int stop_after_trap;
-/* Nonzero means expecting a trap and caller will handle it themselves.
- It is used after attach, due to attaching to a process;
- when running in the shell before the child program has been exec'd;
- and when running some kinds of remote stuff (FIXME?). */
-
-enum stop_kind stop_soon;
-
-/* Nonzero if proceed is being used for a "finish" command or a similar
- situation when stop_registers should be saved. */
-
-int proceed_to_finish;
-
/* Save register contents here when about to pop a stack dummy frame,
if-and-only-if proceed_to_finish is set.
Thus this contains the return value from the called function (assuming
static void
follow_exec (ptid_t pid, char *execd_pathname)
{
- ptid_t saved_pid = pid;
struct target_ops *tgt;
struct thread_info *th = inferior_thread ();
inferior has essentially been killed & reborn. */
gdb_flush (gdb_stdout);
- generic_mourn_inferior ();
- /* Because mourn_inferior resets inferior_ptid. */
- inferior_ptid = saved_pid;
+
+ breakpoint_init_inferior (inf_execd);
if (gdb_sysroot && *gdb_sysroot)
{
/* Saved contents of copy area. */
static gdb_byte *displaced_step_saved_copy;
-/* When this is non-zero, we are allowed to use displaced stepping, if
- the architecture supports it. When this is zero, we use
- traditional the hold-and-step approach. */
-int can_use_displaced_stepping = 1;
+/* Enum strings for "set|show displaced-stepping". */
+
+static const char can_use_displaced_stepping_auto[] = "auto";
+static const char can_use_displaced_stepping_on[] = "on";
+static const char can_use_displaced_stepping_off[] = "off";
+static const char *can_use_displaced_stepping_enum[] =
+{
+ can_use_displaced_stepping_auto,
+ can_use_displaced_stepping_on,
+ can_use_displaced_stepping_off,
+ NULL,
+};
+
+/* If ON, and the architecture supports it, GDB will use displaced
+ stepping to step over breakpoints. If OFF, or if the architecture
+ doesn't support it, GDB will instead use the traditional
+ hold-and-step approach. If AUTO (which is the default), GDB will
+ decide which technique to use to step over breakpoints depending on
+ which of all-stop or non-stop mode is active --- displaced stepping
+ in non-stop mode; hold-and-step in all-stop mode. */
+
+static const char *can_use_displaced_stepping =
+ can_use_displaced_stepping_auto;
+
static void
show_can_use_displaced_stepping (struct ui_file *file, int from_tty,
struct cmd_list_element *c,
const char *value)
{
- fprintf_filtered (file, _("\
-Debugger's willingness to use displaced stepping to step over "
-"breakpoints is %s.\n"), value);
+ if (can_use_displaced_stepping == can_use_displaced_stepping_auto)
+ fprintf_filtered (file, _("\
+Debugger's willingness to use displaced stepping to step over \
+breakpoints is %s (currently %s).\n"),
+ value, non_stop ? "on" : "off");
+ else
+ fprintf_filtered (file, _("\
+Debugger's willingness to use displaced stepping to step over \
+breakpoints is %s.\n"), value);
}
-/* Return non-zero if displaced stepping is enabled, and can be used
- with GDBARCH. */
+/* Return non-zero if displaced stepping can/should be used to step
+ over breakpoints. */
+
static int
use_displaced_stepping (struct gdbarch *gdbarch)
{
- return (can_use_displaced_stepping
+ return (((can_use_displaced_stepping == can_use_displaced_stepping_auto
+ && non_stop)
+ || can_use_displaced_stepping == can_use_displaced_stepping_on)
&& gdbarch_displaced_step_copy_insn_p (gdbarch));
}
static int
displaced_step_prepare (ptid_t ptid)
{
- struct cleanup *old_cleanups;
+ struct cleanup *old_cleanups, *ignore_cleanups;
struct regcache *regcache = get_thread_regcache (ptid);
struct gdbarch *gdbarch = get_regcache_arch (regcache);
CORE_ADDR original, copy;
displaced_step_clear ();
+ old_cleanups = save_inferior_ptid ();
+ inferior_ptid = ptid;
+
original = regcache_read_pc (regcache);
copy = gdbarch_displaced_step_location (gdbarch);
/* Save the original contents of the copy area. */
displaced_step_saved_copy = xmalloc (len);
- old_cleanups = make_cleanup (free_current_contents,
- &displaced_step_saved_copy);
+ ignore_cleanups = make_cleanup (free_current_contents,
+ &displaced_step_saved_copy);
read_memory (copy, displaced_step_saved_copy, len);
if (debug_displaced)
{
};
closure = gdbarch_displaced_step_copy_insn (gdbarch,
- original, copy, regcache);
+ original, copy, regcache);
/* We don't support the fully-simulated case at present. */
gdb_assert (closure);
/* Resume execution at the copy. */
regcache_write_pc (regcache, copy);
- discard_cleanups (old_cleanups);
+ discard_cleanups (ignore_cleanups);
+
+ do_cleanups (old_cleanups);
if (debug_displaced)
fprintf_unfiltered (gdb_stdlog, "displaced: displaced pc to 0x%s\n",
- paddr_nz (copy));
+ paddr_nz (copy));
/* Save the information we need to fix things up if the step
succeeds. */
do_cleanups (old_cleanups);
+ displaced_step_ptid = null_ptid;
+
/* Are there any pending displaced stepping requests? If so, run
one now. */
- if (displaced_step_request_queue)
+ while (displaced_step_request_queue)
{
struct displaced_step_request *head;
ptid_t ptid;
+ CORE_ADDR actual_pc;
head = displaced_step_request_queue;
ptid = head->ptid;
displaced_step_request_queue = head->next;
xfree (head);
- if (debug_displaced)
- fprintf_unfiltered (gdb_stdlog,
- "displaced: stepping queued %s now\n",
- target_pid_to_str (ptid));
+ context_switch (ptid);
+
+ actual_pc = read_pc ();
+ if (breakpoint_here_p (actual_pc))
+ {
+ if (debug_displaced)
+ fprintf_unfiltered (gdb_stdlog,
+ "displaced: stepping queued %s now\n",
+ target_pid_to_str (ptid));
- displaced_step_ptid = null_ptid;
- displaced_step_prepare (ptid);
- target_resume (ptid, 1, TARGET_SIGNAL_0);
+ displaced_step_prepare (ptid);
+
+ if (debug_displaced)
+ {
+ gdb_byte buf[4];
+
+ fprintf_unfiltered (gdb_stdlog, "displaced: run 0x%s: ",
+ paddr_nz (actual_pc));
+ read_memory (actual_pc, buf, sizeof (buf));
+ displaced_step_dump_bytes (gdb_stdlog, buf, sizeof (buf));
+ }
+
+ target_resume (ptid, 1, TARGET_SIGNAL_0);
+
+ /* Done, we're stepping a thread. */
+ break;
+ }
+ else
+ {
+ int step;
+ struct thread_info *tp = inferior_thread ();
+
+ /* The breakpoint we were sitting under has since been
+ removed. */
+ tp->trap_expected = 0;
+
+ /* Go back to what we were trying to do. */
+ step = currently_stepping (tp);
+
+ if (debug_displaced)
+ fprintf_unfiltered (gdb_stdlog, "breakpoint is gone %s: step(%d)\n",
+ target_pid_to_str (tp->ptid), step);
+
+ target_resume (ptid, step, TARGET_SIGNAL_0);
+ tp->stop_signal = TARGET_SIGNAL_0;
+
+ /* This request was discarded. See if there's any other
+ thread waiting for its turn. */
+ }
}
}
}
target_resume (resume_ptid, step, sig);
+
+ /* Avoid confusing the next resume, if the next stop/resume
+ happens to apply to another thread. */
+ tp->stop_signal = TARGET_SIGNAL_0;
}
discard_cleanups (old_cleanups);
{
if (!ptid_equal (inferior_ptid, null_ptid))
{
- struct thread_info *tp = inferior_thread ();
+ struct thread_info *tp;
+ struct inferior *inferior;
+
+ tp = inferior_thread ();
tp->trap_expected = 0;
tp->step_range_start = 0;
tp->step_range_end = 0;
tp->step_frame_id = null_frame_id;
+ tp->step_over_calls = STEP_OVER_UNDEBUGGABLE;
+ tp->stop_requested = 0;
+
+ tp->stop_step = 0;
+
+ tp->proceed_to_finish = 0;
+
+ /* Discard any remaining commands or status from previous
+ stop. */
+ bpstat_clear (&tp->stop_bpstat);
+
+ inferior = current_inferior ();
+ inferior->stop_soon = NO_STOP_QUIETLY;
}
- step_over_calls = STEP_OVER_UNDEBUGGABLE;
stop_after_trap = 0;
- stop_soon = NO_STOP_QUIETLY;
- proceed_to_finish = 0;
breakpoint_proceeded = 1; /* We're about to proceed... */
if (stop_registers)
regcache_xfree (stop_registers);
stop_registers = NULL;
}
-
- /* Discard any remaining commands or status from previous stop. */
- bpstat_clear (&stop_bpstat);
}
/* This should be suitable for any targets that support threads. */
struct thread_info *tp;
CORE_ADDR pc = regcache_read_pc (regcache);
int oneproc = 0;
+ enum target_signal stop_signal;
if (step > 0)
step_start_function = find_pc_function (pc);
if (addr == (CORE_ADDR) -1)
{
- if (pc == stop_pc && breakpoint_here_p (pc))
+ if (pc == stop_pc && breakpoint_here_p (pc)
+ && execution_direction != EXEC_REVERSE)
/* There is a breakpoint at the address we will resume at,
step one instruction before inserting breakpoints so that
we do not stop right away (and report a second hit at this
- breakpoint). */
+ breakpoint).
