDBN} still uses the host-specific definitions and files listed
-below, but these mostly exist for historical reasons, and should
+@value{GDBN}'s host configuration support normally happens via Autoconf.
+New host-specific definitions should not be needed. Older hosts
+@value{GDBN} still use the host-specific definitions and files listed
+below, but these mostly exist for historical reasons, and will
eventually disappear.
-Several files control @value{GDBN}'s configuration for host systems:
-
@table @file
@item gdb/config/@var{arch}/@var{xyz}.mh
-Specifies Makefile fragments needed when hosting on machine @var{xyz}.
-Optionally specifies the header file which describes host @var{xyz}, by
-defining @code{XM_FILE= xm-@var{xyz}.h}. You can also define @code{CC},
+This file once contained both host and native configuration information
+(@pxref{Native Debugging}) for the machine @var{xyz}. The host
+configuration information is now handed by Autoconf.
+
+Host configuration information included a definition of
+@code{XM_FILE=xm-@var{xyz}.h} and possibly definitions for @code{CC},
@code{SYSV_DEFINE}, @code{XM_CFLAGS}, @code{XM_ADD_FILES},
@code{XM_CLIBS}, @code{XM_CDEPS}, etc.; see @file{Makefile.in}.
+New host only configurations do not need this file.
+
@item gdb/config/@var{arch}/xm-@var{xyz}.h
-(@file{xm.h} is a link to this file, created by @code{configure}). Contains C
-macro definitions describing the host system environment, such as byte
-order, host C compiler and library.
+This file once contained definitions and includes required when hosting
+gdb on machine @var{xyz}. Those definitions and includes are now
+handled by Autoconf.
+
+New host and native configurations do not need this file.
+
+@emph{Maintainer's note: Some hosts continue to use the @file{xm-xyz.h}
+file to define the macros @var{HOST_FLOAT_FORMAT},
+@var{HOST_DOUBLE_FORMAT} and @var{HOST_LONG_DOUBLE_FORMAT}. That code
+also needs to be replaced with either an Autoconf or run-time test.}
@end table
@code{bfd_seek}). FIXME, should be replaced by SEEK_SET instead,
which is the POSIX equivalent.
-@item MALLOC_INCOMPATIBLE
-Define this if the system's prototype for @code{malloc} differs from the
-@sc{ansi} definition.
-
@item MMAP_BASE_ADDRESS
When using HAVE_MMAP, the first mapping should go at this address.
@samp{$} or @samp{$$}. For example, @code{$$dyncall} is a millicode
routine that handles inter-space procedure calls on PA-RISC.
-@item IEEE_FLOAT
-@findex IEEE_FLOAT
-Define this if the target system uses IEEE-format floating point numbers.
-
@item INIT_EXTRA_FRAME_INFO (@var{fromleaf}, @var{frame})
@findex INIT_EXTRA_FRAME_INFO
If additional information about the frame is required this should be
@code{BFD_ENDIAN_BIG} or @code{BFD_ENDIAN_LITTLE}. This macro replaces
@code{TARGET_BYTE_ORDER} which is deprecated.
-@item TARGET_BYTE_ORDER_SELECTABLE_P
-@findex TARGET_BYTE_ORDER_SELECTABLE_P
-Non-zero if the target has both @code{BIG_ENDIAN} and
-@code{BFD_ENDIAN_LITTLE} variants. This macro replaces
-@code{TARGET_BYTE_ORDER_SELECTABLE} which is deprecated.
-
@item TARGET_CHAR_BIT
@findex TARGET_CHAR_BIT
Number of bits in a char; defaults to 8.
@table @file
@vindex NATDEPFILES
@item gdb/config/@var{arch}/@var{xyz}.mh
-Specifies Makefile fragments needed when hosting @emph{or native} on
+Specifies Makefile fragments needed by a @emph{native} configuration on
machine @var{xyz}. In particular, this lists the required
native-dependent object files, by defining @samp{NATDEPFILES=@dots{}}.
Also specifies the header file which describes native support on
define @samp{NAT_CFLAGS}, @samp{NAT_ADD_FILES}, @samp{NAT_CLIBS},
@samp{NAT_CDEPS}, etc.; see @file{Makefile.in}.
+@emph{Maintainer's note: The @file{.mh} suffix is because this file
+originally contained @file{Makefile} fragments for hosting @value{GDBN}
+on machine @var{xyz}. While the file is no longer used for this
+purpose, the @file{.mh} suffix remains. Perhaphs someone will
+eventually rename these fragments so that they have a @file{.mn}
+suffix.}
+
@item gdb/config/@var{arch}/nm-@var{xyz}.h
(@file{nm.h} is a link to this file, created by @code{configure}). Contains C
macro definitions describing the native system environment, such as
setting @code{gdb_target} to something appropriate (for instance,
@var{xyz}).
+@emph{Maintainer's note: Work in progress. The file
+@file{gdb/configure.host} originally needed to be modified when either a
+new native target or a new host machine was being added to @value{GDBN}.
+Recent changes have removed this requirement. The file now only needs
+to be modified when adding a new native configuration. This will likely
+changed again in the future.}
+
@item
Finally, you'll need to specify and define @value{GDBN}'s host-, native-, and
target-dependent @file{.h} and @file{.c} files used for your
@printindex cp
-@c TeX can handle the contents at the start but makeinfo 3.12 can not
-@ifinfo
-@contents
-@end ifinfo
-@ifhtml
-@contents
-@end ifhtml
-
@bye
projects / deliverable / binutils-gdb.git / blobdiff