+
+ Note, we don't do this in reverse, because we won't
+ actually be executing the breakpoint insn anyway.
+ We'll be (un-)executing the previous instruction. */
+
oneproc = 1;
else if (gdbarch_single_step_through_delay_p (gdbarch)
&& gdbarch_single_step_through_delay (gdbarch,
if (! tp->trap_expected || use_displaced_stepping (gdbarch))
insert_breakpoints ();
+ if (!non_stop)
+ {
+ /* Pass the last stop signal to the thread we're resuming,
+ irrespective of whether the current thread is the thread that
+ got the last event or not. This was historically GDB's
+ behaviour before keeping a stop_signal per thread. */
+
+ struct thread_info *last_thread;
+ ptid_t last_ptid;
+ struct target_waitstatus last_status;
+
+ get_last_target_status (&last_ptid, &last_status);
+ if (!ptid_equal (inferior_ptid, last_ptid)
+ && !ptid_equal (last_ptid, null_ptid)
+ && !ptid_equal (last_ptid, minus_one_ptid))
+ {
+ last_thread = find_thread_pid (last_ptid);
+ if (last_thread)
+ {
+ tp->stop_signal = last_thread->stop_signal;
+ last_thread->stop_signal = TARGET_SIGNAL_0;
+ }
+ }
+ }
+
if (siggnal != TARGET_SIGNAL_DEFAULT)
- stop_signal = siggnal;
+ tp->stop_signal = siggnal;
/* If this signal should not be seen by program,
give it zero. Used for debugging signals. */
- else if (!signal_program[stop_signal])
- stop_signal = TARGET_SIGNAL_0;
+ else if (!signal_program[tp->stop_signal])
+ tp->stop_signal = TARGET_SIGNAL_0;
annotate_starting ();
init_infwait_state ();
/* Resume inferior. */
- resume (oneproc || step || bpstat_should_step (), stop_signal);
+ resume (oneproc || step || bpstat_should_step (), tp->stop_signal);
/* Wait for it to stop (if not standalone)
and in any case decode why it stopped, and act accordingly. */
void
start_remote (int from_tty)
{
+ struct inferior *inferior;
init_wait_for_inferior ();
- stop_soon = STOP_QUIETLY_REMOTE;
+
+ inferior = current_inferior ();
+ inferior->stop_soon = STOP_QUIETLY_REMOTE;
/* Always go on waiting for the target, regardless of the mode. */
/* FIXME: cagney/1999-09-23: At present it isn't possible to
breakpoint_init_inferior (inf_starting);
- /* Don't confuse first call to proceed(). */
- stop_signal = TARGET_SIGNAL_0;
-
/* The first resume is not following a fork/vfork/exec. */
pending_follow.kind = TARGET_WAITKIND_SPURIOUS; /* I.e., none. */
/* Inferior exited. */
EXITED,
/* Inferior received signal, and user asked to be notified. */
- SIGNAL_RECEIVED
+ SIGNAL_RECEIVED,
+ /* Reverse execution -- target ran out of history info. */
+ NO_HISTORY
};
/* The PTID we'll do a target_wait on.*/
void handle_inferior_event (struct execution_control_state *ecs);
-static void step_into_function (struct execution_control_state *ecs);
+static void handle_step_into_function (struct execution_control_state *ecs);
+static void handle_step_into_function_backward (struct execution_control_state *ecs);
static void insert_step_resume_breakpoint_at_frame (struct frame_info *step_frame);
static void insert_step_resume_breakpoint_at_caller (struct frame_info *);
static void insert_step_resume_breakpoint_at_sal (struct symtab_and_line sr_sal,
static void print_stop_reason (enum inferior_stop_reason stop_reason,
int stop_info);
+/* Callback for iterate over threads. If the thread is stopped, but
+ the user/frontend doesn't know about that yet, go through
+ normal_stop, as if the thread had just stopped now. ARG points at
+ a ptid. If PTID is MINUS_ONE_PTID, applies to all threads. If
+ ptid_is_pid(PTID) is true, applies to all threads of the process
+ pointed at by PTID. Otherwise, apply only to the thread pointed by
+ PTID. */
+
+static int
+infrun_thread_stop_requested_callback (struct thread_info *info, void *arg)
+{
+ ptid_t ptid = * (ptid_t *) arg;
+
+ if ((ptid_equal (info->ptid, ptid)
+ || ptid_equal (minus_one_ptid, ptid)
+ || (ptid_is_pid (ptid)
+ && ptid_get_pid (ptid) == ptid_get_pid (info->ptid)))
+ && is_running (info->ptid)
+ && !is_executing (info->ptid))
+ {
+ struct cleanup *old_chain;
+ struct execution_control_state ecss;
+ struct execution_control_state *ecs = &ecss;
+
+ memset (ecs, 0, sizeof (*ecs));
+
+ old_chain = make_cleanup_restore_current_thread ();
+
+ switch_to_thread (info->ptid);
+
+ /* Go through handle_inferior_event/normal_stop, so we always
+ have consistent output as if the stop event had been
+ reported. */
+ ecs->ptid = info->ptid;
+ ecs->event_thread = find_thread_pid (info->ptid);
+ ecs->ws.kind = TARGET_WAITKIND_STOPPED;
+ ecs->ws.value.sig = TARGET_SIGNAL_0;
+
+ handle_inferior_event (ecs);
+
+ if (!ecs->wait_some_more)
+ {
+ struct thread_info *tp;
+
+ normal_stop ();
+
+ /* Finish off the continuations. The continations
+ themselves are responsible for realising the thread
+ didn't finish what it was supposed to do. */
+ tp = inferior_thread ();
+ do_all_intermediate_continuations_thread (tp);
+ do_all_continuations_thread (tp);
+ }
+
+ do_cleanups (old_chain);
+ }
+
+ return 0;
+}
+
+/* This function is attached as a "thread_stop_requested" observer.
+ Cleanup local state that assumed the PTID was to be resumed, and
+ report the stop to the frontend. */
+
+void
+infrun_thread_stop_requested (ptid_t ptid)
+{
+ struct displaced_step_request *it, *next, *prev = NULL;
+
+ /* PTID was requested to stop. Remove it from the displaced
+ stepping queue, so we don't try to resume it automatically. */
+ for (it = displaced_step_request_queue; it; it = next)
+ {
+ next = it->next;
+
+ if (ptid_equal (it->ptid, ptid)
+ || ptid_equal (minus_one_ptid, ptid)
+ || (ptid_is_pid (ptid)
+ && ptid_get_pid (ptid) == ptid_get_pid (it->ptid)))
+ {
+ if (displaced_step_request_queue == it)
+ displaced_step_request_queue = it->next;
+ else
+ prev->next = it->next;
+
+ xfree (it);
+ }
+ else
+ prev = it;
+ }
+
+ iterate_over_threads (infrun_thread_stop_requested_callback, &ptid);
+}
+
/* Callback for iterate_over_threads. */
static int
else
ecs->ptid = target_wait (waiton_ptid, &ecs->ws);
- ecs->event_thread = find_thread_pid (ecs->ptid);
-
if (treat_exec_as_sigtrap && ecs->ws.kind == TARGET_WAITKIND_EXECD)
{
xfree (ecs->ws.value.execd_pathname);
thread. */
context_switch (ecs->ptid);
- ecs->event_thread = find_thread_pid (ecs->ptid);
-
/* Now figure out what to do with the result of the result. */
handle_inferior_event (ecs);
if (!ecs->wait_some_more)
{
+ struct inferior *inf = find_inferior_pid (ptid_get_pid (ecs->ptid));
+
delete_step_thread_step_resume_breakpoint ();
- if (stop_soon == NO_STOP_QUIETLY)
+ /* We may not find an inferior if this was a process exit. */
+ if (inf == NULL || inf->stop_soon == NO_STOP_QUIETLY)
normal_stop ();
- if (step_multi && stop_step)
+ if (target_has_execution
+ && ecs->ws.kind != TARGET_WAITKIND_EXITED
+ && ecs->ws.kind != TARGET_WAITKIND_SIGNALLED
+ && ecs->event_thread->step_multi
+ && ecs->event_thread->stop_step)
inferior_event_handler (INF_EXEC_CONTINUE, NULL);
else
inferior_event_handler (INF_EXEC_COMPLETE, NULL);
target_last_wait_ptid = minus_one_ptid;
}
-/* Switch thread contexts, maintaining "infrun state". */
+/* Switch thread contexts. */
static void
context_switch (ptid_t ptid)
{
- /* Caution: it may happen that the new thread (or the old one!)
- is not in the thread list. In this case we must not attempt
- to "switch context", or we run the risk that our context may
- be lost. This may happen as a result of the target module
- mishandling thread creation. */
-
if (debug_infrun)
{
fprintf_unfiltered (gdb_stdlog, "infrun: Switching context from %s ",
target_pid_to_str (ptid));
}
- if (in_thread_list (inferior_ptid) && in_thread_list (ptid))
- { /* Perform infrun state context switch: */
- /* Save infrun state for the old thread. */
- save_infrun_state (inferior_ptid,
- cmd_continuation, intermediate_continuation,
- proceed_to_finish,
- step_over_calls,
- stop_step,
- step_multi,
- stop_signal,
- stop_bpstat);
-
- /* Load infrun state for the new thread. */
- load_infrun_state (ptid,
- &cmd_continuation, &intermediate_continuation,
- &proceed_to_finish,
- &step_over_calls,
- &stop_step,
- &step_multi,
- &stop_signal,
- &stop_bpstat);
- }
-
switch_to_thread (ptid);
}
-/* Context switch to thread PTID. */
-ptid_t
-context_switch_to (ptid_t ptid)
-{
- ptid_t current_ptid = inferior_ptid;
-
- /* Context switch to the new thread. */
- if (!ptid_equal (ptid, inferior_ptid))
- {
- context_switch (ptid);
- }
- return current_ptid;
-}
-
static void
adjust_pc_after_break (struct execution_control_state *ecs)
{
if (ecs->ws.value.sig != TARGET_SIGNAL_TRAP)
return;
+ /* In reverse execution, when a breakpoint is hit, the instruction
+ under it has already been de-executed. The reported PC always
+ points at the breakpoint address, so adjusting it further would
+ be wrong. E.g., consider this case on a decr_pc_after_break == 1
+ architecture:
+
+ B1 0x08000000 : INSN1
+ B2 0x08000001 : INSN2
+ 0x08000002 : INSN3
+ PC -> 0x08000003 : INSN4
+
+ Say you're stopped at 0x08000003 as above. Reverse continuing
+ from that point should hit B2 as below. Reading the PC when the
+ SIGTRAP is reported should read 0x08000001 and INSN2 should have
+ been de-executed already.
+
+ B1 0x08000000 : INSN1
+ B2 PC -> 0x08000001 : INSN2
+ 0x08000002 : INSN3
+ 0x08000003 : INSN4
+
+ We can't apply the same logic as for forward execution, because
+ we would wrongly adjust the PC to 0x08000000, since there's a
+ breakpoint at PC - 1. We'd then report a hit on B1, although
+ INSN1 hadn't been de-executed yet. Doing nothing is the correct
+ behaviour. */
+ if (execution_direction == EXEC_REVERSE)
+ return;
+
/* If this target does not decrement the PC after breakpoints, then
we have nothing to do. */
regcache = get_thread_regcache (ecs->ptid);
breakpoint_pc = regcache_read_pc (regcache)
- gdbarch_decr_pc_after_break (gdbarch);
- /* Check whether there actually is a software breakpoint inserted
- at that location. */
- if (software_breakpoint_inserted_here_p (breakpoint_pc))
+ /* Check whether there actually is a software breakpoint inserted at
+ that location.
+
+ If in non-stop mode, a race condition is possible where we've
+ removed a breakpoint, but stop events for that breakpoint were
+ already queued and arrive later. To suppress those spurious
+ SIGTRAPs, we keep a list of such breakpoint locations for a bit,
+ and retire them after a number of stop events are reported. */
+ if (software_breakpoint_inserted_here_p (breakpoint_pc)
+ || (non_stop && moribund_breakpoint_here_p (breakpoint_pc)))
{
/* When using hardware single-step, a SIGTRAP is reported for both
a completed single-step and a software breakpoint. Need to
int stopped_by_watchpoint;
int stepped_after_stopped_by_watchpoint = 0;
struct symtab_and_line stop_pc_sal;
+ enum stop_kind stop_soon;
- breakpoint_retire_moribund ();
+ if (ecs->ws.kind != TARGET_WAITKIND_EXITED
+ && ecs->ws.kind != TARGET_WAITKIND_SIGNALLED
+ && ecs->ws.kind != TARGET_WAITKIND_IGNORE)
+ {
+ struct inferior *inf = find_inferior_pid (ptid_get_pid (ecs->ptid));
+ gdb_assert (inf);
+ stop_soon = inf->stop_soon;
+ }
+ else
+ stop_soon = NO_STOP_QUIETLY;
/* Cache the last pid/waitstatus. */
target_last_wait_ptid = ecs->ptid;
/* Always clear state belonging to the previous time we stopped. */
stop_stack_dummy = 0;
- adjust_pc_after_break (ecs);
-
- reinit_frame_cache ();
-
/* If it's a new process, add it to the thread database */
ecs->new_thread_event = (!ptid_equal (ecs->ptid, inferior_ptid)
&& ecs->ws.kind != TARGET_WAITKIND_SIGNALLED && ecs->new_thread_event)
add_thread (ecs->ptid);
+ ecs->event_thread = find_thread_pid (ecs->ptid);
+
+ /* Dependent on valid ECS->EVENT_THREAD. */
+ adjust_pc_after_break (ecs);
+
+ /* Dependent on the current PC value modified by adjust_pc_after_break. */
+ reinit_frame_cache ();
+
if (ecs->ws.kind != TARGET_WAITKIND_IGNORE)
{
+ breakpoint_retire_moribund ();
+
/* Mark the non-executing threads accordingly. */
if (!non_stop
|| ecs->ws.kind == TARGET_WAITKIND_EXITED
/* Record the exit code in the convenience variable $_exitcode, so
that the user can inspect this again later. */
set_internalvar (lookup_internalvar ("_exitcode"),
- value_from_longest (builtin_type_int,
+ value_from_longest (builtin_type_int32,
(LONGEST) ecs->ws.value.integer));
gdb_flush (gdb_stdout);
target_mourn_inferior ();
if (debug_infrun)
fprintf_unfiltered (gdb_stdlog, "infrun: TARGET_WAITKIND_SIGNALLED\n");
stop_print_frame = 0;
- stop_signal = ecs->ws.value.sig;
target_terminal_ours (); /* Must do this before mourn anyway */
/* Note: By definition of TARGET_WAITKIND_SIGNALLED, we shouldn't
may be needed. */
target_mourn_inferior ();
- print_stop_reason (SIGNAL_EXITED, stop_signal);
+ print_stop_reason (SIGNAL_EXITED, ecs->ws.value.sig);
singlestep_breakpoints_inserted_p = 0;
stop_stepping (ecs);
return;
case TARGET_WAITKIND_VFORKED:
if (debug_infrun)
fprintf_unfiltered (gdb_stdlog, "infrun: TARGET_WAITKIND_FORKED\n");
- stop_signal = TARGET_SIGNAL_TRAP;
pending_follow.kind = ecs->ws.kind;
pending_follow.fork_event.parent_pid = ecs->ptid;
stop_pc = read_pc ();
- stop_bpstat = bpstat_stop_status (stop_pc, ecs->ptid);
+ ecs->event_thread->stop_bpstat = bpstat_stop_status (stop_pc, ecs->ptid);
- ecs->random_signal = !bpstat_explains_signal (stop_bpstat);
+ ecs->random_signal = !bpstat_explains_signal (ecs->event_thread->stop_bpstat);
/* If no catchpoint triggered for this, then keep going. */
if (ecs->random_signal)
{
- stop_signal = TARGET_SIGNAL_0;
+ ecs->event_thread->stop_signal = TARGET_SIGNAL_0;
keep_going (ecs);
return;
}
+ ecs->event_thread->stop_signal = TARGET_SIGNAL_TRAP;
goto process_event_stop_test;
case TARGET_WAITKIND_EXECD:
if (debug_infrun)
fprintf_unfiltered (gdb_stdlog, "infrun: TARGET_WAITKIND_EXECD\n");
- stop_signal = TARGET_SIGNAL_TRAP;
-
pending_follow.execd_pathname =
savestring (ecs->ws.value.execd_pathname,
strlen (ecs->ws.value.execd_pathname));
- /* This causes the eventpoints and symbol table to be reset. Must
- do this now, before trying to determine whether to stop. */
- follow_exec (inferior_ptid, pending_follow.execd_pathname);
- xfree (pending_follow.execd_pathname);
-
- stop_pc = regcache_read_pc (get_thread_regcache (ecs->ptid));
-
- {
- /* The breakpoints module may need to touch the inferior's
- memory. Switch to the (stopped) event ptid
- momentarily. */
- ptid_t saved_inferior_ptid = inferior_ptid;
- inferior_ptid = ecs->ptid;
-
- stop_bpstat = bpstat_stop_status (stop_pc, ecs->ptid);
-
- ecs->random_signal = !bpstat_explains_signal (stop_bpstat);
- inferior_ptid = saved_inferior_ptid;
- }
-
if (!ptid_equal (ecs->ptid, inferior_ptid))
{
context_switch (ecs->ptid);
reinit_frame_cache ();
}
+ stop_pc = read_pc ();
+
+ /* This causes the eventpoints and symbol table to be reset.
+ Must do this now, before trying to determine whether to
+ stop. */
+ follow_exec (inferior_ptid, pending_follow.execd_pathname);
+ xfree (pending_follow.execd_pathname);
+
+ ecs->event_thread->stop_bpstat = bpstat_stop_status (stop_pc, ecs->ptid);
+ ecs->random_signal = !bpstat_explains_signal (ecs->event_thread->stop_bpstat);
+
/* If no catchpoint triggered for this, then keep going. */
if (ecs->random_signal)
{
- stop_signal = TARGET_SIGNAL_0;
+ ecs->event_thread->stop_signal = TARGET_SIGNAL_0;
keep_going (ecs);
return;
}
+ ecs->event_thread->stop_signal = TARGET_SIGNAL_TRAP;
goto process_event_stop_test;
/* Be careful not to try to gather much state about a thread
case TARGET_WAITKIND_STOPPED:
if (debug_infrun)
fprintf_unfiltered (gdb_stdlog, "infrun: TARGET_WAITKIND_STOPPED\n");
- stop_signal = ecs->ws.value.sig;
+ ecs->event_thread->stop_signal = ecs->ws.value.sig;
break;
+ case TARGET_WAITKIND_NO_HISTORY:
+ /* Reverse execution: target ran out of history info. */
+ stop_pc = read_pc ();
+ print_stop_reason (NO_HISTORY, 0);
+ stop_stepping (ecs);
+ return;
+
/* We had an event in the inferior, but we are not interested
in handling it at this level. The lower layers have already
done what needs to be done, if anything.
return;
}
- /* Do we need to clean up the state of a thread that has completed a
- displaced single-step? (Doing so usually affects the PC, so do
- it here, before we set stop_pc.) */
- displaced_step_fixup (ecs->ptid, stop_signal);
+ if (ecs->ws.kind == TARGET_WAITKIND_STOPPED)
+ {
+ /* Do we need to clean up the state of a thread that has
+ completed a displaced single-step? (Doing so usually affects
+ the PC, so do it here, before we set stop_pc.) */
+ displaced_step_fixup (ecs->ptid, ecs->event_thread->stop_signal);
+
+ /* If we either finished a single-step or hit a breakpoint, but
+ the user wanted this thread to be stopped, pretend we got a
+ SIG0 (generic unsignaled stop). */
+
+ if (ecs->event_thread->stop_requested
+ && ecs->event_thread->stop_signal == TARGET_SIGNAL_TRAP)
+ ecs->event_thread->stop_signal = TARGET_SIGNAL_0;
+ }
stop_pc = regcache_read_pc (get_thread_regcache (ecs->ptid));
/* We've either finished single-stepping past the single-step
breakpoint, or stopped for some other reason. It would be nice if
we could tell, but we can't reliably. */
- if (stop_signal == TARGET_SIGNAL_TRAP)
+ if (ecs->event_thread->stop_signal == TARGET_SIGNAL_TRAP)
{
if (debug_infrun)
fprintf_unfiltered (gdb_stdlog, "infrun: stepping_past_singlestep_breakpoint\n");
/* If we stopped for some other reason than single-stepping, ignore
the fact that we were supposed to switch back. */
- if (stop_signal == TARGET_SIGNAL_TRAP)
+ if (ecs->event_thread->stop_signal == TARGET_SIGNAL_TRAP)
{
struct thread_info *tp;
another thread. If so, then step that thread past the breakpoint,
and continue it. */
- if (stop_signal == TARGET_SIGNAL_TRAP)
+ if (ecs->event_thread->stop_signal == TARGET_SIGNAL_TRAP)
{
int thread_hop_needed = 0;
if (new_singlestep_pc != singlestep_pc)
{
+ enum target_signal stop_signal;
+
if (debug_infrun)
fprintf_unfiltered (gdb_stdlog, "infrun: unexpected thread,"
" but expected thread advanced also\n");
singlestep_ptid. Don't swap here, since that's
the context we want to use. Just fudge our
state and continue. */
+ stop_signal = ecs->event_thread->stop_signal;
+ ecs->event_thread->stop_signal = TARGET_SIGNAL_0;
ecs->ptid = singlestep_ptid;
ecs->event_thread = find_thread_pid (ecs->ptid);
+ ecs->event_thread->stop_signal = stop_signal;
stop_pc = new_singlestep_pc;
}
else
ecs->stop_func_start
+= gdbarch_deprecated_function_start_offset (current_gdbarch);
ecs->event_thread->stepping_over_breakpoint = 0;
- bpstat_clear (&stop_bpstat);
- stop_step = 0;
+ bpstat_clear (&ecs->event_thread->stop_bpstat);
+ ecs->event_thread->stop_step = 0;
stop_print_frame = 1;
ecs->random_signal = 0;
stopped_by_random_signal = 0;
- if (stop_signal == TARGET_SIGNAL_TRAP
+ if (ecs->event_thread->stop_signal == TARGET_SIGNAL_TRAP
&& ecs->event_thread->trap_expected
&& gdbarch_single_step_through_delay_p (current_gdbarch)
&& currently_stepping (ecs->event_thread))
If we're doing a displaced step past a breakpoint, then the
breakpoint is always inserted at the original instruction;
non-standard signals can't be explained by the breakpoint. */
- if (stop_signal == TARGET_SIGNAL_TRAP
+ if (ecs->event_thread->stop_signal == TARGET_SIGNAL_TRAP
|| (! ecs->event_thread->trap_expected
&& breakpoint_inserted_here_p (stop_pc)
- && (stop_signal == TARGET_SIGNAL_ILL
- || stop_signal == TARGET_SIGNAL_SEGV
- || stop_signal == TARGET_SIGNAL_EMT))
+ && (ecs->event_thread->stop_signal == TARGET_SIGNAL_ILL
+ || ecs->event_thread->stop_signal == TARGET_SIGNAL_SEGV
+ || ecs->event_thread->stop_signal == TARGET_SIGNAL_EMT))
|| stop_soon == STOP_QUIETLY || stop_soon == STOP_QUIETLY_NO_SIGSTOP
|| stop_soon == STOP_QUIETLY_REMOTE)
{
- if (stop_signal == TARGET_SIGNAL_TRAP && stop_after_trap)
+ if (ecs->event_thread->stop_signal == TARGET_SIGNAL_TRAP && stop_after_trap)
{
if (debug_infrun)
fprintf_unfiltered (gdb_stdlog, "infrun: stopped\n");
SIGTRAP. Some systems (e.g. Windows), and stubs supporting
target extended-remote report it instead of a SIGSTOP
(e.g. gdbserver). We already rely on SIGTRAP being our
- signal, so this is no exception. */
+ signal, so this is no exception.
+
+ Also consider that the attach is complete when we see a
+ TARGET_SIGNAL_0. In non-stop mode, GDB will explicitly tell
+ the target to stop all threads of the inferior, in case the
+ low level attach operation doesn't stop them implicitly. If
+ they weren't stopped implicitly, then the stub will report a
+ TARGET_SIGNAL_0, meaning: stopped for no particular reason
+ other than GDB's request. */
if (stop_soon == STOP_QUIETLY_NO_SIGSTOP
- && (stop_signal == TARGET_SIGNAL_STOP
- || stop_signal == TARGET_SIGNAL_TRAP))
+ && (ecs->event_thread->stop_signal == TARGET_SIGNAL_STOP
+ || ecs->event_thread->stop_signal == TARGET_SIGNAL_TRAP
+ || ecs->event_thread->stop_signal == TARGET_SIGNAL_0))
{
stop_stepping (ecs);
- stop_signal = TARGET_SIGNAL_0;
+ ecs->event_thread->stop_signal = TARGET_SIGNAL_0;
return;
}
/* See if there is a breakpoint at the current PC. */
- stop_bpstat = bpstat_stop_status (stop_pc, ecs->ptid);
+ ecs->event_thread->stop_bpstat = bpstat_stop_status (stop_pc, ecs->ptid);
/* Following in case break condition called a
function. */
another signal besides SIGTRAP, so check here as well as
above.''
- If someone ever tries to get get call dummys on a
+ If someone ever tries to get call dummys on a
non-executable stack to work (where the target would stop
with something like a SIGSEGV), then those tests might need
to be re-instated. Given, however, that the tests were only
be necessary for call dummies on a non-executable stack on
SPARC. */
- if (stop_signal == TARGET_SIGNAL_TRAP)
+ if (ecs->event_thread->stop_signal == TARGET_SIGNAL_TRAP)
ecs->random_signal
- = !(bpstat_explains_signal (stop_bpstat)
+ = !(bpstat_explains_signal (ecs->event_thread->stop_bpstat)
|| ecs->event_thread->trap_expected
|| (ecs->event_thread->step_range_end
&& ecs->event_thread->step_resume_breakpoint == NULL));
else
{
- ecs->random_signal = !bpstat_explains_signal (stop_bpstat);
+ ecs->random_signal = !bpstat_explains_signal (ecs->event_thread->stop_bpstat);
if (!ecs->random_signal)
- stop_signal = TARGET_SIGNAL_TRAP;
+ ecs->event_thread->stop_signal = TARGET_SIGNAL_TRAP;
}
}
int printed = 0;
if (debug_infrun)
- fprintf_unfiltered (gdb_stdlog, "infrun: random signal %d\n", stop_signal);
+ fprintf_unfiltered (gdb_stdlog, "infrun: random signal %d\n",
+ ecs->event_thread->stop_signal);
stopped_by_random_signal = 1;
- if (signal_print[stop_signal])
+ if (signal_print[ecs->event_thread->stop_signal])
{
printed = 1;
target_terminal_ours_for_output ();
- print_stop_reason (SIGNAL_RECEIVED, stop_signal);
+ print_stop_reason (SIGNAL_RECEIVED, ecs->event_thread->stop_signal);
}
- if (signal_stop_state (stop_signal))
+ /* Always stop on signals if we're either just gaining control
+ of the program, or the user explicitly requested this thread
+ to remain stopped. */
+ if (stop_soon != NO_STOP_QUIETLY
+ || ecs->event_thread->stop_requested
+ || signal_stop_state (ecs->event_thread->stop_signal))
{
stop_stepping (ecs);
return;
target_terminal_inferior ();
/* Clear the signal if it should not be passed. */
- if (signal_program[stop_signal] == 0)
- stop_signal = TARGET_SIGNAL_0;
+ if (signal_program[ecs->event_thread->stop_signal] == 0)
+ ecs->event_thread->stop_signal = TARGET_SIGNAL_0;
if (ecs->event_thread->prev_pc == read_pc ()
&& ecs->event_thread->trap_expected
}
if (ecs->event_thread->step_range_end != 0
- && stop_signal != TARGET_SIGNAL_0
+ && ecs->event_thread->stop_signal != TARGET_SIGNAL_0
&& (ecs->event_thread->step_range_start <= stop_pc
&& stop_pc < ecs->event_thread->step_range_end)
&& frame_id_eq (get_frame_id (get_current_frame ()),
CORE_ADDR jmp_buf_pc;
struct bpstat_what what;
- what = bpstat_what (stop_bpstat);
+ what = bpstat_what (ecs->event_thread->stop_bpstat);
if (what.call_dummy)
{
gdb_assert (ecs->event_thread->step_resume_breakpoint != NULL);
delete_step_resume_breakpoint (ecs->event_thread);
- stop_step = 1;
+ ecs->event_thread->stop_step = 1;
print_stop_reason (END_STEPPING_RANGE, 0);
stop_stepping (ecs);
return;
keep_going (ecs);
return;
}
+ if (stop_pc == ecs->stop_func_start
+ && execution_direction == EXEC_REVERSE)
+ {
+ /* We are stepping over a function call in reverse, and
+ just hit the step-resume breakpoint at the start
+ address of the function. Go back to single-stepping,
+ which should take us back to the function call. */
+ ecs->event_thread->stepping_over_breakpoint = 1;
+ keep_going (ecs);
+ return;
+ }
break;
case BPSTAT_WHAT_CHECK_SHLIBS:
code or stubs in libdld.sl, such as "shl_load" and
friends) until we reach non-dld code. At that point,
we can stop stepping. */
- bpstat_get_triggered_catchpoints (stop_bpstat,
+ bpstat_get_triggered_catchpoints (ecs->event_thread->stop_bpstat,
&ecs->
event_thread->
stepping_through_solib_catchpoints);
/* Else, stop and report the catchpoint(s) whose triggering
caused us to begin stepping. */
ecs->event_thread->stepping_through_solib_after_catch = 0;
- bpstat_clear (&stop_bpstat);
- stop_bpstat = bpstat_copy (ecs->event_thread->stepping_through_solib_catchpoints);
+ bpstat_clear (&ecs->event_thread->stop_bpstat);
+ ecs->event_thread->stop_bpstat
+ = bpstat_copy (ecs->event_thread->stepping_through_solib_catchpoints);
bpstat_clear (&ecs->event_thread->stepping_through_solib_catchpoints);
stop_print_frame = 1;
stop_stepping (ecs);
&& stop_pc < ecs->event_thread->step_range_end)
{
if (debug_infrun)
- fprintf_unfiltered (gdb_stdlog, "infrun: stepping inside range [0x%s-0x%s]\n",
+ fprintf_unfiltered (gdb_stdlog, "infrun: stepping inside range [0x%s-0x%s]\n",
paddr_nz (ecs->event_thread->step_range_start),
paddr_nz (ecs->event_thread->step_range_end));
- keep_going (ecs);
+
+ /* When stepping backward, stop at beginning of line range
+ (unless it's the function entry point, in which case
+ keep going back to the call point). */
+ if (stop_pc == ecs->event_thread->step_range_start
+ && stop_pc != ecs->stop_func_start
+ && execution_direction == EXEC_REVERSE)
+ {
+ ecs->event_thread->stop_step = 1;
+ print_stop_reason (END_STEPPING_RANGE, 0);
+ stop_stepping (ecs);
+ }
+ else
+ keep_going (ecs);
+
return;
}
loader dynamic symbol resolution code, we keep on single stepping
until we exit the run time loader code and reach the callee's
address. */
- if (step_over_calls == STEP_OVER_UNDEBUGGABLE
+ if (ecs->event_thread->step_over_calls == STEP_OVER_UNDEBUGGABLE
&& in_solib_dynsym_resolve_code (stop_pc))
{
CORE_ADDR pc_after_resolver =
}
if (ecs->event_thread->step_range_end != 1
- && (step_over_calls == STEP_OVER_UNDEBUGGABLE
- || step_over_calls == STEP_OVER_ALL)
+ && (ecs->event_thread->step_over_calls == STEP_OVER_UNDEBUGGABLE
+ || ecs->event_thread->step_over_calls == STEP_OVER_ALL)
&& get_frame_type (get_current_frame ()) == SIGTRAMP_FRAME)
{
if (debug_infrun)
previous frame must have valid frame IDs. */
if (!frame_id_eq (get_frame_id (get_current_frame ()),
ecs->event_thread->step_frame_id)
- && frame_id_eq (frame_unwind_id (get_current_frame ()),
- ecs->event_thread->step_frame_id))
+ && (frame_id_eq (frame_unwind_id (get_current_frame ()),
+ ecs->event_thread->step_frame_id)
+ || execution_direction == EXEC_REVERSE))
{
CORE_ADDR real_stop_pc;
if (debug_infrun)
fprintf_unfiltered (gdb_stdlog, "infrun: stepped into subroutine\n");
- if ((step_over_calls == STEP_OVER_NONE)
+ if ((ecs->event_thread->step_over_calls == STEP_OVER_NONE)
|| ((ecs->event_thread->step_range_end == 1)
&& in_prologue (ecs->event_thread->prev_pc,
ecs->stop_func_start)))
/* Also, maybe we just did a "nexti" inside a prolog, so we
thought it was a subroutine call but it was not. Stop as
well. FENN */
- stop_step = 1;
+ ecs->event_thread->stop_step = 1;
print_stop_reason (END_STEPPING_RANGE, 0);
stop_stepping (ecs);
return;
}
- if (step_over_calls == STEP_OVER_ALL)
+ if (ecs->event_thread->step_over_calls == STEP_OVER_ALL)
{
- /* We're doing a "next", set a breakpoint at callee's return
- address (the address at which the caller will
- resume). */
- insert_step_resume_breakpoint_at_caller (get_current_frame ());
+ /* We're doing a "next".
+
+ Normal (forward) execution: set a breakpoint at the
+ callee's return address (the address at which the caller
+ will resume).
+
+ Reverse (backward) execution. set the step-resume
+ breakpoint at the start of the function that we just
+ stepped into (backwards), and continue to there. When we
+ get there, we'll need to single-step back to the caller. */
+
+ if (execution_direction == EXEC_REVERSE)
+ {
+ struct symtab_and_line sr_sal;
+
+ if (ecs->stop_func_start == 0
+ && in_solib_dynsym_resolve_code (stop_pc))
+ {
+ /* Stepped into runtime loader dynamic symbol
+ resolution code. Since we're in reverse,
+ we have already backed up through the runtime
+ loader and the dynamic function. This is just
+ the trampoline (jump table).
+
+ Just keep stepping, we'll soon be home.
+ */
+ keep_going (ecs);
+ return;
+ }
+ /* Normal (staticly linked) function call return. */
+ init_sal (&sr_sal);
+ sr_sal.pc = ecs->stop_func_start;
+ insert_step_resume_breakpoint_at_sal (sr_sal, null_frame_id);
+ }
+ else
+ insert_step_resume_breakpoint_at_caller (get_current_frame ());
+
keep_going (ecs);
return;
}
if (real_stop_pc != 0)
ecs->stop_func_start = real_stop_pc;
- if (in_solib_dynsym_resolve_code (ecs->stop_func_start))
+ if (real_stop_pc != 0 && in_solib_dynsym_resolve_code (real_stop_pc))
{
struct symtab_and_line sr_sal;
init_sal (&sr_sal);
tmp_sal = find_pc_line (ecs->stop_func_start, 0);
if (tmp_sal.line != 0)
{
- step_into_function (ecs);
+ if (execution_direction == EXEC_REVERSE)
+ handle_step_into_function_backward (ecs);
+ else
+ handle_step_into_function (ecs);
return;
}
}
/* If we have no line number and the step-stop-if-no-debug is
set, we stop the step so that the user has a chance to switch
in assembly mode. */
- if (step_over_calls == STEP_OVER_UNDEBUGGABLE && step_stop_if_no_debug)
+ if (ecs->event_thread->step_over_calls == STEP_OVER_UNDEBUGGABLE
+ && step_stop_if_no_debug)
{
- stop_step = 1;
+ ecs->event_thread->stop_step = 1;
print_stop_reason (END_STEPPING_RANGE, 0);
stop_stepping (ecs);
return;
}
- /* Set a breakpoint at callee's return address (the address at
- which the caller will resume). */
- insert_step_resume_breakpoint_at_caller (get_current_frame ());
+ if (execution_direction == EXEC_REVERSE)
+ {
+ /* Set a breakpoint at callee's start address.
+ From there we can step once and be back in the caller. */
+ struct symtab_and_line sr_sal;
+ init_sal (&sr_sal);
+ sr_sal.pc = ecs->stop_func_start;
+ insert_step_resume_breakpoint_at_sal (sr_sal, null_frame_id);
+ }
+ else
+ /* Set a breakpoint at callee's return address (the address
+ at which the caller will resume). */
+ insert_step_resume_breakpoint_at_caller (get_current_frame ());
+
keep_going (ecs);
return;
}
/* NOTE: tausq/2004-05-24: This if block used to be done before all
the trampoline processing logic, however, there are some trampolines
that have no names, so we should do trampoline handling first. */
- if (step_over_calls == STEP_OVER_UNDEBUGGABLE
+ if (ecs->event_thread->step_over_calls == STEP_OVER_UNDEBUGGABLE
&& ecs->stop_func_name == NULL
&& stop_pc_sal.line == 0)
{
/* If we have no line number and the step-stop-if-no-debug
is set, we stop the step so that the user has a chance to
switch in assembly mode. */
- stop_step = 1;
+ ecs->event_thread->stop_step = 1;
print_stop_reason (END_STEPPING_RANGE, 0);
stop_stepping (ecs);
return;
one instruction. */
if (debug_infrun)
fprintf_unfiltered (gdb_stdlog, "infrun: stepi/nexti\n");
- stop_step = 1;
+ ecs->event_thread->stop_step = 1;
print_stop_reason (END_STEPPING_RANGE, 0);
stop_stepping (ecs);
return;
or can this happen as a result of a return or longjmp?). */
if (debug_infrun)
fprintf_unfiltered (gdb_stdlog, "infrun: no line number info\n");
- stop_step = 1;
+ ecs->event_thread->stop_step = 1;
print_stop_reason (END_STEPPING_RANGE, 0);
stop_stepping (ecs);
return;
better. */
if (debug_infrun)
fprintf_unfiltered (gdb_stdlog, "infrun: stepped to a different line\n");
- stop_step = 1;
+ ecs->event_thread->stop_step = 1;
print_stop_reason (END_STEPPING_RANGE, 0);
stop_stepping (ecs);
return;
|| bpstat_should_step ());
}
-/* Subroutine call with source code we should not step over. Do step
- to the first line of code in it. */
+/* Inferior has stepped into a subroutine call with source code that
+ we should not step over. Do step to the first line of code in
+ it. */
static void
-step_into_function (struct execution_control_state *ecs)
+handle_step_into_function (struct execution_control_state *ecs)
{
struct symtab *s;
struct symtab_and_line stop_func_sal, sr_sal;
s = find_pc_symtab (stop_pc);
if (s && s->language != language_asm)
- ecs->stop_func_start = gdbarch_skip_prologue
- (current_gdbarch, ecs->stop_func_start);
+ ecs->stop_func_start = gdbarch_skip_prologue (current_gdbarch,
+ ecs->stop_func_start);
stop_func_sal = find_pc_line (ecs->stop_func_start, 0);
/* Use the step_resume_break to step until the end of the prologue,
if (ecs->stop_func_start == stop_pc)
{
/* We are already there: stop now. */
- stop_step = 1;
+ ecs->event_thread->stop_step = 1;
print_stop_reason (END_STEPPING_RANGE, 0);
stop_stepping (ecs);
return;
keep_going (ecs);
}
+/* Inferior has stepped backward into a subroutine call with source
+ code that we should not step over. Do step to the beginning of the
+ last line of code in it. */
+
+static void
+handle_step_into_function_backward (struct execution_control_state *ecs)
+{
+ struct symtab *s;
+ struct symtab_and_line stop_func_sal, sr_sal;
+
+ s = find_pc_symtab (stop_pc);
+ if (s && s->language != language_asm)
+ ecs->stop_func_start = gdbarch_skip_prologue (current_gdbarch,
+ ecs->stop_func_start);
+
+ stop_func_sal = find_pc_line (stop_pc, 0);
+
+ /* OK, we're just going to keep stepping here. */
+ if (stop_func_sal.pc == stop_pc)
+ {
+ /* We're there already. Just stop stepping now. */
+ ecs->event_thread->stop_step = 1;
+ print_stop_reason (END_STEPPING_RANGE, 0);
+ stop_stepping (ecs);
+ }
+ else
+ {
+ /* Else just reset the step range and keep going.
+ No step-resume breakpoint, they don't work for
+ epilogues, which can have multiple entry paths. */
+ ecs->event_thread->step_range_start = stop_func_sal.pc;
+ ecs->event_thread->step_range_end = stop_func_sal.end;
+ keep_going (ecs);
+ }
+ return;
+}
+
/* Insert a "step-resume breakpoint" at SR_SAL with frame ID SR_ID.
This is used to both functions and to skip over code. */
/* If we did not do break;, it means we should keep running the
inferior and not return to debugger. */
- if (ecs->event_thread->trap_expected && stop_signal != TARGET_SIGNAL_TRAP)
+ if (ecs->event_thread->trap_expected
+ && ecs->event_thread->stop_signal != TARGET_SIGNAL_TRAP)
{
/* We took a signal (which we are supposed to pass through to
the inferior, else we'd not get here) and we haven't yet
gotten our trap. Simply continue. */
- resume (currently_stepping (ecs->event_thread), stop_signal);
+ resume (currently_stepping (ecs->event_thread),
+ ecs->event_thread->stop_signal);
}
else
{
simulator; the simulator then delivers the hardware
equivalent of a SIGNAL_TRAP to the program being debugged. */
- if (stop_signal == TARGET_SIGNAL_TRAP && !signal_program[stop_signal])
- stop_signal = TARGET_SIGNAL_0;
-
+ if (ecs->event_thread->stop_signal == TARGET_SIGNAL_TRAP
+ && !signal_program[ecs->event_thread->stop_signal])
+ ecs->event_thread->stop_signal = TARGET_SIGNAL_0;
- resume (currently_stepping (ecs->event_thread), stop_signal);
+ resume (currently_stepping (ecs->event_thread),
+ ecs->event_thread->stop_signal);
}
prepare_to_wait (ecs);
/* For now print nothing. */
/* Print a message only if not in the middle of doing a "step n"
operation for n > 1 */
- if (!step_multi || !stop_step)
+ if (!inferior_thread ()->step_multi
+ || !inferior_thread ()->stop_step)
if (ui_out_is_mi_like_p (uiout))
ui_out_field_string
(uiout, "reason",
return_child_result_value = stop_info;
break;
case SIGNAL_RECEIVED:
- /* Signal received. The signal table tells us to print about
- it. */
+ /* Signal received. The signal table tells us to print about
+ it. */
annotate_signal ();
- ui_out_text (uiout, "\nProgram received signal ");
- annotate_signal_name ();
- if (ui_out_is_mi_like_p (uiout))
- ui_out_field_string
- (uiout, "reason", async_reason_lookup (EXEC_ASYNC_SIGNAL_RECEIVED));
- ui_out_field_string (uiout, "signal-name",
- target_signal_to_name (stop_info));
- annotate_signal_name_end ();
- ui_out_text (uiout, ", ");
- annotate_signal_string ();
- ui_out_field_string (uiout, "signal-meaning",
- target_signal_to_string (stop_info));
- annotate_signal_string_end ();
+
+ if (stop_info == TARGET_SIGNAL_0 && !ui_out_is_mi_like_p (uiout))
+ {
+ struct thread_info *t = inferior_thread ();
+
+ ui_out_text (uiout, "\n[");
+ ui_out_field_string (uiout, "thread-name",
+ target_pid_to_str (t->ptid));
+ ui_out_field_fmt (uiout, "thread-id", "] #%d", t->num);
+ ui_out_text (uiout, " stopped");
+ }
+ else
+ {
+ ui_out_text (uiout, "\nProgram received signal ");
+ annotate_signal_name ();
+ if (ui_out_is_mi_like_p (uiout))
+ ui_out_field_string
+ (uiout, "reason", async_reason_lookup (EXEC_ASYNC_SIGNAL_RECEIVED));
+ ui_out_field_string (uiout, "signal-name",
+ target_signal_to_name (stop_info));
+ annotate_signal_name_end ();
+ ui_out_text (uiout, ", ");
+ annotate_signal_string ();
+ ui_out_field_string (uiout, "signal-meaning",
+ target_signal_to_string (stop_info));
+ annotate_signal_string_end ();
+ }
ui_out_text (uiout, ".\n");
break;
+ case NO_HISTORY:
+ /* Reverse execution: target ran out of history info. */
+ ui_out_text (uiout, "\nNo more reverse-execution history.\n");
+ break;
default:
internal_error (__FILE__, __LINE__,
_("print_stop_reason: unrecognized enum value"));
/* Don't print a message if in the middle of doing a "step n"
operation for n > 1 */
- if (step_multi && stop_step)
+ if (target_has_execution
+ && last.kind != TARGET_WAITKIND_SIGNALLED
+ && last.kind != TARGET_WAITKIND_EXITED
+ && inferior_thread ()->step_multi
+ && inferior_thread ()->stop_step)
goto done;
target_terminal_ours ();
if (target_has_stack && !stop_stack_dummy)
set_current_sal_from_frame (get_current_frame (), 1);
- /* Look up the hook_stop and run it (CLI internally handles problem
- of stop_command's pre-hook not existing). */
- if (stop_command)
- catch_errors (hook_stop_stub, stop_command,
- "Error while running hook_stop:\n", RETURN_MASK_ALL);
-
if (!target_has_stack)
- {
+ goto done;
- goto done;
- }
+ if (last.kind == TARGET_WAITKIND_SIGNALLED
+ || last.kind == TARGET_WAITKIND_EXITED)
+ goto done;
/* Select innermost stack frame - i.e., current frame is frame 0,
and current location is based on that.
int bpstat_ret;
int source_flag;
int do_frame_printing = 1;
+ struct thread_info *tp = inferior_thread ();
- bpstat_ret = bpstat_print (stop_bpstat);
+ bpstat_ret = bpstat_print (tp->stop_bpstat);
switch (bpstat_ret)
{
case PRINT_UNKNOWN:
/* FIXME: cagney/2002-12-01: Given that a frame ID does
(or should) carry around the function and does (or
should) use that when doing a frame comparison. */
- if (stop_step
- && frame_id_eq (inferior_thread ()->step_frame_id,
+ if (tp->stop_step
+ && frame_id_eq (tp->step_frame_id,
get_frame_id (get_current_frame ()))
&& step_start_function == find_pc_function (stop_pc))
source_flag = SRC_LINE; /* finished step, just print source line */
/* Save the function value return registers, if we care.
We might be about to restore their previous contents. */
- if (proceed_to_finish)
+ if (inferior_thread ()->proceed_to_finish)
{
/* This should not be necessary. */
if (stop_registers)
done:
annotate_stopped ();
- if (!suppress_stop_observer && !step_multi)
- observer_notify_normal_stop (stop_bpstat);
- /* Delete the breakpoint we stopped at, if it wants to be deleted.
- Delete any breakpoint that is to be deleted at the next stop. */
- breakpoint_auto_delete (stop_bpstat);
-
+ if (!suppress_stop_observer
+ && !(target_has_execution
+ && last.kind != TARGET_WAITKIND_SIGNALLED
+ && last.kind != TARGET_WAITKIND_EXITED
+ && inferior_thread ()->step_multi))
+ {
+ if (!ptid_equal (inferior_ptid, null_ptid))
+ observer_notify_normal_stop (inferior_thread ()->stop_bpstat);
+ else
+ observer_notify_normal_stop (NULL);
+ }
if (target_has_execution
&& last.kind != TARGET_WAITKIND_SIGNALLED
&& last.kind != TARGET_WAITKIND_EXITED)
{
+ /* Delete the breakpoint we stopped at, if it wants to be deleted.
+ Delete any breakpoint that is to be deleted at the next stop. */
+ breakpoint_auto_delete (inferior_thread ()->stop_bpstat);
+
if (!non_stop)
set_running (pid_to_ptid (-1), 0);
else
set_running (inferior_ptid, 0);
}
+
+ /* Look up the hook_stop and run it (CLI internally handles problem
+ of stop_command's pre-hook not existing). */
+ if (stop_command)
+ catch_errors (hook_stop_stub, stop_command,
+ "Error while running hook_stop:\n", RETURN_MASK_ALL);
+
}
static int
int
signal_stop_state (int signo)
{
- /* Always stop on signals if we're just gaining control of the
- program. */
- return signal_stop[signo] || stop_soon != NO_STOP_QUIETLY;
+ return signal_stop[signo];
}
int
/* Break the command line up into args. */
- argv = buildargv (args);
- if (argv == NULL)
- {
- nomem (0);
- }
+ argv = gdb_buildargv (args);
old_chain = make_cleanup_freeargv (argv);
/* Walk through the args, looking for signal oursigs, signal names, and
char **argv;
struct cleanup *old_chain;
+ if (args == NULL)
+ error_no_arg (_("xdb command"));
+
/* Break the command line up into args. */
- argv = buildargv (args);
- if (argv == NULL)
- {
- nomem (0);
- }
+ argv = gdb_buildargv (args);
old_chain = make_cleanup_freeargv (argv);
if (argv[1] != (char *) NULL)
{
int proceed_to_finish;
};
-void
-write_inferior_status_register (struct inferior_status *inf_status, int regno,
- LONGEST val)
-{
- int size = register_size (current_gdbarch, regno);
- void *buf = alloca (size);
- store_signed_integer (buf, size, val);
- regcache_raw_write (inf_status->registers, regno, buf);
-}
-
/* Save all of the information associated with the inferior<==>gdb
connection. INF_STATUS is a pointer to a "struct inferior_status"
(defined in inferior.h). */
{
struct inferior_status *inf_status = XMALLOC (struct inferior_status);
struct thread_info *tp = inferior_thread ();
+ struct inferior *inf = current_inferior ();
- inf_status->stop_signal = stop_signal;
+ inf_status->stop_signal = tp->stop_signal;
inf_status->stop_pc = stop_pc;
- inf_status->stop_step = stop_step;
+ inf_status->stop_step = tp->stop_step;
inf_status->stop_stack_dummy = stop_stack_dummy;
inf_status->stopped_by_random_signal = stopped_by_random_signal;
inf_status->stepping_over_breakpoint = tp->trap_expected;
inf_status->step_range_start = tp->step_range_start;
inf_status->step_range_end = tp->step_range_end;
inf_status->step_frame_id = tp->step_frame_id;
- inf_status->step_over_calls = step_over_calls;
+ inf_status->step_over_calls = tp->step_over_calls;
inf_status->stop_after_trap = stop_after_trap;
- inf_status->stop_soon = stop_soon;
+ inf_status->stop_soon = inf->stop_soon;
/* Save original bpstat chain here; replace it with copy of chain.
If caller's caller is walking the chain, they'll be happier if we
hand them back the original chain when restore_inferior_status is
called. */
- inf_status->stop_bpstat = stop_bpstat;
- stop_bpstat = bpstat_copy (stop_bpstat);
+ inf_status->stop_bpstat = tp->stop_bpstat;
+ tp->stop_bpstat = bpstat_copy (tp->stop_bpstat);
inf_status->breakpoint_proceeded = breakpoint_proceeded;
inf_status->restore_stack_info = restore_stack_info;
- inf_status->proceed_to_finish = proceed_to_finish;
+ inf_status->proceed_to_finish = tp->proceed_to_finish;
inf_status->registers = regcache_dup (get_current_regcache ());
restore_inferior_status (struct inferior_status *inf_status)
{
struct thread_info *tp = inferior_thread ();
+ struct inferior *inf = current_inferior ();
- stop_signal = inf_status->stop_signal;
+ tp->stop_signal = inf_status->stop_signal;
stop_pc = inf_status->stop_pc;
- stop_step = inf_status->stop_step;
+ tp->stop_step = inf_status->stop_step;
stop_stack_dummy = inf_status->stop_stack_dummy;
stopped_by_random_signal = inf_status->stopped_by_random_signal;
tp->trap_expected = inf_status->stepping_over_breakpoint;
tp->step_range_start = inf_status->step_range_start;
tp->step_range_end = inf_status->step_range_end;
tp->step_frame_id = inf_status->step_frame_id;
- step_over_calls = inf_status->step_over_calls;
+ tp->step_over_calls = inf_status->step_over_calls;
stop_after_trap = inf_status->stop_after_trap;
- stop_soon = inf_status->stop_soon;
- bpstat_clear (&stop_bpstat);
- stop_bpstat = inf_status->stop_bpstat;
+ inf->stop_soon = inf_status->stop_soon;
+ bpstat_clear (&tp->stop_bpstat);
+ tp->stop_bpstat = inf_status->stop_bpstat;
breakpoint_proceeded = inf_status->breakpoint_proceeded;
- proceed_to_finish = inf_status->proceed_to_finish;
+ tp->proceed_to_finish = inf_status->proceed_to_finish;
/* The inferior can be gone if the user types "print exit(0)"
(and perhaps other times). */
&& ptid1.tid == ptid2.tid);
}
+/* Returns true if PTID represents a process. */
+
+int
+ptid_is_pid (ptid_t ptid)
+{
+ if (ptid_equal (minus_one_ptid, ptid))
+ return 0;
+ if (ptid_equal (null_ptid, ptid))
+ return 0;
+
+ return (ptid_get_lwp (ptid) == 0 && ptid_get_tid (ptid) == 0);
+}
+
/* restore_inferior_ptid() will be used by the cleanup machinery
to restore the inferior_ptid value saved in a call to
save_inferior_ptid(). */
}
\f
+/* User interface for reverse debugging:
+ Set exec-direction / show exec-direction commands
+ (returns error unless target implements to_set_exec_direction method). */
+
+enum exec_direction_kind execution_direction = EXEC_FORWARD;
+static const char exec_forward[] = "forward";
+static const char exec_reverse[] = "reverse";
+static const char *exec_direction = exec_forward;
+static const char *exec_direction_names[] = {
+ exec_forward,
+ exec_reverse,
+ NULL
+};
+
+static void
+set_exec_direction_func (char *args, int from_tty,
+ struct cmd_list_element *cmd)
+{
+ if (target_can_execute_reverse)
+ {
+ if (!strcmp (exec_direction, exec_forward))
+ execution_direction = EXEC_FORWARD;
+ else if (!strcmp (exec_direction, exec_reverse))
+ execution_direction = EXEC_REVERSE;
+ }
+}
+
+static void
+show_exec_direction_func (struct ui_file *out, int from_tty,
+ struct cmd_list_element *cmd, const char *value)
+{
+ switch (execution_direction) {
+ case EXEC_FORWARD:
+ fprintf_filtered (out, _("Forward.\n"));
+ break;
+ case EXEC_REVERSE:
+ fprintf_filtered (out, _("Reverse.\n"));
+ break;
+ case EXEC_ERROR:
+ default:
+ fprintf_filtered (out,
+ _("Forward (target `%s' does not support exec-direction).\n"),
+ target_shortname);
+ break;
+ }
+}
+
+/* User interface for non-stop mode. */
+
int non_stop = 0;
static int non_stop_1 = 0;
show_step_stop_if_no_debug,
&setlist, &showlist);
- add_setshow_boolean_cmd ("can-use-displaced-stepping", class_maintenance,
- &can_use_displaced_stepping, _("\
+ add_setshow_enum_cmd ("displaced-stepping", class_run,
+ can_use_displaced_stepping_enum,
+ &can_use_displaced_stepping, _("\
Set debugger's willingness to use displaced stepping."), _("\
Show debugger's willingness to use displaced stepping."), _("\
-If zero, gdb will not use displaced stepping to step over\n\
-breakpoints, even if such is supported by the target."),
- NULL,
- show_can_use_displaced_stepping,
- &maintenance_set_cmdlist,
- &maintenance_show_cmdlist);
+If on, gdb will use displaced stepping to step over breakpoints if it is\n\
+supported by the target architecture. If off, gdb will not use displaced\n\
+stepping to step over breakpoints, even if such is supported by the target\n\
+architecture. If auto (which is the default), gdb will use displaced stepping\n\
+if the target architecture supports it and non-stop mode is active, but will not\n\
+use it in all-stop mode (see help set non-stop)."),
+ NULL,
+ show_can_use_displaced_stepping,
+ &setlist, &showlist);
+
+ add_setshow_enum_cmd ("exec-direction", class_run, exec_direction_names,
+ &exec_direction, _("Set direction of execution.\n\
+Options are 'forward' or 'reverse'."),
+ _("Show direction of execution (forward/reverse)."),
+ _("Tells gdb whether to execute forward or backward."),
+ set_exec_direction_func, show_exec_direction_func,
+ &setlist, &showlist);
/* ptid initializations */
null_ptid = ptid_build (0, 0, 0);
displaced_step_ptid = null_ptid;
observer_attach_thread_ptid_changed (infrun_thread_ptid_changed);
+ observer_attach_thread_stop_requested (infrun_thread_stop_requested);
}
projects / deliverable / binutils-gdb.git / blobdiff